1449 lines
40 KiB
C
1449 lines
40 KiB
C
// SPDX-License-Identifier: GPL-2.0-or-later
|
|
/*
|
|
* Rockchip USB2.0 PHY with Innosilicon IP block driver
|
|
*
|
|
* Copyright (C) 2016 Fuzhou Rockchip Electronics Co., Ltd
|
|
*/
|
|
|
|
#include <linux/clk.h>
|
|
#include <linux/clk-provider.h>
|
|
#include <linux/delay.h>
|
|
#include <linux/extcon-provider.h>
|
|
#include <linux/interrupt.h>
|
|
#include <linux/io.h>
|
|
#include <linux/gpio/consumer.h>
|
|
#include <linux/jiffies.h>
|
|
#include <linux/kernel.h>
|
|
#include <linux/module.h>
|
|
#include <linux/mutex.h>
|
|
#include <linux/of.h>
|
|
#include <linux/of_address.h>
|
|
#include <linux/of_irq.h>
|
|
#include <linux/of_platform.h>
|
|
#include <linux/phy/phy.h>
|
|
#include <linux/platform_device.h>
|
|
#include <linux/power_supply.h>
|
|
#include <linux/regmap.h>
|
|
#include <linux/mfd/syscon.h>
|
|
#include <linux/usb/of.h>
|
|
#include <linux/usb/otg.h>
|
|
|
|
#define BIT_WRITEABLE_SHIFT 16
|
|
#define SCHEDULE_DELAY (60 * HZ)
|
|
#define OTG_SCHEDULE_DELAY (2 * HZ)
|
|
|
|
enum rockchip_usb2phy_port_id {
|
|
USB2PHY_PORT_OTG,
|
|
USB2PHY_PORT_HOST,
|
|
USB2PHY_NUM_PORTS,
|
|
};
|
|
|
|
enum rockchip_usb2phy_host_state {
|
|
PHY_STATE_HS_ONLINE = 0,
|
|
PHY_STATE_DISCONNECT = 1,
|
|
PHY_STATE_CONNECT = 2,
|
|
PHY_STATE_FS_LS_ONLINE = 4,
|
|
};
|
|
|
|
/**
|
|
* enum usb_chg_state - Different states involved in USB charger detection.
|
|
* @USB_CHG_STATE_UNDEFINED: USB charger is not connected or detection
|
|
* process is not yet started.
|
|
* @USB_CHG_STATE_WAIT_FOR_DCD: Waiting for Data pins contact.
|
|
* @USB_CHG_STATE_DCD_DONE: Data pin contact is detected.
|
|
* @USB_CHG_STATE_PRIMARY_DONE: Primary detection is completed (Detects
|
|
* between SDP and DCP/CDP).
|
|
* @USB_CHG_STATE_SECONDARY_DONE: Secondary detection is completed (Detects
|
|
* between DCP and CDP).
|
|
* @USB_CHG_STATE_DETECTED: USB charger type is determined.
|
|
*/
|
|
enum usb_chg_state {
|
|
USB_CHG_STATE_UNDEFINED = 0,
|
|
USB_CHG_STATE_WAIT_FOR_DCD,
|
|
USB_CHG_STATE_DCD_DONE,
|
|
USB_CHG_STATE_PRIMARY_DONE,
|
|
USB_CHG_STATE_SECONDARY_DONE,
|
|
USB_CHG_STATE_DETECTED,
|
|
};
|
|
|
|
static const unsigned int rockchip_usb2phy_extcon_cable[] = {
|
|
EXTCON_USB,
|
|
EXTCON_USB_HOST,
|
|
EXTCON_CHG_USB_SDP,
|
|
EXTCON_CHG_USB_CDP,
|
|
EXTCON_CHG_USB_DCP,
|
|
EXTCON_CHG_USB_SLOW,
|
|
EXTCON_NONE,
|
|
};
|
|
|
|
struct usb2phy_reg {
|
|
unsigned int offset;
|
|
unsigned int bitend;
|
|
unsigned int bitstart;
|
|
unsigned int disable;
|
|
unsigned int enable;
|
|
};
|
|
|
|
/**
|
|
* struct rockchip_chg_det_reg - usb charger detect registers
|
|
* @cp_det: charging port detected successfully.
|
|
* @dcp_det: dedicated charging port detected successfully.
|
|
* @dp_det: assert data pin connect successfully.
|
|
* @idm_sink_en: open dm sink curren.
|
|
* @idp_sink_en: open dp sink current.
|
|
* @idp_src_en: open dm source current.
|
|
* @rdm_pdwn_en: open dm pull down resistor.
|
|
* @vdm_src_en: open dm voltage source.
|
|
* @vdp_src_en: open dp voltage source.
|
|
* @opmode: utmi operational mode.
|
|
*/
|
|
struct rockchip_chg_det_reg {
|
|
struct usb2phy_reg cp_det;
|
|
struct usb2phy_reg dcp_det;
|
|
struct usb2phy_reg dp_det;
|
|
struct usb2phy_reg idm_sink_en;
|
|
struct usb2phy_reg idp_sink_en;
|
|
struct usb2phy_reg idp_src_en;
|
|
struct usb2phy_reg rdm_pdwn_en;
|
|
struct usb2phy_reg vdm_src_en;
|
|
struct usb2phy_reg vdp_src_en;
|
|
struct usb2phy_reg opmode;
|
|
};
|
|
|
|
/**
|
|
* struct rockchip_usb2phy_port_cfg - usb-phy port configuration.
|
|
* @phy_sus: phy suspend register.
|
|
* @bvalid_det_en: vbus valid rise detection enable register.
|
|
* @bvalid_det_st: vbus valid rise detection status register.
|
|
* @bvalid_det_clr: vbus valid rise detection clear register.
|
|
* @ls_det_en: linestate detection enable register.
|
|
* @ls_det_st: linestate detection state register.
|
|
* @ls_det_clr: linestate detection clear register.
|
|
* @utmi_avalid: utmi vbus avalid status register.
|
|
* @utmi_bvalid: utmi vbus bvalid status register.
|
|
* @utmi_ls: utmi linestate state register.
|
|
* @utmi_hstdet: utmi host disconnect register.
|
|
*/
|
|
struct rockchip_usb2phy_port_cfg {
|
|
struct usb2phy_reg phy_sus;
|
|
struct usb2phy_reg bvalid_det_en;
|
|
struct usb2phy_reg bvalid_det_st;
|
|
struct usb2phy_reg bvalid_det_clr;
|
|
struct usb2phy_reg ls_det_en;
|
|
struct usb2phy_reg ls_det_st;
|
|
struct usb2phy_reg ls_det_clr;
|
|
struct usb2phy_reg utmi_avalid;
|
|
struct usb2phy_reg utmi_bvalid;
|
|
struct usb2phy_reg utmi_ls;
|
|
struct usb2phy_reg utmi_hstdet;
|
|
};
|
|
|
|
/**
|
|
* struct rockchip_usb2phy_cfg - usb-phy configuration.
|
|
* @reg: the address offset of grf for usb-phy config.
|
|
* @num_ports: specify how many ports that the phy has.
|
|
* @clkout_ctl: keep on/turn off output clk of phy.
|
|
* @port_cfgs: usb-phy port configurations.
|
|
* @chg_det: charger detection registers.
|
|
*/
|
|
struct rockchip_usb2phy_cfg {
|
|
unsigned int reg;
|
|
unsigned int num_ports;
|
|
struct usb2phy_reg clkout_ctl;
|
|
const struct rockchip_usb2phy_port_cfg port_cfgs[USB2PHY_NUM_PORTS];
|
|
const struct rockchip_chg_det_reg chg_det;
|
|
};
|
|
|
|
/**
|
|
* struct rockchip_usb2phy_port - usb-phy port data.
|
|
* @phy: generic phy.
|
|
* @port_id: flag for otg port or host port.
|
|
* @suspended: phy suspended flag.
|
|
* @vbus_attached: otg device vbus status.
|
|
* @bvalid_irq: IRQ number assigned for vbus valid rise detection.
|
|
* @ls_irq: IRQ number assigned for linestate detection.
|
|
* @otg_mux_irq: IRQ number which multiplex otg-id/otg-bvalid/linestate
|
|
* irqs to one irq in otg-port.
|
|
* @mutex: for register updating in sm_work.
|
|
* @chg_work: charge detect work.
|
|
* @otg_sm_work: OTG state machine work.
|
|
* @sm_work: HOST state machine work.
|
|
* @port_cfg: port register configuration, assigned by driver data.
