2773 lines
87 KiB
C
2773 lines
87 KiB
C
/* SPDX-License-Identifier: GPL-2.0 */
|
|
|
|
/*
|
|
* xHCI host controller driver
|
|
*
|
|
* Copyright (C) 2008 Intel Corp.
|
|
*
|
|
* Author: Sarah Sharp
|
|
* Some code borrowed from the Linux EHCI driver.
|
|
*/
|
|
|
|
#ifndef __LINUX_XHCI_HCD_H
|
|
#define __LINUX_XHCI_HCD_H
|
|
|
|
#include <linux/usb.h>
|
|
#include <linux/timer.h>
|
|
#include <linux/kernel.h>
|
|
#include <linux/usb/hcd.h>
|
|
#include <linux/io-64-nonatomic-lo-hi.h>
|
|
|
|
/* Code sharing between pci-quirks and xhci hcd */
|
|
#include "xhci-ext-caps.h"
|
|
#include "pci-quirks.h"
|
|
|
|
/* max buffer size for trace and debug messages */
|
|
#define XHCI_MSG_MAX 500
|
|
|
|
/* xHCI PCI Configuration Registers */
|
|
#define XHCI_SBRN_OFFSET (0x60)
|
|
|
|
/* Max number of USB devices for any host controller - limit in section 6.1 */
|
|
#define MAX_HC_SLOTS 256
|
|
/* Section 5.3.3 - MaxPorts */
|
|
#define MAX_HC_PORTS 127
|
|
|
|
/*
|
|
* xHCI register interface.
|
|
* This corresponds to the eXtensible Host Controller Interface (xHCI)
|
|
* Revision 0.95 specification
|
|
*/
|
|
|
|
/**
|
|
* struct xhci_cap_regs - xHCI Host Controller Capability Registers.
|
|
* @hc_capbase: length of the capabilities register and HC version number
|
|
* @hcs_params1: HCSPARAMS1 - Structural Parameters 1
|
|
* @hcs_params2: HCSPARAMS2 - Structural Parameters 2
|
|
* @hcs_params3: HCSPARAMS3 - Structural Parameters 3
|
|
* @hcc_params: HCCPARAMS - Capability Parameters
|
|
* @db_off: DBOFF - Doorbell array offset
|
|
* @run_regs_off: RTSOFF - Runtime register space offset
|
|
* @hcc_params2: HCCPARAMS2 Capability Parameters 2, xhci 1.1 only
|
|
*/
|
|
struct xhci_cap_regs {
|
|
__le32 hc_capbase;
|
|
__le32 hcs_params1;
|
|
__le32 hcs_params2;
|
|
__le32 hcs_params3;
|
|
__le32 hcc_params;
|
|
__le32 db_off;
|
|
__le32 run_regs_off;
|
|
__le32 hcc_params2; /* xhci 1.1 */
|
|
/* Reserved up to (CAPLENGTH - 0x1C) */
|
|
};
|
|
|
|
/* hc_capbase bitmasks */
|
|
/* bits 7:0 - how long is the Capabilities register */
|
|
#define HC_LENGTH(p) XHCI_HC_LENGTH(p)
|
|
/* bits 31:16 */
|
|
#define HC_VERSION(p) (((p) >> 16) & 0xffff)
|
|
|
|
/* HCSPARAMS1 - hcs_params1 - bitmasks */
|
|
/* bits 0:7, Max Device Slots */
|
|
#define HCS_MAX_SLOTS(p) (((p) >> 0) & 0xff)
|
|
#define HCS_SLOTS_MASK 0xff
|
|
/* bits 8:18, Max Interrupters */
|
|
#define HCS_MAX_INTRS(p) (((p) >> 8) & 0x7ff)
|
|
/* bits 24:31, Max Ports - max value is 0x7F = 127 ports */
|
|
#define HCS_MAX_PORTS(p) (((p) >> 24) & 0x7f)
|
|
|
|
/* HCSPARAMS2 - hcs_params2 - bitmasks */
|
|
/* bits 0:3, frames or uframes that SW needs to queue transactions
|
|
* ahead of the HW to meet periodic deadlines */
|
|
#define HCS_IST(p) (((p) >> 0) & 0xf)
|
|
/* bits 4:7, max number of Event Ring segments */
|
|
#define HCS_ERST_MAX(p) (((p) >> 4) & 0xf)
|
|
/* bits 21:25 Hi 5 bits of Scratchpad buffers SW must allocate for the HW */
|
|
/* bit 26 Scratchpad restore - for save/restore HW state - not used yet */
|
|
/* bits 27:31 Lo 5 bits of Scratchpad buffers SW must allocate for the HW */
|
|
#define HCS_MAX_SCRATCHPAD(p) ((((p) >> 16) & 0x3e0) | (((p) >> 27) & 0x1f))
|
|
|
|
/* HCSPARAMS3 - hcs_params3 - bitmasks */
|
|
/* bits 0:7, Max U1 to U0 latency for the roothub ports */
|
|
#define HCS_U1_LATENCY(p) (((p) >> 0) & 0xff)
|
|
/* bits 16:31, Max U2 to U0 latency for the roothub ports */
|
|
#define HCS_U2_LATENCY(p) (((p) >> 16) & 0xffff)
|
|
|
|
/* HCCPARAMS - hcc_params - bitmasks */
|
|
/* true: HC can use 64-bit address pointers */
|
|
#define HCC_64BIT_ADDR(p) ((p) & (1 << 0))
|
|
/* true: HC can do bandwidth negotiation */
|
|
#define HCC_BANDWIDTH_NEG(p) ((p) & (1 << 1))
|
|
/* true: HC uses 64-byte Device Context structures
|
|
* FIXME 64-byte context structures aren't supported yet.
|
|
*/
|
|
#define HCC_64BYTE_CONTEXT(p) ((p) & (1 << 2))
|
|
/* true: HC has port power switches */
|
|
#define HCC_PPC(p) ((p) & (1 << 3))
|
|
/* true: HC has port indicators */
|
|
#define HCS_INDICATOR(p) ((p) & (1 << 4))
|
|
/* true: HC has Light HC Reset Capability */
|
|
#define HCC_LIGHT_RESET(p) ((p) & (1 << 5))
|
|
/* true: HC supports latency tolerance messaging */
|
|
#define HCC_LTC(p) ((p) & (1 << 6))
|
|
/* true: no secondary Stream ID Support */
|
|
#define HCC_NSS(p) ((p) & (1 << 7))
|
|
/* true: HC supports Stopped - Short Packet */
|
|
#define HCC_SPC(p) ((p) & (1 << 9))
|
|
/* true: HC has Contiguous Frame ID Capability */
|
|
#define HCC_CFC(p) ((p) & (1 << 11))
|
|
/* Max size for Primary Stream Arrays - 2^(n+1), where n is bits 12:15 */
|
|
#define HCC_MAX_PSA(p) (1 << ((((p) >> 12) & 0xf) + 1))
|
|
/* Extended Capabilities pointer from PCI base - section 5.3.6 */
|
|
#define HCC_EXT_CAPS(p) XHCI_HCC_EXT_CAPS(p)
|
|
|
|
#define CTX_SIZE(_hcc) (HCC_64BYTE_CONTEXT(_hcc) ? 64 : 32)
|
|
|
|
/* db_off bitmask - bits 0:1 reserved */
|
|
#define DBOFF_MASK (~0x3)
|
|
|
|
/* run_regs_off bitmask - bits 0:4 reserved */
|
|
#define RTSOFF_MASK (~0x1f)
|
|
|
|
/* HCCPARAMS2 - hcc_params2 - bitmasks */
|
|
/* true: HC supports U3 entry Capability */
|
|
#define HCC2_U3C(p) ((p) & (1 << 0))
|
|
/* true: HC supports Configure endpoint command Max exit latency too large */
|
|
#define HCC2_CMC(p) ((p) & (1 << 1))
|
|
/* true: HC supports Force Save context Capability */
|
|
#define HCC2_FSC(p) ((p) & (1 << 2))
|
|
/* true: HC supports Compliance Transition Capability */
|
|
#define HCC2_CTC(p) ((p) & (1 << 3))
|
|
/* true: HC support Large ESIT payload Capability > 48k */
|
|
#define HCC2_LEC(p) ((p) & (1 << 4))
|
|
/* true: HC support Configuration Information Capability */
|
|
#define HCC2_CIC(p) ((p) & (1 << 5))
|
|
/* true: HC support Extended TBC Capability, Isoc burst count > 65535 */
|
|
#define HCC2_ETC(p) ((p) & (1 << 6))
|
|
|
|
/* Number of registers per port */
|
|
#define NUM_PORT_REGS 4
|
|
|
|
#define PORTSC 0
|
|
#define PORTPMSC 1
|
|
#define PORTLI 2
|
|
#define PORTHLPMC 3
|
|
|
|
/**
|
|
* struct xhci_op_regs - xHCI Host Controller Operational Registers.
|
|
* @command: USBCMD - xHC command register
|
|
* @status: USBSTS - xHC status register
|
|
* @page_size: This indicates the page size that the host controller
|
|
* supports. If bit n is set, the HC supports a page size
|
|
* of 2^(n+12), up to a 128MB page size.
|
|
* 4K is the minimum page size.
|
|
* @cmd_ring: CRP - 64-bit Command Ring Pointer
|
|
* @dcbaa_ptr: DCBAAP - 64-bit Device Context Base Address Array Pointer
|
|
* @config_reg: CONFIG - Configure Register
|
|
* @port_status_base: PORTSCn - base address for Port Status and Control
|
|
* Each port has a Port Status and Control register,
|
|
* followed by a Port Power Management Status and Control
|
|
* register, a Port Link Info register, and a reserved
|
|
* register.
|
|
* @port_power_base: PORTPMSCn - base address for
|
|
* Port Power Management Status and Control
|
|
* @port_link_base: PORTLIn - base address for Port Link Info (current
|
|
* Link PM state and control) for USB 2.1 and USB 3.0
|
|
* devices.
|
|
*/
|
|
struct xhci_op_regs {
|
|
__le32 command;
|
|
__le32 status;
|
|
__le32 page_size;
|
|
__le32 reserved1;
|
|
__le32 reserved2;
|
|
__le32 dev_notification;
|
|
__le64 cmd_ring;
|
|
/* rsvd: offset 0x20-2F */
|
|
__le32 reserved3[4];
|
|
__le64 dcbaa_ptr;
|
|
__le32 config_reg;
|
|
/* rsvd: offset 0x3C-3FF */
|
|
__le32 reserved4[241];
|
|
/* port 1 registers, which serve as a base address for other ports */
|
|
__le32 port_status_base;
|
|
__le32 port_power_base;
|
|
__le32 port_link_base;
|
|
__le32 reserved5;
|
|
/* registers for ports 2-255 */
|
|
__le32 reserved6[NUM_PORT_REGS*254];
|
|
};
|
|
|
|
/* USBCMD - USB command - command bitmasks */
|
|
/* start/stop HC execution - do not write unless HC is halted*/
|
|
#define CMD_RUN XHCI_CMD_RUN
|
|
/* Reset HC - resets internal HC state machine and all registers (except
|
|
* PCI config regs). HC does NOT drive a USB reset on the downstream ports.
|
|
* The xHCI driver must reinitialize the xHC after setting this bit.
|
|
*/
|
|
#define CMD_RESET (1 << 1)
|
|
/* Event Interrupt Enable - a '1' allows interrupts from the host controller */
|
|
#define CMD_EIE XHCI_CMD_EIE
|
|
/* Host System Error Interrupt Enable - get out-of-band signal for HC errors */
|
|
#define CMD_HSEIE XHCI_CMD_HSEIE
|
|
/* bits 4:6 are reserved (and should be preserved on writes). */
|
|
/* light reset (port status stays unchanged) - reset completed when this is 0 */
|
|
#define CMD_LRESET (1 << 7)
|
|
/* host controller save/restore state. */
|
|
#define CMD_CSS (1 << 8)
|
|
#define CMD_CRS (1 << 9)
|
|
/* Enable Wrap Event - '1' means xHC generates an event when MFINDEX wraps. */
|
|
#define CMD_EWE XHCI_CMD_EWE
|
|
/* MFINDEX power management - '1' means xHC can stop MFINDEX counter if all root
|
|
* hubs are in U3 (selective suspend), disconnect, disabled, or powered-off.
|
|
* '0' means the xHC can power it off if all ports are in the disconnect,
|
|
* disabled, or powered-off state.
|
|
*/
|
|
#define CMD_PM_INDEX (1 << 11)
|
|
/* bit 14 Extended TBC Enable, changes Isoc TRB fields to support larger TBC */
|
|
#define CMD_ETE (1 << 14)
|
|
/* bits 15:31 are reserved (and should be preserved on writes). */
|
|
|
|
/* IMAN - Interrupt Management Register */
|
|
#define IMAN_IE (1 << 1)
|
|
#define IMAN_IP (1 << 0)
|
|
|
|
/* USBSTS - USB status - status bitmasks */
|
|
/* HC not running - set to 1 when run/stop bit is cleared. */
|
|
#define STS_HALT XHCI_STS_HALT
|
|
/* serious error, e.g. PCI parity error. The HC will clear the run/stop bit. */
|
|
#define STS_FATAL (1 << 2)
|
|
/* event interrupt - clear this prior to clearing any IP flags in IR set*/
|
|
#define STS_EINT (1 << 3)
|
|
/* port change detect */
|
|
#define STS_PORT (1 << 4)
|
|
/* bits 5:7 reserved and zeroed */
|
|
/* save state status - '1' means xHC is saving state */
|
|
#define STS_SAVE (1 << 8)
|
|
/* restore state status - '1' means xHC is restoring state */
|
|
#define STS_RESTORE (1 << 9)
|
|
/* true: save or restore error */
|
|
#define STS_SRE (1 << 10)
|
|
/* true: Controller Not Ready to accept doorbell or op reg writes after reset */
|
|
#define STS_CNR XHCI_STS_CNR
|
|
/* true: internal Host Controller Error - SW needs to reset and reinitialize */
|
|
#define STS_HCE (1 << 12)
|
|
/* bits 13:31 reserved and should be preserved */
|
|
|
|
/*
|
|
* DNCTRL - Device Notification Control Register - dev_notification bitmasks
|
|
* Generate a device notification event when the HC sees a transaction with a
|
|
* notification type that matches a bit set in this bit field.
|
|
*/
|
|
#define DEV_NOTE_MASK (0xffff)
|
|
#define ENABLE_DEV_NOTE(x) (1 << (x))
|
|
/* Most of the device notification types should only be used for debug.
|
|
* SW does need to pay attention to function wake notifications.
|
|
*/
|
|
#define DEV_NOTE_FWAKE ENABLE_DEV_NOTE(1)
|
|
|
|
/* CRCR - Command Ring Control Register - cmd_ring bitmasks */
|
|
/* bit 0 is the command ring cycle state */
|
|
/* stop ring operation after completion of the currently executing command */
|
|
#define CMD_RING_PAUSE (1 << 1)
|
|
/* stop ring immediately - abort the currently executing command */
|
|
#define CMD_RING_ABORT (1 << 2)
|
|
/* true: command ring is running */
|
|
#define CMD_RING_RUNNING (1 << 3)
|
|
/* bits 4:5 reserved and should be preserved */
|
|
/* Command Ring pointer - bit mask for the lower 32 bits. */
|
|
#define CMD_RING_RSVD_BITS (0x3f)
|
|
|
|
/* CONFIG - Configure Register - config_reg bitmasks */
|
|
/* bits 0:7 - maximum number of device slots enabled (NumSlotsEn) */
|
|
#define MAX_DEVS(p) ((p) & 0xff)
|
|
/* bit 8: U3 Entry Enabled, assert PLC when root port enters U3, xhci 1.1 */
|
|
#define CONFIG_U3E (1 << 8)
|
|
/* bit 9: Configuration Information Enable, xhci 1.1 */
|
|
#define CONFIG_CIE (1 << 9)
|
|
/* bits 10:31 - reserved and should be preserved */
|
|
|
|
/* PORTSC - Port Status and Control Register - port_status_base bitmasks */
|
|
/* true: device connected */
|
|
#define PORT_CONNECT (1 << 0)
|
|
/* true: port enabled */
|
|
#define PORT_PE (1 << 1)
|
|
/* bit 2 reserved and zeroed */
|
|
/* true: port has an over-current condition */
|
|
#define PORT_OC (1 << 3)
|
|
/* true: port reset signaling asserted */
|
|
#define PORT_RESET (1 << 4)
|
|
/* Port Link State - bits 5:8
|
|
* A read gives the current link PM state of the port,
|
|
* a write with Link State Write Strobe set sets the link state.
