671 lines
20 KiB
C
671 lines
20 KiB
C
/*
|
|
* linux/drivers/ide/pci/piix.c Version 0.45 May 12, 2006
|
|
*
|
|
* Copyright (C) 1998-1999 Andrzej Krzysztofowicz, Author and Maintainer
|
|
* Copyright (C) 1998-2000 Andre Hedrick <andre@linux-ide.org>
|
|
* Copyright (C) 2003 Red Hat Inc <alan@redhat.com>
|
|
* Copyright (C) 2006 MontaVista Software, Inc. <source@mvista.com>
|
|
*
|
|
* May be copied or modified under the terms of the GNU General Public License
|
|
*
|
|
* PIO mode setting function for Intel chipsets.
|
|
* For use instead of BIOS settings.
|
|
*
|
|
* 40-41
|
|
* 42-43
|
|
*
|
|
* 41
|
|
* 43
|
|
*
|
|
* | PIO 0 | c0 | 80 | 0 | piix_tune_drive(drive, 0);
|
|
* | PIO 2 | SW2 | d0 | 90 | 4 | piix_tune_drive(drive, 2);
|
|
* | PIO 3 | MW1 | e1 | a1 | 9 | piix_tune_drive(drive, 3);
|
|
* | PIO 4 | MW2 | e3 | a3 | b | piix_tune_drive(drive, 4);
|
|
*
|
|
* sitre = word40 & 0x4000; primary
|
|
* sitre = word42 & 0x4000; secondary
|
|
*
|
|
* 44 8421|8421 hdd|hdb
|
|
*
|
|
* 48 8421 hdd|hdc|hdb|hda udma enabled
|
|
*
|
|
* 0001 hda
|
|
* 0010 hdb
|
|
* 0100 hdc
|
|
* 1000 hdd
|
|
*
|
|
* 4a 84|21 hdb|hda
|
|
* 4b 84|21 hdd|hdc
|
|
*
|
|
* ata-33/82371AB
|
|
* ata-33/82371EB
|
|
* ata-33/82801AB ata-66/82801AA
|
|
* 00|00 udma 0 00|00 reserved
|
|
* 01|01 udma 1 01|01 udma 3
|
|
* 10|10 udma 2 10|10 udma 4
|
|
* 11|11 reserved 11|11 reserved
|
|
*
|
|
* 54 8421|8421 ata66 drive|ata66 enable
|
|
*
|
|
* pci_read_config_word(HWIF(drive)->pci_dev, 0x40, ®40);
|
|
* pci_read_config_word(HWIF(drive)->pci_dev, 0x42, ®42);
|
|
* pci_read_config_word(HWIF(drive)->pci_dev, 0x44, ®44);
|
|
* pci_read_config_byte(HWIF(drive)->pci_dev, 0x48, ®48);
|
|
* pci_read_config_word(HWIF(drive)->pci_dev, 0x4a, ®4a);
|
|
* pci_read_config_byte(HWIF(drive)->pci_dev, 0x54, ®54);
|
|
*
|
|
* Documentation
|
|
* Publically available from Intel web site. Errata documentation
|
|
* is also publically available. As an aide to anyone hacking on this
|
|
* driver the list of errata that are relevant is below.going back to
|
|
* PIIX4. Older device documentation is now a bit tricky to find.