|
|
* @event_nb: hold event notification callback.
|
|
* @state: define OTG enumeration states before device reset.
|
|
* @mode: the dr_mode of the controller.
|
|
*/
|
|
struct rockchip_usb2phy_port {
|
|
struct phy *phy;
|
|
unsigned int port_id;
|
|
bool suspended;
|
|
bool vbus_attached;
|
|
int bvalid_irq;
|
|
int ls_irq;
|
|
int otg_mux_irq;
|
|
struct mutex mutex;
|
|
struct delayed_work chg_work;
|
|
struct delayed_work otg_sm_work;
|
|
struct delayed_work sm_work;
|
|
const struct rockchip_usb2phy_port_cfg *port_cfg;
|
|
struct notifier_block event_nb;
|
|
enum usb_otg_state state;
|
|
enum usb_dr_mode mode;
|
|
};
|
|
|
|
/**
|
|
* struct rockchip_usb2phy - usb2.0 phy driver data.
|
|
* @dev: pointer to device.
|
|
* @grf: General Register Files regmap.
|
|
* @usbgrf: USB General Register Files regmap.
|
|
* @clk: clock struct of phy input clk.
|
|
* @clk480m: clock struct of phy output clk.
|
|
* @clk480m_hw: clock struct of phy output clk management.
|
|
* @chg_state: states involved in USB charger detection.
|
|
* @chg_type: USB charger types.
|
|
* @dcd_retries: The retry count used to track Data contact
|
|
* detection process.
|
|
* @edev: extcon device for notification registration
|
|
* @phy_cfg: phy register configuration, assigned by driver data.
|
|
* @ports: phy port instance.
|
|
*/
|
|
struct rockchip_usb2phy {
|
|
struct device *dev;
|
|
struct regmap *grf;
|
|
struct regmap *usbgrf;
|
|
struct clk *clk;
|
|
struct clk *clk480m;
|
|
struct clk_hw clk480m_hw;
|
|
enum usb_chg_state chg_state;
|
|
enum power_supply_type chg_type;
|
|
u8 dcd_retries;
|
|
struct extcon_dev *edev;
|
|
const struct rockchip_usb2phy_cfg *phy_cfg;
|
|
struct rockchip_usb2phy_port ports[USB2PHY_NUM_PORTS];
|
|
};
|
|
|
|
static inline struct regmap *get_reg_base(struct rockchip_usb2phy *rphy)
|
|
{
|
|
return rphy->usbgrf == NULL ? rphy->grf : rphy->usbgrf;
|
|
}
|
|
|
|
static inline int property_enable(struct regmap *base,
|
|
const struct usb2phy_reg *reg, bool en)
|
|
{
|
|
unsigned int val, mask, tmp;
|
|
|
|
tmp = en ? reg->enable : reg->disable;
|
|
mask = GENMASK(reg->bitend, reg->bitstart);
|
|
val = (tmp << reg->bitstart) | (mask << BIT_WRITEABLE_SHIFT);
|
|
|
|
return regmap_write(base, reg->offset, val);
|
|
}
|
|
|
|
static inline bool property_enabled(struct regmap *base,
|
|
const struct usb2phy_reg *reg)
|
|
{
|
|
int ret;
|
|
unsigned int tmp, orig;
|
|
unsigned int mask = GENMASK(reg->bitend, reg->bitstart);
|
|
|
|
ret = regmap_read(base, reg->offset, &orig);
|
|
if (ret)
|
|
return false;
|
|
|
|
tmp = (orig & mask) >> reg->bitstart;
|
|
return tmp == reg->enable;
|
|
}
|
|
|
|
static int rockchip_usb2phy_clk480m_prepare(struct clk_hw *hw)
|
|
{
|
|
struct rockchip_usb2phy *rphy =
|
|
container_of(hw, struct rockchip_usb2phy, clk480m_hw);
|
|
struct regmap *base = get_reg_base(rphy);
|
|
int ret;
|
|
|
|
/* turn on 480m clk output if it is off */
|
|
if (!property_enabled(base, &rphy->phy_cfg->clkout_ctl)) {
|
|
ret = property_enable(base, &rphy->phy_cfg->clkout_ctl, true);
|
|
if (ret)
|
|
return ret;
|
|
|
|
/* waiting for the clk become stable */
|
|
usleep_range(1200, 1300);
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
static void rockchip_usb2phy_clk480m_unprepare(struct clk_hw *hw)
|
|
{
|
|
struct rockchip_usb2phy *rphy =
|
|
container_of(hw, struct rockchip_usb2phy, clk480m_hw);
|
|
struct regmap *base = get_reg_base(rphy);
|
|
|
|
/* turn off 480m clk output */
|
|
property_enable(base, &rphy->phy_cfg->clkout_ctl, false);
|
|
}
|
|
|
|
static int rockchip_usb2phy_clk480m_prepared(struct clk_hw *hw)
|
|
{
|
|
struct rockchip_usb2phy *rphy =
|
|
container_of(hw, struct rockchip_usb2phy, clk480m_hw);
|
|
struct regmap *base = get_reg_base(rphy);
|
|
|
|
return property_enabled(base, &rphy->phy_cfg->clkout_ctl);
|
|
}
|
|
|
|
static unsigned long
|
|
rockchip_usb2phy_clk480m_recalc_rate(struct clk_hw *hw,
|
|
unsigned long parent_rate)
|
|
{
|
|
return 480000000;
|
|
}
|
|
|
|
static const struct clk_ops rockchip_usb2phy_clkout_ops = {
|
|
.prepare = rockchip_usb2phy_clk480m_prepare,
|
|
.unprepare = rockchip_usb2phy_clk480m_unprepare,
|
|
.is_prepared = rockchip_usb2phy_clk480m_prepared,
|
|
.recalc_rate = rockchip_usb2phy_clk480m_recalc_rate,
|
|
};
|
|
|
|
static void rockchip_usb2phy_clk480m_unregister(void *data)
|
|
{
|
|
struct rockchip_usb2phy *rphy = data;
|
|
|
|
of_clk_del_provider(rphy->dev->of_node);
|
|
clk_unregister(rphy->clk480m);
|
|
}
|
|
|
|
static int
|
|
rockchip_usb2phy_clk480m_register(struct rockchip_usb2phy *rphy)
|
|
{
|
|
struct device_node *node = rphy->dev->of_node;
|
|
struct clk_init_data init;
|
|
const char *clk_name;
|
|
int ret;
|
|
|
|
init.flags = 0;
|
|
init.name = "clk_usbphy_480m";
|
|
init.ops = &rockchip_usb2phy_clkout_ops;
|
|
|
|
/* optional override of the clockname */
|
|
of_property_read_string(node, "clock-output-names", &init.name);
|
|
|
|
if (rphy->clk) {
|
|
clk_name = __clk_get_name(rphy->clk);
|
|
init.parent_names = &clk_name;
|
|
init.num_parents = 1;
|
|
} else {
|
|
init.parent_names = NULL;
|
|
init.num_parents = 0;
|
|
}
|
|
|
|
rphy->clk480m_hw.init = &init;
|
|
|
|
/* register the clock */
|
|
rphy->clk480m = clk_register(rphy->dev, &rphy->clk480m_hw);
|
|
if (IS_ERR(rphy->clk480m)) {
|
|
ret = PTR_ERR(rphy->clk480m);
|
|
goto err_ret;
|
|
}
|
|
|
|
ret = of_clk_add_provider(node, of_clk_src_simple_get, rphy->clk480m);
|
|
if (ret < 0)
|
|
goto err_clk_provider;
|
|
|
|
ret = devm_add_action(rphy->dev, rockchip_usb2phy_clk480m_unregister,
|
|
rphy);
|
|
if (ret < 0)
|
|
goto err_unreg_action;
|
|
|
|
return 0;
|
|
|
|
err_unreg_action:
|
|
of_clk_del_provider(node);
|
|
err_clk_provider:
|
|
clk_unregister(rphy->clk480m);
|
|
err_ret:
|
|
return ret;
|
|
}
|
|
|
|
static int rockchip_usb2phy_extcon_register(struct rockchip_usb2phy *rphy)
|
|
{
|
|
int ret;
|
|
struct device_node *node = rphy->dev->of_node;
|
|
struct extcon_dev *edev;
|
|
|
|
if (of_property_read_bool(node, "extcon")) {
