1850 lines
49 KiB
C
1850 lines
49 KiB
C
// SPDX-License-Identifier: GPL-2.0
|
|
//
|
|
// tvp5150 - Texas Instruments TVP5150A/AM1 and TVP5151 video decoder driver
|
|
//
|
|
// Copyright (c) 2005,2006 Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
|
|
#include <dt-bindings/media/tvp5150.h>
|
|
#include <linux/i2c.h>
|
|
#include <linux/slab.h>
|
|
#include <linux/videodev2.h>
|
|
#include <linux/delay.h>
|
|
#include <linux/gpio/consumer.h>
|
|
#include <linux/interrupt.h>
|
|
#include <linux/module.h>
|
|
#include <linux/of_graph.h>
|
|
#include <linux/regmap.h>
|
|
#include <media/v4l2-async.h>
|
|
#include <media/v4l2-device.h>
|
|
#include <media/v4l2-ctrls.h>
|
|
#include <media/v4l2-fwnode.h>
|
|
#include <media/v4l2-mc.h>
|
|
|
|
#include "tvp5150_reg.h"
|
|
|
|
#define TVP5150_H_MAX 720U
|
|
#define TVP5150_V_MAX_525_60 480U
|
|
#define TVP5150_V_MAX_OTHERS 576U
|
|
#define TVP5150_MAX_CROP_LEFT 511
|
|
#define TVP5150_MAX_CROP_TOP 127
|
|
#define TVP5150_CROP_SHIFT 2
|
|
#define TVP5150_MBUS_FMT MEDIA_BUS_FMT_UYVY8_2X8
|
|
#define TVP5150_FIELD V4L2_FIELD_ALTERNATE
|
|
#define TVP5150_COLORSPACE V4L2_COLORSPACE_SMPTE170M
|
|
|
|
MODULE_DESCRIPTION("Texas Instruments TVP5150A/TVP5150AM1/TVP5151 video decoder driver");
|
|
MODULE_AUTHOR("Mauro Carvalho Chehab");
|
|
MODULE_LICENSE("GPL v2");
|
|
|
|
|
|
static int debug;
|
|
module_param(debug, int, 0644);
|
|
MODULE_PARM_DESC(debug, "Debug level (0-2)");
|
|
|
|
#define dprintk0(__dev, __arg...) dev_dbg_lvl(__dev, 0, 0, __arg)
|
|
|
|
enum tvp5150_pads {
|
|
TVP5150_PAD_IF_INPUT,
|
|
TVP5150_PAD_VID_OUT,
|
|
TVP5150_NUM_PADS
|
|
};
|
|
|
|
struct tvp5150 {
|
|
struct v4l2_subdev sd;
|
|
#ifdef CONFIG_MEDIA_CONTROLLER
|
|
struct media_pad pads[TVP5150_NUM_PADS];
|
|
struct media_entity input_ent[TVP5150_INPUT_NUM];
|
|
struct media_pad input_pad[TVP5150_INPUT_NUM];
|
|
#endif
|
|
struct v4l2_ctrl_handler hdl;
|
|
struct v4l2_rect rect;
|
|
struct regmap *regmap;
|
|
int irq;
|
|
|
|
v4l2_std_id norm; /* Current set standard */
|
|
v4l2_std_id detected_norm;
|
|
u32 input;
|
|
u32 output;
|
|
u32 oe;
|
|
int enable;
|
|
bool lock;
|
|
|
|
u16 dev_id;
|
|
u16 rom_ver;
|
|
|
|
enum v4l2_mbus_type mbus_type;
|
|
};
|
|
|
|
static inline struct tvp5150 *to_tvp5150(struct v4l2_subdev *sd)
|
|
{
|
|
return container_of(sd, struct tvp5150, sd);
|
|
}
|
|
|
|
static inline struct v4l2_subdev *to_sd(struct v4l2_ctrl *ctrl)
|
|
{
|
|
return &container_of(ctrl->handler, struct tvp5150, hdl)->sd;
|
|
}
|
|
|
|
static int tvp5150_read(struct v4l2_subdev *sd, unsigned char addr)
|
|
{
|
|
struct tvp5150 *decoder = to_tvp5150(sd);
|
|
int ret, val;
|
|
|
|
ret = regmap_read(decoder->regmap, addr, &val);
|
|
if (ret < 0)
|
|
return ret;
|
|
|
|
return val;
|
|
}
|
|
|
|
static void dump_reg_range(struct v4l2_subdev *sd, char *s, u8 init,
|
|
const u8 end, int max_line)
|
|
{
|
|
u8 buf[16];
|
|
int i = 0, j, len;
|
|
|
|
if (max_line > 16) {
|
|
dprintk0(sd->dev, "too much data to dump\n");
|
|
return;
|
|
}
|
|
|
|
for (i = init; i < end; i += max_line) {
|
|
len = (end - i > max_line) ? max_line : end - i;
|
|
|
|
for (j = 0; j < len; j++)
|
|
buf[j] = tvp5150_read(sd, i + j);
|
|
|
|
dprintk0(sd->dev, "%s reg %02x = %*ph\n", s, i, len, buf);
|
|
}
|
|
}
|
|
|
|
static int tvp5150_log_status(struct v4l2_subdev *sd)
|
|
{
|
|
dprintk0(sd->dev, "tvp5150: Video input source selection #1 = 0x%02x\n",
|
|
tvp5150_read(sd, TVP5150_VD_IN_SRC_SEL_1));
|
|
dprintk0(sd->dev, "tvp5150: Analog channel controls = 0x%02x\n",
|
|
tvp5150_read(sd, TVP5150_ANAL_CHL_CTL));
|
|
dprintk0(sd->dev, "tvp5150: Operation mode controls = 0x%02x\n",
|
|
tvp5150_read(sd, TVP5150_OP_MODE_CTL));
|
|
dprintk0(sd->dev, "tvp5150: Miscellaneous controls = 0x%02x\n",
|
|
tvp5150_read(sd, TVP5150_MISC_CTL));
|
|
dprintk0(sd->dev, "tvp5150: Autoswitch mask= 0x%02x\n",
|
|
tvp5150_read(sd, TVP5150_AUTOSW_MSK));
|
|
dprintk0(sd->dev, "tvp5150: Color killer threshold control = 0x%02x\n",
|
|
tvp5150_read(sd, TVP5150_COLOR_KIL_THSH_CTL));
|
|
dprintk0(sd->dev, "tvp5150: Luminance processing controls #1 #2 and #3 = %02x %02x %02x\n",
|
|
tvp5150_read(sd, TVP5150_LUMA_PROC_CTL_1),
|
|
tvp5150_read(sd, TVP5150_LUMA_PROC_CTL_2),
|
|
tvp5150_read(sd, TVP5150_LUMA_PROC_CTL_3));
|
|
dprintk0(sd->dev, "tvp5150: Brightness control = 0x%02x\n",
|
|
tvp5150_read(sd, TVP5150_BRIGHT_CTL));
|
|
dprintk0(sd->dev, "tvp5150: Color saturation control = 0x%02x\n",
|
|
tvp5150_read(sd, TVP5150_SATURATION_CTL));
|
|
dprintk0(sd->dev, "tvp5150: Hue control = 0x%02x\n",
|
|
tvp5150_read(sd, TVP5150_HUE_CTL));
|
|
dprintk0(sd->dev, "tvp5150: Contrast control = 0x%02x\n",
|
|
tvp5150_read(sd, TVP5150_CONTRAST_CTL));
|
|
dprintk0(sd->dev, "tvp5150: Outputs and data rates select = 0x%02x\n",
|
|
tvp5150_read(sd, TVP5150_DATA_RATE_SEL));
|
|
dprintk0(sd->dev, "tvp5150: Configuration shared pins = 0x%02x\n",
|
|
tvp5150_read(sd, TVP5150_CONF_SHARED_PIN));
|
|
dprintk0(sd->dev, "tvp5150: Active video cropping start = 0x%02x%02x\n",
|
|
tvp5150_read(sd, TVP5150_ACT_VD_CROP_ST_MSB),
|
|
tvp5150_read(sd, TVP5150_ACT_VD_CROP_ST_LSB));
|
|
dprintk0(sd->dev, "tvp5150: Active video cropping stop = 0x%02x%02x\n",
|
|
tvp5150_read(sd, TVP5150_ACT_VD_CROP_STP_MSB),
|
|
tvp5150_read(sd, TVP5150_ACT_VD_CROP_STP_LSB));
|
|
dprintk0(sd->dev, "tvp5150: Genlock/RTC = 0x%02x\n",
|
|
tvp5150_read(sd, TVP5150_GENLOCK));
|
|
dprintk0(sd->dev, "tvp5150: Horizontal sync start = 0x%02x\n",
|
|
tvp5150_read(sd, TVP5150_HORIZ_SYNC_START));
|
|
dprintk0(sd->dev, "tvp5150: Vertical blanking start = 0x%02x\n",
|
|
tvp5150_read(sd, TVP5150_VERT_BLANKING_START));
|
|
dprintk0(sd->dev, "tvp5150: Vertical blanking stop = 0x%02x\n",
|
|
tvp5150_read(sd, TVP5150_VERT_BLANKING_STOP));
|
|
dprintk0(sd->dev, "tvp5150: Chrominance processing control #1 and #2 = %02x %02x\n",
|
|
