1008 lines
21 KiB
ReStructuredText
1008 lines
21 KiB
ReStructuredText
.. -*- coding: utf-8; mode: rst -*-
|
|
|
|
.. _fe_property_parameters:
|
|
|
|
******************************
|
|
Digital TV property parameters
|
|
******************************
|
|
|
|
There are several different Digital TV parameters that can be used by
|
|
:ref:`FE_SET_PROPERTY and FE_GET_PROPERTY ioctls<FE_GET_PROPERTY>`.
|
|
This section describes each of them. Please notice, however, that only
|
|
a subset of them are needed to setup a frontend.
|
|
|
|
|
|
.. _DTV-UNDEFINED:
|
|
|
|
DTV_UNDEFINED
|
|
=============
|
|
|
|
Used internally. A GET/SET operation for it won't change or return
|
|
anything.
|
|
|
|
|
|
.. _DTV-TUNE:
|
|
|
|
DTV_TUNE
|
|
========
|
|
|
|
Interpret the cache of data, build either a traditional frontend
|
|
tunerequest so we can pass validation in the ``FE_SET_FRONTEND`` ioctl.
|
|
|
|
|
|
.. _DTV-CLEAR:
|
|
|
|
DTV_CLEAR
|
|
=========
|
|
|
|
Reset a cache of data specific to the frontend here. This does not
|
|
effect hardware.
|
|
|
|
|
|
.. _DTV-FREQUENCY:
|
|
|
|
DTV_FREQUENCY
|
|
=============
|
|
|
|
Frequency of the digital TV transponder/channel.
|
|
|
|
.. note::
|
|
|
|
#. For satellite delivery systems, the frequency is in kHz.
|
|
|
|
#. For cable and terrestrial delivery systems, the frequency is in
|
|
Hz.
|
|
|
|
#. On most delivery systems, the frequency is the center frequency
|
|
of the transponder/channel. The exception is for ISDB-T, where
|
|
the main carrier has a 1/7 offset from the center.
|
|
|
|
#. For ISDB-T, the channels are usually transmitted with an offset of
|
|
about 143kHz. E.g. a valid frequency could be 474,143 kHz. The
|
|
stepping is bound to the bandwidth of the channel which is
|
|
typically 6MHz.
|
|
|
|
#. In ISDB-Tsb, the channel consists of only one or three segments the
|
|
frequency step is 429kHz, 3*429 respectively.
|
|
|
|
|
|
.. _DTV-MODULATION:
|
|
|
|
DTV_MODULATION
|
|
==============
|
|
|
|
Specifies the frontend modulation type for delivery systems that
|
|
supports more multiple modulations.
|
|
|
|
The modulation can be one of the types defined by enum :c:type:`fe_modulation`.
|
|
|
|
Most of the digital TV standards offers more than one possible
|
|
modulation type.
|
|
|
|
The table below presents a summary of the types of modulation types
|
|
supported by each delivery system, as currently defined by specs.
|
|
|
|
======================= =======================================================
|
|
Standard Modulation types
|
|
======================= =======================================================
|
|
ATSC (version 1) 8-VSB and 16-VSB.
|
|
DMTB 4-QAM, 16-QAM, 32-QAM, 64-QAM and 4-QAM-NR.
|
|
DVB-C Annex A/C 16-QAM, 32-QAM, 64-QAM and 256-QAM.
|
|
DVB-C Annex B 64-QAM.
|
|
DVB-T QPSK, 16-QAM and 64-QAM.
|
|
DVB-T2 QPSK, 16-QAM, 64-QAM and 256-QAM.
|
|
DVB-S No need to set. It supports only QPSK.
|
|
DVB-S2 QPSK, 8-PSK, 16-APSK and 32-APSK.
|
|
ISDB-T QPSK, DQPSK, 16-QAM and 64-QAM.
|
|
ISDB-S 8-PSK, QPSK and BPSK.
|
|
======================= =======================================================
|
|
|
|
.. note::
|
|
|
|
Please notice that some of the above modulation types may not be
|
|
defined currently at the Kernel. The reason is simple: no driver
|
|
needed such definition yet.
|
|
|
|
|
|
.. _DTV-BANDWIDTH-HZ:
|
|
|
|
DTV_BANDWIDTH_HZ
|
|
================
|
|
|
|
Bandwidth for the channel, in HZ.
|
|
|
|
Should be set only for terrestrial delivery systems.
|
|
|
|
Possible values: ``1712000``, ``5000000``, ``6000000``, ``7000000``,
|
|
``8000000``, ``10000000``.
