148 lines
6.0 KiB
ReStructuredText
148 lines
6.0 KiB
ReStructuredText
.. SPDX-License-Identifier: GPL-2.0
|
|
|
|
Writing camera sensor drivers
|
|
=============================
|
|
|
|
CSI-2
|
|
-----
|
|
|
|
Please see what is written on :ref:`MIPI_CSI_2`.
|
|
|
|
Handling clocks
|
|
---------------
|
|
|
|
Camera sensors have an internal clock tree including a PLL and a number of
|
|
divisors. The clock tree is generally configured by the driver based on a few
|
|
input parameters that are specific to the hardware:: the external clock frequency
|
|
and the link frequency. The two parameters generally are obtained from system
|
|
firmware. No other frequencies should be used in any circumstances.
|
|
|
|
The reason why the clock frequencies are so important is that the clock signals
|
|
come out of the SoC, and in many cases a specific frequency is designed to be
|
|
used in the system. Using another frequency may cause harmful effects
|
|
elsewhere. Therefore only the pre-determined frequencies are configurable by the
|
|
user.
|
|
|
|
Frame size
|
|
----------
|
|
|
|
There are two distinct ways to configure the frame size produced by camera
|
|
sensors.
|
|
|
|
Freely configurable camera sensor drivers
|
|
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
|
|
|
|
Freely configurable camera sensor drivers expose the device's internal
|
|
processing pipeline as one or more sub-devices with different cropping and
|
|
scaling configurations. The output size of the device is the result of a series
|
|
of cropping and scaling operations from the device's pixel array's size.
|
|
|
|
An example of such a driver is the smiapp driver (see drivers/media/i2c/smiapp).
|
|
|
|
Register list based drivers
|
|
~~~~~~~~~~~~~~~~~~~~~~~~~~~
|
|
|
|
Register list based drivers generally, instead of able to configure the device
|
|
they control based on user requests, are limited to a number of preset
|
|
configurations that combine a number of different parameters that on hardware
|
|
level are independent. How a driver picks such configuration is based on the
|
|
format set on a source pad at the end of the device's internal pipeline.
|
|
|
|
Most sensor drivers are implemented this way, see e.g.
|
|
drivers/media/i2c/imx319.c for an example.
|
|
|
|
Frame interval configuration
|
|
----------------------------
|
|
|
|
There are two different methods for obtaining possibilities for different frame
|
|
intervals as well as configuring the frame interval. Which one to implement
|
|
depends on the type of the device.
|
|
|
|
Raw camera sensors
|
|
~~~~~~~~~~~~~~~~~~
|
|
|
|
Instead of a high level parameter such as frame interval, the frame interval is
|
|
a result of the configuration of a number of camera sensor implementation
|
|
specific parameters. Luckily, these parameters tend to be the same for more or
|
|
less all modern raw camera sensors.
|
|
|
|
The frame interval is calculated using the following equation::
|
|
|
|
frame interval = (analogue crop width + horizontal blanking) *
|
|
(analogue crop height + vertical blanking) / pixel rate
|
|
|
|
The formula is bus independent and is applicable for raw timing parameters on
|
|
large variety of devices beyond camera sensors. Devices that have no analogue
|
|
crop, use the full source image size, i.e. pixel array size.
|
|
|
|
Horizontal and vertical blanking are specified by ``V4L2_CID_HBLANK`` and
|
|
``V4L2_CID_VBLANK``, respectively. The unit of these controls are lines. The
|
|
pixel rate is specified by ``V4L2_CID_PIXEL_RATE`` in the same sub-device. The
|
|
unit of that control is Hz.
|
|
|
|
Register list based drivers need to implement read-only sub-device nodes for the
|
|
purpose. Devices that are not register list based need these to configure the
|
|
device's internal processing pipeline.
|
|
|
|
The first entity in the linear pipeline is the pixel array. The pixel array may
|
|
be followed by other entities that are there to allow configuring binning,
|
|
skipping, scaling or digital crop :ref:`v4l2-subdev-selections`.
|
|
|
|
USB cameras etc. devices
|
|
~~~~~~~~~~~~~~~~~~~~~~~~
|
|
|
|
USB video class hardware, as well as many cameras offering a similar higher
|
|
level interface natively, generally use the concept of frame interval (or frame
|
|
rate) on device level in firmware or hardware. This means lower level controls
|
|
implemented by raw cameras may not be used on uAPI (or even kAPI) to control the
|
|
frame interval on these devices.
|
|
|
|
Power management
|
|
----------------
|
|
|
|
Always use runtime PM to manage the power states of your device. Camera sensor
|
|
drivers are in no way special in this respect: they are responsible for
|
|
controlling the power state of the device they otherwise control as well. In
|
|
general, the device must be powered on at least when its registers are being
|
|
accessed and when it is streaming.
|
|
|
|
Existing camera sensor drivers may rely on the old
|
|
:c:type:`v4l2_subdev_core_ops`->s_power() callback for bridge or ISP drivers to
|
|
manage their power state. This is however **deprecated**. If you feel you need
|
|
to begin calling an s_power from an ISP or a bridge driver, instead please add
|
|
runtime PM support to the sensor driver you are using. Likewise, new drivers
|
|
should not use s_power.
|
|
|
|
Please see examples in e.g. ``drivers/media/i2c/ov8856.c`` and
|
|
``drivers/media/i2c/smiapp/smiapp-core.c``. The two drivers work in both ACPI
|
|
and DT based systems.
|
|
|
|
Control framework
|
|
~~~~~~~~~~~~~~~~~
|
|
|
|
``v4l2_ctrl_handler_setup()`` function may not be used in the device's runtime
|
|
PM ``runtime_resume`` callback, as it has no way to figure out the power state
|
|
of the device. This is because the power state of the device is only changed
|
|
after the power state transition has taken place. The ``s_ctrl`` callback can be
|
|
used to obtain device's power state after the power state transition:
|
|
|
|
.. c:function::
|
|
int pm_runtime_get_if_in_use(struct device *dev);
|
|
|
|
The function returns a non-zero value if it succeeded getting the power count or
|
|
runtime PM was disabled, in either of which cases the driver may proceed to
|
|
access the device.
|
|
|
|
Controls
|
|
--------
|
|
|
|
For camera sensors that are connected to a bus where transmitter and receiver
|
|
require common configuration set by drivers, such as CSI-2 or parallel (BT.601
|
|
or BT.656) bus, the ``V4L2_CID_LINK_FREQ`` control is mandatory on transmitter
|
|
drivers. Receiver drivers can use the ``V4L2_CID_LINK_FREQ`` to query the
|
|
frequency used on the bus.
|
|
|
|
The transmitter drivers should also implement ``V4L2_CID_PIXEL_RATE`` control in
|
|
order to tell the maximum pixel rate to the receiver. This is required on raw
|
|
camera sensors.
|