459 lines
17 KiB
C
459 lines
17 KiB
C
/* SPDX-License-Identifier: GPL-2.0-or-later */
|
|
/*
|
|
* ahci.h - Common AHCI SATA definitions and declarations
|
|
*
|
|
* Maintained by: Tejun Heo <tj@kernel.org>
|
|
* Please ALWAYS copy linux-ide@vger.kernel.org
|
|
* on emails.
|
|
*
|
|
* Copyright 2004-2005 Red Hat, Inc.
|
|
*
|
|
* libata documentation is available via 'make {ps|pdf}docs',
|
|
* as Documentation/driver-api/libata.rst
|
|
*
|
|
* AHCI hardware documentation:
|
|
* http://www.intel.com/technology/serialata/pdf/rev1_0.pdf
|
|
* http://www.intel.com/technology/serialata/pdf/rev1_1.pdf
|
|
*/
|
|
|
|
#ifndef _AHCI_H
|
|
#define _AHCI_H
|
|
|
|
#include <linux/pci.h>
|
|
#include <linux/clk.h>
|
|
#include <linux/libata.h>
|
|
#include <linux/phy/phy.h>
|
|
#include <linux/regulator/consumer.h>
|
|
#include <linux/bits.h>
|
|
|
|
/* Enclosure Management Control */
|
|
#define EM_CTRL_MSG_TYPE 0x000f0000
|
|
|
|
/* Enclosure Management LED Message Type */
|
|
#define EM_MSG_LED_HBA_PORT 0x0000000f
|
|
#define EM_MSG_LED_PMP_SLOT 0x0000ff00
|
|
#define EM_MSG_LED_VALUE 0xffff0000
|
|
#define EM_MSG_LED_VALUE_ACTIVITY 0x00070000
|
|
#define EM_MSG_LED_VALUE_OFF 0xfff80000
|
|
#define EM_MSG_LED_VALUE_ON 0x00010000
|
|
|
|
enum {
|
|
AHCI_MAX_PORTS = 32,
|
|
AHCI_MAX_SG = 168, /* hardware max is 64K */
|
|
AHCI_DMA_BOUNDARY = 0xffffffff,
|
|
AHCI_MAX_CMDS = 32,
|
|
AHCI_CMD_SZ = 32,
|
|
AHCI_CMD_SLOT_SZ = AHCI_MAX_CMDS * AHCI_CMD_SZ,
|
|
AHCI_RX_FIS_SZ = 256,
|
|
AHCI_CMD_TBL_CDB = 0x40,
|
|
AHCI_CMD_TBL_HDR_SZ = 0x80,
|
|
AHCI_CMD_TBL_SZ = AHCI_CMD_TBL_HDR_SZ + (AHCI_MAX_SG * 16),
|
|
AHCI_CMD_TBL_AR_SZ = AHCI_CMD_TBL_SZ * AHCI_MAX_CMDS,
|
|
AHCI_PORT_PRIV_DMA_SZ = AHCI_CMD_SLOT_SZ + AHCI_CMD_TBL_AR_SZ +
|
|
AHCI_RX_FIS_SZ,
|
|
AHCI_PORT_PRIV_FBS_DMA_SZ = AHCI_CMD_SLOT_SZ +
|
|
AHCI_CMD_TBL_AR_SZ +
|
|
(AHCI_RX_FIS_SZ * 16),
|
|
AHCI_IRQ_ON_SG = BIT(31),
|
|
AHCI_CMD_ATAPI = BIT(5),
|
|
AHCI_CMD_WRITE = BIT(6),
|
|
AHCI_CMD_PREFETCH = BIT(7),
|
|
AHCI_CMD_RESET = BIT(8),
|
|
AHCI_CMD_CLR_BUSY = BIT(10),
|
|
|
|
RX_FIS_PIO_SETUP = 0x20, /* offset of PIO Setup FIS data */
|
|
RX_FIS_D2H_REG = 0x40, /* offset of D2H Register FIS data */
|
|
RX_FIS_SDB = 0x58, /* offset of SDB FIS data */
|
|
RX_FIS_UNK = 0x60, /* offset of Unknown FIS data */
|
|
|
|
/* global controller registers */
|
|
HOST_CAP = 0x00, /* host capabilities */
|
|
HOST_CTL = 0x04, /* global host control */
|
|
HOST_IRQ_STAT = 0x08, /* interrupt status */
|
|
HOST_PORTS_IMPL = 0x0c, /* bitmap of implemented ports */
