347 lines
9.1 KiB
C
347 lines
9.1 KiB
C
/*
|
|
* Copyright (C) 2000-2002 Mark Lord <mlord@pobox.com>
|
|
* Copyright (C) 2007 Bartlomiej Zolnierkiewicz
|
|
*
|
|
* May be copied or modified under the terms of the GNU General Public License
|
|
*
|
|
* Development of this chipset driver was funded
|
|
* by the nice folks at National Semiconductor.
|
|
*
|
|
* Documentation:
|
|
* Available from National Semiconductor
|
|
*/
|
|
|
|
#include <linux/module.h>
|
|
#include <linux/types.h>
|
|
#include <linux/kernel.h>
|
|
#include <linux/hdreg.h>
|
|
#include <linux/pci.h>
|
|
#include <linux/init.h>
|
|
#include <linux/ide.h>
|
|
#include <linux/pm.h>
|
|
|
|
#include <asm/io.h>
|
|
|
|
#define SC1200_REV_A 0x00
|
|
#define SC1200_REV_B1 0x01
|
|
#define SC1200_REV_B3 0x02
|
|
#define SC1200_REV_C1 0x03
|
|
#define SC1200_REV_D1 0x04
|
|
|
|
#define PCI_CLK_33 0x00
|
|
#define PCI_CLK_48 0x01
|
|
#define PCI_CLK_66 0x02
|
|
#define PCI_CLK_33A 0x03
|
|
|
|
static unsigned short sc1200_get_pci_clock (void)
|
|
{
|
|
unsigned char chip_id, silicon_revision;
|
|
unsigned int pci_clock;
|
|
/*
|
|
* Check the silicon revision, as not all versions of the chip
|
|
* have the register with the fast PCI bus timings.
|
|
*/
|
|
chip_id = inb (0x903c);
|
|
silicon_revision = inb (0x903d);
|
|
|
|
// Read the fast pci clock frequency
|
|
if (chip_id == 0x04 && silicon_revision < SC1200_REV_B1) {
|
|
pci_clock = PCI_CLK_33;
|
|
} else {
|
|
// check clock generator configuration (cfcc)
|
|
// the clock is in bits 8 and 9 of this word
|
|
|
|
pci_clock = inw (0x901e);
|
|
pci_clock >>= 8;
|
|
pci_clock &= 0x03;
|
|
if (pci_clock == PCI_CLK_33A)
|
|
pci_clock = PCI_CLK_33;
|
|
}
|
|
return pci_clock;
|
|
}
|
|
|
|
/*
|
|
* Here are the standard PIO mode 0-4 timings for each "format".
|
|
* Format-0 uses fast data reg timings, with slower command reg timings.
|
|
* Format-1 uses fast timings for all registers, but won't work with all drives.
|
|
*/
|
|
static const unsigned int sc1200_pio_timings[4][5] =
|
|
{{0x00009172, 0x00012171, 0x00020080, 0x00032010, 0x00040010}, // format0 33Mhz
|
|
{0xd1329172, 0x71212171, 0x30200080, 0x20102010, 0x00100010}, // format1, 33Mhz
|
|
{0xfaa3f4f3, 0xc23232b2, 0x513101c1, 0x31213121, 0x10211021}, // format1, 48Mhz
|
|
{0xfff4fff4, 0xf35353d3, 0x814102f1, 0x42314231, 0x11311131}}; // format1, 66Mhz
|
|
|
|
/*
|
|
* After chip reset, the PIO timings are set to 0x00009172, which is not valid.
|
|
*/
|
|
//#define SC1200_BAD_PIO(timings) (((timings)&~0x80000000)==0x00009172)
|
|
|
|
static void sc1200_tunepio(ide_drive_t *drive, u8 pio)
|
|
{
|
|
ide_hwif_t *hwif = drive->hwif;
|
|
struct pci_dev *pdev = to_pci_dev(hwif->dev);
|
|
unsigned int basereg = hwif->channel ? 0x50 : 0x40, format = 0;
|
|
|
|
pci_read_config_dword(pdev, basereg + 4, &format);
|
|
format = (format >> 31) & 1;
|
|
if (format)
|
|
format += sc1200_get_pci_clock();
|
|
pci_write_config_dword(pdev, basereg + ((drive->dn & 1) << 3),
|
|
sc1200_pio_timings[format][pio]);
|
|
}
|
|
|
|
/*
|
|
* The SC1200 specifies that two drives sharing a cable cannot mix
|
|
* UDMA/MDMA. It has to be one or the other, for the pair, though
|
|
* different timings can still be chosen for each drive. We could
|
|
* set the appropriate timing bits on the fly, but that might be
|
|
* a bit confusing. So, for now we statically handle this requirement
|
|
* by looking at our mate drive to see what it is capable of, before
|
|
* choosing a mode for our own drive.