|
|
edev = extcon_get_edev_by_phandle(rphy->dev, 0);
|
|
if (IS_ERR(edev)) {
|
|
if (PTR_ERR(edev) != -EPROBE_DEFER)
|
|
dev_err(rphy->dev, "Invalid or missing extcon\n");
|
|
return PTR_ERR(edev);
|
|
}
|
|
} else {
|
|
/* Initialize extcon device */
|
|
edev = devm_extcon_dev_allocate(rphy->dev,
|
|
rockchip_usb2phy_extcon_cable);
|
|
|
|
if (IS_ERR(edev))
|
|
return -ENOMEM;
|
|
|
|
ret = devm_extcon_dev_register(rphy->dev, edev);
|
|
if (ret) {
|
|
dev_err(rphy->dev, "failed to register extcon device\n");
|
|
return ret;
|
|
}
|
|
}
|
|
|
|
rphy->edev = edev;
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int rockchip_usb2phy_init(struct phy *phy)
|
|
{
|
|
struct rockchip_usb2phy_port *rport = phy_get_drvdata(phy);
|
|
struct rockchip_usb2phy *rphy = dev_get_drvdata(phy->dev.parent);
|
|
int ret = 0;
|
|
|
|
mutex_lock(&rport->mutex);
|
|
|
|
if (rport->port_id == USB2PHY_PORT_OTG) {
|
|
if (rport->mode != USB_DR_MODE_HOST &&
|
|
rport->mode != USB_DR_MODE_UNKNOWN) {
|
|
/* clear bvalid status and enable bvalid detect irq */
|
|
ret = property_enable(rphy->grf,
|
|
&rport->port_cfg->bvalid_det_clr,
|
|
true);
|
|
if (ret)
|
|
goto out;
|
|
|
|
ret = property_enable(rphy->grf,
|
|
&rport->port_cfg->bvalid_det_en,
|
|
true);
|
|
if (ret)
|
|
goto out;
|
|
|
|
schedule_delayed_work(&rport->otg_sm_work,
|
|
OTG_SCHEDULE_DELAY * 3);
|
|
} else {
|
|
/* If OTG works in host only mode, do nothing. */
|
|
dev_dbg(&rport->phy->dev, "mode %d\n", rport->mode);
|
|
}
|
|
} else if (rport->port_id == USB2PHY_PORT_HOST) {
|
|
/* clear linestate and enable linestate detect irq */
|
|
ret = property_enable(rphy->grf,
|
|
&rport->port_cfg->ls_det_clr, true);
|
|
if (ret)
|
|
goto out;
|
|
|
|
ret = property_enable(rphy->grf,
|
|
&rport->port_cfg->ls_det_en, true);
|
|
if (ret)
|
|
goto out;
|
|
|
|
schedule_delayed_work(&rport->sm_work, SCHEDULE_DELAY);
|
|
}
|
|
|
|
out:
|
|
mutex_unlock(&rport->mutex);
|
|
return ret;
|
|
}
|
|
|
|
static int rockchip_usb2phy_power_on(struct phy *phy)
|
|
{
|
|
struct rockchip_usb2phy_port *rport = phy_get_drvdata(phy);
|
|
struct rockchip_usb2phy *rphy = dev_get_drvdata(phy->dev.parent);
|
|
struct regmap *base = get_reg_base(rphy);
|
|
int ret;
|
|
|
|
dev_dbg(&rport->phy->dev, "port power on\n");
|
|
|
|
if (!rport->suspended)
|
|
return 0;
|
|
|
|
ret = clk_prepare_enable(rphy->clk480m);
|
|
if (ret)
|
|
return ret;
|
|
|
|
ret = property_enable(base, &rport->port_cfg->phy_sus, false);
|
|
if (ret) {
|
|
clk_disable_unprepare(rphy->clk480m);
|
|
return ret;
|
|
}
|
|
|
|
/* waiting for the utmi_clk to become stable */
|
|
usleep_range(1500, 2000);
|
|
|
|
rport->suspended = false;
|
|
return 0;
|
|
}
|
|
|
|
static int rockchip_usb2phy_power_off(struct phy *phy)
|
|
{
|
|
struct rockchip_usb2phy_port *rport = phy_get_drvdata(phy);
|
|
struct rockchip_usb2phy *rphy = dev_get_drvdata(phy->dev.parent);
|
|
struct regmap *base = get_reg_base(rphy);
|
|
int ret;
|
|
|
|
dev_dbg(&rport->phy->dev, "port power off\n");
|
|
|
|
if (rport->suspended)
|
|
return 0;
|
|
|
|
ret = property_enable(base, &rport->port_cfg->phy_sus, true);
|
|
if (ret)
|
|
return ret;
|
|
|
|
rport->suspended = true;
|
|
clk_disable_unprepare(rphy->clk480m);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int rockchip_usb2phy_exit(struct phy *phy)
|
|
{
|
|
struct rockchip_usb2phy_port *rport = phy_get_drvdata(phy);
|
|
|
|
if (rport->port_id == USB2PHY_PORT_OTG &&
|
|
rport->mode != USB_DR_MODE_HOST &&
|
|
rport->mode != USB_DR_MODE_UNKNOWN) {
|
|
cancel_delayed_work_sync(&rport->otg_sm_work);
|
|
cancel_delayed_work_sync(&rport->chg_work);
|
|
} else if (rport->port_id == USB2PHY_PORT_HOST)
|
|
cancel_delayed_work_sync(&rport->sm_work);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static const struct phy_ops rockchip_usb2phy_ops = {
|
|
.init = rockchip_usb2phy_init,
|
|
.exit = rockchip_usb2phy_exit,
|
|
.power_on = rockchip_usb2phy_power_on,
|
|
.power_off = rockchip_usb2phy_power_off,
|
|
.owner = THIS_MODULE,
|
|
};
|
|
|
|
static void rockchip_usb2phy_otg_sm_work(struct work_struct *work)
|
|
{
|
|
struct rockchip_usb2phy_port *rport =
|
|
container_of(work, struct rockchip_usb2phy_port,
|
|
otg_sm_work.work);
|
|
struct rockchip_usb2phy *rphy = dev_get_drvdata(rport->phy->dev.parent);
|
|
static unsigned int cable;
|
|
unsigned long delay;
|
|
bool vbus_attach, sch_work, notify_charger;
|
|
|
|
vbus_attach = property_enabled(rphy->grf,
|
|
&rport->port_cfg->utmi_bvalid);
|
|
|
|
sch_work = false;
|
|
notify_charger = false;
|
|
delay = OTG_SCHEDULE_DELAY;
|
|
dev_dbg(&rport->phy->dev, "%s otg sm work\n",
|
|
usb_otg_state_string(rport->state));
|
|
|
|
switch (rport->state) {
|
|
case OTG_STATE_UNDEFINED:
|
|
rport->state = OTG_STATE_B_IDLE;
|
|
if (!vbus_attach)
|
|
rockchip_usb2phy_power_off(rport->phy);
|
|
/* fall through */
|
|
case OTG_STATE_B_IDLE:
|
|
if (extcon_get_state(rphy->edev, EXTCON_USB_HOST) > 0) {
|
|
dev_dbg(&rport->phy->dev, "usb otg host connect\n");
|
|
rport->state = OTG_STATE_A_HOST;
|
|
rockchip_usb2phy_power_on(rport->phy);
|
|
return;
|
|
} else if (vbus_attach) {
|
|
dev_dbg(&rport->phy->dev, "vbus_attach\n");
|
|
switch (rphy->chg_state) {
|
|
case USB_CHG_STATE_UNDEFINED:
|
|
schedule_delayed_work(&rport->chg_work, 0);
|
|
return;
|
|
case USB_CHG_STATE_DETECTED:
|
|
switch (rphy->chg_type) {
|
|
case POWER_SUPPLY_TYPE_USB:
|
|
dev_dbg(&rport->phy->dev, "sdp cable is connected\n");
|
|
rockchip_usb2phy_power_on(rport->phy);
|
|
rport->state = OTG_STATE_B_PERIPHERAL;
|
|
notify_charger = true;
|
|
sch_work = true;
|
|
cable = EXTCON_CHG_USB_SDP;
|
|
break;
|
|
case POWER_SUPPLY_TYPE_USB_DCP:
|
|
dev_dbg(&rport->phy->dev, "dcp cable is connected\n");
|
|
rockchip_usb2phy_power_off(rport->phy);
|
|
notify_charger = true;
|
|
sch_work = true;
|
|
cable = EXTCON_CHG_USB_DCP;
|
|
break;
|
|
case POWER_SUPPLY_TYPE_USB_CDP:
|
|
dev_dbg(&rport->phy->dev, "cdp cable is connected\n");
|
|
rockchip_usb2phy_power_on(rport->phy);
