There are lots of ZTE USB id's currently not covered by usb/serial. Adds them,
to allow those devices to work properly on Linux.
While here, put the USB ID's for 0x2002/0x2003 at the sorted order.
This patch is based on zte.c file found on MF645.
PS.: The ZTE driver is commenting the USB ID for 0x0053. It also adds, commented,
an USB ID for 0x0026.
Not sure why, but I think that 0053 is used by their devices in storage mode only.
So, I opted to keep the comment on this patch.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Unfortunately some of the hardware PID belonging to auto-install CDROM
(AICD) of Novatel modems found their way into the option module. This
causes the AICD to be treated as a modem in stead of a disk. Since the
modem ports do not appear until after the AICD is ejected, this
essentially disables the modem. After a couple of minutes the AICD
should auto-eject, but it is just too long a wait. The frequency of the
failure seems to depend on both the hardware and the linux distribution.
Here is a patch that fixes this up, and also adds a couple of new PID,
offering some explanations and removing some incomplete and unnecessary
comments.
Signed-off-by: Dirk De Schepper <ddeschepper@nvtl.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds the product IDs of Huawei's K3765 and K4505 mobile
broadband usb modems to option.c. It also adds a quirk to the option
probe function so that binding to the device's network interface(class
0xff) is avoided. This is necessary to allow another driver to bind to
that, and to avoid programs like wvdial opening a nonfunctioning tty
during modem discovery.
Signed-off-by: Andrew Bird <ajb@spheresystems.co.uk>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The patch adds Huawei ETS 1220 product id into the list of supported
devices in 'option' usb serial driver.
Signed-off-by: Pavel Kazlou <p.i.kazlou@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
AMOI_VENDOR_ID is defined twice. Remove the duplicate entry and move
the AMOI_PRODUCT_9508 definition to be grouped with the other AMOI
product definitions.
Originally-by: Ben Collins <ben.collins@ubuntu.com>
Signed-off-by: Leann Ogasawara <leann.ogasawara@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
usbserial: Add AMOI Skypephone S2 support.
This patch adds support for the AMOI Skypephone S2 to the usbserial module.
Tested-by: Dennis Jansen <Dennis.Jansen@web.de>
Signed-off-by: Dennis Jansen <Dennis.Jansen@web.de>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds support for an olivetti olicard100 HЅDPA usb-stick.
This device is a zeroCD one with ID 0b3c:c700 that needs switching via
eject or usb-modeswitch with
MessageContent="5553424312345678000000000000061b000000030000000000000000000000".
After switching it has ID 0b3c:c000 and provides 5 serial ports ttyUSB[0-4].
Port 0 (modem) and 4 are interrupt ports.
Signed-off-by: Nils Radtke <lkml@Think-Future.de>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
As this code was simply factored out of option, this is a simple
conversion.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
All unsuccessful (non-zero status) URBs were being dropped. After N_IN_URBs are
dropped you will no longer be able to receive data.
This patch resubmits unsuccessful URBs unless the status indicates that it should
be terminated. The statuses that indicate the URB should be terminated was
gathered from other similar drivers.
Signed-off-by: James Maki <jamescmaki@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
PATCH TO EXTEND SUPPORT TO AC8710 WITH 0xFFFF Product ID.
Signed-off-by: Mahesh Kuruganti <maheshkuruganti@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Based on the information provided for by Paweł Drobek, add
a second vendor ID and the correct product ID for ZTE MF 330.
Reported-by: Paweł Drobek <pawel.drobek@gmail.com>
Signed-off: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
I found a DLink DWM 652 U5 USB 3G modem has product ID 0xce1e instead
of orignal 0xce16. The new ID is added.
And I found there are two entries for 0xce16, one has raw number, the
other has symbol DLINK_PRODUCT_DWM_652_U5. This is fixed too.
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Longcheer is a Chinese company that manufactures the devices which a
bunch of different companies like Alcatel, 4G Systems, and Mobidata
rebrand. While I can't find Longcheer's USB ID registered anywhere,
it's pretty clear the ID is theirs.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1344) removes references to port->port.count from the
USB serial drivers. Now that serial ports are properly reference
counted, port.count checking is unnecessary and incorrect. Drivers
should assume that the port is in use from the time the open method
runs until the close method is called.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We have lots of callers that do not need to do this in the first place.
Remove the calls as they both cost CPU and for big buffers can mess up the
multi-page allocation avoidance.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The 4G XS Stick W14 seems to not understand RTS/DTR setting in
option_send_setup causing long timeouts on any open() which disturbs a
lot of well-known userspace applications like minicom or ModemManager.
Therefore, we enable OPTION_BLACKLIST_SENDSETUP blacklisting for it.
Signed-off-by: Gernot Hillier <gernot@hillier.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
As suggested by Matthias Urlichs, this patch adds a somehow generic
mechanism for special handling of devices which don't support all bits
expected by this driver.
The blacklisting code is heavily stolen from sierra.c, but extended to
support different special cases.
For now, one case is implemented (OPTION_BLACKLIST_SENDSETUP), targeted
at the 4G W14 device: devices which don't understand the setting of
RTS/DTR in option_send_setup() causing a USB timeout of 5 s in any
userspace open() which leads to errors in most userspace applications.
In addition, I prepared another case for devices with interfaces which
shall not be accessed by this driver (targeted at the D-Link DWM 652).
However, OPTION_BLACKLIST_RESERVED_IF is not fully implemented yet as I
have no device to test this. Anyone volunteering to help here? If not,
I'll contact the guys who added D-Link DWM 652 support soon.
