114 lines
3.4 KiB
Plaintext
114 lines
3.4 KiB
Plaintext
# SPDX-License-Identifier: GPL-2.0-only
|
|
#
|
|
# Phy drivers for TI platforms
|
|
#
|
|
config PHY_DA8XX_USB
|
|
tristate "TI DA8xx USB PHY Driver"
|
|
depends on ARCH_DAVINCI_DA8XX || COMPILE_TEST
|
|
select GENERIC_PHY
|
|
select MFD_SYSCON
|
|
help
|
|
Enable this to support the USB PHY on DA8xx SoCs.
|
|
|
|
This driver controls both the USB 1.1 PHY and the USB 2.0 PHY.
|
|
|
|
config PHY_DM816X_USB
|
|
tristate "TI dm816x USB PHY driver"
|
|
depends on ARCH_OMAP2PLUS || COMPILE_TEST
|
|
depends on USB_SUPPORT
|
|
select GENERIC_PHY
|
|
select USB_PHY
|
|
help
|
|
Enable this for dm816x USB to work.
|
|
|
|
config PHY_AM654_SERDES
|
|
tristate "TI AM654 SERDES support"
|
|
depends on OF && ARCH_K3 || COMPILE_TEST
|
|
depends on COMMON_CLK
|
|
select GENERIC_PHY
|
|
select MULTIPLEXER
|
|
select REGMAP_MMIO
|
|
select MUX_MMIO
|
|
help
|
|
This option enables support for TI AM654 SerDes PHY used for
|
|
PCIe.
|
|
|
|
config PHY_J721E_WIZ
|
|
tristate "TI J721E WIZ (SERDES Wrapper) support"
|
|
depends on OF && ARCH_K3 || COMPILE_TEST
|
|
depends on HAS_IOMEM && OF_ADDRESS
|
|
depends on COMMON_CLK
|
|
select GENERIC_PHY
|
|
select MULTIPLEXER
|
|
select REGMAP_MMIO
|
|
select MUX_MMIO
|
|
help
|
|
This option enables support for WIZ module present in TI's J721E
|
|
SoC. WIZ is a serdes wrapper used to configure some of the input
|
|
signals to the SERDES (Sierra/Torrent). This driver configures
|
|
three clock selects (pll0, pll1, dig) and resets for each of the
|
|
lanes.
|
|
|
|
config OMAP_CONTROL_PHY
|
|
tristate "OMAP CONTROL PHY Driver"
|
|
depends on ARCH_OMAP2PLUS || COMPILE_TEST
|
|
help
|
|
Enable this to add support for the PHY part present in the control
|
|
module. This driver has API to power on the USB2 PHY and to write to
|
|
the mailbox. The mailbox is present only in omap4 and the register to
|
|
power on the USB2 PHY is present in OMAP4 and OMAP5. OMAP5 has an
|
|
additional register to power on USB3 PHY/SATA PHY/PCIE PHY
|
|
(PIPE3 PHY).
|
|
|
|
config OMAP_USB2
|
|
tristate "OMAP USB2 PHY Driver"
|
|
depends on ARCH_OMAP2PLUS || ARCH_K3
|
|
depends on USB_SUPPORT
|
|
select GENERIC_PHY
|
|
select USB_PHY
|
|
select OMAP_CONTROL_PHY if ARCH_OMAP2PLUS || COMPILE_TEST
|
|
help
|
|
Enable this to support the transceiver that is part of SOC. This
|
|
driver takes care of all the PHY functionality apart from comparator.
|
|
The USB OTG controller communicates with the comparator using this
|
|
driver.
|
|
|
|
config TI_PIPE3
|
|
tristate "TI PIPE3 PHY Driver"
|
|
depends on ARCH_OMAP2PLUS || COMPILE_TEST
|
|
select GENERIC_PHY
|
|
select OMAP_CONTROL_PHY
|
|
help
|
|
Enable this to support the PIPE3 PHY that is part of TI SOCs. This
|
|
driver takes care of all the PHY functionality apart from comparator.
|
|
This driver interacts with the "OMAP Control PHY Driver" to power
|
|
on/off the PHY.
|
|
|
|
config PHY_TUSB1210
|
|
tristate "TI TUSB1210 ULPI PHY module"
|
|
depends on USB_ULPI_BUS
|
|
select GENERIC_PHY
|
|
help
|
|
Support for TI TUSB1210 USB ULPI PHY.
|
|
|
|
config TWL4030_USB
|
|
tristate "TWL4030 USB Transceiver Driver"
|
|
depends on TWL4030_CORE && REGULATOR_TWL4030 && USB_MUSB_OMAP2PLUS
|
|
depends on USB_SUPPORT
|
|
depends on USB_GADGET || !USB_GADGET # if USB_GADGET=m, this can't 'y'
|
|
select GENERIC_PHY
|
|
select USB_PHY
|
|
help
|
|
Enable this to support the USB OTG transceiver on TWL4030
|
|
family chips (including the TWL5030 and TPS659x0 devices).
|
|
This transceiver supports high and full speed devices plus,
|
|
in host mode, low speed.
|
|
|
|
config PHY_TI_GMII_SEL
|
|
tristate
|
|
select GENERIC_PHY
|
|
select REGMAP
|
|
help
|
|
This driver supports configuring of the TI CPSW Port mode depending on
|
|
the Ethernet PHY connected to the CPSW Port.
|