|
|
|
|
======================= =======================================================
|
|
Terrestrial Standard Possible values for bandwidth
|
|
======================= =======================================================
|
|
ATSC (version 1) No need to set. It is always 6MHz.
|
|
DMTB No need to set. It is always 8MHz.
|
|
DVB-T 6MHz, 7MHz and 8MHz.
|
|
DVB-T2 1.172 MHz, 5MHz, 6MHz, 7MHz, 8MHz and 10MHz
|
|
ISDB-T 5MHz, 6MHz, 7MHz and 8MHz, although most places
|
|
use 6MHz.
|
|
======================= =======================================================
|
|
|
|
|
|
.. note::
|
|
|
|
|
|
#. For ISDB-Tsb, the bandwidth can vary depending on the number of
|
|
connected segments.
|
|
|
|
It can be easily derived from other parameters
|
|
(DTV_ISDBT_SB_SEGMENT_IDX, DTV_ISDBT_SB_SEGMENT_COUNT).
|
|
|
|
#. On Satellite and Cable delivery systems, the bandwidth depends on
|
|
the symbol rate. So, the Kernel will silently ignore any setting
|
|
:ref:`DTV-BANDWIDTH-HZ`. I will however fill it back with a
|
|
bandwidth estimation.
|
|
|
|
Such bandwidth estimation takes into account the symbol rate set with
|
|
:ref:`DTV-SYMBOL-RATE`, and the rolloff factor, with is fixed for
|
|
DVB-C and DVB-S.
|
|
|
|
For DVB-S2, the rolloff should also be set via :ref:`DTV-ROLLOFF`.
|
|
|
|
|
|
.. _DTV-INVERSION:
|
|
|
|
DTV_INVERSION
|
|
=============
|
|
|
|
Specifies if the frontend should do spectral inversion or not.
|
|
|
|
The acceptable values are defined by :c:type:`fe_spectral_inversion`.
|
|
|
|
|
|
.. _DTV-DISEQC-MASTER:
|
|
|
|
DTV_DISEQC_MASTER
|
|
=================
|
|
|
|
Currently not implemented.
|
|
|
|
|
|
.. _DTV-SYMBOL-RATE:
|
|
|
|
DTV_SYMBOL_RATE
|
|
===============
|
|
|
|
Used on cable and satellite delivery systems.
|
|
|
|
Digital TV symbol rate, in bauds (symbols/second).
|
|
|
|
|
|
.. _DTV-INNER-FEC:
|
|
|
|
DTV_INNER_FEC
|
|
=============
|
|
|
|
Used on cable and satellite delivery systems.
|
|
|
|
The acceptable values are defined by :c:type:`fe_code_rate`.
|
|
|
|
|
|
.. _DTV-VOLTAGE:
|
|
|
|
DTV_VOLTAGE
|
|
===========
|
|
|
|
Used on satellite delivery systems.
|
|
|
|
The voltage is usually used with non-DiSEqC capable LNBs to switch the
|
|
polarzation (horizontal/vertical). When using DiSEqC epuipment this
|
|
voltage has to be switched consistently to the DiSEqC commands as
|
|
described in the DiSEqC spec.
|
|
|
|
The acceptable values are defined by :c:type:`fe_sec_voltage`.
|
|
|
|
|
|
.. _DTV-TONE:
|
|
|
|
DTV_TONE
|
|
========
|
|
|
|
Currently not used.
|
|
|
|
|
|
.. _DTV-PILOT:
|
|
|
|
DTV_PILOT
|
|
=========
|
|
|
|
Used on DVB-S2.
|
|
|
|
Sets DVB-S2 pilot.
|
|
|
|
The acceptable values are defined by :c:type:`fe_pilot`.
|
|
|
|
|
|
.. _DTV-ROLLOFF:
|
|
|
|
DTV_ROLLOFF
|
|
===========
|
|
|
|
Used on DVB-S2.
|
|
|
|
Sets DVB-S2 rolloff.
|
|
|
|
The acceptable values are defined by :c:type:`fe_rolloff`.
|
|
|
|
|
|
.. _DTV-DISEQC-SLAVE-REPLY:
|
|
|
|
DTV_DISEQC_SLAVE_REPLY
|
|
======================
|
|
|
|
Currently not implemented.
|
|
|
|
|
|
.. _DTV-FE-CAPABILITY-COUNT:
|
|
|
|
DTV_FE_CAPABILITY_COUNT
|
|
=======================
|
|
|
|
Currently not implemented.
