269 lines
8.8 KiB
Plaintext
269 lines
8.8 KiB
Plaintext
The `parport' code provides parallel-port support under Linux. This
|
|
includes the ability to share one port between multiple device
|
|
drivers.
|
|
|
|
You can pass parameters to the parport code to override its automatic
|
|
detection of your hardware. This is particularly useful if you want
|
|
to use IRQs, since in general these can't be autoprobed successfully.
|
|
By default IRQs are not used even if they _can_ be probed. This is
|
|
because there are a lot of people using the same IRQ for their
|
|
parallel port and a sound card or network card.
|
|
|
|
The parport code is split into two parts: generic (which deals with
|
|
port-sharing) and architecture-dependent (which deals with actually
|
|
using the port).
|
|
|
|
|
|
Parport as modules
|
|
==================
|
|
|
|
If you load the parport code as a module, say
|
|
|
|
# insmod parport
|
|
|
|
to load the generic parport code. You then must load the
|
|
architecture-dependent code with (for example):
|
|
|
|
# insmod parport_pc io=0x3bc,0x378,0x278 irq=none,7,auto
|
|
|
|
to tell the parport code that you want three PC-style ports, one at
|
|
0x3bc with no IRQ, one at 0x378 using IRQ 7, and one at 0x278 with an
|
|
auto-detected IRQ. Currently, PC-style (parport_pc), Sun `bpp',
|
|
Amiga, Atari, and MFC3 hardware is supported.
|
|
|
|
PCI parallel I/O card support comes from parport_pc. Base I/O
|
|
addresses should not be specified for supported PCI cards since they
|
|
are automatically detected.
|
|
|
|
|
|
KMod
|
|
----
|
|
|
|
If you use kmod, you will find it useful to edit /etc/modprobe.conf.
|
|
Here is an example of the lines that need to be added:
|
|
|
|
alias parport_lowlevel parport_pc
|
|
options parport_pc io=0x378,0x278 irq=7,auto
|
|
|
|
KMod will then automatically load parport_pc (with the options
|
|
"io=0x378,0x278 irq=7,auto") whenever a parallel port device driver
|
|
(such as lp) is loaded.
|
|
|
|
Note that these are example lines only! You shouldn't in general need
|
|
to specify any options to parport_pc in order to be able to use a
|
|
parallel port.
|
|
|
|
|
|
Parport probe [optional]
|
|
-------------
|
|
|
|
In 2.2 kernels there was a module called parport_probe, which was used
|
|
for collecting IEEE 1284 device ID information. This has now been
|
|
enhanced and now lives with the IEEE 1284 support. When a parallel
|
|
port is detected, the devices that are connected to it are analysed,
|
|
and information is logged like this:
|
|
|
|
parport0: Printer, BJC-210 (Canon)
|
|
|
|
The probe information is available from files in /proc/sys/dev/parport/.
|
|
|
|
|
|
Parport linked into the kernel statically
|
|
=========================================
|
|
|
|
If you compile the parport code into the kernel, then you can use
|
|
kernel boot parameters to get the same effect. Add something like the
|
|
following to your LILO command line:
|
|
|
|
parport=0x3bc parport=0x378,7 parport=0x278,auto,nofifo
|
|
|
|
You can have many `parport=...' statements, one for each port you want
|
|
to add. Adding `parport=0' to the kernel command-line will disable
|
|
parport support entirely. Adding `parport=auto' to the kernel
|
|
command-line will make parport use any IRQ lines or DMA channels that
|
|
it auto-detects.
|
|
|
|
|
|
Files in /proc
|
|
==============
|
|
|
|
If you have configured the /proc filesystem into your kernel, you will
|
|
see a new directory entry: /proc/sys/dev/parport. In there will be a
|
|
directory entry for each parallel port for which parport is
|
|
configured. In each of those directories are a collection of files
|
|
describing that parallel port.
|
|
|
|
The /proc/sys/dev/parport directory tree looks like:
|
|
|
|
parport
|
|
|-- default
|
|
| |-- spintime
|
|
| `-- timeslice
|
|
|-- parport0
|
|
| |-- autoprobe
|
|
| |-- autoprobe0
|
|
| |-- autoprobe1
|
|
| |-- autoprobe2
|
|
| |-- autoprobe3
|
|
| |-- devices
|
|
| | |-- active
|
|
| | `-- lp
|
|
| | `-- timeslice
|
|
| |-- base-addr
|
|
| |-- irq
|
|
| |-- dma
|
|
| |-- modes
|
|
| `-- spintime
|
|
`-- parport1
|
|
|-- autoprobe
|
|
|-- autoprobe0
|
|
|-- autoprobe1
|
|
|-- autoprobe2
|
|
|-- autoprobe3
|
|
|-- devices
|
|
| |-- active
|
|
| `-- ppa
|
|
| `-- timeslice
|
|
|-- base-addr
|
|
|-- irq
|
|
|-- dma
|
|
|-- modes
|
|
`-- spintime
|
|
|
|
|
|
File: Contents:
|
|
|
|
devices/active A list of the device drivers using that port. A "+"
|
|
will appear by the name of the device currently using
|
|
the port (it might not appear against any). The
|
|
string "none" means that there are no device drivers
|
|
using that port.
|
|
|
|
base-addr Parallel port's base address, or addresses if the port
|
|
has more than one in which case they are separated
|
|
with tabs. These values might not have any sensible
|
|
meaning for some ports.
