121 lines
4.4 KiB
Plaintext
121 lines
4.4 KiB
Plaintext
MT8173 xHCI
|
|
|
|
The device node for Mediatek SOC USB3.0 host controller
|
|
|
|
There are two scenarios: the first one only supports xHCI driver;
|
|
the second one supports dual-role mode, and the host is based on xHCI
|
|
driver. Take account of backward compatibility, we divide bindings
|
|
into two parts.
|
|
|
|
1st: only supports xHCI driver
|
|
------------------------------------------------------------------------
|
|
|
|
Required properties:
|
|
- compatible : should be "mediatek,<soc-model>-xhci", "mediatek,mtk-xhci",
|
|
soc-model is the name of SoC, such as mt8173, mt2712 etc, when using
|
|
"mediatek,mtk-xhci" compatible string, you need SoC specific ones in
|
|
addition, one of:
|
|
- "mediatek,mt8173-xhci"
|
|
- reg : specifies physical base address and size of the registers
|
|
- reg-names: should be "mac" for xHCI MAC and "ippc" for IP port control
|
|
- interrupts : interrupt used by the controller
|
|
- power-domains : a phandle to USB power domain node to control USB's
|
|
mtcmos
|
|
- vusb33-supply : regulator of USB avdd3.3v
|
|
|
|
- clocks : a list of phandle + clock-specifier pairs, one for each
|
|
entry in clock-names
|
|
- clock-names : must contain
|
|
"sys_ck": controller clock used by normal mode,
|
|
the following ones are optional:
|
|
"ref_ck": reference clock used by low power mode etc,
|
|
"mcu_ck": mcu_bus clock for register access,
|
|
"dma_ck": dma_bus clock for data transfer by DMA
|
|
|
|
- phys : see usb-hcd.txt in the current directory
|
|
|
|
Optional properties:
|
|
- wakeup-source : enable USB remote wakeup;
|
|
- mediatek,syscon-wakeup : phandle to syscon used to access the register
|
|
of the USB wakeup glue layer between xHCI and SPM; it depends on
|
|
"wakeup-source", and has two arguments:
|
|
- the first one : register base address of the glue layer in syscon;
|
|
- the second one : hardware version of the glue layer
|
|
- 1 : used by mt8173 etc
|
|
- 2 : used by mt2712 etc
|
|
- mediatek,u3p-dis-msk : mask to disable u3ports, bit0 for u3port0,
|
|
bit1 for u3port1, ... etc;
|
|
- vbus-supply : reference to the VBUS regulator;
|
|
- usb3-lpm-capable : supports USB3.0 LPM
|
|
- pinctrl-names : a pinctrl state named "default" must be defined
|
|
- pinctrl-0 : pin control group
|
|
See: Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt
|
|
- imod-interval-ns: default interrupt moderation interval is 5000ns
|
|
|
|
additionally the properties from usb-hcd.txt (in the current directory) are
|
|
supported.
|
|
|
|
Example:
|
|
usb30: usb@11270000 {
|
|
compatible = "mediatek,mt8173-xhci";
|
|
reg = <0 0x11270000 0 0x1000>,
|
|
<0 0x11280700 0 0x0100>;
|
|
reg-names = "mac", "ippc";
|
|
interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_LOW>;
|
|
power-domains = <&scpsys MT8173_POWER_DOMAIN_USB>;
|
|
clocks = <&topckgen CLK_TOP_USB30_SEL>, <&clk26m>,
|
|
<&pericfg CLK_PERI_USB0>,
|
|
<&pericfg CLK_PERI_USB1>;
|
|
clock-names = "sys_ck", "ref_ck";
|
|
phys = <&phy_port0 PHY_TYPE_USB3>,
|
|
<&phy_port1 PHY_TYPE_USB2>;
|
|
vusb33-supply = <&mt6397_vusb_reg>;
|
|
vbus-supply = <&usb_p1_vbus>;
|
|
usb3-lpm-capable;
|
|
mediatek,syscon-wakeup = <&pericfg 0x400 1>;
|
|
wakeup-source;
|
|
imod-interval-ns = <10000>;
|
|
};
|
|
|
|
2nd: dual-role mode with xHCI driver
|
|
------------------------------------------------------------------------
|
|
|
|
In the case, xhci is added as subnode to mtu3. An example and the DT binding
|
|
details of mtu3 can be found in:
|
|
Documentation/devicetree/bindings/usb/mediatek,mtu3.txt
|
|
|
|
Required properties:
|
|
- compatible : should be "mediatek,<soc-model>-xhci", "mediatek,mtk-xhci",
|
|
soc-model is the name of SoC, such as mt8173, mt2712 etc, when using
|
|
"mediatek,mtk-xhci" compatible string, you need SoC specific ones in
|
|
addition, one of:
|
|
- "mediatek,mt8173-xhci"
|
|
- reg : specifies physical base address and size of the registers
|
|
- reg-names: should be "mac" for xHCI MAC
|
|
- interrupts : interrupt used by the host controller
|
|
- power-domains : a phandle to USB power domain node to control USB's
|
|
mtcmos
|
|
- vusb33-supply : regulator of USB avdd3.3v
|
|
|
|
- clocks : a list of phandle + clock-specifier pairs, one for each
|
|
entry in clock-names
|
|
- clock-names : must contain "sys_ck", and the following ones are optional:
|
|
"ref_ck", "mcu_ck" and "dma_ck"
|
|
|
|
Optional properties:
|
|
- vbus-supply : reference to the VBUS regulator;
|
|
- usb3-lpm-capable : supports USB3.0 LPM
|
|
|
|
Example:
|
|
usb30: usb@11270000 {
|
|
compatible = "mediatek,mt8173-xhci";
|
|
reg = <0 0x11270000 0 0x1000>;
|
|
reg-names = "mac";
|
|
interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_LOW>;
|
|
power-domains = <&scpsys MT8173_POWER_DOMAIN_USB>;
|
|
clocks = <&topckgen CLK_TOP_USB30_SEL>, <&clk26m>;
|
|
clock-names = "sys_ck", "ref_ck";
|
|
vusb33-supply = <&mt6397_vusb_reg>;
|
|
usb3-lpm-capable;
|
|
};
|