100 lines
3.8 KiB
C
100 lines
3.8 KiB
C
/****************************************************************************
|
|
* Driver for Solarflare Solarstorm network controllers and boards
|
|
* Copyright 2005 Fen Systems Ltd.
|
|
* Copyright 2006-2010 Solarflare Communications Inc.
|
|
*
|
|
* This program is free software; you can redistribute it and/or modify it
|
|
* under the terms of the GNU General Public License version 2 as published
|
|
* by the Free Software Foundation, incorporated herein by reference.
|
|
*/
|
|
|
|
#ifndef EFX_SPI_H
|
|
#define EFX_SPI_H
|
|
|
|
#include "net_driver.h"
|
|
|
|
/**************************************************************************
|
|
*
|
|
* Basic SPI command set and bit definitions
|
|
*
|
|
*************************************************************************/
|
|
|
|
#define SPI_WRSR 0x01 /* Write status register */
|
|
#define SPI_WRITE 0x02 /* Write data to memory array */
|
|
#define SPI_READ 0x03 /* Read data from memory array */
|
|
#define SPI_WRDI 0x04 /* Reset write enable latch */
|
|
#define SPI_RDSR 0x05 /* Read status register */
|
|
#define SPI_WREN 0x06 /* Set write enable latch */
|
|
#define SPI_SST_EWSR 0x50 /* SST: Enable write to status register */
|
|
|
|
#define SPI_STATUS_WPEN 0x80 /* Write-protect pin enabled */
|
|
#define SPI_STATUS_BP2 0x10 /* Block protection bit 2 */
|
|
#define SPI_STATUS_BP1 0x08 /* Block protection bit 1 */
|
|
#define SPI_STATUS_BP0 0x04 /* Block protection bit 0 */
|
|
#define SPI_STATUS_WEN 0x02 /* State of the write enable latch */
|
|
#define SPI_STATUS_NRDY 0x01 /* Device busy flag */
|
|
|
|
/**
|
|
* struct efx_spi_device - an Efx SPI (Serial Peripheral Interface) device
|
|
* @device_id: Controller's id for the device
|
|
* @size: Size (in bytes)
|
|
* @addr_len: Number of address bytes in read/write commands
|
|
* @munge_address: Flag whether addresses should be munged.
|
|
* Some devices with 9-bit addresses (e.g. AT25040A EEPROM)
|
|
* use bit 3 of the command byte as address bit A8, rather
|
|
* than having a two-byte address. If this flag is set, then
|
|
* commands should be munged in this way.
|
|
* @erase_command: Erase command (or 0 if sector erase not needed).
|
|
* @erase_size: Erase sector size (in bytes)
|
|
* Erase commands affect sectors with this size and alignment.
|
|
* This must be a power of two.
|
|
* @block_size: Write block size (in bytes).
|
|
* Write commands are limited to blocks with this size and alignment.
|
|
*/
|
|
struct efx_spi_device {
|
|
int device_id;
|
|
unsigned int size;
|
|
unsigned int addr_len;
|
|
unsigned int munge_address:1;
|
|
u8 erase_command;
|
|
unsigned int erase_size;
|
|
unsigned int block_size;
|
|
};
|
|
|
|
static inline bool efx_spi_present(const struct efx_spi_device *spi)
|
|
{
|
|
return spi->size != 0;
|
|
}
|
|
|
|
int falcon_spi_cmd(struct efx_nic *efx,
|
|
const struct efx_spi_device *spi, unsigned int command,
|
|
int address, const void *in, void *out, size_t len);
|
|
int falcon_spi_wait_write(struct efx_nic *efx,
|
|
const struct efx_spi_device *spi);
|
|
int falcon_spi_read(struct efx_nic *efx,
|
|
const struct efx_spi_device *spi, loff_t start,
|
|
size_t len, size_t *retlen, u8 *buffer);
|
|
int falcon_spi_write(struct efx_nic *efx,
|
|
const struct efx_spi_device *spi, loff_t start,
|
|
size_t len, size_t *retlen, const u8 *buffer);
|
|
|
|
/*
|
|
* SFC4000 flash is partitioned into:
|
|
* 0-0x400 chip and board config (see falcon_hwdefs.h)
|
|
* 0x400-0x8000 unused (or may contain VPD if EEPROM not present)
|
|
* 0x8000-end boot code (mapped to PCI expansion ROM)
|
|
* SFC4000 small EEPROM (size < 0x400) is used for VPD only.
|
|
* SFC4000 large EEPROM (size >= 0x400) is partitioned into:
|
|
* 0-0x400 chip and board config
|
|
* configurable VPD
|
|
* 0x800-0x1800 boot config
|
|
* Aside from the chip and board config, all of these are optional and may
|
|
* be absent or truncated depending on the devices used.
|
|
*/
|
|
#define FALCON_NVCONFIG_END 0x400U
|
|
#define FALCON_FLASH_BOOTCODE_START 0x8000U
|
|
#define EFX_EEPROM_BOOTCONFIG_START 0x800U
|
|
#define EFX_EEPROM_BOOTCONFIG_END 0x1800U
|
|
|
|
#endif /* EFX_SPI_H */
|