|
|
*/
|
|
#define PORT_PLS_MASK (0xf << 5)
|
|
#define XDEV_U0 (0x0 << 5)
|
|
#define XDEV_U1 (0x1 << 5)
|
|
#define XDEV_U2 (0x2 << 5)
|
|
#define XDEV_U3 (0x3 << 5)
|
|
#define XDEV_DISABLED (0x4 << 5)
|
|
#define XDEV_RXDETECT (0x5 << 5)
|
|
#define XDEV_INACTIVE (0x6 << 5)
|
|
#define XDEV_POLLING (0x7 << 5)
|
|
#define XDEV_RECOVERY (0x8 << 5)
|
|
#define XDEV_HOT_RESET (0x9 << 5)
|
|
#define XDEV_COMP_MODE (0xa << 5)
|
|
#define XDEV_TEST_MODE (0xb << 5)
|
|
#define XDEV_RESUME (0xf << 5)
|
|
|
|
/* true: port has power (see HCC_PPC) */
|
|
#define PORT_POWER (1 << 9)
|
|
/* bits 10:13 indicate device speed:
|
|
* 0 - undefined speed - port hasn't be initialized by a reset yet
|
|
* 1 - full speed
|
|
* 2 - low speed
|
|
* 3 - high speed
|
|
* 4 - super speed
|
|
* 5-15 reserved
|
|
*/
|
|
#define DEV_SPEED_MASK (0xf << 10)
|
|
#define XDEV_FS (0x1 << 10)
|
|
#define XDEV_LS (0x2 << 10)
|
|
#define XDEV_HS (0x3 << 10)
|
|
#define XDEV_SS (0x4 << 10)
|
|
#define XDEV_SSP (0x5 << 10)
|
|
#define DEV_UNDEFSPEED(p) (((p) & DEV_SPEED_MASK) == (0x0<<10))
|
|
#define DEV_FULLSPEED(p) (((p) & DEV_SPEED_MASK) == XDEV_FS)
|
|
#define DEV_LOWSPEED(p) (((p) & DEV_SPEED_MASK) == XDEV_LS)
|
|
#define DEV_HIGHSPEED(p) (((p) & DEV_SPEED_MASK) == XDEV_HS)
|
|
#define DEV_SUPERSPEED(p) (((p) & DEV_SPEED_MASK) == XDEV_SS)
|
|
#define DEV_SUPERSPEEDPLUS(p) (((p) & DEV_SPEED_MASK) == XDEV_SSP)
|
|
#define DEV_SUPERSPEED_ANY(p) (((p) & DEV_SPEED_MASK) >= XDEV_SS)
|
|
#define DEV_PORT_SPEED(p) (((p) >> 10) & 0x0f)
|
|
|
|
/* Bits 20:23 in the Slot Context are the speed for the device */
|
|
#define SLOT_SPEED_FS (XDEV_FS << 10)
|
|
#define SLOT_SPEED_LS (XDEV_LS << 10)
|
|
#define SLOT_SPEED_HS (XDEV_HS << 10)
|
|
#define SLOT_SPEED_SS (XDEV_SS << 10)
|
|
#define SLOT_SPEED_SSP (XDEV_SSP << 10)
|
|
/* Port Indicator Control */
|
|
#define PORT_LED_OFF (0 << 14)
|
|
#define PORT_LED_AMBER (1 << 14)
|
|
#define PORT_LED_GREEN (2 << 14)
|
|
#define PORT_LED_MASK (3 << 14)
|
|
/* Port Link State Write Strobe - set this when changing link state */
|
|
#define PORT_LINK_STROBE (1 << 16)
|
|
/* true: connect status change */
|
|
#define PORT_CSC (1 << 17)
|
|
/* true: port enable change */
|
|
#define PORT_PEC (1 << 18)
|
|
/* true: warm reset for a USB 3.0 device is done. A "hot" reset puts the port
|
|
* into an enabled state, and the device into the default state. A "warm" reset
|
|
* also resets the link, forcing the device through the link training sequence.
|
|
* SW can also look at the Port Reset register to see when warm reset is done.
|
|
*/
|
|
#define PORT_WRC (1 << 19)
|
|
/* true: over-current change */
|
|
#define PORT_OCC (1 << 20)
|
|
/* true: reset change - 1 to 0 transition of PORT_RESET */
|
|
#define PORT_RC (1 << 21)
|
|
/* port link status change - set on some port link state transitions:
|
|
* Transition Reason
|
|
* ------------------------------------------------------------------------------
|
|
* - U3 to Resume Wakeup signaling from a device
|
|
* - Resume to Recovery to U0 USB 3.0 device resume
|
|
* - Resume to U0 USB 2.0 device resume
|
|
* - U3 to Recovery to U0 Software resume of USB 3.0 device complete
|
|
* - U3 to U0 Software resume of USB 2.0 device complete
|
|
* - U2 to U0 L1 resume of USB 2.1 device complete
|
|
* - U0 to U0 (???) L1 entry rejection by USB 2.1 device
|
|
* - U0 to disabled L1 entry error with USB 2.1 device
|
|
* - Any state to inactive Error on USB 3.0 port
|
|
*/
|
|
#define PORT_PLC (1 << 22)
|
|
/* port configure error change - port failed to configure its link partner */
|
|
#define PORT_CEC (1 << 23)
|
|
#define PORT_CHANGE_MASK (PORT_CSC | PORT_PEC | PORT_WRC | PORT_OCC | \
|
|
PORT_RC | PORT_PLC | PORT_CEC)
|
|
|
|
|
|
/* Cold Attach Status - xHC can set this bit to report device attached during
|
|
* Sx state. Warm port reset should be perfomed to clear this bit and move port
|
|
* to connected state.
|
|
*/
|
|
#define PORT_CAS (1 << 24)
|
|
/* wake on connect (enable) */
|
|
#define PORT_WKCONN_E (1 << 25)
|
|
/* wake on disconnect (enable) */
|
|
#define PORT_WKDISC_E (1 << 26)
|
|
/* wake on over-current (enable) */
|
|
#define PORT_WKOC_E (1 << 27)
|
|
/* bits 28:29 reserved */
|
|
/* true: device is non-removable - for USB 3.0 roothub emulation */
|
|
#define PORT_DEV_REMOVE (1 << 30)
|
|
/* Initiate a warm port reset - complete when PORT_WRC is '1' */
|
|
#define PORT_WR (1 << 31)
|
|
|
|
/* We mark duplicate entries with -1 */
|
|
#define DUPLICATE_ENTRY ((u8)(-1))
|
|
|
|
/* Port Power Management Status and Control - port_power_base bitmasks */
|
|
/* Inactivity timer value for transitions into U1, in microseconds.
|
|
* Timeout can be up to 127us. 0xFF means an infinite timeout.
|
|
*/
|
|
#define PORT_U1_TIMEOUT(p) ((p) & 0xff)
|
|
#define PORT_U1_TIMEOUT_MASK 0xff
|
|
/* Inactivity timer value for transitions into U2 */
|
|
#define PORT_U2_TIMEOUT(p) (((p) & 0xff) << 8)
|
|
#define PORT_U2_TIMEOUT_MASK (0xff << 8)
|
|
/* Bits 24:31 for port testing */
|
|
|
|
/* USB2 Protocol PORTSPMSC */
|
|
#define PORT_L1S_MASK 7
|
|
#define PORT_L1S_SUCCESS 1
|
|
#define PORT_RWE (1 << 3)
|
|
#define PORT_HIRD(p) (((p) & 0xf) << 4)
|
|
#define PORT_HIRD_MASK (0xf << 4)
|
|
#define PORT_L1DS_MASK (0xff << 8)
|
|
#define PORT_L1DS(p) (((p) & 0xff) << 8)
|
|
#define PORT_HLE (1 << 16)
|
|
#define PORT_TEST_MODE_SHIFT 28
|
|
|
|
/* USB3 Protocol PORTLI Port Link Information */
|
|
#define PORT_RX_LANES(p) (((p) >> 16) & 0xf)
|
|
#define PORT_TX_LANES(p) (((p) >> 20) & 0xf)
|
|
|
|
/* USB2 Protocol PORTHLPMC */
|
|
#define PORT_HIRDM(p)((p) & 3)
|
|
#define PORT_L1_TIMEOUT(p)(((p) & 0xff) << 2)
|
|
#define PORT_BESLD(p)(((p) & 0xf) << 10)
|
|
|
|
/* use 512 microseconds as USB2 LPM L1 default timeout. */
|
|
#define XHCI_L1_TIMEOUT 512
|
|
|
|
/* Set default HIRD/BESL value to 4 (350/400us) for USB2 L1 LPM resume latency.
|
|
* Safe to use with mixed HIRD and BESL systems (host and device) and is used
|
|
* by other operating systems.
|
|
*
|
|
* XHCI 1.0 errata 8/14/12 Table 13 notes:
|
|
* "Software should choose xHC BESL/BESLD field values that do not violate a
|
|
* device's resume latency requirements,
|
|
* e.g. not program values > '4' if BLC = '1' and a HIRD device is attached,
|
|
* or not program values < '4' if BLC = '0' and a BESL device is attached.
|
|
*/
|
|
#define XHCI_DEFAULT_BESL 4
|
|
|
|
/*
|
|
* USB3 specification define a 360ms tPollingLFPSTiemout for USB3 ports
|
|
* to complete link training. usually link trainig completes much faster
|
|
* so check status 10 times with 36ms sleep in places we need to wait for
|
|
* polling to complete.
|
|
*/
|
|
#define XHCI_PORT_POLLING_LFPS_TIME 36
|
|
|
|
/**
|
|
* struct xhci_intr_reg - Interrupt Register Set
|
|
* @irq_pending: IMAN - Interrupt Management Register. Used to enable
|
|
* interrupts and check for pending interrupts.
|
|
* @irq_control: IMOD - Interrupt Moderation Register.
|
|
* Used to throttle interrupts.
|
|
* @erst_size: Number of segments in the Event Ring Segment Table (ERST).
|
|
* @erst_base: ERST base address.
|
|
* @erst_dequeue: Event ring dequeue pointer.
|
|
*
|
|
* Each interrupter (defined by a MSI-X vector) has an event ring and an Event
|
|
* Ring Segment Table (ERST) associated with it. The event ring is comprised of
|
|
* multiple segments of the same size. The HC places events on the ring and
|
|
* "updates the Cycle bit in the TRBs to indicate to software the current
|
|
* position of the Enqueue Pointer." The HCD (Linux) processes those events and
|
|
* updates the dequeue pointer.
|
|
*/
|
|
struct xhci_intr_reg {
|
|
__le32 irq_pending;
|
|
__le32 irq_control;
|
|
__le32 erst_size;
|
|
__le32 rsvd;
|
|
__le64 erst_base;
|
|
__le64 erst_dequeue;
|
|
};
|
|
|
|
/* irq_pending bitmasks */
|
|
#define ER_IRQ_PENDING(p) ((p) & 0x1)
|
|
/* bits 2:31 need to be preserved */
|
|
/* THIS IS BUGGY - FIXME - IP IS WRITE 1 TO CLEAR */
|
|
#define ER_IRQ_CLEAR(p) ((p) & 0xfffffffe)
|
|
#define ER_IRQ_ENABLE(p) ((ER_IRQ_CLEAR(p)) | 0x2)
|
|
#define ER_IRQ_DISABLE(p) ((ER_IRQ_CLEAR(p)) & ~(0x2))
|
|
|
|
/* irq_control bitmasks */
|
|
/* Minimum interval between interrupts (in 250ns intervals). The interval
|
|
* between interrupts will be longer if there are no events on the event ring.
|
|
* Default is 4000 (1 ms).
|
|
*/
|
|
#define ER_IRQ_INTERVAL_MASK (0xffff)
|
|
/* Counter used to count down the time to the next interrupt - HW use only */
|
|
#define ER_IRQ_COUNTER_MASK (0xffff << 16)
|
|
|
|
/* erst_size bitmasks */
|
|
/* Preserve bits 16:31 of erst_size */
|
|
#define ERST_SIZE_MASK (0xffff << 16)
|
|
|
|
/* erst_dequeue bitmasks */
|
|
/* Dequeue ERST Segment Index (DESI) - Segment number (or alias)
|
|
* where the current dequeue pointer lies. This is an optional HW hint.
|
|
*/
|
|
#define ERST_DESI_MASK (0x7)
|
|
/* Event Handler Busy (EHB) - is the event ring scheduled to be serviced by
|
|
* a work queue (or delayed service routine)?
|
|
*/
|
|
#define ERST_EHB (1 << 3)
|
|
#define ERST_PTR_MASK (0xf)
|
|
|
|
/**
|
|
* struct xhci_run_regs
|
|
* @microframe_index:
|
|
* MFINDEX - current microframe number
|
|
*
|
|
* Section 5.5 Host Controller Runtime Registers:
|
|
* "Software should read and write these registers using only Dword (32 bit)
|
|
* or larger accesses"
|
|
*/
|
|
struct xhci_run_regs {
|
|
__le32 microframe_index;
|
|
__le32 rsvd[7];
|
|
struct xhci_intr_reg ir_set[128];
|
|
};
|
|
|
|
/**
|
|
* struct doorbell_array
|
|
*
|
|
* Bits 0 - 7: Endpoint target
|
|
* Bits 8 - 15: RsvdZ
|
|
* Bits 16 - 31: Stream ID
|
|
*
|
|
* Section 5.6
|
|
*/
|
|
struct xhci_doorbell_array {
|
|
__le32 doorbell[256];
|
|
};
|
|
|
|
#define DB_VALUE(ep, stream) ((((ep) + 1) & 0xff) | ((stream) << 16))
|
|
#define DB_VALUE_HOST 0x00000000
|
|
|
|
/**
|
|
* struct xhci_protocol_caps
|
|
* @revision: major revision, minor revision, capability ID,
|
|
* and next capability pointer.
|
|
* @name_string: Four ASCII characters to say which spec this xHC
|
|
* follows, typically "USB ".
|
|
* @port_info: Port offset, count, and protocol-defined information.
|
|
*/
|
|
struct xhci_protocol_caps {
|
|
u32 revision;
|
|
u32 name_string;
|
|
u32 port_info;
|
|
};
|
|
|
|
#define XHCI_EXT_PORT_MAJOR(x) (((x) >> 24) & 0xff)
|
|
#define XHCI_EXT_PORT_MINOR(x) (((x) >> 16) & 0xff)
|
|
#define XHCI_EXT_PORT_PSIC(x) (((x) >> 28) & 0x0f)
|
|
#define XHCI_EXT_PORT_OFF(x) ((x) & 0xff)
|
|
#define XHCI_EXT_PORT_COUNT(x) (((x) >> 8) & 0xff)
|
|
|
|
#define XHCI_EXT_PORT_PSIV(x) (((x) >> 0) & 0x0f)
|
|
#define XHCI_EXT_PORT_PSIE(x) (((x) >> 4) & 0x03)
|
|
#define XHCI_EXT_PORT_PLT(x) (((x) >> 6) & 0x03)
|
|
#define XHCI_EXT_PORT_PFD(x) (((x) >> 8) & 0x01)
|
|
#define XHCI_EXT_PORT_LP(x) (((x) >> 14) & 0x03)
|
|
#define XHCI_EXT_PORT_PSIM(x) (((x) >> 16) & 0xffff)
|
|
|
|
#define PLT_MASK (0x03 << 6)
|
|
#define PLT_SYM (0x00 << 6)
|
|
#define PLT_ASYM_RX (0x02 << 6)
|
|
#define PLT_ASYM_TX (0x03 << 6)
|
|
|
|
/**
|
|
* struct xhci_container_ctx
|
|
* @type: Type of context. Used to calculated offsets to contained contexts.
|
|
* @size: Size of the context data
|
|
* @bytes: The raw context data given to HW
|
|
* @dma: dma address of the bytes
|
|
*
|
|
* Represents either a Device or Input context. Holds a pointer to the raw
|
|
* memory used for the context (bytes) and dma address of it (dma).
|
|
*/
|
|
struct xhci_container_ctx {
|
|
unsigned type;
|
|
#define XHCI_CTX_TYPE_DEVICE 0x1
|
|
#define XHCI_CTX_TYPE_INPUT 0x2
|
|
|
|
int size;
|
|
|
|
u8 *bytes;
|
|
dma_addr_t dma;
|
|
};
|
|
|
|
/**
|
|
* struct xhci_slot_ctx
|
|
* @dev_info: Route string, device speed, hub info, and last valid endpoint
|
|
* @dev_info2: Max exit latency for device number, root hub port number
|
|
* @tt_info: tt_info is used to construct split transaction tokens
|
|
* @dev_state: slot state and device address
|
|
*
|
|
* Slot Context - section 6.2.1.1. This assumes the HC uses 32-byte context
|
|
* structures. If the HC uses 64-byte contexts, there is an additional 32 bytes
|
|
* reserved at the end of the slot context for HC internal use.
|
|
*/
|
|
struct xhci_slot_ctx {
|
|
__le32 dev_info;
|
|
__le32 dev_info2;
|
|
__le32 tt_info;
|
|
__le32 dev_state;
|
|
/* offset 0x10 to 0x1f reserved for HC internal use */
|
|
__le32 reserved[4];
|
|
};
|
|
|
|
/* dev_info bitmasks */
|
|
/* Route String - 0:19 */
|
|
#define ROUTE_STRING_MASK (0xfffff)
|
|
/* Device speed - values defined by PORTSC Device Speed field - 20:23 */
|
|
#define DEV_SPEED (0xf << 20)
|
|
#define GET_DEV_SPEED(n) (((n) & DEV_SPEED) >> 20)
|
|
/* bit 24 reserved */
|
|
/* Is this LS/FS device connected through a HS hub? - bit 25 */
|
|
#define DEV_MTT (0x1 << 25)
|
|
/* Set if the device is a hub - bit 26 */
|
|
#define DEV_HUB (0x1 << 26)
|
|
/* Index of the last valid endpoint context in this device context - 27:31 */
|
|
#define LAST_CTX_MASK (0x1f << 27)
|
|
#define LAST_CTX(p) ((p) << 27)
|
|
#define LAST_CTX_TO_EP_NUM(p) (((p) >> 27) - 1)
|
|
#define SLOT_FLAG (1 << 0)
|
|
#define EP0_FLAG (1 << 1)
|
|
|
|
/* dev_info2 bitmasks */
|
|
/* Max Exit Latency (ms) - worst case time to wake up all links in dev path */
|
|
#define MAX_EXIT (0xffff)
|
|
/* Root hub port number that is needed to access the USB device */
|
|
#define ROOT_HUB_PORT(p) (((p) & 0xff) << 16)
|
|
#define DEVINFO_TO_ROOT_HUB_PORT(p) (((p) >> 16) & 0xff)
|
|
/* Maximum number of ports under a hub device */
|
|
#define XHCI_MAX_PORTS(p) (((p) & 0xff) << 24)
|
|
#define DEVINFO_TO_MAX_PORTS(p) (((p) & (0xff << 24)) >> 24)
|
|
|
|
/* tt_info bitmasks */
|
|
/*
|
|
* TT Hub Slot ID - for low or full speed devices attached to a high-speed hub
|
|
* The Slot ID of the hub that isolates the high speed signaling from
|
|
* this low or full-speed device. '0' if attached to root hub port.