tvp5150_read(sd, TVP5150_CHROMA_PROC_CTL_1),
|
|
tvp5150_read(sd, TVP5150_CHROMA_PROC_CTL_2));
|
|
dprintk0(sd->dev, "tvp5150: Interrupt reset register B = 0x%02x\n",
|
|
tvp5150_read(sd, TVP5150_INT_RESET_REG_B));
|
|
dprintk0(sd->dev, "tvp5150: Interrupt enable register B = 0x%02x\n",
|
|
tvp5150_read(sd, TVP5150_INT_ENABLE_REG_B));
|
|
dprintk0(sd->dev, "tvp5150: Interrupt configuration register B = 0x%02x\n",
|
|
tvp5150_read(sd, TVP5150_INTT_CONFIG_REG_B));
|
|
dprintk0(sd->dev, "tvp5150: Video standard = 0x%02x\n",
|
|
tvp5150_read(sd, TVP5150_VIDEO_STD));
|
|
dprintk0(sd->dev, "tvp5150: Chroma gain factor: Cb=0x%02x Cr=0x%02x\n",
|
|
tvp5150_read(sd, TVP5150_CB_GAIN_FACT),
|
|
tvp5150_read(sd, TVP5150_CR_GAIN_FACTOR));
|
|
dprintk0(sd->dev, "tvp5150: Macrovision on counter = 0x%02x\n",
|
|
tvp5150_read(sd, TVP5150_MACROVISION_ON_CTR));
|
|
dprintk0(sd->dev, "tvp5150: Macrovision off counter = 0x%02x\n",
|
|
tvp5150_read(sd, TVP5150_MACROVISION_OFF_CTR));
|
|
dprintk0(sd->dev, "tvp5150: ITU-R BT.656.%d timing(TVP5150AM1 only)\n",
|
|
(tvp5150_read(sd, TVP5150_REV_SELECT) & 1) ? 3 : 4);
|
|
dprintk0(sd->dev, "tvp5150: Device ID = %02x%02x\n",
|
|
tvp5150_read(sd, TVP5150_MSB_DEV_ID),
|
|
tvp5150_read(sd, TVP5150_LSB_DEV_ID));
|
|
dprintk0(sd->dev, "tvp5150: ROM version = (hex) %02x.%02x\n",
|
|
tvp5150_read(sd, TVP5150_ROM_MAJOR_VER),
|
|
tvp5150_read(sd, TVP5150_ROM_MINOR_VER));
|
|
dprintk0(sd->dev, "tvp5150: Vertical line count = 0x%02x%02x\n",
|
|
tvp5150_read(sd, TVP5150_VERT_LN_COUNT_MSB),
|
|
tvp5150_read(sd, TVP5150_VERT_LN_COUNT_LSB));
|
|
dprintk0(sd->dev, "tvp5150: Interrupt status register B = 0x%02x\n",
|
|
tvp5150_read(sd, TVP5150_INT_STATUS_REG_B));
|
|
dprintk0(sd->dev, "tvp5150: Interrupt active register B = 0x%02x\n",
|
|
tvp5150_read(sd, TVP5150_INT_ACTIVE_REG_B));
|
|
dprintk0(sd->dev, "tvp5150: Status regs #1 to #5 = %02x %02x %02x %02x %02x\n",
|
|
tvp5150_read(sd, TVP5150_STATUS_REG_1),
|
|
tvp5150_read(sd, TVP5150_STATUS_REG_2),
|
|
tvp5150_read(sd, TVP5150_STATUS_REG_3),
|
|
tvp5150_read(sd, TVP5150_STATUS_REG_4),
|
|
tvp5150_read(sd, TVP5150_STATUS_REG_5));
|
|
|
|
dump_reg_range(sd, "Teletext filter 1", TVP5150_TELETEXT_FIL1_INI,
|
|
TVP5150_TELETEXT_FIL1_END, 8);
|
|
dump_reg_range(sd, "Teletext filter 2", TVP5150_TELETEXT_FIL2_INI,
|
|
TVP5150_TELETEXT_FIL2_END, 8);
|
|
|
|
dprintk0(sd->dev, "tvp5150: Teletext filter enable = 0x%02x\n",
|
|
tvp5150_read(sd, TVP5150_TELETEXT_FIL_ENA));
|
|
dprintk0(sd->dev, "tvp5150: Interrupt status register A = 0x%02x\n",
|
|
tvp5150_read(sd, TVP5150_INT_STATUS_REG_A));
|
|
dprintk0(sd->dev, "tvp5150: Interrupt enable register A = 0x%02x\n",
|
|
tvp5150_read(sd, TVP5150_INT_ENABLE_REG_A));
|
|
dprintk0(sd->dev, "tvp5150: Interrupt configuration = 0x%02x\n",
|
|
tvp5150_read(sd, TVP5150_INT_CONF));
|
|
dprintk0(sd->dev, "tvp5150: VDP status register = 0x%02x\n",
|
|
tvp5150_read(sd, TVP5150_VDP_STATUS_REG));
|
|
dprintk0(sd->dev, "tvp5150: FIFO word count = 0x%02x\n",
|
|
tvp5150_read(sd, TVP5150_FIFO_WORD_COUNT));
|
|
dprintk0(sd->dev, "tvp5150: FIFO interrupt threshold = 0x%02x\n",
|
|
tvp5150_read(sd, TVP5150_FIFO_INT_THRESHOLD));
|
|
dprintk0(sd->dev, "tvp5150: FIFO reset = 0x%02x\n",
|
|
tvp5150_read(sd, TVP5150_FIFO_RESET));
|
|
dprintk0(sd->dev, "tvp5150: Line number interrupt = 0x%02x\n",
|
|
tvp5150_read(sd, TVP5150_LINE_NUMBER_INT));
|
|
dprintk0(sd->dev, "tvp5150: Pixel alignment register = 0x%02x%02x\n",
|
|
tvp5150_read(sd, TVP5150_PIX_ALIGN_REG_HIGH),
|
|
tvp5150_read(sd, TVP5150_PIX_ALIGN_REG_LOW));
|
|
dprintk0(sd->dev, "tvp5150: FIFO output control = 0x%02x\n",
|
|
tvp5150_read(sd, TVP5150_FIFO_OUT_CTRL));
|
|
dprintk0(sd->dev, "tvp5150: Full field enable = 0x%02x\n",
|
|
tvp5150_read(sd, TVP5150_FULL_FIELD_ENA));
|
|
dprintk0(sd->dev, "tvp5150: Full field mode register = 0x%02x\n",
|
|
tvp5150_read(sd, TVP5150_FULL_FIELD_MODE_REG));
|
|
|
|
dump_reg_range(sd, "CC data", TVP5150_CC_DATA_INI,
|
|
TVP5150_CC_DATA_END, 8);
|
|
|
|
dump_reg_range(sd, "WSS data", TVP5150_WSS_DATA_INI,
|
|
TVP5150_WSS_DATA_END, 8);
|
|
|
|
dump_reg_range(sd, "VPS data", TVP5150_VPS_DATA_INI,
|
|
TVP5150_VPS_DATA_END, 8);
|
|
|
|
dump_reg_range(sd, "VITC data", TVP5150_VITC_DATA_INI,
|
|
TVP5150_VITC_DATA_END, 10);
|
|
|
|
dump_reg_range(sd, "Line mode", TVP5150_LINE_MODE_INI,
|
|
TVP5150_LINE_MODE_END, 8);
|
|
return 0;
|
|
}
|
|
|
|
/****************************************************************************
|
|
Basic functions
|
|
****************************************************************************/
|
|
|
|
static void tvp5150_selmux(struct v4l2_subdev *sd)
|
|
{
|
|
int opmode = 0;
|
|
struct tvp5150 *decoder = to_tvp5150(sd);
|
|
unsigned int mask, val;
|
|
int input = 0;
|
|
|
|
/* Only tvp5150am1 and tvp5151 have signal generator support */
|
|
if ((decoder->dev_id == 0x5150 && decoder->rom_ver == 0x0400) ||
|
|
(decoder->dev_id == 0x5151 && decoder->rom_ver == 0x0100)) {
|
|
if (!decoder->enable)
|
|
input = 8;
|
|
}
|
|
|
|
switch (decoder->input) {
|
|
case TVP5150_COMPOSITE1:
|
|
input |= 2;
|
|
/* fall through */
|
|
case TVP5150_COMPOSITE0:
|
|
break;
|
|
case TVP5150_SVIDEO:
|
|
default:
|
|
input |= 1;
|
|
break;
|
|
}
|
|
|
|
dev_dbg_lvl(sd->dev, 1, debug, "Selecting video route: route input=%i, output=%i => tvp5150 input=%i, opmode=%i\n",
|
|
decoder->input, decoder->output,
|
|
input, opmode);
|
|
|
|
regmap_write(decoder->regmap, TVP5150_OP_MODE_CTL, opmode);
|
|
regmap_write(decoder->regmap, TVP5150_VD_IN_SRC_SEL_1, input);
|
|
|
|
/*
|
|
* Setup the FID/GLCO/VLK/HVLK and INTREQ/GPCL/VBLK output signals. For
|
|
* S-Video we output the vertical lock (VLK) signal on FID/GLCO/VLK/HVLK
|
|
* and set INTREQ/GPCL/VBLK to logic 0. For composite we output the
|
|
* field indicator (FID) signal on FID/GLCO/VLK/HVLK and set
|
|
* INTREQ/GPCL/VBLK to logic 1.