|
|
|
|
|
|
.. _DTV-FE-CAPABILITY:
|
|
|
|
DTV_FE_CAPABILITY
|
|
=================
|
|
|
|
Currently not implemented.
|
|
|
|
|
|
.. _DTV-DELIVERY-SYSTEM:
|
|
|
|
DTV_DELIVERY_SYSTEM
|
|
===================
|
|
|
|
Specifies the type of the delivery system.
|
|
|
|
The acceptable values are defined by :c:type:`fe_delivery_system`.
|
|
|
|
|
|
.. _DTV-ISDBT-PARTIAL-RECEPTION:
|
|
|
|
DTV_ISDBT_PARTIAL_RECEPTION
|
|
===========================
|
|
|
|
Used only on ISDB.
|
|
|
|
If ``DTV_ISDBT_SOUND_BROADCASTING`` is '0' this bit-field represents
|
|
whether the channel is in partial reception mode or not.
|
|
|
|
If '1' ``DTV_ISDBT_LAYERA_*`` values are assigned to the center segment
|
|
and ``DTV_ISDBT_LAYERA_SEGMENT_COUNT`` has to be '1'.
|
|
|
|
If in addition ``DTV_ISDBT_SOUND_BROADCASTING`` is '1'
|
|
``DTV_ISDBT_PARTIAL_RECEPTION`` represents whether this ISDB-Tsb channel
|
|
is consisting of one segment and layer or three segments and two layers.
|
|
|
|
Possible values: 0, 1, -1 (AUTO)
|
|
|
|
|
|
.. _DTV-ISDBT-SOUND-BROADCASTING:
|
|
|
|
DTV_ISDBT_SOUND_BROADCASTING
|
|
============================
|
|
|
|
Used only on ISDB.
|
|
|
|
This field represents whether the other DTV_ISDBT_*-parameters are
|
|
referring to an ISDB-T and an ISDB-Tsb channel. (See also
|
|
``DTV_ISDBT_PARTIAL_RECEPTION``).
|
|
|
|
Possible values: 0, 1, -1 (AUTO)
|
|
|
|
|
|
.. _DTV-ISDBT-SB-SUBCHANNEL-ID:
|
|
|
|
DTV_ISDBT_SB_SUBCHANNEL_ID
|
|
==========================
|
|
|
|
Used only on ISDB.
|
|
|
|
This field only applies if ``DTV_ISDBT_SOUND_BROADCASTING`` is '1'.
|
|
|
|
(Note of the author: This might not be the correct description of the
|
|
``SUBCHANNEL-ID`` in all details, but it is my understanding of the
|
|
technical background needed to program a device)
|
|
|
|
An ISDB-Tsb channel (1 or 3 segments) can be broadcasted alone or in a
|
|
set of connected ISDB-Tsb channels. In this set of channels every
|
|
channel can be received independently. The number of connected ISDB-Tsb
|
|
segment can vary, e.g. depending on the frequency spectrum bandwidth
|
|
available.
|
|
|
|
Example: Assume 8 ISDB-Tsb connected segments are broadcasted. The
|
|
broadcaster has several possibilities to put those channels in the air:
|
|
Assuming a normal 13-segment ISDB-T spectrum he can align the 8 segments
|
|
from position 1-8 to 5-13 or anything in between.
|
|
|
|
The underlying layer of segments are subchannels: each segment is
|
|
consisting of several subchannels with a predefined IDs. A sub-channel
|
|
is used to help the demodulator to synchronize on the channel.
|
|
|
|
An ISDB-T channel is always centered over all sub-channels. As for the
|
|
example above, in ISDB-Tsb it is no longer as simple as that.
|
|
|
|
``The DTV_ISDBT_SB_SUBCHANNEL_ID`` parameter is used to give the
|
|
sub-channel ID of the segment to be demodulated.
|
|
|
|
Possible values: 0 .. 41, -1 (AUTO)
|
|
|
|
|
|
.. _DTV-ISDBT-SB-SEGMENT-IDX:
|
|
|
|
DTV_ISDBT_SB_SEGMENT_IDX
|
|
========================
|
|
|
|
Used only on ISDB.
|
|
|
|
This field only applies if ``DTV_ISDBT_SOUND_BROADCASTING`` is '1'.
|
|
|
|
``DTV_ISDBT_SB_SEGMENT_IDX`` gives the index of the segment to be
|
|
demodulated for an ISDB-Tsb channel where several of them are
|
|
transmitted in the connected manner.