|
|
rport->state = OTG_STATE_B_PERIPHERAL;
|
|
notify_charger = true;
|
|
sch_work = true;
|
|
cable = EXTCON_CHG_USB_CDP;
|
|
break;
|
|
default:
|
|
break;
|
|
}
|
|
break;
|
|
default:
|
|
break;
|
|
}
|
|
} else {
|
|
notify_charger = true;
|
|
rphy->chg_state = USB_CHG_STATE_UNDEFINED;
|
|
rphy->chg_type = POWER_SUPPLY_TYPE_UNKNOWN;
|
|
}
|
|
|
|
if (rport->vbus_attached != vbus_attach) {
|
|
rport->vbus_attached = vbus_attach;
|
|
|
|
if (notify_charger && rphy->edev) {
|
|
extcon_set_state_sync(rphy->edev,
|
|
cable, vbus_attach);
|
|
if (cable == EXTCON_CHG_USB_SDP)
|
|
extcon_set_state_sync(rphy->edev,
|
|
EXTCON_USB,
|
|
vbus_attach);
|
|
}
|
|
}
|
|
break;
|
|
case OTG_STATE_B_PERIPHERAL:
|
|
if (!vbus_attach) {
|
|
dev_dbg(&rport->phy->dev, "usb disconnect\n");
|
|
rphy->chg_state = USB_CHG_STATE_UNDEFINED;
|
|
rphy->chg_type = POWER_SUPPLY_TYPE_UNKNOWN;
|
|
rport->state = OTG_STATE_B_IDLE;
|
|
delay = 0;
|
|
rockchip_usb2phy_power_off(rport->phy);
|
|
}
|
|
sch_work = true;
|
|
break;
|
|
case OTG_STATE_A_HOST:
|
|
if (extcon_get_state(rphy->edev, EXTCON_USB_HOST) == 0) {
|
|
dev_dbg(&rport->phy->dev, "usb otg host disconnect\n");
|
|
rport->state = OTG_STATE_B_IDLE;
|
|
rockchip_usb2phy_power_off(rport->phy);
|
|
}
|
|
break;
|
|
default:
|
|
break;
|
|
}
|
|
|
|
if (sch_work)
|
|
schedule_delayed_work(&rport->otg_sm_work, delay);
|
|
}
|
|
|
|
static const char *chg_to_string(enum power_supply_type chg_type)
|
|
{
|
|
switch (chg_type) {
|
|
case POWER_SUPPLY_TYPE_USB:
|
|
return "USB_SDP_CHARGER";
|
|
case POWER_SUPPLY_TYPE_USB_DCP:
|
|
return "USB_DCP_CHARGER";
|
|
case POWER_SUPPLY_TYPE_USB_CDP:
|
|
return "USB_CDP_CHARGER";
|
|
default:
|
|
return "INVALID_CHARGER";
|
|
}
|
|
}
|
|
|
|
static void rockchip_chg_enable_dcd(struct rockchip_usb2phy *rphy,
|
|
bool en)
|
|
{
|
|
struct regmap *base = get_reg_base(rphy);
|
|
|
|
property_enable(base, &rphy->phy_cfg->chg_det.rdm_pdwn_en, en);
|
|
property_enable(base, &rphy->phy_cfg->chg_det.idp_src_en, en);
|
|
}
|
|
|
|
static void rockchip_chg_enable_primary_det(struct rockchip_usb2phy *rphy,
|
|
bool en)
|
|
{
|
|
struct regmap *base = get_reg_base(rphy);
|
|
|
|
property_enable(base, &rphy->phy_cfg->chg_det.vdp_src_en, en);
|
|
property_enable(base, &rphy->phy_cfg->chg_det.idm_sink_en, en);
|
|
}
|
|
|
|
static void rockchip_chg_enable_secondary_det(struct rockchip_usb2phy *rphy,
|
|
bool en)
|
|
{
|
|
struct regmap *base = get_reg_base(rphy);
|
|
|
|
property_enable(base, &rphy->phy_cfg->chg_det.vdm_src_en, en);
|
|
property_enable(base, &rphy->phy_cfg->chg_det.idp_sink_en, en);
|
|
}
|
|
|
|
#define CHG_DCD_POLL_TIME (100 * HZ / 1000)
|
|
#define CHG_DCD_MAX_RETRIES 6
|
|
#define CHG_PRIMARY_DET_TIME (40 * HZ / 1000)
|
|
#define CHG_SECONDARY_DET_TIME (40 * HZ / 1000)
|
|
static void rockchip_chg_detect_work(struct work_struct *work)
|
|
{
|
|
struct rockchip_usb2phy_port *rport =
|
|
container_of(work, struct rockchip_usb2phy_port, chg_work.work);
|
|
struct rockchip_usb2phy *rphy = dev_get_drvdata(rport->phy->dev.parent);
|
|
struct regmap *base = get_reg_base(rphy);
|
|
bool is_dcd, tmout, vout;
|
|
unsigned long delay;
|
|
|
|
dev_dbg(&rport->phy->dev, "chg detection work state = %d\n",
|
|
rphy->chg_state);
|
|
switch (rphy->chg_state) {
|
|
case USB_CHG_STATE_UNDEFINED:
|
|
if (!rport->suspended)
|
|
rockchip_usb2phy_power_off(rport->phy);
|
|
/* put the controller in non-driving mode */
|
|
property_enable(base, &rphy->phy_cfg->chg_det.opmode, false);
|
|
/* Start DCD processing stage 1 */
|
|
rockchip_chg_enable_dcd(rphy, true);
|
|
rphy->chg_state = USB_CHG_STATE_WAIT_FOR_DCD;
|
|
rphy->dcd_retries = 0;
|
|
delay = CHG_DCD_POLL_TIME;
|
|
break;
|
|
case USB_CHG_STATE_WAIT_FOR_DCD:
|
|
/* get data contact detection status */
|
|
is_dcd = property_enabled(rphy->grf,
|
|
&rphy->phy_cfg->chg_det.dp_det);
|
|
tmout = ++rphy->dcd_retries == CHG_DCD_MAX_RETRIES;
|
|
/* stage 2 */
|
|
if (is_dcd || tmout) {
|
|
/* stage 4 */
|
|
/* Turn off DCD circuitry */
|
|
rockchip_chg_enable_dcd(rphy, false);
|
|
/* Voltage Source on DP, Probe on DM */
|
|
rockchip_chg_enable_primary_det(rphy, true);
|
|
delay = CHG_PRIMARY_DET_TIME;
|
|
rphy->chg_state = USB_CHG_STATE_DCD_DONE;
|
|
} else {
|
|
/* stage 3 */
|
|
delay = CHG_DCD_POLL_TIME;
|
|
}
|
|
break;
|
|
case USB_CHG_STATE_DCD_DONE:
|
|
vout = property_enabled(rphy->grf,
|
|
&rphy->phy_cfg->chg_det.cp_det);
|
|
rockchip_chg_enable_primary_det(rphy, false);
|
|
if (vout) {
|
|
/* Voltage Source on DM, Probe on DP */
|
|
rockchip_chg_enable_secondary_det(rphy, true);
|
|
delay = CHG_SECONDARY_DET_TIME;
|
|
rphy->chg_state = USB_CHG_STATE_PRIMARY_DONE;
|
|
} else {
|
|
if (rphy->dcd_retries == CHG_DCD_MAX_RETRIES) {
|
|
/* floating charger found */
|
|
rphy->chg_type = POWER_SUPPLY_TYPE_USB_DCP;
|
|
rphy->chg_state = USB_CHG_STATE_DETECTED;
|
|
delay = 0;
|
|
} else {
|
|
rphy->chg_type = POWER_SUPPLY_TYPE_USB;
|
|
rphy->chg_state = USB_CHG_STATE_DETECTED;
|
|
delay = 0;
|
|
}
|
|
}
|
|
break;
|
|
case USB_CHG_STATE_PRIMARY_DONE:
|
|
vout = property_enabled(rphy->grf,
|
|
&rphy->phy_cfg->chg_det.dcp_det);
|
|
/* Turn off voltage source */
|
|
rockchip_chg_enable_secondary_det(rphy, false);
|
|
if (vout)
|
|
rphy->chg_type = POWER_SUPPLY_TYPE_USB_DCP;
|
|
else
|
|
rphy->chg_type = POWER_SUPPLY_TYPE_USB_CDP;
|
|
/* fall through */
|
|
case USB_CHG_STATE_SECONDARY_DONE:
|
|
rphy->chg_state = USB_CHG_STATE_DETECTED;
|
|
delay = 0;
|
|
/* fall through */
|
|
case USB_CHG_STATE_DETECTED:
|
|
/* put the controller in normal mode */
|
|
property_enable(base, &rphy->phy_cfg->chg_det.opmode, true);
|
|
rockchip_usb2phy_otg_sm_work(&rport->otg_sm_work.work);
|
|
dev_info(&rport->phy->dev, "charger = %s\n",
|
|
chg_to_string(rphy->chg_type));
|
|
return;
|
|
default:
|
|
return;
|
|
}
|
|
|
|
schedule_delayed_work(&rport->chg_work, delay);
|
|
}
|
|
|
|
/*
|
|
* The function manage host-phy port state and suspend/resume phy port
|
|
* to save power.
