OpenCloudOS-Kernel/drivers/usb/serial/ssu100.c

581 lines
14 KiB
C

// SPDX-License-Identifier: GPL-2.0
/*
* usb-serial driver for Quatech SSU-100
*
* based on ftdi_sio.c and the original serqt_usb.c from Quatech
*
*/
#include <linux/errno.h>
#include <linux/slab.h>
#include <linux/tty.h>
#include <linux/tty_driver.h>
#include <linux/tty_flip.h>
#include <linux/module.h>
#include <linux/serial.h>
#include <linux/usb.h>
#include <linux/usb/serial.h>
#include <linux/serial_reg.h>
#include <linux/uaccess.h>
#define QT_OPEN_CLOSE_CHANNEL 0xca
#define QT_SET_GET_DEVICE 0xc2
#define QT_SET_GET_REGISTER 0xc0
#define QT_GET_SET_PREBUF_TRIG_LVL 0xcc
#define QT_SET_ATF 0xcd
#define QT_GET_SET_UART 0xc1
#define QT_TRANSFER_IN 0xc0
#define QT_HW_FLOW_CONTROL_MASK 0xc5
#define QT_SW_FLOW_CONTROL_MASK 0xc6
#define SERIAL_MSR_MASK 0xf0
#define SERIAL_CRTSCTS ((UART_MCR_RTS << 8) | UART_MSR_CTS)
#define SERIAL_EVEN_PARITY (UART_LCR_PARITY | UART_LCR_EPAR)
#define MAX_BAUD_RATE 460800
#define ATC_DISABLED 0x00
#define DUPMODE_BITS 0xc0
#define RR_BITS 0x03
#define LOOPMODE_BITS 0x41
#define RS232_MODE 0x00
#define RTSCTS_TO_CONNECTOR 0x40
#define CLKS_X4 0x02
#define FULLPWRBIT 0x00000080
#define NEXT_BOARD_POWER_BIT 0x00000004
#define DRIVER_DESC "Quatech SSU-100 USB to Serial Driver"
#define USB_VENDOR_ID_QUATECH 0x061d /* Quatech VID */
#define QUATECH_SSU100 0xC020 /* SSU100 */
static const struct usb_device_id id_table[] = {
{USB_DEVICE(USB_VENDOR_ID_QUATECH, QUATECH_SSU100)},
{} /* Terminating entry */
};
MODULE_DEVICE_TABLE(usb, id_table);
struct ssu100_port_private {
spinlock_t status_lock;
u8 shadowLSR;
u8 shadowMSR;
};
static inline int ssu100_control_msg(struct usb_device *dev,
u8 request, u16 data, u16 index)
{
return usb_control_msg(dev, usb_sndctrlpipe(dev, 0),
request, 0x40, data, index,
NULL, 0, 300);
}
static inline int ssu100_setdevice(struct usb_device *dev, u8 *data)
{
u16 x = ((u16)(data[1] << 8) | (u16)(data[0]));
return ssu100_control_msg(dev, QT_SET_GET_DEVICE, x, 0);
}
static inline int ssu100_getdevice(struct usb_device *dev, u8 *data)
{
int ret;
ret = usb_control_msg(dev, usb_rcvctrlpipe(dev, 0),
QT_SET_GET_DEVICE, 0xc0, 0, 0,
data, 3, 300);
if (ret < 3) {
if (ret >= 0)
ret = -EIO;
}
return ret;
}
static inline int ssu100_getregister(struct usb_device *dev,
unsigned short uart,
unsigned short reg,
u8 *data)
{
int ret;
ret = usb_control_msg(dev, usb_rcvctrlpipe(dev, 0),
QT_SET_GET_REGISTER, 0xc0, reg,
uart, data, sizeof(*data), 300);
if (ret < sizeof(*data)) {
if (ret >= 0)
ret = -EIO;
}
return ret;
}
static inline int ssu100_setregister(struct usb_device *dev,
unsigned short uart,
unsigned short reg,
u16 data)
{
u16 value = (data << 8) | reg;
return usb_control_msg(dev, usb_sndctrlpipe(dev, 0),
QT_SET_GET_REGISTER, 0x40, value, uart,
NULL, 0, 300);
}
#define set_mctrl(dev, set) update_mctrl((dev), (set), 0)
#define clear_mctrl(dev, clear) update_mctrl((dev), 0, (clear))
/* these do not deal with device that have more than 1 port */
static inline int update_mctrl(struct usb_device *dev, unsigned int set,
unsigned int clear)
{
unsigned urb_value;
int result;
if (((set | clear) & (TIOCM_DTR | TIOCM_RTS)) == 0) {
