Use direct function call instead of using eemi ops for
clock_getdivider.
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Signed-off-by: Jolly Shah <jolly.shah@xilinx.com>
Link: https://lore.kernel.org/r/1587761887-4279-9-git-send-email-jolly.shah@xilinx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use direct function call instead of using eemi ops for
clock_setdivider.
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Signed-off-by: Jolly Shah <jolly.shah@xilinx.com>
Link: https://lore.kernel.org/r/1587761887-4279-8-git-send-email-jolly.shah@xilinx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During the process of debugging a processor derived from the msm8916 which
we found the new processor was not starting one of its PLLs.
After tracing the addresses and writes that downstream was doing and
comparing to upstream it became obvious that we were writing to a different
register location than downstream when trying to configure the PLL.
This error is also present in upstream msm8916.
As an example clk-pll.c::clk_pll_recalc_rate wants to write to
pll->config_reg updating the bit-field POST_DIV_RATIO. That bit-field is
defined in PLL_USER_CTL not in PLL_CONFIG_CTL. Taking the BIMC PLL as an
example
lm80-p0436-13_c_qc_snapdragon_410_processor_hrd.pdf
0x01823010 GCC_BIMC_PLL_USER_CTL
0x01823014 GCC_BIMC_PLL_CONFIG_CTL
This pattern is repeated for gpll0, gpll1, gpll2 and bimc_pll.
This error is likely not apparent since the bootloader will already have
initialized these PLLs.
This patch corrects the location of config_reg from PLL_CONFIG_CTL to
PLL_USER_CTL for all relevant PLLs on msm8916.
Fixes commit 3966fab8b6 ("clk: qcom: Add MSM8916 Global Clock Controller support")
Cc: Georgi Djakov <georgi.djakov@linaro.org>
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Link: https://lkml.kernel.org/r/20200329124116.4185447-1-bryan.odonoghue@linaro.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Use readl_relaxed_poll_timeout() for PLL lock wait which can simplify the
code a lot.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Remove many unnecessary blank lines for cleanup.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The "mali_0" or "mali_1" clock trees should not be updated while the
clock is running. Enforce this by setting CLK_SET_RATE_GATE on the
"mali_0" and "mali_1" gates. This makes the CCF switch to the "mali_1"
tree when "mali_0" is currently active and vice versa, which is exactly
what the vendor driver does when updating the frequency of the mali
clock.
Also propagate set_rate requests from the gate to the divider and from
the divider to the the mux so the GPU clock frequency can be updated at
runtime (which will be required for GPU DVFS). Don't propagate rate
changes to the mux parents because we don't want to change the MPLL
clocks (these are reserved for audio).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20200414195031.224021-3-martin.blumenstingl@googlemail.com
The "mali_0" or "mali_1" clock trees should not be updated while the
clock is running. Enforce this by setting CLK_SET_RATE_GATE on the
"mali_0" and "mali_1" gates. This makes the CCF switch to the "mali_1"
tree when "mali_0" is currently active and vice versa, which is exactly
what the vendor driver does when updating the frequency of the mali
clock.
Also propagate set_rate requests from the gate to the divider and from
the divider to the the mux so the GPU clock frequency can be updated at
runtime (which will be required for GPU DVFS). Don't propagate rate
changes to the mux parents because we don't want to change the MPLL
clocks (these are reserved for audio).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20200414195031.224021-2-martin.blumenstingl@googlemail.com
Moving to support aarch32 mode on aarch64 hardware, need to drop
the dependency on ARM64 to make the driver could be selected for
ARM32.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
ARM clk could only source from divcore or hsrun_divcore.
Follow what we already used on i.MX7D and i.MX8M SoCs, use
imx_clk_hw_cpu API. When ARM core is running normaly,
whether divcore or hwrun_divcore will finally source
from SPLL_PFD0. However SPLL_PFD0 is marked with CLK_SET_GATE,
so we need to disable SPLL_PFD0, when configure the rate.
So add CORE and HSRUN_CORE virtual clk to make it easy to
configure the clk using imx_clk_hw_cpu API.
Since CORE and HSRUN_CORE already marked with CLK_IS_CRITICAL, no
need to set ARM as CLK_IS_CRITICAL. And when set the rate of ARM clk,
prograting it the parent with CLK_SET_RATE_PARENT will finally set
the SPLL_PFD0 clk.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The HDMI TX controller requires the hdmi_sys clock to be enabled. Allow
changing the whole clock tree now that we know that one of our drivers
requires this.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20200330234535.3327513-3-martin.blumenstingl@googlemail.com
Export the HDMI system clock (used by the HDMI transmitter) so it can be
used in the dt-bindings.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20200330234535.3327513-2-martin.blumenstingl@googlemail.com
This file seems to be for R9A06G032 only. So replace reference to
R9A09G032 by R9A06G032 to avoid confusion.
AFAIK, R9A09G032 does'nt exist.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/20200413041709.3630-1-christophe.jaillet@wanadoo.fr
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
round_down() can only round to powers of 2. If round_down() is asked
to round to something that is not a power of 2, incorrect results are
produced. The incorrect results can be both too large and too small.
Instead, use rounddown() which can round to any number.
Fixes: 6a721db180 ("clk: sunxi: Add A31 clocks support")
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Don't gate uart1_eb which provides console clock, gating that clock would
make serial stop working if serial driver didn't enable that explicitly.
Fixes: 0e4b8a2349 ("clk: sprd: add clocks support for SC9863A")
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Link: https://lkml.kernel.org/r/20200408020234.31764-1-zhang.lyra@gmail.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The newly added function is only built into the kernel if mmp2
is enabled, causing a link error otherwise.
arm-linux-gnueabi-ld: drivers/clk/mmp/clk.o: in function `mmp_register_pll_clks':
clk.c:(.text+0x6dc): undefined reference to `mmp_clk_register_pll'
Move it to a different file to get it to link.
Fixes: 5d34d0b32d ("clk: mmp2: Add support for PLL clock sources")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lkml.kernel.org/r/20200408160518.2798571-1-arnd@arndb.de
Reported-by: Guenter Roeck <linux@roeck-us.net>
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The __clk_hw_register_fixed_rate_with_accuracy() function (with two '_')
does not exist, and apparently never did:
drivers/clk/clk-asm9260.c: In function 'asm9260_acc_init':
drivers/clk/clk-asm9260.c:279:7: error: implicit declaration of function '__clk_hw_register_fixed_rate_with_accuracy'; did you mean 'clk_hw_register_fixed_rate_with_accuracy'? [-Werror=implicit-function-declaration]
279 | hw = __clk_hw_register_fixed_rate_with_accuracy(NULL, NULL, pll_clk,
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
| clk_hw_register_fixed_rate_with_accuracy
drivers/clk/clk-asm9260.c:279:5: error: assignment to 'struct clk_hw *' from 'int' makes pointer from integer without a cast [-Werror=int-conversion]
279 | hw = __clk_hw_register_fixed_rate_with_accuracy(NULL, NULL, pll_clk,
| ^
From what I can tell, __clk_hw_register_fixed_rate() is the correct
API here, so use that instead.
Fixes: 728e309674 ("clk: asm9260: Use parent accuracy in fixed rate clk")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lkml.kernel.org/r/20200408155402.2138446-1-arnd@arndb.de
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Setting a CAN bitrate of 800kbit/s fails with a bitrate error of 1.3% if the
flexcan module is clocked at 30MHz (CAN_CLK_ROOT). This patch changes the clock
frequency from 30MHz to 40MHz which allows to support all bitrates recommended
by CiA.
The patch sets CAN_CLK_SEL to 80MHz by changing its clock parent from
CLK_PLL3_60M to CLK_PLL3_80M. The post-divider CAN_CLK_PODF is set to /2 by
default which makes 40MHz CAN_CLK_ROOT from its parent CAN_CLK_SEL.
Background:
CAN in Automation document 102 (CiA102) recommends the CAN bitrates 10, 20, 50,
125, 250, 500, 800 and 1000kbit/s.
With the flexcan serial clock at 30MHz (original value) setting some common
bitrates ("ip link set canX type can bitrate <bitrate>") gives the following
results:
requested value / actually set value
5000: bitrate 5000 sample-point 0.708
10000: bitrate 10000 sample-point 0.866
20000: bitrate 20000 sample-point 0.866
40000: bitrate 40000 sample-point 0.866
50000: bitrate 50000 sample-point 0.866
80000: bitrate 80000 sample-point 0.866
100000: bitrate 100000 sample-point 0.866
125000: bitrate 125000 sample-point 0.875
250000: bitrate 250000 sample-point 0.866
400000: bitrate 400000 sample-point 0.866
500000: bitrate 500000 sample-point 0.866
666666: bitrate 666666 sample-point 0.800
800000: bitrate 789473 sample-point 0.789 !!!bitrate error 1.3%
1000000: bitrate 1000000 sample-point 0.733
With the flexcan serial clock at 40MHz (new value) we get this:
5000: no more possible
10000: bitrate 10000 sample-point 0.875
20000: bitrate 20000 sample-point 0.875
40000: bitrate 40000 sample-point 0.850
50000: bitrate 50000 sample-point 0.875
80000: bitrate 80000 sample-point 0.850
100000: bitrate 100000 sample-point 0.875
125000: bitrate 125000 sample-point 0.875
250000: bitrate 250000 sample-point 0.875
400000: bitrate 400000 sample-point 0.850
500000: bitrate 500000 sample-point 0.875
666666: bitrate 666666 sample-point 0.800
800000: bitrate 800000 sample-point 0.800
1000000: bitrate 1000000 sample-point 0.750
A drawback of the modification is that 5kbit/s is no more supported.
Setting the flexcan serial clock to 60MHz or 80MHz would produce similar
results but with losing even more bitrates at the lower end.
Changing the flexcan serial clock to 40MHz might apply for other SoCs
using the flaxcan module as well (e.g. imx6q/d/s..). But since I don't
have such hardware to test I did not add this to the patch.
Signed-off-by: Georg Waibel <georg.waibel@wiedemann-group.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
There is no strong reason for this to use CLK_OF_DECLARE instead of
being a platform driver. Plus, MMSYS provides clocks but also a shared
register space for the mediatek-drm and the mediatek-mdp
driver. So move the MMSYS clocks to a new platform driver and also
create a new MMSYS platform driver in drivers/soc/mediatek that
instantiates the clock driver.
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The following changes prevent the unrecoverable freezes and rcu_sched
stall warnings experienced in each of my attempts to take advantage of
lima.
Replace the COMPOSITE_NOGATE definition of aclk_gpu_pre with a
COMPOSITE that retains the selection of HDMIPHY as the PLL source, but
instead makes uses of the aclk_gpu PLL source gate and parent names
defined by mux_pll_src_4plls_p rather than mux_aclk_gpu_pre_p.
Remove the now unused mux_aclk_gpu_pre_p and the four named but also
unused definitions (cpll_gpu, gpll_gpu, hdmiphy_gpu and usb480m_gpu)
of the aclk_gpu PLL source gate.
Use the correct gate offset for aclk_gpu and aclk_gpu_noc.
Fixes: 307a2e9ac5 ("clk: rockchip: add clock controller for rk3228")
Cc: stable@vger.kernel.org
Signed-off-by: Justin Swartz <justin.swartz@risingedge.co.za>
[double-checked against SoC manual and added fixes tag]
Link: https://lore.kernel.org/r/20200114162503.7548-1-justin.swartz@risingedge.co.za
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
majority of the diff is the normal collection of driver additions for new SoCs
and non-critical clk data fixes and updates. The framework must be middle aged.
The two biggest directories in the diffstat show that the Qualcomm and Unisoc
support added a handful of big drivers for new SoCs but that's not really the
whole story because those new drivers tend to add large numbers of lines of clk
data. There's a handful of AT91 clk drivers added this time around too and a
bunch of improvements to drivers like the i.MX driver. All around lots of
updates and fixes in various clk drivers which is good to see.
The core framework has only one real major change which has been baking in next
for the past couple months. It fixes the framework so that it stops caching a
clk's phase when the phase clk_op returns an error. Before this change we would
consider some negative errno as a phase and that just doesn't make sense.