|
|
*
|
|
* Errata of note:
|
|
*
|
|
* Unfixable
|
|
* PIIX4 errata #9 - Only on ultra obscure hw
|
|
* ICH3 errata #13 - Not observed to affect real hw
|
|
* by Intel
|
|
*
|
|
* Things we must deal with
|
|
* PIIX4 errata #10 - BM IDE hang with non UDMA
|
|
* (must stop/start dma to recover)
|
|
* 440MX errata #15 - As PIIX4 errata #10
|
|
* PIIX4 errata #15 - Must not read control registers
|
|
* during a PIO transfer
|
|
* 440MX errata #13 - As PIIX4 errata #15
|
|
* ICH2 errata #21 - DMA mode 0 doesn't work right
|
|
* ICH0/1 errata #55 - As ICH2 errata #21
|
|
* ICH2 spec c #9 - Extra operations needed to handle
|
|
* drive hotswap [NOT YET SUPPORTED]
|
|
* ICH2 spec c #20 - IDE PRD must not cross a 64K boundary
|
|
* and must be dword aligned
|
|
* ICH2 spec c #24 - UDMA mode 4,5 t85/86 should be 6ns not 3.3
|
|
*
|
|
* Should have been BIOS fixed:
|
|
* 450NX: errata #19 - DMA hangs on old 450NX
|
|
* 450NX: errata #20 - DMA hangs on old 450NX
|
|
* 450NX: errata #25 - Corruption with DMA on old 450NX
|
|
* ICH3 errata #15 - IDE deadlock under high load
|
|
* (BIOS must set dev 31 fn 0 bit 23)
|
|
* ICH3 errata #18 - Don't use native mode
|
|
*/
|
|
|
|
#include <linux/types.h>
|
|
#include <linux/module.h>
|
|
#include <linux/kernel.h>
|
|
#include <linux/ioport.h>
|
|
#include <linux/pci.h>
|
|
#include <linux/hdreg.h>
|
|
#include <linux/ide.h>
|
|
#include <linux/delay.h>
|
|
#include <linux/init.h>
|
|
|
|
#include <asm/io.h>
|
|
|
|
static int no_piix_dma;
|
|
|
|
/**
|
|
* piix_ratemask - compute rate mask for PIIX IDE
|
|
* @drive: IDE drive to compute for
|
|
*
|
|
* Returns the available modes for the PIIX IDE controller.
|
|
*/
|
|
|
|
static u8 piix_ratemask (ide_drive_t *drive)
|
|
{
|
|
struct pci_dev *dev = HWIF(drive)->pci_dev;
|
|
u8 mode;
|
|
|
|
switch(dev->device) {
|
|
case PCI_DEVICE_ID_INTEL_82801EB_1:
|
|
mode = 3;
|
|
break;
|
|
/* UDMA 100 capable */
|
|
case PCI_DEVICE_ID_INTEL_82801BA_8:
|
|
case PCI_DEVICE_ID_INTEL_82801BA_9:
|
|
case PCI_DEVICE_ID_INTEL_82801CA_10:
|
|
case PCI_DEVICE_ID_INTEL_82801CA_11:
|
|
case PCI_DEVICE_ID_INTEL_82801E_11:
|
|
case PCI_DEVICE_ID_INTEL_82801DB_1:
|
|
case PCI_DEVICE_ID_INTEL_82801DB_10:
|
|
case PCI_DEVICE_ID_INTEL_82801DB_11:
|
|
case PCI_DEVICE_ID_INTEL_82801EB_11:
|
|
case PCI_DEVICE_ID_INTEL_ESB_2:
|
|
case PCI_DEVICE_ID_INTEL_ICH6_19:
|
|
case PCI_DEVICE_ID_INTEL_ICH7_21:
|
|
case PCI_DEVICE_ID_INTEL_ESB2_18:
|
|
case PCI_DEVICE_ID_INTEL_ICH8_6:
|
|
mode = 3;
|
|
break;
|
|
/* UDMA 66 capable */
|
|
case PCI_DEVICE_ID_INTEL_82801AA_1:
|
|
case PCI_DEVICE_ID_INTEL_82372FB_1:
|
|
mode = 2;
|
|
break;
|
|
/* UDMA 33 capable */
|
|
case PCI_DEVICE_ID_INTEL_82371AB:
|
|
case PCI_DEVICE_ID_INTEL_82443MX_1:
|
|
case PCI_DEVICE_ID_INTEL_82451NX:
|
|
case PCI_DEVICE_ID_INTEL_82801AB_1:
|
|
return 1;
|
|
/* Non UDMA capable (MWDMA2) */
|
|
case PCI_DEVICE_ID_INTEL_82371SB_1:
|
|
case PCI_DEVICE_ID_INTEL_82371FB_1:
|
|
case PCI_DEVICE_ID_INTEL_82371FB_0:
|
|
case PCI_DEVICE_ID_INTEL_82371MX:
|
|
default:
|
|
return 0;
|
|
}
|
|
|
|
/*
|
|
* If we are UDMA66 capable fall back to UDMA33
|
|
* if the drive cannot see an 80pin cable.
