79 lines
2.6 KiB
Plaintext
79 lines
2.6 KiB
Plaintext
OMAP GLUE AND OTHER OMAP SPECIFIC COMPONENTS
|
|
|
|
OMAP MUSB GLUE
|
|
- compatible : Should be "ti,omap4-musb" or "ti,omap3-musb"
|
|
- ti,hwmods : must be "usb_otg_hs"
|
|
- multipoint : Should be "1" indicating the musb controller supports
|
|
multipoint. This is a MUSB configuration-specific setting.
|
|
- num-eps : Specifies the number of endpoints. This is also a
|
|
MUSB configuration-specific setting. Should be set to "16"
|
|
- ram-bits : Specifies the ram address size. Should be set to "12"
|
|
- interface-type : This is a board specific setting to describe the type of
|
|
interface between the controller and the phy. It should be "0" or "1"
|
|
specifying ULPI and UTMI respectively.
|
|
- mode : Should be "3" to represent OTG. "1" signifies HOST and "2"
|
|
represents PERIPHERAL.
|
|
- power : Should be "50". This signifies the controller can supply up to
|
|
100mA when operating in host mode.
|
|
- usb-phy : the phandle for the PHY device
|
|
- phys : the phandle for the PHY device (used by generic PHY framework)
|
|
- phy-names : the names of the PHY corresponding to the PHYs present in the
|
|
*phy* phandle.
|
|
|
|
Optional properties:
|
|
- ctrl-module : phandle of the control module this glue uses to write to
|
|
mailbox
|
|
|
|
SOC specific device node entry
|
|
usb_otg_hs: usb_otg_hs@4a0ab000 {
|
|
compatible = "ti,omap4-musb";
|
|
ti,hwmods = "usb_otg_hs";
|
|
multipoint = <1>;
|
|
num-eps = <16>;
|
|
ram-bits = <12>;
|
|
ctrl-module = <&omap_control_usb>;
|
|
phys = <&usb2_phy>;
|
|
phy-names = "usb2-phy";
|
|
};
|
|
|
|
Board specific device node entry
|
|
&usb_otg_hs {
|
|
interface-type = <1>;
|
|
mode = <3>;
|
|
power = <50>;
|
|
};
|
|
|
|
OMAP DWC3 GLUE
|
|
- compatible : Should be "ti,dwc3"
|
|
- ti,hwmods : Should be "usb_otg_ss"
|
|
- reg : Address and length of the register set for the device.
|
|
- interrupts : The irq number of this device that is used to interrupt the
|
|
MPU
|
|
- #address-cells, #size-cells : Must be present if the device has sub-nodes
|
|
- utmi-mode : controls the source of UTMI/PIPE status for VBUS and OTG ID.
|
|
It should be set to "1" for HW mode and "2" for SW mode.
|
|
- ranges: the child address space are mapped 1:1 onto the parent address space
|
|
|
|
Optional Properties:
|
|
- extcon : phandle for the extcon device omap dwc3 uses to detect
|
|
connect/disconnect events.
|
|
- vbus-supply : phandle to the regulator device tree node if needed.
|
|
|
|
Sub-nodes:
|
|
The dwc3 core should be added as subnode to omap dwc3 glue.
|
|
- dwc3 :
|
|
The binding details of dwc3 can be found in:
|
|
Documentation/devicetree/bindings/usb/dwc3.txt
|
|
|
|
omap_dwc3 {
|
|
compatible = "ti,dwc3";
|
|
ti,hwmods = "usb_otg_ss";
|
|
reg = <0x4a020000 0x1ff>;
|
|
interrupts = <0 93 4>;
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
utmi-mode = <2>;
|
|
ranges;
|
|
};
|
|
|