Gitee limit the repo's size to 3GB, to reduce the size of the code,
sync codes to ock 5.4.119-20.0009.21 in one commit.
Signed-off-by: Jianping Liu <frankjpliu@tencent.com>
Sync kernel codes to the same with 590eaf1fec ("Init Repo base on
linux 5.4.32 long term, and add base tlinux kernel interfaces."), which
is from tk4, and it is the base of tk4.
Signed-off-by: Jianping Liu <frankjpliu@tencent.com>
There are a few core fixes here around error handling and handling if
suspend mode configuration and some driver specific fixes here but the
most important change is the fix to the fixed-regulator DT schema
conversion introduced during the last merge window. That fixes one of
the last two errors preventing successful execution of "make dt_binding_check"
which will be enourmously helpful for DT schema development.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAl2wgdsTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0PxRB/4uqIJR3n3mIdrHtB0DVaZEWm7jsC6L
PUYZZH//EkLe6d5hgb2qKYrpIJIlKdrVukySl/uyE//gxNH6BUOgggfAGx5qIAjN
qGB6dv+M+AWiDW3hRkMPQ/RnnNgm/llM5cOIHjFqHvYiVbfppIYkKFoCMS8BPWDT
8DUlSwRTGHDKlR1Zn7+HJqvE+eoDAgTVnwoDKaZUh6sL2UrNA8nf0irsB6yq1n+u
1O9D02oTd01tw8Qy3/zAdL+E1RfHbYAuobz367mRUaEzZg6AFG3eWkuJdGIYR+14
C5ypBi/e0zXOyWHEjA5qfxXNbw0U+j4R37iPdgvQvhVQp7D8gIPqXIxX
=r41P
-----END PGP SIGNATURE-----
Merge tag 'regulator-fix-v5.4-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"There are a few core fixes here around error handling and handling if
suspend mode configuration and some driver specific fixes here but the
most important change is the fix to the fixed-regulator DT schema
conversion introduced during the last merge window.
That fixes one of the last two errors preventing successful execution
of "make dt_binding_check" which will be enormously helpful for DT
schema development"
* tag 'regulator-fix-v5.4-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: qcom-rpmh: Fix PMIC5 BoB min voltage
regulator: pfuze100-regulator: Variable "val" in pfuze100_regulator_probe() could be uninitialized
regulator: lochnagar: Add on_off_delay for VDDCORE
regulator: ti-abb: Fix timeout in ti_abb_wait_txdone/ti_abb_clear_all_txdone
regulator: da9062: fix suspend_enable/disable preparation
dt-bindings: fixed-regulator: fix compatible enum
regulator: fixed: Prevent NULL pointer dereference when !CONFIG_OF
regulator: core: make regulator_register() EPROBE_DEFER aware
regulator: of: fix suspend-min/max-voltage parsing
In function pfuze100_regulator_probe(), variable "val" could be
initialized if regmap_read() fails. However, "val" is used to
decide the control flow later in the if statement, which is
potentially unsafe.
Signed-off-by: Yizhuo <yzhai003@ucr.edu>
Link: https://lore.kernel.org/r/20190929170957.14775-1-yzhai003@ucr.edu
Signed-off-by: Mark Brown <broonie@kernel.org>
The VDDCORE regulator takes a good length of time to discharge down, so
add an on_off_delay to ensure DCVDD is removed before it is powered on
again.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20191001132017.1785-1-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
ti_abb_wait_txdone() may return -ETIMEDOUT when ti_abb_check_txdone()
returns true in the latest iteration of the while loop because the timeout
value is abb->settling_time + 1. Similarly, ti_abb_clear_all_txdone() may
return -ETIMEDOUT when ti_abb_check_txdone() returns false in the latest
iteration of the while loop. Fix it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20190929095848.21960-1-axel.lin@ingics.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently the suspend reg_field maps to the pmic voltage selection bits
and is used during suspend_enabe/disable() and during get_mode(). This
seems to be wrong for both use cases.
Use case one (suspend_enabe/disable):
Those callbacks are used to mark a regulator device as enabled/disabled
during suspend. Marking the regulator enabled during suspend is done by
the LDOx_CONF/BUCKx_CONF bit within the LDOx_CONT/BUCKx_CONT registers.
Setting this bit tells the DA9062 PMIC state machine to keep the
regulator on in POWERDOWN mode and switch to suspend voltage.
Use case two (get_mode):
The get_mode callback is used to retrieve the active mode state. Since
the regulator-setting-A is used for the active state and
regulator-setting-B for the suspend state there is no need to check
which regulator setting is active.