|
|
HOST_VERSION = 0x10, /* AHCI spec. version compliancy */
|
|
HOST_EM_LOC = 0x1c, /* Enclosure Management location */
|
|
HOST_EM_CTL = 0x20, /* Enclosure Management Control */
|
|
HOST_CAP2 = 0x24, /* host capabilities, extended */
|
|
|
|
/* HOST_CTL bits */
|
|
HOST_RESET = BIT(0), /* reset controller; self-clear */
|
|
HOST_IRQ_EN = BIT(1), /* global IRQ enable */
|
|
HOST_MRSM = BIT(2), /* MSI Revert to Single Message */
|
|
HOST_AHCI_EN = BIT(31), /* AHCI enabled */
|
|
|
|
/* HOST_CAP bits */
|
|
HOST_CAP_SXS = BIT(5), /* Supports External SATA */
|
|
HOST_CAP_EMS = BIT(6), /* Enclosure Management support */
|
|
HOST_CAP_CCC = BIT(7), /* Command Completion Coalescing */
|
|
HOST_CAP_PART = BIT(13), /* Partial state capable */
|
|
HOST_CAP_SSC = BIT(14), /* Slumber state capable */
|
|
HOST_CAP_PIO_MULTI = BIT(15), /* PIO multiple DRQ support */
|
|
HOST_CAP_FBS = BIT(16), /* FIS-based switching support */
|
|
HOST_CAP_PMP = BIT(17), /* Port Multiplier support */
|
|
HOST_CAP_ONLY = BIT(18), /* Supports AHCI mode only */
|
|
HOST_CAP_CLO = BIT(24), /* Command List Override support */
|
|
HOST_CAP_LED = BIT(25), /* Supports activity LED */
|
|
HOST_CAP_ALPM = BIT(26), /* Aggressive Link PM support */
|
|
HOST_CAP_SSS = BIT(27), /* Staggered Spin-up */
|
|
HOST_CAP_MPS = BIT(28), /* Mechanical presence switch */
|
|
HOST_CAP_SNTF = BIT(29), /* SNotification register */
|
|
HOST_CAP_NCQ = BIT(30), /* Native Command Queueing */
|
|
HOST_CAP_64 = BIT(31), /* PCI DAC (64-bit DMA) support */
|
|
|
|
/* HOST_CAP2 bits */
|
|
HOST_CAP2_BOH = BIT(0), /* BIOS/OS handoff supported */
|
|
HOST_CAP2_NVMHCI = BIT(1), /* NVMHCI supported */
|
|
HOST_CAP2_APST = BIT(2), /* Automatic partial to slumber */
|
|
HOST_CAP2_SDS = BIT(3), /* Support device sleep */
|
|
HOST_CAP2_SADM = BIT(4), /* Support aggressive DevSlp */
|
|
HOST_CAP2_DESO = BIT(5), /* DevSlp from slumber only */
|
|
|
|
/* registers for each SATA port */
|
|
PORT_LST_ADDR = 0x00, /* command list DMA addr */
|
|
PORT_LST_ADDR_HI = 0x04, /* command list DMA addr hi */
|
|
PORT_FIS_ADDR = 0x08, /* FIS rx buf addr */
|
|
PORT_FIS_ADDR_HI = 0x0c, /* FIS rx buf addr hi */
|
|
PORT_IRQ_STAT = 0x10, /* interrupt status */
|
|
PORT_IRQ_MASK = 0x14, /* interrupt enable/disable mask */
|
|
PORT_CMD = 0x18, /* port command */
|
|
PORT_TFDATA = 0x20, /* taskfile data */
|
|
PORT_SIG = 0x24, /* device TF signature */
|
|
PORT_CMD_ISSUE = 0x38, /* command issue */
|
|
PORT_SCR_STAT = 0x28, /* SATA phy register: SStatus */
|
|