|
|
*/
|
|
#define TT_SLOT (0xff)
|
|
/*
|
|
* The number of the downstream facing port of the high-speed hub
|
|
* '0' if the device is not low or full speed.
|
|
*/
|
|
#define TT_PORT (0xff << 8)
|
|
#define TT_THINK_TIME(p) (((p) & 0x3) << 16)
|
|
#define GET_TT_THINK_TIME(p) (((p) & (0x3 << 16)) >> 16)
|
|
|
|
/* dev_state bitmasks */
|
|
/* USB device address - assigned by the HC */
|
|
#define DEV_ADDR_MASK (0xff)
|
|
/* bits 8:26 reserved */
|
|
/* Slot state */
|
|
#define SLOT_STATE (0x1f << 27)
|
|
#define GET_SLOT_STATE(p) (((p) & (0x1f << 27)) >> 27)
|
|
|
|
#define SLOT_STATE_DISABLED 0
|
|
#define SLOT_STATE_ENABLED SLOT_STATE_DISABLED
|
|
#define SLOT_STATE_DEFAULT 1
|
|
#define SLOT_STATE_ADDRESSED 2
|
|
#define SLOT_STATE_CONFIGURED 3
|
|
|
|
/**
|
|
* struct xhci_ep_ctx
|
|
* @ep_info: endpoint state, streams, mult, and interval information.
|
|
* @ep_info2: information on endpoint type, max packet size, max burst size,
|
|
* error count, and whether the HC will force an event for all
|
|
* transactions.
|
|
* @deq: 64-bit ring dequeue pointer address. If the endpoint only
|
|
* defines one stream, this points to the endpoint transfer ring.
|
|
* Otherwise, it points to a stream context array, which has a
|
|
* ring pointer for each flow.
|
|
* @tx_info:
|
|
* Average TRB lengths for the endpoint ring and
|
|
* max payload within an Endpoint Service Interval Time (ESIT).
|
|
*
|
|
* Endpoint Context - section 6.2.1.2. This assumes the HC uses 32-byte context
|
|
* structures. If the HC uses 64-byte contexts, there is an additional 32 bytes
|
|
* reserved at the end of the endpoint context for HC internal use.
|
|
*/
|
|
struct xhci_ep_ctx {
|
|
__le32 ep_info;
|
|
__le32 ep_info2;
|
|
__le64 deq;
|
|
__le32 tx_info;
|
|
/* offset 0x14 - 0x1f reserved for HC internal use */
|
|
__le32 reserved[3];
|
|
};
|
|
|
|
/* ep_info bitmasks */
|
|
/*
|
|
* Endpoint State - bits 0:2
|
|
* 0 - disabled
|
|
* 1 - running
|
|
* 2 - halted due to halt condition - ok to manipulate endpoint ring
|
|
* 3 - stopped
|
|
* 4 - TRB error
|
|
* 5-7 - reserved
|
|
*/
|
|
#define EP_STATE_MASK (0x7)
|
|
#define EP_STATE_DISABLED 0
|
|
#define EP_STATE_RUNNING 1
|
|
#define EP_STATE_HALTED 2
|
|
#define EP_STATE_STOPPED 3
|
|
#define EP_STATE_ERROR 4
|
|
#define GET_EP_CTX_STATE(ctx) (le32_to_cpu((ctx)->ep_info) & EP_STATE_MASK)
|
|
|
|
/* Mult - Max number of burtst within an interval, in EP companion desc. */
|
|
#define EP_MULT(p) (((p) & 0x3) << 8)
|
|
#define CTX_TO_EP_MULT(p) (((p) >> 8) & 0x3)
|
|
/* bits 10:14 are Max Primary Streams */
|
|
/* bit 15 is Linear Stream Array */
|
|
/* Interval - period between requests to an endpoint - 125u increments. */
|
|
#define EP_INTERVAL(p) (((p) & 0xff) << 16)
|
|
#define EP_INTERVAL_TO_UFRAMES(p) (1 << (((p) >> 16) & 0xff))
|
|
#define CTX_TO_EP_INTERVAL(p) (((p) >> 16) & 0xff)
|
|
#define EP_MAXPSTREAMS_MASK (0x1f << 10)
|
|
#define EP_MAXPSTREAMS(p) (((p) << 10) & EP_MAXPSTREAMS_MASK)
|
|
#define CTX_TO_EP_MAXPSTREAMS(p) (((p) & EP_MAXPSTREAMS_MASK) >> 10)
|
|
/* Endpoint is set up with a Linear Stream Array (vs. Secondary Stream Array) */
|
|
#define EP_HAS_LSA (1 << 15)
|
|
/* hosts with LEC=1 use bits 31:24 as ESIT high bits. */
|
|
#define CTX_TO_MAX_ESIT_PAYLOAD_HI(p) (((p) >> 24) & 0xff)
|
|
|
|
/* ep_info2 bitmasks */
|
|
/*
|
|
* Force Event - generate transfer events for all TRBs for this endpoint
|
|
* This will tell the HC to ignore the IOC and ISP flags (for debugging only).
|
|
*/
|
|
#define FORCE_EVENT (0x1)
|
|
#define ERROR_COUNT(p) (((p) & 0x3) << 1)
|
|
#define CTX_TO_EP_TYPE(p) (((p) >> 3) & 0x7)
|
|
#define EP_TYPE(p) ((p) << 3)
|
|
#define ISOC_OUT_EP 1
|
|
#define BULK_OUT_EP 2
|
|
#define INT_OUT_EP 3
|
|
#define CTRL_EP 4
|
|
#define ISOC_IN_EP 5
|
|
#define BULK_IN_EP 6
|
|
#define INT_IN_EP 7
|
|
/* bit 6 reserved */
|
|
/* bit 7 is Host Initiate Disable - for disabling stream selection */
|
|
#define MAX_BURST(p) (((p)&0xff) << 8)
|
|
#define CTX_TO_MAX_BURST(p) (((p) >> 8) & 0xff)
|
|
#define MAX_PACKET(p) (((p)&0xffff) << 16)
|
|
#define MAX_PACKET_MASK (0xffff << 16)
|
|
#define MAX_PACKET_DECODED(p) (((p) >> 16) & 0xffff)
|
|
|
|
/* tx_info bitmasks */
|
|
#define EP_AVG_TRB_LENGTH(p) ((p) & 0xffff)
|
|
#define EP_MAX_ESIT_PAYLOAD_LO(p) (((p) & 0xffff) << 16)
|
|
#define EP_MAX_ESIT_PAYLOAD_HI(p) ((((p) >> 16) & 0xff) << 24)
|
|
#define CTX_TO_MAX_ESIT_PAYLOAD(p) (((p) >> 16) & 0xffff)
|
|
|
|
/* deq bitmasks */
|
|
#define EP_CTX_CYCLE_MASK (1 << 0)
|
|
#define SCTX_DEQ_MASK (~0xfL)
|
|
|
|
|
|
/**
|
|
* struct xhci_input_control_context
|
|
* Input control context; see section 6.2.5.
|
|
*
|
|
* @drop_context: set the bit of the endpoint context you want to disable
|
|
* @add_context: set the bit of the endpoint context you want to enable
|
|
*/
|
|
struct xhci_input_control_ctx {
|
|
__le32 drop_flags;
|
|
__le32 add_flags;
|
|
__le32 rsvd2[6];
|
|
};
|
|
|
|
#define EP_IS_ADDED(ctrl_ctx, i) \
|
|
(le32_to_cpu(ctrl_ctx->add_flags) & (1 << (i + 1)))
|
|
#define EP_IS_DROPPED(ctrl_ctx, i) \
|
|
(le32_to_cpu(ctrl_ctx->drop_flags) & (1 << (i + 1)))
|
|
|
|
/* Represents everything that is needed to issue a command on the command ring.
|
|
* It's useful to pre-allocate these for commands that cannot fail due to
|
|
* out-of-memory errors, like freeing streams.
|
|
*/
|
|
struct xhci_command {
|
|
/* Input context for changing device state */
|
|
struct xhci_container_ctx *in_ctx;
|
|
u32 status;
|
|
int slot_id;
|
|
/* If completion is null, no one is waiting on this command
|
|
* and the structure can be freed after the command completes.
|
|
*/
|
|
struct completion *completion;
|
|
union xhci_trb *command_trb;
|
|
struct list_head cmd_list;
|
|
};
|
|
|
|
/* drop context bitmasks */
|
|
#define DROP_EP(x) (0x1 << x)
|
|
/* add context bitmasks */
|
|
#define ADD_EP(x) (0x1 << x)
|
|
|
|
struct xhci_stream_ctx {
|
|
/* 64-bit stream ring address, cycle state, and stream type */
|
|
__le64 stream_ring;
|
|
/* offset 0x14 - 0x1f reserved for HC internal use */
|
|
__le32 reserved[2];
|
|
};
|
|
|
|
/* Stream Context Types (section 6.4.1) - bits 3:1 of stream ctx deq ptr */
|
|
#define SCT_FOR_CTX(p) (((p) & 0x7) << 1)
|
|
/* Secondary stream array type, dequeue pointer is to a transfer ring */
|
|
#define SCT_SEC_TR 0
|
|
/* Primary stream array type, dequeue pointer is to a transfer ring */
|
|
#define SCT_PRI_TR 1
|
|
/* Dequeue pointer is for a secondary stream array (SSA) with 8 entries */
|
|
#define SCT_SSA_8 2
|
|
#define SCT_SSA_16 3
|
|
#define SCT_SSA_32 4
|
|
#define SCT_SSA_64 5
|
|
#define SCT_SSA_128 6
|
|
#define SCT_SSA_256 7
|
|
|
|
/* Assume no secondary streams for now */
|
|
struct xhci_stream_info {
|
|
struct xhci_ring **stream_rings;
|
|
/* Number of streams, including stream 0 (which drivers can't use) */
|
|
unsigned int num_streams;
|
|
/* The stream context array may be bigger than
|
|
* the number of streams the driver asked for
|
|
*/
|
|
struct xhci_stream_ctx *stream_ctx_array;
|
|
unsigned int num_stream_ctxs;
|
|
dma_addr_t ctx_array_dma;
|
|
/* For mapping physical TRB addresses to segments in stream rings */
|
|
struct radix_tree_root trb_address_map;
|
|
struct xhci_command *free_streams_command;
|
|
};
|
|
|
|
#define SMALL_STREAM_ARRAY_SIZE 256
|
|
#define MEDIUM_STREAM_ARRAY_SIZE 1024
|
|
|
|
/* Some Intel xHCI host controllers need software to keep track of the bus
|
|
* bandwidth. Keep track of endpoint info here. Each root port is allocated
|
|
* the full bus bandwidth. We must also treat TTs (including each port under a
|
|
* multi-TT hub) as a separate bandwidth domain. The direct memory interface
|
|
* (DMI) also limits the total bandwidth (across all domains) that can be used.
|
|
*/
|
|
struct xhci_bw_info {
|
|
/* ep_interval is zero-based */
|
|
unsigned int ep_interval;
|
|
/* mult and num_packets are one-based */
|
|
unsigned int mult;
|
|
unsigned int num_packets;
|
|
unsigned int max_packet_size;
|
|
unsigned int max_esit_payload;
|
|
unsigned int type;
|
|
};
|
|
|
|
/* "Block" sizes in bytes the hardware uses for different device speeds.
|
|
* The logic in this part of the hardware limits the number of bits the hardware
|
|
* can use, so must represent bandwidth in a less precise manner to mimic what
|
|
* the scheduler hardware computes.
|
|
*/
|
|
#define FS_BLOCK 1
|
|
#define HS_BLOCK 4
|
|
#define SS_BLOCK 16
|
|
#define DMI_BLOCK 32
|
|
|
|
/* Each device speed has a protocol overhead (CRC, bit stuffing, etc) associated
|
|
* with each byte transferred. SuperSpeed devices have an initial overhead to
|
|
* set up bursts. These are in blocks, see above. LS overhead has already been
|
|
* translated into FS blocks.
|
|
*/
|
|
#define DMI_OVERHEAD 8
|
|
#define DMI_OVERHEAD_BURST 4
|
|
#define SS_OVERHEAD 8
|
|
#define SS_OVERHEAD_BURST 32
|
|
#define HS_OVERHEAD 26
|
|
#define FS_OVERHEAD 20
|
|
#define LS_OVERHEAD 128
|
|
/* The TTs need to claim roughly twice as much bandwidth (94 bytes per
|
|
* microframe ~= 24Mbps) of the HS bus as the devices can actually use because
|
|
* of overhead associated with split transfers crossing microframe boundaries.
|
|
* 31 blocks is pure protocol overhead.
|
|
*/
|
|
#define TT_HS_OVERHEAD (31 + 94)
|
|
#define TT_DMI_OVERHEAD (25 + 12)
|
|
|
|
/* Bandwidth limits in blocks */
|
|
#define FS_BW_LIMIT 1285
|
|
#define TT_BW_LIMIT 1320
|
|
#define HS_BW_LIMIT 1607
|
|
#define SS_BW_LIMIT_IN 3906
|
|
#define DMI_BW_LIMIT_IN 3906
|
|
#define SS_BW_LIMIT_OUT 3906
|
|
#define DMI_BW_LIMIT_OUT 3906
|
|
|
|
/* Percentage of bus bandwidth reserved for non-periodic transfers */
|
|
#define FS_BW_RESERVED 10
|
|
#define HS_BW_RESERVED 20
|
|
#define SS_BW_RESERVED 10
|
|
|
|
struct xhci_virt_ep {
|
|
struct xhci_virt_device *vdev; /* parent */
|
|
unsigned int ep_index;
|
|
struct xhci_ring *ring;
|
|
/* Related to endpoints that are configured to use stream IDs only */
|
|
struct xhci_stream_info *stream_info;
|
|
/* Temporary storage in case the configure endpoint command fails and we
|
|
* have to restore the device state to the previous state
|
|
*/
|
|
struct xhci_ring *new_ring;
|
|
unsigned int ep_state;
|
|
#define SET_DEQ_PENDING (1 << 0)
|
|
#define EP_HALTED (1 << 1) /* For stall handling */
|
|
#define EP_STOP_CMD_PENDING (1 << 2) /* For URB cancellation */
|
|
/* Transitioning the endpoint to using streams, don't enqueue URBs */
|
|
#define EP_GETTING_STREAMS (1 << 3)
|
|
#define EP_HAS_STREAMS (1 << 4)
|
|
/* Transitioning the endpoint to not using streams, don't enqueue URBs */
|
|
#define EP_GETTING_NO_STREAMS (1 << 5)
|
|
#define EP_HARD_CLEAR_TOGGLE (1 << 6)
|
|
#define EP_SOFT_CLEAR_TOGGLE (1 << 7)
|
|
/* usb_hub_clear_tt_buffer is in progress */
|
|
#define EP_CLEARING_TT (1 << 8)
|
|
/* ---- Related to URB cancellation ---- */
|
|
struct list_head cancelled_td_list;
|
|
/* Watchdog timer for stop endpoint command to cancel URBs */
|
|
struct timer_list stop_cmd_timer;
|
|
struct xhci_hcd *xhci;
|
|
/* Dequeue pointer and dequeue segment for a submitted Set TR Dequeue
|
|
* command. We'll need to update the ring's dequeue segment and dequeue
|
|
* pointer after the command completes.
|
|
*/
|
|
struct xhci_segment *queued_deq_seg;
|
|
union xhci_trb *queued_deq_ptr;
|
|
/*
|
|
* Sometimes the xHC can not process isochronous endpoint ring quickly
|
|
* enough, and it will miss some isoc tds on the ring and generate
|
|
* a Missed Service Error Event.
|
|
* Set skip flag when receive a Missed Service Error Event and
|
|
* process the missed tds on the endpoint ring.
|
|
*/
|
|
bool skip;
|
|
/* Bandwidth checking storage */
|
|
struct xhci_bw_info bw_info;
|
|
struct list_head bw_endpoint_list;
|
|
/* Isoch Frame ID checking storage */
|
|
int next_frame_id;
|
|
/* Use new Isoch TRB layout needed for extended TBC support */
|
|
bool use_extended_tbc;
|
|
};
|
|
|
|
enum xhci_overhead_type {
|
|
LS_OVERHEAD_TYPE = 0,
|
|
FS_OVERHEAD_TYPE,
|
|
HS_OVERHEAD_TYPE,
|
|
};
|
|
|
|
struct xhci_interval_bw {
|
|
unsigned int num_packets;
|
|
/* Sorted by max packet size.
|
|
* Head of the list is the greatest max packet size.