|
|
|
|
Possible values: 0 .. ``DTV_ISDBT_SB_SEGMENT_COUNT`` - 1
|
|
|
|
Note: This value cannot be determined by an automatic channel search.
|
|
|
|
|
|
.. _DTV-ISDBT-SB-SEGMENT-COUNT:
|
|
|
|
DTV_ISDBT_SB_SEGMENT_COUNT
|
|
==========================
|
|
|
|
Used only on ISDB.
|
|
|
|
This field only applies if ``DTV_ISDBT_SOUND_BROADCASTING`` is '1'.
|
|
|
|
``DTV_ISDBT_SB_SEGMENT_COUNT`` gives the total count of connected
|
|
ISDB-Tsb channels.
|
|
|
|
Possible values: 1 .. 13
|
|
|
|
Note: This value cannot be determined by an automatic channel search.
|
|
|
|
|
|
.. _isdb-hierq-layers:
|
|
|
|
DTV-ISDBT-LAYER[A-C] parameters
|
|
===============================
|
|
|
|
Used only on ISDB.
|
|
|
|
ISDB-T channels can be coded hierarchically. As opposed to DVB-T in
|
|
ISDB-T hierarchical layers can be decoded simultaneously. For that
|
|
reason a ISDB-T demodulator has 3 Viterbi and 3 Reed-Solomon decoders.
|
|
|
|
ISDB-T has 3 hierarchical layers which each can use a part of the
|
|
available segments. The total number of segments over all layers has to
|
|
13 in ISDB-T.
|
|
|
|
There are 3 parameter sets, for Layers A, B and C.
|
|
|
|
|
|
.. _DTV-ISDBT-LAYER-ENABLED:
|
|
|
|
DTV_ISDBT_LAYER_ENABLED
|
|
-----------------------
|
|
|
|
Used only on ISDB.
|
|
|
|
Hierarchical reception in ISDB-T is achieved by enabling or disabling
|
|
layers in the decoding process. Setting all bits of
|
|
``DTV_ISDBT_LAYER_ENABLED`` to '1' forces all layers (if applicable) to
|
|
be demodulated. This is the default.
|
|
|
|
If the channel is in the partial reception mode
|
|
(``DTV_ISDBT_PARTIAL_RECEPTION`` = 1) the central segment can be decoded
|
|
independently of the other 12 segments. In that mode layer A has to have
|
|
a ``SEGMENT_COUNT`` of 1.
|
|
|
|
In ISDB-Tsb only layer A is used, it can be 1 or 3 in ISDB-Tsb according
|
|
to ``DTV_ISDBT_PARTIAL_RECEPTION``. ``SEGMENT_COUNT`` must be filled
|
|
accordingly.
|
|
|
|
Only the values of the first 3 bits are used. Other bits will be silently ignored:
|
|
|
|
``DTV_ISDBT_LAYER_ENABLED`` bit 0: layer A enabled
|
|
|
|
``DTV_ISDBT_LAYER_ENABLED`` bit 1: layer B enabled
|
|
|
|
``DTV_ISDBT_LAYER_ENABLED`` bit 2: layer C enabled
|
|
|
|
``DTV_ISDBT_LAYER_ENABLED`` bits 3-31: unused
|
|
|
|
|
|
.. _DTV-ISDBT-LAYER-FEC:
|
|
|
|
DTV_ISDBT_LAYER[A-C]_FEC
|
|
------------------------
|
|
|
|
Used only on ISDB.
|
|
|
|
The Forward Error Correction mechanism used by a given ISDB Layer, as
|
|
defined by :c:type:`fe_code_rate`.
|
|
|
|
|
|
Possible values are: ``FEC_AUTO``, ``FEC_1_2``, ``FEC_2_3``, ``FEC_3_4``,
|
|
``FEC_5_6``, ``FEC_7_8``
|
|
|
|
|
|
.. _DTV-ISDBT-LAYER-MODULATION:
|
|
|
|
DTV_ISDBT_LAYER[A-C]_MODULATION
|
|
-------------------------------
|
|
|
|
Used only on ISDB.
|
|
|
|
The modulation used by a given ISDB Layer, as defined by
|
|
:c:type:`fe_modulation`.
|
|
|
|
Possible values are: ``QAM_AUTO``, ``QPSK``, ``QAM_16``, ``QAM_64``, ``DQPSK``
|
|
|
|
.. note::
|
|
|
|
#. If layer C is ``DQPSK``, then layer B has to be ``DQPSK``.
