192 lines
6.7 KiB
C
192 lines
6.7 KiB
C
/* SPDX-License-Identifier: (GPL-2.0 OR BSD-3-Clause) */
|
|
/*
|
|
* This file is provided under a dual BSD/GPLv2 license. When using or
|
|
* redistributing this file, you may do so under either license.
|
|
*
|
|
* Copyright(c) 2018 Intel Corporation. All rights reserved.
|
|
*/
|
|
|
|
#ifndef __INCLUDE_SOUND_SOF_DAI_INTEL_H__
|
|
#define __INCLUDE_SOUND_SOF_DAI_INTEL_H__
|
|
|
|
#include <sound/sof/header.h>
|
|
|
|
/* ssc1: TINTE */
|
|
#define SOF_DAI_INTEL_SSP_QUIRK_TINTE (1 << 0)
|
|
/* ssc1: PINTE */
|
|
#define SOF_DAI_INTEL_SSP_QUIRK_PINTE (1 << 1)
|
|
/* ssc2: SMTATF */
|
|
#define SOF_DAI_INTEL_SSP_QUIRK_SMTATF (1 << 2)
|
|
/* ssc2: MMRATF */
|
|
#define SOF_DAI_INTEL_SSP_QUIRK_MMRATF (1 << 3)
|
|
/* ssc2: PSPSTWFDFD */
|
|
#define SOF_DAI_INTEL_SSP_QUIRK_PSPSTWFDFD (1 << 4)
|
|
/* ssc2: PSPSRWFDFD */
|
|
#define SOF_DAI_INTEL_SSP_QUIRK_PSPSRWFDFD (1 << 5)
|
|
/* ssc1: LBM */
|
|
#define SOF_DAI_INTEL_SSP_QUIRK_LBM (1 << 6)
|
|
|
|
/* here is the possibility to define others aux macros */
|
|
|
|
#define SOF_DAI_INTEL_SSP_FRAME_PULSE_WIDTH_MAX 38
|
|
#define SOF_DAI_INTEL_SSP_SLOT_PADDING_MAX 31
|
|
|
|
/* SSP clocks control settings
|
|
*
|
|
* Macros for clks_control field in sof_ipc_dai_ssp_params struct.
|
|
*/
|
|
|
|
/* mclk 0 disable */
|
|
#define SOF_DAI_INTEL_SSP_MCLK_0_DISABLE BIT(0)
|
|
/* mclk 1 disable */
|
|
#define SOF_DAI_INTEL_SSP_MCLK_1_DISABLE BIT(1)
|
|
/* mclk keep active */
|
|
#define SOF_DAI_INTEL_SSP_CLKCTRL_MCLK_KA BIT(2)
|
|
/* bclk keep active */
|
|
#define SOF_DAI_INTEL_SSP_CLKCTRL_BCLK_KA BIT(3)
|
|
/* fs keep active */
|
|
#define SOF_DAI_INTEL_SSP_CLKCTRL_FS_KA BIT(4)
|
|
/* bclk idle */
|
|
#define SOF_DAI_INTEL_SSP_CLKCTRL_BCLK_IDLE_HIGH BIT(5)
|
|
|
|
/* SSP Configuration Request - SOF_IPC_DAI_SSP_CONFIG */
|
|
struct sof_ipc_dai_ssp_params {
|
|
struct sof_ipc_hdr hdr;
|
|
uint16_t reserved1;
|
|
uint16_t mclk_id;
|
|
|
|
uint32_t mclk_rate; /* mclk frequency in Hz */
|
|
uint32_t fsync_rate; /* fsync frequency in Hz */
|
|
uint32_t bclk_rate; /* bclk frequency in Hz */
|
|
|
|
/* TDM */
|
|
uint32_t tdm_slots;
|
|
uint32_t rx_slots;
|
|
uint32_t tx_slots;
|
|
|
|
/* data */
|
|
uint32_t sample_valid_bits;
|
|
uint16_t tdm_slot_width;
|
|
uint16_t reserved2; /* alignment */
|
|
|
|
/* MCLK */
|
|
uint32_t mclk_direction;
|
|
|
|
uint16_t frame_pulse_width;
|
|
uint16_t tdm_per_slot_padding_flag;
|
|
uint32_t clks_control;
|
|
uint32_t quirks;
|
|
uint32_t bclk_delay; /* guaranteed time (ms) for which BCLK
|
|
* will be driven, before sending data
|
|
*/
|
|
} __packed;
|
|
|
|
/* HDA Configuration Request - SOF_IPC_DAI_HDA_CONFIG */
|
|
struct sof_ipc_dai_hda_params {
|
|
struct sof_ipc_hdr hdr;
|
|
uint32_t link_dma_ch;
|
|
} __packed;
|
|
|
|
/* DMIC Configuration Request - SOF_IPC_DAI_DMIC_CONFIG */
|
|
|
|
/* This struct is defined per 2ch PDM controller available in the platform.
|
|
* Normally it is sufficient to set the used microphone specific enables to 1
|
|
* and keep other parameters as zero. The customizations are:
|
|
*
|
|
* 1. If a device mixes different microphones types with different polarity
|
|
* and/or the absolute polarity matters the PCM signal from a microphone
|
|
* can be inverted with the controls.
