228 lines
6.5 KiB
C
228 lines
6.5 KiB
C
// SPDX-License-Identifier: GPL-2.0
|
|
/*
|
|
* xHCI host controller driver for R-Car SoCs
|
|
*
|
|
* Copyright (C) 2014 Renesas Electronics Corporation
|
|
*/
|
|
|
|
#include <linux/firmware.h>
|
|
#include <linux/iopoll.h>
|
|
#include <linux/module.h>
|
|
#include <linux/platform_device.h>
|
|
#include <linux/of.h>
|
|
#include <linux/usb/phy.h>
|
|
#include <linux/sys_soc.h>
|
|
|
|
#include "xhci.h"
|
|
#include "xhci-plat.h"
|
|
#include "xhci-rcar.h"
|
|
|
|
/*
|
|
* - The V3 firmware is for almost all R-Car Gen3 (except r8a7795 ES1.x)
|
|
* - The V2 firmware is for r8a7795 ES1.x.
|
|
* - The V2 firmware is possible to use on R-Car Gen2. However, the V2 causes
|
|
* performance degradation. So, this driver continues to use the V1 if R-Car
|
|
* Gen2.
|
|
* - The V1 firmware is impossible to use on R-Car Gen3.
|
|
*/
|
|
MODULE_FIRMWARE(XHCI_RCAR_FIRMWARE_NAME_V1);
|
|
MODULE_FIRMWARE(XHCI_RCAR_FIRMWARE_NAME_V2);
|
|
MODULE_FIRMWARE(XHCI_RCAR_FIRMWARE_NAME_V3);
|
|
|
|
/*** Register Offset ***/
|
|
#define RCAR_USB3_AXH_STA 0x104 /* AXI Host Control Status */
|
|
#define RCAR_USB3_INT_ENA 0x224 /* Interrupt Enable */
|
|
#define RCAR_USB3_DL_CTRL 0x250 /* FW Download Control & Status */
|
|
#define RCAR_USB3_FW_DATA0 0x258 /* FW Data0 */
|
|
|
|
#define RCAR_USB3_LCLK 0xa44 /* LCLK Select */
|
|
#define RCAR_USB3_CONF1 0xa48 /* USB3.0 Configuration1 */
|
|
#define RCAR_USB3_CONF2 0xa5c /* USB3.0 Configuration2 */
|
|
#define RCAR_USB3_CONF3 0xaa8 /* USB3.0 Configuration3 */
|
|
#define RCAR_USB3_RX_POL 0xab0 /* USB3.0 RX Polarity */
|
|
#define RCAR_USB3_TX_POL 0xab8 /* USB3.0 TX Polarity */
|
|
|
|
/*** Register Settings ***/
|
|
/* AXI Host Control Status */
|
|
#define RCAR_USB3_AXH_STA_B3_PLL_ACTIVE 0x00010000
|
|
#define RCAR_USB3_AXH_STA_B2_PLL_ACTIVE 0x00000001
|
|
#define RCAR_USB3_AXH_STA_PLL_ACTIVE_MASK (RCAR_USB3_AXH_STA_B3_PLL_ACTIVE | \
|
|
RCAR_USB3_AXH_STA_B2_PLL_ACTIVE)
|
|
|
|
/* Interrupt Enable */
|
|
#define RCAR_USB3_INT_XHC_ENA 0x00000001
|
|
#define RCAR_USB3_INT_PME_ENA 0x00000002
|
|
#define RCAR_USB3_INT_HSE_ENA 0x00000004
|
|
#define RCAR_USB3_INT_ENA_VAL (RCAR_USB3_INT_XHC_ENA | \
|
|
RCAR_USB3_INT_PME_ENA | RCAR_USB3_INT_HSE_ENA)
|
|
|
|
/* FW Download Control & Status */
|
|
#define RCAR_USB3_DL_CTRL_ENABLE 0x00000001
|
|
#define RCAR_USB3_DL_CTRL_FW_SUCCESS 0x00000010
|
|
#define RCAR_USB3_DL_CTRL_FW_SET_DATA0 0x00000100
|
|
|
|
/* LCLK Select */