Fixes: 4068e5182a ("regulator: da9062: DA9062 regulator driver")
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Link: https://lore.kernel.org/r/20190917124246.11732-2-m.felsch@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Use of_device_get_match_data which has NULL test for match before
dereference match->data. Add NULL test for drvtype so it still works
for fixed_voltage_ops when !CONFIG_OF.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Philippe Schenker <philippe.schenker@toradex.com>
Link: https://lore.kernel.org/r/20190922022928.28355-1-axel.lin@ingics.com
Signed-off-by: Mark Brown <broonie@kernel.org>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQUwxxKyE5l/npt8ARiEGxRG/Sl2wUCXYAIeQAKCRBiEGxRG/Sl
2/SzAQDEnoNxzV/R5kWFd+2kmFeY3cll0d99KMrWJ8om+kje6QD/cXxZHzFm+T1L
UPF66k76oOODV7cyndjXnTnRXbeCRAM=
=Szby
-----END PGP SIGNATURE-----
Merge tag 'leds-for-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds
Pull LED updates from Jacek Anaszewski:
"In this cycle we've finally managed to contribute the patch set
sorting out LED naming issues. Besides that there are many changes
scattered among various LED class drivers and triggers.
LED naming related improvements:
- add new 'function' and 'color' fwnode properties and deprecate
'label' property which has been frequently abused for conveying
vendor specific names that have been available in sysfs anyway
- introduce a set of standard LED_FUNCTION* definitions
- introduce a set of standard LED_COLOR_ID* definitions
- add a new {devm_}led_classdev_register_ext() API with the
capability of automatic LED name composition basing on the
properties available in the passed fwnode; the function is
backwards compatible in a sense that it uses 'label' data, if
present in the fwnode, for creating LED name
- add tools/leds/get_led_device_info.sh script for retrieving LED
vendor, product and bus names, if applicable; it also performs
basic validation of an LED name
- update following drivers and their DT bindings to use the new LED
registration API:
- leds-an30259a, leds-gpio, leds-as3645a, leds-aat1290, leds-cr0014114,
leds-lm3601x, leds-lm3692x, leds-lp8860, leds-lt3593, leds-sc27xx-blt
Other LED class improvements:
- replace {devm_}led_classdev_register() macros with inlines
- allow to call led_classdev_unregister() unconditionally
- switch to use fwnode instead of be stuck with OF one
LED triggers improvements:
- led-triggers:
- fix dereferencing of null pointer
- fix a memory leak bug
- ledtrig-gpio:
- GPIO 0 is valid
Drop superseeded apu2/3 support from leds-apu since for apu2+ a newer,
more complete driver exists, based on a generic driver for the AMD
SOCs gpio-controller, supporting LEDs as well other devices:
- drop profile field from priv data
- drop iosize field from priv data
- drop enum_apu_led_platform_types
- drop superseeded apu2/3 led support
- add pr_fmt prefix for better log output
- fix error message on probing failure
Other misc fixes and improvements to existing LED class drivers:
- leds-ns2, leds-max77650:
- add of_node_put() before return
- leds-pwm, leds-is31fl32xx:
- use struct_size() helper
- leds-lm3697, leds-lm36274, leds-lm3532:
- switch to use fwnode_property_count_uXX()
- leds-lm3532:
- fix brightness control for i2c mode
- change the define for the fs current register
- fixes for the driver for stability
- add full scale current configuration
- dt: Add property for full scale current.
- avoid potentially unpaired regulator calls
- move static keyword to the front of declarations
- fix optional led-max-microamp prop error handling
- leds-max77650:
- add of_node_put() before return
- add MODULE_ALIAS()
- Switch to fwnode property API
- leds-as3645a:
- fix misuse of strlcpy
- leds-netxbig:
- add of_node_put() in netxbig_leds_get_of_pdata()
- remove legacy board-file support
- leds-is31fl319x:
- simplify getting the adapter of a client
- leds-ti-lmu-common:
- fix coccinelle issue
- move static keyword to the front of declaration
- leds-syscon:
- use resource managed variant of device register
- leds-ktd2692:
- fix a typo in the name of a constant
- leds-lp5562:
- allow firmware files up to the maximum length
- leds-an30259a:
- fix typo
- leds-pca953x:
- include the right header"
* tag 'leds-for-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds: (72 commits)
leds: lm3532: Fix optional led-max-microamp prop error handling
led: triggers: Fix dereferencing of null pointer
leds: ti-lmu-common: Move static keyword to the front of declaration
leds: lm3532: Move static keyword to the front of declarations
leds: trigger: gpio: GPIO 0 is valid
leds: pwm: Use struct_size() helper
leds: is31fl32xx: Use struct_size() helper
leds: ti-lmu-common: Fix coccinelle issue in TI LMU
leds: lm3532: Avoid potentially unpaired regulator calls
leds: syscon: Use resource managed variant of device register
leds: Replace {devm_}led_classdev_register() macros with inlines
leds: Allow to call led_classdev_unregister() unconditionally
leds: lm3532: Add full scale current configuration
dt: lm3532: Add property for full scale current.
