105 lines
3.0 KiB
Plaintext
105 lines
3.0 KiB
Plaintext
Qualcomm Shared Memory Point 2 Point binding
|
|
|
|
The Shared Memory Point to Point (SMP2P) protocol facilitates communication of
|
|
a single 32-bit value between two processors. Each value has a single writer
|
|
(the local side) and a single reader (the remote side). Values are uniquely
|
|
identified in the system by the directed edge (local processor ID to remote
|
|
processor ID) and a string identifier.
|
|
|
|
- compatible:
|
|
Usage: required
|
|
Value type: <string>
|
|
Definition: must be one of:
|
|
"qcom,smp2p"
|
|
|
|
- interrupts:
|
|
Usage: required
|
|
Value type: <prop-encoded-array>
|
|
Definition: one entry specifying the smp2p notification interrupt
|
|
|
|
- qcom,ipc:
|
|
Usage: required
|
|
Value type: <prop-encoded-array>
|
|
Definition: three entries specifying the outgoing ipc bit used for
|
|
signaling the remote end of the smp2p edge:
|
|
- phandle to a syscon node representing the apcs registers
|
|
- u32 representing offset to the register within the syscon
|
|
- u32 representing the ipc bit within the register
|
|
|
|
- qcom,smem:
|
|
Usage: required
|
|
Value type: <u32 array>
|
|
Definition: two identifiers of the inbound and outbound smem items used
|
|
for this edge
|
|
|
|
- qcom,local-pid:
|
|
Usage: required
|
|
Value type: <u32>
|
|
Definition: specifies the identfier of the local endpoint of this edge
|
|
|
|
- qcom,remote-pid:
|
|
Usage: required
|
|
Value type: <u32>
|
|
Definition: specifies the identfier of the remote endpoint of this edge
|
|
|
|
= SUBNODES
|
|
Each SMP2P pair contain a set of inbound and outbound entries, these are
|
|
described in subnodes of the smp2p device node. The node names are not
|
|
important.
|
|
|
|
- qcom,entry-name:
|
|
Usage: required
|
|
Value type: <string>
|
|
Definition: specifies the name of this entry, for inbound entries this
|
|
will be used to match against the remotely allocated entry
|
|
and for outbound entries this name is used for allocating
|
|
entries
|
|
|
|
- interrupt-controller:
|
|
Usage: required for incoming entries
|
|
Value type: <empty>
|
|
Definition: marks the entry as inbound; the node should be specified
|
|
as a two cell interrupt-controller as defined in
|
|
"../interrupt-controller/interrupts.txt"
|
|
If not specified this node will denote the outgoing entry
|
|
|
|
- #interrupt-cells:
|
|
Usage: required for incoming entries
|
|
Value type: <u32>
|
|
Definition: must be 2 - denoting the bit in the entry and IRQ flags
|
|
|
|
- #qcom,smem-state-cells:
|
|
Usage: required for outgoing entries
|
|
Value type: <u32>
|
|
Definition: must be 1 - denoting the bit in the entry
|
|
|
|
= EXAMPLE
|
|
The following example shows the SMP2P setup with the wireless processor,
|
|
defined from the 8974 apps processor's point-of-view. It encompasses one
|
|
inbound and one outbound entry:
|
|
|
|
wcnss-smp2p {
|
|
compatible = "qcom,smp2p";
|
|
qcom,smem = <431>, <451>;
|
|
|
|
interrupts = <0 143 1>;
|
|
|
|
qcom,ipc = <&apcs 8 18>;
|
|
|
|
qcom,local-pid = <0>;
|
|
qcom,remote-pid = <4>;
|
|
|
|
wcnss_smp2p_out: master-kernel {
|
|
qcom,entry-name = "master-kernel";
|
|
|
|
#qcom,smem-state-cells = <1>;
|
|
};
|
|
|
|
wcnss_smp2p_in: slave-kernel {
|
|
qcom,entry-name = "slave-kernel";
|
|
|
|
interrupt-controller;
|
|
#interrupt-cells = <2>;
|
|
};
|
|
};
|