|
|
*/
|
|
if (!eighty_ninty_three(drive))
|
|
mode = min(mode, (u8)1);
|
|
return mode;
|
|
}
|
|
|
|
/**
|
|
* piix_dma_2_pio - return the PIO mode matching DMA
|
|
* @xfer_rate: transfer speed
|
|
*
|
|
* Returns the nearest equivalent PIO timing for the PIO or DMA
|
|
* mode requested by the controller.
|
|
*/
|
|
|
|
static u8 piix_dma_2_pio (u8 xfer_rate) {
|
|
switch(xfer_rate) {
|
|
case XFER_UDMA_6:
|
|
case XFER_UDMA_5:
|
|
case XFER_UDMA_4:
|
|
case XFER_UDMA_3:
|
|
case XFER_UDMA_2:
|
|
case XFER_UDMA_1:
|
|
case XFER_UDMA_0:
|
|
case XFER_MW_DMA_2:
|
|
case XFER_PIO_4:
|
|
return 4;
|
|
case XFER_MW_DMA_1:
|
|
case XFER_PIO_3:
|
|
return 3;
|
|
case XFER_SW_DMA_2:
|
|
case XFER_PIO_2:
|
|
return 2;
|
|
case XFER_MW_DMA_0:
|
|
case XFER_SW_DMA_1:
|
|
case XFER_SW_DMA_0:
|
|
case XFER_PIO_1:
|
|
case XFER_PIO_0:
|
|
case XFER_PIO_SLOW:
|
|
default:
|
|
return 0;
|
|
}
|
|
}
|
|
|
|
/**
|
|
* piix_tune_drive - tune a drive attached to a PIIX
|
|
* @drive: drive to tune
|
|
* @pio: desired PIO mode
|
|
*
|
|
* Set the interface PIO mode based upon the settings done by AMI BIOS
|
|
* (might be useful if drive is not registered in CMOS for any reason).
|
|
*/
|
|
static void piix_tune_drive (ide_drive_t *drive, u8 pio)
|
|
{
|
|
ide_hwif_t *hwif = HWIF(drive);
|
|
struct pci_dev *dev = hwif->pci_dev;
|
|
int is_slave = (&hwif->drives[1] == drive);
|
|
int master_port = hwif->channel ? 0x42 : 0x40;
|
|
int slave_port = 0x44;
|
|
unsigned long flags;
|
|
u16 master_data;
|
|
u8 slave_data;
|
|
static DEFINE_SPINLOCK(tune_lock);
|
|
int control = 0;
|
|
|
|
/* ISP RTC */
|
|
static const u8 timings[][2]= {
|
|
{ 0, 0 },
|
|
{ 0, 0 },
|
|
{ 1, 0 },
|
|
{ 2, 1 },
|
|
{ 2, 3 }, };
|
|
|
|
pio = ide_get_best_pio_mode(drive, pio, 5, NULL);
|
|
|
|
/*
|
|
* Master vs slave is synchronized above us but the slave register is
|
|
* shared by the two hwifs so the corner case of two slave timeouts in
|
|
* parallel must be locked.