|
|
*/
|
|
mask = TVP5150_MISC_CTL_GPCL | TVP5150_MISC_CTL_HVLK;
|
|
if (decoder->input == TVP5150_SVIDEO)
|
|
val = TVP5150_MISC_CTL_HVLK;
|
|
else
|
|
val = TVP5150_MISC_CTL_GPCL;
|
|
regmap_update_bits(decoder->regmap, TVP5150_MISC_CTL, mask, val);
|
|
};
|
|
|
|
struct i2c_reg_value {
|
|
unsigned char reg;
|
|
unsigned char value;
|
|
};
|
|
|
|
/* Default values as sugested at TVP5150AM1 datasheet */
|
|
static const struct i2c_reg_value tvp5150_init_default[] = {
|
|
{ /* 0x00 */
|
|
TVP5150_VD_IN_SRC_SEL_1, 0x00
|
|
},
|
|
{ /* 0x01 */
|
|
TVP5150_ANAL_CHL_CTL, 0x15
|
|
},
|
|
{ /* 0x02 */
|
|
TVP5150_OP_MODE_CTL, 0x00
|
|
},
|
|
{ /* 0x03 */
|
|
TVP5150_MISC_CTL, 0x01
|
|
},
|
|
{ /* 0x06 */
|
|
TVP5150_COLOR_KIL_THSH_CTL, 0x10
|
|
},
|
|
{ /* 0x07 */
|
|
TVP5150_LUMA_PROC_CTL_1, 0x60
|
|
},
|
|
{ /* 0x08 */
|
|
TVP5150_LUMA_PROC_CTL_2, 0x00
|
|
},
|
|
{ /* 0x09 */
|
|
TVP5150_BRIGHT_CTL, 0x80
|
|
},
|
|
{ /* 0x0a */
|
|
TVP5150_SATURATION_CTL, 0x80
|
|
},
|
|
{ /* 0x0b */
|
|
TVP5150_HUE_CTL, 0x00
|
|
},
|
|
{ /* 0x0c */
|
|
TVP5150_CONTRAST_CTL, 0x80
|
|
},
|
|
{ /* 0x0d */
|
|
TVP5150_DATA_RATE_SEL, 0x47
|
|
},
|
|
{ /* 0x0e */
|
|
TVP5150_LUMA_PROC_CTL_3, 0x00
|
|
},
|
|
{ /* 0x0f */
|
|
TVP5150_CONF_SHARED_PIN, 0x08
|
|
},
|
|
{ /* 0x11 */
|
|
TVP5150_ACT_VD_CROP_ST_MSB, 0x00
|
|
},
|
|
{ /* 0x12 */
|
|
TVP5150_ACT_VD_CROP_ST_LSB, 0x00
|
|
},
|
|
{ /* 0x13 */
|
|
TVP5150_ACT_VD_CROP_STP_MSB, 0x00
|
|
},
|
|
{ /* 0x14 */
|
|
TVP5150_ACT_VD_CROP_STP_LSB, 0x00
|
|
},
|
|
{ /* 0x15 */
|
|
TVP5150_GENLOCK, 0x01
|
|
},
|
|
{ /* 0x16 */
|
|
TVP5150_HORIZ_SYNC_START, 0x80
|
|
},
|
|
{ /* 0x18 */
|
|
TVP5150_VERT_BLANKING_START, 0x00
|
|
},
|
|
{ /* 0x19 */
|
|
TVP5150_VERT_BLANKING_STOP, 0x00
|
|
},
|
|
{ /* 0x1a */
|
|
TVP5150_CHROMA_PROC_CTL_1, 0x0c
|
|
},
|
|
{ /* 0x1b */
|
|
TVP5150_CHROMA_PROC_CTL_2, 0x14
|
|
},
|
|
{ /* 0x1c */
|
|
TVP5150_INT_RESET_REG_B, 0x00
|
|
},
|
|
{ /* 0x1d */
|
|
TVP5150_INT_ENABLE_REG_B, 0x00
|
|
},
|
|
{ /* 0x1e */
|
|
TVP5150_INTT_CONFIG_REG_B, 0x00
|
|
},
|
|
{ /* 0x28 */
|
|
TVP5150_VIDEO_STD, 0x00
|
|
},
|
|
{ /* 0x2e */
|
|
TVP5150_MACROVISION_ON_CTR, 0x0f
|
|
},
|
|
{ /* 0x2f */
|
|
TVP5150_MACROVISION_OFF_CTR, 0x01
|
|
},
|
|
{ /* 0xbb */
|
|
TVP5150_TELETEXT_FIL_ENA, 0x00
|
|
},
|
|
{ /* 0xc0 */
|
|
TVP5150_INT_STATUS_REG_A, 0x00
|
|
},
|
|
{ /* 0xc1 */
|
|
TVP5150_INT_ENABLE_REG_A, 0x00
|
|
},
|
|
{ /* 0xc2 */
|
|
TVP5150_INT_CONF, 0x04
|
|
},
|
|
{ /* 0xc8 */
|
|
TVP5150_FIFO_INT_THRESHOLD, 0x80
|
|
},
|
|
{ /* 0xc9 */
|
|
TVP5150_FIFO_RESET, 0x00
|
|
},
|
|
{ /* 0xca */
|
|
TVP5150_LINE_NUMBER_INT, 0x00
|
|
},
|
|
{ /* 0xcb */
|
|
TVP5150_PIX_ALIGN_REG_LOW, 0x4e
|
|
},
|
|
{ /* 0xcc */
|
|
TVP5150_PIX_ALIGN_REG_HIGH, 0x00
|
|
},
|
|
{ /* 0xcd */
|
|
TVP5150_FIFO_OUT_CTRL, 0x01
|
|
},
|
|
{ /* 0xcf */
|
|
TVP5150_FULL_FIELD_ENA, 0x00
|
|
},
|
|
{ /* 0xd0 */
|
|
TVP5150_LINE_MODE_INI, 0x00
|
|
},
|
|
{ /* 0xfc */
|
|
TVP5150_FULL_FIELD_MODE_REG, 0x7f
|
|
},
|
|
{ /* end of data */
|
|
0xff, 0xff
|
|
}
|
|
};
|
|
|
|
/* Default values as sugested at TVP5150AM1 datasheet */
|
|
static const struct i2c_reg_value tvp5150_init_enable[] = {
|
|
{ /* Automatic offset and AGC enabled */
|
|
TVP5150_ANAL_CHL_CTL, 0x15
|
|
}, { /* Activate YCrCb output 0x9 or 0xd ? */
|
|
TVP5150_MISC_CTL, TVP5150_MISC_CTL_GPCL |
|
|
TVP5150_MISC_CTL_INTREQ_OE |
|
|
TVP5150_MISC_CTL_YCBCR_OE |
|
|
TVP5150_MISC_CTL_SYNC_OE |
|
|
TVP5150_MISC_CTL_VBLANK |
|
|
TVP5150_MISC_CTL_CLOCK_OE,
|
|
}, { /* Activates video std autodetection for all standards */
|
|
TVP5150_AUTOSW_MSK, 0x0
|
|
}, { /* Default format: 0x47. For 4:2:2: 0x40 */
|
|
TVP5150_DATA_RATE_SEL, 0x47
|
|
}, {
|
|
TVP5150_CHROMA_PROC_CTL_1, 0x0c
|
|
}, {
|
|
TVP5150_CHROMA_PROC_CTL_2, 0x54
|
|
}, { /* Non documented, but initialized on WinTV USB2 */
|
|
0x27, 0x20
|
|
}, {
|
|
0xff, 0xff
|
|
}
|
|
};
|
|
|
|
struct tvp5150_vbi_type {
|
|
unsigned int vbi_type;
|
|
unsigned int ini_line;
|
|
unsigned int end_line;
|
|
unsigned int by_field :1;
|
|
};
|
|
|
|
struct i2c_vbi_ram_value {
|
|
u16 reg;
|
|
struct tvp5150_vbi_type type;
|
|
unsigned char values[16];
|
|
};
|
|
|
|
/* This struct have the values for each supported VBI Standard
|
|
* by
|
|
tvp5150_vbi_types should follow the same order as vbi_ram_default
|
|
* value 0 means rom position 0x10, value 1 means rom position 0x30
|
|
* and so on. There are 16 possible locations from 0 to 15.
|
|
*/
|
|
|
|
static struct i2c_vbi_ram_value vbi_ram_default[] = {
|
|
|
|
/*
|
|
* FIXME: Current api doesn't handle all VBI types, those not
|
|
* yet supported are placed under #if 0
|
|
*/
|
|
#if 0
|
|
[0] = {0x010, /* Teletext, SECAM, WST System A */
|
|
{V4L2_SLICED_TELETEXT_SECAM, 6, 23, 1},
|
|
{ 0xaa, 0xaa, 0xff, 0xff, 0xe7, 0x2e, 0x20, 0x26,
|
|
0xe6, 0xb4, 0x0e, 0x00, 0x00, 0x00, 0x10, 0x00 }
|
|
},
|
|
#endif
|
|
[1] = {0x030, /* Teletext, PAL, WST System B */
|
|
{V4L2_SLICED_TELETEXT_B, 6, 22, 1},
|
|
{ 0xaa, 0xaa, 0xff, 0xff, 0x27, 0x2e, 0x20, 0x2b,
|
|
0xa6, 0x72, 0x10, 0x00, 0x00, 0x00, 0x10, 0x00 }
|
|
},
|
|
#if 0
|
|
[2] = {0x050, /* Teletext, PAL, WST System C */
|
|
{V4L2_SLICED_TELETEXT_PAL_C, 6, 22, 1},
|
|
{ 0xaa, 0xaa, 0xff, 0xff, 0xe7, 0x2e, 0x20, 0x22,
|
|
0xa6, 0x98, 0x0d, 0x00, 0x00, 0x00, 0x10, 0x00 }
|
|
},
|
|
[3] = {0x070, /* Teletext, NTSC, WST System B */
|
|
{V4L2_SLICED_TELETEXT_NTSC_B, 10, 21, 1},
|
|
{ 0xaa, 0xaa, 0xff, 0xff, 0x27, 0x2e, 0x20, 0x23,
|
|
0x69, 0x93, 0x0d, 0x00, 0x00, 0x00, 0x10, 0x00 }
|
|
},
|
|
[4] = {0x090, /* Tetetext, NTSC NABTS System C */
|
|
{V4L2_SLICED_TELETEXT_NTSC_C, 10, 21, 1},
|
|
{ 0xaa, 0xaa, 0xff, 0xff, 0xe7, 0x2e, 0x20, 0x22,
|
|
0x69, 0x93, 0x0d, 0x00, 0x00, 0x00, 0x15, 0x00 }
|
|
},
|
|
[5] = {0x0b0, /* Teletext, NTSC-J, NABTS System D */
|
|
{V4L2_SLICED_TELETEXT_NTSC_D, 10, 21, 1},
|
|
{ 0xaa, 0xaa, 0xff, 0xff, 0xa7, 0x2e, 0x20, 0x23,
|
|
0x69, 0x93, 0x0d, 0x00, 0x00, 0x00, 0x10, 0x00 }
|
|
},
|
|
[6] = {0x0d0, /* Closed Caption, PAL/SECAM */
|
|
{V4L2_SLICED_CAPTION_625, 22, 22, 1},
|
|
{ 0xaa, 0x2a, 0xff, 0x3f, 0x04, 0x51, 0x6e, 0x02,
|
|
0xa6, 0x7b, 0x09, 0x00, 0x00, 0x00, 0x27, 0x00 }
|
|
},
|
|
#endif
|
|
[7] = {0x0f0, /* Closed Caption, NTSC */
|
|
{V4L2_SLICED_CAPTION_525, 21, 21, 1},
|
|
{ 0xaa, 0x2a, 0xff, 0x3f, 0x04, 0x51, 0x6e, 0x02,
|
|
0x69, 0x8c, 0x09, 0x00, 0x00, 0x00, 0x27, 0x00 }
|
|
},
|
|
[8] = {0x110, /* Wide Screen Signal, PAL/SECAM */
|
|
{V4L2_SLICED_WSS_625, 23, 23, 1},
|
|
{ 0x5b, 0x55, 0xc5, 0xff, 0x00, 0x71, 0x6e, 0x42,
|
|
0xa6, 0xcd, 0x0f, 0x00, 0x00, 0x00, 0x3a, 0x00 }
|
|
},
|
|
#if 0
|
|
[9] = {0x130, /* Wide Screen Signal, NTSC C */
|
|
{V4L2_SLICED_WSS_525, 20, 20, 1},
|
|
{ 0x38, 0x00, 0x3f, 0x00, 0x00, 0x71, 0x6e, 0x43,
|
|
0x69, 0x7c, 0x08, 0x00, 0x00, 0x00, 0x39, 0x00 }
|
|
},
|
|
[10] = {0x150, /* Vertical Interval Timecode (VITC), PAL/SECAM */
|
|
{V4l2_SLICED_VITC_625, 6, 22, 0},
|
|
{ 0x00, 0x00, 0x00, 0x00, 0x00, 0x8f, 0x6d, 0x49,
|
|
0xa6, 0x85, 0x08, 0x00, 0x00, 0x00, 0x4c, 0x00 }
|
|
},
|
|
[11] = {0x170, /* Vertical Interval Timecode (VITC), NTSC */
|
|
{V4l2_SLICED_VITC_525, 10, 20, 0},
|
|
{ 0x00, 0x00, 0x00, 0x00, 0x00, 0x8f, 0x6d, 0x49,
|
|
0x69, 0x94, 0x08, 0x00, 0x00, 0x00, 0x4c, 0x00 }
|
|
},
|
|
#endif
|
|
[12] = {0x190, /* Video Program System (VPS), PAL */
|
|
{V4L2_SLICED_VPS, 16, 16, 0},
|
|
{ 0xaa, 0xaa, 0xff, 0xff, 0xba, 0xce, 0x2b, 0x0d,
|
|
0xa6, 0xda, 0x0b, 0x00, 0x00, 0x00, 0x60, 0x00 }
|
|
},
|
|
/* 0x1d0 User programmable */
|
|
};
|
|
|
|
static int tvp5150_write_inittab(struct v4l2_subdev *sd,
|
|
const struct i2c_reg_value *regs)
|
|
{
|
|
struct tvp5150 *decoder = to_tvp5150(sd);
|
|
|
|
while (regs->reg != 0xff) {
|
|
regmap_write(decoder->regmap, regs->reg, regs->value);
|
|
regs++;