|
|
*/
|
|
static u8 sc1200_udma_filter(ide_drive_t *drive)
|
|
{
|
|
ide_hwif_t *hwif = drive->hwif;
|
|
ide_drive_t *mate = &hwif->drives[(drive->dn & 1) ^ 1];
|
|
struct hd_driveid *mateid = mate->id;
|
|
u8 mask = hwif->ultra_mask;
|
|
|
|
if (mate->present == 0)
|
|
goto out;
|
|
|
|
if ((mateid->capability & 1) && __ide_dma_bad_drive(mate) == 0) {
|
|
if ((mateid->field_valid & 4) && (mateid->dma_ultra & 7))
|
|
goto out;
|
|
if ((mateid->field_valid & 2) && (mateid->dma_mword & 7))
|
|
mask = 0;
|
|
}
|
|
out:
|
|
return mask;
|
|
}
|
|
|
|
static void sc1200_set_dma_mode(ide_drive_t *drive, const u8 mode)
|
|
{
|
|
ide_hwif_t *hwif = HWIF(drive);
|
|
struct pci_dev *dev = to_pci_dev(hwif->dev);
|
|
int unit = drive->select.b.unit;
|
|
unsigned int reg, timings;
|
|
unsigned short pci_clock;
|
|
unsigned int basereg = hwif->channel ? 0x50 : 0x40;
|
|
|
|
static const u32 udma_timing[3][3] = {
|
|
{ 0x00921250, 0x00911140, 0x00911030 },
|
|
{ 0x00932470, 0x00922260, 0x00922140 },
|
|
{ 0x009436a1, 0x00933481, 0x00923261 },
|
|
};
|
|
|
|
static const u32 mwdma_timing[3][3] = {
|
|
{ 0x00077771, 0x00012121, 0x00002020 },
|
|
{ 0x000bbbb2, 0x00024241, 0x00013131 },
|
|
{ 0x000ffff3, 0x00035352, 0x00015151 },
|
|
};
|
|
|
|
pci_clock = sc1200_get_pci_clock();
|
|
|
|
/*
|
|
* Note that each DMA mode has several timings associated with it.
|
|
* The correct timing depends on the fast PCI clock freq.
|
|
*/
|
|
|
|
if (mode >= XFER_UDMA_0)
|
|
timings = udma_timing[pci_clock][mode - XFER_UDMA_0];
|
|
else
|
|
timings = mwdma_timing[pci_clock][mode - XFER_MW_DMA_0];
|
|
|
|
if (unit == 0) { /* are we configuring drive0? */
|
|
pci_read_config_dword(dev, basereg + 4, ®);
|
|
timings |= reg & 0x80000000; /* preserve PIO format bit */
|
|
pci_write_config_dword(dev, basereg + 4, timings);
|
|
} else
|
|
pci_write_config_dword(dev, basereg + 12, timings);
|
|
}
|
|
|
|
/* Replacement for the standard ide_dma_end action in
|
|
* dma_proc.
|
|
*
|
|
* returns 1 on error, 0 otherwise
|
|
*/
|
|
static int sc1200_ide_dma_end (ide_drive_t *drive)
|
|
{
|
|
ide_hwif_t *hwif = HWIF(drive);
|
|
unsigned long dma_base = hwif->dma_base;
|
|
byte dma_stat;
|
|
|
|
dma_stat = inb(dma_base+2); /* get DMA status */
|
|
|
|
if (!(dma_stat & 4))
|
|
printk(" ide_dma_end dma_stat=%0x err=%x newerr=%x\n",
|
|
dma_stat, ((dma_stat&7)!=4), ((dma_stat&2)==2));
|
|
|
|
outb(dma_stat|0x1b, dma_base+2); /* clear the INTR & ERROR bits */
|
|
outb(inb(dma_base)&~1, dma_base); /* !! DO THIS HERE !! stop DMA */
|
|
|
|
drive->waiting_for_dma = 0;
|
|
ide_destroy_dmatable(drive); /* purge DMA mappings */
|
|
|
|
return (dma_stat & 7) != 4; /* verify good DMA status */
|
|
}
|
|
|
|
/*
|
|
* sc1200_set_pio_mode() handles setting of PIO modes
|
|
* for both the chipset and drive.
|
|
*
|
|
* All existing BIOSs for this chipset guarantee that all drives
|
|
* will have valid default PIO timings set up before we get here.