|
|
*/
|
|
spin_lock_irqsave(&tune_lock, flags);
|
|
pci_read_config_word(dev, master_port, &master_data);
|
|
|
|
if (pio >= 2)
|
|
control |= 1; /* Programmable timing on */
|
|
if (drive->media == ide_disk)
|
|
control |= 4; /* Prefetch, post write */
|
|
if (pio >= 3)
|
|
control |= 2; /* IORDY */
|
|
if (is_slave) {
|
|
master_data = master_data | 0x4000;
|
|
if (pio > 1) {
|
|
/* enable PPE, IE and TIME */
|
|
master_data = master_data | (control << 4);
|
|
} else {
|
|
master_data &= ~0x0070;
|
|
}
|
|
pci_read_config_byte(dev, slave_port, &slave_data);
|
|
slave_data = slave_data & (hwif->channel ? 0x0f : 0xf0);
|
|
slave_data = slave_data | (((timings[pio][0] << 2) | timings[pio][1]) << (hwif->channel ? 4 : 0));
|
|
} else {
|
|
master_data = master_data & 0xccf8;
|
|
if (pio > 1) {
|
|
/* enable PPE, IE and TIME */
|
|
master_data = master_data | control;
|
|
}
|
|
master_data = master_data | (timings[pio][0] << 12) | (timings[pio][1] << 8);
|
|
}
|
|
pci_write_config_word(dev, master_port, master_data);
|
|
if (is_slave)
|
|
pci_write_config_byte(dev, slave_port, slave_data);
|
|
spin_unlock_irqrestore(&tune_lock, flags);
|
|
}
|
|
|
|
/**
|
|
* piix_tune_chipset - tune a PIIX interface
|
|
* @drive: IDE drive to tune
|
|
* @xferspeed: speed to configure
|
|
*
|
|
* Set a PIIX interface channel to the desired speeds. This involves
|
|
* requires the right timing data into the PIIX configuration space
|
|
* then setting the drive parameters appropriately
|
|
*/
|
|
|
|
static int piix_tune_chipset (ide_drive_t *drive, u8 xferspeed)
|
|
{
|
|
ide_hwif_t *hwif = HWIF(drive);
|
|
struct pci_dev *dev = hwif->pci_dev;
|
|
u8 maslave = hwif->channel ? 0x42 : 0x40;
|
|
u8 speed = ide_rate_filter(piix_ratemask(drive), xferspeed);
|
|
int a_speed = 3 << (drive->dn * 4);
|
|
int u_flag = 1 << drive->dn;
|
|
int v_flag = 0x01 << drive->dn;
|
|
int w_flag = 0x10 << drive->dn;
|
|
int u_speed = 0;
|
|
int sitre;
|
|
u16 reg4042, reg4a;
|
|
u8 reg48, reg54, reg55;
|
|
|
|
pci_read_config_word(dev, maslave, ®4042);
|
|
sitre = (reg4042 & 0x4000) ? 1 : 0;
|
|
pci_read_config_byte(dev, 0x48, ®48);
|
|
pci_read_config_word(dev, 0x4a, ®4a);
|
|
pci_read_config_byte(dev, 0x54, ®54);
|
|
pci_read_config_byte(dev, 0x55, ®55);
|
|
|
|
switch(speed) {
|
|
case XFER_UDMA_4:
|
|
case XFER_UDMA_2: u_speed = 2 << (drive->dn * 4); break;
|
|
case XFER_UDMA_5:
|
|
case XFER_UDMA_3:
|
|
case XFER_UDMA_1: u_speed = 1 << (drive->dn * 4); break;
|
|
case XFER_UDMA_0: u_speed = 0 << (drive->dn * 4); break;
|
|
case XFER_MW_DMA_2:
|
|
case XFER_MW_DMA_1:
|
|
case XFER_SW_DMA_2: break;
|
|
case XFER_PIO_4:
|
|
case XFER_PIO_3:
|
|
case XFER_PIO_2:
|
|
case XFER_PIO_0: break;
|
|
default: return -1;
|
|
}
|
|
|
|
if (speed >= XFER_UDMA_0) {
|
|
if (!(reg48 & u_flag))
|
|
pci_write_config_byte(dev, 0x48, reg48 | u_flag);
|
|
if (speed == XFER_UDMA_5) {
|
|
pci_write_config_byte(dev, 0x55, (u8) reg55|w_flag);
|
|
} else {
|
|
pci_write_config_byte(dev, 0x55, (u8) reg55 & ~w_flag);
|
|
}
|
|
if ((reg4a & a_speed) != u_speed)
|
|
pci_write_config_word(dev, 0x4a, (reg4a & ~a_speed) | u_speed);
|
|
if (speed > XFER_UDMA_2) {
|
|
if (!(reg54 & v_flag))
|
|
pci_write_config_byte(dev, 0x54, reg54 | v_flag);
|
|
} else
|
|
pci_write_config_byte(dev, 0x54, reg54 & ~v_flag);
|
|
} else {
|
|
if (reg48 & u_flag)
|
|
pci_write_config_byte(dev, 0x48, reg48 & ~u_flag);
|
|
if (reg4a & a_speed)
|
|
pci_write_config_word(dev, 0x4a, reg4a & ~a_speed);
|
|
if (reg54 & v_flag)
|
|
pci_write_config_byte(dev, 0x54, reg54 & ~v_flag);
|
|
if (reg55 & w_flag)
|
|
pci_write_config_byte(dev, 0x55, (u8) reg55 & ~w_flag);
|
|
}
|
|
|
|
piix_tune_drive(drive, piix_dma_2_pio(speed));
|
|
return (ide_config_drive_speed(drive, speed));
|
|
}
|
|
|
|
/**
|
|
* piix_config_drive_for_dma - configure drive for DMA
|
|
* @drive: IDE drive to configure
|
|
*
|
|
* Set up a PIIX interface channel for the best available speed.