PORT_SCR_CTL = 0x2c, /* SATA phy register: SControl */
|
|
PORT_SCR_ERR = 0x30, /* SATA phy register: SError */
|
|
PORT_SCR_ACT = 0x34, /* SATA phy register: SActive */
|
|
PORT_SCR_NTF = 0x3c, /* SATA phy register: SNotification */
|
|
PORT_FBS = 0x40, /* FIS-based Switching */
|
|
PORT_DEVSLP = 0x44, /* device sleep */
|
|
|
|
/* PORT_IRQ_{STAT,MASK} bits */
|
|
PORT_IRQ_COLD_PRES = BIT(31), /* cold presence detect */
|
|
PORT_IRQ_TF_ERR = BIT(30), /* task file error */
|
|
PORT_IRQ_HBUS_ERR = BIT(29), /* host bus fatal error */
|
|
PORT_IRQ_HBUS_DATA_ERR = BIT(28), /* host bus data error */
|
|
PORT_IRQ_IF_ERR = BIT(27), /* interface fatal error */
|
|
PORT_IRQ_IF_NONFATAL = BIT(26), /* interface non-fatal error */
|
|
PORT_IRQ_OVERFLOW = BIT(24), /* xfer exhausted available S/G */
|
|
PORT_IRQ_BAD_PMP = BIT(23), /* incorrect port multiplier */
|
|
|
|
PORT_IRQ_PHYRDY = BIT(22), /* PhyRdy changed */
|
|
PORT_IRQ_DMPS = BIT(7), /* mechanical presence status */
|
|
PORT_IRQ_CONNECT = BIT(6), /* port connect change status */
|
|
PORT_IRQ_SG_DONE = BIT(5), /* descriptor processed */
|
|
PORT_IRQ_UNK_FIS = BIT(4), /* unknown FIS rx'd */
|
|
PORT_IRQ_SDB_FIS = BIT(3), /* Set Device Bits FIS rx'd */
|
|
PORT_IRQ_DMAS_FIS = BIT(2), /* DMA Setup FIS rx'd */
|
|
PORT_IRQ_PIOS_FIS = BIT(1), /* PIO Setup FIS rx'd */
|
|
PORT_IRQ_D2H_REG_FIS = BIT(0), /* D2H Register FIS rx'd */
|
|
|
|
PORT_IRQ_FREEZE = PORT_IRQ_HBUS_ERR |
|
|
PORT_IRQ_IF_ERR |
|
|
PORT_IRQ_CONNECT |
|
|
PORT_IRQ_PHYRDY |
|
|
PORT_IRQ_UNK_FIS |
|
|
PORT_IRQ_BAD_PMP,
|
|
PORT_IRQ_ERROR = PORT_IRQ_FREEZE |
|
|
PORT_IRQ_TF_ERR |
|
|
PORT_IRQ_HBUS_DATA_ERR,
|
|
DEF_PORT_IRQ = PORT_IRQ_ERROR | PORT_IRQ_SG_DONE |
|
|
PORT_IRQ_SDB_FIS | PORT_IRQ_DMAS_FIS |
|
|
PORT_IRQ_PIOS_FIS | PORT_IRQ_D2H_REG_FIS,
|
|
|
|
/* PORT_CMD bits */
|
|
PORT_CMD_ASP = BIT(27), /* Aggressive Slumber/Partial */
|
|
PORT_CMD_ALPE = BIT(26), /* Aggressive Link PM enable */
|
|
PORT_CMD_ATAPI = BIT(24), /* Device is ATAPI */
|
|
PORT_CMD_FBSCP = BIT(22), /* FBS Capable Port */
|
|
PORT_CMD_ESP = BIT(21), /* External Sata Port */
|
|
PORT_CMD_CPD = BIT(20), /* Cold Presence Detection */
|
|
PORT_CMD_MPSP = BIT(19), /* Mechanical Presence Switch */
|
|
PORT_CMD_HPCP = BIT(18), /* HotPlug Capable Port */
|
|
PORT_CMD_PMP = BIT(17), /* PMP attached */
|
|
PORT_CMD_LIST_ON = BIT(15), /* cmd list DMA engine running */
|
|
PORT_CMD_FIS_ON = BIT(14), /* FIS DMA engine running */
|
|
PORT_CMD_FIS_RX = BIT(4), /* Enable FIS receive DMA engine */
|
|