|
|
*
|
|
* we rely on utmi_linestate and utmi_hostdisconnect to identify whether
|
|
* devices is disconnect or not. Besides, we do not need care it is FS/LS
|
|
* disconnected or HS disconnected, actually, we just only need get the
|
|
* device is disconnected at last through rearm the delayed work,
|
|
* to suspend the phy port in _PHY_STATE_DISCONNECT_ case.
|
|
*
|
|
* NOTE: It may invoke *phy_powr_off or *phy_power_on which will invoke
|
|
* some clk related APIs, so do not invoke it from interrupt context directly.
|
|
*/
|
|
static void rockchip_usb2phy_sm_work(struct work_struct *work)
|
|
{
|
|
struct rockchip_usb2phy_port *rport =
|
|
container_of(work, struct rockchip_usb2phy_port, sm_work.work);
|
|
struct rockchip_usb2phy *rphy = dev_get_drvdata(rport->phy->dev.parent);
|
|
unsigned int sh = rport->port_cfg->utmi_hstdet.bitend -
|
|
rport->port_cfg->utmi_hstdet.bitstart + 1;
|
|
unsigned int ul, uhd, state;
|
|
unsigned int ul_mask, uhd_mask;
|
|
int ret;
|
|
|
|
mutex_lock(&rport->mutex);
|
|
|
|
ret = regmap_read(rphy->grf, rport->port_cfg->utmi_ls.offset, &ul);
|
|
if (ret < 0)
|
|
goto next_schedule;
|
|
|
|
ret = regmap_read(rphy->grf, rport->port_cfg->utmi_hstdet.offset, &uhd);
|
|
if (ret < 0)
|
|
goto next_schedule;
|
|
|
|
uhd_mask = GENMASK(rport->port_cfg->utmi_hstdet.bitend,
|
|
rport->port_cfg->utmi_hstdet.bitstart);
|
|
ul_mask = GENMASK(rport->port_cfg->utmi_ls.bitend,
|
|
rport->port_cfg->utmi_ls.bitstart);
|
|
|
|
/* stitch on utmi_ls and utmi_hstdet as phy state */
|
|
state = ((uhd & uhd_mask) >> rport->port_cfg->utmi_hstdet.bitstart) |
|
|
(((ul & ul_mask) >> rport->port_cfg->utmi_ls.bitstart) << sh);
|
|
|
|
switch (state) {
|
|
case PHY_STATE_HS_ONLINE:
|
|
dev_dbg(&rport->phy->dev, "HS online\n");
|
|
break;
|
|
case PHY_STATE_FS_LS_ONLINE:
|
|
/*
|
|
* For FS/LS device, the online state share with connect state
|
|
* from utmi_ls and utmi_hstdet register, so we distinguish
|
|
* them via suspended flag.
|
|
*
|
|
* Plus, there are two cases, one is D- Line pull-up, and D+
|
|
* line pull-down, the state is 4; another is D+ line pull-up,
|
|
* and D- line pull-down, the state is 2.
|
|
*/
|
|
if (!rport->suspended) {
|
|
/* D- line pull-up, D+ line pull-down */
|
|
dev_dbg(&rport->phy->dev, "FS/LS online\n");
|
|
break;
|
|
}
|
|
/* fall through */
|
|
case PHY_STATE_CONNECT:
|
|
if (rport->suspended) {
|
|
dev_dbg(&rport->phy->dev, "Connected\n");
|
|
rockchip_usb2phy_power_on(rport->phy);
|
|
rport->suspended = false;
|
|
} else {
|
|
/* D+ line pull-up, D- line pull-down */
|
|
dev_dbg(&rport->phy->dev, "FS/LS online\n");
|
|
}
|
|
break;
|
|
case PHY_STATE_DISCONNECT:
|
|
if (!rport->suspended) {
|
|
dev_dbg(&rport->phy->dev, "Disconnected\n");
|
|
rockchip_usb2phy_power_off(rport->phy);
|
|
rport->suspended = true;
|
|
}
|
|
|
|
/*
|
|
* activate the linestate detection to get the next device
|
|
* plug-in irq.
|
|
*/
|
|
property_enable(rphy->grf, &rport->port_cfg->ls_det_clr, true);
|
|
property_enable(rphy->grf, &rport->port_cfg->ls_det_en, true);
|
|
|
|
/*
|
|
* we don't need to rearm the delayed work when the phy port
|
|
* is suspended.
|
|
*/
|
|
mutex_unlock(&rport->mutex);
|
|
return;
|
|
default:
|
|
dev_dbg(&rport->phy->dev, "unknown phy state\n");
|
|
break;
|
|
}
|
|
|
|
next_schedule:
|
|
mutex_unlock(&rport->mutex);
|
|
schedule_delayed_work(&rport->sm_work, SCHEDULE_DELAY);
|
|
}
|
|
|
|
static irqreturn_t rockchip_usb2phy_linestate_irq(int irq, void *data)
|
|
{
|
|
struct rockchip_usb2phy_port *rport = data;
|
|
struct rockchip_usb2phy *rphy = dev_get_drvdata(rport->phy->dev.parent);
|
|
|
|
if (!property_enabled(rphy->grf, &rport->port_cfg->ls_det_st))
|
|
return IRQ_NONE;
|
|
|
|
mutex_lock(&rport->mutex);
|
|
|
|
/* disable linestate detect irq and clear its status */
|
|
property_enable(rphy->grf, &rport->port_cfg->ls_det_en, false);
|
|
property_enable(rphy->grf, &rport->port_cfg->ls_det_clr, true);
|
|
|
|
mutex_unlock(&rport->mutex);
|
|
|
|
/*
|
|
* In this case for host phy port, a new device is plugged in,
|
|
* meanwhile, if the phy port is suspended, we need rearm the work to
|
|
* resume it and mange its states; otherwise, we do nothing about that.