Core:
- Don't show clk phase when it is invalid
New Drivers:
- Add support for Unisoc SC9863A clks
- Qualcomm SM8250 RPMh and MSM8976 RPM clks
- Qualcomm SM8250 Global Clock Controller (GCC) support
- Qualcomm SC7180 Modem Clock Controller (MSS CC) support
- EHRPWM's TimeBase clock(TBCLK) for TI AM654 SoCs
- Support PMC clks on at91sam9n12, at91rm9200, sama5d3, and at91sam9g45 SoCs
Updates:
- GPU GX GDSC support on Qualcomm sc7180
- Fixes and improvements for the Marvell MMP2/MMP3 SoC clk drivers
- A series from Anson to convert i.MX8 clock bindings to json-schema
- Update i.MX pll14xx driver to include new frequency entries for pll1443x table,
and return error for invalid PLL type
- Add missing of_node_put() call for a number of i.MX clock drivers
- Drop flag CLK_IS_CRITICAL from 'A53_CORE' mux clock, as we already
have the flag on its child cpu clock
- Fix a53 cpu clock for i.MX8 drivers to get it source from ARM PLL
via CORE_SEL slice, and source from A53 CCM clk root when we need to
change ARM PLL frequency. Thus, we can support core running above
1GHz safely
- Update i.MX pfdv2 driver to check zero rate and use determine_rate for
getting the best rate
- Add CLKO2 for imx8mm, SNVS clock for imx8mn, and PXP clock for imx7d
- Remove PMC clks from Tegra clk driver
- Improved clock/reset handling for the Renesas R-Car USB2 Clock Selector
- Conversion to json-schema of the Renesas CPG/MSSR DT bindings
- Add Crypto clocks on Renesas R-Car M3-W/W+, M3-N, E3, and D3
- Add RPC (QSPI/HyperFLASH) clocks on Renesas R-Car H3, M3-W/W+, and M3-N
- Update Amlogic audio clock gate hierarchy for meson8 and gxbb
- Update Amlogic g12a spicc clock sources
- Support for Ingenic X1000 TCU clks
-----BEGIN PGP SIGNATURE-----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=ZoI6
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"There's not much to see in the core framework this time around.
Instead the majority of the diff is the normal collection of driver
additions for new SoCs and non-critical clk data fixes and updates.
The framework must be middle aged.
The two biggest directories in the diffstat show that the Qualcomm and
Unisoc support added a handful of big drivers for new SoCs but that's
not really the whole story because those new drivers tend to add large
numbers of lines of clk data. There's a handful of AT91 clk drivers
added this time around too and a bunch of improvements to drivers like
the i.MX driver. All around lots of updates and fixes in various clk
drivers which is good to see.
The core framework has only one real major change which has been
baking in next for the past couple months. It fixes the framework so
that it stops caching a clk's phase when the phase clk_op returns an
error. Before this change we would consider some negative errno as a
phase and that just doesn't make sense.
Core:
- Don't show clk phase when it is invalid
New Drivers:
- Add support for Unisoc SC9863A clks
- Qualcomm SM8250 RPMh and MSM8976 RPM clks
- Qualcomm SM8250 Global Clock Controller (GCC) support
- Qualcomm SC7180 Modem Clock Controller (MSS CC) support
- EHRPWM's TimeBase clock(TBCLK) for TI AM654 SoCs
- Support PMC clks on at91sam9n12, at91rm9200, sama5d3, and
at91sam9g45 SoCs
Updates:
- GPU GX GDSC support on Qualcomm sc7180
- Fixes and improvements for the Marvell MMP2/MMP3 SoC clk drivers
- A series from Anson to convert i.MX8 clock bindings to json-schema
- Update i.MX pll14xx driver to include new frequency entries for
pll1443x table, and return error for invalid PLL type
- Add missing of_node_put() call for a number of i.MX clock drivers
- Drop flag CLK_IS_CRITICAL from 'A53_CORE' mux clock, as we already
have the flag on its child cpu clock
- Fix a53 cpu clock for i.MX8 drivers to get it source from ARM PLL
via CORE_SEL slice, and source from A53 CCM clk root when we need
to change ARM PLL frequency. Thus, we can support core running
above 1GHz safely
- Update i.MX pfdv2 driver to check zero rate and use determine_rate
for getting the best rate
- Add CLKO2 for imx8mm, SNVS clock for imx8mn, and PXP clock for
imx7d
- Remove PMC clks from Tegra clk driver
- Improved clock/reset handling for the Renesas R-Car USB2 Clock
Selector
- Conversion to json-schema of the Renesas CPG/MSSR DT bindings
- Add Crypto clocks on Renesas R-Car M3-W/W+, M3-N, E3, and D3
- Add RPC (QSPI/HyperFLASH) clocks on Renesas R-Car H3, M3-W/W+, and
M3-N
- Update Amlogic audio clock gate hierarchy for meson8 and gxbb
- Update Amlogic g12a spicc clock sources
- Support for Ingenic X1000 TCU clks"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (146 commits)
clk: sprd: fix to get a correct ibias of pll
dt-bindings: imx8mm-clock: Fix the file path
dt-bindings: imx8mq-clock: Fix the file path
clk: qcom: rpmh: Drop unnecessary semicolons
clk: qcom: rpmh: Simplify clk_rpmh_bcm_send_cmd()
clk: tegra: Use NULL for pointer initialization
clk: sprd: add clocks support for SC9863A
clk: sprd: support to get regmap from parent node
clk: sprd: Add macros for referencing parents without strings
clk: sprd: Add dt-bindings include file for SC9863A
dt-bindings: clk: sprd: add bindings for sc9863a clock controller
dt-bindings: clk: sprd: rename the common file name sprd.txt to SoC specific
clk: sprd: add gate for pll clocks
MAINTAINERS: dt: update reference for arm-integrator.txt
clk: mmp2: Fix bit masks for LCDC I/O and pixel clocks
clk: mmp2: Add clock for fifth SD HCI on MMP3
dt-bindings: marvell,mmp2: Add clock id for the fifth SD HCI on MMP3
clk: mmp2: Add clocks for the thermal sensors
dt-bindings: marvell,mmp2: Add clock ids for the thermal sensors
clk: mmp2: add the GPU clocks
...
Most of the commits are for additional hardware support and minor fixes
for existing machines for all the usual platforms: qcom, amlogic, at91,
gemini, mediatek, ti, socfpga, i.mx, layerscape, uniphier, rockchip,
exynos, ux500, mvebu, tegra, stm32, renesas, sunxi, broadcom, omap,
and versatile.
The conversion of binding files to machine-readable yaml format
continues, along with fixes found during the validation.
Andre Przywara takes over maintainership for the old Calxeda Highbank
platform and provides a number of updates.
The OMAP2+ platforms see a continued move from platform data into
dts files, for many devices that relied on a mix of auxiliary data
in addition to the DT description
A moderate number of new SoCs and machines are added, here is a full
list:
- Two new Qualcomm SoCs with their evaluation boards: Snapdragon 865
(SM8250) is the current high-end phone chip, and IPQ6018 is a new
WiFi-6 router chip.
- Mediatek MT8516 application processor SoC for voice assistants, along
with the "pumpkin" development board
- NXP i.MX8M Plus SoC, a variant of the popular i.MX8M, along with an
evaluation board.
- Kontron "sl28" board family based on NXP LS1028A
- Eleven variations of the new i.MX6 TechNexion Pico board, combining
the "dwarf", "hobbit", "nymph" and "pi" baseboards with i.MX6/i.MX7
SoM carriers
- Three additional variants of the Toradex Colibri board family, all
based on versions of the NXP i.MX7.
- The Pinebook Pro laptop based on Rockchip RK3399
- Samsung S7710 Galaxy Xcover 2, a 2013 vintage Android phone based on
the ST-Ericsson u8500 platform
- DH Electronics DHCOM SoM and PDK2 rev. 400 carrier based on
STMicroelectronics stm32mp157
- Renesas M3ULCB starter kit for R-Car M3-W+
- Hoperun HiHope development board with Renesas RZ/G2M
- Pine64 PineTab tablet and PinePhone phone, both based on Allwinner A64
- Linutronix Testbox v2 for the Lamobo R1 router, based on Allwinner A20
- PocketBook Touch Lux 3 ebook reader, based on Allwinner A13
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=ye2F
-----END PGP SIGNATURE-----
Merge tag 'arm-dt-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM devicetree updates from Arnd Bergmann:
"Most of the commits are for additional hardware support and minor
fixes for existing machines for all the usual platforms: qcom,
amlogic, at91, gemini, mediatek, ti, socfpga, i.mx, layerscape,
uniphier, rockchip, exynos, ux500, mvebu, tegra, stm32, renesas,
sunxi, broadcom, omap, and versatile.
The conversion of binding files to machine-readable yaml format
continues, along with fixes found during the validation. Andre
Przywara takes over maintainership for the old Calxeda Highbank
platform and provides a number of updates.
The OMAP2+ platforms see a continued move from platform data into dts
files, for many devices that relied on a mix of auxiliary data in
addition to the DT description
A moderate number of new SoCs and machines are added, here is a full
list:
- Two new Qualcomm SoCs with their evaluation boards: Snapdragon 865
(SM8250) is the current high-end phone chip, and IPQ6018 is a new
WiFi-6 router chip.
- Mediatek MT8516 application processor SoC for voice assistants,
along with the "pumpkin" development board
- NXP i.MX8M Plus SoC, a variant of the popular i.MX8M, along with an
evaluation board.
- Kontron "sl28" board family based on NXP LS1028A
- Eleven variations of the new i.MX6 TechNexion Pico board, combining
the "dwarf", "hobbit", "nymph" and "pi" baseboards with i.MX6/i.MX7
SoM carriers
- Three additional variants of the Toradex Colibri board family, all
based on versions of the NXP i.MX7.
- The Pinebook Pro laptop based on Rockchip RK3399
- Samsung S7710 Galaxy Xcover 2, a 2013 vintage Android phone based
on the ST-Ericsson u8500 platform
- DH Electronics DHCOM SoM and PDK2 rev. 400 carrier based on
STMicroelectronics stm32mp157
- Renesas M3ULCB starter kit for R-Car M3-W+
- Hoperun HiHope development board with Renesas RZ/G2M
- Pine64 PineTab tablet and PinePhone phone, both based on Allwinner
A64
- Linutronix Testbox v2 for the Lamobo R1 router, based on Allwinner
A20
- PocketBook Touch Lux 3 ebook reader, based on Allwinner A13"
* tag 'arm-dt-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (520 commits)
ARM: dts: ux500: Fix missing node renames
arm64: dts: Revert "specify console via command line"
MAINTAINERS: Update Calxeda Highbank maintainership
arm: dts: calxeda: Group port-phys and sgpio-gpio items
arm: dts: calxeda: Fix interrupt grouping
arm: dts: calxeda: Provide UART clock
arm: dts: calxeda: Basic DT file fixes
arm64: dts: specify console via command line
ARM: dts: at91: sama5d27_wlsom1_ek: add USB device node
ARM: dts: gemini: Add thermal zone to DIR-685
ARM: dts: gemini: Rename IDE nodes
ARM: socfpga: arria10: Add ptp_ref clock to ethernet nodes
arm64: dts: ti: k3-j721e-mcu: add scm node and phy-gmii-sel nodes
arm64: dts: ti: k3-am65-mcu: add phy-gmii-sel node
arm64: dts: ti: k3-am65-mcu: Add DMA entries for ADC
arm64: dts: ti: k3-am65-main: Add DMA entries for main_spi0
arm64: dts: ti: k3-j721e-mcu-wakeup: Add DMA entries for ADC
arm64: dts: ti: k3-am65: Add clocks to dwc3 nodes
arm64: dts: meson-g12b-odroid-n2: add SPIFC controller node
arm64: dts: khadas-vim3: add SPIFC controller node
...
