138 lines
3.9 KiB
Plaintext
138 lines
3.9 KiB
Plaintext
* Device tree bindings for Atmel EBI
|
|
|
|
The External Bus Interface (EBI) controller is a bus where you can connect
|
|
asynchronous (NAND, NOR, SRAM, ....) and synchronous memories (SDR/DDR SDRAMs).
|
|
The EBI provides a glue-less interface to asynchronous memories through the SMC
|
|
(Static Memory Controller).
|
|
|
|
Required properties:
|
|
|
|
- compatible: "atmel,at91sam9260-ebi"
|
|
"atmel,at91sam9261-ebi"
|
|
"atmel,at91sam9263-ebi0"
|
|
"atmel,at91sam9263-ebi1"
|
|
"atmel,at91sam9rl-ebi"
|
|
"atmel,at91sam9g45-ebi"
|
|
"atmel,at91sam9x5-ebi"
|
|
"atmel,sama5d3-ebi"
|
|
"microchip,sam9x60-ebi"
|
|
|
|
- reg: Contains offset/length value for EBI memory mapping.
|
|
This property might contain several entries if the EBI
|
|
memory range is not contiguous
|
|
|
|
- #address-cells: Must be 2.
|
|
The first cell encodes the CS.
|
|
The second cell encode the offset into the CS memory
|
|
range.
|
|
|
|
- #size-cells: Must be set to 1.
|
|
|
|
- ranges: Encodes CS to memory region association.
|
|
|
|
- clocks: Clock feeding the EBI controller.
|
|
See clock-bindings.txt
|
|
|
|
Children device nodes are representing device connected to the EBI bus.
|
|
|
|
Required device node properties:
|
|
|
|
- reg: Contains the chip-select id, the offset and the length
|
|
of the memory region requested by the device.
|
|
|
|
EBI bus configuration will be defined directly in the device subnode.
|
|
|
|
Optional EBI/SMC properties:
|
|
|
|
- atmel,smc-bus-width: width of the asynchronous device's data bus
|
|
8, 16 or 32.
|
|
Default to 8 when undefined.
|
|
|
|
- atmel,smc-byte-access-type "write" or "select" (see Atmel datasheet).
|
|
Default to "select" when undefined.
|
|
|
|
- atmel,smc-read-mode "nrd" or "ncs".
|
|
Default to "ncs" when undefined.
|
|
|
|
- atmel,smc-write-mode "nwe" or "ncs".
|
|
Default to "ncs" when undefined.
|
|
|
|
- atmel,smc-exnw-mode "disabled", "frozen" or "ready".
|
|
Default to "disabled" when undefined.
|
|
|
|
- atmel,smc-page-mode enable page mode if present. The provided value
|
|
defines the page size (supported values: 4, 8,
|
|
16 and 32).
|
|
|
|
- atmel,smc-tdf-mode: "normal" or "optimized". When set to
|
|
"optimized" the data float time is optimized
|
|
depending on the next device being accessed
|
|
(next device setup time is subtracted to the
|
|
current device data float time).
|
|
Default to "normal" when undefined.
|
|
|
|
If at least one atmel,smc- property is defined the following SMC timing
|
|
properties become mandatory. In the other hand, if none of the atmel,smc-
|
|
properties are specified, we assume that the EBI bus configuration will be
|
|
handled by the sub-device driver, and none of those properties should be
|
|
defined.
|
|
|
|
All the timings are expressed in nanoseconds (see Atmel datasheet for a full
|
|
description).
|
|
|
|
- atmel,smc-ncs-rd-setup-ns
|
|
- atmel,smc-nrd-setup-ns
|
|
- atmel,smc-ncs-wr-setup-ns
|
|
- atmel,smc-nwe-setup-ns
|
|
- atmel,smc-ncs-rd-pulse-ns
|
|
- atmel,smc-nrd-pulse-ns
|
|
- atmel,smc-ncs-wr-pulse-ns
|
|
- atmel,smc-nwe-pulse-ns
|
|
- atmel,smc-nwe-cycle-ns
|
|
- atmel,smc-nrd-cycle-ns
|
|
- atmel,smc-tdf-ns
|
|
|
|
Example:
|
|
|
|
ebi: ebi@10000000 {
|
|
compatible = "atmel,sama5d3-ebi";
|
|
#address-cells = <2>;
|
|
#size-cells = <1>;
|
|
atmel,smc = <&hsmc>;
|
|
atmel,matrix = <&matrix>;
|
|
reg = <0x10000000 0x10000000
|
|
0x40000000 0x30000000>;
|
|
ranges = <0x0 0x0 0x10000000 0x10000000
|
|
0x1 0x0 0x40000000 0x10000000
|
|
0x2 0x0 0x50000000 0x10000000
|
|
0x3 0x0 0x60000000 0x10000000>;
|
|
clocks = <&mck>;
|
|
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&pinctrl_ebi_addr>;
|
|
|
|
nor: flash@0,0 {
|
|
compatible = "cfi-flash";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
reg = <0x0 0x0 0x1000000>;
|
|
bank-width = <2>;
|
|
|
|
atmel,smc-read-mode = "nrd";
|
|
atmel,smc-write-mode = "nwe";
|
|
atmel,smc-bus-width = <16>;
|
|
atmel,smc-ncs-rd-setup-ns = <0>;
|
|
atmel,smc-ncs-wr-setup-ns = <0>;
|
|
atmel,smc-nwe-setup-ns = <8>;
|
|
atmel,smc-nrd-setup-ns = <16>;
|
|
atmel,smc-ncs-rd-pulse-ns = <84>;
|
|
atmel,smc-ncs-wr-pulse-ns = <84>;
|
|
atmel,smc-nrd-pulse-ns = <76>;
|
|
atmel,smc-nwe-pulse-ns = <76>;
|
|
atmel,smc-nrd-cycle-ns = <107>;
|
|
atmel,smc-nwe-cycle-ns = <84>;
|
|
atmel,smc-tdf-ns = <16>;
|
|
};
|
|
};
|
|
|