|
|
* We prefer UDMA if it is available and then MWDMA. If DMA is
|
|
* not available we switch to PIO and return 0.
|
|
*/
|
|
|
|
static int piix_config_drive_for_dma (ide_drive_t *drive)
|
|
{
|
|
u8 speed = ide_dma_speed(drive, piix_ratemask(drive));
|
|
|
|
/*
|
|
* If no DMA speed was available or the chipset has DMA bugs
|
|
* then disable DMA and use PIO
|
|
*/
|
|
if (!speed || no_piix_dma)
|
|
return 0;
|
|
|
|
(void) piix_tune_chipset(drive, speed);
|
|
return ide_dma_enable(drive);
|
|
}
|
|
|
|
/**
|
|
* piix_config_drive_xfer_rate - set up an IDE device
|
|
* @drive: IDE drive to configure
|
|
*
|
|
* Set up the PIIX interface for the best available speed on this
|
|
* interface, preferring DMA to PIO.
|
|
*/
|
|
|
|
static int piix_config_drive_xfer_rate (ide_drive_t *drive)
|
|
{
|
|
ide_hwif_t *hwif = HWIF(drive);
|
|
struct hd_driveid *id = drive->id;
|
|
|
|
drive->init_speed = 0;
|
|
|
|
if ((id->capability & 1) && drive->autodma) {
|
|
|
|
if (ide_use_dma(drive) && piix_config_drive_for_dma(drive))
|
|
return hwif->ide_dma_on(drive);
|
|
|
|
goto fast_ata_pio;
|
|
|
|
} else if ((id->capability & 8) || (id->field_valid & 2)) {
|
|
fast_ata_pio:
|
|
/* Find best PIO mode. */
|
|
(void) hwif->speedproc(drive, XFER_PIO_0 +
|
|
ide_get_best_pio_mode(drive, 255, 4, NULL));
|
|
return hwif->ide_dma_off_quietly(drive);
|
|
}
|
|
/* IORDY not supported */
|
|
return 0;
|
|
}
|
|
|
|
/**
|
|
* init_chipset_piix - set up the PIIX chipset
|
|
* @dev: PCI device to set up
|
|
* @name: Name of the device
|
|
*
|
|
* Initialize the PCI device as required. For the PIIX this turns
|
|
* out to be nice and simple
|
|
*/
|
|
|
|
static unsigned int __devinit init_chipset_piix (struct pci_dev *dev, const char *name)
|
|
{
|
|
switch(dev->device) {
|
|
case PCI_DEVICE_ID_INTEL_82801EB_1:
|
|
case PCI_DEVICE_ID_INTEL_82801AA_1:
|
|
case PCI_DEVICE_ID_INTEL_82801AB_1:
|
|
case PCI_DEVICE_ID_INTEL_82801BA_8:
|
|
case PCI_DEVICE_ID_INTEL_82801BA_9:
|
|
case PCI_DEVICE_ID_INTEL_82801CA_10:
|
|
case PCI_DEVICE_ID_INTEL_82801CA_11:
|
|
case PCI_DEVICE_ID_INTEL_82801DB_1:
|
|
case PCI_DEVICE_ID_INTEL_82801DB_10:
|
|
case PCI_DEVICE_ID_INTEL_82801DB_11:
|
|
case PCI_DEVICE_ID_INTEL_82801EB_11:
|
|
case PCI_DEVICE_ID_INTEL_82801E_11:
|
|
case PCI_DEVICE_ID_INTEL_ESB_2:
|
|
case PCI_DEVICE_ID_INTEL_ICH6_19:
|
|
case PCI_DEVICE_ID_INTEL_ICH7_21:
|
|
case PCI_DEVICE_ID_INTEL_ESB2_18:
|
|
case PCI_DEVICE_ID_INTEL_ICH8_6:
|
|
{
|
|
unsigned int extra = 0;
|
|
pci_read_config_dword(dev, 0x54, &extra);
|
|
pci_write_config_dword(dev, 0x54, extra|0x400);
|
|
}
|
|
default:
|
|
break;
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
/**
|
|
* init_hwif_piix - fill in the hwif for the PIIX
|
|
* @hwif: IDE interface
|
|
*
|
|
* Set up the ide_hwif_t for the PIIX interface according to the
|
|
* capabilities of the hardware.
|
|
*/
|
|
|
|
static void __devinit init_hwif_piix(ide_hwif_t *hwif)
|
|
{
|
|
u8 reg54h = 0, reg55h = 0, ata66 = 0;
|
|
u8 mask = hwif->channel ? 0xc0 : 0x30;
|
|
|
|
#ifndef CONFIG_IA64
|
|
if (!hwif->irq)
|
|
hwif->irq = hwif->channel ? 15 : 14;
|
|
#endif /* CONFIG_IA64 */
|
|
|
|
if (hwif->pci_dev->device == PCI_DEVICE_ID_INTEL_82371MX) {
|
|
/* This is a painful system best to let it self tune for now */
|
|
return;
|
|
}
|
|
/* ESB2 appears to generate spurious DMA interrupts in PIO mode
|
|
when in native mode */
|
|
if (hwif->pci_dev->device == PCI_DEVICE_ID_INTEL_ESB2_18)
|
|
hwif->atapi_irq_bogon = 1;
|
|
|
|
hwif->autodma = 0;
|
|
hwif->tuneproc = &piix_tune_drive;
|
|
hwif->speedproc = &piix_tune_chipset;
|
|
hwif->drives[0].autotune = 1;
|
|
hwif->drives[1].autotune = 1;
|
|
|
|
if (!hwif->dma_base)
|
|
return;
|
|
|
|
hwif->atapi_dma = 1;
|
|
hwif->ultra_mask = 0x3f;
|
|
hwif->mwdma_mask = 0x06;
|
|
hwif->swdma_mask = 0x04;
|
|
|
|
switch(hwif->pci_dev->device) {
|
|
case PCI_DEVICE_ID_INTEL_82371MX:
|
|
hwif->mwdma_mask = 0x80;
|
|
hwif->swdma_mask = 0x80;
|
|
case PCI_DEVICE_ID_INTEL_82371FB_0:
|
|
case PCI_DEVICE_ID_INTEL_82371FB_1:
|
|
case PCI_DEVICE_ID_INTEL_82371SB_1:
|
|
hwif->ultra_mask = 0x80;
|
|
break;
|
|
case PCI_DEVICE_ID_INTEL_82371AB:
|
|
case PCI_DEVICE_ID_INTEL_82443MX_1:
|
|
case PCI_DEVICE_ID_INTEL_82451NX:
|
|
case PCI_DEVICE_ID_INTEL_82801AB_1:
|
|
hwif->ultra_mask = 0x07;
|
|
break;
|
|
default:
|
|