- Add support for Unisoc SC9863A clks
- GPU GX GDSC support on Qualcomm sc7180
- Qualcomm SM8250 RPMh and MSM8976 RPM clks
- Qualcomm SM8250 Global Clock Controller (GCC) support
- Qualcomm SC7180 Modem Clock Controller (MSS CC) support
* clk-unisoc:
clk: sprd: fix to get a correct ibias of pll
clk: sprd: add clocks support for SC9863A
clk: sprd: support to get regmap from parent node
clk: sprd: Add macros for referencing parents without strings
clk: sprd: Add dt-bindings include file for SC9863A
dt-bindings: clk: sprd: add bindings for sc9863a clock controller
dt-bindings: clk: sprd: rename the common file name sprd.txt to SoC specific
clk: sprd: add gate for pll clocks
* clk-tegra:
clk: tegra: Use NULL for pointer initialization
clk: tegra: Remove audio clocks configuration from clock driver
clk: tegra: Remove tegra_pmc_clk_init along with clk ids
clk: tegra: Remove CLK_M_DIV fixed clocks
clk: tegra: Fix Tegra PMC clock out parents
clk: tegra: Add Tegra OSC to clock lookup
clk: tegra: Add support for OSC_DIV fixed clocks
dt-bindings: soc: tegra-pmc: Add ID for Tegra PMC 32 kHz blink clock
dt-bindings: soc: tegra-pmc: Add Tegra PMC clock bindings
dt-bindings: tegra: Convert Tegra PMC bindings to YAML
dt-bindings: clock: tegra: Add IDs for OSC clocks
* clk-qcom: (21 commits)
clk: qcom: rpmh: Drop unnecessary semicolons
clk: qcom: rpmh: Simplify clk_rpmh_bcm_send_cmd()
clk: qcom: gcc: Add USB3 PIPE clock and GDSC for SM8150
ipq806x: gcc: Added the enable regs and mask for PRNG
clk: qcom: Add modem clock controller driver for SC7180
clk: qcom: gcc: Add support for modem clocks in GCC
dt-bindings: clock: Add YAML schemas for the QCOM MSS clock bindings
clk: qcom: clk-rpm: add missing rpm clk for ipq806x
clk: qcom: gcc: Add global clock controller driver for SM8250
dt-bindings: clock: Add SM8250 GCC clock bindings
clk: qcom: clk-alpha-pll: Add support for controlling Lucid PLLs
clk: qcom: clk-alpha-pll: Refactor trion PLL
clk: qcom: clk-alpha-pll: Use common names for defines
dt-bindings: clock: rpmcc: Document msm8976 compatible
clk: qcom: smd: Add support for MSM8976 rpm clocks
clk: qcom: clk-rpmh: Wait for completion when enabling clocks
clk: qcom: rpmh: Add support for RPMH clocks on SM8250
dt-bindings: clock: Add RPMHCC bindings for SM8250
clk: qcom: alpha-pll: Make error prints more informative
clk: qcom: gpucc: Add support for GX GDSC for SC7180
...
* clk-imx: (43 commits)
dt-bindings: imx8mm-clock: Fix the file path
dt-bindings: imx8mq-clock: Fix the file path
clk: imx: clk-gate2: Pass the device to the register function
clk: imx7d: Add PXP clock
clk: imx8mq: A53 core clock no need to be critical
clk: imx8mp: A53 core clock no need to be critical
clk: imx8mm: A53 core clock no need to be critical
clk: imx8mn: A53 core clock no need to be critical
clk: imx: pllv4: use prepare/unprepare
clk: imx: pfdv2: determine best parent rate
clk: imx: pfdv2: switch to use determine_rate
clk: imx: Fix division by zero warning on pfdv2
clk: imx: clk-sscg-pll: Drop unnecessary initialization
clk: imx: pll14xx: Return error if pll type is invalid
clk: imx: imx8mp: fix a53 cpu clock
clk: imx: imx8mn: fix a53 cpu clock
clk: imx: imx8mm: fix a53 cpu clock
clk: imx: imx8mq: fix a53 cpu clock
clk: imx8mp: Rename the IMX8MP_CLK_HDMI_27M clock
clk: imx8mn: Remove unused includes
...
The code changes are mostly for 32-bit platforms and include:
- Lots of updates for the Nvidia Tegra platform, including
cpuidle, pmc, and dt-binding changes
- Microchip at91 power management updates for the recently added
sam9x60 SoC
- Treewide setup_irq deprecation by afzal mohammed
- STMicroelectronics stm32 gains earlycon support
- Renesas platforms with Cortex-A9 can now use the global timer
- Some TI OMAP2+ platforms gain cpuidle support
- Various cleanups for the i.MX6 and Orion platforms, as well as
Kconfig files across all platforms
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=UTk1
-----END PGP SIGNATURE-----
Merge tag 'arm-soc-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC updates from Arnd Bergmann:
"The code changes are mostly for 32-bit platforms and include:
- Lots of updates for the Nvidia Tegra platform, including cpuidle,
pmc, and dt-binding changes
- Microchip at91 power management updates for the recently added
sam9x60 SoC
- Treewide setup_irq deprecation by afzal mohammed
- STMicroelectronics stm32 gains earlycon support
- Renesas platforms with Cortex-A9 can now use the global timer
- Some TI OMAP2+ platforms gain cpuidle support
- Various cleanups for the i.MX6 and Orion platforms, as well as
Kconfig files across all platforms"
* tag 'arm-soc-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (75 commits)
ARM: qcom: Add support for IPQ40xx
ARM: mmp: replace setup_irq() by request_irq()
ARM: cns3xxx: replace setup_irq() by request_irq()
ARM: spear: replace setup_irq() by request_irq()
ARM: ep93xx: Replace setup_irq() by request_irq()
ARM: iop32x: replace setup_irq() by request_irq()
arm: mach-dove: Mark dove_io_desc as __maybe_unused
ARM: orion: replace setup_irq() by request_irq()
ARM: debug: stm32: add UART early console support for STM32MP1
ARM: debug: stm32: add UART early console support for STM32H7
ARM: debug: stm32: add UART early console configuration for STM32F7
ARM: debug: stm32: add UART early console configuration for STM32F4
cpuidle: tegra: Disable CC6 state if LP2 unavailable
cpuidle: tegra: Squash Tegra114 driver into the common driver
cpuidle: tegra: Squash Tegra30 driver into the common driver
cpuidle: Refactor and move out NVIDIA Tegra20 driver into drivers/cpuidle
ARM: tegra: cpuidle: Remove unnecessary memory barrier
ARM: tegra: cpuidle: Make abort_flag atomic
ARM: tegra: cpuidle: Handle case where secondary CPU hangs on entering LP2
ARM: tegra: Make outer_disable() open-coded
...
The current driver is getting a wrong ibias index of pll clocks from
number 1. This patch fix that issue, then getting ibias index from 0.
Fixes: 3e37b00558 ("clk: sprd: add adjustable pll support")
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Link: https://lkml.kernel.org/r/20200330021640.14133-1-zhang.lyra@gmail.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The imx SC api strongly assumes that messages are composed out of
4-bytes words but some of our message structs have odd sizeofs.
This produces many oopses with CONFIG_KASAN=y.
Fix by marking with __aligned(4).
Fixes: 666aed2d13 ("clk: imx: scu: add set parent support")
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Link: https://lkml.kernel.org/r/aad021e432b3062c142973d09b766656eec18fde.1582216144.git.leonard.crestez@nxp.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The imx SC api strongly assumes that messages are composed out of
4-bytes words but some of our message structs have odd sizeofs.
This produces many oopses with CONFIG_KASAN=y.
Fix by marking with __aligned(4).
Fixes: fe37b48204 ("clk: imx: add scu clock common part")
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Link: https://lkml.kernel.org/r/10e97a04980d933b2cfecb6b124bf9046b6e4f16.1582216144.git.leonard.crestez@nxp.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Some functions end in }; which is just bad style. Remove the extra
semicolon.
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Taniya Das <tdas@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lkml.kernel.org/r/20200309221232.145630-3-sboyd@kernel.org
This function has some duplication in unlocking a mutex and returns in a
few different places. Let's use some if statements to consolidate code
and make this a bit easier to read.
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
CC: Taniya Das <tdas@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lkml.kernel.org/r/20200309221232.145630-2-sboyd@kernel.org
Some SC9863a clock nodes would be the child of a syscon node, clocks can
use the regmap of syscon device directly for this kind of cases.
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Link: https://lkml.kernel.org/r/20200304072730.9193-7-zhang.lyra@gmail.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
With the new clk parenting code, clk_init_data was expanded to include
.parent_hws and .parent_data, for clk drivers to specify parents without
name strings of clocks.
Also some macros were added for using these two items to reference
clock parents. Based on that to expand macros for sprd clocks:
- SPRD_*_DATA, take an array of struct clk_parent_data * as its parents
which should be a combination of .fw_name (devicetree clock-names),
.hw (pointers to a local struct clk_hw).
- SPRD_*_HW, take a local struct clk_hw pointer, instead of a string, as
its parent.
- SPRD_*_FW_NAME, take a string of clock-names decleared in the device
tree as the clock parent.
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Link: https://lkml.kernel.org/r/20200304072730.9193-6-zhang.lyra@gmail.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Some sprd's gate clocks are used to the switch of pll, which
need to wait a certain time for stable after being enabled.
Signed-off-by: Xiaolong Zhang <xiaolong.zhang@unisoc.com>
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Link: https://lkml.kernel.org/r/20200304072730.9193-2-zhang.lyra@gmail.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
They were reversed because I read the datasheet upside down.
Actually there is no datasheet, but I ended up understanding the
comments in Open Firmware driver wrong.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Link: https://lkml.kernel.org/r/20200309194254.29009-18-lkundrak@v3.sk
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
There's one extra SDHCI on MMP3, used by the internal SD card on OLPC
XO-4. Add a clock for it.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Link: https://lkml.kernel.org/r/20200309194254.29009-17-lkundrak@v3.sk
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
There are more PLLs on MMP3 and are configured slightly differently.
Tested on a MMP3-based Dell Wyse 3020 machine.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Link: https://lkml.kernel.org/r/20200309194254.29009-10-lkundrak@v3.sk
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The MMP3's are similar enough to MMP2, but there are differencies, such
are more clocks available on the newer model. We want to tell which
platform are we on.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Link: https://lkml.kernel.org/r/20200309194254.29009-8-lkundrak@v3.sk
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The hardcoded values for PLL1 and PLL2 are wrong. PLL1 is slightly
off -- it defaults to 797.33 MHz, not 800 MHz. PLL2 is disabled by default,
but also configurable.
Tested on a MMP2-based OLPC XO-1.75 laptop, with PLL1=797.33 and various
values of PLL2 set via set-pll2-520mhz, set-pll2-910mhz and
set-pll2-988mhz Open Firmware words.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Link: https://lkml.kernel.org/r/20200309194254.29009-6-lkundrak@v3.sk
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
As we want to move these clocks over to probe from the device
tree we add a device tree probing path.
The old platform data path will be deleted once we have the
device tree overall code in place.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lkml.kernel.org/r/20200219103326.81120-3-linus.walleij@linaro.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
When requesting a rate superior to the parent's rate, it would return
-EINVAL instead of simply returning the parent's rate like it should.
Fixes: 4f89e4b8f1 ("clk: ingenic: Add driver for the TCU clocks")
Cc: stable@vger.kernel.org
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lkml.kernel.org/r/20200213161952.37460-2-paul@crapouillou.net
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Exit jz4770_cgu_init() if the 'cgu' pointer we get is NULL, since the
pointer is passed as argument to functions later on.
Fixes: 7a01c19007 ("clk: Add Ingenic jz4770 CGU driver")
Cc: stable@vger.kernel.org
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Reported-by: kbuild test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lkml.kernel.org/r/20200213161952.37460-1-paul@crapouillou.net
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
On TI's AM654/J721e SoCs, certain clocks can be gated/ungated by setting
a single bit in SoC's System Control Module registers. Sometime more
than one clock control can be in the same register.
Add a driver to support such clocks using syscon framework. Driver
currently supports controlling EHRPWM's TimeBase clock(TBCLK) for AM654
SoC.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lkml.kernel.org/r/20200227053529.16479-3-vigneshr@ti.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add "jz4780_core1_enable()" for enable the second core of JZ4780,
prepare for later commits.
Tested-by: H. Nikolaus Schaller <hns@goldelico.com>
Tested-by: Paul Boddie <paul@boddie.org.uk>
Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Link: https://lkml.kernel.org/r/1582215889-113034-3-git-send-email-zhouyanjie@wanyeetech.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
X1000 has a different TCU, since X1000 OST has been independent of TCU.
This patch is add TCU support of X1000, and prepare for later OST driver.
Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
Link: https://lkml.kernel.org/r/1584457893-40418-3-git-send-email-zhouyanjie@wanyeetech.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This adds the USB3 PIPE clock and GDSC structures, so
that the USB driver can vote for these resources to be
enabled/disabled when required. Both are needed for SS
and HS USB paths to operate properly. The GDSC will
allow the USB system to be brought out of reset, while
the PIPE clock is needed for data transactions between
the PHY and controller.
Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>
Link: https://lkml.kernel.org/r/1584478412-7798-2-git-send-email-wcheng@codeaurora.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Kernel got hanged while reading from /dev/hwrng at the
time of PRNG clock enable
Fixes: 24d8fba44a "clk: qcom: Add support for IPQ8064's global clock controller (GCC)"
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Link: https://lkml.kernel.org/r/20200318131657.345-1-ansuelsmth@gmail.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add support for the modem clock controller found on SC7180
based devices. This would allow modem drivers to probe and
control their clocks.
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Link: https://lkml.kernel.org/r/1584596131-22741-4-git-send-email-tdas@codeaurora.org
Tested-by: Sibi Sankar <sibis@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add the required modem clocks in global clock controller which are
required to bring the modem out of reset.
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Link: https://lkml.kernel.org/r/1584596131-22741-3-git-send-email-tdas@codeaurora.org
Tested-by: Sibi Sankar <sibis@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
We are missing alwon ethernet clock for dm814x and this prevents us
from probing the CPSW with device tree only data. Looks like Ethernet
currently only works if it has been enabled in the bootloader.
Looks like relying on the bootloader clocks is not an issue with the
mainline kernel currently, but it will be an issue when configuring
CPSW Ethernet to probe with device tree data only as we will be managing
the clocks.
Fixes: 26ca2e9738 ("clk: ti: dm814: add clkctrl clock data")
Cc: linux-clk@vger.kernel.org
Cc: Graeme Smecher <gsmecher@threespeedlogic.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Tero Kristo <t-kristo@ti.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Currently enabling clkctrl clock on am4 can fail for RTC as the clock
parent is wrong for RTC.
Fixes: 76a1049b84 ("clk: ti: am43xx: add new clkctrl data for am43xx")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lkml.kernel.org/r/20200221171030.39326-1-tony@atomide.com
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
- A couple of fixes on i.MX8MP clock driver to correct HDMI_AXI and
ENET_QOS_ROOT parent clock.
-----BEGIN PGP SIGNATURE-----
iQFIBAABCgAyFiEEFmJXigPl4LoGSz08UFdYWoewfM4FAl5uxfEUHHNoYXduZ3Vv
QGtlcm5lbC5vcmcACgkQUFdYWoewfM6eygf8DVknKD0zOdcqyvRKWllCkHKWLiQW
DphyaMelEXhszKbQ3/ICbYrRG6SE9pk38nDNTGWIpY4ZE+AIzeR5ROfC12MWCu/j
nGXcDGOD3g17OvPQbxSpQnrdq4w2pgcQDyoE3WsL0lvtVEQFEeg4/jrif6XlCqyI
TEWQ1uPwpAOX+sfmdNfNkuRl5IXuOqZ6oFYhY2S5O62W7ejwj1YsuTU9EV5eTSAv
2sBOTP5WgWcHRhzGlfhvDjZJtFy5d6qos4hw2p7MZGis5RlLhX/qwvfl6hWU28rD
OKEXN2+DFB1AGDMtdV0lf9IpQOGfbDJiY0Pr0erEFSMVfDVSgR0FHV57Zg==
=tiMl
-----END PGP SIGNATURE-----
Merge tag 'imx-clk-fixes-5.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into clk-fixes
Pull a few more i.MX clk fixes for 5.6:
- A couple of fixes on i.MX8MP clock driver to correct HDMI_AXI and
ENET_QOS_ROOT parent clock
* tag 'imx-clk-fixes-5.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
clk: imx8mp: Correct the enet_qos parent clock
clk: imx8mp: Correct IMX8MP_CLK_HDMI_AXI clock parent
The device needs to be passed on to the clk_hw_register.
Fixes: 1f9aec9662 ("clk: imx: clk-gate2: Switch to clk_hw based API")
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The PXP has a single CCGR clock gate, gating both the IPG_CLK_ROOT and
the MAIN_AXI_CLK_ROOT. Add a single clock to cover both.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
enet_qos is for eqos tsn AXI bus clock whose clock source is from
ccm_enet_axi_clk_root, and controlled by CCM_CCGR59(offset 0x43b0)
and CCM_CCGR64(offset 0x4400), so correct enet_qos root clock's
parent clock to sim_enet.
Fixes: 9c140d9926 ("clk: imx: Add support for i.MX8MP clock driver")
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
IMX8MP_CLK_HDMI_AXI should be from imx8mp_media_axi_sels instead
of imx8mp_media_apb_sels, fix it.
Fixes: 9c140d9926 ("clk: imx: Add support for i.MX8MP clock driver")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add missing definition of rpm clk for ipq806x soc
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Acked-by: John Crispin <john@phrozen.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lkml.kernel.org/r/20200310143756.244-1-ansuelsmth@gmail.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Current clock driver enables PLLA, cdev1 on Tegra20 and extern1 on
Tegra30 and above as a part of clocks init and there is no need to
have these audio clocks enabled by the clock driver.
extern1 is used as parent for clk_out_1 and clk_out_1 is dedicated
for audio mclk on Tegra30 and above Tegra platforms and these clocks
are taken care by ASoC driver.
So, this patch removes audio related clocks configuration from clock
init of Tegra20 and above.
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Current Tegra clock driver registers PMC clocks clk_out_1, clk_out_2,
clk_out_3 and 32KHz blink output in tegra_pmc_init() which does direct
PMC register access during clk_ops and these PMC register read and write
access will not happen when PMC is in secure mode.
Any direct PMC register access from non-secure world will not go
through.
All the PMC clocks are moved to Tegra PMC driver with PMC as a clock
provider.
This patch removes tegra_pmc_clk_init along with corresponding clk ids
from Tegra clock driver.
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra has no CLK_M_DIV2 and CLK_M_DIV4 clocks and instead it has
OSC_DIV2 and OSC_DIV4 clocks from OSC pads which are the possible
parents of PMC clocks for Tegra30 through Tegra210.
Tegra PMC clock parents are changed to use OSC_DIV clocks.
So, this patch removes CLK_M_DIV fixed clocks
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
OSC is one of the parent for Tegra PMC clocks clk_out_1, clk_out_2,
and clk_out_3.
This patch adds Tegra OSC to clock lookup.
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra30 through Tegra210 has OSC_DIV2 and OSC_DIV4 fixed clocks
from the OSC pads.
This patch adds support for these clocks.
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
'A53_CORE' is just a mux and no need to be critical, being critical
will cause its parent clock always ON which does NOT make sense,
to make sure CPU's hardware clock source NOT being disabled during
clock tree setup, need to move the 'A53_SRC'/'A53_CORE' reparent
operations to after critical clock 'ARM_CLK' setup finished.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
'A53_CORE' is just a mux and no need to be critical, being critical
will cause its parent clock always ON which does NOT make sense,
to make sure CPU's hardware clock source NOT being disabled during
clock tree setup, need to move the 'A53_SRC'/'A53_CORE' reparent
operations to after critical clock 'ARM_CLK' setup finished.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
'A53_CORE' is just a mux and no need to be critical, being critical
will cause its parent clock always ON which does NOT make sense,
to make sure CPU's hardware clock source NOT being disabled during
clock tree setup, need to move the 'A53_SRC'/'A53_CORE' reparent
operations to after critical clock 'ARM_CLK' setup finished.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
'A53_CORE' is just a mux and no need to be critical, being critical
will cause its parent clock always ON which does NOT make sense,
to make sure CPU's hardware clock source NOT being disabled during
clock tree setup, need to move the 'A53_SRC'/'A53_CORE' reparent
operations to after critical clock 'ARM_CLK' setup finished.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
It is not good to use enable/disable for PLLv4 which needs time to
lock, because enable/disable is expected to be able run in
interrupt context. So use prepare/unprepare.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
pfdv2 is only used in i.MX7ULP. To get best pfd output, the i.MX7ULP
Datasheet defines two best PLL rate and pfd frac.
Per Datasheel
All PLLs on i.MX 7ULP either have VCO base frequency of
480 MHz or 528 MHz. So when determine best rate, we also
determine best parent rate which could match the requirement.
For some reason the current parent might not be 480MHz or 528MHz,
so we still take current parent rate as a choice.
And we also enable flag CLK_SET_RATE_PARENT to let parent rate
to be configured.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Per clk_ops, compared with round_rate, determine_rate could optionally
support the parent clock that should be used to provide the clock rate.
In this patch, the parent clock is just parent->rate as round_rate.
The following patch will calculate the best parent clock.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the clocks supported in global clock controller, which clock the
peripherals like BLSPs, SDCC, USB, MDSS etc. Register all the clocks
to the clock framework for the clients to be able to request for them.
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Signed-off-by: Venkata Narendra Kumar Gutta <vnkgutta@codeaurora.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lkml.kernel.org/r/20200224045003.3783838-6-vkoul@kernel.org
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Remove duplicate function for calculating the round rate of PLL and also
update the trion pll ops to use the common function.
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Signed-off-by: Venkata Narendra Kumar Gutta <vnkgutta@codeaurora.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lkml.kernel.org/r/20200224045003.3783838-3-vkoul@kernel.org
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The PLL run and standby modes are similar across the PLLs, thus rename
them to common names and update the use of these.
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Signed-off-by: Venkata Narendra Kumar Gutta <vnkgutta@codeaurora.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lkml.kernel.org/r/20200224045003.3783838-2-vkoul@kernel.org
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add rpm smd clocks, PMIC and bus clocks which are required on MSM8976,
MSM8956 (and APQ variants) for clients to vote on.
Signed-off-by: AngeloGioacchino Del Regno <kholk11@gmail.com>
Link: https://lkml.kernel.org/r/20191031112951.35850-2-kholk11@gmail.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The current implementation always uses rpmh_write_async, which doesn't
wait for completion. That's fine for disable requests since there's no
immediate need for the clocks and they can be disabled in the
background. However, for enable requests we need to ensure the clocks
are actually enabled before returning to the client. Otherwise, clients
can end up accessing their HW before the necessary clocks are enabled,
which can lead to bus errors.
Use the synchronous version of this API (rpmh_write) for enable requests
in the active set to ensure completion.
Completion isn't required for sleep/wake sets, since they don't take
effect until after we enter sleep. All rpmh requests are automatically
flushed prior to entering sleep.
Fixes: 9c7e47025a ("clk: qcom: clk-rpmh: Add QCOM RPMh clock driver")
Signed-off-by: Mike Tipton <mdtipton@codeaurora.org>
Link: https://lkml.kernel.org/r/20200215021232.1149-1-mdtipton@codeaurora.org
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
[sboyd@kernel.org: Reorg code a bit for readability, rename to 'wait' to
make local variable not conflict with completion.h mechanism]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
If the mmc clock has no rate, it can be assumed to be constant.
In such case, there is no measurable phase shift. Just return 0
in this case instead of returning an error.
Fixes: 2760878662 ("clk: Bail out when calculating phase fails during clk registration")
Tested-by: Markus Reichl <m.reichl@fivetechno.de>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lkml.kernel.org/r/20200303192956.64410-1-jbrunet@baylibre.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Commit 2760878662 ("clk: Bail out when calculating phase fails during
clk registration") introduced a check on error values at the time the
clock is registered to bail out when such an error occurs. However, it
doesn't check whether the returned value is positive which will happen
if the driver returns a non-zero phase. Since a phase is usually a
non-zero positive number this ends up returning something that isn't 0
to the caller of __clk_core_init(), making most clks fail to register
if they implement a phase clk op and return anything besides 0 for the
phase.
Fix this by returning the error if phase is less than zero or just
return zero if the phase is a positive number.
Fixes: 2760878662 ("clk: Bail out when calculating phase fails during clk registration")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lkml.kernel.org/r/20200225134248.919889-1-maxime@cerno.tech
Reported-by: "kernelci.org bot" <bot@kernelci.org>
[sboyd@kernel.org: Reword commit text to provide clarity]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
No need to initialize 'ret' in many functions, as it will get
the return value from function call, so remove the initializtion
of 'ret'.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
When pll type is invalid, ONLY output error message is NOT enough,
should return error immediately.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The A53 CCM clk root only accepts input up to 1GHz, CCM A53 root
signoff timing is 1Ghz, however the A53 core which sources from CCM
root could run above 1GHz which voilates the CCM.
There is a CORE_SEL slice before A53 core, we need configure the
CORE_SEL slice source from ARM PLL, not A53 CCM clk root.
The A53 CCM clk root should only be used when need to change ARM PLL
frequency.
Add arm_a53_core clk that could source from arm_a53_div and arm_pll_out.