|
|
}
|
|
return 0;
|
|
}
|
|
|
|
static int tvp5150_vdp_init(struct v4l2_subdev *sd)
|
|
{
|
|
struct tvp5150 *decoder = to_tvp5150(sd);
|
|
struct regmap *map = decoder->regmap;
|
|
unsigned int i;
|
|
int j;
|
|
|
|
/* Disable Full Field */
|
|
regmap_write(map, TVP5150_FULL_FIELD_ENA, 0);
|
|
|
|
/* Before programming, Line mode should be at 0xff */
|
|
for (i = TVP5150_LINE_MODE_INI; i <= TVP5150_LINE_MODE_END; i++)
|
|
regmap_write(map, i, 0xff);
|
|
|
|
/* Load Ram Table */
|
|
for (j = 0; j < ARRAY_SIZE(vbi_ram_default); j++) {
|
|
const struct i2c_vbi_ram_value *regs = &vbi_ram_default[j];
|
|
|
|
if (!regs->type.vbi_type)
|
|
continue;
|
|
|
|
regmap_write(map, TVP5150_CONF_RAM_ADDR_HIGH, regs->reg >> 8);
|
|
regmap_write(map, TVP5150_CONF_RAM_ADDR_LOW, regs->reg);
|
|
|
|
for (i = 0; i < 16; i++)
|
|
regmap_write(map, TVP5150_VDP_CONF_RAM_DATA,
|
|
regs->values[i]);
|
|
}
|
|
return 0;
|
|
}
|
|
|
|
/* Fills VBI capabilities based on i2c_vbi_ram_value struct */
|
|
static int tvp5150_g_sliced_vbi_cap(struct v4l2_subdev *sd,
|
|
struct v4l2_sliced_vbi_cap *cap)
|
|
{
|
|
int line, i;
|
|
|
|
dev_dbg_lvl(sd->dev, 1, debug, "g_sliced_vbi_cap\n");
|
|
memset(cap, 0, sizeof(*cap));
|
|
|
|
for (i = 0; i < ARRAY_SIZE(vbi_ram_default); i++) {
|
|
const struct i2c_vbi_ram_value *regs = &vbi_ram_default[i];
|
|
|
|
if (!regs->type.vbi_type)
|
|
continue;
|
|
|
|
for (line = regs->type.ini_line;
|
|
line <= regs->type.end_line;
|
|
line++) {
|
|
cap->service_lines[0][line] |= regs->type.vbi_type;
|
|
}
|
|
cap->service_set |= regs->type.vbi_type;
|
|
}
|
|
return 0;
|
|
}
|
|
|
|
/* Set vbi processing
|
|
* type - one of tvp5150_vbi_types
|
|
* line - line to gather data
|
|
* fields: bit 0 field1, bit 1, field2
|
|
* flags (default=0xf0) is a bitmask, were set means:
|
|
* bit 7: enable filtering null bytes on CC
|
|
* bit 6: send data also to FIFO
|
|
* bit 5: don't allow data with errors on FIFO
|
|
* bit 4: enable ECC when possible
|
|
* pix_align = pix alignment:
|
|
* LSB = field1
|
|
* MSB = field2
|
|
*/
|
|
static int tvp5150_set_vbi(struct v4l2_subdev *sd,
|
|
unsigned int type, u8 flags, int line,
|
|
const int fields)
|
|
{
|
|
struct tvp5150 *decoder = to_tvp5150(sd);
|
|
v4l2_std_id std = decoder->norm;
|
|
u8 reg;
|
|
int i, pos = 0;
|
|
|
|
if (std == V4L2_STD_ALL) {
|
|
dev_err(sd->dev, "VBI can't be configured without knowing number of lines\n");
|
|
return 0;
|
|
} else if (std & V4L2_STD_625_50) {
|
|
/* Don't follow NTSC Line number convension */
|
|
line += 3;
|
|
}
|
|
|
|
if (line < 6 || line > 27)
|
|
return 0;
|
|
|
|
for (i = 0; i < ARRAY_SIZE(vbi_ram_default); i++) {
|
|
const struct i2c_vbi_ram_value *regs = &vbi_ram_default[i];
|
|
|
|
if (!regs->type.vbi_type)
|
|
continue;
|
|
|
|
if ((type & regs->type.vbi_type) &&
|
|
(line >= regs->type.ini_line) &&
|
|
(line <= regs->type.end_line))
|
|
break;
|
|
pos++;
|
|
}
|
|
|
|
type = pos | (flags & 0xf0);
|
|
reg = ((line - 6) << 1) + TVP5150_LINE_MODE_INI;
|
|
|
|
if (fields & 1)
|
|
regmap_write(decoder->regmap, reg, type);
|
|
|
|
if (fields & 2)
|
|
regmap_write(decoder->regmap, reg + 1, type);
|
|
|
|
return type;
|
|
}
|
|
|
|
static int tvp5150_get_vbi(struct v4l2_subdev *sd, int line)
|
|
{
|
|
struct tvp5150 *decoder = to_tvp5150(sd);
|
|
v4l2_std_id std = decoder->norm;
|
|
u8 reg;
|
|
int pos, type = 0;
|
|
int i, ret = 0;
|
|
|
|
if (std == V4L2_STD_ALL) {
|
|
dev_err(sd->dev, "VBI can't be configured without knowing number of lines\n");
|
|
return 0;
|
|
} else if (std & V4L2_STD_625_50) {
|
|
/* Don't follow NTSC Line number convension */
|
|
line += 3;
|
|
}
|
|
|
|
if (line < 6 || line > 27)
|
|
return 0;
|
|
|
|
reg = ((line - 6) << 1) + TVP5150_LINE_MODE_INI;
|
|
|
|
for (i = 0; i <= 1; i++) {
|
|
ret = tvp5150_read(sd, reg + i);
|
|
if (ret < 0) {
|
|
dev_err(sd->dev, "%s: failed with error = %d\n",
|
|
__func__, ret);
|
|
return 0;
|
|
}
|
|
pos = ret & 0x0f;
|
|
if (pos < ARRAY_SIZE(vbi_ram_default))
|
|
type |= vbi_ram_default[pos].type.vbi_type;
|
|
}
|
|
|
|
return type;
|
|
}
|
|
|
|
static int tvp5150_set_std(struct v4l2_subdev *sd, v4l2_std_id std)
|
|
{
|
|
struct tvp5150 *decoder = to_tvp5150(sd);
|
|
int fmt = 0;
|
|
|
|
/* First tests should be against specific std */
|
|
|
|
if (std == V4L2_STD_NTSC_443) {
|
|
fmt = VIDEO_STD_NTSC_4_43_BIT;
|
|
} else if (std == V4L2_STD_PAL_M) {
|
|
fmt = VIDEO_STD_PAL_M_BIT;
|
|
} else if (std == V4L2_STD_PAL_N || std == V4L2_STD_PAL_Nc) {
|
|
fmt = VIDEO_STD_PAL_COMBINATION_N_BIT;
|
|
} else {
|
|
/* Then, test against generic ones */
|
|
if (std & V4L2_STD_NTSC)
|
|
fmt = VIDEO_STD_NTSC_MJ_BIT;
|
|
else if (std & V4L2_STD_PAL)
|
|
fmt = VIDEO_STD_PAL_BDGHIN_BIT;
|
|
else if (std & V4L2_STD_SECAM)
|
|
fmt = VIDEO_STD_SECAM_BIT;
|
|
}
|
|
|
|
dev_dbg_lvl(sd->dev, 1, debug, "Set video std register to %d.\n", fmt);
|
|
regmap_write(decoder->regmap, TVP5150_VIDEO_STD, fmt);
|
|
return 0;
|
|
}
|
|
|
|
static int tvp5150_g_std(struct v4l2_subdev *sd, v4l2_std_id *std)
|
|
{
|
|
struct tvp5150 *decoder = to_tvp5150(sd);
|
|
|
|
*std = decoder->norm;
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int tvp5150_s_std(struct v4l2_subdev *sd, v4l2_std_id std)
|
|
{
|
|
struct tvp5150 *decoder = to_tvp5150(sd);
|
|
|
|
if (decoder->norm == std)
|
|
return 0;
|
|
|
|
/* Change cropping height limits */
|
|
if (std & V4L2_STD_525_60)
|
|
decoder->rect.height = TVP5150_V_MAX_525_60;
|
|
else
|
|
decoder->rect.height = TVP5150_V_MAX_OTHERS;
|
|
|
|
decoder->norm = std;
|
|
|
|
return tvp5150_set_std(sd, std);
|
|
}
|
|
|
|
static v4l2_std_id tvp5150_read_std(struct v4l2_subdev *sd)
|
|
{
|
|
int val = tvp5150_read(sd, TVP5150_STATUS_REG_5);
|
|
|
|
switch (val & 0x0F) {
|
|
case 0x01:
|
|
return V4L2_STD_NTSC;
|
|
case 0x03:
|
|
return V4L2_STD_PAL;
|
|
case 0x05:
|
|
return V4L2_STD_PAL_M;
|
|
case 0x07:
|
|
return V4L2_STD_PAL_N | V4L2_STD_PAL_Nc;
|
|
case 0x09:
|
|
return V4L2_STD_NTSC_443;
|
|
case 0xb:
|
|
return V4L2_STD_SECAM;
|
|
default:
|
|
return V4L2_STD_UNKNOWN;
|
|
}
|
|
}
|
|
|
|
static int query_lock(struct v4l2_subdev *sd)
|
|
{
|
|
struct tvp5150 *decoder = to_tvp5150(sd);
|
|
int status;
|
|
|
|
if (decoder->irq)
|
|
return decoder->lock;
|
|
|
|
regmap_read(decoder->regmap, TVP5150_STATUS_REG_1, &status);
|
|
|
|
/* For standard detection, we need the 3 locks */
|
|
return (status & 0x0e) == 0x0e;
|
|
}
|
|
|
|
static int tvp5150_querystd(struct v4l2_subdev *sd, v4l2_std_id *std_id)
|
|
{
|
|
*std_id = query_lock(sd) ? tvp5150_read_std(sd) : V4L2_STD_UNKNOWN;
|
|
|
|
return 0;
|
|
}
|
|
|
|
static const struct v4l2_event tvp5150_ev_fmt = {
|
|
.type = V4L2_EVENT_SOURCE_CHANGE,
|
|
.u.src_change.changes = V4L2_EVENT_SRC_CH_RESOLUTION,
|
|
};
|
|
|
|
static irqreturn_t tvp5150_isr(int irq, void *dev_id)
|
|
{
|
|
struct tvp5150 *decoder = dev_id;
|
|
struct regmap *map = decoder->regmap;
|
|
unsigned int mask, active = 0, status = 0;
|
|
|
|
mask = TVP5150_MISC_CTL_YCBCR_OE | TVP5150_MISC_CTL_SYNC_OE |
|
|
TVP5150_MISC_CTL_CLOCK_OE;
|
|
|
|
regmap_read(map, TVP5150_INT_STATUS_REG_A, &status);
|
|
if (status) {
|
|
regmap_write(map, TVP5150_INT_STATUS_REG_A, status);
|
|
|
|
if (status & TVP5150_INT_A_LOCK) {
|
|
decoder->lock = !!(status & TVP5150_INT_A_LOCK_STATUS);
|
|
dev_dbg_lvl(decoder->sd.dev, 1, debug,
|
|
"sync lo%s signal\n",
|
|
decoder->lock ? "ck" : "ss");
|
|
v4l2_subdev_notify_event(&decoder->sd, &tvp5150_ev_fmt);
|
|
regmap_update_bits(map, TVP5150_MISC_CTL, mask,
|
|
decoder->lock ? decoder->oe : 0);
|
|
}
|
|
|
|
return IRQ_HANDLED;
|
|
}
|
|
|
|
regmap_read(map, TVP5150_INT_ACTIVE_REG_B, &active);
|
|
if (active) {
|
|
status = 0;
|
|
regmap_read(map, TVP5150_INT_STATUS_REG_B, &status);