|
|
*/
|
|
struct list_head endpoints;
|
|
/* How many endpoints of each speed are present. */
|
|
unsigned int overhead[3];
|
|
};
|
|
|
|
#define XHCI_MAX_INTERVAL 16
|
|
|
|
struct xhci_interval_bw_table {
|
|
unsigned int interval0_esit_payload;
|
|
struct xhci_interval_bw interval_bw[XHCI_MAX_INTERVAL];
|
|
/* Includes reserved bandwidth for async endpoints */
|
|
unsigned int bw_used;
|
|
unsigned int ss_bw_in;
|
|
unsigned int ss_bw_out;
|
|
};
|
|
|
|
#define EP_CTX_PER_DEV 31
|
|
|
|
struct xhci_virt_device {
|
|
int slot_id;
|
|
struct usb_device *udev;
|
|
/*
|
|
* Commands to the hardware are passed an "input context" that
|
|
* tells the hardware what to change in its data structures.
|
|
* The hardware will return changes in an "output context" that
|
|
* software must allocate for the hardware. We need to keep
|
|
* track of input and output contexts separately because
|
|
* these commands might fail and we don't trust the hardware.
|
|
*/
|
|
struct xhci_container_ctx *out_ctx;
|
|
/* Used for addressing devices and configuration changes */
|
|
struct xhci_container_ctx *in_ctx;
|
|
struct xhci_virt_ep eps[EP_CTX_PER_DEV];
|
|
u8 fake_port;
|
|
u8 real_port;
|
|
struct xhci_interval_bw_table *bw_table;
|
|
struct xhci_tt_bw_info *tt_info;
|
|
/*
|
|
* flags for state tracking based on events and issued commands.
|
|
* Software can not rely on states from output contexts because of
|
|
* latency between events and xHC updating output context values.
|
|
* See xhci 1.1 section 4.8.3 for more details
|
|
*/
|
|
unsigned long flags;
|
|
#define VDEV_PORT_ERROR BIT(0) /* Port error, link inactive */
|
|
|
|
/* The current max exit latency for the enabled USB3 link states. */
|
|
u16 current_mel;
|
|
/* Used for the debugfs interfaces. */
|
|
void *debugfs_private;
|
|
};
|
|
|
|
/*
|
|
* For each roothub, keep track of the bandwidth information for each periodic
|
|
* interval.
|
|
*
|
|
* If a high speed hub is attached to the roothub, each TT associated with that
|
|
* hub is a separate bandwidth domain. The interval information for the
|
|
* endpoints on the devices under that TT will appear in the TT structure.
|
|
*/
|
|
struct xhci_root_port_bw_info {
|
|
struct list_head tts;
|
|
unsigned int num_active_tts;
|
|
struct xhci_interval_bw_table bw_table;
|
|
};
|
|
|
|
struct xhci_tt_bw_info {
|
|
struct list_head tt_list;
|
|
int slot_id;
|
|
int ttport;
|
|
struct xhci_interval_bw_table bw_table;
|
|
int active_eps;
|
|
};
|
|
|
|
|
|
/**
|
|
* struct xhci_device_context_array
|
|
* @dev_context_ptr array of 64-bit DMA addresses for device contexts
|
|
*/
|
|
struct xhci_device_context_array {
|
|
/* 64-bit device addresses; we only write 32-bit addresses */
|
|
__le64 dev_context_ptrs[MAX_HC_SLOTS];
|
|
/* private xHCD pointers */
|
|
dma_addr_t dma;
|
|
};
|
|
/* TODO: write function to set the 64-bit device DMA address */
|
|
/*
|
|
* TODO: change this to be dynamically sized at HC mem init time since the HC
|
|
* might not be able to handle the maximum number of devices possible.
|
|
*/
|
|
|
|
|
|
struct xhci_transfer_event {
|
|
/* 64-bit buffer address, or immediate data */
|
|
__le64 buffer;
|
|
__le32 transfer_len;
|
|
/* This field is interpreted differently based on the type of TRB */
|
|
__le32 flags;
|
|
};
|
|
|
|
/* Transfer event TRB length bit mask */
|
|
/* bits 0:23 */
|
|
#define EVENT_TRB_LEN(p) ((p) & 0xffffff)
|
|
|
|
/** Transfer Event bit fields **/
|
|
#define TRB_TO_EP_ID(p) (((p) >> 16) & 0x1f)
|
|
|
|
/* Completion Code - only applicable for some types of TRBs */
|
|
#define COMP_CODE_MASK (0xff << 24)
|
|
#define GET_COMP_CODE(p) (((p) & COMP_CODE_MASK) >> 24)
|
|
#define COMP_INVALID 0
|
|
#define COMP_SUCCESS 1
|
|
#define COMP_DATA_BUFFER_ERROR 2
|
|
#define COMP_BABBLE_DETECTED_ERROR 3
|
|
#define COMP_USB_TRANSACTION_ERROR 4
|
|
#define COMP_TRB_ERROR 5
|
|
#define COMP_STALL_ERROR 6
|
|
#define COMP_RESOURCE_ERROR 7
|
|
#define COMP_BANDWIDTH_ERROR 8
|
|
#define COMP_NO_SLOTS_AVAILABLE_ERROR 9
|
|
#define COMP_INVALID_STREAM_TYPE_ERROR 10
|
|
#define COMP_SLOT_NOT_ENABLED_ERROR 11
|
|
#define COMP_ENDPOINT_NOT_ENABLED_ERROR 12
|
|
#define COMP_SHORT_PACKET 13
|
|
#define COMP_RING_UNDERRUN 14
|
|
#define COMP_RING_OVERRUN 15
|
|
#define COMP_VF_EVENT_RING_FULL_ERROR 16
|
|
#define COMP_PARAMETER_ERROR 17
|
|
#define COMP_BANDWIDTH_OVERRUN_ERROR 18
|
|
#define COMP_CONTEXT_STATE_ERROR 19
|
|
#define COMP_NO_PING_RESPONSE_ERROR 20
|
|
#define COMP_EVENT_RING_FULL_ERROR 21
|
|
#define COMP_INCOMPATIBLE_DEVICE_ERROR 22
|
|
#define COMP_MISSED_SERVICE_ERROR 23
|
|
#define COMP_COMMAND_RING_STOPPED 24
|
|
#define COMP_COMMAND_ABORTED 25
|
|
#define COMP_STOPPED 26
|
|
#define COMP_STOPPED_LENGTH_INVALID 27
|
|
#define COMP_STOPPED_SHORT_PACKET 28
|
|
#define COMP_MAX_EXIT_LATENCY_TOO_LARGE_ERROR 29
|
|
#define COMP_ISOCH_BUFFER_OVERRUN 31
|
|
#define COMP_EVENT_LOST_ERROR 32
|
|
#define COMP_UNDEFINED_ERROR 33
|
|
#define COMP_INVALID_STREAM_ID_ERROR 34
|
|
#define COMP_SECONDARY_BANDWIDTH_ERROR 35
|
|
#define COMP_SPLIT_TRANSACTION_ERROR 36
|
|
|
|
static inline const char *xhci_trb_comp_code_string(u8 status)
|
|
{
|
|
switch (status) {
|
|
case COMP_INVALID:
|
|
return "Invalid";
|
|
case COMP_SUCCESS:
|
|
return "Success";
|
|
case COMP_DATA_BUFFER_ERROR:
|
|
return "Data Buffer Error";
|
|
case COMP_BABBLE_DETECTED_ERROR:
|
|
return "Babble Detected";
|
|
case COMP_USB_TRANSACTION_ERROR:
|
|
return "USB Transaction Error";
|
|
case COMP_TRB_ERROR:
|
|
return "TRB Error";
|
|
case COMP_STALL_ERROR:
|
|
return "Stall Error";
|
|
case COMP_RESOURCE_ERROR:
|
|
return "Resource Error";
|
|
case COMP_BANDWIDTH_ERROR:
|
|
return "Bandwidth Error";
|
|
case COMP_NO_SLOTS_AVAILABLE_ERROR:
|
|
return "No Slots Available Error";
|
|
case COMP_INVALID_STREAM_TYPE_ERROR:
|
|
return "Invalid Stream Type Error";
|
|
case COMP_SLOT_NOT_ENABLED_ERROR:
|
|
return "Slot Not Enabled Error";
|
|
case COMP_ENDPOINT_NOT_ENABLED_ERROR:
|
|
return "Endpoint Not Enabled Error";
|
|
case COMP_SHORT_PACKET:
|
|
return "Short Packet";
|
|
case COMP_RING_UNDERRUN:
|
|
return "Ring Underrun";
|
|
case COMP_RING_OVERRUN:
|
|
return "Ring Overrun";
|
|
case COMP_VF_EVENT_RING_FULL_ERROR:
|
|
return "VF Event Ring Full Error";
|
|
case COMP_PARAMETER_ERROR:
|
|
return "Parameter Error";
|
|
case COMP_BANDWIDTH_OVERRUN_ERROR:
|
|
return "Bandwidth Overrun Error";
|
|
case COMP_CONTEXT_STATE_ERROR:
|
|
return "Context State Error";
|
|
case COMP_NO_PING_RESPONSE_ERROR:
|
|
return "No Ping Response Error";
|
|
case COMP_EVENT_RING_FULL_ERROR:
|
|
return "Event Ring Full Error";
|
|
case COMP_INCOMPATIBLE_DEVICE_ERROR:
|
|
return "Incompatible Device Error";
|
|
case COMP_MISSED_SERVICE_ERROR:
|
|
return "Missed Service Error";
|
|
case COMP_COMMAND_RING_STOPPED:
|
|
return "Command Ring Stopped";
|
|
case COMP_COMMAND_ABORTED:
|
|
return "Command Aborted";
|
|
case COMP_STOPPED:
|
|
return "Stopped";
|
|
case COMP_STOPPED_LENGTH_INVALID:
|
|
return "Stopped - Length Invalid";
|
|
case COMP_STOPPED_SHORT_PACKET:
|
|
return "Stopped - Short Packet";
|
|
case COMP_MAX_EXIT_LATENCY_TOO_LARGE_ERROR:
|
|
return "Max Exit Latency Too Large Error";
|
|
case COMP_ISOCH_BUFFER_OVERRUN:
|
|
return "Isoch Buffer Overrun";
|
|
case COMP_EVENT_LOST_ERROR:
|
|
return "Event Lost Error";
|
|
case COMP_UNDEFINED_ERROR:
|
|
return "Undefined Error";
|
|
case COMP_INVALID_STREAM_ID_ERROR:
|
|
return "Invalid Stream ID Error";
|
|
case COMP_SECONDARY_BANDWIDTH_ERROR:
|
|
return "Secondary Bandwidth Error";
|
|
case COMP_SPLIT_TRANSACTION_ERROR:
|
|
return "Split Transaction Error";
|
|
default:
|
|
return "Unknown!!";
|
|
}
|
|
}
|
|
|
|
struct xhci_link_trb {
|
|
/* 64-bit segment pointer*/
|
|
__le64 segment_ptr;
|
|
__le32 intr_target;
|
|
__le32 control;
|
|
};
|
|
|
|
/* control bitfields */
|
|
#define LINK_TOGGLE (0x1<<1)
|
|
|
|
/* Command completion event TRB */
|
|
struct xhci_event_cmd {
|
|
/* Pointer to command TRB, or the value passed by the event data trb */
|
|
__le64 cmd_trb;
|
|
__le32 status;
|
|
__le32 flags;
|
|
};
|
|
|
|
/* flags bitmasks */
|
|
|
|
/* Address device - disable SetAddress */
|
|
#define TRB_BSR (1<<9)
|
|
|
|
/* Configure Endpoint - Deconfigure */
|
|
#define TRB_DC (1<<9)
|
|
|
|
/* Stop Ring - Transfer State Preserve */
|
|
#define TRB_TSP (1<<9)
|
|
|
|
enum xhci_ep_reset_type {
|
|
EP_HARD_RESET,
|
|
EP_SOFT_RESET,
|
|
};
|
|
|
|
/* Force Event */
|
|
#define TRB_TO_VF_INTR_TARGET(p) (((p) & (0x3ff << 22)) >> 22)
|
|
#define TRB_TO_VF_ID(p) (((p) & (0xff << 16)) >> 16)
|
|
|
|
/* Set Latency Tolerance Value */
|
|
#define TRB_TO_BELT(p) (((p) & (0xfff << 16)) >> 16)
|
|
|
|
/* Get Port Bandwidth */
|
|
#define TRB_TO_DEV_SPEED(p) (((p) & (0xf << 16)) >> 16)
|
|
|
|
/* Force Header */
|
|
#define TRB_TO_PACKET_TYPE(p) ((p) & 0x1f)
|
|
#define TRB_TO_ROOTHUB_PORT(p) (((p) & (0xff << 24)) >> 24)
|
|
|
|
enum xhci_setup_dev {
|
|
SETUP_CONTEXT_ONLY,
|
|
SETUP_CONTEXT_ADDRESS,
|
|
};
|
|
|
|
/* bits 16:23 are the virtual function ID */
|
|
/* bits 24:31 are the slot ID */
|
|
#define TRB_TO_SLOT_ID(p) (((p) & (0xff<<24)) >> 24)
|
|
#define SLOT_ID_FOR_TRB(p) (((p) & 0xff) << 24)
|
|
|
|
/* Stop Endpoint TRB - ep_index to endpoint ID for this TRB */
|
|
#define TRB_TO_EP_INDEX(p) ((((p) & (0x1f << 16)) >> 16) - 1)
|
|
#define EP_ID_FOR_TRB(p) ((((p) + 1) & 0x1f) << 16)
|
|
|
|
#define SUSPEND_PORT_FOR_TRB(p) (((p) & 1) << 23)
|
|
#define TRB_TO_SUSPEND_PORT(p) (((p) & (1 << 23)) >> 23)
|
|
#define LAST_EP_INDEX 30
|
|
|
|
/* Set TR Dequeue Pointer command TRB fields, 6.4.3.9 */
|
|
#define TRB_TO_STREAM_ID(p) ((((p) & (0xffff << 16)) >> 16))
|
|
#define STREAM_ID_FOR_TRB(p) ((((p)) & 0xffff) << 16)
|
|
#define SCT_FOR_TRB(p) (((p) << 1) & 0x7)
|
|
|
|
/* Link TRB specific fields */
|
|
#define TRB_TC (1<<1)
|
|
|
|
/* Port Status Change Event TRB fields */
|
|
/* Port ID - bits 31:24 */
|
|
#define GET_PORT_ID(p) (((p) & (0xff << 24)) >> 24)
|
|
|
|
#define EVENT_DATA (1 << 2)
|
|
|
|
/* Normal TRB fields */
|
|
/* transfer_len bitmasks - bits 0:16 */
|
|
#define TRB_LEN(p) ((p) & 0x1ffff)
|
|
/* TD Size, packets remaining in this TD, bits 21:17 (5 bits, so max 31) */
|
|
#define TRB_TD_SIZE(p) (min((p), (u32)31) << 17)
|
|
#define GET_TD_SIZE(p) (((p) & 0x3e0000) >> 17)
|
|
/* xhci 1.1 uses the TD_SIZE field for TBC if Extended TBC is enabled (ETE) */
|
|
#define TRB_TD_SIZE_TBC(p) (min((p), (u32)31) << 17)
|
|
/* Interrupter Target - which MSI-X vector to target the completion event at */
|
|
#define TRB_INTR_TARGET(p) (((p) & 0x3ff) << 22)
|
|
#define GET_INTR_TARGET(p) (((p) >> 22) & 0x3ff)
|
|
/* Total burst count field, Rsvdz on xhci 1.1 with Extended TBC enabled (ETE) */
|
|
#define TRB_TBC(p) (((p) & 0x3) << 7)
|
|
#define TRB_TLBPC(p) (((p) & 0xf) << 16)
|
|
|
|
/* Cycle bit - indicates TRB ownership by HC or HCD */
|
|
#define TRB_CYCLE (1<<0)
|
|
/*
|
|
* Force next event data TRB to be evaluated before task switch.
|
|
* Used to pass OS data back after a TD completes.