|
|
|
|
#. If layer B is ``DQPSK`` and ``DTV_ISDBT_PARTIAL_RECEPTION``\ = 0,
|
|
then layer has to be ``DQPSK``.
|
|
|
|
|
|
.. _DTV-ISDBT-LAYER-SEGMENT-COUNT:
|
|
|
|
DTV_ISDBT_LAYER[A-C]_SEGMENT_COUNT
|
|
----------------------------------
|
|
|
|
Used only on ISDB.
|
|
|
|
Possible values: 0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, -1 (AUTO)
|
|
|
|
Note: Truth table for ``DTV_ISDBT_SOUND_BROADCASTING`` and
|
|
``DTV_ISDBT_PARTIAL_RECEPTION`` and ``LAYER[A-C]_SEGMENT_COUNT``
|
|
|
|
.. _isdbt-layer_seg-cnt-table:
|
|
|
|
.. flat-table:: Truth table for ISDB-T Sound Broadcasting
|
|
:header-rows: 1
|
|
:stub-columns: 0
|
|
|
|
|
|
- .. row 1
|
|
|
|
- Partial Reception
|
|
|
|
- Sound Broadcasting
|
|
|
|
- Layer A width
|
|
|
|
- Layer B width
|
|
|
|
- Layer C width
|
|
|
|
- total width
|
|
|
|
- .. row 2
|
|
|
|
- 0
|
|
|
|
- 0
|
|
|
|
- 1 .. 13
|
|
|
|
- 1 .. 13
|
|
|
|
- 1 .. 13
|
|
|
|
- 13
|
|
|
|
- .. row 3
|
|
|
|
- 1
|
|
|
|
- 0
|
|
|
|
- 1
|
|
|
|
- 1 .. 13
|
|
|
|
- 1 .. 13
|
|
|
|
- 13
|
|
|
|
- .. row 4
|
|
|
|
- 0
|
|
|
|
- 1
|
|
|
|
- 1
|
|
|
|
- 0
|
|
|
|
- 0
|
|
|
|
- 1
|
|
|
|
- .. row 5
|
|
|
|
- 1
|
|
|
|
- 1
|
|
|
|
- 1
|
|
|
|
- 2
|
|
|
|
- 0
|
|
|
|
- 13
|
|
|
|
|
|
|
|
.. _DTV-ISDBT-LAYER-TIME-INTERLEAVING:
|
|
|
|
DTV_ISDBT_LAYER[A-C]_TIME_INTERLEAVING
|
|
--------------------------------------
|
|
|
|
Used only on ISDB.
|
|
|
|
Valid values: 0, 1, 2, 4, -1 (AUTO)
|
|
|
|
when DTV_ISDBT_SOUND_BROADCASTING is active, value 8 is also valid.
|
|
|
|
Note: The real time interleaving length depends on the mode (fft-size).
|
|
The values here are referring to what can be found in the
|
|
TMCC-structure, as shown in the table below.
|
|
|
|
|
|
.. c:type:: isdbt_layer_interleaving_table
|
|
|
|
.. flat-table:: ISDB-T time interleaving modes
|
|
:header-rows: 1
|
|
:stub-columns: 0
|
|
|
|
|
|
- .. row 1
|
|
|
|
- ``DTV_ISDBT_LAYER[A-C]_TIME_INTERLEAVING``
|
|
|
|
- Mode 1 (2K FFT)
|
|
|
|
- Mode 2 (4K FFT)
|
|
|
|
- Mode 3 (8K FFT)
|
|
|
|
- .. row 2
|
|
|
|
- 0
|
|
|
|
- 0
|
|
|
|
- 0
|
|
|
|
- 0
|
|
|
|
- .. row 3
|
|
|
|
- 1
|
|
|
|
- 4
|
|
|
|
- 2
|
|
|
|
- 1
|
|
|
|
- .. row 4
|
|
|
|
- 2
|
|
|
|
- 8
|
|
|
|
- 4
|
|
|
|
- 2
|
|
|
|
- .. row 5
|
|
|
|
- 4
|
|
|
|
- 16
|
|
|
|
- 8
|
|
|
|
- 4
|
|
|
|
|
|
|
|
.. _DTV-ATSCMH-FIC-VER:
|
|
|
|
DTV_ATSCMH_FIC_VER
|
|
------------------
|
|
|
|
Used only on ATSC-MH.
|
|
|
|
Version number of the FIC (Fast Information Channel) signaling data.
