69 lines
2.6 KiB
Plaintext
69 lines
2.6 KiB
Plaintext
CPSW Port's Interface Mode Selection PHY Tree Bindings
|
|
-----------------------------------------------
|
|
|
|
TI am335x/am437x/dra7(am5)/dm814x CPSW3G Ethernet Subsystem supports
|
|
two 10/100/1000 Ethernet ports with selectable G/MII, RMII, and RGMII interfaces.
|
|
The interface mode is selected by configuring the MII mode selection register(s)
|
|
(GMII_SEL) in the System Control Module chapter (SCM). GMII_SEL register(s) and
|
|
bit fields placement in SCM are different between SoCs while fields meaning
|
|
is the same.
|
|
+--------------+
|
|
+-------------------------------+ |SCM |
|
|
| CPSW | | +---------+ |
|
|
| +--------------------------------+gmii_sel | |
|
|
| | | | +---------+ |
|
|
| +----v---+ +--------+ | +--------------+
|
|
| |Port 1..<--+-->GMII/MII<------->
|
|
| | | | | | |
|
|
| +--------+ | +--------+ |
|
|
| | |
|
|
| | +--------+ |
|
|
| | | RMII <------->
|
|
| +--> | |
|
|
| | +--------+ |
|
|
| | |
|
|
| | +--------+ |
|
|
| | | RGMII <------->
|
|
| +--> | |
|
|
| +--------+ |
|
|
+-------------------------------+
|
|
|
|
CPSW Port's Interface Mode Selection PHY describes MII interface mode between
|
|
CPSW Port and Ethernet PHY which depends on Eth PHY and board configuration.
|
|
|
|
CPSW Port's Interface Mode Selection PHY device should defined as child device
|
|
of SCM node (scm_conf) and can be attached to each CPSW port node using standard
|
|
PHY bindings (See phy/phy-bindings.txt).
|
|
|
|
Required properties:
|
|
- compatible : Should be "ti,am3352-phy-gmii-sel" for am335x platform
|
|
"ti,dra7xx-phy-gmii-sel" for dra7xx/am57xx platform
|
|
"ti,am43xx-phy-gmii-sel" for am43xx platform
|
|
"ti,dm814-phy-gmii-sel" for dm814x platform
|
|
- reg : Address and length of the register set for the device
|
|
- #phy-cells : must be 2.
|
|
cell 1 - CPSW port number (starting from 1)
|
|
cell 2 - RMII refclk mode
|
|
|
|
Examples:
|
|
phy_gmii_sel: phy-gmii-sel {
|
|
compatible = "ti,am3352-phy-gmii-sel";
|
|
reg = <0x650 0x4>;
|
|
#phy-cells = <2>;
|
|
};
|
|
|
|
mac: ethernet@4a100000 {
|
|
compatible = "ti,am335x-cpsw","ti,cpsw";
|
|
...
|
|
|
|
cpsw_emac0: slave@4a100200 {
|
|
...
|
|
phys = <&phy_gmii_sel 1 1>;
|
|
};
|
|
|
|
cpsw_emac1: slave@4a100300 {
|
|
...
|
|
phys = <&phy_gmii_sel 2 1>;
|
|
};
|
|
};
|