|
|
*/
|
|
#define TRB_ENT (1<<1)
|
|
/* Interrupt on short packet */
|
|
#define TRB_ISP (1<<2)
|
|
/* Set PCIe no snoop attribute */
|
|
#define TRB_NO_SNOOP (1<<3)
|
|
/* Chain multiple TRBs into a TD */
|
|
#define TRB_CHAIN (1<<4)
|
|
/* Interrupt on completion */
|
|
#define TRB_IOC (1<<5)
|
|
/* The buffer pointer contains immediate data */
|
|
#define TRB_IDT (1<<6)
|
|
/* TDs smaller than this might use IDT */
|
|
#define TRB_IDT_MAX_SIZE 8
|
|
|
|
/* Block Event Interrupt */
|
|
#define TRB_BEI (1<<9)
|
|
|
|
/* Control transfer TRB specific fields */
|
|
#define TRB_DIR_IN (1<<16)
|
|
#define TRB_TX_TYPE(p) ((p) << 16)
|
|
#define TRB_DATA_OUT 2
|
|
#define TRB_DATA_IN 3
|
|
|
|
/* Isochronous TRB specific fields */
|
|
#define TRB_SIA (1<<31)
|
|
#define TRB_FRAME_ID(p) (((p) & 0x7ff) << 20)
|
|
|
|
/* TRB cache size for xHC with TRB cache */
|
|
#define TRB_CACHE_SIZE_HS 8
|
|
#define TRB_CACHE_SIZE_SS 16
|
|
|
|
struct xhci_generic_trb {
|
|
__le32 field[4];
|
|
};
|
|
|
|
union xhci_trb {
|
|
struct xhci_link_trb link;
|
|
struct xhci_transfer_event trans_event;
|
|
struct xhci_event_cmd event_cmd;
|
|
struct xhci_generic_trb generic;
|
|
};
|
|
|
|
/* TRB bit mask */
|
|
#define TRB_TYPE_BITMASK (0xfc00)
|
|
#define TRB_TYPE(p) ((p) << 10)
|
|
#define TRB_FIELD_TO_TYPE(p) (((p) & TRB_TYPE_BITMASK) >> 10)
|
|
/* TRB type IDs */
|
|
/* bulk, interrupt, isoc scatter/gather, and control data stage */
|
|
#define TRB_NORMAL 1
|
|
/* setup stage for control transfers */
|
|
#define TRB_SETUP 2
|
|
/* data stage for control transfers */
|
|
#define TRB_DATA 3
|
|
/* status stage for control transfers */
|
|
#define TRB_STATUS 4
|
|
/* isoc transfers */
|
|
#define TRB_ISOC 5
|
|
/* TRB for linking ring segments */
|
|
#define TRB_LINK 6
|
|
#define TRB_EVENT_DATA 7
|
|
/* Transfer Ring No-op (not for the command ring) */
|
|
#define TRB_TR_NOOP 8
|
|
/* Command TRBs */
|
|
/* Enable Slot Command */
|
|
#define TRB_ENABLE_SLOT 9
|
|
/* Disable Slot Command */
|
|
#define TRB_DISABLE_SLOT 10
|
|
/* Address Device Command */
|
|
#define TRB_ADDR_DEV 11
|
|
/* Configure Endpoint Command */
|
|
#define TRB_CONFIG_EP 12
|
|
/* Evaluate Context Command */
|
|
#define TRB_EVAL_CONTEXT 13
|
|
/* Reset Endpoint Command */
|
|
#define TRB_RESET_EP 14
|
|
/* Stop Transfer Ring Command */
|
|
#define TRB_STOP_RING 15
|
|
/* Set Transfer Ring Dequeue Pointer Command */
|
|
#define TRB_SET_DEQ 16
|
|
/* Reset Device Command */
|
|
#define TRB_RESET_DEV 17
|
|
/* Force Event Command (opt) */
|
|
#define TRB_FORCE_EVENT 18
|
|
/* Negotiate Bandwidth Command (opt) */
|
|
#define TRB_NEG_BANDWIDTH 19
|
|
/* Set Latency Tolerance Value Command (opt) */
|
|
#define TRB_SET_LT 20
|
|
/* Get port bandwidth Command */
|
|
#define TRB_GET_BW 21
|
|
/* Force Header Command - generate a transaction or link management packet */
|
|
#define TRB_FORCE_HEADER 22
|
|
/* No-op Command - not for transfer rings */
|
|
#define TRB_CMD_NOOP 23
|
|
/* TRB IDs 24-31 reserved */
|
|
/* Event TRBS */
|
|
/* Transfer Event */
|
|
#define TRB_TRANSFER 32
|
|
/* Command Completion Event */
|
|
#define TRB_COMPLETION 33
|
|
/* Port Status Change Event */
|
|
#define TRB_PORT_STATUS 34
|
|
/* Bandwidth Request Event (opt) */
|
|
#define TRB_BANDWIDTH_EVENT 35
|
|
/* Doorbell Event (opt) */
|
|
#define TRB_DOORBELL 36
|
|
/* Host Controller Event */
|
|
#define TRB_HC_EVENT 37
|
|
/* Device Notification Event - device sent function wake notification */
|
|
#define TRB_DEV_NOTE 38
|
|
/* MFINDEX Wrap Event - microframe counter wrapped */
|
|
#define TRB_MFINDEX_WRAP 39
|
|
/* TRB IDs 40-47 reserved, 48-63 is vendor-defined */
|
|
#define TRB_VENDOR_DEFINED_LOW 48
|
|
/* Nec vendor-specific command completion event. */
|
|
#define TRB_NEC_CMD_COMP 48
|
|
/* Get NEC firmware revision. */
|
|
#define TRB_NEC_GET_FW 49
|
|
|
|
static inline const char *xhci_trb_type_string(u8 type)
|
|
{
|
|
switch (type) {
|
|
case TRB_NORMAL:
|
|
return "Normal";
|
|
case TRB_SETUP:
|
|
return "Setup Stage";
|
|
case TRB_DATA:
|
|
return "Data Stage";
|
|
case TRB_STATUS:
|
|
return "Status Stage";
|
|
case TRB_ISOC:
|
|
return "Isoch";
|
|
case TRB_LINK:
|
|
return "Link";
|
|
case TRB_EVENT_DATA:
|
|
return "Event Data";
|
|
case TRB_TR_NOOP:
|
|
return "No-Op";
|
|
case TRB_ENABLE_SLOT:
|
|
return "Enable Slot Command";
|
|
case TRB_DISABLE_SLOT:
|
|
return "Disable Slot Command";
|
|
case TRB_ADDR_DEV:
|
|
return "Address Device Command";
|
|
case TRB_CONFIG_EP:
|
|
return "Configure Endpoint Command";
|
|
case TRB_EVAL_CONTEXT:
|
|
return "Evaluate Context Command";
|
|
case TRB_RESET_EP:
|
|
return "Reset Endpoint Command";
|
|
case TRB_STOP_RING:
|
|
return "Stop Ring Command";
|
|
case TRB_SET_DEQ:
|
|
return "Set TR Dequeue Pointer Command";
|
|
case TRB_RESET_DEV:
|
|
return "Reset Device Command";
|
|
case TRB_FORCE_EVENT:
|
|
return "Force Event Command";
|
|
case TRB_NEG_BANDWIDTH:
|
|
return "Negotiate Bandwidth Command";
|
|
case TRB_SET_LT:
|
|
return "Set Latency Tolerance Value Command";
|
|
case TRB_GET_BW:
|
|
return "Get Port Bandwidth Command";
|
|
case TRB_FORCE_HEADER:
|
|
return "Force Header Command";
|
|
case TRB_CMD_NOOP:
|
|
return "No-Op Command";
|
|
case TRB_TRANSFER:
|
|
return "Transfer Event";
|
|
case TRB_COMPLETION:
|
|
return "Command Completion Event";
|
|
case TRB_PORT_STATUS:
|
|
return "Port Status Change Event";
|
|
case TRB_BANDWIDTH_EVENT:
|
|
return "Bandwidth Request Event";
|
|
case TRB_DOORBELL:
|
|
return "Doorbell Event";
|
|
case TRB_HC_EVENT:
|
|
return "Host Controller Event";
|
|
case TRB_DEV_NOTE:
|
|
return "Device Notification Event";
|
|
case TRB_MFINDEX_WRAP:
|
|
return "MFINDEX Wrap Event";
|
|
case TRB_NEC_CMD_COMP:
|
|
return "NEC Command Completion Event";
|
|
case TRB_NEC_GET_FW:
|
|
return "NET Get Firmware Revision Command";
|
|
default:
|
|
return "UNKNOWN";
|
|
}
|
|
}
|
|
|
|
#define TRB_TYPE_LINK(x) (((x) & TRB_TYPE_BITMASK) == TRB_TYPE(TRB_LINK))
|
|
/* Above, but for __le32 types -- can avoid work by swapping constants: */
|
|
#define TRB_TYPE_LINK_LE32(x) (((x) & cpu_to_le32(TRB_TYPE_BITMASK)) == \
|
|
cpu_to_le32(TRB_TYPE(TRB_LINK)))
|
|
#define TRB_TYPE_NOOP_LE32(x) (((x) & cpu_to_le32(TRB_TYPE_BITMASK)) == \
|
|
cpu_to_le32(TRB_TYPE(TRB_TR_NOOP)))
|
|
|
|
#define NEC_FW_MINOR(p) (((p) >> 0) & 0xff)
|
|
#define NEC_FW_MAJOR(p) (((p) >> 8) & 0xff)
|
|
|
|
/*
|
|
* TRBS_PER_SEGMENT must be a multiple of 4,
|
|
* since the command ring is 64-byte aligned.
|
|
* It must also be greater than 16.
|
|
*/
|
|
#define TRBS_PER_SEGMENT 256
|
|
/* Allow two commands + a link TRB, along with any reserved command TRBs */
|
|
#define MAX_RSVD_CMD_TRBS (TRBS_PER_SEGMENT - 3)
|
|
#define TRB_SEGMENT_SIZE (TRBS_PER_SEGMENT*16)
|
|
#define TRB_SEGMENT_SHIFT (ilog2(TRB_SEGMENT_SIZE))
|
|
/* TRB buffer pointers can't cross 64KB boundaries */
|
|
#define TRB_MAX_BUFF_SHIFT 16
|
|
#define TRB_MAX_BUFF_SIZE (1 << TRB_MAX_BUFF_SHIFT)
|
|
/* How much data is left before the 64KB boundary? */
|
|
#define TRB_BUFF_LEN_UP_TO_BOUNDARY(addr) (TRB_MAX_BUFF_SIZE - \
|
|
(addr & (TRB_MAX_BUFF_SIZE - 1)))
|
|
#define MAX_SOFT_RETRY 3
|
|
/*
|
|
* Limits of consecutive isoc trbs that can Block Event Interrupt (BEI) if
|
|
* XHCI_AVOID_BEI quirk is in use.
|
|
*/
|
|
#define AVOID_BEI_INTERVAL_MIN 8
|
|
#define AVOID_BEI_INTERVAL_MAX 32
|
|
|
|
struct xhci_segment {
|
|
union xhci_trb *trbs;
|
|
/* private to HCD */
|
|
struct xhci_segment *next;
|
|
dma_addr_t dma;
|
|
/* Max packet sized bounce buffer for td-fragmant alignment */
|
|
dma_addr_t bounce_dma;
|
|
void *bounce_buf;
|
|
unsigned int bounce_offs;
|
|
unsigned int bounce_len;
|
|
};
|
|
|
|
enum xhci_cancelled_td_status {
|
|
TD_DIRTY = 0,
|
|
TD_HALTED,
|
|
TD_CLEARING_CACHE,
|
|
TD_CLEARED,
|
|
};
|
|
|
|
struct xhci_td {
|
|
struct list_head td_list;
|
|
struct list_head cancelled_td_list;
|
|
int status;
|
|
enum xhci_cancelled_td_status cancel_status;
|
|
struct urb *urb;
|
|
struct xhci_segment *start_seg;
|
|
union xhci_trb *first_trb;
|
|
union xhci_trb *last_trb;
|
|
struct xhci_segment *last_trb_seg;
|
|
struct xhci_segment *bounce_seg;
|
|
/* actual_length of the URB has already been set */
|
|
bool urb_length_set;
|
|
unsigned int num_trbs;
|
|
};
|
|
|
|
/* xHCI command default timeout value */
|
|
#define XHCI_CMD_DEFAULT_TIMEOUT (5 * HZ)
|
|
|
|
/* command descriptor */
|
|
struct xhci_cd {
|
|
struct xhci_command *command;
|
|
union xhci_trb *cmd_trb;
|
|
};
|
|
|
|
enum xhci_ring_type {
|
|
TYPE_CTRL = 0,
|
|
TYPE_ISOC,
|
|
TYPE_BULK,
|
|
TYPE_INTR,
|
|
TYPE_STREAM,
|
|
TYPE_COMMAND,
|
|
TYPE_EVENT,
|
|
};
|
|
|
|
static inline const char *xhci_ring_type_string(enum xhci_ring_type type)
|
|
{
|
|
switch (type) {
|
|
case TYPE_CTRL:
|
|
return "CTRL";
|
|
case TYPE_ISOC:
|
|
return "ISOC";
|
|
case TYPE_BULK:
|
|
return "BULK";
|
|
case TYPE_INTR:
|
|
return "INTR";
|
|
case TYPE_STREAM:
|
|
return "STREAM";
|
|
case TYPE_COMMAND:
|
|
return "CMD";
|
|
case TYPE_EVENT:
|
|
return "EVENT";
|
|
}
|
|
|
|
return "UNKNOWN";
|
|
}
|
|
|
|
struct xhci_ring {
|
|
struct xhci_segment *first_seg;
|
|
struct xhci_segment *last_seg;
|
|
union xhci_trb *enqueue;
|
|
struct xhci_segment *enq_seg;
|
|
union xhci_trb *dequeue;
|
|
struct xhci_segment *deq_seg;
|
|
struct list_head td_list;
|
|
/*
|
|
* Write the cycle state into the TRB cycle field to give ownership of
|
|
* the TRB to the host controller (if we are the producer), or to check
|
|
* if we own the TRB (if we are the consumer). See section 4.9.1.
|
|
*/
|
|
u32 cycle_state;
|
|
unsigned int err_count;
|
|
unsigned int stream_id;
|
|
unsigned int num_segs;
|
|
unsigned int num_trbs_free;
|
|
unsigned int num_trbs_free_temp;
|
|
unsigned int bounce_buf_len;
|
|
enum xhci_ring_type type;
|
|
bool last_td_was_short;
|
|
struct radix_tree_root *trb_address_map;
|
|
};
|
|
|
|
struct xhci_erst_entry {
|
|
/* 64-bit event ring segment address */
|
|
__le64 seg_addr;
|
|
__le32 seg_size;
|
|
/* Set to zero */
|
|
__le32 rsvd;
|
|
};
|
|
|
|
struct xhci_erst {
|
|
struct xhci_erst_entry *entries;
|
|
unsigned int num_entries;
|
|
/* xhci->event_ring keeps track of segment dma addresses */
|
|
dma_addr_t erst_dma_addr;
|
|
/* Num entries the ERST can contain */
|
|
unsigned int erst_size;
|
|
};
|
|
|
|
struct xhci_scratchpad {
|
|
u64 *sp_array;
|
|
dma_addr_t sp_dma;
|
|
void **sp_buffers;
|
|
};
|
|
|
|
struct urb_priv {
|
|
int num_tds;
|
|
int num_tds_done;
|
|
struct xhci_td td[];
|
|
};
|
|
|
|
/*
|
|
* Each segment table entry is 4*32bits long. 1K seems like an ok size:
|
|
* (1K bytes * 8bytes/bit) / (4*32 bits) = 64 segment entries in the table,
|
|
* meaning 64 ring segments.
|
|
* Initial allocated size of the ERST, in number of entries */
|
|
#define ERST_NUM_SEGS 1
|
|
/* Poll every 60 seconds */
|
|
#define POLL_TIMEOUT 60
|
|
/* Stop endpoint command timeout (secs) for URB cancellation watchdog timer */
|
|
#define XHCI_STOP_EP_CMD_TIMEOUT 5
|
|
/* XXX: Make these module parameters */
|
|
|
|
struct s3_save {
|
|
u32 command;
|
|
u32 dev_nt;
|
|
u64 dcbaa_ptr;
|
|
u32 config_reg;
|
|
u32 irq_pending;
|
|
u32 irq_control;
|
|
u32 erst_size;
|
|
u64 erst_base;
|
|
u64 erst_dequeue;
|
|
};
|
|
|
|
/* Use for lpm */
|
|
struct dev_info {
|
|
u32 dev_id;
|
|
struct list_head list;
|
|
};
|
|
|
|
struct xhci_bus_state {
|
|
unsigned long bus_suspended;
|
|
unsigned long next_statechange;
|
|
|
|
/* Port suspend arrays are indexed by the portnum of the fake roothub */
|
|
/* ports suspend status arrays - max 31 ports for USB2, 15 for USB3 */
|
|
u32 port_c_suspend;
|
|
u32 suspended_ports;
|
|
u32 port_remote_wakeup;
|
|
unsigned long resume_done[USB_MAXCHILDREN];
|
|
/* which ports have started to resume */
|
|
unsigned long resuming_ports;
|
|
/* Which ports are waiting on RExit to U0 transition. */
|
|
unsigned long rexit_ports;
|
|
struct completion rexit_done[USB_MAXCHILDREN];
|
|
struct completion u3exit_done[USB_MAXCHILDREN];
|
|
};
|
|
|
|
|
|
/*
|
|
* It can take up to 20 ms to transition from RExit to U0 on the
|
|
* Intel Lynx Point LP xHCI host.