|
|
if (status)
|
|
regmap_write(map, TVP5150_INT_RESET_REG_B, status);
|
|
}
|
|
|
|
return IRQ_HANDLED;
|
|
}
|
|
|
|
static int tvp5150_reset(struct v4l2_subdev *sd, u32 val)
|
|
{
|
|
struct tvp5150 *decoder = to_tvp5150(sd);
|
|
struct regmap *map = decoder->regmap;
|
|
|
|
/* Initializes TVP5150 to its default values */
|
|
tvp5150_write_inittab(sd, tvp5150_init_default);
|
|
|
|
if (decoder->irq) {
|
|
/* Configure pins: FID, VSYNC, INTREQ, SCLK */
|
|
regmap_write(map, TVP5150_CONF_SHARED_PIN, 0x0);
|
|
/* Set interrupt polarity to active high */
|
|
regmap_write(map, TVP5150_INT_CONF, TVP5150_VDPOE | 0x1);
|
|
regmap_write(map, TVP5150_INTT_CONFIG_REG_B, 0x1);
|
|
} else {
|
|
/* Configure pins: FID, VSYNC, GPCL/VBLK, SCLK */
|
|
regmap_write(map, TVP5150_CONF_SHARED_PIN, 0x2);
|
|
/* Keep interrupt polarity active low */
|
|
regmap_write(map, TVP5150_INT_CONF, TVP5150_VDPOE);
|
|
regmap_write(map, TVP5150_INTT_CONFIG_REG_B, 0x0);
|
|
}
|
|
|
|
/* Initializes VDP registers */
|
|
tvp5150_vdp_init(sd);
|
|
|
|
/* Selects decoder input */
|
|
tvp5150_selmux(sd);
|
|
|
|
/* Initialize image preferences */
|
|
v4l2_ctrl_handler_setup(&decoder->hdl);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int tvp5150_enable(struct v4l2_subdev *sd)
|
|
{
|
|
struct tvp5150 *decoder = to_tvp5150(sd);
|
|
v4l2_std_id std;
|
|
|
|
/* Initializes TVP5150 to stream enabled values */
|
|
tvp5150_write_inittab(sd, tvp5150_init_enable);
|
|
|
|
if (decoder->norm == V4L2_STD_ALL)
|
|
std = tvp5150_read_std(sd);
|
|
else
|
|
std = decoder->norm;
|
|
|
|
/* Disable autoswitch mode */
|
|
tvp5150_set_std(sd, std);
|
|
|
|
/*
|
|
* Enable the YCbCr and clock outputs. In discrete sync mode
|
|
* (non-BT.656) additionally enable the the sync outputs.
|
|
*/
|
|
switch (decoder->mbus_type) {
|
|
case V4L2_MBUS_PARALLEL:
|
|
/* 8-bit 4:2:2 YUV with discrete sync output */
|
|
regmap_update_bits(decoder->regmap, TVP5150_DATA_RATE_SEL,
|
|
0x7, 0x0);
|
|
decoder->oe = TVP5150_MISC_CTL_YCBCR_OE |
|
|
TVP5150_MISC_CTL_CLOCK_OE |
|
|
TVP5150_MISC_CTL_SYNC_OE;
|
|
break;
|
|
case V4L2_MBUS_BT656:
|
|
decoder->oe = TVP5150_MISC_CTL_YCBCR_OE |
|
|
TVP5150_MISC_CTL_CLOCK_OE;
|
|
break;
|
|
default:
|
|
return -EINVAL;
|
|
}
|
|
|
|
return 0;
|
|
};
|
|
|
|
static int tvp5150_s_ctrl(struct v4l2_ctrl *ctrl)
|
|
{
|
|
struct v4l2_subdev *sd = to_sd(ctrl);
|
|
struct tvp5150 *decoder = to_tvp5150(sd);
|
|
|
|
switch (ctrl->id) {
|
|
case V4L2_CID_BRIGHTNESS:
|
|
regmap_write(decoder->regmap, TVP5150_BRIGHT_CTL, ctrl->val);
|
|
return 0;
|
|
case V4L2_CID_CONTRAST:
|
|
regmap_write(decoder->regmap, TVP5150_CONTRAST_CTL, ctrl->val);
|
|
return 0;
|
|
case V4L2_CID_SATURATION:
|
|
regmap_write(decoder->regmap, TVP5150_SATURATION_CTL,
|
|
ctrl->val);
|
|
return 0;
|
|
case V4L2_CID_HUE:
|
|
regmap_write(decoder->regmap, TVP5150_HUE_CTL, ctrl->val);
|
|
return 0;
|
|
case V4L2_CID_TEST_PATTERN:
|
|
decoder->enable = ctrl->val ? false : true;
|
|
tvp5150_selmux(sd);
|
|
return 0;
|
|
}
|
|
return -EINVAL;
|
|
}
|
|
|
|
static void tvp5150_set_default(v4l2_std_id std, struct v4l2_rect *crop)
|
|
{
|
|
/* Default is no cropping */
|
|
crop->top = 0;
|
|
crop->left = 0;
|
|
crop->width = TVP5150_H_MAX;
|
|
if (std & V4L2_STD_525_60)
|
|
crop->height = TVP5150_V_MAX_525_60;
|
|
else
|
|
crop->height = TVP5150_V_MAX_OTHERS;
|
|
}
|
|
|
|
static int tvp5150_fill_fmt(struct v4l2_subdev *sd,
|
|
struct v4l2_subdev_pad_config *cfg,
|
|
struct v4l2_subdev_format *format)
|
|
{
|
|
struct v4l2_mbus_framefmt *f;
|
|
struct tvp5150 *decoder = to_tvp5150(sd);
|
|
|
|
if (!format || (format->pad != TVP5150_PAD_VID_OUT))
|
|
return -EINVAL;
|
|
|
|
f = &format->format;
|
|
|
|
f->width = decoder->rect.width;
|
|
f->height = decoder->rect.height / 2;
|
|
|
|
f->code = TVP5150_MBUS_FMT;
|
|
f->field = TVP5150_FIELD;
|
|
f->colorspace = TVP5150_COLORSPACE;
|
|
|
|
dev_dbg_lvl(sd->dev, 1, debug, "width = %d, height = %d\n", f->width,
|
|
f->height);
|
|
return 0;
|
|
}
|
|
|
|
static int tvp5150_set_selection(struct v4l2_subdev *sd,
|
|
struct v4l2_subdev_pad_config *cfg,
|
|
struct v4l2_subdev_selection *sel)
|
|
{
|
|
struct tvp5150 *decoder = to_tvp5150(sd);
|
|
struct v4l2_rect rect = sel->r;
|
|
v4l2_std_id std;
|
|
int hmax;
|
|
|
|
if (sel->which != V4L2_SUBDEV_FORMAT_ACTIVE ||
|
|
sel->target != V4L2_SEL_TGT_CROP)
|
|
return -EINVAL;
|
|
|
|
dev_dbg_lvl(sd->dev, 1, debug, "%s left=%d, top=%d, width=%d, height=%d\n",
|
|
__func__, rect.left, rect.top, rect.width, rect.height);
|
|
|
|
/* tvp5150 has some special limits */
|
|
rect.left = clamp(rect.left, 0, TVP5150_MAX_CROP_LEFT);
|
|
rect.top = clamp(rect.top, 0, TVP5150_MAX_CROP_TOP);
|
|
|
|
/* Calculate height based on current standard */
|
|
if (decoder->norm == V4L2_STD_ALL)
|
|
std = tvp5150_read_std(sd);
|
|
else
|
|
std = decoder->norm;
|
|
|
|
if (std & V4L2_STD_525_60)
|
|
hmax = TVP5150_V_MAX_525_60;
|
|
else
|
|
hmax = TVP5150_V_MAX_OTHERS;
|
|
|
|
/*
|
|
* alignments:
|
|
* - width = 2 due to UYVY colorspace
|
|
* - height, image = no special alignment
|
|
*/
|
|
v4l_bound_align_image(&rect.width,
|
|
TVP5150_H_MAX - TVP5150_MAX_CROP_LEFT - rect.left,
|
|
TVP5150_H_MAX - rect.left, 1, &rect.height,
|
|
hmax - TVP5150_MAX_CROP_TOP - rect.top,
|
|
hmax - rect.top, 0, 0);
|
|
|
|
regmap_write(decoder->regmap, TVP5150_VERT_BLANKING_START, rect.top);
|
|
regmap_write(decoder->regmap, TVP5150_VERT_BLANKING_STOP,
|
|
rect.top + rect.height - hmax);
|
|
regmap_write(decoder->regmap, TVP5150_ACT_VD_CROP_ST_MSB,
|
|
rect.left >> TVP5150_CROP_SHIFT);
|
|
regmap_write(decoder->regmap, TVP5150_ACT_VD_CROP_ST_LSB,
|
|
rect.left | (1 << TVP5150_CROP_SHIFT));
|
|
regmap_write(decoder->regmap, TVP5150_ACT_VD_CROP_STP_MSB,
|
|
(rect.left + rect.width - TVP5150_MAX_CROP_LEFT) >>
|
|
TVP5150_CROP_SHIFT);
|
|
regmap_write(decoder->regmap, TVP5150_ACT_VD_CROP_STP_LSB,
|
|
rect.left + rect.width - TVP5150_MAX_CROP_LEFT);
|
|
|
|
decoder->rect = rect;
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int tvp5150_get_selection(struct v4l2_subdev *sd,
|
|
struct v4l2_subdev_pad_config *cfg,
|
|
struct v4l2_subdev_selection *sel)
|
|
{
|
|
struct tvp5150 *decoder = container_of(sd, struct tvp5150, sd);
|
|
v4l2_std_id std;
|
|
|
|
if (sel->which != V4L2_SUBDEV_FORMAT_ACTIVE)
|
|
return -EINVAL;
|
|
|
|
switch (sel->target) {
|
|
case V4L2_SEL_TGT_CROP_BOUNDS:
|
|
sel->r.left = 0;
|
|
sel->r.top = 0;
|
|
sel->r.width = TVP5150_H_MAX;
|
|
|
|
/* Calculate height based on current standard */
|
|
if (decoder->norm == V4L2_STD_ALL)
|
|
std = tvp5150_read_std(sd);
|
|
else
|
|
std = decoder->norm;
|
|
if (std & V4L2_STD_525_60)
|
|
sel->r.height = TVP5150_V_MAX_525_60;
|
|
else
|
|
sel->r.height = TVP5150_V_MAX_OTHERS;
|
|
return 0;
|
|
case V4L2_SEL_TGT_CROP:
|
|
sel->r = decoder->rect;
|
|
return 0;
|
|
default:
|
|
return -EINVAL;
|
|
}
|
|
}
|
|
|
|
static int tvp5150_g_mbus_config(struct v4l2_subdev *sd,
|
|
struct v4l2_mbus_config *cfg)
|
|
{
|
|
struct tvp5150 *decoder = to_tvp5150(sd);
|
|
|
|
cfg->type = decoder->mbus_type;
|
|
cfg->flags = V4L2_MBUS_MASTER | V4L2_MBUS_PCLK_SAMPLE_RISING
|
|
| V4L2_MBUS_FIELD_EVEN_LOW | V4L2_MBUS_DATA_ACTIVE_HIGH;
|
|
|
|
return 0;
|
|
}
|
|
|
|
/****************************************************************************
|
|
V4L2 subdev pad ops
|
|
****************************************************************************/
|
|
static int tvp5150_init_cfg(struct v4l2_subdev *sd,
|
|
struct v4l2_subdev_pad_config *cfg)
|
|
{
|
|
struct tvp5150 *decoder = to_tvp5150(sd);
|
|
v4l2_std_id std;
|
|
|
|
/*
|
|
* Reset selection to maximum on subdev_open() if autodetection is on
|
|
* and a standard change is detected.
