125 lines
5.8 KiB
Plaintext
125 lines
5.8 KiB
Plaintext
synopsys DWC3 CORE
|
|
|
|
DWC3- USB3 CONTROLLER. Complies to the generic USB binding properties
|
|
as described in 'usb/generic.txt'
|
|
|
|
Required properties:
|
|
- compatible: must be "snps,dwc3"
|
|
- reg : Address and length of the register set for the device
|
|
- interrupts: Interrupts used by the dwc3 controller.
|
|
- clock-names: should contain "ref", "bus_early", "suspend"
|
|
- clocks: list of phandle and clock specifier pairs corresponding to
|
|
entries in the clock-names property.
|
|
|
|
Exception for clocks:
|
|
clocks are optional if the parent node (i.e. glue-layer) is compatible to
|
|
one of the following:
|
|
"amlogic,meson-axg-dwc3"
|
|
"amlogic,meson-gxl-dwc3"
|
|
"cavium,octeon-7130-usb-uctl"
|
|
"qcom,dwc3"
|
|
"samsung,exynos5250-dwusb3"
|
|
"samsung,exynos5433-dwusb3"
|
|
"samsung,exynos7-dwusb3"
|
|
"sprd,sc9860-dwc3"
|
|
"st,stih407-dwc3"
|
|
"ti,am437x-dwc3"
|
|
"ti,dwc3"
|
|
"ti,keystone-dwc3"
|
|
"rockchip,rk3399-dwc3"
|
|
"xlnx,zynqmp-dwc3"
|
|
|
|
Optional properties:
|
|
- usb-phy : array of phandle for the PHY device. The first element
|
|
in the array is expected to be a handle to the USB2/HS PHY and
|
|
the second element is expected to be a handle to the USB3/SS PHY
|
|
- phys: from the *Generic PHY* bindings
|
|
- phy-names: from the *Generic PHY* bindings; supported names are "usb2-phy"
|
|
or "usb3-phy".
|
|
- resets: a single pair of phandle and reset specifier
|
|
- snps,usb2-lpm-disable: indicate if we don't want to enable USB2 HW LPM
|
|
- snps,usb3_lpm_capable: determines if platform is USB3 LPM capable
|
|
- snps,dis-start-transfer-quirk: when set, disable isoc START TRANSFER command
|
|
failure SW work-around for DWC_usb31 version 1.70a-ea06
|
|
and prior.
|
|
- snps,disable_scramble_quirk: true when SW should disable data scrambling.
|
|
Only really useful for FPGA builds.
|
|
- snps,has-lpm-erratum: true when DWC3 was configured with LPM Erratum enabled
|
|
- snps,lpm-nyet-threshold: LPM NYET threshold
|
|
- snps,u2exit_lfps_quirk: set if we want to enable u2exit lfps quirk
|
|
- snps,u2ss_inp3_quirk: set if we enable P3 OK for U2/SS Inactive quirk
|
|
- snps,req_p1p2p3_quirk: when set, the core will always request for
|
|
P1/P2/P3 transition sequence.
|
|
- snps,del_p1p2p3_quirk: when set core will delay P1/P2/P3 until a certain
|
|
amount of 8B10B errors occur.
|
|
- snps,del_phy_power_chg_quirk: when set core will delay PHY power change
|
|
from P0 to P1/P2/P3.
|
|
- snps,lfps_filter_quirk: when set core will filter LFPS reception.
|
|
- snps,rx_detect_poll_quirk: when set core will disable a 400us delay to start
|
|
Polling LFPS after RX.Detect.
|
|
- snps,tx_de_emphasis_quirk: when set core will set Tx de-emphasis value.
|
|
- snps,tx_de_emphasis: the value driven to the PHY is controlled by the
|
|
LTSSM during USB3 Compliance mode.
|
|
- snps,dis_u3_susphy_quirk: when set core will disable USB3 suspend phy.
|
|
- snps,dis_u2_susphy_quirk: when set core will disable USB2 suspend phy.
|
|
- snps,dis_enblslpm_quirk: when set clears the enblslpm in GUSB2PHYCFG,
|
|
disabling the suspend signal to the PHY.