|
|
|
|
FIC is used for relaying information to allow rapid service acquisition
|
|
by the receiver.
|
|
|
|
Possible values: 0, 1, 2, 3, ..., 30, 31
|
|
|
|
|
|
.. _DTV-ATSCMH-PARADE-ID:
|
|
|
|
DTV_ATSCMH_PARADE_ID
|
|
--------------------
|
|
|
|
Used only on ATSC-MH.
|
|
|
|
Parade identification number
|
|
|
|
A parade is a collection of up to eight MH groups, conveying one or two
|
|
ensembles.
|
|
|
|
Possible values: 0, 1, 2, 3, ..., 126, 127
|
|
|
|
|
|
.. _DTV-ATSCMH-NOG:
|
|
|
|
DTV_ATSCMH_NOG
|
|
--------------
|
|
|
|
Used only on ATSC-MH.
|
|
|
|
Number of MH groups per MH subframe for a designated parade.
|
|
|
|
Possible values: 1, 2, 3, 4, 5, 6, 7, 8
|
|
|
|
|
|
.. _DTV-ATSCMH-TNOG:
|
|
|
|
DTV_ATSCMH_TNOG
|
|
---------------
|
|
|
|
Used only on ATSC-MH.
|
|
|
|
Total number of MH groups including all MH groups belonging to all MH
|
|
parades in one MH subframe.
|
|
|
|
Possible values: 0, 1, 2, 3, ..., 30, 31
|
|
|
|
|
|
.. _DTV-ATSCMH-SGN:
|
|
|
|
DTV_ATSCMH_SGN
|
|
--------------
|
|
|
|
Used only on ATSC-MH.
|
|
|
|
Start group number.
|
|
|
|
Possible values: 0, 1, 2, 3, ..., 14, 15
|
|
|
|
|
|
.. _DTV-ATSCMH-PRC:
|
|
|
|
DTV_ATSCMH_PRC
|
|
--------------
|
|
|
|
Used only on ATSC-MH.
|
|
|
|
Parade repetition cycle.
|
|
|
|
Possible values: 1, 2, 3, 4, 5, 6, 7, 8
|
|
|
|
|
|
.. _DTV-ATSCMH-RS-FRAME-MODE:
|
|
|
|
DTV_ATSCMH_RS_FRAME_MODE
|
|
------------------------
|
|
|
|
Used only on ATSC-MH.
|
|
|
|
Reed Solomon (RS) frame mode.
|
|
|
|
The acceptable values are defined by :c:type:`atscmh_rs_frame_mode`.
|
|
|
|
|
|
.. _DTV-ATSCMH-RS-FRAME-ENSEMBLE:
|
|
|
|
DTV_ATSCMH_RS_FRAME_ENSEMBLE
|
|
----------------------------
|
|
|
|
Used only on ATSC-MH.
|
|
|
|
Reed Solomon(RS) frame ensemble.
|
|
|
|
The acceptable values are defined by :c:type:`atscmh_rs_frame_ensemble`.
|
|
|
|
|
|
.. _DTV-ATSCMH-RS-CODE-MODE-PRI:
|
|
|
|
DTV_ATSCMH_RS_CODE_MODE_PRI
|
|
---------------------------
|
|
|
|
Used only on ATSC-MH.
|
|
|
|
Reed Solomon (RS) code mode (primary).
|
|
|
|
The acceptable values are defined by :c:type:`atscmh_rs_code_mode`.
|
|
|
|
|
|
.. _DTV-ATSCMH-RS-CODE-MODE-SEC:
|
|
|
|
DTV_ATSCMH_RS_CODE_MODE_SEC
|
|
---------------------------
|
|
|
|
Used only on ATSC-MH.
|
|
|
|
Reed Solomon (RS) code mode (secondary).
|
|
|
|
The acceptable values are defined by :c:type:`atscmh_rs_code_mode`.
|
|
|
|
|
|
.. _DTV-ATSCMH-SCCC-BLOCK-MODE:
|
|
|
|
DTV_ATSCMH_SCCC_BLOCK_MODE
|
|
--------------------------
|
|
|
|
Used only on ATSC-MH.
|
|
|
|
Series Concatenated Convolutional Code Block Mode.
|
|
|
|
The acceptable values are defined by :c:type:`atscmh_sccc_block_mode`.
|
|
|
|
|
|
.. _DTV-ATSCMH-SCCC-CODE-MODE-A:
|
|
|
|
DTV_ATSCMH_SCCC_CODE_MODE_A
|
|
---------------------------
|
|
|
|
Used only on ATSC-MH.