dev_dbg(&dev->dev, "%s - DTR|RTS not being set|cleared\n", __func__);
return 0; /* no change */
}
clear &= ~set; /* 'set' takes precedence over 'clear' */
urb_value = 0;
if (set & TIOCM_DTR)
urb_value |= UART_MCR_DTR;
if (set & TIOCM_RTS)
urb_value |= UART_MCR_RTS;
result = ssu100_setregister(dev, 0, UART_MCR, urb_value);
if (result < 0)
dev_dbg(&dev->dev, "%s Error from MODEM_CTRL urb\n", __func__);
return result;
}
static int ssu100_initdevice(struct usb_device *dev)
{
u8 *data;
int result = 0;
data = kzalloc(3, GFP_KERNEL);
if (!data)
return -ENOMEM;
result = ssu100_getdevice(dev, data);
if (result < 0) {
dev_dbg(&dev->dev, "%s - get_device failed %i\n", __func__, result);
goto out;
}
data[1] &= ~FULLPWRBIT;
result = ssu100_setdevice(dev, data);
if (result < 0) {
dev_dbg(&dev->dev, "%s - setdevice failed %i\n", __func__, result);
goto out;
}
result = ssu100_control_msg(dev, QT_GET_SET_PREBUF_TRIG_LVL, 128, 0);
if (result < 0) {
dev_dbg(&dev->dev, "%s - set prebuffer level failed %i\n", __func__, result);
goto out;
}
result = ssu100_control_msg(dev, QT_SET_ATF, ATC_DISABLED, 0);
if (result < 0) {
dev_dbg(&dev->dev, "%s - set ATFprebuffer level failed %i\n", __func__, result);
goto out;
}
result = ssu100_getdevice(dev, data);
if (result < 0) {
dev_dbg(&dev->dev, "%s - get_device failed %i\n", __func__, result);
goto out;
}
data[0] &= ~(RR_BITS | DUPMODE_BITS);
data[0] |= CLKS_X4;
data[1] &= ~(LOOPMODE_BITS);
data[1] |= RS232_MODE;
result = ssu100_setdevice(dev, data);
if (result < 0) {
dev_dbg(&dev->dev, "%s - setdevice failed %i\n", __func__, result);
goto out;
}
out: kfree(data);
return result;
}
static void ssu100_set_termios(struct tty_struct *tty,
struct usb_serial_port *port,
struct ktermios *old_termios)
{
struct usb_device *dev = port->serial->dev;
struct ktermios *termios = &tty->termios;
u16 baud, divisor, remainder;
unsigned int cflag = termios->c_cflag;
u16 urb_value = 0; /* will hold the new flags */
int result;
if (cflag & PARENB) {
if (cflag & PARODD)
urb_value |= UART_LCR_PARITY;
else
urb_value |= SERIAL_EVEN_PARITY;
}
switch (cflag & CSIZE) {
case CS5:
urb_value |= UART_LCR_WLEN5;
break;
case CS6:
urb_value |= UART_LCR_WLEN6;
break;
case CS7:
urb_value |= UART_LCR_WLEN7;
break;
default:
case CS8:
urb_value |= UART_LCR_WLEN8;
break;
}
baud = tty_get_baud_rate(tty);
if (!baud)
baud = 9600;
dev_dbg(&port->dev, "%s - got baud = %d\n", __func__, baud);
divisor = MAX_BAUD_RATE / baud;
remainder = MAX_BAUD_RATE % baud;
if (((remainder * 2) >= baud) && (baud != 110))
divisor++;
urb_value = urb_value << 8;
result = ssu100_control_msg(dev, QT_GET_SET_UART, divisor, urb_value);
if (result < 0)
dev_dbg(&port->dev, "%s - set uart failed\n", __func__);
if (cflag & CRTSCTS)
result = ssu100_control_msg(dev, QT_HW_FLOW_CONTROL_MASK,
SERIAL_CRTSCTS, 0);
else
result = ssu100_control_msg(dev, QT_HW_FLOW_CONTROL_MASK,
0, 0);
if (result < 0)
dev_dbg(&port->dev, "%s - set HW flow control failed\n", __func__);
if (I_IXOFF(tty) || I_IXON(tty)) {
u16 x = ((u16)(START_CHAR(tty) << 8) | (u16)(STOP_CHAR(tty)));
result = ssu100_control_msg(dev, QT_SW_FLOW_CONTROL_MASK,
x, 0);
} else
result = ssu100_control_msg(dev, QT_SW_FLOW_CONTROL_MASK,
0, 0);
if (result < 0)