leds: lm3532: Fixes for the driver for stability
leds: lm3532: Change the define for the fs current register
leds: lm3532: Fix brightness control for i2c mode
leds: Switch to use fwnode instead of be stuck with OF one
leds: max77650: Switch to fwnode property API
led: triggers: Fix a memory leak bug
...
Sometimes it can happen that the regulator_of_get_init_data() can't
retrieve the config due to a not probed device the regulator depends on.
Fix that by checking the return value of of_parse_cb() and return
EPROBE_DEFER in such cases.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Link: https://lore.kernel.org/r/20190917154021.14693-4-m.felsch@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently the regulator-suspend-min/max-microvolt must be within the
root regulator node but the dt-bindings specifies it as subnode
properties for the regulator-state-[mem/disk/standby] node. The only DT
using this bindings currently is the at91-sama5d2_xplained.dts and this
DT uses it correctly. I don't know if it isn't tested but it can't work
without this fix.
Fixes: f7efad10b5 ("regulator: add PM suspend and resume hooks")
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Link: https://lore.kernel.org/r/20190917154021.14693-3-m.felsch@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
regulator_uV_show() is missing error handling if regulator_get_voltage_rdev()
returns negative values. Instead it prints the errno as a string, e.g. -EINVAL
as "-22" which could be interpreted as -22 µV.
We also do not need to hold the lock while converting the integer to a string.
Reported-by: Adam Ford <aford173@gmail.com>
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Tested-by: Adam Ford <aford173@gmail.com>
Link: https://lore.kernel.org/r/f37f2a1276efcb34cf3b7f1a25481175be048806.1568143348.git.hns@goldelico.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This fixes 11da04af0d, as devm_gpiod_get_from_of_node() does
not do translation "con-id" -> "con-id-gpios" that our bindings expects,
and therefore it was wrong to change connection ID to be simply "enable"
when moving to using devm_gpiod_get_from_of_node().
Fixes: 11da04af0d ("regulator: da9211: Pass descriptors instead of GPIO numbers")
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Link: https://lore.kernel.org/r/20190910170246.GA56792@dtor-ws
Signed-off-by: Mark Brown <broonie@kernel.org>
This fixes 96392c3d8c, as devm_gpiod_get_from_of_node() does
not do translation "con-id" -> "con-id-gpios" that our bindings expects,
and therefore it was wrong to change connection ID to be simply
"maxim,ena" when moving to using devm_gpiod_get_from_of_node().
Fixes: 96392c3d8c ("regulator: max77686: Pass descriptor instead of GPIO number")
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Link: https://lore.kernel.org/r/20190910170050.GA55530@dtor-ws
Signed-off-by: Mark Brown <broonie@kernel.org>
This commit adds the possibility to choose the compatible
"regulator-fixed-clock" in devicetree.
This is a special regulator-fixed that has to have a clock, from which
the regulator gets switched on and off.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Link: https://lore.kernel.org/r/20190910062103.39641-2-philippe.schenker@toradex.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The value under 's2mps11->ext_control_gpiod[i]' is assigned to local
variable and used in probe in one place before. Use it consistently
later so code will be easier to read.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20190909155723.24734-1-krzk@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Use rdev->regmap/&rdev->dev instead of lp87565->regmap/lp87565->dev.
In additional, the lp87565->dev actually is the parent mfd device,
so the dev_err message is misleading here with lp87565->dev.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Link: https://lore.kernel.org/r/20190908035720.17748-1-axel.lin@ingics.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The CS GPIO line is clearly optional GPIO (and marked as such in the
binding document) and we should handle it accordingly. The current code
treats all errors as meaning that there is no GPIO defined, which is
wrong, as it does not handle deferrals raised by the underlying code
properly, nor does it recognize non-existing GPIO from any other
initialization error.
As far as I can see the only reason the driver, unlike all others,
is using OF-specific devm_gpiod_get_from_of_node() so that it can
assign a custom label to the selected GPIO line. Given that noone else
needs that, it should not be doing that either.
Let's switch to using more appropriate devm_gpiod_get_optional().