|
|
|
|
Series Concatenated Convolutional Code Rate.
|
|
|
|
The acceptable values are defined by :c:type:`atscmh_sccc_code_mode`.
|
|
|
|
.. _DTV-ATSCMH-SCCC-CODE-MODE-B:
|
|
|
|
DTV_ATSCMH_SCCC_CODE_MODE_B
|
|
---------------------------
|
|
|
|
Used only on ATSC-MH.
|
|
|
|
Series Concatenated Convolutional Code Rate.
|
|
|
|
Possible values are the same as documented on enum
|
|
:c:type:`atscmh_sccc_code_mode`.
|
|
|
|
|
|
.. _DTV-ATSCMH-SCCC-CODE-MODE-C:
|
|
|
|
DTV_ATSCMH_SCCC_CODE_MODE_C
|
|
---------------------------
|
|
|
|
Used only on ATSC-MH.
|
|
|
|
Series Concatenated Convolutional Code Rate.
|
|
|
|
Possible values are the same as documented on enum
|
|
:c:type:`atscmh_sccc_code_mode`.
|
|
|
|
|
|
.. _DTV-ATSCMH-SCCC-CODE-MODE-D:
|
|
|
|
DTV_ATSCMH_SCCC_CODE_MODE_D
|
|
---------------------------
|
|
|
|
Used only on ATSC-MH.
|
|
|
|
Series Concatenated Convolutional Code Rate.
|
|
|
|
Possible values are the same as documented on enum
|
|
:c:type:`atscmh_sccc_code_mode`.
|
|
|
|
|
|
.. _DTV-API-VERSION:
|
|
|
|
DTV_API_VERSION
|
|
===============
|
|
|
|
Returns the major/minor version of the Digital TV API
|
|
|
|
|
|
.. _DTV-CODE-RATE-HP:
|
|
|
|
DTV_CODE_RATE_HP
|
|
================
|
|
|
|
Used on terrestrial transmissions.
|
|
|
|
The acceptable values are defined by :c:type:`fe_transmit_mode`.
|
|
|
|
|
|
.. _DTV-CODE-RATE-LP:
|
|
|
|
DTV_CODE_RATE_LP
|
|
================
|
|
|
|
Used on terrestrial transmissions.
|
|
|
|
The acceptable values are defined by :c:type:`fe_transmit_mode`.
|
|
|
|
|
|
.. _DTV-GUARD-INTERVAL:
|
|
|
|
DTV_GUARD_INTERVAL
|
|
==================
|
|
|
|
The acceptable values are defined by :c:type:`fe_guard_interval`.
|
|
|
|
.. note::
|
|
|
|
#. If ``DTV_GUARD_INTERVAL`` is set the ``GUARD_INTERVAL_AUTO`` the
|
|
hardware will try to find the correct guard interval (if capable) and
|
|
will use TMCC to fill in the missing parameters.
|
|
#. Intervals ``GUARD_INTERVAL_1_128``, ``GUARD_INTERVAL_19_128``
|
|
and ``GUARD_INTERVAL_19_256`` are used only for DVB-T2 at
|
|
present.
|
|
#. Intervals ``GUARD_INTERVAL_PN420``, ``GUARD_INTERVAL_PN595`` and
|
|
``GUARD_INTERVAL_PN945`` are used only for DMTB at the present.
|
|
On such standard, only those intervals and ``GUARD_INTERVAL_AUTO``
|
|
are valid.
|
|
|
|
.. _DTV-TRANSMISSION-MODE:
|
|
|
|
DTV_TRANSMISSION_MODE
|
|
=====================
|
|
|
|
|
|
Used only on OFTM-based standards, e. g. DVB-T/T2, ISDB-T, DTMB.
|
|
|
|
Specifies the FFT size (with corresponds to the approximate number of
|
|
carriers) used by the standard.
|
|
|
|
The acceptable values are defined by :c:type:`fe_transmit_mode`.
|
|
|
|
.. note::
|
|
|
|
#. ISDB-T supports three carrier/symbol-size: 8K, 4K, 2K. It is called
|
|
**mode** on such standard, and are numbered from 1 to 3:
|
|
|
|
==== ======== ========================
|
|
Mode FFT size Transmission mode
|
|
==== ======== ========================
|
|
1 2K ``TRANSMISSION_MODE_2K``
|
|
2 4K ``TRANSMISSION_MODE_4K``
|
|
3 8K ``TRANSMISSION_MODE_8K``
|
|
==== ======== ========================
|
|
|
|
#. If ``DTV_TRANSMISSION_MODE`` is set the ``TRANSMISSION_MODE_AUTO``
|
|
the hardware will try to find the correct FFT-size (if capable) and
|
|
will use TMCC to fill in the missing parameters.