|
|
#define RCAR_USB3_LCLK_ENA_VAL 0x01030001
|
|
|
|
/* USB3.0 Configuration */
|
|
#define RCAR_USB3_CONF1_VAL 0x00030204
|
|
#define RCAR_USB3_CONF2_VAL 0x00030300
|
|
#define RCAR_USB3_CONF3_VAL 0x13802007
|
|
|
|
/* USB3.0 Polarity */
|
|
#define RCAR_USB3_RX_POL_VAL BIT(21)
|
|
#define RCAR_USB3_TX_POL_VAL BIT(4)
|
|
|
|
/* For soc_device_attribute */
|
|
#define RCAR_XHCI_FIRMWARE_V2 BIT(0) /* FIRMWARE V2 */
|
|
#define RCAR_XHCI_FIRMWARE_V3 BIT(1) /* FIRMWARE V3 */
|
|
|
|
static const struct soc_device_attribute rcar_quirks_match[] = {
|
|
{
|
|
.soc_id = "r8a7795", .revision = "ES1.*",
|
|
.data = (void *)RCAR_XHCI_FIRMWARE_V2,
|
|
},
|
|
{ /* sentinel */ },
|
|
};
|
|
|
|
static void xhci_rcar_start_gen2(struct usb_hcd *hcd)
|
|
{
|
|
/* LCLK Select */
|
|
writel(RCAR_USB3_LCLK_ENA_VAL, hcd->regs + RCAR_USB3_LCLK);
|
|
/* USB3.0 Configuration */
|
|
writel(RCAR_USB3_CONF1_VAL, hcd->regs + RCAR_USB3_CONF1);
|
|
writel(RCAR_USB3_CONF2_VAL, hcd->regs + RCAR_USB3_CONF2);
|
|
writel(RCAR_USB3_CONF3_VAL, hcd->regs + RCAR_USB3_CONF3);
|
|
/* USB3.0 Polarity */
|
|
writel(RCAR_USB3_RX_POL_VAL, hcd->regs + RCAR_USB3_RX_POL);
|
|
writel(RCAR_USB3_TX_POL_VAL, hcd->regs + RCAR_USB3_TX_POL);
|
|
}
|
|
|
|
static int xhci_rcar_is_gen2(struct device *dev)
|
|
{
|
|
struct device_node *node = dev->of_node;
|
|
|
|
return of_device_is_compatible(node, "renesas,xhci-r8a7790") ||
|
|
of_device_is_compatible(node, "renesas,xhci-r8a7791") ||
|
|
of_device_is_compatible(node, "renesas,xhci-r8a7793") ||
|
|
of_device_is_compatible(node, "renesas,rcar-gen2-xhci");
|
|
}
|
|
|
|
void xhci_rcar_start(struct usb_hcd *hcd)
|
|
{
|
|
u32 temp;
|
|
|
|
if (hcd->regs != NULL) {
|
|
/* Interrupt Enable */
|
|
temp = readl(hcd->regs + RCAR_USB3_INT_ENA);
|
|
temp |= RCAR_USB3_INT_ENA_VAL;
|
|
writel(temp, hcd->regs + RCAR_USB3_INT_ENA);
|
|
if (xhci_rcar_is_gen2(hcd->self.controller))
|
|
xhci_rcar_start_gen2(hcd);
|
|
}
|
|
}
|
|
|
|
static int xhci_rcar_download_firmware(struct usb_hcd *hcd)
|
|
{
|
|
struct device *dev = hcd->self.controller;
|
|
void __iomem *regs = hcd->regs;
|
|
struct xhci_plat_priv *priv = hcd_to_xhci_priv(hcd);
|
|
const struct firmware *fw;
|
|
int retval, index, j;
|
|
u32 data, val, temp;
|
|
u32 quirks = 0;
|
|
const struct soc_device_attribute *attr;
|
|
const char *firmware_name;
|
|
|
|
/*
|
|
* According to the datasheet, "Upon the completion of FW Download,
|
|
* there is no need to write or reload FW".
