179 lines
3.2 KiB
Plaintext
179 lines
3.2 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0+
|
|
/*
|
|
* Copyright (C) 2015 Altera Corporation <www.altera.com>
|
|
*/
|
|
#include "socfpga_arria10.dtsi"
|
|
|
|
/ {
|
|
model = "Altera SOCFPGA Arria 10";
|
|
compatible = "altr,socfpga-arria10", "altr,socfpga";
|
|
|
|
aliases {
|
|
ethernet0 = &gmac0;
|
|
serial0 = &uart1;
|
|
};
|
|
|
|
chosen {
|
|
bootargs = "earlyprintk";
|
|
stdout-path = "serial0:115200n8";
|
|
};
|
|
|
|
memory@0 {
|
|
name = "memory";
|
|
device_type = "memory";
|
|
reg = <0x0 0x40000000>; /* 1GB */
|
|
};
|
|
|
|
a10leds {
|
|
compatible = "gpio-leds";
|
|
|
|
a10sr_led0 {
|
|
label = "a10sr-led0";
|
|
gpios = <&a10sr_gpio 0 1>;
|
|
};
|
|
|
|
a10sr_led1 {
|
|
label = "a10sr-led1";
|
|
gpios = <&a10sr_gpio 1 1>;
|
|
};
|
|
|
|
a10sr_led2 {
|
|
label = "a10sr-led2";
|
|
gpios = <&a10sr_gpio 2 1>;
|
|
};
|
|
|
|
a10sr_led3 {
|
|
label = "a10sr-led3";
|
|
gpios = <&a10sr_gpio 3 1>;
|
|
};
|
|
};
|
|
|
|
ref_033v: 033-v-ref {
|
|
compatible = "regulator-fixed";
|
|
regulator-name = "0.33V";
|
|
regulator-min-microvolt = <330000>;
|
|
regulator-max-microvolt = <330000>;
|
|
};
|
|
|
|
soc {
|
|
clkmgr@ffd04000 {
|
|
clocks {
|
|
osc1 {
|
|
clock-frequency = <25000000>;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
&gmac0 {
|
|
phy-mode = "rgmii";
|
|
phy-addr = <0xffffffff>; /* probe for phy addr */
|
|
|
|
/*
|
|
* These skews assume the user's FPGA design is adding 600ps of delay
|
|
* for TX_CLK on Arria 10.
|
|
*
|
|
* All skews are offset since hardware skew values for the ksz9031
|
|
* range from a negative skew to a positive skew.
|
|
* See the micrel-ksz90x1.txt Documentation file for details.
|
|
*/
|
|
txd0-skew-ps = <0>; /* -420ps */
|
|
txd1-skew-ps = <0>; /* -420ps */
|
|
txd2-skew-ps = <0>; /* -420ps */
|
|
txd3-skew-ps = <0>; /* -420ps */
|
|
rxd0-skew-ps = <420>; /* 0ps */
|
|
rxd1-skew-ps = <420>; /* 0ps */
|
|
rxd2-skew-ps = <420>; /* 0ps */
|
|
rxd3-skew-ps = <420>; /* 0ps */
|
|
txen-skew-ps = <0>; /* -420ps */
|
|
txc-skew-ps = <1860>; /* 960ps */
|
|
rxdv-skew-ps = <420>; /* 0ps */
|
|
rxc-skew-ps = <1680>; /* 780ps */
|
|
max-frame-size = <3800>;
|
|
status = "okay";
|
|
};
|
|
|
|
&gpio1 {
|
|
status = "okay";
|
|
};
|
|
|
|
&spi1 {
|
|
status = "okay";
|
|
|
|
resource-manager@0 {
|
|
compatible = "altr,a10sr";
|
|
reg = <0>;
|
|
spi-max-frequency = <100000>;
|
|
/* low-level active IRQ at GPIO1_5 */
|
|
interrupt-parent = <&portb>;
|
|
interrupts = <5 IRQ_TYPE_LEVEL_LOW>;
|
|
interrupt-controller;
|
|
#interrupt-cells = <2>;
|
|
|
|
a10sr_gpio: gpio-controller {
|
|
compatible = "altr,a10sr-gpio";
|
|
gpio-controller;
|
|
#gpio-cells = <2>;
|
|
};
|
|
|
|
a10sr_rst: reset-controller {
|
|
compatible = "altr,a10sr-reset";
|
|
#reset-cells = <1>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&i2c1 {
|
|
status = "okay";
|
|
|
|
/*
|
|
* adjust the falling times to decrease the i2c frequency to 50Khz
|
|
* because the LCD module does not work at the standard 100Khz
|
|
*/
|
|
clock-frequency = <100000>;
|
|
i2c-sda-falling-time-ns = <6000>;
|
|
i2c-scl-falling-time-ns = <6000>;
|
|
|
|
adc@14 {
|
|
compatible = "lltc,ltc2497";
|
|
reg = <0x14>;
|
|
vref-supply = <&ref_033v>;
|
|
};
|
|
|
|
adc@16 {
|
|
compatible = "lltc,ltc2497";
|
|
reg = <0x16>;
|
|
vref-supply = <&ref_033v>;
|
|
};
|
|
|
|
eeprom@51 {
|
|
compatible = "atmel,24c32";
|
|
reg = <0x51>;
|
|
pagesize = <32>;
|
|
};
|
|
|
|
rtc@68 {
|
|
compatible = "dallas,ds1339";
|
|
reg = <0x68>;
|
|
};
|
|
|
|
ltc@5c {
|
|
compatible = "ltc2977";
|
|
reg = <0x5c>;
|
|
};
|
|
};
|
|
|
|
&uart1 {
|
|
status = "okay";
|
|
};
|
|
|
|
&usb0 {
|
|
status = "okay";
|
|
disable-over-current;
|
|
};
|
|
|
|
&watchdog1 {
|
|
status = "okay";
|
|
};
|