Signed-off-by: Gernot Hillier <gernot@hillier.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Carsten Juttner thankfully investigated a bit and found out some details
about the chipset used in the 4G W14 device I recently added to
option.c.
I think this information is useful for reference, so I'd be happy if you
could include those bits.
Signed-off-by: Gernot Hillier <gernot@hillier.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The id_table field of the struct usb_device_id is constant in <linux/usb.h>
so it is worth to make the initialization data also constant.
The semantic match that finds this kind of pattern is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r@
disable decl_init,const_decl_init;
identifier I1, I2, x;
@@
struct I1 {
...
const struct I2 *x;
...
};
@s@
identifier r.I1, y;
identifier r.x, E;
@@
struct I1 y = {
.x = E,
};
@c@
identifier r.I2;
identifier s.E;
@@
const struct I2 E[] = ... ;
@depends on !c@
identifier r.I2;
identifier s.E;
@@
+ const
struct I2 E[] = ...;
// </smpl>
Signed-off-by: Németh Márton <nm127@freemail.hu>
Cc: Julia Lawall <julia@diku.dk>
Cc: cocci@diku.dk
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1302) removes the auto_pm flag from struct usb_device.
The flag's only purpose was to distinguish between autosuspends and
external suspends, but that information is now available in the
pm_message_t argument passed to suspend methods.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add D-Link DWM-162-U5 device id 1e0e:ce16 into option driver. The device
has 4 interfaces, of which 1 is handled by storage and the other 3 by
option driver.
The device appears first as CD-only 05c6:2100 device and must be switched
to 1e0e:ce16 mode either by using "eject CD" or usb_modeswitch.
The MessageContent for usb_modeswitch.conf is:
"55534243e0c26a85000000000000061b000000020000000000000000000000"
Signed-off-by: Zhang Le <r0bertz@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds the vendor and device id for the Mobilcom Debitel UMTS surf
stick (a.k.a. 4G Systems XSStick W14, MobiData MBD-200HU, ...).
To see these ids, you need to switch the stick to modem operation first
with the help of usb_modeswitch. This makes it switch from 1c9e:f000 to
1c9e:9603 and thus be recognized by the option driver.
Signed-off-by: Gernot Hillier <gernot@hillier.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add D-Link DWM-162-U5 device id 1e0e:ce16 into option driver. The device
has 4 interfaces, of which 1 is handled by storage and the other 3 by
option driver.
The device appears first as CD-only 05c6:2100 device and must be
switched to 1e0e:ce16 mode either by using "eject CD" or usb_modeswitch.
The MessageContent for usb_modeswitch.conf is:
"55534243e0c26a85000000000000061b000000020000000000000000000000"
Signed-off-by: Zhang Le <r0bertz@gentoo.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Here is a patch for Airplus MCD 650 card
Note: This device is with Victor V Kudlak, and he confirmed that this
device works with the patch.
Signed-off-by: Huzaifa Sidhpurwala <sidhpurwala.huzaifa@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
this adds autosupport usable even in an always online mode.
- enables remote wakeup on open
- autoresume for sending
- timeout based autosuspend if nothing is sent or recieved
- autosuspend without remote wakeup support on open/close
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Tested-off-by: Zhao Ming <zhao.ming9@zte.com.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add ID for Telit UC-864G GPS/UMTS/WCDMA modem and GPS receiver
to the option driver.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A few days ago i got the latest ZTE EVDO modem shown at:
http://img.alibaba.com/photo/240150115/ZTE_AC2726_EVDO_USB_Data_Modem.jpg
It seems that the latest kernel does not have support for it.
I wrote a small patch for the options.c module to add the relevant usb
ids to it.
From: Huzaifa Sidhpurwala <sidhpurwala.huzaifa@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
And indeed none of them use it. Clean this up as it will make moving to a
standard open method rather easier.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Added support for the Alcatel X060S/X200 broadband modems to the option
driver. The device starts in cd-rom emulation mode (1bbb:f000) and
requires the use of the usb_modeswitch tool to switch it to modem mode
(1bbb:0000).
Signed-off-by: Javier Martin <jmartinj@iname.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Current listed Onda ids are ZTE devices. Replace them with ZTE id define
and add more ZTE device ids. Also remove 19d2:2000, this is the id when
device is first plugged in and is a CD-only device, before the switch
using eject.
These changes are based on a previous patch by Ming Zhao
<zhao.ming9@zte.com.cn>
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Cc: Ming Zhao <zhao.ming9@zte.com.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is needed for compilation without CONFIG_PM.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
After commit f092c24049 ("USB: option:
remove unnecessary and erroneous code") the variable 'serial' becomes
unused, as gcc-4.3.2 points out:
drivers/usb/serial/option.c: In function 'option_instat_callback':
drivers/usb/serial/option.c:834: warning: unused variable 'serial'
drivers/usb/serial/option.c: In function 'option_open':
drivers/usb/serial/option.c:930: warning: unused variable 'serial'
So I removed it.
Signed-off-by: Carlos R. Mafra <crmafra@aei.mpg.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1264) removes a bunch of unnecessary and erroneous stuff
from the option USB-serial driver. Clearly there's no need to verify
that the device pointer stored in the URBs is right or to store the
same pointer over again. After all, the pointer can't change once it
has been set up.
There's also no need to call usb_clear_halt for the IN endpoint
multiple times -- in fact, doing so is an error since every time after
the first there will be active URBs queued for that endpoint. Since
the Clear-Halts don't appear to be needed at all, the patch simply
removes them.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Mauro Carvalho Chehab