|
|
*/
|
|
if (rport->suspended && rport->port_id == USB2PHY_PORT_HOST)
|
|
rockchip_usb2phy_sm_work(&rport->sm_work.work);
|
|
|
|
return IRQ_HANDLED;
|
|
}
|
|
|
|
static irqreturn_t rockchip_usb2phy_bvalid_irq(int irq, void *data)
|
|
{
|
|
struct rockchip_usb2phy_port *rport = data;
|
|
struct rockchip_usb2phy *rphy = dev_get_drvdata(rport->phy->dev.parent);
|
|
|
|
if (!property_enabled(rphy->grf, &rport->port_cfg->bvalid_det_st))
|
|
return IRQ_NONE;
|
|
|
|
mutex_lock(&rport->mutex);
|
|
|
|
/* clear bvalid detect irq pending status */
|
|
property_enable(rphy->grf, &rport->port_cfg->bvalid_det_clr, true);
|
|
|
|
mutex_unlock(&rport->mutex);
|
|
|
|
rockchip_usb2phy_otg_sm_work(&rport->otg_sm_work.work);
|
|
|
|
return IRQ_HANDLED;
|
|
}
|
|
|
|
static irqreturn_t rockchip_usb2phy_otg_mux_irq(int irq, void *data)
|
|
{
|
|
struct rockchip_usb2phy_port *rport = data;
|
|
struct rockchip_usb2phy *rphy = dev_get_drvdata(rport->phy->dev.parent);
|
|
|
|
if (property_enabled(rphy->grf, &rport->port_cfg->bvalid_det_st))
|
|
return rockchip_usb2phy_bvalid_irq(irq, data);
|
|
else
|
|
return IRQ_NONE;
|
|
}
|
|
|
|
static int rockchip_usb2phy_host_port_init(struct rockchip_usb2phy *rphy,
|
|
struct rockchip_usb2phy_port *rport,
|
|
struct device_node *child_np)
|
|
{
|
|
int ret;
|
|
|
|
rport->port_id = USB2PHY_PORT_HOST;
|
|
rport->port_cfg = &rphy->phy_cfg->port_cfgs[USB2PHY_PORT_HOST];
|
|
rport->suspended = true;
|
|
|
|
mutex_init(&rport->mutex);
|
|
INIT_DELAYED_WORK(&rport->sm_work, rockchip_usb2phy_sm_work);
|
|
|
|
rport->ls_irq = of_irq_get_byname(child_np, "linestate");
|
|
if (rport->ls_irq < 0) {
|
|
dev_err(rphy->dev, "no linestate irq provided\n");
|
|
return rport->ls_irq;
|
|
}
|
|
|
|
ret = devm_request_threaded_irq(rphy->dev, rport->ls_irq, NULL,
|
|
rockchip_usb2phy_linestate_irq,
|
|
IRQF_ONESHOT,
|
|
"rockchip_usb2phy", rport);
|
|
if (ret) {
|
|
dev_err(rphy->dev, "failed to request linestate irq handle\n");
|
|
return ret;
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int rockchip_otg_event(struct notifier_block *nb,
|
|
unsigned long event, void *ptr)
|
|
{
|
|
struct rockchip_usb2phy_port *rport =
|
|
container_of(nb, struct rockchip_usb2phy_port, event_nb);
|
|
|
|
schedule_delayed_work(&rport->otg_sm_work, OTG_SCHEDULE_DELAY);
|
|
|
|
return NOTIFY_DONE;
|
|
}
|
|
|
|
static int rockchip_usb2phy_otg_port_init(struct rockchip_usb2phy *rphy,
|
|
struct rockchip_usb2phy_port *rport,
|
|
struct device_node *child_np)
|
|
{
|
|
int ret;
|
|
|
|
rport->port_id = USB2PHY_PORT_OTG;
|
|
rport->port_cfg = &rphy->phy_cfg->port_cfgs[USB2PHY_PORT_OTG];
|
|
rport->state = OTG_STATE_UNDEFINED;
|
|
|
|
/*
|
|
* set suspended flag to true, but actually don't
|
|
* put phy in suspend mode, it aims to enable usb
|
|
* phy and clock in power_on() called by usb controller
|
|
* driver during probe.
|
|
*/
|
|
rport->suspended = true;
|
|
rport->vbus_attached = false;
|
|
|
|
mutex_init(&rport->mutex);
|
|
|
|
rport->mode = of_usb_get_dr_mode_by_phy(child_np, -1);
|
|
if (rport->mode == USB_DR_MODE_HOST ||
|
|
rport->mode == USB_DR_MODE_UNKNOWN) {
|
|
ret = 0;
|
|
goto out;
|
|
}
|
|
|
|
INIT_DELAYED_WORK(&rport->chg_work, rockchip_chg_detect_work);
|
|
INIT_DELAYED_WORK(&rport->otg_sm_work, rockchip_usb2phy_otg_sm_work);
|
|
|
|
/*
|
|
* Some SoCs use one interrupt with otg-id/otg-bvalid/linestate
|
|
* interrupts muxed together, so probe the otg-mux interrupt first,
|
|
* if not found, then look for the regular interrupts one by one.
|
|
*/
|
|
rport->otg_mux_irq = of_irq_get_byname(child_np, "otg-mux");
|
|
if (rport->otg_mux_irq > 0) {
|
|
ret = devm_request_threaded_irq(rphy->dev, rport->otg_mux_irq,
|
|
NULL,
|
|
rockchip_usb2phy_otg_mux_irq,
|
|
IRQF_ONESHOT,
|
|
"rockchip_usb2phy_otg",
|
|
rport);
|
|
if (ret) {
|
|
dev_err(rphy->dev,
|
|
"failed to request otg-mux irq handle\n");
|
|
goto out;
|
|
}
|
|
} else {
|
|
rport->bvalid_irq = of_irq_get_byname(child_np, "otg-bvalid");
|
|
if (rport->bvalid_irq < 0) {
|
|
dev_err(rphy->dev, "no vbus valid irq provided\n");
|
|
ret = rport->bvalid_irq;
|
|
goto out;
|
|
}
|
|
|
|
ret = devm_request_threaded_irq(rphy->dev, rport->bvalid_irq,
|
|
NULL,
|
|
rockchip_usb2phy_bvalid_irq,
|
|
IRQF_ONESHOT,
|
|
"rockchip_usb2phy_bvalid",
|
|
rport);
|
|
if (ret) {
|
|
dev_err(rphy->dev,
|
|
"failed to request otg-bvalid irq handle\n");
|
|
goto out;
|
|
}
|
|
}
|
|
|
|
if (!IS_ERR(rphy->edev)) {
|
|
rport->event_nb.notifier_call = rockchip_otg_event;
|
|
|
|
ret = devm_extcon_register_notifier(rphy->dev, rphy->edev,
|
|
EXTCON_USB_HOST, &rport->event_nb);
|
|
if (ret)
|
|
dev_err(rphy->dev, "register USB HOST notifier failed\n");
|
|
}
|
|
|
|
out:
|
|
return ret;
|
|
}
|
|
|
|
static int rockchip_usb2phy_probe(struct platform_device *pdev)
|
|
{
|
|
struct device *dev = &pdev->dev;
|
|
struct device_node *np = dev->of_node;
|
|
struct device_node *child_np;
|
|
struct phy_provider *provider;
|
|
struct rockchip_usb2phy *rphy;
|
|
const struct rockchip_usb2phy_cfg *phy_cfgs;
|
|
const struct of_device_id *match;
|
|
unsigned int reg;
|
|
int index, ret;
|
|
|
|
rphy = devm_kzalloc(dev, sizeof(*rphy), GFP_KERNEL);
|
|
if (!rphy)
|
|
return -ENOMEM;
|
|
|
|
match = of_match_device(dev->driver->of_match_table, dev);
|
|
if (!match || !match->data) {
|
|
dev_err(dev, "phy configs are not assigned!\n");
|
|
return -EINVAL;
|
|
}
|
|
|
|
if (!dev->parent || !dev->parent->of_node)