|
|
*/
|
|
#define XHCI_MAX_REXIT_TIMEOUT_MS 20
|
|
struct xhci_port_cap {
|
|
u32 *psi; /* array of protocol speed ID entries */
|
|
u8 psi_count;
|
|
u8 psi_uid_count;
|
|
u8 maj_rev;
|
|
u8 min_rev;
|
|
};
|
|
|
|
struct xhci_port {
|
|
__le32 __iomem *addr;
|
|
int hw_portnum;
|
|
int hcd_portnum;
|
|
struct xhci_hub *rhub;
|
|
struct xhci_port_cap *port_cap;
|
|
};
|
|
|
|
struct xhci_hub {
|
|
struct xhci_port **ports;
|
|
unsigned int num_ports;
|
|
struct usb_hcd *hcd;
|
|
/* keep track of bus suspend info */
|
|
struct xhci_bus_state bus_state;
|
|
/* supported prococol extended capabiliy values */
|
|
u8 maj_rev;
|
|
u8 min_rev;
|
|
};
|
|
|
|
/* There is one xhci_hcd structure per controller */
|
|
struct xhci_hcd {
|
|
struct usb_hcd *main_hcd;
|
|
struct usb_hcd *shared_hcd;
|
|
/* glue to PCI and HCD framework */
|
|
struct xhci_cap_regs __iomem *cap_regs;
|
|
struct xhci_op_regs __iomem *op_regs;
|
|
struct xhci_run_regs __iomem *run_regs;
|
|
struct xhci_doorbell_array __iomem *dba;
|
|
/* Our HCD's current interrupter register set */
|
|
struct xhci_intr_reg __iomem *ir_set;
|
|
|
|
/* Cached register copies of read-only HC data */
|
|
__u32 hcs_params1;
|
|
__u32 hcs_params2;
|
|
__u32 hcs_params3;
|
|
__u32 hcc_params;
|
|
__u32 hcc_params2;
|
|
|
|
spinlock_t lock;
|
|
|
|
/* packed release number */
|
|
u8 sbrn;
|
|
u16 hci_version;
|
|
u8 max_slots;
|
|
u8 max_interrupters;
|
|
u8 max_ports;
|
|
u8 isoc_threshold;
|
|
/* imod_interval in ns (I * 250ns) */
|
|
u32 imod_interval;
|
|
u32 isoc_bei_interval;
|
|
int event_ring_max;
|
|
/* 4KB min, 128MB max */
|
|
int page_size;
|
|
/* Valid values are 12 to 20, inclusive */
|
|
int page_shift;
|
|
/* msi-x vectors */
|
|
int msix_count;
|
|
/* optional clocks */
|
|
struct clk *clk;
|
|
struct clk *reg_clk;
|
|
/* optional reset controller */
|
|
struct reset_control *reset;
|
|
/* data structures */
|
|
struct xhci_device_context_array *dcbaa;
|
|
struct xhci_ring *cmd_ring;
|
|
unsigned int cmd_ring_state;
|
|
#define CMD_RING_STATE_RUNNING (1 << 0)
|
|
#define CMD_RING_STATE_ABORTED (1 << 1)
|
|
#define CMD_RING_STATE_STOPPED (1 << 2)
|
|
struct list_head cmd_list;
|
|
unsigned int cmd_ring_reserved_trbs;
|
|
struct delayed_work cmd_timer;
|
|
struct completion cmd_ring_stop_completion;
|
|
struct xhci_command *current_cmd;
|
|
struct xhci_ring *event_ring;
|
|
struct xhci_erst erst;
|
|
/* Scratchpad */
|
|
struct xhci_scratchpad *scratchpad;
|
|
/* Store LPM test failed devices' information */
|
|
struct list_head lpm_failed_devs;
|
|
|
|
/* slot enabling and address device helpers */
|
|
/* these are not thread safe so use mutex */
|
|
struct mutex mutex;
|
|
/* For USB 3.0 LPM enable/disable. */
|
|
struct xhci_command *lpm_command;
|
|
/* Internal mirror of the HW's dcbaa */
|
|
struct xhci_virt_device *devs[MAX_HC_SLOTS];
|
|
/* For keeping track of bandwidth domains per roothub. */
|
|
struct xhci_root_port_bw_info *rh_bw;
|
|
|
|
/* DMA pools */
|
|
struct dma_pool *device_pool;
|
|
struct dma_pool *segment_pool;
|
|
struct dma_pool *small_streams_pool;
|
|
struct dma_pool *medium_streams_pool;
|
|
|
|
/* Host controller watchdog timer structures */
|
|
unsigned int xhc_state;
|
|
|
|
u32 command;
|
|
struct s3_save s3;
|
|
/* Host controller is dying - not responding to commands. "I'm not dead yet!"
|
|
*
|
|
* xHC interrupts have been disabled and a watchdog timer will (or has already)
|
|
* halt the xHCI host, and complete all URBs with an -ESHUTDOWN code. Any code
|
|
* that sees this status (other than the timer that set it) should stop touching
|
|
* hardware immediately. Interrupt handlers should return immediately when
|
|
* they see this status (any time they drop and re-acquire xhci->lock).
|
|
* xhci_urb_dequeue() should call usb_hcd_check_unlink_urb() and return without
|
|
* putting the TD on the canceled list, etc.
|
|
*
|
|
* There are no reports of xHCI host controllers that display this issue.
|
|
*/
|
|
#define XHCI_STATE_DYING (1 << 0)
|
|
#define XHCI_STATE_HALTED (1 << 1)
|
|
#define XHCI_STATE_REMOVING (1 << 2)
|
|
unsigned long long quirks;
|
|
#define XHCI_LINK_TRB_QUIRK BIT_ULL(0)
|
|
#define XHCI_RESET_EP_QUIRK BIT_ULL(1)
|
|
#define XHCI_NEC_HOST BIT_ULL(2)
|
|
#define XHCI_AMD_PLL_FIX BIT_ULL(3)
|
|
#define XHCI_SPURIOUS_SUCCESS BIT_ULL(4)
|
|
/*
|
|
* Certain Intel host controllers have a limit to the number of endpoint
|
|
* contexts they can handle. Ideally, they would signal that they can't handle
|
|
* anymore endpoint contexts by returning a Resource Error for the Configure
|
|
* Endpoint command, but they don't. Instead they expect software to keep track
|
|
* of the number of active endpoints for them, across configure endpoint
|
|
* commands, reset device commands, disable slot commands, and address device
|
|
* commands.
|
|
*/
|
|
#define XHCI_EP_LIMIT_QUIRK BIT_ULL(5)
|
|
#define XHCI_BROKEN_MSI BIT_ULL(6)
|
|
#define XHCI_RESET_ON_RESUME BIT_ULL(7)
|
|
#define XHCI_SW_BW_CHECKING BIT_ULL(8)
|
|
#define XHCI_AMD_0x96_HOST BIT_ULL(9)
|
|
#define XHCI_TRUST_TX_LENGTH BIT_ULL(10)
|
|
#define XHCI_LPM_SUPPORT BIT_ULL(11)
|
|
#define XHCI_INTEL_HOST BIT_ULL(12)
|
|
#define XHCI_SPURIOUS_REBOOT BIT_ULL(13)
|
|
#define XHCI_COMP_MODE_QUIRK BIT_ULL(14)
|
|
#define XHCI_AVOID_BEI BIT_ULL(15)
|
|
#define XHCI_PLAT BIT_ULL(16)
|
|
#define XHCI_SLOW_SUSPEND BIT_ULL(17)
|
|
#define XHCI_SPURIOUS_WAKEUP BIT_ULL(18)
|
|
/* For controllers with a broken beyond repair streams implementation */
|
|
#define XHCI_BROKEN_STREAMS BIT_ULL(19)
|
|
#define XHCI_PME_STUCK_QUIRK BIT_ULL(20)
|
|
#define XHCI_MTK_HOST BIT_ULL(21)
|
|
#define XHCI_SSIC_PORT_UNUSED BIT_ULL(22)
|
|
#define XHCI_NO_64BIT_SUPPORT BIT_ULL(23)
|
|
#define XHCI_MISSING_CAS BIT_ULL(24)
|
|
/* For controller with a broken Port Disable implementation */
|
|
#define XHCI_BROKEN_PORT_PED BIT_ULL(25)
|
|
#define XHCI_LIMIT_ENDPOINT_INTERVAL_7 BIT_ULL(26)
|
|
#define XHCI_U2_DISABLE_WAKE BIT_ULL(27)
|
|
#define XHCI_ASMEDIA_MODIFY_FLOWCONTROL BIT_ULL(28)
|
|
#define XHCI_HW_LPM_DISABLE BIT_ULL(29)
|
|
#define XHCI_SUSPEND_DELAY BIT_ULL(30)
|
|
#define XHCI_INTEL_USB_ROLE_SW BIT_ULL(31)
|
|
#define XHCI_ZERO_64B_REGS BIT_ULL(32)
|
|
#define XHCI_DEFAULT_PM_RUNTIME_ALLOW BIT_ULL(33)
|
|
#define XHCI_RESET_PLL_ON_DISCONNECT BIT_ULL(34)
|
|
#define XHCI_SNPS_BROKEN_SUSPEND BIT_ULL(35)
|
|
#define XHCI_RENESAS_FW_QUIRK BIT_ULL(36)
|
|
#define XHCI_SKIP_PHY_INIT BIT_ULL(37)
|
|
#define XHCI_DISABLE_SPARSE BIT_ULL(38)
|
|
#define XHCI_SG_TRB_CACHE_SIZE_QUIRK BIT_ULL(39)
|
|
#define XHCI_NO_SOFT_RETRY BIT_ULL(40)
|
|
#define XHCI_BROKEN_D3COLD BIT_ULL(41)
|
|
#define XHCI_EP_CTX_BROKEN_DCS BIT_ULL(42)
|
|
|
|
unsigned int num_active_eps;
|
|
unsigned int limit_active_eps;
|
|
struct xhci_port *hw_ports;
|
|
struct xhci_hub usb2_rhub;
|
|
struct xhci_hub usb3_rhub;
|
|
/* support xHCI 1.0 spec USB2 hardware LPM */
|
|
unsigned hw_lpm_support:1;
|
|
/* Broken Suspend flag for SNPS Suspend resume issue */
|
|
unsigned broken_suspend:1;
|
|
/* cached usb2 extened protocol capabilites */
|
|
u32 *ext_caps;
|
|
unsigned int num_ext_caps;
|
|
/* cached extended protocol port capabilities */
|
|
struct xhci_port_cap *port_caps;
|
|
unsigned int num_port_caps;
|
|
/* Compliance Mode Recovery Data */
|
|
struct timer_list comp_mode_recovery_timer;
|
|
u32 port_status_u0;
|
|
u16 test_mode;
|
|
/* Compliance Mode Timer Triggered every 2 seconds */
|
|
#define COMP_MODE_RCVRY_MSECS 2000
|
|
|
|
struct dentry *debugfs_root;
|
|
struct dentry *debugfs_slots;
|
|
struct list_head regset_list;
|
|
|
|
void *dbc;
|
|
/* platform-specific data -- must come last */
|
|
unsigned long priv[] __aligned(sizeof(s64));
|
|
};
|
|
|
|
/* Platform specific overrides to generic XHCI hc_driver ops */
|
|
struct xhci_driver_overrides {
|
|
size_t extra_priv_size;
|
|
int (*reset)(struct usb_hcd *hcd);
|
|
int (*start)(struct usb_hcd *hcd);
|
|
int (*add_endpoint)(struct usb_hcd *hcd, struct usb_device *udev,
|
|
struct usb_host_endpoint *ep);
|
|
int (*drop_endpoint)(struct usb_hcd *hcd, struct usb_device *udev,
|
|
struct usb_host_endpoint *ep);
|
|
int (*check_bandwidth)(struct usb_hcd *, struct usb_device *);
|
|
void (*reset_bandwidth)(struct usb_hcd *, struct usb_device *);
|
|
};
|
|
|
|
#define XHCI_CFC_DELAY 10
|
|
|
|
/* convert between an HCD pointer and the corresponding EHCI_HCD */
|
|
static inline struct xhci_hcd *hcd_to_xhci(struct usb_hcd *hcd)
|
|
{
|
|
struct usb_hcd *primary_hcd;
|
|
|
|
if (usb_hcd_is_primary_hcd(hcd))
|
|
primary_hcd = hcd;
|
|
else
|
|
primary_hcd = hcd->primary_hcd;
|
|
|
|
return (struct xhci_hcd *) (primary_hcd->hcd_priv);
|
|
}
|
|
|
|
static inline struct usb_hcd *xhci_to_hcd(struct xhci_hcd *xhci)
|
|
{
|
|
return xhci->main_hcd;
|
|
}
|
|
|
|
#define xhci_dbg(xhci, fmt, args...) \
|
|
dev_dbg(xhci_to_hcd(xhci)->self.controller , fmt , ## args)
|
|
#define xhci_err(xhci, fmt, args...) \
|
|
dev_err(xhci_to_hcd(xhci)->self.controller , fmt , ## args)
|
|
#define xhci_warn(xhci, fmt, args...) \
|
|
dev_warn(xhci_to_hcd(xhci)->self.controller , fmt , ## args)
|
|
#define xhci_warn_ratelimited(xhci, fmt, args...) \
|
|
dev_warn_ratelimited(xhci_to_hcd(xhci)->self.controller , fmt , ## args)
|
|
#define xhci_info(xhci, fmt, args...) \
|
|
dev_info(xhci_to_hcd(xhci)->self.controller , fmt , ## args)
|
|
|
|
/*
|
|
* Registers should always be accessed with double word or quad word accesses.
|
|
*
|
|
* Some xHCI implementations may support 64-bit address pointers. Registers
|
|
* with 64-bit address pointers should be written to with dword accesses by
|
|
* writing the low dword first (ptr[0]), then the high dword (ptr[1]) second.
|
|
* xHCI implementations that do not support 64-bit address pointers will ignore
|
|
* the high dword, and write order is irrelevant.