PORT_CMD_CLO = BIT(3), /* Command list override */
|
|
PORT_CMD_POWER_ON = BIT(2), /* Power up device */
|
|
PORT_CMD_SPIN_UP = BIT(1), /* Spin up device */
|
|
PORT_CMD_START = BIT(0), /* Enable port DMA engine */
|
|
|
|
PORT_CMD_ICC_MASK = (0xfu << 28), /* i/f ICC state mask */
|
|
PORT_CMD_ICC_ACTIVE = (0x1u << 28), /* Put i/f in active state */
|
|
PORT_CMD_ICC_PARTIAL = (0x2u << 28), /* Put i/f in partial state */
|
|
PORT_CMD_ICC_SLUMBER = (0x6u << 28), /* Put i/f in slumber state */
|
|
|
|
/* PORT_CMD capabilities mask */
|
|
PORT_CMD_CAP = PORT_CMD_HPCP | PORT_CMD_MPSP |
|
|
PORT_CMD_CPD | PORT_CMD_ESP | PORT_CMD_FBSCP,
|
|
|
|
/* PORT_FBS bits */
|
|
PORT_FBS_DWE_OFFSET = 16, /* FBS device with error offset */
|
|
PORT_FBS_ADO_OFFSET = 12, /* FBS active dev optimization offset */
|
|
PORT_FBS_DEV_OFFSET = 8, /* FBS device to issue offset */
|
|
PORT_FBS_DEV_MASK = (0xf << PORT_FBS_DEV_OFFSET), /* FBS.DEV */
|
|
PORT_FBS_SDE = BIT(2), /* FBS single device error */
|
|
PORT_FBS_DEC = BIT(1), /* FBS device error clear */
|
|
PORT_FBS_EN = BIT(0), /* Enable FBS */
|
|
|
|
/* PORT_DEVSLP bits */
|
|
PORT_DEVSLP_DM_OFFSET = 25, /* DITO multiplier offset */
|
|
PORT_DEVSLP_DM_MASK = (0xf << 25), /* DITO multiplier mask */
|
|
PORT_DEVSLP_DITO_OFFSET = 15, /* DITO offset */
|
|
PORT_DEVSLP_MDAT_OFFSET = 10, /* Minimum assertion time */
|
|
PORT_DEVSLP_DETO_OFFSET = 2, /* DevSlp exit timeout */
|
|
PORT_DEVSLP_DSP = BIT(1), /* DevSlp present */
|
|
PORT_DEVSLP_ADSE = BIT(0), /* Aggressive DevSlp enable */
|
|
|
|
/* hpriv->flags bits */
|
|
|
|
#define AHCI_HFLAGS(flags) .private_data = (void *)(flags)
|
|
|
|
AHCI_HFLAG_NO_NCQ = BIT(0),
|
|
AHCI_HFLAG_IGN_IRQ_IF_ERR = BIT(1), /* ignore IRQ_IF_ERR */
|
|
AHCI_HFLAG_IGN_SERR_INTERNAL = BIT(2), /* ignore SERR_INTERNAL */
|
|
AHCI_HFLAG_32BIT_ONLY = BIT(3), /* force 32bit */
|
|
AHCI_HFLAG_MV_PATA = BIT(4), /* PATA port */
|
|
AHCI_HFLAG_NO_MSI = BIT(5), /* no PCI MSI */
|
|
AHCI_HFLAG_NO_PMP = BIT(6), /* no PMP */
|
|
AHCI_HFLAG_SECT255 = BIT(8), /* max 255 sectors */
|
|
AHCI_HFLAG_YES_NCQ = BIT(9), /* force NCQ cap on */
|
|
AHCI_HFLAG_NO_SUSPEND = BIT(10), /* don't suspend */
|
|
AHCI_HFLAG_SRST_TOUT_IS_OFFLINE = BIT(11), /* treat SRST timeout as
|
|
link offline */
|
|
AHCI_HFLAG_NO_SNTF = BIT(12), /* no sntf */
|
|
AHCI_HFLAG_NO_FPDMA_AA = BIT(13), /* no FPDMA AA */
|
|
AHCI_HFLAG_YES_FBS = BIT(14), /* force FBS cap on */
|
|
AHCI_HFLAG_DELAY_ENGINE = BIT(15), /* do not start engine on
|
|
port start (wait until
|
|
error-handling stage) */