Configure a53 ccm root sources from 800MHz sys pll
Configure a53 core sources from arm_pll_out
Mark arm_a53_core as critical clk
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The A53 CCM clk root only accepts input up to 1GHz, CCM A53 root
signoff timing is 1Ghz, however the A53 core which sources from CCM
root could run above 1GHz which voilates the CCM.
There is a CORE_SEL slice before A53 core, we need configure the
CORE_SEL slice source from ARM PLL, not A53 CCM clk root.
The A53 CCM clk root should only be used when need to change ARM PLL
frequency.
Add arm_a53_core clk that could source from arm_a53_div and arm_pll_out.
Configure a53 ccm root sources from 800MHz sys pll
Configure a53 core sources from arm_pll_out
Mark arm_a53_core as critical clk.
Fixes: 96d6392b54 ("clk: imx: Add support for i.MX8MN clock driver")
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The A53 CCM clk root only accepts input up to 1GHz, CCM A53 root
signoff timing is 1Ghz, however the A53 core which sources from CCM
root could run above 1GHz which voilates the CCM.
There is a CORE_SEL slice before A53 core, we need configure the
CORE_SEL slice source from ARM PLL, not A53 CCM clk root.
The A53 CCM clk root should only be used when need to change ARM PLL
frequency.
Add arm_a53_core clk that could source from arm_a53_div and arm_pll_out.
Configure a53 ccm root sources from 800MHz sys pll
Configure a53 core sources from arm_pll_out
Mark arm_a53_core as critical clock
Fixes: ba5625c3e2 ("clk: imx: Add clock driver support for imx8mm")
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The A53 CCM clk root only accepts input up to 1GHz, CCM A53 root
signoff timing is 1Ghz, however the A53 core which sources from CCM
root could run above 1GHz which violates the CCM.
There is a CORE_SEL slice before A53 core, we need to configure the
CORE_SEL slice source from ARM PLL, not A53 CCM clk root.
The A53 CCM clk root should only be used when need to change ARM PLL
frequency.
Add arm_a53_core clk that could source from arm_a53_div and arm_pll_out.
Configure a53 ccm root sources from 800MHz sys pll
Configure a53 core sources from arm_pll_out
Mark arm_a53_core as critical clock
Fixes: db27e40b27 ("clk: imx8mq: Add the missing ARM clock")
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
On i.MX8MP, internal HDMI 27M clock is actually 24MHz, so rename
the IMX8MP_CLK_HDMI_27M to IMX8MP_CLK_HDMI_24M.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
CONFIG_ARCH_R8A7795 was split in CONFIG_ARCH_R8A77950 and
CONFIG_ARCH_R8A77951 in commit b925adfceb ("soc: renesas: Add
ARCH_R8A7795[01] for existing R-Car H3"), so its users can be removed.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200218112525.5834-1-geert+renesas@glider.be
The aiu devices peripheral clocks needs the aiu and aiu_glue clocks to
operate. Reflect this hierarchy in the clock tree.
Fixes: e31a1900c1 ("meson: clk: Add support for clock gates")
Suggested-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
This adds the clocks used for the Amlogic G12A and compatible SoCs SPICC
controller to provide a more complete range of frequencies instead of the
SPICC internal divider over Xtal.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
There is nothing in use from init.h/of.h, remove them.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
There is nothing in use from init.h/of.h, remove them.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
slab.h is necessary and included indirectly by clkdev.h,
actually, there is nothing in use from clkdev.h, so just
include slab.h instead of clkdev.h.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Move SAM9X60's PLL register offsets to PMC header so that the
definitions would also be available from arch/arm/mach-at91/pm_suspend.S.
This is necessary to disable/enable PLLA for SAM9X60 on suspend/resume.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/1579522208-19523-7-git-send-email-claudiu.beznea@microchip.com
After finishing using device node got from of_find_compatible_node(),
of_node_put() needs to be called.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
After finishing using device node got from of_find_compatible_node(),
of_node_put() needs to be called.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
After finishing using device node got from of_find_compatible_node(),
of_node_put() needs to be called.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
After finishing using device node got from of_find_compatible_node(),
of_node_put() needs to be called.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
After finishing using device node got from of_find_compatible_node(),
of_node_put() needs to be called.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The i.MX7ULP clock driver is provider, NOT consumer, so clk-provider.h
should be used instead of clk.h.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
No need to initialize flags as 0, remove the initialization.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The i.MX8M SoCs clock driver are provider, NOT consumer, so clk-provider.h
should be used instead of clk.h.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add CLKO2 support, which is useful for debugging purposes.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The CLKO1 clock source select list is the following as per the i.MX8MM
Reference Manual (put in increasing order):
000 - 24M_REF_CLK
001 - SYSTEM_PLL1_CLK
010 - None
011 - SYSTEM_PLL1_DIV4
100 - AUDIO_PLL2_CLK
101 - SYSTEM_PLL2_DIV2
110 - VPU_PLL_CLK
111 - SYSTEM_PLL1_DIV10
Fix it accordingly.
Fixes: ba5625c3e2 ("clk: imx: Add clock driver support for imx8mm")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Use imx8m_clk_hw_composite_core to simplify code.
Add new definitions, and X_SRC/CG/DIV will be alias to the new
definitions for backwards compatibility
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Use imx8m_clk_hw_composite_core to simplify code.
Add new definitions, and X_SRC/CG/DIV will be alias to the new
definitions for backwards compatibility
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Use imx8m_clk_hw_composite_core to simplify code.
Add new definitions, and X_SRC/CG/DIV will be alias to the new
definitions for backwards compatibility
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
There are several clock slices, current composite code
only support bus/ip clock slices, it could not support core
slice.
So introduce a new API imx8m_clk_hw_composite_core to support
core slice. To core slice, post divider with 3 bits width and
no pre divider. Other fields are same as bus/ip slices.
Add a flag IMX_COMPOSITE_CORE for the usecase.
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add ocotp root clk, then when using nvmem to read fuse, clk
could be managed.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The aiu devices peripheral clocks needs the aiu and aiu_glue clocks to
operate. Reflect this hierarchy in the gxbb clock tree.
Fixes: 738f66d321 ("clk: gxbb: add AmLogic GXBB clk controller driver")
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Add the ACODEC clock gate to the gxl clk controller driver
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Add new frequency entries to pll1443x table to meet different
display settings requirement.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.mx8mn has support for clock gating the snvs module.
Add it into clock tree so that rtc-snvs driver could use it.
Note this will also be required in the snvs_pwrkey driver,
once support for clock management will be added.
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
do_div() macro to perform u64 division and guards against overflow if
the result is too large for the unsigned long return type.
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Link: https://lkml.kernel.org/r/20200114160726.19771-1-dinguyen@kernel.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The second line of the of_clk_detect_critical() function signature is
not indented according to coding style.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lkml.kernel.org/r/20191206133414.23925-1-geert+renesas@glider.be
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Consistent with other instances of samsung_clk_init, the check
if ctx is NULL is redundant. The function currently does not
return NULL.
Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Link: https://lkml.kernel.org/r/20200121233349.28627-1-pakki001@umn.edu
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
SAM9X60 USB clock may have up to 3 parents. Save the number of parents in
driver's data structure and validate against it when setting parent.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lkml.kernel.org/r/1579261009-4573-5-git-send-email-claudiu.beznea@microchip.com
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Use usbs_mask passed as argument. The usbs_mask is different for
SAM9X60.
Fixes: 2423eeaead ("clk: at91: usb: Add sam9x60 support")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lkml.kernel.org/r/1579261009-4573-4-git-send-email-claudiu.beznea@microchip.com
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
clk_hw_round_rate() may call round rate function of its parents. In case
of SAM9X60 two of USB parrents are PLLA and UPLL. These clocks are
controlled by clk-sam9x60-pll.c driver. The round rate function for this
driver is sam9x60_pll_round_rate() which call in turn
sam9x60_pll_get_best_div_mul(). In case the requested rate is not in the
proper range (rate < characteristics->output[0].min &&
rate > characteristics->output[0].max) the sam9x60_pll_round_rate() will
return a negative number to its caller (called by
clk_core_round_rate_nolock()). clk_hw_round_rate() will return zero in
case a negative number is returned by clk_core_round_rate_nolock(). With
this, the USB clock will continue its rate computation even caller of
clk_hw_round_rate() returned an error. With this, the USB clock on SAM9X60
may not chose the best parent. I detected this after a suspend/resume
cycle on SAM9X60.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lkml.kernel.org/r/1579261009-4573-2-git-send-email-claudiu.beznea@microchip.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
On sam9x60, there is not audio PLL and so I2S and classD have to use one
of the best matching parents for their generated clock.
Fixes: 01e2113de9 ("clk: at91: add sam9x60 pmc driver")
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Link: https://lkml.kernel.org/r/20200131115816.12483-1-codrin.ciubotariu@microchip.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Bail out of clk registration if we fail to get the phase for a clk that
has a clk_ops::get_phase() callback. Print a warning too so that driver
authors can easily figure out that some clk is unable to read back phase
information at boot.
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Heiko Stuebner <heiko@sntech.de>
Suggested-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lkml.kernel.org/r/20200205232802.29184-5-sboyd@kernel.org
Acked-by: Jerome Brunet <jbrunet@baylibre.com>
There's some confusion about when recalc is done for the rate and
accuracy clk consumer APIs in relation to the prepare lock being taken.
Oddly enough, we take the lock again in debugfs APIs so that we can call
the internal "clk_core" APIs to get these fields with any necessary
recalculations. Instead of having this confusion, let's introduce a
recalc variant of these two consumer APIs as internal helpers and call
them from the consumer APIs and the debugfs code so that we don't take
the lock more than once.
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lkml.kernel.org/r/20200205232802.29184-4-sboyd@kernel.org
Acked-by: Jerome Brunet <jbrunet@baylibre.com>
Some lines are getting long in this function. Let's move 'parent' up to
the top of the function and use it in many places whenever there is a
parent for a clk. This shortens some lines by avoiding core->parent->
indirections.
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lkml.kernel.org/r/20200205232802.29184-3-sboyd@kernel.org
Acked-by: Jerome Brunet <jbrunet@baylibre.com>
We don't check for errors from clk_ops::get_phase() before storing away
the result into the clk_core::phase member. This can lead to some fairly
confusing debugfs information if these ops do return an error. Let's
skip the store when this op fails to fix this. While we're here, move
the locking outside of clk_core_get_phase() to simplify callers from
the debugfs side.
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lkml.kernel.org/r/20200205232802.29184-2-sboyd@kernel.org
Acked-by: Jerome Brunet <jbrunet@baylibre.com>
I recently ran across this printk error message spewing in my logs
Call set rate on the PLL with rounded rates!
and I had no idea what clk that was or what rate was failing to round
properly. Make the printk more informative by telling us what went wrong
and also add the name of the clk that's failing to change rate.
Furthermore, update the other printks in this file with the clk name
each time so we know what clk we're talking about.
Cc: Taniya Das <tdas@codeaurora.org>
Cc: Venkata Narendra Kumar Gutta <vnkgutta@codeaurora.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lkml.kernel.org/r/20200205065421.9426-1-swboyd@chromium.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Most of the time the CPU should not be touching the GX domain on the
GPU except for a very special use case when the CPU needs to force the
GX headswitch off. Add the GX domain for that use case. As part of
this add a dummy enable function for the GX gdsc to simulate success
so that the pm_runtime reference counting is correct. This matches
what was done in sdm845 in commit 85a3d920d3 ("clk: qcom: Add a
dummy enable function for GX gdsc").
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lkml.kernel.org/r/1581307266-26989-2-git-send-email-tdas@codeaurora.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The disp_cc_mdss_rscc_ahb_clk is default enabled from hardware and thus
does not require to be marked CRITICAL. This which would allow the RCG to
be turned OFF when the display turns OFF and not blocking XO.
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Link: https://lkml.kernel.org/r/1581423236-21341-2-git-send-email-tdas@codeaurora.org
Fixes: dd3d066221 ("clk: qcom: Add display clock controller driver for SC7180")
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The clock disable signal for video_cc_vcodec0_core_clk is tied to
vcodec0_gdsc which is supported in the HW control mode. Thus turning off
the clock would be taken care automatically when the GDSC turns OFF by
hardware and clock driver does not require to poll on the CLK_OFF bit.
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Link: https://lkml.kernel.org/r/1581423235-21341-1-git-send-email-tdas@codeaurora.org
Fixes: 253dc75a0b ("clk: qcom: Add video clock controller driver for SC7180")
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
of_clk_get_parent_count() and of_clk_get_parent_name() never modify the
device nodes passed, so they can be const.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lkml.kernel.org/r/20200212094317.1150-1-geert+renesas@glider.be
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
R40 is actually very similar to A64, but it doesn't have mixer1 reset.