|
|
*/
|
|
static inline u64 xhci_read_64(const struct xhci_hcd *xhci,
|
|
__le64 __iomem *regs)
|
|
{
|
|
return lo_hi_readq(regs);
|
|
}
|
|
static inline void xhci_write_64(struct xhci_hcd *xhci,
|
|
const u64 val, __le64 __iomem *regs)
|
|
{
|
|
lo_hi_writeq(val, regs);
|
|
}
|
|
|
|
static inline int xhci_link_trb_quirk(struct xhci_hcd *xhci)
|
|
{
|
|
return xhci->quirks & XHCI_LINK_TRB_QUIRK;
|
|
}
|
|
|
|
/* xHCI debugging */
|
|
char *xhci_get_slot_state(struct xhci_hcd *xhci,
|
|
struct xhci_container_ctx *ctx);
|
|
void xhci_dbg_trace(struct xhci_hcd *xhci, void (*trace)(struct va_format *),
|
|
const char *fmt, ...);
|
|
|
|
/* xHCI memory management */
|
|
void xhci_mem_cleanup(struct xhci_hcd *xhci);
|
|
int xhci_mem_init(struct xhci_hcd *xhci, gfp_t flags);
|
|
void xhci_free_virt_device(struct xhci_hcd *xhci, int slot_id);
|
|
int xhci_alloc_virt_device(struct xhci_hcd *xhci, int slot_id, struct usb_device *udev, gfp_t flags);
|
|
int xhci_setup_addressable_virt_dev(struct xhci_hcd *xhci, struct usb_device *udev);
|
|
void xhci_copy_ep0_dequeue_into_input_ctx(struct xhci_hcd *xhci,
|
|
struct usb_device *udev);
|
|
unsigned int xhci_get_endpoint_index(struct usb_endpoint_descriptor *desc);
|
|
unsigned int xhci_get_endpoint_address(unsigned int ep_index);
|
|
unsigned int xhci_last_valid_endpoint(u32 added_ctxs);
|
|
void xhci_endpoint_zero(struct xhci_hcd *xhci, struct xhci_virt_device *virt_dev, struct usb_host_endpoint *ep);
|
|
void xhci_update_tt_active_eps(struct xhci_hcd *xhci,
|
|
struct xhci_virt_device *virt_dev,
|
|
int old_active_eps);
|
|
void xhci_clear_endpoint_bw_info(struct xhci_bw_info *bw_info);
|
|
void xhci_update_bw_info(struct xhci_hcd *xhci,
|
|
struct xhci_container_ctx *in_ctx,
|
|
struct xhci_input_control_ctx *ctrl_ctx,
|
|
struct xhci_virt_device *virt_dev);
|
|
void xhci_endpoint_copy(struct xhci_hcd *xhci,
|
|
struct xhci_container_ctx *in_ctx,
|
|
struct xhci_container_ctx *out_ctx,
|
|
unsigned int ep_index);
|
|
void xhci_slot_copy(struct xhci_hcd *xhci,
|
|
struct xhci_container_ctx *in_ctx,
|
|
struct xhci_container_ctx *out_ctx);
|
|
int xhci_endpoint_init(struct xhci_hcd *xhci, struct xhci_virt_device *virt_dev,
|
|
struct usb_device *udev, struct usb_host_endpoint *ep,
|
|
gfp_t mem_flags);
|
|
struct xhci_ring *xhci_ring_alloc(struct xhci_hcd *xhci,
|
|
unsigned int num_segs, unsigned int cycle_state,
|
|
enum xhci_ring_type type, unsigned int max_packet, gfp_t flags);
|
|
void xhci_ring_free(struct xhci_hcd *xhci, struct xhci_ring *ring);
|
|
int xhci_ring_expansion(struct xhci_hcd *xhci, struct xhci_ring *ring,
|
|
unsigned int num_trbs, gfp_t flags);
|
|
int xhci_alloc_erst(struct xhci_hcd *xhci,
|
|
struct xhci_ring *evt_ring,
|
|
struct xhci_erst *erst,
|
|
gfp_t flags);
|
|
void xhci_initialize_ring_info(struct xhci_ring *ring,
|
|
unsigned int cycle_state);
|
|
void xhci_free_erst(struct xhci_hcd *xhci, struct xhci_erst *erst);
|
|
void xhci_free_endpoint_ring(struct xhci_hcd *xhci,
|
|
struct xhci_virt_device *virt_dev,
|
|
unsigned int ep_index);
|
|
struct xhci_stream_info *xhci_alloc_stream_info(struct xhci_hcd *xhci,
|
|
unsigned int num_stream_ctxs,
|
|
unsigned int num_streams,
|
|
unsigned int max_packet, gfp_t flags);
|
|
void xhci_free_stream_info(struct xhci_hcd *xhci,
|
|
struct xhci_stream_info *stream_info);
|
|
void xhci_setup_streams_ep_input_ctx(struct xhci_hcd *xhci,
|
|
struct xhci_ep_ctx *ep_ctx,
|
|
struct xhci_stream_info *stream_info);
|
|
void xhci_setup_no_streams_ep_input_ctx(struct xhci_ep_ctx *ep_ctx,
|
|
struct xhci_virt_ep *ep);
|
|
void xhci_free_device_endpoint_resources(struct xhci_hcd *xhci,
|
|
struct xhci_virt_device *virt_dev, bool drop_control_ep);
|
|
struct xhci_ring *xhci_dma_to_transfer_ring(
|
|
struct xhci_virt_ep *ep,
|
|
u64 address);
|
|
struct xhci_command *xhci_alloc_command(struct xhci_hcd *xhci,
|
|
bool allocate_completion, gfp_t mem_flags);
|
|
struct xhci_command *xhci_alloc_command_with_ctx(struct xhci_hcd *xhci,
|
|
bool allocate_completion, gfp_t mem_flags);
|
|
void xhci_urb_free_priv(struct urb_priv *urb_priv);
|
|
void xhci_free_command(struct xhci_hcd *xhci,
|
|
struct xhci_command *command);
|
|
struct xhci_container_ctx *xhci_alloc_container_ctx(struct xhci_hcd *xhci,
|
|
int type, gfp_t flags);
|
|
void xhci_free_container_ctx(struct xhci_hcd *xhci,
|
|
struct xhci_container_ctx *ctx);
|
|
|
|
/* xHCI host controller glue */
|
|
typedef void (*xhci_get_quirks_t)(struct device *, struct xhci_hcd *);
|
|
int xhci_handshake(void __iomem *ptr, u32 mask, u32 done, int usec);
|
|
void xhci_quiesce(struct xhci_hcd *xhci);
|
|
int xhci_halt(struct xhci_hcd *xhci);
|
|
int xhci_start(struct xhci_hcd *xhci);
|
|
int xhci_reset(struct xhci_hcd *xhci);
|
|
int xhci_run(struct usb_hcd *hcd);
|
|
int xhci_gen_setup(struct usb_hcd *hcd, xhci_get_quirks_t get_quirks);
|
|
void xhci_shutdown(struct usb_hcd *hcd);
|
|
void xhci_init_driver(struct hc_driver *drv,
|
|
const struct xhci_driver_overrides *over);
|
|
int xhci_add_endpoint(struct usb_hcd *hcd, struct usb_device *udev,
|
|
struct usb_host_endpoint *ep);
|
|
int xhci_drop_endpoint(struct usb_hcd *hcd, struct usb_device *udev,
|
|
struct usb_host_endpoint *ep);
|
|
int xhci_check_bandwidth(struct usb_hcd *hcd, struct usb_device *udev);
|
|
void xhci_reset_bandwidth(struct usb_hcd *hcd, struct usb_device *udev);
|
|
int xhci_disable_slot(struct xhci_hcd *xhci, u32 slot_id);
|
|
int xhci_ext_cap_init(struct xhci_hcd *xhci);
|
|
|
|
int xhci_suspend(struct xhci_hcd *xhci, bool do_wakeup);
|
|
int xhci_resume(struct xhci_hcd *xhci, bool hibernated);
|
|
|
|
irqreturn_t xhci_irq(struct usb_hcd *hcd);
|
|
irqreturn_t xhci_msi_irq(int irq, void *hcd);
|
|
int xhci_alloc_dev(struct usb_hcd *hcd, struct usb_device *udev);
|
|
int xhci_alloc_tt_info(struct xhci_hcd *xhci,
|
|
struct xhci_virt_device *virt_dev,
|
|
struct usb_device *hdev,
|
|
struct usb_tt *tt, gfp_t mem_flags);
|
|
|
|
/* xHCI ring, segment, TRB, and TD functions */
|
|
dma_addr_t xhci_trb_virt_to_dma(struct xhci_segment *seg, union xhci_trb *trb);
|
|
struct xhci_segment *trb_in_td(struct xhci_hcd *xhci,
|
|
struct xhci_segment *start_seg, union xhci_trb *start_trb,
|
|
union xhci_trb *end_trb, dma_addr_t suspect_dma, bool debug);
|
|
int xhci_is_vendor_info_code(struct xhci_hcd *xhci, unsigned int trb_comp_code);
|
|
void xhci_ring_cmd_db(struct xhci_hcd *xhci);
|
|
int xhci_queue_slot_control(struct xhci_hcd *xhci, struct xhci_command *cmd,
|
|
u32 trb_type, u32 slot_id);
|
|
int xhci_queue_address_device(struct xhci_hcd *xhci, struct xhci_command *cmd,
|
|
dma_addr_t in_ctx_ptr, u32 slot_id, enum xhci_setup_dev);
|
|
int xhci_queue_vendor_command(struct xhci_hcd *xhci, struct xhci_command *cmd,
|
|
u32 field1, u32 field2, u32 field3, u32 field4);
|
|
int xhci_queue_stop_endpoint(struct xhci_hcd *xhci, struct xhci_command *cmd,
|
|
int slot_id, unsigned int ep_index, int suspend);
|
|
int xhci_queue_ctrl_tx(struct xhci_hcd *xhci, gfp_t mem_flags, struct urb *urb,
|
|
int slot_id, unsigned int ep_index);
|
|
int xhci_queue_bulk_tx(struct xhci_hcd *xhci, gfp_t mem_flags, struct urb *urb,
|
|
int slot_id, unsigned int ep_index);
|
|
int xhci_queue_intr_tx(struct xhci_hcd *xhci, gfp_t mem_flags, struct urb *urb,
|
|
int slot_id, unsigned int ep_index);
|
|
int xhci_queue_isoc_tx_prepare(struct xhci_hcd *xhci, gfp_t mem_flags,
|
|
struct urb *urb, int slot_id, unsigned int ep_index);
|
|
int xhci_queue_configure_endpoint(struct xhci_hcd *xhci,
|
|
struct xhci_command *cmd, dma_addr_t in_ctx_ptr, u32 slot_id,
|
|
bool command_must_succeed);
|
|
int xhci_queue_evaluate_context(struct xhci_hcd *xhci, struct xhci_command *cmd,
|
|
dma_addr_t in_ctx_ptr, u32 slot_id, bool command_must_succeed);
|
|
int xhci_queue_reset_ep(struct xhci_hcd *xhci, struct xhci_command *cmd,
|
|
int slot_id, unsigned int ep_index,
|
|
enum xhci_ep_reset_type reset_type);
|
|
int xhci_queue_reset_device(struct xhci_hcd *xhci, struct xhci_command *cmd,
|
|
u32 slot_id);
|
|
void xhci_cleanup_stalled_ring(struct xhci_hcd *xhci, unsigned int slot_id,
|
|
unsigned int ep_index, unsigned int stream_id,
|
|
struct xhci_td *td);
|
|
void xhci_stop_endpoint_command_watchdog(struct timer_list *t);
|
|
void xhci_handle_command_timeout(struct work_struct *work);
|
|
|
|
void xhci_ring_ep_doorbell(struct xhci_hcd *xhci, unsigned int slot_id,
|
|
unsigned int ep_index, unsigned int stream_id);
|
|
void xhci_ring_doorbell_for_active_rings(struct xhci_hcd *xhci,
|
|
unsigned int slot_id,
|
|
unsigned int ep_index);
|
|
void xhci_cleanup_command_queue(struct xhci_hcd *xhci);
|
|
void inc_deq(struct xhci_hcd *xhci, struct xhci_ring *ring);
|
|
unsigned int count_trbs(u64 addr, u64 len);
|
|
|
|
/* xHCI roothub code */
|
|
void xhci_set_link_state(struct xhci_hcd *xhci, struct xhci_port *port,
|
|
u32 link_state);
|
|
void xhci_test_and_clear_bit(struct xhci_hcd *xhci, struct xhci_port *port,
|
|
u32 port_bit);
|
|
int xhci_hub_control(struct usb_hcd *hcd, u16 typeReq, u16 wValue, u16 wIndex,
|
|
char *buf, u16 wLength);
|
|
int xhci_hub_status_data(struct usb_hcd *hcd, char *buf);
|
|
int xhci_find_raw_port_number(struct usb_hcd *hcd, int port1);
|
|
struct xhci_hub *xhci_get_rhub(struct usb_hcd *hcd);
|
|
|
|
void xhci_hc_died(struct xhci_hcd *xhci);
|
|
|
|
#ifdef CONFIG_PM
|
|
int xhci_bus_suspend(struct usb_hcd *hcd);
|
|
int xhci_bus_resume(struct usb_hcd *hcd);
|
|
unsigned long xhci_get_resuming_ports(struct usb_hcd *hcd);
|
|
#else
|
|
#define xhci_bus_suspend NULL
|
|
#define xhci_bus_resume NULL
|
|
#define xhci_get_resuming_ports NULL
|
|
#endif /* CONFIG_PM */
|
|
|
|
u32 xhci_port_state_to_neutral(u32 state);
|
|
int xhci_find_slot_id_by_port(struct usb_hcd *hcd, struct xhci_hcd *xhci,
|
|
u16 port);
|
|
void xhci_ring_device(struct xhci_hcd *xhci, int slot_id);
|
|
|
|
/* xHCI contexts */
|
|
struct xhci_input_control_ctx *xhci_get_input_control_ctx(struct xhci_container_ctx *ctx);
|
|
struct xhci_slot_ctx *xhci_get_slot_ctx(struct xhci_hcd *xhci, struct xhci_container_ctx *ctx);
|
|
struct xhci_ep_ctx *xhci_get_ep_ctx(struct xhci_hcd *xhci, struct xhci_container_ctx *ctx, unsigned int ep_index);
|
|
|
|
struct xhci_ring *xhci_triad_to_transfer_ring(struct xhci_hcd *xhci,
|
|
unsigned int slot_id, unsigned int ep_index,
|
|
unsigned int stream_id);
|
|
|
|
static inline struct xhci_ring *xhci_urb_to_transfer_ring(struct xhci_hcd *xhci,
|
|
struct urb *urb)
|
|
{
|
|
return xhci_triad_to_transfer_ring(xhci, urb->dev->slot_id,
|
|
xhci_get_endpoint_index(&urb->ep->desc),
|
|
urb->stream_id);
|
|
}
|
|
|
|
/*
|
|
* TODO: As per spec Isochronous IDT transmissions are supported. We bypass
|
|
* them anyways as we where unable to find a device that matches the
|
|
* constraints.
|
|
*/
|
|
static inline bool xhci_urb_suitable_for_idt(struct urb *urb)
|
|
{
|
|
if (!usb_endpoint_xfer_isoc(&urb->ep->desc) && usb_urb_dir_out(urb) &&
|
|
usb_endpoint_maxp(&urb->ep->desc) >= TRB_IDT_MAX_SIZE &&
|
|
urb->transfer_buffer_length <= TRB_IDT_MAX_SIZE &&
|
|
!(urb->transfer_flags & URB_NO_TRANSFER_DMA_MAP) &&
|
|
!urb->num_sgs)
|
|
return true;
|
|
|
|
return false;
|
|
}
|
|
|
|
static inline char *xhci_slot_state_string(u32 state)
|
|
{
|
|
switch (state) {
|
|
case SLOT_STATE_ENABLED:
|
|
return "enabled/disabled";
|
|
case SLOT_STATE_DEFAULT:
|
|
return "default";
|
|
case SLOT_STATE_ADDRESSED:
|
|
return "addressed";
|
|
case SLOT_STATE_CONFIGURED:
|
|
return "configured";
|
|
default:
|
|
return "reserved";
|
|
}
|
|
}
|
|
|
|
static inline const char *xhci_decode_trb(char *str, size_t size,
|
|
u32 field0, u32 field1, u32 field2, u32 field3)
|
|
{
|
|
int type = TRB_FIELD_TO_TYPE(field3);
|
|
|
|
switch (type) {
|
|
case TRB_LINK:
|
|
snprintf(str, size,
|
|
"LINK %08x%08x intr %d type '%s' flags %c:%c:%c:%c",
|
|
field1, field0, GET_INTR_TARGET(field2),
|
|
xhci_trb_type_string(type),
|
|
field3 & TRB_IOC ? 'I' : 'i',
|
|
field3 & TRB_CHAIN ? 'C' : 'c',
|
|
field3 & TRB_TC ? 'T' : 't',
|
|
field3 & TRB_CYCLE ? 'C' : 'c');
|
|
break;
|
|
case TRB_TRANSFER:
|
|
case TRB_COMPLETION:
|
|
case TRB_PORT_STATUS:
|
|
case TRB_BANDWIDTH_EVENT:
|
|
case TRB_DOORBELL:
|
|
case TRB_HC_EVENT:
|
|
case TRB_DEV_NOTE:
|
|
case TRB_MFINDEX_WRAP:
|
|
snprintf(str, size,
|
|
"TRB %08x%08x status '%s' len %d slot %d ep %d type '%s' flags %c:%c",
|
|
field1, field0,
|
|
xhci_trb_comp_code_string(GET_COMP_CODE(field2)),
|
|
EVENT_TRB_LEN(field2), TRB_TO_SLOT_ID(field3),
|
|
/* Macro decrements 1, maybe it shouldn't?!? */
|
|
TRB_TO_EP_INDEX(field3) + 1,
|
|
xhci_trb_type_string(type),
|
|
field3 & EVENT_DATA ? 'E' : 'e',
|
|
field3 & TRB_CYCLE ? 'C' : 'c');
|
|
|
|
break;
|
|
case TRB_SETUP:
|
|
snprintf(str, size,
|
|
"bRequestType %02x bRequest %02x wValue %02x%02x wIndex %02x%02x wLength %d length %d TD size %d intr %d type '%s' flags %c:%c:%c",
|
|
field0 & 0xff,
|
|
(field0 & 0xff00) >> 8,
|
|
(field0 & 0xff000000) >> 24,
|
|
(field0 & 0xff0000) >> 16,
|
|
(field1 & 0xff00) >> 8,
|
|
field1 & 0xff,