|
|
AHCI_HFLAG_NO_DEVSLP = BIT(17), /* no device sleep */
|
|
AHCI_HFLAG_NO_FBS = BIT(18), /* no FBS */
|
|
|
|
#ifdef CONFIG_PCI_MSI
|
|
AHCI_HFLAG_MULTI_MSI = BIT(20), /* per-port MSI(-X) */
|
|
#else
|
|
/* compile out MSI infrastructure */
|
|
AHCI_HFLAG_MULTI_MSI = 0,
|
|
#endif
|
|
AHCI_HFLAG_WAKE_BEFORE_STOP = BIT(22), /* wake before DMA stop */
|
|
AHCI_HFLAG_YES_ALPM = BIT(23), /* force ALPM cap on */
|
|
AHCI_HFLAG_NO_WRITE_TO_RO = BIT(24), /* don't write to read
|
|
only registers */
|
|
AHCI_HFLAG_USE_LPM_POLICY = BIT(25), /* chipset that should use
|
|
SATA_MOBILE_LPM_POLICY
|
|
as default lpm_policy */
|
|
AHCI_HFLAG_SUSPEND_PHYS = BIT(26), /* handle PHYs during
|
|
suspend/resume */
|
|
AHCI_HFLAG_NO_SXS = BIT(28), /* SXS not supported */
|
|
AHCI_HFLAG_43BIT_ONLY = BIT(29), /* 43bit DMA addr limit */
|
|
|
|
/* ap->flags bits */
|
|
|
|
AHCI_FLAG_COMMON = ATA_FLAG_SATA | ATA_FLAG_PIO_DMA |
|
|
ATA_FLAG_ACPI_SATA | ATA_FLAG_AN,
|
|
|
|
ICH_MAP = 0x90, /* ICH MAP register */
|
|
PCS_6 = 0x92, /* 6 port PCS */
|
|
PCS_7 = 0x94, /* 7+ port PCS (Denverton) */
|
|
|
|
/* em constants */
|
|
EM_MAX_SLOTS = SATA_PMP_MAX_PORTS,
|
|
EM_MAX_RETRY = 5,
|
|
|
|
/* em_ctl bits */
|
|
EM_CTL_RST = BIT(9), /* Reset */
|
|
EM_CTL_TM = BIT(8), /* Transmit Message */
|
|
EM_CTL_MR = BIT(0), /* Message Received */
|
|
EM_CTL_ALHD = BIT(26), /* Activity LED */
|
|
EM_CTL_XMT = BIT(25), /* Transmit Only */
|
|
EM_CTL_SMB = BIT(24), /* Single Message Buffer */
|
|
EM_CTL_SGPIO = BIT(19), /* SGPIO messages supported */
|
|
EM_CTL_SES = BIT(18), /* SES-2 messages supported */
|
|
EM_CTL_SAFTE = BIT(17), /* SAF-TE messages supported */
|
|
EM_CTL_LED = BIT(16), /* LED messages supported */
|
|
|
|
/* em message type */
|
|
EM_MSG_TYPE_LED = BIT(0), /* LED */
|
|
EM_MSG_TYPE_SAFTE = BIT(1), /* SAF-TE */
|
|
EM_MSG_TYPE_SES2 = BIT(2), /* SES-2 */
|
|
EM_MSG_TYPE_SGPIO = BIT(3), /* SGPIO */
|
|
};
|
|
|
|
struct ahci_cmd_hdr {
|
|
__le32 opts;
|
|
__le32 status;
|
|
__le32 tbl_addr;
|
|
__le32 tbl_addr_hi;
|
|
__le32 reserved[4];
|
|
};
|
|
|
|
struct ahci_sg {
|
|
__le32 addr;
|
|
__le32 addr_hi;
|
|
__le32 reserved;
|
|
__le32 flags_size;
|
|
};
|
|
|
|
struct ahci_em_priv {
|
|
enum sw_activity blink_policy;
|
|
struct timer_list timer;
|
|
unsigned long saved_activity;
|
|
unsigned long activity;
|
|
unsigned long led_state;
|
|
struct ata_link *link;
|
|
};
|
|
|
|
struct ahci_port_priv {
|
|
struct ata_link *active_link;
|
|
struct ahci_cmd_hdr *cmd_slot;
|
|
dma_addr_t cmd_slot_dma;