|
|
|
|
irq Parallel port's IRQ, or -1 if none is being used.
|
|
|
|
dma Parallel port's DMA channel, or -1 if none is being
|
|
used.
|
|
|
|
modes Parallel port's hardware modes, comma-separated,
|
|
meaning:
|
|
|
|
PCSPP PC-style SPP registers are available.
|
|
TRISTATE Port is bidirectional.
|
|
COMPAT Hardware acceleration for printers is
|
|
available and will be used.
|
|
EPP Hardware acceleration for EPP protocol
|
|
is available and will be used.
|
|
ECP Hardware acceleration for ECP protocol
|
|
is available and will be used.
|
|
DMA DMA is available and will be used.
|
|
|
|
Note that the current implementation will only take
|
|
advantage of COMPAT and ECP modes if it has an IRQ
|
|
line to use.
|
|
|
|
autoprobe Any IEEE-1284 device ID information that has been
|
|
acquired from the (non-IEEE 1284.3) device.
|
|
|
|
autoprobe[0-3] IEEE 1284 device ID information retrieved from
|
|
daisy-chain devices that conform to IEEE 1284.3.
|
|
|
|
spintime The number of microseconds to busy-loop while waiting
|
|
for the peripheral to respond. You might find that
|
|
adjusting this improves performance, depending on your
|
|
peripherals. This is a port-wide setting, i.e. it
|
|
applies to all devices on a particular port.
|
|
|
|
timeslice The number of milliseconds that a device driver is
|
|
allowed to keep a port claimed for. This is advisory,
|
|
and driver can ignore it if it must.
|
|
|
|
default/* The defaults for spintime and timeslice. When a new
|
|
port is registered, it picks up the default spintime.
|
|
When a new device is registered, it picks up the
|
|
default timeslice.
|
|
|
|
Device drivers
|
|
==============
|
|
|
|
Once the parport code is initialised, you can attach device drivers to
|
|
specific ports. Normally this happens automatically; if the lp driver
|
|
is loaded it will create one lp device for each port found. You can
|
|
override this, though, by using parameters either when you load the lp
|
|
driver:
|
|
|
|
# insmod lp parport=0,2
|
|
|
|
or on the LILO command line:
|
|
|
|
lp=parport0 lp=parport2
|
|
|
|
Both the above examples would inform lp that you want /dev/lp0 to be
|
|
the first parallel port, and /dev/lp1 to be the _third_ parallel port,
|
|
with no lp device associated with the second port (parport1). Note
|
|
that this is different to the way older kernels worked; there used to
|
|
be a static association between the I/O port address and the device
|
|
name, so /dev/lp0 was always the port at 0x3bc. This is no longer the
|
|
case - if you only have one port, it will default to being /dev/lp0,
|
|
regardless of base address.
|
|
|
|
Also:
|
|
|
|
* If you selected the IEEE 1284 support at compile time, you can say
|
|
`lp=auto' on the kernel command line, and lp will create devices
|
|
only for those ports that seem to have printers attached.
|
|
|
|
* If you give PLIP the `timid' parameter, either with `plip=timid' on
|
|
the command line, or with `insmod plip timid=1' when using modules,
|
|
it will avoid any ports that seem to be in use by other devices.
|
|
|
|
* IRQ autoprobing works only for a few port types at the moment.
|
|
|
|
Reporting printer problems with parport
|
|
=======================================
|
|
|
|
If you are having problems printing, please go through these steps to
|
|
try to narrow down where the problem area is.
|
|
|
|
When reporting problems with parport, really you need to give all of
|
|
the messages that parport_pc spits out when it initialises. There are
|
|
several code paths:
|
|
|
|
o polling
|
|
o interrupt-driven, protocol in software
|
|
o interrupt-driven, protocol in hardware using PIO
|
|
o interrupt-driven, protocol in hardware using DMA
|
|
|
|
The kernel messages that parport_pc logs give an indication of which
|
|
code path is being used. (They could be a lot better actually..)
|
|
|
|
For normal printer protocol, having IEEE 1284 modes enabled or not
|
|
should not make a difference.
|
|
|
|
To turn off the 'protocol in hardware' code paths, disable
|
|
CONFIG_PARPORT_PC_FIFO. Note that when they are enabled they are not
|
|
necessarily _used_; it depends on whether the hardware is available,
|
|
enabled by the BIOS, and detected by the driver.
|
|
|
|
So, to start with, disable CONFIG_PARPORT_PC_FIFO, and load parport_pc
|
|
with 'irq=none'. See if printing works then. It really should,
|
|
because this is the simplest code path.
|
|
|
|
If that works fine, try with 'io=0x378 irq=7' (adjust for your
|
|
hardware), to make it use interrupt-driven in-software protocol.
|
|
|
|
If _that_ works fine, then one of the hardware modes isn't working
|
|
right. Enable CONFIG_PARPORT_PC_FIFO (no, it isn't a module option,
|
|
and yes, it should be), set the port to ECP mode in the BIOS and note
|
|
the DMA channel, and try with:
|
|
|
|
io=0x378 irq=7 dma=none (for PIO)
|
|
io=0x378 irq=7 dma=3 (for DMA)
|
|
--
|
|
philb@gnu.org
|
|
tim@cyberelk.net
|