This means it's clocks and resets combination is unique and R40 specific
quirks are needed.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
A83T structures don't have clocks and reset for rotation core. Add them.
Fixes: 763c5bd045 ("clk: sunxi-ng: add support for DE2 CCU")
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Currently, V3s and H3 reuse A83T reset structure. However, A83T contains
additional core for rotation, which is not present in V3s and H3.
Make new reset structure for H3 and let V3s reuse it. A83T reset
structure will be amended in subsequent commit.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
DE3 documentation regarding presence of rotate core in H6 is a bit
confusing. Register descriptions mention bits for enabling rotate core
clocks and reset, but general overview doesn't list it as feature of H6
display engine, BSP kernel doesn't support it and there is no interrupt
listed for it. Manual poking registers also didn't reveal presence of
rotate core.
Let's assume there isn't any rotate core on H6 present and remove
related clocks. With that done, structures are same as those for H5, so
just reuse H5 structure.
Fixes: 56808da9f9 ("clk: sunxi-ng: Add support for H6 DE3 clocks")
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
A64 has rotation core which needs clocks and reset. Because there is no
appropriate structures available, make a separate, A64 specific
structures.
Fixes: cf4881c129 ("clk: sunxi-ng: fix the A64/H5 clock description of DE2 CCU")
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
H5 has less clocks and resets than A64. Currently that's not obvious
because A64 is missing rotation core related clocks and reset.
Split out H5 definition. A64 structures will be fixed in subsequent
commit.
Note that this patch depends on commit 19368d9974 ("clk: sunxi-ng:
add support for Allwinner H3 DE2 CCU") for the H3 clock list.
Fixes: 763c5bd045 ("clk: sunxi-ng: add support for DE2 CCU")
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
MBUS clock will be referenced in MBUS controller node.
Export it.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Describe the RPCSRC internal clock and the RPC[D2] clocks derived from
it, as well as the RPC-IF module clock, in the R-Car M3-N (R8A77965)
CPG/MSSR driver.
Inspired by commit 94e3935b57 ("clk: renesas: r8a77980: Add RPC clocks").
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Link: https://lore.kernel.org/r/20200203072901.31548-3-dirk.behme@de.bosch.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Describe the RPCSRC internal clock and the RPC[D2] clocks derived from
it, as well as the RPC-IF module clock, in the R-Car M3-W/M3-W+
(R8A7796) CPG/MSSR driver.
Inspired by commit 94e3935b57 ("clk: renesas: r8a77980: Add RPC clocks").
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Link: https://lore.kernel.org/r/20200203072901.31548-2-dirk.behme@de.bosch.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Describe the RPCSRC internal clock and the RPC[D2] clocks derived from
it, as well as the RPC-IF module clock, in the R-Car H3 (R8A7795)
CPG/MSSR driver.
Inspired by commit 94e3935b57 ("clk: renesas: r8a77980: Add RPC clocks").
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Link: https://lore.kernel.org/r/20200203072901.31548-1-dirk.behme@de.bosch.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add the CryptoCell module clocks and their parents for the CryptoCell
instances in the various Renesas R-Car Gen3 SoCs that do not have
support for them yet in their clock drivers (M3-W/W+, M3-N, E3, D3).
The R-Car H3 clock driver already supports these clocks.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200124133137.15921-1-geert+renesas@glider.be
This is some material that we picked up into our tree late, or that had
more complex dependencies on more than one topic branch that makes sense
to keep separately.
- TI support for secure accelerators and hwrng on OMAP4/5
- TI camera changes for dra7 and am437x and SGX improvement due to better
reset control support on am335x, am437x and dra7
- Davinci moves to proper clocksource on DM365, and regulator/audio
improvements for DM365 and DM644x eval boards
-----BEGIN PGP SIGNATURE-----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=R7GU
-----END PGP SIGNATURE-----
Merge tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC late updates from Olof Johansson:
"This is some material that we picked up into our tree late, or that
had more complex dependencies on more than one topic branch that makes
sense to keep separately.
- TI support for secure accelerators and hwrng on OMAP4/5
- TI camera changes for dra7 and am437x and SGX improvement due to
better reset control support on am335x, am437x and dra7
- Davinci moves to proper clocksource on DM365, and regulator/audio
improvements for DM365 and DM644x eval boards"
* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (32 commits)
ARM: dts: omap4-droid4: Enable hdq for droid4 ds250x 1-wire battery nvmem
ARM: dts: motorola-cpcap-mapphone: Configure calibration interrupt
ARM: dts: Configure interconnect target module for am437x sgx
ARM: dts: Configure sgx for dra7
ARM: dts: Configure rstctrl reset for am335x SGX
ARM: dts: dra7: Add ti-sysc node for VPE
ARM: dts: dra7: add vpe clkctrl node
ARM: dts: am43x-epos-evm: Add VPFE and OV2659 entries
ARM: dts: am437x-sk-evm: Add VPFE and OV2659 entries
ARM: dts: am43xx: add support for clkout1 clock
arm: dts: dra76-evm: Add CAL and OV5640 nodes
arm: dtsi: dra76x: Add CAL dtsi node
arm: dts: dra72-evm-common: Add entries for the CSI2 cameras
ARM: dts: DRA72: Add CAL dtsi node
ARM: dts: dra7-l4: Add ti-sysc node for CAM
ARM: OMAP: DRA7xx: Make CAM clock domain SWSUP only
ARM: dts: dra7: add cam clkctrl node
ARM: OMAP2+: Drop legacy platform data for omap4 des
ARM: OMAP2+: Drop legacy platform data for omap4 sham
ARM: OMAP2+: Drop legacy platform data for omap4 aes
...
Various driver updates for platforms:
- Nvidia: Fuse support for Tegra194, continued memory controller pieces
for Tegra30
- NXP/FSL: Refactorings of QuickEngine drivers to support ARM/ARM64/PPC
- NXP/FSL: i.MX8MP SoC driver pieces
- TI Keystone: ring accelerator driver
- Qualcomm: SCM driver cleanup/refactoring + support for new SoCs.
- Xilinx ZynqMP: feature checking interface for firmware. Mailbox
communication for power management
- Overall support patch set for cpuidle on more complex hierarchies
(PSCI-based)
+ Misc cleanups, refactorings of Marvell, TI, other platforms.
-----BEGIN PGP SIGNATURE-----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=ONtb
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC-related driver updates from Olof Johansson:
"Various driver updates for platforms:
- Nvidia: Fuse support for Tegra194, continued memory controller
pieces for Tegra30
- NXP/FSL: Refactorings of QuickEngine drivers to support
ARM/ARM64/PPC
- NXP/FSL: i.MX8MP SoC driver pieces
- TI Keystone: ring accelerator driver
- Qualcomm: SCM driver cleanup/refactoring + support for new SoCs.
- Xilinx ZynqMP: feature checking interface for firmware. Mailbox
communication for power management
- Overall support patch set for cpuidle on more complex hierarchies
(PSCI-based)
and misc cleanups, refactorings of Marvell, TI, other platforms"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (166 commits)
drivers: soc: xilinx: Use mailbox IPI callback
dt-bindings: power: reset: xilinx: Add bindings for ipi mailbox
drivers: soc: ti: knav_qmss_queue: Pass lockdep expression to RCU lists
MAINTAINERS: Add brcmstb PCIe controller entry
soc/tegra: fuse: Unmap registers once they are not needed anymore
soc/tegra: fuse: Correct straps' address for older Tegra124 device trees
soc/tegra: fuse: Warn if straps are not ready
soc/tegra: fuse: Cache values of straps and Chip ID registers
memory: tegra30-emc: Correct error message for timed out auto calibration
memory: tegra30-emc: Firm up hardware programming sequence
memory: tegra30-emc: Firm up suspend/resume sequence
soc/tegra: regulators: Do nothing if voltage is unchanged
memory: tegra: Correct reset value of xusb_hostr
soc/tegra: fuse: Add APB DMA dependency for Tegra20
bus: tegra-aconnect: Remove PM_CLK dependency
dt-bindings: mediatek: add MT6765 power dt-bindings
soc: mediatek: cmdq: delete not used define
memory: tegra: Add support for the Tegra194 memory controller
memory: tegra: Only include support for enabled SoCs
memory: tegra: Support DVFS on Tegra186 and later
...
- Make of_clk.h self contained
- Fix new qcom DT bindings that just merged to match the DTS files
- Fix qcom clk driver to properly detect DFS clk frequencies
- Fix the ls1028a driver to not deref a pointer before assigning it
-----BEGIN PGP SIGNATURE-----
iQJFBAABCAAvFiEE9L57QeeUxqYDyoaDrQKIl8bklSUFAl48WfERHHNib3lkQGtl
cm5lbC5vcmcACgkQrQKIl8bklSWtnw/+P0xw3S0Wdkr4UEkfCmSf8/JAP6xXc4Of
TFeJoXTCqqvgq66BpFVRMSPvA7jr2hx4siHBJbpXT4M+VpGhw5sRcEumQChHtZpX
WDSUszR86hxQCyq4ONdU0hQ6YfL/Erx14WqAK/DMHMLUtqIbSkfeVlZNTqpBHrBk
Nyx9S4rG0RerddmI1DPPikx3oPCwVxi+biqX3H+T1Ndsn2L/Iol+jerRfa9kbjRU
kaH/gXByikMKt+EdKlVLoCEl9jOC9gDu3MvM5ik01pFF5+SVeUD89wSDRHjuyVf/
mfag7xwXxxbjQNYJdEJu3keZslzezBUDY1DDnxIXstA7NhaQp2Jw6CX1S+S4KszR
Bh21okQGgSZUsnOVJmOOweqCPh8cvfyLb0sDjYlTgUog2QcQmBQbkTVqV5ZvvtF6
e5cdcxI7zHZQ5tszFXYk32GkXqN7QcucYy6HYbh6fcivkJOE5DozOUOP8DDkoP39
fWRCZiZLM3bWYx3he2MnMpZMxo7sLAMwpO2v+jxtqTZFVfvBPYaITuM08t+o9YH1
D+hIuSXoDKDzliQYEmo7p2k+JHstTw91sBuH9NRgNhcUZ1z/Fg8osfW7uBnuu5qv
vpK/xZJo8zJF3046xlnaRDz/oO2VKv6Wvq/04ayE087MEKps6OxE9AwxreB3brj1
kPWlYe0uexQ=
=fchl
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fixes from Stephen Boyd:
"A collection of fixes:
- Make of_clk.h self contained
- Fix new qcom DT bindings that just merged to match the DTS files
- Fix qcom clk driver to properly detect DFS clk frequencies
- Fix the ls1028a driver to not deref a pointer before assigning it"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
of: clk: Make <linux/of_clk.h> self-contained
clk: qcom: Use ARRAY_SIZE in videocc-sc7180 for parent clocks
clk: qcom: Get rid of the test clock for videocc-sc7180
dt-bindings: clock: Cleanup qcom,videocc bindings for sdm845/sc7180
clk: qcom: Use ARRAY_SIZE in gpucc-sc7180 for parent clocks
clk: qcom: Get rid of the test clock for gpucc-sc7180
dt-bindings: clock: Fix qcom,gpucc bindings for sdm845/sc7180/msm8998
clk: qcom: Use ARRAY_SIZE in dispcc-sc7180 for parent clocks
clk: qcom: Get rid of the test clock for dispcc-sc7180
clk: qcom: Get rid of fallback global names for dispcc-sc7180
dt-bindings: clock: Fix qcom,dispcc bindings for sdm845/sc7180
clk: qcom: rcg2: Don't crash if our parent can't be found; return an error
clk: ls1028a: fix a dereference of pointer 'parent' before a null check
dt-bindings: clk: qcom: Fix self-validation, split, and clean cruft
clk: qcom: Don't overwrite 'cfg' in clk_rcg2_dfs_populate_freq()
Merge more updates from Andrew Morton:
"The rest of MM and the rest of everything else: hotfixes, ipc, misc,
procfs, lib, cleanups, arm"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (67 commits)
ARM: dma-api: fix max_pfn off-by-one error in __dma_supported()
treewide: remove redundant IS_ERR() before error code check
include/linux/cpumask.h: don't calculate length of the input string
lib: new testcases for bitmap_parse{_user}
lib: rework bitmap_parse()
lib: make bitmap_parse_user a wrapper on bitmap_parse
lib: add test for bitmap_parse()
bitops: more BITS_TO_* macros
lib/string: add strnchrnul()
proc: convert everything to "struct proc_ops"
proc: decouple proc from VFS with "struct proc_ops"
asm-generic/tlb: provide MMU_GATHER_TABLE_FREE
asm-generic/tlb: rename HAVE_MMU_GATHER_NO_GATHER
asm-generic/tlb: rename HAVE_MMU_GATHER_PAGE_SIZE
asm-generic/tlb: rename HAVE_RCU_TABLE_FREE
asm-generic/tlb: add missing CONFIG symbol
asm-gemeric/tlb: remove stray function declarations
asm-generic/tlb: avoid potential double flush
mm/mmu_gather: invalidate TLB correctly on batch allocation failure and flush
powerpc/mmu_gather: enable RCU_TABLE_FREE even for !SMP case
...
