129 lines
3.2 KiB
C
129 lines
3.2 KiB
C
// SPDX-License-Identifier: GPL-2.0-or-later
|
|
/*
|
|
* arch/arm/mach-ep93xx/simone.c
|
|
* Simplemachines Sim.One support.
|
|
*
|
|
* Copyright (C) 2010 Ryan Mallon
|
|
*
|
|
* Based on the 2.6.24.7 support:
|
|
* Copyright (C) 2009 Simplemachines
|
|
* MMC support by Peter Ivanov <ivanovp@gmail.com>, 2007
|
|
*/
|
|
|
|
#include <linux/kernel.h>
|
|
#include <linux/init.h>
|
|
#include <linux/platform_device.h>
|
|
#include <linux/i2c.h>
|
|
#include <linux/mmc/host.h>
|
|
#include <linux/spi/spi.h>
|
|
#include <linux/spi/mmc_spi.h>
|
|
#include <linux/platform_data/video-ep93xx.h>
|
|
#include <linux/platform_data/spi-ep93xx.h>
|
|
#include <linux/gpio.h>
|
|
#include <linux/gpio/machine.h>
|
|
|
|
#include "hardware.h"
|
|
#include "gpio-ep93xx.h"
|
|
|
|
#include <asm/mach-types.h>
|
|
#include <asm/mach/arch.h>
|
|
|
|
#include "soc.h"
|
|
|
|
static struct ep93xx_eth_data __initdata simone_eth_data = {
|
|
.phy_id = 1,
|
|
};
|
|
|
|
static struct ep93xxfb_mach_info __initdata simone_fb_info = {
|
|
.flags = EP93XXFB_USE_SDCSN0 | EP93XXFB_PCLK_FALLING,
|
|
};
|
|
|
|
static struct mmc_spi_platform_data simone_mmc_spi_data = {
|
|
.detect_delay = 500,
|
|
.ocr_mask = MMC_VDD_32_33 | MMC_VDD_33_34,
|
|
};
|
|
|
|
static struct gpiod_lookup_table simone_mmc_spi_gpio_table = {
|
|
.dev_id = "mmc_spi.0", /* "mmc_spi" @ CS0 */
|
|
.table = {
|
|
/* Card detect */
|
|
GPIO_LOOKUP_IDX("A", 0, NULL, 0, GPIO_ACTIVE_LOW),
|
|
{ },
|
|
},
|
|
};
|
|
|
|
static struct spi_board_info simone_spi_devices[] __initdata = {
|
|
{
|
|
.modalias = "mmc_spi",
|
|
.platform_data = &simone_mmc_spi_data,
|
|
/*
|
|
* We use 10 MHz even though the maximum is 3.7 MHz. The driver
|
|
* will limit it automatically to max. frequency.
|
|
*/
|
|
.max_speed_hz = 10 * 1000 * 1000,
|
|
.bus_num = 0,
|
|
.chip_select = 0,
|
|
.mode = SPI_MODE_3,
|
|
},
|
|
};
|
|
|
|
/*
|
|
* Up to v1.3, the Sim.One used SFRMOUT as SD card chip select, but this goes
|
|
* low between multi-message command blocks. From v1.4, it uses a GPIO instead.
|
|
* v1.3 parts will still work, since the signal on SFRMOUT is automatic.
|
|
*/
|
|
static struct gpiod_lookup_table simone_spi_cs_gpio_table = {
|
|
.dev_id = "spi0",
|
|
.table = {
|
|
GPIO_LOOKUP("A", 1, "cs", GPIO_ACTIVE_LOW),
|
|
{ },
|
|
},
|
|
};
|
|
|
|
static struct ep93xx_spi_info simone_spi_info __initdata = {
|
|
.use_dma = 1,
|
|
};
|
|
|
|
static struct i2c_board_info __initdata simone_i2c_board_info[] = {
|
|
{
|
|
I2C_BOARD_INFO("ds1337", 0x68),
|
|
},
|
|
};
|
|
|
|
static struct platform_device simone_audio_device = {
|
|
.name = "simone-audio",
|
|
.id = -1,
|
|
};
|
|
|
|
static void __init simone_register_audio(void)
|
|
{
|
|
ep93xx_register_ac97();
|
|
platform_device_register(&simone_audio_device);
|
|
}
|
|
|
|
static void __init simone_init_machine(void)
|
|
{
|
|
ep93xx_init_devices();
|
|
ep93xx_register_flash(2, EP93XX_CS6_PHYS_BASE, SZ_8M);
|
|
ep93xx_register_eth(&simone_eth_data, 1);
|
|
ep93xx_register_fb(&simone_fb_info);
|
|
ep93xx_register_i2c(simone_i2c_board_info,
|
|
ARRAY_SIZE(simone_i2c_board_info));
|
|
gpiod_add_lookup_table(&simone_mmc_spi_gpio_table);
|
|
gpiod_add_lookup_table(&simone_spi_cs_gpio_table);
|
|
ep93xx_register_spi(&simone_spi_info, simone_spi_devices,
|
|
ARRAY_SIZE(simone_spi_devices));
|
|
simone_register_audio();
|
|
}
|
|
|
|
MACHINE_START(SIM_ONE, "Simplemachines Sim.One Board")
|
|
/* Maintainer: Ryan Mallon */
|
|
.atag_offset = 0x100,
|
|
.map_io = ep93xx_map_io,
|
|
.init_irq = ep93xx_init_irq,
|
|
.init_time = ep93xx_timer_init,
|
|
.init_machine = simone_init_machine,
|
|
.init_late = ep93xx_init_late,
|
|
.restart = ep93xx_restart,
|
|
MACHINE_END
|