|
|
*/
|
|
if (decoder->norm == V4L2_STD_ALL) {
|
|
std = tvp5150_read_std(sd);
|
|
if (std != decoder->detected_norm) {
|
|
decoder->detected_norm = std;
|
|
tvp5150_set_default(std, &decoder->rect);
|
|
}
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int tvp5150_enum_mbus_code(struct v4l2_subdev *sd,
|
|
struct v4l2_subdev_pad_config *cfg,
|
|
struct v4l2_subdev_mbus_code_enum *code)
|
|
{
|
|
if (code->pad || code->index)
|
|
return -EINVAL;
|
|
|
|
code->code = TVP5150_MBUS_FMT;
|
|
return 0;
|
|
}
|
|
|
|
static int tvp5150_enum_frame_size(struct v4l2_subdev *sd,
|
|
struct v4l2_subdev_pad_config *cfg,
|
|
struct v4l2_subdev_frame_size_enum *fse)
|
|
{
|
|
struct tvp5150 *decoder = to_tvp5150(sd);
|
|
|
|
if (fse->index >= 8 || fse->code != TVP5150_MBUS_FMT)
|
|
return -EINVAL;
|
|
|
|
fse->code = TVP5150_MBUS_FMT;
|
|
fse->min_width = decoder->rect.width;
|
|
fse->max_width = decoder->rect.width;
|
|
fse->min_height = decoder->rect.height / 2;
|
|
fse->max_height = decoder->rect.height / 2;
|
|
|
|
return 0;
|
|
}
|
|
|
|
/****************************************************************************
|
|
Media entity ops
|
|
****************************************************************************/
|
|
|
|
#ifdef CONFIG_MEDIA_CONTROLLER
|
|
static int tvp5150_link_setup(struct media_entity *entity,
|
|
const struct media_pad *local,
|
|
const struct media_pad *remote, u32 flags)
|
|
{
|
|
struct v4l2_subdev *sd = media_entity_to_v4l2_subdev(entity);
|
|
struct tvp5150 *decoder = to_tvp5150(sd);
|
|
int i;
|
|
|
|
for (i = 0; i < TVP5150_INPUT_NUM; i++) {
|
|
if (remote->entity == &decoder->input_ent[i])
|
|
break;
|
|
}
|
|
|
|
/* Do nothing for entities that are not input connectors */
|
|
if (i == TVP5150_INPUT_NUM)
|
|
return 0;
|
|
|
|
decoder->input = i;
|
|
|
|
tvp5150_selmux(sd);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static const struct media_entity_operations tvp5150_sd_media_ops = {
|
|
.link_setup = tvp5150_link_setup,
|
|
};
|
|
#endif
|
|
|
|
/****************************************************************************
|
|
I2C Command
|
|
****************************************************************************/
|
|
|
|
static int tvp5150_s_stream(struct v4l2_subdev *sd, int enable)
|
|
{
|
|
struct tvp5150 *decoder = to_tvp5150(sd);
|
|
unsigned int mask, val = 0, int_val = 0;
|
|
|
|
mask = TVP5150_MISC_CTL_YCBCR_OE | TVP5150_MISC_CTL_SYNC_OE |
|
|
TVP5150_MISC_CTL_CLOCK_OE;
|
|
|
|
if (enable) {
|
|
tvp5150_enable(sd);
|
|
|
|
/* Enable outputs if decoder is locked */
|
|
if (decoder->irq)
|
|
val = decoder->lock ? decoder->oe : 0;
|
|
else
|
|
val = decoder->oe;
|
|
int_val = TVP5150_INT_A_LOCK;
|
|
v4l2_subdev_notify_event(&decoder->sd, &tvp5150_ev_fmt);
|
|
}
|
|
|
|
regmap_update_bits(decoder->regmap, TVP5150_MISC_CTL, mask, val);
|
|
if (decoder->irq)
|
|
/* Enable / Disable lock interrupt */
|
|
regmap_update_bits(decoder->regmap, TVP5150_INT_ENABLE_REG_A,
|
|
TVP5150_INT_A_LOCK, int_val);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int tvp5150_s_routing(struct v4l2_subdev *sd,
|
|
u32 input, u32 output, u32 config)
|
|
{
|
|
struct tvp5150 *decoder = to_tvp5150(sd);
|
|
|
|
decoder->input = input;
|
|
decoder->output = output;
|
|
|
|
if (output == TVP5150_BLACK_SCREEN)
|
|
decoder->enable = false;
|
|
else
|
|
decoder->enable = true;
|
|
|
|
tvp5150_selmux(sd);
|
|
return 0;
|
|
}
|
|
|
|
static int tvp5150_s_raw_fmt(struct v4l2_subdev *sd, struct v4l2_vbi_format *fmt)
|
|
{
|
|
struct tvp5150 *decoder = to_tvp5150(sd);
|
|
|
|
/*
|
|
* this is for capturing 36 raw vbi lines
|
|
* if there's a way to cut off the beginning 2 vbi lines
|
|
* with the tvp5150 then the vbi line count could be lowered
|
|
* to 17 lines/field again, although I couldn't find a register
|
|
* which could do that cropping
|
|
*/
|
|
|
|
if (fmt->sample_format == V4L2_PIX_FMT_GREY)
|
|
regmap_write(decoder->regmap, TVP5150_LUMA_PROC_CTL_1, 0x70);
|
|
if (fmt->count[0] == 18 && fmt->count[1] == 18) {
|
|
regmap_write(decoder->regmap, TVP5150_VERT_BLANKING_START,
|
|
0x00);
|
|
regmap_write(decoder->regmap, TVP5150_VERT_BLANKING_STOP, 0x01);
|
|
}
|
|
return 0;
|
|
}
|
|
|
|
static int tvp5150_s_sliced_fmt(struct v4l2_subdev *sd, struct v4l2_sliced_vbi_format *svbi)
|
|
{
|
|
struct tvp5150 *decoder = to_tvp5150(sd);
|
|
int i;
|
|
|
|
if (svbi->service_set != 0) {
|
|
for (i = 0; i <= 23; i++) {
|
|
svbi->service_lines[1][i] = 0;
|
|
svbi->service_lines[0][i] =
|
|
tvp5150_set_vbi(sd, svbi->service_lines[0][i],
|
|
0xf0, i, 3);
|
|
}
|
|
/* Enables FIFO */
|
|
regmap_write(decoder->regmap, TVP5150_FIFO_OUT_CTRL, 1);
|
|
} else {
|
|
/* Disables FIFO*/
|
|
regmap_write(decoder->regmap, TVP5150_FIFO_OUT_CTRL, 0);
|
|
|
|
/* Disable Full Field */
|
|
regmap_write(decoder->regmap, TVP5150_FULL_FIELD_ENA, 0);
|
|
|
|
/* Disable Line modes */
|
|
for (i = TVP5150_LINE_MODE_INI; i <= TVP5150_LINE_MODE_END; i++)
|
|
regmap_write(decoder->regmap, i, 0xff);
|
|
}
|
|
return 0;
|
|
}
|
|
|
|
static int tvp5150_g_sliced_fmt(struct v4l2_subdev *sd, struct v4l2_sliced_vbi_format *svbi)
|
|
{
|
|
int i, mask = 0;
|
|
|
|
memset(svbi->service_lines, 0, sizeof(svbi->service_lines));
|
|
|
|
for (i = 0; i <= 23; i++) {
|
|
svbi->service_lines[0][i] =
|
|
tvp5150_get_vbi(sd, i);
|
|
mask |= svbi->service_lines[0][i];
|
|
}
|
|
svbi->service_set = mask;
|
|
return 0;
|
|
}
|
|
|
|
#ifdef CONFIG_VIDEO_ADV_DEBUG
|
|
static int tvp5150_g_register(struct v4l2_subdev *sd, struct v4l2_dbg_register *reg)
|
|
{
|
|
int res;
|
|
|
|
res = tvp5150_read(sd, reg->reg & 0xff);
|
|
if (res < 0) {
|
|
dev_err(sd->dev, "%s: failed with error = %d\n", __func__, res);
|
|
return res;
|
|
}
|
|
|
|
reg->val = res;
|
|
reg->size = 1;
|
|
return 0;
|
|
}
|
|
|
|
static int tvp5150_s_register(struct v4l2_subdev *sd, const struct v4l2_dbg_register *reg)
|
|
{
|
|
struct tvp5150 *decoder = to_tvp5150(sd);
|
|
|
|
return regmap_write(decoder->regmap, reg->reg & 0xff, reg->val & 0xff);
|
|
}
|
|
#endif
|
|
|
|
static int tvp5150_g_tuner(struct v4l2_subdev *sd, struct v4l2_tuner *vt)
|
|
{
|
|
int status = tvp5150_read(sd, 0x88);
|
|
|
|
vt->signal = ((status & 0x04) && (status & 0x02)) ? 0xffff : 0x0;
|
|
return 0;
|
|
}
|
|
|
|
static int tvp5150_registered(struct v4l2_subdev *sd)
|
|
{
|
|
#ifdef CONFIG_MEDIA_CONTROLLER
|
|
struct tvp5150 *decoder = to_tvp5150(sd);
|
|
int ret = 0;
|
|
int i;
|
|
|
|
for (i = 0; i < TVP5150_INPUT_NUM; i++) {
|
|
struct media_entity *input = &decoder->input_ent[i];
|
|
struct media_pad *pad = &decoder->input_pad[i];
|
|
|
|
if (!input->name)
|
|
continue;
|
|
|
|
decoder->input_pad[i].flags = MEDIA_PAD_FL_SOURCE;
|
|
|