In the new world input clocks should be matched by ".fw_name". sc7180
is new enough that no backward compatibility use of global names
should be needed. Remove it.
With a proper device tree and downstream display patches I have
verified booting a sc7180 up and seeing the display after this patch.
Fixes: dd3d066221 ("clk: qcom: Add display clock controller driver for SC7180")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lkml.kernel.org/r/20200203103049.v4.4.Ia3706a5d5add72e88dbff60fd13ec06bf7a2fd48@changeid
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
When I got my clock parenting slightly wrong I ended up with a crash
that looked like this:
Unable to handle kernel NULL pointer dereference at virtual
address 0000000000000000
...
pc : clk_hw_get_rate+0x14/0x44
...
Call trace:
clk_hw_get_rate+0x14/0x44
_freq_tbl_determine_rate+0x94/0xfc
clk_rcg2_determine_rate+0x2c/0x38
clk_core_determine_round_nolock+0x4c/0x88
clk_core_round_rate_nolock+0x6c/0xa8
clk_core_round_rate_nolock+0x9c/0xa8
clk_core_set_rate_nolock+0x70/0x180
clk_set_rate+0x3c/0x6c
of_clk_set_defaults+0x254/0x360
platform_drv_probe+0x28/0xb0
really_probe+0x120/0x2dc
driver_probe_device+0x64/0xfc
device_driver_attach+0x4c/0x6c
__driver_attach+0xac/0xc0
bus_for_each_dev+0x84/0xcc
driver_attach+0x2c/0x38
bus_add_driver+0xfc/0x1d0
driver_register+0x64/0xf8
__platform_driver_register+0x4c/0x58
msm_drm_register+0x5c/0x60
...
It turned out that clk_hw_get_parent_by_index() was returning NULL and
we weren't checking. Let's check it so that we don't crash.
Fixes: ac269395cd ("clk: qcom: Convert to clk_hw based provider APIs")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lkml.kernel.org/r/20200203103049.v4.1.I7487325fe8e701a68a07d3be8a6a4b571eca9cfa@changeid
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Currently the pointer 'parent' is being dereferenced before it is
being null checked. Fix this by performing the null check before
it is dereferenced.
Addresses-Coverity: ("Dereference before null check")
Fixes: d37010a3c1 ("clk: ls1028a: Add clock driver for Display output interface")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lkml.kernel.org/r/20200203223736.99645-1-colin.king@canonical.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
the normal collection of driver updates to support new SoCs, fix incorrect
data, and convert various drivers to clk_hw based APIs.
In the core, we allow clk_ops::init() to return an error code now so that we
can fail clk registration if the callback does something like fail to allocate
memory. We also add a new "terminate" clk_op so that things done in
clk_ops::init() can be undone, e.g. free memory. We also spit out a warning now
when critical clks fail to enable and we support changing clk rates and
enable/disable state through debugfs when developers compile the kernel
themselves.
On the driver front, we get support for what seems like a lot of Qualcomm and
NXP SoCs given that those vendors dominate the diffstat. There are a couple new
drivers for Xilinx and Amlogic SoCs too. The updates are all small things like
fixing the way glitch free muxes switch parents, avoiding div-by-zero problems,
or fixing data like parent names. See the updates section below for more
details.
Finally, the "basic" clk types have been converted to support specifying
parents with clk_hw pointers. This work includes an overhaul of the fixed-rate
clk type to be more modern by using clk_hw APIs.
Core:
- Let clk_ops::init() return an error code
- Add a clk_ops::terminate() callback to undo clk_ops::init()
- Warn about critical clks that fail to enable or prepare
- Support dangerous debugfs actions on clks with dead code
New Drivers:
- Support for Xilinx Versal platform clks
- Display clk controller on qcom sc7180
- Video clk controller on qcom sc7180
- Graphics clk controller on qcom sc7180
- CPU PLLs for qcom msm8916
- Move qcom msm8974 gfx3d clk to RPM control
- Display port clk support on qcom sdm845 SoCs
- Global clk controller on qcom ipq6018
- Add a driver for BCLK of Freescale SAI cores
- Add cam, vpe and sgx clock support for TI dra7
- Add aess clock support for TI omap5
- Enable clks for CPUfreq on Allwinner A64 SoCs
- Add Amlogic meson8b DDR clock controller
- Add input clocks to Amlogic meson8b controllers
- Add SPIBSC (SPI FLASH) clock on Renesas RZ/A2
- i.MX8MP clk driver support
Updates:
- Convert gpio, fixed-factor, mux, gate, divider basic clks to hw based APIs
- Detect more PRMCU variants in ux500 driver
- Adjust the composite clk type to new way of describing clk parents
- Fixes for clk controllers on qcom msm8998 SoCs
- Fix gmac main clock for TI dra7
- Move TI dra7-atl clock header to correct location
- Fix hidden node name dependency on TI clkctrl clocks
- Fix Amlogic meson8b mali clock update using the glitch free mux
- Fix Amlogic pll driver division by zero at init
- Prepare for split of Renesas R-Car H3 ES1.x and ES2.0+ config symbols
- Switch more i.MX clk drivers to clk_hw based APIs
- Disable non-functional divider between pll4_audio_div and
pll4_post_div on imx6q
- Fix watchdog2 clock name typo in imx7ulp clock driver
- Set CLK_GET_RATE_NOCACHE flag for DRAM related clocks on i.MX8M SoCs
- Suppress bind attrs for i.MX8M clock driver
- Add a big comment in imx8qxp-lpcg driver to tell why
devm_platform_ioremap_resource() shouldn't be used for the driver
- A correction on i.MX8MN usb1_ctrl parent clock setting
-----BEGIN PGP SIGNATURE-----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=UjXu
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"There are a few changes to the core framework this time around, in
addition to the normal collection of driver updates to support new
SoCs, fix incorrect data, and convert various drivers to clk_hw based
APIs.
In the core, we allow clk_ops::init() to return an error code now so
that we can fail clk registration if the callback does something like
fail to allocate memory. We also add a new "terminate" clk_op so that
things done in clk_ops::init() can be undone, e.g. free memory. We
also spit out a warning now when critical clks fail to enable and we
support changing clk rates and enable/disable state through debugfs
when developers compile the kernel themselves.
On the driver front, we get support for what seems like a lot of
Qualcomm and NXP SoCs given that those vendors dominate the diffstat.
There are a couple new drivers for Xilinx and Amlogic SoCs too. The
updates are all small things like fixing the way glitch free muxes
switch parents, avoiding div-by-zero problems, or fixing data like
parent names. See the updates section below for more details.
Finally, the "basic" clk types have been converted to support
specifying parents with clk_hw pointers. This work includes an
overhaul of the fixed-rate clk type to be more modern by using clk_hw
APIs.
Core:
- Let clk_ops::init() return an error code
- Add a clk_ops::terminate() callback to undo clk_ops::init()
- Warn about critical clks that fail to enable or prepare
- Support dangerous debugfs actions on clks with dead code
New Drivers:
- Support for Xilinx Versal platform clks
- Display clk controller on qcom sc7180
- Video clk controller on qcom sc7180
- Graphics clk controller on qcom sc7180
- CPU PLLs for qcom msm8916
- Move qcom msm8974 gfx3d clk to RPM control
- Display port clk support on qcom sdm845 SoCs
- Global clk controller on qcom ipq6018
- Add a driver for BCLK of Freescale SAI cores
- Add cam, vpe and sgx clock support for TI dra7
- Add aess clock support for TI omap5
- Enable clks for CPUfreq on Allwinner A64 SoCs
- Add Amlogic meson8b DDR clock controller
- Add input clocks to Amlogic meson8b controllers
- Add SPIBSC (SPI FLASH) clock on Renesas RZ/A2
- i.MX8MP clk driver support
Updates:
- Convert gpio, fixed-factor, mux, gate, divider basic clks to hw
based APIs
- Detect more PRMCU variants in ux500 driver
- Adjust the composite clk type to new way of describing clk parents
- Fixes for clk controllers on qcom msm8998 SoCs
- Fix gmac main clock for TI dra7
- Move TI dra7-atl clock header to correct location
- Fix hidden node name dependency on TI clkctrl clocks
- Fix Amlogic meson8b mali clock update using the glitch free mux
- Fix Amlogic pll driver division by zero at init
- Prepare for split of Renesas R-Car H3 ES1.x and ES2.0+ config
symbols
- Switch more i.MX clk drivers to clk_hw based APIs
- Disable non-functional divider between pll4_audio_div and
pll4_post_div on imx6q
- Fix watchdog2 clock name typo in imx7ulp clock driver
- Set CLK_GET_RATE_NOCACHE flag for DRAM related clocks on i.MX8M
SoCs
- Suppress bind attrs for i.MX8M clock driver
- Add a big comment in imx8qxp-lpcg driver to tell why
devm_platform_ioremap_resource() shouldn't be used for the driver
- A correction on i.MX8MN usb1_ctrl parent clock setting"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (140 commits)
dt/bindings: clk: fsl,plldig: Drop 'bindings' from schema id
clk: ls1028a: Fix warning on clamp() usage
clk: qoriq: add ls1088a hwaccel clocks support
clk: ls1028a: Add clock driver for Display output interface
dt/bindings: clk: Add YAML schemas for LS1028A Display Clock bindings
clk: fsl-sai: new driver
dt-bindings: clock: document the fsl-sai driver
clk: composite: add _register_composite_pdata() variants
clk: qcom: rpmh: Sort OF match table
dt-bindings: fix warnings in validation of qcom,gcc.yaml
dt-binding: fix compilation error of the example in qcom,gcc.yaml
clk: zynqmp: Add support for clock with CLK_DIVIDER_POWER_OF_TWO flag
clk: zynqmp: Fix divider calculation
clk: zynqmp: Add support for get max divider
clk: zynqmp: Warn user if clock user are more than allowed
clk: zynqmp: Extend driver for versal
dt-bindings: clock: Add bindings for versal clock driver
clk: ti: clkctrl: Fix hidden dependency to node name
clk: ti: add clkctrl data dra7 sgx
clk: ti: omap5: Add missing AESS clock
...
The DFS frequency table logic overwrites 'cfg' while detecting the
parent clk and then later on in clk_rcg2_dfs_populate_freq() we use that
same variable to figure out the mode of the clk, either MND or not. Add
a new variable to hold the parent clk bit so that 'cfg' is left
untouched for use later.
This fixes problems in detecting the supported frequencies for any clks
in DFS mode.
Fixes: cc4f6944d0 ("clk: qcom: Add support for RCG to register for DFS")
Reported-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lkml.kernel.org/r/20200128193329.45635-1-sboyd@kernel.org
Tested-by: Rajendra Nayak <rnayak@codeaurora.org>
These constants are used in clamp() with the value being clamped an
unsigned long. Make them unsigned long defines so that clamp() doesn't
complain about comparing different types.
