OpenCloudOS-Kernel/arch/arm/boot/dts/omap3-igep0020.dts

177 lines
4.2 KiB
Plaintext

/*
* Device Tree Source for IGEPv2 board
*
* Copyright (C) 2012 Javier Martinez Canillas <javier@collabora.co.uk>
* Copyright (C) 2012 Enric Balletbo i Serra <eballetbo@gmail.com>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
#include "omap3-igep.dtsi"
#include "omap-gpmc-smsc911x.dtsi"
/ {
model = "IGEPv2";
compatible = "isee,omap3-igep0020", "ti,omap3";
leds {
pinctrl-names = "default";
pinctrl-0 = <&leds_pins>;
compatible = "gpio-leds";
boot {
label = "omap3:green:boot";
gpios = <&gpio1 26 GPIO_ACTIVE_HIGH>;
default-state = "on";
};
user0 {
label = "omap3:red:user0";
gpios = <&gpio1 27 GPIO_ACTIVE_HIGH>;
default-state = "off";
};
user1 {
label = "omap3:red:user1";
gpios = <&gpio1 28 GPIO_ACTIVE_HIGH>;
default-state = "off";
};
user2 {
label = "omap3:green:user1";
gpios = <&twl_gpio 19 GPIO_ACTIVE_LOW>;
};
};
/* HS USB Port 1 Power */
hsusb1_power: hsusb1_power_reg {
compatible = "regulator-fixed";
regulator-name = "hsusb1_vbus";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
gpio = <&twl_gpio 18 GPIO_ACTIVE_LOW>; /* GPIO LEDA */
startup-delay-us = <70000>;
};
/* HS USB Host PHY on PORT 1 */
hsusb1_phy: hsusb1_phy {
compatible = "usb-nop-xceiv";
reset-gpios = <&gpio1 24 GPIO_ACTIVE_LOW>; /* gpio_24 */
vcc-supply = <&hsusb1_power>;
};
};
&omap3_pmx_core {
pinctrl-names = "default";
pinctrl-0 = <
&hsusbb1_pins
>;
hsusbb1_pins: pinmux_hsusbb1_pins {
pinctrl-single,pins = <
0x5aa (PIN_OUTPUT | MUX_MODE3) /* etk_ctl.hsusb1_clk */
0x5a8 (PIN_OUTPUT | MUX_MODE3) /* etk_clk.hsusb1_stp */
0x5bc (PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d8.hsusb1_dir */
0x5be (PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d9.hsusb1_nxt */
0x5ac (PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d0.hsusb1_data0 */
0x5ae (PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d1.hsusb1_data1 */
0x5b0 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d2.hsusb1_data2 */
0x5b2 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d3.hsusb1_data7 */
0x5b4 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d4.hsusb1_data4 */
0x5b6 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d5.hsusb1_data5 */
0x5b8 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d6.hsusb1_data6 */
0x5ba (PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d7.hsusb1_data3 */
>;
};
};
&leds_pins {
pinctrl-single,pins = <
0x5c4 (PIN_OUTPUT | MUX_MODE4) /* etk_d12.gpio_26 */
0x5c6 (PIN_OUTPUT | MUX_MODE4) /* etk_d13.gpio_27 */
0x5c8 (PIN_OUTPUT | MUX_MODE4) /* etk_d14.gpio_28 */
>;
};
&i2c3 {
clock-frequency = <100000>;
/*
* Display monitor features are burnt in the EEPROM
* as EDID data.
*/
eeprom@50 {
compatible = "ti,eeprom";
reg = <0x50>;
};
};
&gpmc {
ranges = <0 0 0x00000000 0x20000000>,
<5 0 0x2c000000 0x01000000>;
nand@0,0 {
linux,mtd-name= "micron,mt29c4g96maz";
reg = <0 0 0>;
nand-bus-width = <16>;
ti,nand-ecc-opt = "bch8";
gpmc,sync-clk-ps = <0>;
gpmc,cs-on-ns = <0>;
gpmc,cs-rd-off-ns = <44>;
gpmc,cs-wr-off-ns = <44>;
gpmc,adv-on-ns = <6>;
gpmc,adv-rd-off-ns = <34>;
gpmc,adv-wr-off-ns = <44>;
gpmc,we-off-ns = <40>;
gpmc,oe-off-ns = <54>;
gpmc,access-ns = <64>;
gpmc,rd-cycle-ns = <82>;
gpmc,wr-cycle-ns = <82>;
gpmc,wr-access-ns = <40>;
gpmc,wr-data-mux-bus-ns = <0>;
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
label = "SPL";
reg = <0 0x100000>;
};
partition@80000 {
label = "U-Boot";
reg = <0x100000 0x180000>;
};
partition@1c0000 {
label = "Environment";
reg = <0x280000 0x100000>;
};
partition@280000 {
label = "Kernel";
reg = <0x380000 0x300000>;
};
partition@780000 {
label = "Filesystem";
reg = <0x680000 0x1f980000>;
};
};
ethernet@gpmc {
pinctrl-names = "default";
pinctrl-0 = <&smsc911x_pins>;
reg = <5 0 0xff>;
interrupt-parent = <&gpio6>;
interrupts = <16 IRQ_TYPE_LEVEL_LOW>;
};
};
&usbhshost {
port1-mode = "ehci-phy";
};
&usbhsehci {
phys = <&hsusb1_phy>;
};