OpenCloudOS-Kernel/arch/arm/boot/dts/omap3-beagle.dts

181 lines
3.8 KiB
Plaintext

/*
* Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
/dts-v1/;
#include "omap34xx.dtsi"
/ {
model = "TI OMAP3 BeagleBoard";
compatible = "ti,omap3-beagle", "ti,omap3";
cpus {
cpu@0 {
cpu0-supply = <&vcc>;
};
};
memory {
device_type = "memory";
reg = <0x80000000 0x10000000>; /* 256 MB */
};
leds {
compatible = "gpio-leds";
pmu_stat {
label = "beagleboard::pmu_stat";
gpios = <&twl_gpio 19 GPIO_ACTIVE_HIGH>; /* LEDB */
};
heartbeat {
label = "beagleboard::usr0";
gpios = <&gpio5 22 GPIO_ACTIVE_HIGH>; /* 150 -> D6 LED */
linux,default-trigger = "heartbeat";
};
mmc {
label = "beagleboard::usr1";
gpios = <&gpio5 21 GPIO_ACTIVE_HIGH>; /* 149 -> D7 LED */
linux,default-trigger = "mmc0";
};
};
/* HS USB Port 2 Power */
hsusb2_power: hsusb2_power_reg {
compatible = "regulator-fixed";
regulator-name = "hsusb2_vbus";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
gpio = <&twl_gpio 18 0>; /* GPIO LEDA */
startup-delay-us = <70000>;
};
/* HS USB Host PHY on PORT 2 */
hsusb2_phy: hsusb2_phy {
compatible = "usb-nop-xceiv";
reset-gpios = <&gpio5 19 GPIO_ACTIVE_LOW>; /* gpio_147 */
vcc-supply = <&hsusb2_power>;
};
gpio_keys {
compatible = "gpio-keys";
user {
label = "user";
gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>;
linux,code = <0x114>;
gpio-key,wakeup;
};
};
};
&omap3_pmx_wkup {
gpio1_pins: pinmux_gpio1_pins {
pinctrl-single,pins = <
0x14 (PIN_INPUT | PIN_OFF_WAKEUPENABLE | MUX_MODE4) /* sys_boot5.gpio_7 */
>;
};
};
&omap3_pmx_core {
pinctrl-names = "default";
pinctrl-0 = <
&hsusbb2_pins
>;
hsusbb2_pins: pinmux_hsusbb2_pins {
pinctrl-single,pins = <
0x5c0 (PIN_OUTPUT | MUX_MODE3) /* etk_d10.hsusb2_clk */
0x5c2 (PIN_OUTPUT | MUX_MODE3) /* etk_d11.hsusb2_stp */
0x5c4 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d12.hsusb2_dir */
0x5c6 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d13.hsusb2_nxt */
0x5c8 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d14.hsusb2_data0 */
0x5cA (PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d15.hsusb2_data1 */
0x1a4 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi1_cs3.hsusb2_data2 */
0x1a6 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_clk.hsusb2_data7 */
0x1a8 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_simo.hsusb2_data4 */
0x1aa (PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_somi.hsusb2_data5 */
0x1ac (PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_cs0.hsusb2_data6 */
0x1ae (PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_cs1.hsusb2_data3 */
>;
};
uart3_pins: pinmux_uart3_pins {
pinctrl-single,pins = <
0x16e (PIN_INPUT | PIN_OFF_WAKEUPENABLE | MUX_MODE0) /* uart3_rx_irrx.uart3_rx_irrx */
0x170 (PIN_OUTPUT | MUX_MODE0) /* uart3_tx_irtx.uart3_tx_irtx */
>;
};
};
&i2c1 {
clock-frequency = <2600000>;
twl: twl@48 {
reg = <0x48>;
interrupts = <7>; /* SYS_NIRQ cascaded to intc */
interrupt-parent = <&intc>;
};
};
#include "twl4030.dtsi"
#include "twl4030_omap3.dtsi"
&mmc1 {
vmmc-supply = <&vmmc1>;
vmmc_aux-supply = <&vsim>;
bus-width = <8>;
};
&mmc2 {
status = "disabled";
};
&mmc3 {
status = "disabled";
};
&usbhshost {
port2-mode = "ehci-phy";
};
&usbhsehci {
phys = <0 &hsusb2_phy>;
};
&twl_gpio {
ti,use-leds;
/* pullups: BIT(1) */
ti,pullups = <0x000002>;
/*
* pulldowns:
* BIT(2), BIT(6), BIT(7), BIT(8), BIT(13)
* BIT(15), BIT(16), BIT(17)
*/
ti,pulldowns = <0x03a1c4>;
};
&uart3 {
pinctrl-names = "default";
pinctrl-0 = <&uart3_pins>;
};
&gpio1 {
pinctrl-names = "default";
pinctrl-0 = <&gpio1_pins>;
};
&usb_otg_hs {
interface-type = <0>;
usb-phy = <&usb2_phy>;
phys = <&usb2_phy>;
phy-names = "usb2-phy";
mode = <3>;
power = <50>;
};