|
|
void *cmd_tbl;
|
|
dma_addr_t cmd_tbl_dma;
|
|
void *rx_fis;
|
|
dma_addr_t rx_fis_dma;
|
|
/* for NCQ spurious interrupt analysis */
|
|
unsigned int ncq_saw_d2h:1;
|
|
unsigned int ncq_saw_dmas:1;
|
|
unsigned int ncq_saw_sdb:1;
|
|
spinlock_t lock; /* protects parent ata_port */
|
|
u32 intr_mask; /* interrupts to enable */
|
|
bool fbs_supported; /* set iff FBS is supported */
|
|
bool fbs_enabled; /* set iff FBS is enabled */
|
|
int fbs_last_dev; /* save FBS.DEV of last FIS */
|
|
/* enclosure management info per PM slot */
|
|
struct ahci_em_priv em_priv[EM_MAX_SLOTS];
|
|
char *irq_desc; /* desc in /proc/interrupts */
|
|
};
|
|
|
|
struct ahci_host_priv {
|
|
/* Input fields */
|
|
unsigned int flags; /* AHCI_HFLAG_* */
|
|
u32 mask_port_map; /* mask out particular bits */
|
|
|
|
void __iomem * mmio; /* bus-independent mem map */
|
|
u32 cap; /* cap to use */
|
|
u32 cap2; /* cap2 to use */
|
|
u32 version; /* cached version */
|
|
u32 port_map; /* port map to use */
|
|
u32 saved_cap; /* saved initial cap */
|
|
u32 saved_cap2; /* saved initial cap2 */
|
|
u32 saved_port_map; /* saved initial port_map */
|
|
u32 saved_port_cap[AHCI_MAX_PORTS]; /* saved port_cap */
|
|
u32 em_loc; /* enclosure management location */
|
|
u32 em_buf_sz; /* EM buffer size in byte */
|
|
u32 em_msg_type; /* EM message type */
|
|
u32 remapped_nvme; /* NVMe remapped device count */
|
|
bool got_runtime_pm; /* Did we do pm_runtime_get? */
|
|
unsigned int n_clks;
|
|
struct clk_bulk_data *clks; /* Optional */
|
|
unsigned int f_rsts;
|
|
struct reset_control *rsts; /* Optional */
|
|
struct regulator **target_pwrs; /* Optional */
|
|
struct regulator *ahci_regulator;/* Optional */
|
|
struct regulator *phy_regulator;/* Optional */
|
|
/*
|
|
* If platform uses PHYs. There is a 1:1 relation between the port number and
|
|
* the PHY position in this array.
|
|
*/
|
|
struct phy **phys;
|
|
unsigned nports; /* Number of ports */
|
|
void *plat_data; /* Other platform data */
|
|
unsigned int irq; /* interrupt line */
|
|
/*
|
|
* Optional ahci_start_engine override, if not set this gets set to the
|
|
* default ahci_start_engine during ahci_save_initial_config, this can
|
|
* be overridden anytime before the host is activated.
|
|
*/
|
|
void (*start_engine)(struct ata_port *ap);
|
|
/*
|
|
* Optional ahci_stop_engine override, if not set this gets set to the
|
|
* default ahci_stop_engine during ahci_save_initial_config, this can
|
|
* be overridden anytime before the host is activated.
