68 lines
2.6 KiB
Plaintext
68 lines
2.6 KiB
Plaintext
* Spreadtrum SDHCI controller (sdhci-sprd)
|
|
|
|
The Secure Digital (SD) Host controller on Spreadtrum SoCs provides an interface
|
|
for MMC, SD and SDIO types of cards.
|
|
|
|
This file documents differences between the core properties in mmc.txt
|
|
and the properties used by the sdhci-sprd driver.
|
|
|
|
Required properties:
|
|
- compatible: Should contain "sprd,sdhci-r11".
|
|
- reg: physical base address of the controller and length.
|
|
- interrupts: Interrupts used by the SDHCI controller.
|
|
- clocks: Should contain phandle for the clock feeding the SDHCI controller
|
|
- clock-names: Should contain the following:
|
|
"sdio" - SDIO source clock (required)
|
|
"enable" - gate clock which used for enabling/disabling the device (required)
|
|
"2x_enable" - gate clock controlling the device for some special platforms (optional)
|
|
|
|
Optional properties:
|
|
- assigned-clocks: the same with "sdio" clock
|
|
- assigned-clock-parents: the default parent of "sdio" clock
|
|
- pinctrl-names: should be "default", "state_uhs"
|
|
- pinctrl-0: should contain default/high speed pin control
|
|
- pinctrl-1: should contain uhs mode pin control
|
|
|
|
PHY DLL delays are used to delay the data valid window, and align the window
|
|
to sampling clock. PHY DLL delays can be configured by following properties,
|
|
and each property contains 4 cells which are used to configure the clock data
|
|
write line delay value, clock read command line delay value, clock read data
|
|
positive edge delay value and clock read data negative edge delay value.
|
|
Each cell's delay value unit is cycle of the PHY clock.
|
|
|
|
- sprd,phy-delay-legacy: Delay value for legacy timing.
|
|
- sprd,phy-delay-sd-highspeed: Delay value for SD high-speed timing.
|
|
- sprd,phy-delay-sd-uhs-sdr50: Delay value for SD UHS SDR50 timing.
|
|
- sprd,phy-delay-sd-uhs-sdr104: Delay value for SD UHS SDR50 timing.
|
|
- sprd,phy-delay-mmc-highspeed: Delay value for MMC high-speed timing.
|
|
- sprd,phy-delay-mmc-ddr52: Delay value for MMC DDR52 timing.
|
|
- sprd,phy-delay-mmc-hs200: Delay value for MMC HS200 timing.
|
|
- sprd,phy-delay-mmc-hs400: Delay value for MMC HS400 timing.
|
|
- sprd,phy-delay-mmc-hs400es: Delay value for MMC HS400 enhanced strobe timing.
|
|
|
|
Examples:
|
|
|
|
sdio0: sdio@20600000 {
|
|
compatible = "sprd,sdhci-r11";
|
|
reg = <0 0x20600000 0 0x1000>;
|
|
interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
|
|
|
|
clock-names = "sdio", "enable";
|
|
clocks = <&ap_clk CLK_EMMC_2X>,
|
|
<&apahb_gate CLK_EMMC_EB>;
|
|
assigned-clocks = <&ap_clk CLK_EMMC_2X>;
|
|
assigned-clock-parents = <&rpll CLK_RPLL_390M>;
|
|
|
|
pinctrl-names = "default", "state_uhs";
|
|
pinctrl-0 = <&sd0_pins_default>;
|
|
pinctrl-1 = <&sd0_pins_uhs>;
|
|
|
|
sprd,phy-delay-sd-uhs-sdr104 = <0x3f 0x7f 0x2e 0x2e>;
|
|
bus-width = <8>;
|
|
non-removable;
|
|
no-sdio;
|
|
no-sd;
|
|
cap-mmc-hw-reset;
|
|
status = "okay";
|
|
};
|