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Link: https://lore.kernel.org/r/20190904214200.GA66118@dtor-ws
Signed-off-by: Mark Brown <broonie@kernel.org>
Don't populate the array en_mask on the stack but instead make it
static const. Makes the object code smaller by 87 bytes.
Before:
text data bss dec hex filename
12967 3408 0 16375 3ff7 drivers/regulator/lp8788-ldo.o
After:
text data bss dec hex filename
12816 3472 0 16288 3fa0 drivers/regulator/lp8788-ldo.o
(gcc version 9.2.1, amd64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20190906130632.6709-1-colin.king@canonical.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In case of a missing (optional) gpio don't fall through up to
"ti,active-discharge-time-us" due to
devm_fwnode_get_index_gpiod_from_child() returning NULL (since
gpiod_get_from_of_node() returned NULL) but rather indicate success as
intended.
This makes the driver probe correctly when e.g. only the enable gpio is
given.
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Link: https://lore.kernel.org/r/363bd50cc7c60daa57d614a341d1fd649f05194c.1567625660.git.agx@sigxcpu.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The kernel has no way of knowing when we have finished instantiating
drivers, between deferred probe and systems that build key drivers as
modules we might be doing this long after userspace has booted. This has
always been a bit of an issue with regulator_init_complete since it can
power off hardware that's not had it's driver loaded which can result in
user visible effects, the main case is powering off displays. Practically
speaking it's not been an issue in real systems since most systems that
use the regulator API are embedded and build in key drivers anyway but
with Arm laptops coming on the market it's becoming more of an issue so
let's do something about it.
In the absence of any better idea just defer the powering off for 30s
after late_initcall(), this is obviously a hack but it should mask the
issue for now and it's no more arbitrary than late_initcall() itself.
Ideally we'd have some heuristics to detect if we're on an affected
system and tune or skip the delay appropriately, and there may be some
need for a command line option to be added.
Link: https://lore.kernel.org/r/20190904124250.25844-1-broonie@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Tested-by: Lee Jones <lee.jones@linaro.org>
Cc: stable@vger.kernel.org
There are many regulator consumers who - before using the regulator
bulk functions - set the supply names in regulator_bulk_data using
a for loop.
Let's provide a simple helper in the consumer API that allows users
to do the same with a single function call.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Link: https://lore.kernel.org/r/20190830071740.4267-2-brgl@bgdev.pl
Signed-off-by: Mark Brown <broonie@kernel.org>
The mt6358 driver was merged in error, it depends on an existing MFD
rather than a newly added one and needs updates to that driver. Disable
the build until those are merged.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Mark Brown <broonie@kernel.org>
The MT6358 is a regulator found on boards based on MediaTek MT8183 and
probably other SoCs. It is a so called pmic and connects as a slave to
SoC using SPI, wrapped inside the pmic-wrapper.
Signed-off-by: Hsin-Hsiung Wang <hsin-hsiung.wang@mediatek.com>
Link: https://lore.kernel.org/r/1566531931-9772-8-git-send-email-hsin-hsiung.wang@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The differences between SY8824C and SY20278 are different regs
for mode/enable.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Link: https://lore.kernel.org/r/20190827163830.2c94f29b@xhacker.debian
Signed-off-by: Mark Brown <broonie@kernel.org>
The differences between SY8824C and SY20276 are different vsel_min,
vsel_step, vsel_count and regs for mode/enable.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Link: https://lore.kernel.org/r/20190827163721.1947f7a0@xhacker.debian
Signed-off-by: Mark Brown <broonie@kernel.org>
SY8824C is an I2C attached single output regulator made by Silergy Corp,
which is used on several Synaptics berlin platforms to control the
power supply of the ARM cores.
Add a driver for it.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Link: https://lore.kernel.org/r/20190827163418.1a32fc48@xhacker.debian
Signed-off-by: Mark Brown <broonie@kernel.org>
In function of_get_child_regulator(), the loop for_each_child_of_node()
contains two mid-loop return statements, each preceded by a statement
putting child. In order to reduce this repetition, create a new label,
err_node_put, that puts child and then returns the required value;
edit the mid-loop return blocks to instead go to this new label.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Link: https://lore.kernel.org/r/20190815053704.32156-1-nishkadg.linux@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Variable ret is initialized to a value that is never read before
a return statement and hence can be removed. Remove it.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20190813133114.14931-1-colin.king@canonical.com
Signed-off-by: Mark Brown <broonie@kernel.org>
_opp_supported_by_regulators() wrongly ignored errors from
regulator_is_supported_voltage(), so it considered errors as
success. Since
commit 4982094451 ("regulator: core: simplify return value on suported_voltage")
regulator_is_supported_voltage() returns a real boolean, so
errors make _opp_supported_by_regulators() return false.