|
|
return -EINVAL;
|
|
|
|
rphy->grf = syscon_node_to_regmap(dev->parent->of_node);
|
|
if (IS_ERR(rphy->grf))
|
|
return PTR_ERR(rphy->grf);
|
|
|
|
if (of_device_is_compatible(np, "rockchip,rv1108-usb2phy")) {
|
|
rphy->usbgrf =
|
|
syscon_regmap_lookup_by_phandle(dev->of_node,
|
|
"rockchip,usbgrf");
|
|
if (IS_ERR(rphy->usbgrf))
|
|
return PTR_ERR(rphy->usbgrf);
|
|
} else {
|
|
rphy->usbgrf = NULL;
|
|
}
|
|
|
|
if (of_property_read_u32(np, "reg", ®)) {
|
|
dev_err(dev, "the reg property is not assigned in %pOFn node\n",
|
|
np);
|
|
return -EINVAL;
|
|
}
|
|
|
|
rphy->dev = dev;
|
|
phy_cfgs = match->data;
|
|
rphy->chg_state = USB_CHG_STATE_UNDEFINED;
|
|
rphy->chg_type = POWER_SUPPLY_TYPE_UNKNOWN;
|
|
platform_set_drvdata(pdev, rphy);
|
|
|
|
ret = rockchip_usb2phy_extcon_register(rphy);
|
|
if (ret)
|
|
return ret;
|
|
|
|
/* find out a proper config which can be matched with dt. */
|
|
index = 0;
|
|
while (phy_cfgs[index].reg) {
|
|
if (phy_cfgs[index].reg == reg) {
|
|
rphy->phy_cfg = &phy_cfgs[index];
|
|
break;
|
|
}
|
|
|
|
++index;
|
|
}
|
|
|
|
if (!rphy->phy_cfg) {
|
|
dev_err(dev, "no phy-config can be matched with %pOFn node\n",
|
|
np);
|
|
return -EINVAL;
|
|
}
|
|
|
|
rphy->clk = of_clk_get_by_name(np, "phyclk");
|
|
if (!IS_ERR(rphy->clk)) {
|
|
clk_prepare_enable(rphy->clk);
|
|
} else {
|
|
dev_info(&pdev->dev, "no phyclk specified\n");
|
|
rphy->clk = NULL;
|
|
}
|
|
|
|
ret = rockchip_usb2phy_clk480m_register(rphy);
|
|
if (ret) {
|
|
dev_err(dev, "failed to register 480m output clock\n");
|
|
goto disable_clks;
|
|
}
|
|
|
|
index = 0;
|
|
for_each_available_child_of_node(np, child_np) {
|
|
struct rockchip_usb2phy_port *rport = &rphy->ports[index];
|
|
struct phy *phy;
|
|
|
|
/* This driver aims to support both otg-port and host-port */
|
|
if (!of_node_name_eq(child_np, "host-port") &&
|
|
!of_node_name_eq(child_np, "otg-port"))
|
|
goto next_child;
|
|
|
|
phy = devm_phy_create(dev, child_np, &rockchip_usb2phy_ops);
|
|
if (IS_ERR(phy)) {
|
|
dev_err(dev, "failed to create phy\n");
|
|
ret = PTR_ERR(phy);
|
|
goto put_child;
|
|
}
|
|
|
|
rport->phy = phy;
|
|
phy_set_drvdata(rport->phy, rport);
|
|
|
|
/* initialize otg/host port separately */
|
|
if (of_node_name_eq(child_np, "host-port")) {
|
|
ret = rockchip_usb2phy_host_port_init(rphy, rport,
|
|
child_np);
|
|
if (ret)
|
|
goto put_child;
|
|
} else {
|
|
ret = rockchip_usb2phy_otg_port_init(rphy, rport,
|
|
child_np);
|
|
if (ret)
|
|
goto put_child;
|
|
}
|
|
|
|
next_child:
|
|
/* to prevent out of boundary */
|
|
if (++index >= rphy->phy_cfg->num_ports)
|
|
break;
|
|
}
|
|
|
|
provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
|
|
return PTR_ERR_OR_ZERO(provider);
|
|
|
|
put_child:
|
|
of_node_put(child_np);
|
|
disable_clks:
|
|
if (rphy->clk) {
|
|
clk_disable_unprepare(rphy->clk);
|
|
clk_put(rphy->clk);
|
|
}
|
|
return ret;
|
|
}
|
|
|
|
static const struct rockchip_usb2phy_cfg rk3228_phy_cfgs[] = {
|
|
{
|
|
.reg = 0x760,
|
|
.num_ports = 2,
|
|
.clkout_ctl = { 0x0768, 4, 4, 1, 0 },
|
|
.port_cfgs = {
|
|
[USB2PHY_PORT_OTG] = {
|
|
.phy_sus = { 0x0760, 15, 0, 0, 0x1d1 },
|
|
.bvalid_det_en = { 0x0680, 3, 3, 0, 1 },
|
|
.bvalid_det_st = { 0x0690, 3, 3, 0, 1 },
|
|
.bvalid_det_clr = { 0x06a0, 3, 3, 0, 1 },
|
|
.ls_det_en = { 0x0680, 2, 2, 0, 1 },
|
|
.ls_det_st = { 0x0690, 2, 2, 0, 1 },
|
|
.ls_det_clr = { 0x06a0, 2, 2, 0, 1 },
|
|
.utmi_bvalid = { 0x0480, 4, 4, 0, 1 },
|
|
.utmi_ls = { 0x0480, 3, 2, 0, 1 },
|
|
},
|
|
[USB2PHY_PORT_HOST] = {
|
|
.phy_sus = { 0x0764, 15, 0, 0, 0x1d1 },
|
|
.ls_det_en = { 0x0680, 4, 4, 0, 1 },
|
|
.ls_det_st = { 0x0690, 4, 4, 0, 1 },
|
|
.ls_det_clr = { 0x06a0, 4, 4, 0, 1 }
|
|
}
|
|
},
|
|
.chg_det = {
|
|
.opmode = { 0x0760, 3, 0, 5, 1 },
|
|
.cp_det = { 0x0884, 4, 4, 0, 1 },
|
|
.dcp_det = { 0x0884, 3, 3, 0, 1 },
|
|
.dp_det = { 0x0884, 5, 5, 0, 1 },
|
|
.idm_sink_en = { 0x0768, 8, 8, 0, 1 },
|
|
.idp_sink_en = { 0x0768, 7, 7, 0, 1 },
|
|
.idp_src_en = { 0x0768, 9, 9, 0, 1 },
|
|
.rdm_pdwn_en = { 0x0768, 10, 10, 0, 1 },
|
|
.vdm_src_en = { 0x0768, 12, 12, 0, 1 },
|
|
.vdp_src_en = { 0x0768, 11, 11, 0, 1 },
|
|
},
|
|
},
|
|
{
|
|
.reg = 0x800,
|
|
.num_ports = 2,
|
|
.clkout_ctl = { 0x0808, 4, 4, 1, 0 },
|
|
.port_cfgs = {
|
|
[USB2PHY_PORT_OTG] = {
|
|
.phy_sus = { 0x800, 15, 0, 0, 0x1d1 },
|
|
.ls_det_en = { 0x0684, 0, 0, 0, 1 },
|
|
.ls_det_st = { 0x0694, 0, 0, 0, 1 },
|
|
.ls_det_clr = { 0x06a4, 0, 0, 0, 1 }
|
|
},
|
|
[USB2PHY_PORT_HOST] = {
|
|
.phy_sus = { 0x804, 15, 0, 0, 0x1d1 },
|
|
.ls_det_en = { 0x0684, 1, 1, 0, 1 },
|
|
.ls_det_st = { 0x0694, 1, 1, 0, 1 },
|
|
.ls_det_clr = { 0x06a4, 1, 1, 0, 1 }
|
|
}
|
|
},
|
|
},
|
|
{ /* sentinel */ }
|
|
};
|
|
|
|
static const struct rockchip_usb2phy_cfg rk3328_phy_cfgs[] = {
|
|
{
|
|
.reg = 0x100,
|
|
.num_ports = 2,
|
|
.clkout_ctl = { 0x108, 4, 4, 1, 0 },
|
|
.port_cfgs = {
|
|
[USB2PHY_PORT_OTG] = {
|
|
.phy_sus = { 0x0100, 15, 0, 0, 0x1d1 },
|
|
.bvalid_det_en = { 0x0110, 2, 2, 0, 1 },
|
|
.bvalid_det_st = { 0x0114, 2, 2, 0, 1 },
|
|
.bvalid_det_clr = { 0x0118, 2, 2, 0, 1 },
|
|
.ls_det_en = { 0x0110, 0, 0, 0, 1 },
|
|
.ls_det_st = { 0x0114, 0, 0, 0, 1 },
|
|
.ls_det_clr = { 0x0118, 0, 0, 0, 1 },
|
|
.utmi_avalid = { 0x0120, 10, 10, 0, 1 },
|
|
.utmi_bvalid = { 0x0120, 9, 9, 0, 1 },
|
|
.utmi_ls = { 0x0120, 5, 4, 0, 1 },
|
|
},
|
|
[USB2PHY_PORT_HOST] = {
|
|
.phy_sus = { 0x104, 15, 0, 0, 0x1d1 },
|
|
.ls_det_en = { 0x110, 1, 1, 0, 1 },