|
|
*/
|
|
if (readl(regs + RCAR_USB3_DL_CTRL) & RCAR_USB3_DL_CTRL_FW_SUCCESS)
|
|
return 0;
|
|
|
|
attr = soc_device_match(rcar_quirks_match);
|
|
if (attr)
|
|
quirks = (uintptr_t)attr->data;
|
|
|
|
if (quirks & RCAR_XHCI_FIRMWARE_V2)
|
|
firmware_name = XHCI_RCAR_FIRMWARE_NAME_V2;
|
|
else if (quirks & RCAR_XHCI_FIRMWARE_V3)
|
|
firmware_name = XHCI_RCAR_FIRMWARE_NAME_V3;
|
|
else
|
|
firmware_name = priv->firmware_name;
|
|
|
|
/* request R-Car USB3.0 firmware */
|
|
retval = request_firmware(&fw, firmware_name, dev);
|
|
if (retval)
|
|
return retval;
|
|
|
|
/* download R-Car USB3.0 firmware */
|
|
temp = readl(regs + RCAR_USB3_DL_CTRL);
|
|
temp |= RCAR_USB3_DL_CTRL_ENABLE;
|
|
writel(temp, regs + RCAR_USB3_DL_CTRL);
|
|
|
|
for (index = 0; index < fw->size; index += 4) {
|
|
/* to avoid reading beyond the end of the buffer */
|
|
for (data = 0, j = 3; j >= 0; j--) {
|
|
if ((j + index) < fw->size)
|
|
data |= fw->data[index + j] << (8 * j);
|
|
}
|
|
writel(data, regs + RCAR_USB3_FW_DATA0);
|
|
temp = readl(regs + RCAR_USB3_DL_CTRL);
|
|
temp |= RCAR_USB3_DL_CTRL_FW_SET_DATA0;
|
|
writel(temp, regs + RCAR_USB3_DL_CTRL);
|
|
|
|
retval = readl_poll_timeout_atomic(regs + RCAR_USB3_DL_CTRL,
|
|
val, !(val & RCAR_USB3_DL_CTRL_FW_SET_DATA0),
|
|
1, 10000);
|
|
if (retval < 0)
|
|
break;
|
|
}
|
|
|
|
temp = readl(regs + RCAR_USB3_DL_CTRL);
|
|
temp &= ~RCAR_USB3_DL_CTRL_ENABLE;
|
|
writel(temp, regs + RCAR_USB3_DL_CTRL);
|
|
|
|
retval = readl_poll_timeout_atomic((regs + RCAR_USB3_DL_CTRL),
|
|
val, val & RCAR_USB3_DL_CTRL_FW_SUCCESS, 1, 10000);
|
|
|
|
release_firmware(fw);
|
|
|
|
return retval;
|
|
}
|
|
|
|
static bool xhci_rcar_wait_for_pll_active(struct usb_hcd *hcd)
|
|
{
|
|
int retval;
|
|
u32 val, mask = RCAR_USB3_AXH_STA_PLL_ACTIVE_MASK;
|
|
|
|
retval = readl_poll_timeout_atomic(hcd->regs + RCAR_USB3_AXH_STA,
|
|
val, (val & mask) == mask, 1, 1000);
|
|
return !retval;
|
|
}
|
|
|
|
/* This function needs to initialize a "phy" of usb before */
|
|
int xhci_rcar_init_quirk(struct usb_hcd *hcd)
|
|
{
|
|
/* If hcd->regs is NULL, we don't just call the following function */
|
|
if (!hcd->regs)
|
|
return 0;
|
|
|
|
if (!xhci_rcar_wait_for_pll_active(hcd))
|
|
return -ETIMEDOUT;
|
|
|
|
return xhci_rcar_download_firmware(hcd);
|
|
}
|
|
|
|
int xhci_rcar_resume_quirk(struct usb_hcd *hcd)
|
|
{
|
|
int ret;
|
|
|
|
ret = xhci_rcar_download_firmware(hcd);
|
|
if (!ret)
|
|
xhci_rcar_start(hcd);
|
|
|
|
return ret;
|
|
}
|