That reveals a problem with the declaration of the VDD1/2
regulators on twl4030.
The VDD1/VDD2 regulators on twl4030 are neither defined with
voltage lists nor with the continuous flag set, so
regulator_is_supported_voltage() returns false and an error
before above mentioned commit (which was considered success)
The result is that after the above mentioned commit cpufreq
does not work properly e.g. dm3730.
[ 2.490997] core: _opp_supported_by_regulators: OPP minuV: 1012500 maxuV: 1012500, not supported by regulator
[ 2.501617] cpu cpu0: _opp_add: OPP not supported by regulators (300000000)
[ 2.509246] core: _opp_supported_by_regulators: OPP minuV: 1200000 maxuV: 1200000, not supported by regulator
[ 2.519775] cpu cpu0: _opp_add: OPP not supported by regulators (600000000)
[ 2.527313] core: _opp_supported_by_regulators: OPP minuV: 1325000 maxuV: 1325000, not supported by regulator
[ 2.537750] cpu cpu0: _opp_add: OPP not supported by regulators (800000000)
The patch fixes declaration of VDD1/2 regulators by
adding proper voltage lists.
Fixes: 4982094451 ("regulator: core: simplify return value on suported_voltage")
Cc: stable@vger.kernel.org
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Tested-by: Adam Ford <aford173@gmail.com> #logicpd-torpedo-37xx-devkit
Link: https://lore.kernel.org/r/20190814214319.24087-1-andreas@kemnade.info
Signed-off-by: Mark Brown <broonie@kernel.org>
During reset the VMMC regulator doesn't reach 0V and only drops to
1.8V, furthermore the pulse width is under 200us whereas the SD
specification expect 1ms.
The WR_S bit allows the TWL6030 to no reset at all the VMMC during warm
reset and keep the current voltage. Thanks to this workaround the SD
card doesn't reach a undefined reset stage.
Actually this behavior is available for all the LDO regulator, so the
driver will also allow to use it with any of these regulator.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Link: https://lore.kernel.org/r/20190725094542.16547-4-gregory.clement@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
It helps to keep sorted order for compatibles, so sort them
Suggested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20190809073616.1235-2-vkoul@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Building without CONFIG_POWER_SUPPLY will fail:
drivers/regulator/act8865-regulator.o: In function `act8865_pmic_probe':
act8865-regulator.c:(.text+0x357): undefined reference to `devm_power_supply_register'
drivers/regulator/act8865-regulator.o: In function `act8600_charger_get_property':
act8865-regulator.c:(.text+0x3f1): undefined reference to `power_supply_get_drvdata'
Add POWER_SUPPLY dependency to Kconfig.
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: 2d09a79bf6 ("regulator: act8865: Add support for act8600 charger")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20190807133822.67124-1-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The devm_gpiod_get_from_of_node() function never returns NULL, it
returns error pointers on error.
Fixes: a867bde3dd ("regulator: slg51000: add slg51000 regulator driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20190808103335.GD30506@mwanda
Signed-off-by: Mark Brown <broonie@kernel.org>
Each iteration of for_each_child_of_node puts the previous node, but in
the case of a return from the middle of the loop, there is no put, thus
causing a memory leak. Hence add an of_node_put before the return in
two places.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Link: https://lore.kernel.org/r/20190804162023.5673-1-nishkadg.linux@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
We don't need dev_err() messages when platform_get_irq() fails now that
platform_get_irq() prints an error message itself when something goes
wrong. Let's remove these prints with a simple semantic patch.
// <smpl>
@@
expression ret;
struct platform_device *E;
@@
ret =
(
platform_get_irq(E, ...)
|
platform_get_irq_byname(E, ...)
);
if ( \( ret < 0 \| ret <= 0 \) )
{
(
-if (ret != -EPROBE_DEFER)
-{ ...
-dev_err(...);
-... }
|
...
-dev_err(...);
)
...
}
// </smpl>
While we're here, remove braces on if statements that only have one
statement (manually).
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20190730181557.90391-38-swboyd@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The local variable search in regulator_of_get_init_node takes the value
returned by either of_get_child_by_name or of_node_get, both of which
get a node. If this node is not put before returning, it could cause a
memory leak. Hence put search before a mid-loop return statement.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Link: https://lore.kernel.org/r/20190724083231.10276-1-nishkadg.linux@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Jianping Liu