|
ret = media_entity_pads_init(input, 1, pad);
|
|
if (ret < 0)
|
|
return ret;
|
|
|
|
ret = media_device_register_entity(sd->v4l2_dev->mdev, input);
|
|
if (ret < 0)
|
|
return ret;
|
|
|
|
ret = media_create_pad_link(input, 0, &sd->entity,
|
|
TVP5150_PAD_IF_INPUT, 0);
|
|
if (ret < 0) {
|
|
media_device_unregister_entity(input);
|
|
return ret;
|
|
}
|
|
}
|
|
#endif
|
|
|
|
return 0;
|
|
}
|
|
|
|
/* ----------------------------------------------------------------------- */
|
|
|
|
static const struct v4l2_ctrl_ops tvp5150_ctrl_ops = {
|
|
.s_ctrl = tvp5150_s_ctrl,
|
|
};
|
|
|
|
static const struct v4l2_subdev_core_ops tvp5150_core_ops = {
|
|
.log_status = tvp5150_log_status,
|
|
.reset = tvp5150_reset,
|
|
#ifdef CONFIG_VIDEO_ADV_DEBUG
|
|
.g_register = tvp5150_g_register,
|
|
.s_register = tvp5150_s_register,
|
|
#endif
|
|
};
|
|
|
|
static const struct v4l2_subdev_tuner_ops tvp5150_tuner_ops = {
|
|
.g_tuner = tvp5150_g_tuner,
|
|
};
|
|
|
|
static const struct v4l2_subdev_video_ops tvp5150_video_ops = {
|
|
.s_std = tvp5150_s_std,
|
|
.g_std = tvp5150_g_std,
|
|
.querystd = tvp5150_querystd,
|
|
.s_stream = tvp5150_s_stream,
|
|
.s_routing = tvp5150_s_routing,
|
|
.g_mbus_config = tvp5150_g_mbus_config,
|
|
};
|
|
|
|
static const struct v4l2_subdev_vbi_ops tvp5150_vbi_ops = {
|
|
.g_sliced_vbi_cap = tvp5150_g_sliced_vbi_cap,
|
|
.g_sliced_fmt = tvp5150_g_sliced_fmt,
|
|
.s_sliced_fmt = tvp5150_s_sliced_fmt,
|
|
.s_raw_fmt = tvp5150_s_raw_fmt,
|
|
};
|
|
|
|
static const struct v4l2_subdev_pad_ops tvp5150_pad_ops = {
|
|
.init_cfg = tvp5150_init_cfg,
|
|
.enum_mbus_code = tvp5150_enum_mbus_code,
|
|
.enum_frame_size = tvp5150_enum_frame_size,
|
|
.set_fmt = tvp5150_fill_fmt,
|
|
.get_fmt = tvp5150_fill_fmt,
|
|
.get_selection = tvp5150_get_selection,
|
|
.set_selection = tvp5150_set_selection,
|
|
};
|
|
|
|
static const struct v4l2_subdev_ops tvp5150_ops = {
|
|
.core = &tvp5150_core_ops,
|
|
.tuner = &tvp5150_tuner_ops,
|
|
.video = &tvp5150_video_ops,
|
|
.vbi = &tvp5150_vbi_ops,
|
|
.pad = &tvp5150_pad_ops,
|
|
};
|
|
|
|
static const struct v4l2_subdev_internal_ops tvp5150_internal_ops = {
|
|
.registered = tvp5150_registered,
|
|
};
|
|
|
|
/****************************************************************************
|
|
I2C Client & Driver
|
|
****************************************************************************/
|
|
|
|
static const struct regmap_range tvp5150_readable_ranges[] = {
|
|
{
|
|
.range_min = TVP5150_VD_IN_SRC_SEL_1,
|
|
.range_max = TVP5150_AUTOSW_MSK,
|
|
}, {
|
|
.range_min = TVP5150_COLOR_KIL_THSH_CTL,
|
|
.range_max = TVP5150_CONF_SHARED_PIN,
|
|
}, {
|
|
.range_min = TVP5150_ACT_VD_CROP_ST_MSB,
|
|
.range_max = TVP5150_HORIZ_SYNC_START,
|
|
}, {
|
|
.range_min = TVP5150_VERT_BLANKING_START,
|
|
.range_max = TVP5150_INTT_CONFIG_REG_B,
|
|
}, {
|
|
.range_min = TVP5150_VIDEO_STD,
|
|
.range_max = TVP5150_VIDEO_STD,
|
|
}, {
|
|
.range_min = TVP5150_CB_GAIN_FACT,
|
|
.range_max = TVP5150_REV_SELECT,
|
|
}, {
|
|
.range_min = TVP5150_MSB_DEV_ID,
|
|
.range_max = TVP5150_STATUS_REG_5,
|
|
}, {
|
|
.range_min = TVP5150_CC_DATA_INI,
|
|
.range_max = TVP5150_TELETEXT_FIL_ENA,
|
|
}, {
|
|
.range_min = TVP5150_INT_STATUS_REG_A,
|
|
.range_max = TVP5150_FIFO_OUT_CTRL,
|
|
}, {
|
|
.range_min = TVP5150_FULL_FIELD_ENA,
|
|
.range_max = TVP5150_FULL_FIELD_MODE_REG,
|
|
},
|
|
};
|
|
|
|
static bool tvp5150_volatile_reg(struct device *dev, unsigned int reg)
|
|
{
|
|
switch (reg) {
|
|
case TVP5150_VERT_LN_COUNT_MSB:
|
|
case TVP5150_VERT_LN_COUNT_LSB:
|
|
case TVP5150_INT_STATUS_REG_A:
|
|
case TVP5150_INT_STATUS_REG_B:
|
|
case TVP5150_INT_ACTIVE_REG_B:
|
|
case TVP5150_STATUS_REG_1:
|
|
case TVP5150_STATUS_REG_2:
|
|
case TVP5150_STATUS_REG_3:
|
|
case TVP5150_STATUS_REG_4:
|
|
case TVP5150_STATUS_REG_5:
|
|
/* CC, WSS, VPS, VITC data? */
|
|
case TVP5150_VBI_FIFO_READ_DATA:
|
|
case TVP5150_VDP_STATUS_REG:
|
|
case TVP5150_FIFO_WORD_COUNT:
|
|
return true;
|
|
default:
|
|
return false;
|
|
}
|
|
}
|
|
|
|
static const struct regmap_access_table tvp5150_readable_table = {
|
|
.yes_ranges = tvp5150_readable_ranges,
|
|
.n_yes_ranges = ARRAY_SIZE(tvp5150_readable_ranges),
|
|
};
|
|
|
|
static struct regmap_config tvp5150_config = {
|
|
.reg_bits = 8,
|
|
.val_bits = 8,
|
|
.max_register = 0xff,
|
|
|
|
.cache_type = REGCACHE_RBTREE,
|
|
|
|
.rd_table = &tvp5150_readable_table,
|
|
.volatile_reg = tvp5150_volatile_reg,
|
|
};
|
|
|
|
static int tvp5150_detect_version(struct tvp5150 *core)
|
|
{
|
|
struct v4l2_subdev *sd = &core->sd;
|
|
struct i2c_client *c = v4l2_get_subdevdata(sd);
|
|
u8 regs[4];
|
|
int res;
|
|
|
|
/*
|
|
* Read consequent registers - TVP5150_MSB_DEV_ID, TVP5150_LSB_DEV_ID,
|
|
* TVP5150_ROM_MAJOR_VER, TVP5150_ROM_MINOR_VER
|
|
*/
|
|
res = regmap_bulk_read(core->regmap, TVP5150_MSB_DEV_ID, regs, 4);
|
|
if (res < 0) {
|
|
dev_err(&c->dev, "reading ID registers failed: %d\n", res);
|
|
return res;
|
|
}
|
|
|
|
core->dev_id = (regs[0] << 8) | regs[1];
|
|
core->rom_ver = (regs[2] << 8) | regs[3];
|
|
|
|
dev_info(sd->dev, "tvp%04x (%u.%u) chip found @ 0x%02x (%s)\n",
|
|
core->dev_id, regs[2], regs[3], c->addr << 1,
|
|
c->adapter->name);
|
|
|
|
if (core->dev_id == 0x5150 && core->rom_ver == 0x0321) {
|
|
dev_info(sd->dev, "tvp5150a detected.\n");
|
|
} else if (core->dev_id == 0x5150 && core->rom_ver == 0x0400) {
|
|
dev_info(sd->dev, "tvp5150am1 detected.\n");
|
|
|
|
/* ITU-T BT.656.4 timing */
|
|
regmap_write(core->regmap, TVP5150_REV_SELECT, 0);
|
|
} else if (core->dev_id == 0x5151 && core->rom_ver == 0x0100) {
|
|
dev_info(sd->dev, "tvp5151 detected.\n");
|
|
} else {
|
|
dev_info(sd->dev, "*** unknown tvp%04x chip detected.\n",
|
|
core->dev_id);
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int tvp5150_init(struct i2c_client *c)
|
|
{
|
|
struct gpio_desc *pdn_gpio;
|
|
struct gpio_desc *reset_gpio;
|
|
|
|
pdn_gpio = devm_gpiod_get_optional(&c->dev, "pdn", GPIOD_OUT_HIGH);
|
|
if (IS_ERR(pdn_gpio))
|
|
return PTR_ERR(pdn_gpio);
|
|
|
|
if (pdn_gpio) {
|
|
gpiod_set_value_cansleep(pdn_gpio, 0);
|
|
/* Delay time between power supplies active and reset */
|
|
msleep(20);
|
|
}
|
|
|
|
reset_gpio = devm_gpiod_get_optional(&c->dev, "reset", GPIOD_OUT_HIGH);
|
|
if (IS_ERR(reset_gpio))
|
|
return PTR_ERR(reset_gpio);
|
|
|
|
if (reset_gpio) {
|
|
/* RESETB pulse duration */
|
|
ndelay(500);
|
|
gpiod_set_value_cansleep(reset_gpio, 0);
|
|
/* Delay time between end of reset to I2C active */
|
|
usleep_range(200, 250);
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int tvp5150_parse_dt(struct tvp5150 *decoder, struct device_node *np)
|
|
{
|
|