dev_dbg(&port->dev, "%s - set SW flow control failed\n", __func__);
}
static int ssu100_open(struct tty_struct *tty, struct usb_serial_port *port)
{
struct usb_device *dev = port->serial->dev;
struct ssu100_port_private *priv = usb_get_serial_port_data(port);
u8 *data;
int result;
unsigned long flags;
data = kzalloc(2, GFP_KERNEL);
if (!data)
return -ENOMEM;
result = usb_control_msg(dev, usb_rcvctrlpipe(dev, 0),
QT_OPEN_CLOSE_CHANNEL,
QT_TRANSFER_IN, 0x01,
0, data, 2, 300);
if (result < 2) {
dev_dbg(&port->dev, "%s - open failed %i\n", __func__, result);
if (result >= 0)
result = -EIO;
kfree(data);
return result;
}
spin_lock_irqsave(&priv->status_lock, flags);
priv->shadowLSR = data[0];
priv->shadowMSR = data[1];
spin_unlock_irqrestore(&priv->status_lock, flags);
kfree(data);
/* set to 9600 */
result = ssu100_control_msg(dev, QT_GET_SET_UART, 0x30, 0x0300);
if (result < 0)
dev_dbg(&port->dev, "%s - set uart failed\n", __func__);
if (tty)
ssu100_set_termios(tty, port, &tty->termios);
return usb_serial_generic_open(tty, port);
}
static int get_serial_info(struct usb_serial_port *port,
struct serial_struct __user *retinfo)
{
struct serial_struct tmp;
memset(&tmp, 0, sizeof(tmp));
tmp.line = port->minor;
tmp.port = 0;
tmp.irq = 0;
tmp.xmit_fifo_size = port->bulk_out_size;
tmp.baud_base = 9600;
tmp.close_delay = 5*HZ;
tmp.closing_wait = 30*HZ;
if (copy_to_user(retinfo, &tmp, sizeof(*retinfo)))
return -EFAULT;
return 0;
}
static int ssu100_ioctl(struct tty_struct *tty,
unsigned int cmd, unsigned long arg)
{
struct usb_serial_port *port = tty->driver_data;
switch (cmd) {
case TIOCGSERIAL:
return get_serial_info(port,
(struct serial_struct __user *) arg);
default:
break;
}
return -ENOIOCTLCMD;
}
static int ssu100_attach(struct usb_serial *serial)
{
return ssu100_initdevice(serial->dev);
}
static int ssu100_port_probe(struct usb_serial_port *port)
{
struct ssu100_port_private *priv;
priv = kzalloc(sizeof(*priv), GFP_KERNEL);
if (!priv)
return -ENOMEM;
spin_lock_init(&priv->status_lock);
usb_set_serial_port_data(port, priv);
return 0;
}
static int ssu100_port_remove(struct usb_serial_port *port)
{
struct ssu100_port_private *priv;
priv = usb_get_serial_port_data(port);
kfree(priv);
return 0;
}
static int ssu100_tiocmget(struct tty_struct *tty)
{
struct usb_serial_port *port = tty->driver_data;
struct usb_device *dev = port->serial->dev;
u8 *d;
int r;
d = kzalloc(2, GFP_KERNEL);
if (!d)
return -ENOMEM;
r = ssu100_getregister(dev, 0, UART_MCR, d);
if (r < 0)
goto mget_out;
r = ssu100_getregister(dev, 0, UART_MSR, d+1);
if (r < 0)
goto mget_out;
r = (d[0] & UART_MCR_DTR ? TIOCM_DTR : 0) |
(d[0] & UART_MCR_RTS ? TIOCM_RTS : 0) |
(d[1] & UART_MSR_CTS ? TIOCM_CTS : 0) |
(d[1] & UART_MSR_DCD ? TIOCM_CAR : 0) |
(d[1] & UART_MSR_RI ? TIOCM_RI : 0) |
(d[1] & UART_MSR_DSR ? TIOCM_DSR : 0);
mget_out:
kfree(d);
return r;
}
static int ssu100_tiocmset(struct tty_struct *tty,
unsigned int set, unsigned int clear)
{
struct usb_serial_port *port = tty->driver_data;
struct usb_device *dev = port->serial->dev;
return update_mctrl(dev, set, clear);
}
static void ssu100_dtr_rts(struct usb_serial_port *port, int on)
{
struct usb_device *dev = port->serial->dev;
/* Disable flow control */
if (!on) {