|
|
*
|
|
* 2. If the microphones in a stereo pair do not appear in captured stream
|
|
* in desired order due to board schematics choises they can be swapped with
|
|
* the clk_edge parameter.
|
|
*
|
|
* 3. If PDM bit errors are seen in capture (poor quality) the skew parameter
|
|
* that delays the sampling time of data by half cycles of DMIC source clock
|
|
* can be tried for improvement. However there is no guarantee for this to fix
|
|
* data integrity problems.
|
|
*/
|
|
struct sof_ipc_dai_dmic_pdm_ctrl {
|
|
struct sof_ipc_hdr hdr;
|
|
uint16_t id; /**< PDM controller ID */
|
|
|
|
uint16_t enable_mic_a; /**< Use A (left) channel mic (0 or 1)*/
|
|
uint16_t enable_mic_b; /**< Use B (right) channel mic (0 or 1)*/
|
|
|
|
uint16_t polarity_mic_a; /**< Optionally invert mic A signal (0 or 1) */
|
|
uint16_t polarity_mic_b; /**< Optionally invert mic B signal (0 or 1) */
|
|
|
|
uint16_t clk_edge; /**< Optionally swap data clock edge (0 or 1) */
|
|
uint16_t skew; /**< Adjust PDM data sampling vs. clock (0..15) */
|
|
|
|
uint16_t reserved[3]; /**< Make sure the total size is 4 bytes aligned */
|
|
} __packed;
|
|
|
|
/* This struct contains the global settings for all 2ch PDM controllers. The
|
|
* version number used in configuration data is checked vs. version used by
|
|
* device driver src/drivers/dmic.c need to match. It is incremented from
|
|
* initial value 1 if updates done for the to driver would alter the operation
|
|
* of the microhone.
|
|
*
|
|
* Note: The microphone clock (pdmclk_min, pdmclk_max, duty_min, duty_max)
|
|
* parameters need to be set as defined in microphone data sheet. E.g. clock
|
|
* range 1.0 - 3.2 MHz is usually supported microphones. Some microphones are
|
|
* multi-mode capable and there may be denied mic clock frequencies between
|
|
* the modes. In such case set the clock range limits of the desired mode to
|
|
* avoid the driver to set clock to an illegal rate.
|
|
*
|
|
* The duty cycle could be set to 48-52% if not known. Generally these
|
|
* parameters can be altered within data sheet specified limits to match
|
|
* required audio application performance power.
|
|
*
|
|
* The microphone clock needs to be usually about 50-80 times the used audio
|
|
* sample rate. With highest sample rates above 48 kHz this can relaxed
|
|
* somewhat.
|
|
*
|
|
* The parameter wake_up_time describes how long time the microphone needs
|
|
* for the data line to produce valid output from mic clock start. The driver
|
|
* will mute the captured audio for the given time. The min_clock_on_time
|
|
* parameter is used to prevent too short clock bursts to happen. The driver
|
|
* will keep the clock active after capture stop if this time is not yet
|
|
* met. The unit for both is microseconds (us). Exceed of 100 ms will be
|
|
* treated as an error.
|
|
*/
|
|
struct sof_ipc_dai_dmic_params {
|
|
struct sof_ipc_hdr hdr;
|
|
uint32_t driver_ipc_version; /**< Version (1..N) */
|
|
|
|
uint32_t pdmclk_min; /**< Minimum microphone clock in Hz (100000..N) */
|
|
uint32_t pdmclk_max; /**< Maximum microphone clock in Hz (min...N) */
|
|
|
|
uint32_t fifo_fs; /**< FIFO sample rate in Hz (8000..96000) */
|
|
uint32_t reserved_1; /**< Reserved */
|
|
uint16_t fifo_bits; /**< FIFO word length (16 or 32) */
|
|
uint16_t reserved_2; /**< Reserved */
|
|
|
|
uint16_t duty_min; /**< Min. mic clock duty cycle in % (20..80) */
|
|
uint16_t duty_max; /**< Max. mic clock duty cycle in % (min..80) */
|
|
|
|
uint32_t num_pdm_active; /**< Number of active pdm controllers */
|
|
|
|
uint32_t wake_up_time; /**< Time from clock start to data (us) */
|
|
uint32_t min_clock_on_time; /**< Min. time that clk is kept on (us) */
|
|
uint32_t unmute_ramp_time; /**< Length of logarithmic gain ramp (ms) */
|
|
|
|
/* reserved for future use */
|
|
uint32_t reserved[5];
|
|
|
|
/**< variable number of pdm controller config */
|
|
struct sof_ipc_dai_dmic_pdm_ctrl pdm[0];
|
|
} __packed;
|
|
|
|
/* ALH Configuration Request - SOF_IPC_DAI_ALH_CONFIG */
|
|
struct sof_ipc_dai_alh_params {
|
|
struct sof_ipc_hdr hdr;
|
|
uint32_t stream_id;
|
|
|
|
/* reserved for future use */
|
|
uint32_t reserved[15];
|
|
} __packed;
|
|
|
|
#endif
|