|
|
.ls_det_st = { 0x114, 1, 1, 0, 1 },
|
|
.ls_det_clr = { 0x118, 1, 1, 0, 1 },
|
|
.utmi_ls = { 0x120, 17, 16, 0, 1 },
|
|
.utmi_hstdet = { 0x120, 19, 19, 0, 1 }
|
|
}
|
|
},
|
|
.chg_det = {
|
|
.opmode = { 0x0100, 3, 0, 5, 1 },
|
|
.cp_det = { 0x0120, 24, 24, 0, 1 },
|
|
.dcp_det = { 0x0120, 23, 23, 0, 1 },
|
|
.dp_det = { 0x0120, 25, 25, 0, 1 },
|
|
.idm_sink_en = { 0x0108, 8, 8, 0, 1 },
|
|
.idp_sink_en = { 0x0108, 7, 7, 0, 1 },
|
|
.idp_src_en = { 0x0108, 9, 9, 0, 1 },
|
|
.rdm_pdwn_en = { 0x0108, 10, 10, 0, 1 },
|
|
.vdm_src_en = { 0x0108, 12, 12, 0, 1 },
|
|
.vdp_src_en = { 0x0108, 11, 11, 0, 1 },
|
|
},
|
|
},
|
|
{ /* sentinel */ }
|
|
};
|
|
|
|
static const struct rockchip_usb2phy_cfg rk3366_phy_cfgs[] = {
|
|
{
|
|
.reg = 0x700,
|
|
.num_ports = 2,
|
|
.clkout_ctl = { 0x0724, 15, 15, 1, 0 },
|
|
.port_cfgs = {
|
|
[USB2PHY_PORT_HOST] = {
|
|
.phy_sus = { 0x0728, 15, 0, 0, 0x1d1 },
|
|
.ls_det_en = { 0x0680, 4, 4, 0, 1 },
|
|
.ls_det_st = { 0x0690, 4, 4, 0, 1 },
|
|
.ls_det_clr = { 0x06a0, 4, 4, 0, 1 },
|
|
.utmi_ls = { 0x049c, 14, 13, 0, 1 },
|
|
.utmi_hstdet = { 0x049c, 12, 12, 0, 1 }
|
|
}
|
|
},
|
|
},
|
|
{ /* sentinel */ }
|
|
};
|
|
|
|
static const struct rockchip_usb2phy_cfg rk3399_phy_cfgs[] = {
|
|
{
|
|
.reg = 0xe450,
|
|
.num_ports = 2,
|
|
.clkout_ctl = { 0xe450, 4, 4, 1, 0 },
|
|
.port_cfgs = {
|
|
[USB2PHY_PORT_OTG] = {
|
|
.phy_sus = { 0xe454, 1, 0, 2, 1 },
|
|
.bvalid_det_en = { 0xe3c0, 3, 3, 0, 1 },
|
|
.bvalid_det_st = { 0xe3e0, 3, 3, 0, 1 },
|
|
.bvalid_det_clr = { 0xe3d0, 3, 3, 0, 1 },
|
|
.utmi_avalid = { 0xe2ac, 7, 7, 0, 1 },
|
|
.utmi_bvalid = { 0xe2ac, 12, 12, 0, 1 },
|
|
},
|
|
[USB2PHY_PORT_HOST] = {
|
|
.phy_sus = { 0xe458, 1, 0, 0x2, 0x1 },
|
|
.ls_det_en = { 0xe3c0, 6, 6, 0, 1 },
|
|
.ls_det_st = { 0xe3e0, 6, 6, 0, 1 },
|
|
.ls_det_clr = { 0xe3d0, 6, 6, 0, 1 },
|
|
.utmi_ls = { 0xe2ac, 22, 21, 0, 1 },
|
|
.utmi_hstdet = { 0xe2ac, 23, 23, 0, 1 }
|
|
}
|
|
},
|
|
.chg_det = {
|
|
.opmode = { 0xe454, 3, 0, 5, 1 },
|
|
.cp_det = { 0xe2ac, 2, 2, 0, 1 },
|
|
.dcp_det = { 0xe2ac, 1, 1, 0, 1 },
|
|
.dp_det = { 0xe2ac, 0, 0, 0, 1 },
|
|
.idm_sink_en = { 0xe450, 8, 8, 0, 1 },
|
|
.idp_sink_en = { 0xe450, 7, 7, 0, 1 },
|
|
.idp_src_en = { 0xe450, 9, 9, 0, 1 },
|
|
.rdm_pdwn_en = { 0xe450, 10, 10, 0, 1 },
|
|
.vdm_src_en = { 0xe450, 12, 12, 0, 1 },
|
|
.vdp_src_en = { 0xe450, 11, 11, 0, 1 },
|
|
},
|
|
},
|
|
{
|
|
.reg = 0xe460,
|
|
.num_ports = 2,
|
|
.clkout_ctl = { 0xe460, 4, 4, 1, 0 },
|
|
.port_cfgs = {
|
|
[USB2PHY_PORT_OTG] = {
|
|
.phy_sus = { 0xe464, 1, 0, 2, 1 },
|
|
.bvalid_det_en = { 0xe3c0, 8, 8, 0, 1 },
|
|
.bvalid_det_st = { 0xe3e0, 8, 8, 0, 1 },
|
|
.bvalid_det_clr = { 0xe3d0, 8, 8, 0, 1 },
|
|
.utmi_avalid = { 0xe2ac, 10, 10, 0, 1 },
|
|
.utmi_bvalid = { 0xe2ac, 16, 16, 0, 1 },
|
|
},
|
|
[USB2PHY_PORT_HOST] = {
|
|
.phy_sus = { 0xe468, 1, 0, 0x2, 0x1 },
|
|
.ls_det_en = { 0xe3c0, 11, 11, 0, 1 },
|
|
.ls_det_st = { 0xe3e0, 11, 11, 0, 1 },
|
|
.ls_det_clr = { 0xe3d0, 11, 11, 0, 1 },
|
|
.utmi_ls = { 0xe2ac, 26, 25, 0, 1 },
|
|
.utmi_hstdet = { 0xe2ac, 27, 27, 0, 1 }
|
|
}
|
|
},
|
|
},
|
|
{ /* sentinel */ }
|
|
};
|
|
|
|
static const struct rockchip_usb2phy_cfg rv1108_phy_cfgs[] = {
|
|
{
|
|
.reg = 0x100,
|
|
.num_ports = 2,
|
|
.clkout_ctl = { 0x108, 4, 4, 1, 0 },
|
|
.port_cfgs = {
|
|
[USB2PHY_PORT_OTG] = {
|
|
.phy_sus = { 0x0100, 15, 0, 0, 0x1d1 },
|
|
.bvalid_det_en = { 0x0680, 3, 3, 0, 1 },
|
|
.bvalid_det_st = { 0x0690, 3, 3, 0, 1 },
|
|
.bvalid_det_clr = { 0x06a0, 3, 3, 0, 1 },
|
|
.ls_det_en = { 0x0680, 2, 2, 0, 1 },
|
|
.ls_det_st = { 0x0690, 2, 2, 0, 1 },
|
|
.ls_det_clr = { 0x06a0, 2, 2, 0, 1 },
|
|
.utmi_bvalid = { 0x0804, 10, 10, 0, 1 },
|
|
.utmi_ls = { 0x0804, 13, 12, 0, 1 },
|
|
},
|
|
[USB2PHY_PORT_HOST] = {
|
|
.phy_sus = { 0x0104, 15, 0, 0, 0x1d1 },
|
|
.ls_det_en = { 0x0680, 4, 4, 0, 1 },
|
|
.ls_det_st = { 0x0690, 4, 4, 0, 1 },
|
|
.ls_det_clr = { 0x06a0, 4, 4, 0, 1 },
|
|
.utmi_ls = { 0x0804, 9, 8, 0, 1 },
|
|
.utmi_hstdet = { 0x0804, 7, 7, 0, 1 }
|
|
}
|
|
},
|
|
.chg_det = {
|
|
.opmode = { 0x0100, 3, 0, 5, 1 },
|
|
.cp_det = { 0x0804, 1, 1, 0, 1 },
|
|
.dcp_det = { 0x0804, 0, 0, 0, 1 },
|
|
.dp_det = { 0x0804, 2, 2, 0, 1 },
|
|
.idm_sink_en = { 0x0108, 8, 8, 0, 1 },
|
|
.idp_sink_en = { 0x0108, 7, 7, 0, 1 },
|
|
.idp_src_en = { 0x0108, 9, 9, 0, 1 },
|
|
.rdm_pdwn_en = { 0x0108, 10, 10, 0, 1 },
|
|
.vdm_src_en = { 0x0108, 12, 12, 0, 1 },
|
|
.vdp_src_en = { 0x0108, 11, 11, 0, 1 },
|
|
},
|
|
},
|
|
{ /* sentinel */ }
|
|
};
|
|
|
|
static const struct of_device_id rockchip_usb2phy_dt_match[] = {
|
|
{ .compatible = "rockchip,rk3228-usb2phy", .data = &rk3228_phy_cfgs },
|
|
{ .compatible = "rockchip,rk3328-usb2phy", .data = &rk3328_phy_cfgs },
|
|
{ .compatible = "rockchip,rk3366-usb2phy", .data = &rk3366_phy_cfgs },
|
|
{ .compatible = "rockchip,rk3399-usb2phy", .data = &rk3399_phy_cfgs },
|
|
{ .compatible = "rockchip,rv1108-usb2phy", .data = &rv1108_phy_cfgs },
|
|
{}
|
|
};
|
|
MODULE_DEVICE_TABLE(of, rockchip_usb2phy_dt_match);
|
|
|
|
static struct platform_driver rockchip_usb2phy_driver = {
|
|
.probe = rockchip_usb2phy_probe,
|
|
.driver = {
|
|
.name = "rockchip-usb2phy",
|
|
.of_match_table = rockchip_usb2phy_dt_match,
|
|
},
|
|
};
|
|
module_platform_driver(rockchip_usb2phy_driver);
|
|
|
|
MODULE_AUTHOR("Frank Wang <frank.wang@rock-chips.com>");
|
|
MODULE_DESCRIPTION("Rockchip USB2.0 PHY driver");
|
|
MODULE_LICENSE("GPL v2");
|