pci_read_config_byte(hwif->pci_dev, 0x54, ®54h);
|
|
pci_read_config_byte(hwif->pci_dev, 0x55, ®55h);
|
|
ata66 = (reg54h & mask) ? 1 : 0;
|
|
break;
|
|
}
|
|
|
|
if (!(hwif->udma_four))
|
|
hwif->udma_four = ata66;
|
|
hwif->ide_dma_check = &piix_config_drive_xfer_rate;
|
|
if (!noautodma)
|
|
hwif->autodma = 1;
|
|
|
|
hwif->drives[1].autodma = hwif->autodma;
|
|
hwif->drives[0].autodma = hwif->autodma;
|
|
}
|
|
|
|
#define DECLARE_PIIX_DEV(name_str) \
|
|
{ \
|
|
.name = name_str, \
|
|
.init_chipset = init_chipset_piix, \
|
|
.init_hwif = init_hwif_piix, \
|
|
.channels = 2, \
|
|
.autodma = AUTODMA, \
|
|
.enablebits = {{0x41,0x80,0x80}, {0x43,0x80,0x80}}, \
|
|
.bootable = ON_BOARD, \
|
|
}
|
|
|
|
static ide_pci_device_t piix_pci_info[] __devinitdata = {
|
|
/* 0 */ DECLARE_PIIX_DEV("PIIXa"),
|
|
/* 1 */ DECLARE_PIIX_DEV("PIIXb"),
|
|
|
|
{ /* 2 */
|
|
.name = "MPIIX",
|
|
.init_hwif = init_hwif_piix,
|
|
.channels = 2,
|
|
.autodma = NODMA,
|
|
.enablebits = {{0x6D,0x80,0x80}, {0x6F,0x80,0x80}},
|
|
.bootable = ON_BOARD,
|
|
},
|
|
|
|
/* 3 */ DECLARE_PIIX_DEV("PIIX3"),
|
|
/* 4 */ DECLARE_PIIX_DEV("PIIX4"),
|
|
/* 5 */ DECLARE_PIIX_DEV("ICH0"),
|
|
/* 6 */ DECLARE_PIIX_DEV("PIIX4"),
|
|
/* 7 */ DECLARE_PIIX_DEV("ICH"),
|
|
/* 8 */ DECLARE_PIIX_DEV("PIIX4"),
|
|
/* 9 */ DECLARE_PIIX_DEV("PIIX4"),
|
|
/* 10 */ DECLARE_PIIX_DEV("ICH2"),
|
|
/* 11 */ DECLARE_PIIX_DEV("ICH2M"),
|
|
/* 12 */ DECLARE_PIIX_DEV("ICH3M"),
|
|
/* 13 */ DECLARE_PIIX_DEV("ICH3"),
|
|
/* 14 */ DECLARE_PIIX_DEV("ICH4"),
|
|
/* 15 */ DECLARE_PIIX_DEV("ICH5"),
|
|
/* 16 */ DECLARE_PIIX_DEV("C-ICH"),
|
|
/* 17 */ DECLARE_PIIX_DEV("ICH4"),
|
|
/* 18 */ DECLARE_PIIX_DEV("ICH5-SATA"),
|
|
/* 19 */ DECLARE_PIIX_DEV("ICH5"),
|
|
/* 20 */ DECLARE_PIIX_DEV("ICH6"),
|
|
/* 21 */ DECLARE_PIIX_DEV("ICH7"),
|
|
/* 22 */ DECLARE_PIIX_DEV("ICH4"),
|
|
/* 23 */ DECLARE_PIIX_DEV("ESB2"),
|
|
/* 24 */ DECLARE_PIIX_DEV("ICH8M"),
|
|
};
|
|
|
|
/**
|
|
* piix_init_one - called when a PIIX is found
|
|
* @dev: the piix device
|
|
* @id: the matching pci id
|
|
*
|
|
* Called when the PCI registration layer (or the IDE initialization)
|
|
* finds a device matching our IDE device tables.