|
|
*/
|
|
|
|
static void sc1200_set_pio_mode(ide_drive_t *drive, const u8 pio)
|
|
{
|
|
ide_hwif_t *hwif = HWIF(drive);
|
|
int mode = -1;
|
|
|
|
/*
|
|
* bad abuse of ->set_pio_mode interface
|
|
*/
|
|
switch (pio) {
|
|
case 200: mode = XFER_UDMA_0; break;
|
|
case 201: mode = XFER_UDMA_1; break;
|
|
case 202: mode = XFER_UDMA_2; break;
|
|
case 100: mode = XFER_MW_DMA_0; break;
|
|
case 101: mode = XFER_MW_DMA_1; break;
|
|
case 102: mode = XFER_MW_DMA_2; break;
|
|
}
|
|
if (mode != -1) {
|
|
printk("SC1200: %s: changing (U)DMA mode\n", drive->name);
|
|
ide_dma_off_quietly(drive);
|
|
if (ide_set_dma_mode(drive, mode) == 0 && drive->using_dma)
|
|
hwif->dma_host_set(drive, 1);
|
|
return;
|
|
}
|
|
|
|
sc1200_tunepio(drive, pio);
|
|
}
|
|
|
|
#ifdef CONFIG_PM
|
|
struct sc1200_saved_state {
|
|
u32 regs[8];
|
|
};
|
|
|
|
static int sc1200_suspend (struct pci_dev *dev, pm_message_t state)
|
|
{
|
|
printk("SC1200: suspend(%u)\n", state.event);
|
|
|
|
/*
|
|
* we only save state when going from full power to less
|
|
*/
|
|
if (state.event == PM_EVENT_ON) {
|
|
struct sc1200_saved_state *ss;
|
|
unsigned int r;
|
|
|
|
/*
|
|
* allocate a permanent save area, if not already allocated
|
|
*/
|
|
ss = (struct sc1200_saved_state *)pci_get_drvdata(dev);
|
|
if (ss == NULL) {
|
|
ss = kmalloc(sizeof(*ss), GFP_KERNEL);
|
|
if (ss == NULL)
|
|
return -ENOMEM;
|
|
pci_set_drvdata(dev, ss);
|
|
}
|
|
|
|
/*
|
|
* save timing registers
|
|
* (this may be unnecessary if BIOS also does it)
|
|
*/
|
|
for (r = 0; r < 8; r++)
|
|
pci_read_config_dword(dev, 0x40 + r * 4, &ss->regs[r]);
|
|
}
|
|
|
|
pci_disable_device(dev);
|
|
pci_set_power_state(dev, pci_choose_state(dev, state));
|
|
return 0;
|
|
}
|
|
|
|
static int sc1200_resume (struct pci_dev *dev)
|
|
{
|
|
struct sc1200_saved_state *ss;
|
|
unsigned int r;
|
|
int i;
|
|
|
|
i = pci_enable_device(dev);
|
|
if (i)
|
|
return i;
|
|
|
|
ss = (struct sc1200_saved_state *)pci_get_drvdata(dev);
|
|
|
|
/*
|
|
* restore timing registers
|
|
* (this may be unnecessary if BIOS also does it)
|
|
*/
|
|
if (ss) {
|
|
for (r = 0; r < 8; r++)
|
|
pci_write_config_dword(dev, 0x40 + r * 4, ss->regs[r]);
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
#endif
|
|
|
|
/*
|
|
* This gets invoked by the IDE driver once for each channel,
|
|
* and performs channel-specific pre-initialization before drive probing.
|
|
*/
|
|
static void __devinit init_hwif_sc1200 (ide_hwif_t *hwif)
|
|
{
|
|
hwif->set_pio_mode = &sc1200_set_pio_mode;
|
|
hwif->set_dma_mode = &sc1200_set_dma_mode;
|
|
|
|
if (hwif->dma_base == 0)
|
|
return;
|
|
|
|
hwif->udma_filter = sc1200_udma_filter;
|
|
hwif->ide_dma_end = &sc1200_ide_dma_end;
|
|
}
|
|
|
|
static const struct ide_port_info sc1200_chipset __devinitdata = {
|
|
.name = "SC1200",
|
|
.init_hwif = init_hwif_sc1200,
|
|
.host_flags = IDE_HFLAG_SERIALIZE |
|
|
IDE_HFLAG_POST_SET_MODE |
|
|
IDE_HFLAG_ABUSE_DMA_MODES,
|
|
.pio_mask = ATA_PIO4,
|
|
.mwdma_mask = ATA_MWDMA2,
|
|
.udma_mask = ATA_UDMA2,
|
|
};
|
|
|
|
static int __devinit sc1200_init_one(struct pci_dev *dev, const struct pci_device_id *id)
|
|
{
|
|
return ide_setup_pci_device(dev, &sc1200_chipset);
|
|
}
|
|
|
|
static const struct pci_device_id sc1200_pci_tbl[] = {
|
|
{ PCI_VDEVICE(NS, PCI_DEVICE_ID_NS_SCx200_IDE), 0},
|
|
{ 0, },
|
|
};
|
|
MODULE_DEVICE_TABLE(pci, sc1200_pci_tbl);
|
|
|
|
static struct pci_driver driver = {
|
|
.name = "SC1200_IDE",
|
|
.id_table = sc1200_pci_tbl,
|
|
.probe = sc1200_init_one,
|
|
#ifdef CONFIG_PM
|
|
.suspend = sc1200_suspend,
|
|
.resume = sc1200_resume,
|
|
#endif
|
|
};
|
|
|
|
static int __init sc1200_ide_init(void)
|
|
{
|
|
return ide_pci_register_driver(&driver);
|
|
}
|
|
|
|
module_init(sc1200_ide_init);
|
|
|
|
MODULE_AUTHOR("Mark Lord");
|
|
MODULE_DESCRIPTION("PCI driver module for NS SC1200 IDE");
|
|
MODULE_LICENSE("GPL");
|