|
|
- snps,dis-u1-entry-quirk: set if link entering into U1 needs to be disabled.
|
|
- snps,dis-u2-entry-quirk: set if link entering into U2 needs to be disabled.
|
|
- snps,dis_rxdet_inp3_quirk: when set core will disable receiver detection
|
|
in PHY P3 power state.
|
|
- snps,dis-u2-freeclk-exists-quirk: when set, clear the u2_freeclk_exists
|
|
in GUSB2PHYCFG, specify that USB2 PHY doesn't provide
|
|
a free-running PHY clock.
|
|
- snps,dis-del-phy-power-chg-quirk: when set core will change PHY power
|
|
from P0 to P1/P2/P3 without delay.
|
|
- snps,dis-tx-ipgap-linecheck-quirk: when set, disable u2mac linestate check
|
|
during HS transmit.
|
|
- snps,dis_metastability_quirk: when set, disable metastability workaround.
|
|
CAUTION: use only if you are absolutely sure of it.
|
|
- snps,is-utmi-l1-suspend: true when DWC3 asserts output signal
|
|
utmi_l1_suspend_n, false when asserts utmi_sleep_n
|
|
- snps,hird-threshold: HIRD threshold
|
|
- snps,hsphy_interface: High-Speed PHY interface selection between "utmi" for
|
|
UTMI+ and "ulpi" for ULPI when the DWC_USB3_HSPHY_INTERFACE has value 3.
|
|
- snps,quirk-frame-length-adjustment: Value for GFLADJ_30MHZ field of GFLADJ
|
|
register for post-silicon frame length adjustment when the
|
|
fladj_30mhz_sdbnd signal is invalid or incorrect.
|
|
- snps,rx-thr-num-pkt-prd: periodic ESS RX packet threshold count - host mode
|
|
only. Set this and rx-max-burst-prd to a valid,
|
|
non-zero value 1-16 (DWC_usb31 programming guide
|
|
section 1.2.4) to enable periodic ESS RX threshold.
|
|
- snps,rx-max-burst-prd: max periodic ESS RX burst size - host mode only. Set
|
|
this and rx-thr-num-pkt-prd to a valid, non-zero value
|
|
1-16 (DWC_usb31 programming guide section 1.2.4) to
|
|
enable periodic ESS RX threshold.
|
|
- snps,tx-thr-num-pkt-prd: periodic ESS TX packet threshold count - host mode
|
|
only. Set this and tx-max-burst-prd to a valid,
|
|
non-zero value 1-16 (DWC_usb31 programming guide
|
|
section 1.2.3) to enable periodic ESS TX threshold.
|
|
- snps,tx-max-burst-prd: max periodic ESS TX burst size - host mode only. Set
|
|
this and tx-thr-num-pkt-prd to a valid, non-zero value
|
|
1-16 (DWC_usb31 programming guide section 1.2.3) to
|
|
enable periodic ESS TX threshold.
|
|
|
|
- <DEPRECATED> tx-fifo-resize: determines if the FIFO *has* to be reallocated.
|
|
- snps,incr-burst-type-adjustment: Value for INCR burst type of GSBUSCFG0
|
|
register, undefined length INCR burst type enable and INCRx type.
|
|
When just one value, which means INCRX burst mode enabled. When
|
|
more than one value, which means undefined length INCR burst type
|
|
enabled. The values can be 1, 4, 8, 16, 32, 64, 128 and 256.
|
|
|
|
- in addition all properties from usb-xhci.txt from the current directory are
|
|
supported as well
|
|
|
|
|
|
This is usually a subnode to DWC3 glue to which it is connected.
|
|
|
|
dwc3@4a030000 {
|
|
compatible = "snps,dwc3";
|
|
reg = <0x4a030000 0xcfff>;
|
|
interrupts = <0 92 4>
|
|
usb-phy = <&usb2_phy>, <&usb3,phy>;
|
|
snps,incr-burst-type-adjustment = <1>, <4>, <8>, <16>;
|
|
};
|