|
|
|
|
#. DVB-T specifies 2K and 8K as valid sizes.
|
|
|
|
#. DVB-T2 specifies 1K, 2K, 4K, 8K, 16K and 32K.
|
|
|
|
#. DTMB specifies C1 and C3780.
|
|
|
|
|
|
.. _DTV-HIERARCHY:
|
|
|
|
DTV_HIERARCHY
|
|
=============
|
|
|
|
Used only on DVB-T and DVB-T2.
|
|
|
|
Frontend hierarchy.
|
|
|
|
The acceptable values are defined by :c:type:`fe_hierarchy`.
|
|
|
|
|
|
.. _DTV-STREAM-ID:
|
|
|
|
DTV_STREAM_ID
|
|
=============
|
|
|
|
Used on DVB-S2, DVB-T2 and ISDB-S.
|
|
|
|
DVB-S2, DVB-T2 and ISDB-S support the transmission of several streams on
|
|
a single transport stream. This property enables the digital TV driver to
|
|
handle substream filtering, when supported by the hardware. By default,
|
|
substream filtering is disabled.
|
|
|
|
For DVB-S2 and DVB-T2, the valid substream id range is from 0 to 255.
|
|
|
|
For ISDB, the valid substream id range is from 1 to 65535.
|
|
|
|
To disable it, you should use the special macro NO_STREAM_ID_FILTER.
|
|
|
|
Note: any value outside the id range also disables filtering.
|
|
|
|
|
|
.. _DTV-DVBT2-PLP-ID-LEGACY:
|
|
|
|
DTV_DVBT2_PLP_ID_LEGACY
|
|
=======================
|
|
|
|
Obsolete, replaced with DTV_STREAM_ID.
|
|
|
|
|
|
.. _DTV-ENUM-DELSYS:
|
|
|
|
DTV_ENUM_DELSYS
|
|
===============
|
|
|
|
A Multi standard frontend needs to advertise the delivery systems
|
|
provided. Applications need to enumerate the provided delivery systems,
|
|
before using any other operation with the frontend. Prior to it's
|
|
introduction, FE_GET_INFO was used to determine a frontend type. A
|
|
frontend which provides more than a single delivery system,
|
|
FE_GET_INFO doesn't help much. Applications which intends to use a
|
|
multistandard frontend must enumerate the delivery systems associated
|
|
with it, rather than trying to use FE_GET_INFO. In the case of a
|
|
legacy frontend, the result is just the same as with FE_GET_INFO, but
|
|
in a more structured format
|
|
|
|
The acceptable values are defined by :c:type:`fe_delivery_system`.
|
|
|
|
|
|
.. _DTV-INTERLEAVING:
|
|
|
|
DTV_INTERLEAVING
|
|
================
|
|
|
|
Time interleaving to be used.
|
|
|
|
The acceptable values are defined by :c:type:`fe_interleaving`.
|
|
|
|
|
|
.. _DTV-LNA:
|
|
|
|
DTV_LNA
|
|
=======
|
|
|
|
Low-noise amplifier.
|
|
|
|
Hardware might offer controllable LNA which can be set manually using
|
|
that parameter. Usually LNA could be found only from terrestrial devices
|
|
if at all.
|
|
|
|
Possible values: 0, 1, LNA_AUTO
|
|
|
|
0, LNA off
|
|
|
|
1, LNA on
|
|
|
|
use the special macro LNA_AUTO to set LNA auto
|
|
|
|
|
|
.. _DTV-SCRAMBLING-SEQUENCE-INDEX:
|
|
|
|
DTV_SCRAMBLING_SEQUENCE_INDEX
|
|
=============================
|
|
|
|
Used on DVB-S2.
|
|
|
|
This 18 bit field, when present, carries the index of the DVB-S2 physical
|
|
layer scrambling sequence as defined in clause 5.5.4 of EN 302 307.
|
|
There is no explicit signalling method to convey scrambling sequence index
|
|
to the receiver. If S2 satellite delivery system descriptor is available
|
|
it can be used to read the scrambling sequence index (EN 300 468 table 41).
|
|
|
|
By default, gold scrambling sequence index 0 is used.
|
|
|
|
The valid scrambling sequence index range is from 0 to 262142.
|