if (ssu100_setregister(dev, 0, UART_MCR, 0) < 0)
dev_err(&port->dev, "error from flowcontrol urb\n");
}
/* drop RTS and DTR */
if (on)
set_mctrl(dev, TIOCM_DTR | TIOCM_RTS);
else
clear_mctrl(dev, TIOCM_DTR | TIOCM_RTS);
}
static void ssu100_update_msr(struct usb_serial_port *port, u8 msr)
{
struct ssu100_port_private *priv = usb_get_serial_port_data(port);
unsigned long flags;
spin_lock_irqsave(&priv->status_lock, flags);
priv->shadowMSR = msr;
spin_unlock_irqrestore(&priv->status_lock, flags);
if (msr & UART_MSR_ANY_DELTA) {
/* update input line counters */
if (msr & UART_MSR_DCTS)
port->icount.cts++;
if (msr & UART_MSR_DDSR)
port->icount.dsr++;
if (msr & UART_MSR_DDCD)
port->icount.dcd++;
if (msr & UART_MSR_TERI)
port->icount.rng++;
wake_up_interruptible(&port->port.delta_msr_wait);
}
}
static void ssu100_update_lsr(struct usb_serial_port *port, u8 lsr,
char *tty_flag)
{
struct ssu100_port_private *priv = usb_get_serial_port_data(port);
unsigned long flags;
spin_lock_irqsave(&priv->status_lock, flags);
priv->shadowLSR = lsr;
spin_unlock_irqrestore(&priv->status_lock, flags);
*tty_flag = TTY_NORMAL;
if (lsr & UART_LSR_BRK_ERROR_BITS) {
/* we always want to update icount, but we only want to
* update tty_flag for one case */
if (lsr & UART_LSR_BI) {
port->icount.brk++;
*tty_flag = TTY_BREAK;
usb_serial_handle_break(port);
}
if (lsr & UART_LSR_PE) {
port->icount.parity++;
if (*tty_flag == TTY_NORMAL)
*tty_flag = TTY_PARITY;
}
if (lsr & UART_LSR_FE) {
port->icount.frame++;
if (*tty_flag == TTY_NORMAL)
*tty_flag = TTY_FRAME;
}
if (lsr & UART_LSR_OE) {
port->icount.overrun++;
tty_insert_flip_char(&port->port, 0, TTY_OVERRUN);
}
}
}
static void ssu100_process_read_urb(struct urb *urb)
{
struct usb_serial_port *port = urb->context;
char *packet = (char *)urb->transfer_buffer;
char flag = TTY_NORMAL;
u32 len = urb->actual_length;
int i;
char *ch;
if ((len >= 4) &&
(packet[0] == 0x1b) && (packet[1] == 0x1b) &&
((packet[2] == 0x00) || (packet[2] == 0x01))) {
if (packet[2] == 0x00)
ssu100_update_lsr(port, packet[3], &flag);
if (packet[2] == 0x01)
ssu100_update_msr(port, packet[3]);
len -= 4;
ch = packet + 4;
} else
ch = packet;
if (!len)
return; /* status only */
if (port->port.console && port->sysrq) {
for (i = 0; i < len; i++, ch++) {
if (!usb_serial_handle_sysrq_char(port, *ch))
tty_insert_flip_char(&port->port, *ch, flag);
}
} else
tty_insert_flip_string_fixed_flag(&port->port, ch, flag, len);
tty_flip_buffer_push(&port->port);
}
static struct usb_serial_driver ssu100_device = {
.driver = {
.owner = THIS_MODULE,
.name = "ssu100",
},
.description = DRIVER_DESC,
.id_table = id_table,
.num_ports = 1,
.open = ssu100_open,
.attach = ssu100_attach,
.port_probe = ssu100_port_probe,
.port_remove = ssu100_port_remove,
.dtr_rts = ssu100_dtr_rts,
.process_read_urb = ssu100_process_read_urb,
.tiocmget = ssu100_tiocmget,
.tiocmset = ssu100_tiocmset,
.tiocmiwait = usb_serial_generic_tiocmiwait,
.get_icount = usb_serial_generic_get_icount,
.ioctl = ssu100_ioctl,
.set_termios = ssu100_set_termios,
};
static struct usb_serial_driver * const serial_drivers[] = {
&ssu100_device, NULL
};
module_usb_serial_driver(serial_drivers, id_table);
MODULE_DESCRIPTION(DRIVER_DESC);
MODULE_LICENSE("GPL v2");