|
|
(field1 & 0xff000000) >> 16 |
|
|
(field1 & 0xff0000) >> 16,
|
|
TRB_LEN(field2), GET_TD_SIZE(field2),
|
|
GET_INTR_TARGET(field2),
|
|
xhci_trb_type_string(type),
|
|
field3 & TRB_IDT ? 'I' : 'i',
|
|
field3 & TRB_IOC ? 'I' : 'i',
|
|
field3 & TRB_CYCLE ? 'C' : 'c');
|
|
break;
|
|
case TRB_DATA:
|
|
snprintf(str, size,
|
|
"Buffer %08x%08x length %d TD size %d intr %d type '%s' flags %c:%c:%c:%c:%c:%c:%c",
|
|
field1, field0, TRB_LEN(field2), GET_TD_SIZE(field2),
|
|
GET_INTR_TARGET(field2),
|
|
xhci_trb_type_string(type),
|
|
field3 & TRB_IDT ? 'I' : 'i',
|
|
field3 & TRB_IOC ? 'I' : 'i',
|
|
field3 & TRB_CHAIN ? 'C' : 'c',
|
|
field3 & TRB_NO_SNOOP ? 'S' : 's',
|
|
field3 & TRB_ISP ? 'I' : 'i',
|
|
field3 & TRB_ENT ? 'E' : 'e',
|
|
field3 & TRB_CYCLE ? 'C' : 'c');
|
|
break;
|
|
case TRB_STATUS:
|
|
snprintf(str, size,
|
|
"Buffer %08x%08x length %d TD size %d intr %d type '%s' flags %c:%c:%c:%c",
|
|
field1, field0, TRB_LEN(field2), GET_TD_SIZE(field2),
|
|
GET_INTR_TARGET(field2),
|
|
xhci_trb_type_string(type),
|
|
field3 & TRB_IOC ? 'I' : 'i',
|
|
field3 & TRB_CHAIN ? 'C' : 'c',
|
|
field3 & TRB_ENT ? 'E' : 'e',
|
|
field3 & TRB_CYCLE ? 'C' : 'c');
|
|
break;
|
|
case TRB_NORMAL:
|
|
case TRB_ISOC:
|
|
case TRB_EVENT_DATA:
|
|
case TRB_TR_NOOP:
|
|
snprintf(str, size,
|
|
"Buffer %08x%08x length %d TD size %d intr %d type '%s' flags %c:%c:%c:%c:%c:%c:%c:%c",
|
|
field1, field0, TRB_LEN(field2), GET_TD_SIZE(field2),
|
|
GET_INTR_TARGET(field2),
|
|
xhci_trb_type_string(type),
|
|
field3 & TRB_BEI ? 'B' : 'b',
|
|
field3 & TRB_IDT ? 'I' : 'i',
|
|
field3 & TRB_IOC ? 'I' : 'i',
|
|
field3 & TRB_CHAIN ? 'C' : 'c',
|
|
field3 & TRB_NO_SNOOP ? 'S' : 's',
|
|
field3 & TRB_ISP ? 'I' : 'i',
|
|
field3 & TRB_ENT ? 'E' : 'e',
|
|
field3 & TRB_CYCLE ? 'C' : 'c');
|
|
break;
|
|
|
|
case TRB_CMD_NOOP:
|
|
case TRB_ENABLE_SLOT:
|
|
snprintf(str, size,
|
|
"%s: flags %c",
|
|
xhci_trb_type_string(type),
|
|
field3 & TRB_CYCLE ? 'C' : 'c');
|
|
break;
|
|
case TRB_DISABLE_SLOT:
|
|
case TRB_NEG_BANDWIDTH:
|
|
snprintf(str, size,
|
|
"%s: slot %d flags %c",
|
|
xhci_trb_type_string(type),
|
|
TRB_TO_SLOT_ID(field3),
|
|
field3 & TRB_CYCLE ? 'C' : 'c');
|
|
break;
|
|
case TRB_ADDR_DEV:
|
|
snprintf(str, size,
|
|
"%s: ctx %08x%08x slot %d flags %c:%c",
|
|
xhci_trb_type_string(type),
|
|
field1, field0,
|
|
TRB_TO_SLOT_ID(field3),
|
|
field3 & TRB_BSR ? 'B' : 'b',
|
|
field3 & TRB_CYCLE ? 'C' : 'c');
|
|
break;
|
|
case TRB_CONFIG_EP:
|
|
snprintf(str, size,
|
|
"%s: ctx %08x%08x slot %d flags %c:%c",
|
|
xhci_trb_type_string(type),
|
|
field1, field0,
|
|
TRB_TO_SLOT_ID(field3),
|
|
field3 & TRB_DC ? 'D' : 'd',
|
|
field3 & TRB_CYCLE ? 'C' : 'c');
|
|
break;
|
|
case TRB_EVAL_CONTEXT:
|
|
snprintf(str, size,
|
|
"%s: ctx %08x%08x slot %d flags %c",
|
|
xhci_trb_type_string(type),
|
|
field1, field0,
|
|
TRB_TO_SLOT_ID(field3),
|
|
field3 & TRB_CYCLE ? 'C' : 'c');
|
|
break;
|
|
case TRB_RESET_EP:
|
|
snprintf(str, size,
|
|
"%s: ctx %08x%08x slot %d ep %d flags %c:%c",
|
|
xhci_trb_type_string(type),
|
|
field1, field0,
|
|
TRB_TO_SLOT_ID(field3),
|
|
/* Macro decrements 1, maybe it shouldn't?!? */
|
|
TRB_TO_EP_INDEX(field3) + 1,
|
|
field3 & TRB_TSP ? 'T' : 't',
|
|
field3 & TRB_CYCLE ? 'C' : 'c');
|
|
break;
|
|
case TRB_STOP_RING:
|
|
sprintf(str,
|
|
"%s: slot %d sp %d ep %d flags %c",
|
|
xhci_trb_type_string(type),
|
|
TRB_TO_SLOT_ID(field3),
|
|
TRB_TO_SUSPEND_PORT(field3),
|
|
/* Macro decrements 1, maybe it shouldn't?!? */
|
|
TRB_TO_EP_INDEX(field3) + 1,
|
|
field3 & TRB_CYCLE ? 'C' : 'c');
|
|
break;
|
|
case TRB_SET_DEQ:
|
|
snprintf(str, size,
|
|
"%s: deq %08x%08x stream %d slot %d ep %d flags %c",
|
|
xhci_trb_type_string(type),
|
|
field1, field0,
|
|
TRB_TO_STREAM_ID(field2),
|
|
TRB_TO_SLOT_ID(field3),
|
|
/* Macro decrements 1, maybe it shouldn't?!? */
|
|
TRB_TO_EP_INDEX(field3) + 1,
|
|
field3 & TRB_CYCLE ? 'C' : 'c');
|
|
break;
|
|
case TRB_RESET_DEV:
|
|
snprintf(str, size,
|
|
"%s: slot %d flags %c",
|
|
xhci_trb_type_string(type),
|
|
TRB_TO_SLOT_ID(field3),
|
|
field3 & TRB_CYCLE ? 'C' : 'c');
|
|
break;
|
|
case TRB_FORCE_EVENT:
|
|
snprintf(str, size,
|
|
"%s: event %08x%08x vf intr %d vf id %d flags %c",
|
|
xhci_trb_type_string(type),
|
|
field1, field0,
|
|
TRB_TO_VF_INTR_TARGET(field2),
|
|
TRB_TO_VF_ID(field3),
|
|
field3 & TRB_CYCLE ? 'C' : 'c');
|
|
break;
|
|
case TRB_SET_LT:
|
|
snprintf(str, size,
|
|
"%s: belt %d flags %c",
|
|
xhci_trb_type_string(type),
|
|
TRB_TO_BELT(field3),
|
|
field3 & TRB_CYCLE ? 'C' : 'c');
|
|
break;
|
|
case TRB_GET_BW:
|
|
snprintf(str, size,
|
|
"%s: ctx %08x%08x slot %d speed %d flags %c",
|
|
xhci_trb_type_string(type),
|
|
field1, field0,
|
|
TRB_TO_SLOT_ID(field3),
|
|
TRB_TO_DEV_SPEED(field3),
|
|
field3 & TRB_CYCLE ? 'C' : 'c');
|
|
break;
|
|
case TRB_FORCE_HEADER:
|
|
snprintf(str, size,
|
|
"%s: info %08x%08x%08x pkt type %d roothub port %d flags %c",
|
|
xhci_trb_type_string(type),
|
|
field2, field1, field0 & 0xffffffe0,
|
|
TRB_TO_PACKET_TYPE(field0),
|
|
TRB_TO_ROOTHUB_PORT(field3),
|
|
field3 & TRB_CYCLE ? 'C' : 'c');
|
|
break;
|
|
default:
|
|
snprintf(str, size,
|
|
"type '%s' -> raw %08x %08x %08x %08x",
|
|
xhci_trb_type_string(type),
|
|
field0, field1, field2, field3);
|
|
}
|
|
|
|
return str;
|
|
}
|
|
|
|
static inline const char *xhci_decode_ctrl_ctx(char *str,
|
|
unsigned long drop, unsigned long add)
|
|
{
|
|
unsigned int bit;
|
|
int ret = 0;
|
|
|
|
if (drop) {
|
|
ret = sprintf(str, "Drop:");
|
|
for_each_set_bit(bit, &drop, 32)
|
|
ret += sprintf(str + ret, " %d%s",
|
|
bit / 2,
|
|
bit % 2 ? "in":"out");
|
|
ret += sprintf(str + ret, ", ");
|
|
}
|
|
|
|
if (add) {
|
|
ret += sprintf(str + ret, "Add:%s%s",
|
|
(add & SLOT_FLAG) ? " slot":"",
|
|
(add & EP0_FLAG) ? " ep0":"");
|
|
add &= ~(SLOT_FLAG | EP0_FLAG);
|
|
for_each_set_bit(bit, &add, 32)
|
|
ret += sprintf(str + ret, " %d%s",
|
|
bit / 2,
|
|
bit % 2 ? "in":"out");
|
|
}
|
|
return str;
|
|
}
|
|
|
|
static inline const char *xhci_decode_slot_context(char *str,
|
|
u32 info, u32 info2, u32 tt_info, u32 state)
|
|
{
|
|
u32 speed;
|
|
u32 hub;
|
|
u32 mtt;
|
|
int ret = 0;
|
|
|
|
speed = info & DEV_SPEED;
|
|
hub = info & DEV_HUB;
|
|
mtt = info & DEV_MTT;
|
|
|
|
ret = sprintf(str, "RS %05x %s%s%s Ctx Entries %d MEL %d us Port# %d/%d",
|
|
info & ROUTE_STRING_MASK,
|
|
({ char *s;
|
|
switch (speed) {
|
|
case SLOT_SPEED_FS:
|
|
s = "full-speed";
|
|
break;
|
|
case SLOT_SPEED_LS:
|
|
s = "low-speed";
|
|
break;
|
|
case SLOT_SPEED_HS:
|
|
s = "high-speed";
|
|
break;
|
|
case SLOT_SPEED_SS:
|
|
s = "super-speed";
|
|
break;
|
|
case SLOT_SPEED_SSP:
|
|
s = "super-speed plus";
|
|
break;
|
|
default:
|
|
s = "UNKNOWN speed";
|
|
} s; }),
|
|
mtt ? " multi-TT" : "",
|
|
hub ? " Hub" : "",
|
|
(info & LAST_CTX_MASK) >> 27,
|
|
info2 & MAX_EXIT,
|
|
DEVINFO_TO_ROOT_HUB_PORT(info2),
|
|
DEVINFO_TO_MAX_PORTS(info2));
|
|
|
|
ret += sprintf(str + ret, " [TT Slot %d Port# %d TTT %d Intr %d] Addr %d State %s",
|
|
tt_info & TT_SLOT, (tt_info & TT_PORT) >> 8,
|
|
GET_TT_THINK_TIME(tt_info), GET_INTR_TARGET(tt_info),
|
|
state & DEV_ADDR_MASK,
|
|
xhci_slot_state_string(GET_SLOT_STATE(state)));
|
|
|
|
return str;
|
|
}
|
|
|
|
|
|
static inline const char *xhci_portsc_link_state_string(u32 portsc)
|
|
{
|
|
switch (portsc & PORT_PLS_MASK) {
|
|
case XDEV_U0:
|
|
return "U0";
|
|
case XDEV_U1:
|
|
return "U1";
|
|
case XDEV_U2:
|
|
return "U2";
|
|
case XDEV_U3:
|
|
return "U3";
|
|
case XDEV_DISABLED:
|
|
return "Disabled";
|
|
case XDEV_RXDETECT:
|
|
return "RxDetect";
|
|
case XDEV_INACTIVE:
|
|
return "Inactive";
|
|
case XDEV_POLLING:
|
|
return "Polling";
|
|
case XDEV_RECOVERY:
|
|
return "Recovery";
|
|
case XDEV_HOT_RESET:
|
|
return "Hot Reset";
|
|
case XDEV_COMP_MODE:
|
|
return "Compliance mode";
|
|
case XDEV_TEST_MODE:
|
|
return "Test mode";
|
|
case XDEV_RESUME:
|
|
return "Resume";
|
|
default:
|
|
break;
|
|
}
|
|
return "Unknown";
|
|
}
|
|
|
|
static inline const char *xhci_decode_portsc(char *str, u32 portsc)
|
|
{
|
|
int ret;
|
|
|
|
ret = sprintf(str, "%s %s %s Link:%s PortSpeed:%d ",
|
|
portsc & PORT_POWER ? "Powered" : "Powered-off",
|
|
portsc & PORT_CONNECT ? "Connected" : "Not-connected",
|
|
portsc & PORT_PE ? "Enabled" : "Disabled",
|
|
xhci_portsc_link_state_string(portsc),
|
|
DEV_PORT_SPEED(portsc));
|
|
|
|
if (portsc & PORT_OC)
|
|
ret += sprintf(str + ret, "OverCurrent ");
|
|
if (portsc & PORT_RESET)
|
|
ret += sprintf(str + ret, "In-Reset ");
|
|
|
|
ret += sprintf(str + ret, "Change: ");
|
|
if (portsc & PORT_CSC)
|
|
ret += sprintf(str + ret, "CSC ");
|
|
if (portsc & PORT_PEC)
|
|
ret += sprintf(str + ret, "PEC ");
|
|
if (portsc & PORT_WRC)
|
|
ret += sprintf(str + ret, "WRC ");
|
|
if (portsc & PORT_OCC)
|
|
ret += sprintf(str + ret, "OCC ");
|
|
if (portsc & PORT_RC)
|
|
ret += sprintf(str + ret, "PRC ");
|
|
if (portsc & PORT_PLC)
|
|
ret += sprintf(str + ret, "PLC ");
|
|
if (portsc & PORT_CEC)
|
|
ret += sprintf(str + ret, "CEC ");
|
|
if (portsc & PORT_CAS)
|
|
ret += sprintf(str + ret, "CAS ");
|
|
|
|
ret += sprintf(str + ret, "Wake: ");
|
|
if (portsc & PORT_WKCONN_E)
|
|
ret += sprintf(str + ret, "WCE ");
|
|
if (portsc & PORT_WKDISC_E)
|
|
ret += sprintf(str + ret, "WDE ");
|
|
if (portsc & PORT_WKOC_E)
|
|
ret += sprintf(str + ret, "WOE ");
|
|
|
|
return str;
|
|
}
|
|
|
|
static inline const char *xhci_decode_usbsts(char *str, u32 usbsts)
|
|
{
|
|
int ret = 0;
|
|
|
|
if (usbsts == ~(u32)0)
|
|
return " 0xffffffff";
|
|
if (usbsts & STS_HALT)
|
|
ret += sprintf(str + ret, " HCHalted");
|
|
if (usbsts & STS_FATAL)
|
|
ret += sprintf(str + ret, " HSE");
|
|
if (usbsts & STS_EINT)
|
|
ret += sprintf(str + ret, " EINT");
|
|
if (usbsts & STS_PORT)
|
|
ret += sprintf(str + ret, " PCD");
|
|
if (usbsts & STS_SAVE)
|
|
ret += sprintf(str + ret, " SSS");
|
|
if (usbsts & STS_RESTORE)
|
|
ret += sprintf(str + ret, " RSS");
|
|
if (usbsts & STS_SRE)
|
|
ret += sprintf(str + ret, " SRE");
|
|
if (usbsts & STS_CNR)
|
|
ret += sprintf(str + ret, " CNR");
|
|
if (usbsts & STS_HCE)
|
|
ret += sprintf(str + ret, " HCE");
|
|
|
|
return str;
|
|
}
|
|
|
|
static inline const char *xhci_decode_doorbell(char *str, u32 slot, u32 doorbell)
|
|
{
|
|
u8 ep;
|
|
u16 stream;
|
|
int ret;
|
|
|
|
ep = (doorbell & 0xff);
|
|
stream = doorbell >> 16;
|
|
|
|
if (slot == 0) {
|
|
sprintf(str, "Command Ring %d", doorbell);
|
|
return str;
|
|
}
|
|
ret = sprintf(str, "Slot %d ", slot);
|
|
if (ep > 0 && ep < 32)
|
|
ret = sprintf(str + ret, "ep%d%s",
|
|
ep / 2,
|
|
ep % 2 ? "in" : "out");
|
|
else if (ep == 0 || ep < 248)
|
|
ret = sprintf(str + ret, "Reserved %d", ep);
|
|
else
|
|
ret = sprintf(str + ret, "Vendor Defined %d", ep);
|
|
if (stream)
|
|
ret = sprintf(str + ret, " Stream %d", stream);
|
|
|
|
return str;
|
|
}
|
|
|
|
static inline const char *xhci_ep_state_string(u8 state)
|
|
{
|
|
switch (state) {
|
|
case EP_STATE_DISABLED:
|
|
return "disabled";
|
|
case EP_STATE_RUNNING:
|
|
return "running";
|
|
case EP_STATE_HALTED:
|
|
return "halted";
|
|
case EP_STATE_STOPPED:
|
|
return "stopped";
|
|
case EP_STATE_ERROR:
|
|
return "error";
|
|
default:
|
|
return "INVALID";
|
|
}
|
|
}
|
|
|
|
static inline const char *xhci_ep_type_string(u8 type)
|
|
{
|
|
switch (type) {
|
|
case ISOC_OUT_EP:
|
|
return "Isoc OUT";
|
|
case BULK_OUT_EP:
|
|
return "Bulk OUT";
|
|
case INT_OUT_EP:
|
|
return "Int OUT";
|
|
case CTRL_EP:
|
|
return "Ctrl";
|
|
case ISOC_IN_EP:
|
|
return "Isoc IN";
|
|
case BULK_IN_EP:
|
|
return "Bulk IN";
|
|
case INT_IN_EP:
|
|
return "Int IN";
|
|
default:
|
|
return "INVALID";
|
|
}
|
|
}
|
|
|
|
static inline const char *xhci_decode_ep_context(char *str, u32 info,
|
|
u32 info2, u64 deq, u32 tx_info)
|
|
{
|
|
int ret;
|
|
|
|
u32 esit;
|
|
u16 maxp;
|
|
u16 avg;
|
|
|
|
u8 max_pstr;
|
|
u8 ep_state;
|
|
u8 interval;
|
|
u8 ep_type;
|
|
u8 burst;
|
|
u8 cerr;
|
|
u8 mult;
|
|
|
|
bool lsa;
|
|
bool hid;
|
|
|
|
esit = CTX_TO_MAX_ESIT_PAYLOAD_HI(info) << 16 |
|
|
CTX_TO_MAX_ESIT_PAYLOAD(tx_info);
|
|
|
|
ep_state = info & EP_STATE_MASK;
|
|
max_pstr = CTX_TO_EP_MAXPSTREAMS(info);
|
|
interval = CTX_TO_EP_INTERVAL(info);
|
|
mult = CTX_TO_EP_MULT(info) + 1;
|
|
lsa = !!(info & EP_HAS_LSA);
|
|
|
|
cerr = (info2 & (3 << 1)) >> 1;
|
|
ep_type = CTX_TO_EP_TYPE(info2);
|
|
hid = !!(info2 & (1 << 7));
|
|
burst = CTX_TO_MAX_BURST(info2);
|
|
maxp = MAX_PACKET_DECODED(info2);
|
|
|
|
avg = EP_AVG_TRB_LENGTH(tx_info);
|
|
|
|
ret = sprintf(str, "State %s mult %d max P. Streams %d %s",
|
|
xhci_ep_state_string(ep_state), mult,
|
|
max_pstr, lsa ? "LSA " : "");
|
|
|
|
ret += sprintf(str + ret, "interval %d us max ESIT payload %d CErr %d ",
|
|
(1 << interval) * 125, esit, cerr);
|
|
|
|
ret += sprintf(str + ret, "Type %s %sburst %d maxp %d deq %016llx ",
|
|
xhci_ep_type_string(ep_type), hid ? "HID" : "",
|
|
burst, maxp, deq);
|
|
|
|
ret += sprintf(str + ret, "avg trb len %d", avg);
|
|
|
|
return str;
|
|
}
|
|
|
|
#endif /* __LINUX_XHCI_HCD_H */
|