|
|
*/
|
|
|
|
static int __devinit piix_init_one(struct pci_dev *dev, const struct pci_device_id *id)
|
|
{
|
|
ide_pci_device_t *d = &piix_pci_info[id->driver_data];
|
|
|
|
return ide_setup_pci_device(dev, d);
|
|
}
|
|
|
|
/**
|
|
* piix_check_450nx - Check for problem 450NX setup
|
|
*
|
|
* Check for the present of 450NX errata #19 and errata #25. If
|
|
* they are found, disable use of DMA IDE
|
|
*/
|
|
|
|
static void __devinit piix_check_450nx(void)
|
|
{
|
|
struct pci_dev *pdev = NULL;
|
|
u16 cfg;
|
|
u8 rev;
|
|
while((pdev=pci_get_device(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82454NX, pdev))!=NULL)
|
|
{
|
|
/* Look for 450NX PXB. Check for problem configurations
|
|
A PCI quirk checks bit 6 already */
|
|
pci_read_config_byte(pdev, PCI_REVISION_ID, &rev);
|
|
pci_read_config_word(pdev, 0x41, &cfg);
|
|
/* Only on the original revision: IDE DMA can hang */
|
|
if(rev == 0x00)
|
|
no_piix_dma = 1;
|
|
/* On all revisions below 5 PXB bus lock must be disabled for IDE */
|
|
else if(cfg & (1<<14) && rev < 5)
|
|
no_piix_dma = 2;
|
|
}
|
|
if(no_piix_dma)
|
|
printk(KERN_WARNING "piix: 450NX errata present, disabling IDE DMA.\n");
|
|
if(no_piix_dma == 2)
|
|
printk(KERN_WARNING "piix: A BIOS update may resolve this.\n");
|
|
}
|
|
|
|
static struct pci_device_id piix_pci_tbl[] = {
|
|
{ PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82371FB_0, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0},
|
|
{ PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82371FB_1, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 1},
|
|
{ PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82371MX, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 2},
|
|
{ PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82371SB_1, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 3},
|
|
{ PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82371AB, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 4},
|
|
{ PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801AB_1, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 5},
|
|
{ PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82443MX_1, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 6},
|
|
{ PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801AA_1, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 7},
|
|
{ PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82372FB_1, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 8},
|
|
{ PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82451NX, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 9},
|
|
{ PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801BA_9, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 10},
|
|
{ PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801BA_8, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 11},
|
|
{ PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801CA_10,PCI_ANY_ID, PCI_ANY_ID, 0, 0, 12},
|
|
{ PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801CA_11,PCI_ANY_ID, PCI_ANY_ID, 0, 0, 13},
|
|
{ PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801DB_11,PCI_ANY_ID, PCI_ANY_ID, 0, 0, 14},
|
|
{ PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801EB_11,PCI_ANY_ID, PCI_ANY_ID, 0, 0, 15},
|
|
{ PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801E_11, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 16},
|
|
{ PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801DB_10,PCI_ANY_ID, PCI_ANY_ID, 0, 0, 17},
|
|
#ifdef CONFIG_BLK_DEV_IDE_SATA
|
|
{ PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801EB_1, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 18},
|
|
#endif
|
|
{ PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ESB_2, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 19},
|
|
{ PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH6_19, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 20},
|
|
{ PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH7_21, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 21},
|
|
{ PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801DB_1, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 22},
|
|
{ PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ESB2_18, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 23},
|
|
{ PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH8_6, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 24},
|
|
{ 0, },
|
|
};
|
|
MODULE_DEVICE_TABLE(pci, piix_pci_tbl);
|
|
|
|
static struct pci_driver driver = {
|
|
.name = "PIIX_IDE",
|
|
.id_table = piix_pci_tbl,
|
|
.probe = piix_init_one,
|
|
};
|
|
|
|
static int __init piix_ide_init(void)
|
|
{
|
|
piix_check_450nx();
|
|
return ide_pci_register_driver(&driver);
|
|
}
|
|
|
|
module_init(piix_ide_init);
|
|
|
|
MODULE_AUTHOR("Andre Hedrick, Andrzej Krzysztofowicz");
|
|
MODULE_DESCRIPTION("PCI driver module for Intel PIIX IDE");
|
|
MODULE_LICENSE("GPL");
|