201 lines
7.0 KiB
YAML
201 lines
7.0 KiB
YAML
# SPDX-License-Identifier: GPL-2.0
|
|
%YAML 1.2
|
|
---
|
|
$id: http://devicetree.org/schemas/regulator/regulator.yaml#
|
|
$schema: http://devicetree.org/meta-schemas/core.yaml#
|
|
|
|
title: Voltage/Current Regulators
|
|
|
|
maintainers:
|
|
- Liam Girdwood <lgirdwood@gmail.com>
|
|
- Mark Brown <broonie@kernel.org>
|
|
|
|
properties:
|
|
regulator-name:
|
|
description: A string used as a descriptive name for regulator outputs
|
|
$ref: "/schemas/types.yaml#/definitions/string"
|
|
|
|
regulator-min-microvolt:
|
|
description: smallest voltage consumers may set
|
|
|
|
regulator-max-microvolt:
|
|
description: largest voltage consumers may set
|
|
|
|
regulator-microvolt-offset:
|
|
description: Offset applied to voltages to compensate for voltage drops
|
|
|
|
regulator-min-microamp:
|
|
description: smallest current consumers may set
|
|
|
|
regulator-max-microamp:
|
|
description: largest current consumers may set
|
|
|
|
regulator-input-current-limit-microamp:
|
|
description: maximum input current regulator allows
|
|
|
|
regulator-always-on:
|
|
description: boolean, regulator should never be disabled
|
|
type: boolean
|
|
|
|
regulator-boot-on:
|
|
description: bootloader/firmware enabled regulator
|
|
type: boolean
|
|
|
|
regulator-allow-bypass:
|
|
description: allow the regulator to go into bypass mode
|
|
type: boolean
|
|
|
|
regulator-allow-set-load:
|
|
description: allow the regulator performance level to be configured
|
|
type: boolean
|
|
|
|
regulator-ramp-delay:
|
|
description: ramp delay for regulator(in uV/us) For hardware which supports
|
|
disabling ramp rate, it should be explicitly initialised to zero (regulator-ramp-delay
|
|
= <0>) for disabling ramp delay.
|
|
$ref: "/schemas/types.yaml#/definitions/uint32"
|
|
|
|
regulator-enable-ramp-delay:
|
|
description: The time taken, in microseconds, for the supply rail to
|
|
reach the target voltage, plus/minus whatever tolerance the board
|
|
design requires. This property describes the total system ramp time
|
|
required due to the combination of internal ramping of the regulator
|
|
itself, and board design issues such as trace capacitance and load
|
|
on the supply.
|
|
$ref: "/schemas/types.yaml#/definitions/uint32"
|
|
|
|
regulator-settling-time-us:
|
|
description: Settling time, in microseconds, for voltage change if regulator
|
|
have the constant time for any level voltage change. This is useful
|
|
when regulator have exponential voltage change.
|
|
|
|
regulator-settling-time-up-us:
|
|
description: Settling time, in microseconds, for voltage increase if
|
|
the regulator needs a constant time to settle after voltage increases
|
|
of any level. This is useful for regulators with exponential voltage
|
|
changes.
|
|
|
|
regulator-settling-time-down-us:
|
|
description: Settling time, in microseconds, for voltage decrease if
|
|
the regulator needs a constant time to settle after voltage decreases
|
|
of any level. This is useful for regulators with exponential voltage
|
|
changes.
|
|
|
|
regulator-soft-start:
|
|
description: Enable soft start so that voltage ramps slowly
|
|
type: boolean
|
|
|
|
regulator-initial-mode:
|
|
description: initial operating mode. The set of possible operating modes
|
|
depends on the capabilities of every hardware so each device binding
|
|
documentation explains which values the regulator supports.
|
|
$ref: "/schemas/types.yaml#/definitions/uint32"
|
|
|
|
regulator-allowed-modes:
|
|
description: list of operating modes that software is allowed to configure
|
|
for the regulator at run-time. Elements may be specified in any order.