struct v4l2_fwnode_endpoint bus_cfg = { .bus_type = 0 };
|
|
struct device_node *ep;
|
|
#ifdef CONFIG_MEDIA_CONTROLLER
|
|
struct device_node *connectors, *child;
|
|
struct media_entity *input;
|
|
const char *name;
|
|
u32 input_type;
|
|
#endif
|
|
unsigned int flags;
|
|
int ret = 0;
|
|
|
|
ep = of_graph_get_next_endpoint(np, NULL);
|
|
if (!ep)
|
|
return -EINVAL;
|
|
|
|
ret = v4l2_fwnode_endpoint_parse(of_fwnode_handle(ep), &bus_cfg);
|
|
if (ret)
|
|
goto err;
|
|
|
|
flags = bus_cfg.bus.parallel.flags;
|
|
|
|
if (bus_cfg.bus_type == V4L2_MBUS_PARALLEL &&
|
|
!(flags & V4L2_MBUS_HSYNC_ACTIVE_HIGH &&
|
|
flags & V4L2_MBUS_VSYNC_ACTIVE_HIGH &&
|
|
flags & V4L2_MBUS_FIELD_EVEN_LOW)) {
|
|
ret = -EINVAL;
|
|
goto err;
|
|
}
|
|
|
|
decoder->mbus_type = bus_cfg.bus_type;
|
|
|
|
#ifdef CONFIG_MEDIA_CONTROLLER
|
|
connectors = of_get_child_by_name(np, "connectors");
|
|
|
|
if (!connectors)
|
|
goto err;
|
|
|
|
for_each_available_child_of_node(connectors, child) {
|
|
ret = of_property_read_u32(child, "input", &input_type);
|
|
if (ret) {
|
|
dev_err(decoder->sd.dev,
|
|
"missing type property in node %pOFn\n",
|
|
child);
|
|
goto err_connector;
|
|
}
|
|
|
|
if (input_type >= TVP5150_INPUT_NUM) {
|
|
ret = -EINVAL;
|
|
goto err_connector;
|
|
}
|
|
|
|
input = &decoder->input_ent[input_type];
|
|
|
|
/* Each input connector can only be defined once */
|
|
if (input->name) {
|
|
dev_err(decoder->sd.dev,
|
|
"input %s with same type already exists\n",
|
|
input->name);
|
|
ret = -EINVAL;
|
|
goto err_connector;
|
|
}
|
|
|
|
switch (input_type) {
|
|
case TVP5150_COMPOSITE0:
|
|
case TVP5150_COMPOSITE1:
|
|
input->function = MEDIA_ENT_F_CONN_COMPOSITE;
|
|
break;
|
|
case TVP5150_SVIDEO:
|
|
input->function = MEDIA_ENT_F_CONN_SVIDEO;
|
|
break;
|
|
}
|
|
|
|
input->flags = MEDIA_ENT_FL_CONNECTOR;
|
|
|
|
ret = of_property_read_string(child, "label", &name);
|
|
if (ret < 0) {
|
|
dev_err(decoder->sd.dev,
|
|
"missing label property in node %pOFn\n",
|
|
child);
|
|
goto err_connector;
|
|
}
|
|
|
|
input->name = name;
|
|
}
|
|
|
|
err_connector:
|
|
of_node_put(connectors);
|
|
#endif
|
|
err:
|
|
of_node_put(ep);
|
|
return ret;
|
|
}
|
|
|
|
static const char * const tvp5150_test_patterns[2] = {
|
|
"Disabled",
|
|
"Black screen"
|
|
};
|
|
|
|
static int tvp5150_probe(struct i2c_client *c,
|
|
const struct i2c_device_id *id)
|
|
{
|
|
struct tvp5150 *core;
|
|
struct v4l2_subdev *sd;
|
|
struct device_node *np = c->dev.of_node;
|
|
struct regmap *map;
|
|
int res;
|
|
|
|
/* Check if the adapter supports the needed features */
|
|
if (!i2c_check_functionality(c->adapter,
|
|
I2C_FUNC_SMBUS_READ_BYTE | I2C_FUNC_SMBUS_WRITE_BYTE_DATA))
|
|
return -EIO;
|
|
|
|
res = tvp5150_init(c);
|
|
if (res)
|
|
return res;
|
|
|
|
core = devm_kzalloc(&c->dev, sizeof(*core), GFP_KERNEL);
|
|
if (!core)
|
|
return -ENOMEM;
|
|
|
|
map = devm_regmap_init_i2c(c, &tvp5150_config);
|
|
if (IS_ERR(map))
|
|
return PTR_ERR(map);
|
|
|
|
core->regmap = map;
|
|
sd = &core->sd;
|
|
|
|
if (IS_ENABLED(CONFIG_OF) && np) {
|
|
res = tvp5150_parse_dt(core, np);
|
|
if (res) {
|
|
dev_err(sd->dev, "DT parsing error: %d\n", res);
|
|
return res;
|
|
}
|
|
} else {
|
|
/* Default to BT.656 embedded sync */
|
|
core->mbus_type = V4L2_MBUS_BT656;
|
|
}
|
|
|
|
v4l2_i2c_subdev_init(sd, c, &tvp5150_ops);
|
|
sd->internal_ops = &tvp5150_internal_ops;
|
|
sd->flags |= V4L2_SUBDEV_FL_HAS_DEVNODE;
|
|
|
|
#if defined(CONFIG_MEDIA_CONTROLLER)
|
|
core->pads[TVP5150_PAD_IF_INPUT].flags = MEDIA_PAD_FL_SINK;
|
|
core->pads[TVP5150_PAD_IF_INPUT].sig_type = PAD_SIGNAL_ANALOG;
|
|
core->pads[TVP5150_PAD_VID_OUT].flags = MEDIA_PAD_FL_SOURCE;
|
|
core->pads[TVP5150_PAD_VID_OUT].sig_type = PAD_SIGNAL_DV;
|
|
|
|
sd->entity.function = MEDIA_ENT_F_ATV_DECODER;
|
|
|
|
res = media_entity_pads_init(&sd->entity, TVP5150_NUM_PADS, core->pads);
|
|
if (res < 0)
|
|
return res;
|
|
|
|
sd->entity.ops = &tvp5150_sd_media_ops;
|
|
#endif
|
|
|
|
res = tvp5150_detect_version(core);
|
|
if (res < 0)
|
|
return res;
|
|
|
|
core->norm = V4L2_STD_ALL; /* Default is autodetect */
|
|
core->detected_norm = V4L2_STD_UNKNOWN;
|
|
core->input = TVP5150_COMPOSITE1;
|
|
core->enable = true;
|
|
|
|
v4l2_ctrl_handler_init(&core->hdl, 5);
|
|
v4l2_ctrl_new_std(&core->hdl, &tvp5150_ctrl_ops,
|
|
V4L2_CID_BRIGHTNESS, 0, 255, 1, 128);
|
|
v4l2_ctrl_new_std(&core->hdl, &tvp5150_ctrl_ops,
|
|
V4L2_CID_CONTRAST, 0, 255, 1, 128);
|
|
v4l2_ctrl_new_std(&core->hdl, &tvp5150_ctrl_ops,
|
|
V4L2_CID_SATURATION, 0, 255, 1, 128);
|
|
v4l2_ctrl_new_std(&core->hdl, &tvp5150_ctrl_ops,
|
|
V4L2_CID_HUE, -128, 127, 1, 0);
|
|
v4l2_ctrl_new_std(&core->hdl, &tvp5150_ctrl_ops,
|
|
V4L2_CID_PIXEL_RATE, 27000000,
|
|
27000000, 1, 27000000);
|
|
v4l2_ctrl_new_std_menu_items(&core->hdl, &tvp5150_ctrl_ops,
|
|
V4L2_CID_TEST_PATTERN,
|
|
ARRAY_SIZE(tvp5150_test_patterns) - 1,
|
|
0, 0, tvp5150_test_patterns);
|
|
sd->ctrl_handler = &core->hdl;
|
|
if (core->hdl.error) {
|
|
res = core->hdl.error;
|
|
goto err;
|
|
}
|
|
|
|
tvp5150_set_default(tvp5150_read_std(sd), &core->rect);
|
|
|
|
core->irq = c->irq;
|
|
tvp5150_reset(sd, 0); /* Calls v4l2_ctrl_handler_setup() */
|
|
if (c->irq) {
|
|
res = devm_request_threaded_irq(&c->dev, c->irq, NULL,
|
|
tvp5150_isr, IRQF_TRIGGER_HIGH |
|
|
IRQF_ONESHOT, "tvp5150", core);
|
|
if (res)
|
|
return res;
|
|
}
|
|
|
|
res = v4l2_async_register_subdev(sd);
|
|
if (res < 0)
|
|
goto err;
|
|
|
|
if (debug > 1)
|
|
tvp5150_log_status(sd);
|
|
return 0;
|
|
|
|
err:
|
|
v4l2_ctrl_handler_free(&core->hdl);
|
|
return res;
|
|
}
|
|
|
|
static int tvp5150_remove(struct i2c_client *c)
|
|
{
|
|
struct v4l2_subdev *sd = i2c_get_clientdata(c);
|
|
struct tvp5150 *decoder = to_tvp5150(sd);
|
|
|
|
dev_dbg_lvl(sd->dev, 1, debug,
|
|
"tvp5150.c: removing tvp5150 adapter on address 0x%x\n",
|
|
c->addr << 1);
|
|
|
|
v4l2_async_unregister_subdev(sd);
|
|
v4l2_ctrl_handler_free(&decoder->hdl);
|
|
return 0;
|
|
}
|
|
|
|
/* ----------------------------------------------------------------------- */
|
|
|
|
static const struct i2c_device_id tvp5150_id[] = {
|
|
{ "tvp5150", 0 },
|
|
{ }
|
|
};
|
|
MODULE_DEVICE_TABLE(i2c, tvp5150_id);
|
|
|
|
#if IS_ENABLED(CONFIG_OF)
|
|
static const struct of_device_id tvp5150_of_match[] = {
|
|
{ .compatible = "ti,tvp5150", },
|
|
{ /* sentinel */ },
|
|
};
|
|
MODULE_DEVICE_TABLE(of, tvp5150_of_match);
|
|
#endif
|
|
|
|
static struct i2c_driver tvp5150_driver = {
|
|
.driver = {
|
|
.of_match_table = of_match_ptr(tvp5150_of_match),
|
|
.name = "tvp5150",
|
|
},
|
|
.probe = tvp5150_probe,
|
|
.remove = tvp5150_remove,
|
|
.id_table = tvp5150_id,
|
|
};
|
|
|
|
module_i2c_driver(tvp5150_driver);
|