67 lines
3.0 KiB
Plaintext
67 lines
3.0 KiB
Plaintext
Microchip USB 2.0 Hi-Speed Hub Controller
|
|
|
|
The device node for the configuration of a Microchip USB251xB/xBi USB 2.0
|
|
Hi-Speed Controller.
|
|
|
|
Required properties :
|
|
- compatible : Should be "microchip,usb251xb" or one of the specific types:
|
|
"microchip,usb2512b", "microchip,usb2512bi", "microchip,usb2513b",
|
|
"microchip,usb2513bi", "microchip,usb2514b", "microchip,usb2514bi"
|
|
- reset-gpios : Should specify the gpio for hub reset
|
|
- reg : I2C address on the selected bus (default is <0x2C>)
|
|
|
|
Optional properties :
|
|
- skip-config : Skip Hub configuration, but only send the USB-Attach command
|
|
- vendor-id : Set USB Vendor ID of the hub (16 bit, default is 0x0424)
|
|
- product-id : Set USB Product ID of the hub (16 bit, default depends on type)
|
|
- device-id : Set USB Device ID of the hub (16 bit, default is 0x0bb3)
|
|
- language-id : Set USB Language ID (16 bit, default is 0x0000)
|
|
- manufacturer : Set USB Manufacturer string (max 31 characters long)
|
|
- product : Set USB Product string (max 31 characters long)
|
|
- serial : Set USB Serial string (max 31 characters long)
|
|
- {bus,self}-powered : selects between self- and bus-powered operation (default
|
|
is self-powered)
|
|
- disable-hi-speed : disable USB Hi-Speed support
|
|
- {multi,single}-tt : selects between multi- and single-transaction-translator
|
|
(default is multi-tt)
|
|
- disable-eop : disable End of Packet generation in full-speed mode
|
|
- {ganged,individual}-sensing : select over-current sense type in self-powered
|
|
mode (default is individual)
|
|
- {ganged,individual}-port-switching : select port power switching mode
|
|
(default is individual)
|
|
- dynamic-power-switching : enable auto-switching from self- to bus-powered
|
|
operation if the local power source is removed or unavailable
|
|
- oc-delay-us : Delay time (in microseconds) for filtering the over-current
|
|
sense inputs. Valid values are 100, 4000, 8000 (default) and 16000. If
|
|
an invalid value is given, the default is used instead.
|
|
- compound-device : indicate the hub is part of a compound device
|
|
- port-mapping-mode : enable port mapping mode
|
|
- string-support : enable string descriptor support (required for manufacturer,
|
|
product and serial string configuration)
|
|
- non-removable-ports : Should specify the ports which have a non-removable
|
|
device connected.
|
|
- sp-disabled-ports : Specifies the ports which will be self-power disabled
|
|
- bp-disabled-ports : Specifies the ports which will be bus-power disabled
|
|
- power-on-time-ms : Specifies the time it takes from the time the host
|
|
initiates the power-on sequence to a port until the port has adequate
|
|
power. The value is given in ms in a 0 - 510 range (default is 100ms).
|
|
|
|
Examples:
|
|
usb2512b@2c {
|
|
compatible = "microchip,usb2512b";
|
|
reg = <0x2c>;
|
|
reset-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
usb2514b@2c {
|
|
compatible = "microchip,usb2514b";
|
|
reg = <0x2c>;
|
|
reset-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>;
|
|
vendor-id = /bits/ 16 <0x0000>;
|
|
product-id = /bits/ 16 <0x0000>;
|
|
string-support;
|
|
manufacturer = "Foo";
|
|
product = "Foo-Bar";
|
|
serial = "1234567890A";
|
|
};
|