|
|
The set of possible operating modes depends on the capabilities of
|
|
every hardware so each device binding document explains which values
|
|
the regulator supports.
|
|
$ref: "/schemas/types.yaml#/definitions/uint32-array"
|
|
|
|
regulator-system-load:
|
|
description: Load in uA present on regulator that is not captured by
|
|
any consumer request.
|
|
$ref: "/schemas/types.yaml#/definitions/uint32"
|
|
|
|
regulator-pull-down:
|
|
description: Enable pull down resistor when the regulator is disabled.
|
|
type: boolean
|
|
|
|
regulator-over-current-protection:
|
|
description: Enable over current protection.
|
|
type: boolean
|
|
|
|
regulator-active-discharge:
|
|
description: |
|
|
tristate, enable/disable active discharge of regulators. The values are:
|
|
0: Disable active discharge.
|
|
1: Enable active discharge.
|
|
Absence of this property will leave configuration to default.
|
|
allOf:
|
|
- $ref: "/schemas/types.yaml#/definitions/uint32"
|
|
- enum: [ 0, 1 ]
|
|
|
|
regulator-coupled-with:
|
|
description: Regulators with which the regulator is coupled. The linkage
|
|
is 2-way - all coupled regulators should be linked with each other.
|
|
A regulator should not be coupled with its supplier.
|
|
$ref: "/schemas/types.yaml#/definitions/phandle-array"
|
|
|
|
regulator-coupled-max-spread:
|
|
description: Array of maximum spread between voltages of coupled regulators
|
|
in microvolts, each value in the array relates to the corresponding
|
|
couple specified by the regulator-coupled-with property.
|
|
$ref: "/schemas/types.yaml#/definitions/uint32"
|
|
|
|
regulator-max-step-microvolt:
|
|
description: Maximum difference between current and target voltages
|
|
that can be changed safely in a single step.
|
|
|
|
patternProperties:
|
|
".*-supply$":
|
|
description: Input supply phandle(s) for this node
|
|
|
|
regulator-state-(standby|mem|disk):
|
|
type: object
|
|
description:
|
|
sub-nodes for regulator state in Standby, Suspend-to-RAM, and
|
|
Suspend-to-DISK modes. Equivalent with standby, mem, and disk Linux
|
|
sleep states.
|
|
|
|
properties:
|
|
regulator-on-in-suspend:
|
|
description: regulator should be on in suspend state.
|
|
type: boolean
|
|
|
|
regulator-off-in-suspend:
|
|
description: regulator should be off in suspend state.
|
|
type: boolean
|
|
|
|
regulator-suspend-min-microvolt:
|
|
description: minimum voltage may be set in suspend state.
|
|
|
|
regulator-suspend-max-microvolt:
|
|
description: maximum voltage may be set in suspend state.
|
|
|
|
regulator-suspend-microvolt:
|
|
description: the default voltage which regulator would be set in
|
|
suspend. This property is now deprecated, instead setting voltage
|
|
for suspend mode via the API which regulator driver provides is
|
|
recommended.
|
|
|
|
regulator-changeable-in-suspend:
|
|
description: whether the default voltage and the regulator on/off
|
|
in suspend can be changed in runtime.
|
|
type: boolean
|
|
|
|
regulator-mode:
|
|
description: operating mode in the given suspend state. The set
|
|
of possible operating modes depends on the capabilities of every
|
|
hardware so the valid modes are documented on each regulator device
|
|
tree binding document.
|
|
$ref: "/schemas/types.yaml#/definitions/uint32"
|
|
|
|
additionalProperties: false
|
|
|
|
examples:
|
|
- |
|
|
xyzreg: regulator@0 {
|
|
regulator-min-microvolt = <1000000>;
|
|
regulator-max-microvolt = <2500000>;
|
|
regulator-always-on;
|
|
vin-supply = <&vin>;
|
|
|
|
regulator-state-mem {
|
|
regulator-on-in-suspend;
|
|
};
|
|
};
|
|
|
|
...
|