|
|
*/
|
|
int (*stop_engine)(struct ata_port *ap);
|
|
|
|
irqreturn_t (*irq_handler)(int irq, void *dev_instance);
|
|
|
|
/* only required for per-port MSI(-X) support */
|
|
int (*get_irq_vector)(struct ata_host *host,
|
|
int port);
|
|
};
|
|
|
|
extern int ahci_ignore_sss;
|
|
|
|
extern const struct attribute_group *ahci_shost_groups[];
|
|
extern const struct attribute_group *ahci_sdev_groups[];
|
|
|
|
/*
|
|
* This must be instantiated by the edge drivers. Read the comments
|
|
* for ATA_BASE_SHT
|
|
*/
|
|
#define AHCI_SHT(drv_name) \
|
|
__ATA_BASE_SHT(drv_name), \
|
|
.can_queue = AHCI_MAX_CMDS, \
|
|
.sg_tablesize = AHCI_MAX_SG, \
|
|
.dma_boundary = AHCI_DMA_BOUNDARY, \
|
|
.shost_groups = ahci_shost_groups, \
|
|
.sdev_groups = ahci_sdev_groups, \
|
|
.change_queue_depth = ata_scsi_change_queue_depth, \
|
|
.tag_alloc_policy = BLK_TAG_ALLOC_RR, \
|
|
.slave_configure = ata_scsi_slave_config
|
|
|
|
extern struct ata_port_operations ahci_ops;
|
|
extern struct ata_port_operations ahci_platform_ops;
|
|
extern struct ata_port_operations ahci_pmp_retry_srst_ops;
|
|
|
|
unsigned int ahci_dev_classify(struct ata_port *ap);
|
|
void ahci_fill_cmd_slot(struct ahci_port_priv *pp, unsigned int tag,
|
|
u32 opts);
|
|
void ahci_save_initial_config(struct device *dev,
|
|
struct ahci_host_priv *hpriv);
|
|
void ahci_init_controller(struct ata_host *host);
|
|
int ahci_reset_controller(struct ata_host *host);
|
|
|
|
int ahci_do_softreset(struct ata_link *link, unsigned int *class,
|
|
int pmp, unsigned long deadline,
|
|
int (*check_ready)(struct ata_link *link));
|
|
|
|
int ahci_do_hardreset(struct ata_link *link, unsigned int *class,
|
|
unsigned long deadline, bool *online);
|
|
|
|
unsigned int ahci_qc_issue(struct ata_queued_cmd *qc);
|
|
int ahci_stop_engine(struct ata_port *ap);
|
|
void ahci_start_fis_rx(struct ata_port *ap);
|
|
void ahci_start_engine(struct ata_port *ap);
|
|
int ahci_check_ready(struct ata_link *link);
|
|
int ahci_kick_engine(struct ata_port *ap);
|
|
int ahci_port_resume(struct ata_port *ap);
|
|
void ahci_set_em_messages(struct ahci_host_priv *hpriv,
|
|
struct ata_port_info *pi);
|
|
int ahci_reset_em(struct ata_host *host);
|
|
void ahci_print_info(struct ata_host *host, const char *scc_s);
|
|
int ahci_host_activate(struct ata_host *host, const struct scsi_host_template *sht);
|
|
void ahci_error_handler(struct ata_port *ap);
|
|
u32 ahci_handle_port_intr(struct ata_host *host, u32 irq_masked);
|
|
|
|
static inline void __iomem *__ahci_port_base(struct ahci_host_priv *hpriv,
|
|
unsigned int port_no)
|
|
{
|
|
void __iomem *mmio = hpriv->mmio;
|
|
|
|
return mmio + 0x100 + (port_no * 0x80);
|
|
}
|
|
|
|
static inline void __iomem *ahci_port_base(struct ata_port *ap)
|
|
{
|
|
struct ahci_host_priv *hpriv = ap->host->private_data;
|
|
|
|
return __ahci_port_base(hpriv, ap->port_no);
|
|
}
|
|
|
|
static inline int ahci_nr_ports(u32 cap)
|
|
{
|
|
return (cap & 0x1f) + 1;
|
|
}
|
|
|
|
#endif /* _AHCI_H */
|