In file included from include/linux/list.h:9,
from include/linux/kobject.h:19,
from include/linux/of.h:17,
from include/linux/clk-provider.h:9,
from drivers/clk/clk-plldig.c:8:
drivers/clk/clk-plldig.c: In function 'plldig_determine_rate':
include/linux/kernel.h:835:29: warning: comparison of distinct pointer types lacks a cast
835 | (!!(sizeof((typeof(x) *)1 == (typeof(y) *)1)))
|
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Wen He <wen.he_1@nxp.com>
Fixes: d37010a3c1 ("clk: ls1028a: Add clock driver for Display output interface")
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lkml.kernel.org/r/20200203052507.93215-1-sboyd@kernel.org
- Add support for ROHM BD71828 PMICs and GPIOs
- Add support for Qualcomm Aqstic Audio Codecs WCD9340 and WCD9341
- New Device Support
- Add support for BD71828 to BD70528 RTC driver
- Add support for Intel's Jasper Lake to LPSS PCI
- New Functionality
- Add support for Power Key to ROHM BD71828
- Add support for Clocks to ROHM BD71828
- Add support for GPIOs to Dialog DA9062
- Add support for USB PD Notify to ChromiumOS EC
- Allow callers to specify args when requesting regmap lookup; syscon
- Fix-ups
- Improve error handling and sanity checking; atmel-hlcdc, dln2
- Device Tree support/documentation; bd71828, da9062, xylon,logicvc,
ab8500, max14577, atmel-usart
- Match devices using platform IDs; bd7xxxx
- Refactor BD718x7 regulator component; bd718x7-regulator
- Use standard interfaces/helpers; syscon, sm501
- Trivial (whitespace, spelling, etc); ab8500-core, Kconfig
- Remove unused code; db8500-prcmu, tqmx86
- Wait until boot has finished before accessing registers; madera-core
- Provide missing register value defaults; cs47l15-tables
- Allow more time for hardware to reset; madera-core
- Bug Fixes
- Fix erroneous register values; rohm-bd70528
- Fix register volatility; axp20x, rn5t618
- Fix Kconfig dependencies; MFD_MAX77650
- Fix incorrect compatible string; da9062-core
- Fix syscon_regmap_lookup_by_phandle_args() stub; syscon
-----BEGIN PGP SIGNATURE-----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=t4+B
-----END PGP SIGNATURE-----
Merge tag 'mfd-next-5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"New Drivers:
- Add support for ROHM BD71828 PMICs and GPIOs
- Add support for Qualcomm Aqstic Audio Codecs WCD9340 and WCD9341
New Device Support:
- Add support for BD71828 to BD70528 RTC driver
- Add support for Intel's Jasper Lake to LPSS PCI
New Functionality:
- Add support for Power Key to ROHM BD71828
- Add support for Clocks to ROHM BD71828
- Add support for GPIOs to Dialog DA9062
- Add support for USB PD Notify to ChromiumOS EC
- Allow callers to specify args when requesting regmap lookup; syscon
Fix-ups:
- Improve error handling and sanity checking; atmel-hlcdc, dln2
- Device Tree support/documentation; bd71828, da9062, xylon,logicvc,
ab8500, max14577, atmel-usart
- Match devices using platform IDs; bd7xxxx
- Refactor BD718x7 regulator component; bd718x7-regulator
- Use standard interfaces/helpers; syscon, sm501
- Trivial (whitespace, spelling, etc); ab8500-core, Kconfig
- Remove unused code; db8500-prcmu, tqmx86
- Wait until boot has finished before accessing registers;
madera-core
- Provide missing register value defaults; cs47l15-tables
- Allow more time for hardware to reset; madera-core
Bug Fixes:
- Fix erroneous register values; rohm-bd70528
- Fix register volatility; axp20x, rn5t618
- Fix Kconfig dependencies; MFD_MAX77650
- Fix incorrect compatible string; da9062-core
- Fix syscon_regmap_lookup_by_phandle_args() stub; syscon"
* tag 'mfd-next-5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (41 commits)
mfd: syscon: Fix syscon_regmap_lookup_by_phandle_args() dummy
mfd: wcd934x: Add support to wcd9340/wcd9341 codec
mfd: syscon: Add arguments support for syscon reference
mfd: rn5t618: Mark ADC control register volatile
dt-bindings: atmel-usart: Add microchip,sam9x60-{usart, dbgu}
dt-bindings: atmel-usart: Remove wildcard
mfd: cros_ec: Add cros-usbpd-notify subdevice
mfd: da9062: Fix watchdog compatible string
mfd: madera: Allow more time for hardware reset
mfd: cs47l15: Add missing register default
mfd: madera: Wait for boot done before accessing any other registers
mfd: Kconfig: Rename Samsung to lowercase
mfd: tqmx86: remove set but not used variable 'i2c_ien'
mfd: dbx500-prcmu: Drop DSI pll clock functions
mfd: dbx500-prcmu: Drop set_display_clocks()
mfd: max77650: Select REGMAP_IRQ in Kconfig
mfd: axp20x: Mark AXP20X_VBUS_IPSOUT_MGMT as volatile
mfd: ab8500: Fix ab8500-clk typo
mfd: intel-lpss: Add Intel Jasper Lake PCI IDs
dt-bindings: mfd: max14577: Add reference to max14040_battery.txt descriptions
...
- Support for Xilinx Versal platform clks
- Display clk controller on qcom sc7180
- Video clk controller on qcom sc7180
- Graphics clk controller on qcom sc7180
- CPU PLLs for qcom msm8916
- Fixes for clk controllers on qcom msm8998 SoCs
- Move qcom msm8974 gfx3d clk to RPM control
- Display port clk support on qcom sdm845 SoCs
- Global clk controller on qcom ipq6018
- Adjust composite clk to new way of describing clk parents
- Add a driver for BCLK of Freescale SAI cores
* clk-imx: (32 commits)
clk: imx: Add support for i.MX8MP clock driver
dt-bindings: imx: Add clock binding doc for i.MX8MP
clk: imx: gate4: Switch imx_clk_gate4_flags() to clk_hw based API
clk: imx: imx8mq: Switch to clk_hw based API
clk: imx: imx8mm: Switch to clk_hw based API
clk: imx: imx8mn: Switch to clk_hw based API
clk: imx: Remove __init for imx_obtain_fixed_clk_hw() API
clk: imx: gate3: Switch to clk_hw based API
clk: imx: add hw API imx_clk_hw_mux2_flags
clk: imx: add imx_unregister_hw_clocks
clk: imx: clk-composite-8m: Switch to clk_hw based API
clk: imx: clk-pll14xx: Switch to clk_hw based API
clk: imx7up: Rename the clks to hws
clk: imx: Rename the imx_clk_divider_gate to imply it's clk_hw based
clk: imx: Rename the imx_clk_pfdv2 to imply it's clk_hw based
clk: imx: Rename the imx_clk_pllv4 to imply it's clk_hw based
clk: imx: Rename sccg and frac pll register to suggest clk_hw
clk: imx: imx7ulp composite: Rename to show is clk_hw based
clk: imx: pllv2: Switch to clk_hw based API
clk: imx: pllv1: Switch to clk_hw based API
...
* clk-ti:
clk: ti: clkctrl: Fix hidden dependency to node name
clk: ti: add clkctrl data dra7 sgx
clk: ti: omap5: Add missing AESS clock
clk: ti: dra7: fix parent for gmac_clkctrl
clk: ti: dra7: add vpe clkctrl data
clk: ti: dra7: add cam clkctrl data
dt-bindings: clock: Move ti-dra7-atl.h to dt-bindings/clock
* clk-xilinx:
clk: zynqmp: Add support for clock with CLK_DIVIDER_POWER_OF_TWO flag
clk: zynqmp: Fix divider calculation
clk: zynqmp: Add support for get max divider
clk: zynqmp: Warn user if clock user are more than allowed
clk: zynqmp: Extend driver for versal
dt-bindings: clock: Add bindings for versal clock driver
* clk-nvidia:
clk: tegra20/30: Explicitly set parent clock for Video Decoder
clk: tegra20/30: Don't pre-initialize displays parent clock
clk: tegra: divider: Check UART's divider enable-bit state on rate's recalculation
clk: tegra: clk-dfll: Remove call to pm_runtime_irq_safe()
clk: tegra: Mark fuse clock as critical
* clk-qcom: (35 commits)
clk: qcom: rpmh: Sort OF match table
dt-bindings: fix warnings in validation of qcom,gcc.yaml
dt-binding: fix compilation error of the example in qcom,gcc.yaml
clk: qcom: Add ipq6018 Global Clock Controller support
clk: qcom: Add DT bindings for ipq6018 gcc clock controller
clk: qcom: gcc-msm8996: Fix parent for CLKREF clocks
clk: qcom: rpmh: Add IPA clock for SC7180
clk: qcom: rpmh: skip undefined clocks when registering
clk: qcom: Add video clock controller driver for SC7180
dt-bindings: clock: Introduce SC7180 QCOM Video clock bindings
dt-bindings: clock: Add YAML schemas for the QCOM VIDEOCC clock bindings
clk: qcom: Add graphics clock controller driver for SC7180
dt-bindings: clock: Introduce SC7180 QCOM Graphics clock bindings
dt-bindings: clock: Add YAML schemas for the QCOM GPUCC clock bindings
clk: qcom: apcs-msm8916: use clk_parent_data to specify the parent
clk: qcom: Add display clock controller driver for SC7180
dt-bindings: clock: Introduce QCOM sc7180 display clock bindings
dt-bindings: clock: Add YAML schemas for the QCOM DISPCC clock bindings
clk: qcom: clk-alpha-pll: Add support for Fabia PLL calibration
clk: qcom: alpha-pll: Remove useless read from set rate
...
* clk-freescale:
clk: fsl-sai: new driver
dt-bindings: clock: document the fsl-sai driver
clk: composite: add _register_composite_pdata() variants
* clk-qoriq:
clk: qoriq: add ls1088a hwaccel clocks support
clk: ls1028a: Add clock driver for Display output interface
dt/bindings: clk: Add YAML schemas for LS1028A Display Clock bindings
- Support dangerous debugfs actions on clks with dead code
- Convert gpio, fixed-factor, mux, gate, divider basic clks to hw based APIs
* clk-debugfs-danger:
clk: Add support for setting clk_rate via debugfs
* clk-basic-hw:
clk: divider: Add support for specifying parents via DT/pointers
clk: gate: Add support for specifying parents via DT/pointers
clk: mux: Add support for specifying parents via DT/pointers
clk: asm9260: Use parent accuracy in fixed rate clk
clk: fixed-rate: Document that accuracy isn't a rate
clk: fixed-rate: Add clk flags for parent accuracy
clk: fixed-rate: Add support for specifying parents via DT/pointers
clk: fixed-rate: Document accuracy member
clk: fixed-rate: Move to_clk_fixed_rate() to C file
clk: fixed-rate: Remove clk_register_fixed_rate_with_accuracy()
clk: fixed-rate: Convert to clk_hw based APIs
clk: gpio: Use DT way of specifying parents
* clk-renesas:
clk: renesas: Prepare for split of R-Car H3 config symbol
dt-bindings: clock: renesas: cpg-mssr: Fix r8a774b1 typo
clk: renesas: r7s9210: Add SPIBSC clock
clk: renesas: rcar-gen3: Allow changing the RPC[D2] clocks
clk: renesas: Remove use of ARCH_R8A7796
clk: renesas: rcar-gen2: Change multipliers and dividers to u8
* clk-amlogic:
clk: clarify that clk_set_rate() does updates from top to bottom
clk: meson: meson8b: make the CCF use the glitch-free mali mux
clk: meson: pll: Fix by 0 division in __pll_params_to_rate()
clk: meson: g12a: fix missing uart2 in regmap table
clk: meson: meson8b: use of_clk_hw_register to register the clocks
clk: meson: meson8b: don't register the XTAL clock when provided via OF
clk: meson: meson8b: change references to the XTAL clock to use [fw_]name
clk: meson: meson8b: use clk_hw_set_parent in the CPU clock notifier
clk: meson: add a driver for the Meson8/8b/8m2 DDR clock controller
dt-bindings: clock: meson8b: add the clock inputs
dt-bindings: clock: add the Amlogic Meson8 DDR clock controller binding
* clk-allwinner:
clk: sunxi: a23/a33: Export the MIPI PLL
clk: sunxi: a31: Export the MIPI PLL
clk: sunxi-ng: a64: export CLK_CPUX clock for DVFS
clk: sunxi-ng: add mux and pll notifiers for A64 CPU clock
clk: sunxi-ng: r40: Export MBUS clock
clk: sunxi: use of_device_get_match_data
- Let clk_ops::init() return an error code
- Add a clk_ops::terminate() callback to undo clk_ops::init()
* clk-init-allocation:
clk: add terminate callback to clk_ops
clk: let init callback return an error code
clk: actually call the clock init before any other callback of the clock
* clk-unused:
clk: bm1800: Remove set but not used variable 'fref'
* clk-register-dt-node-better:
clk: Use parent node pointer during registration if necessary
Add clock driver for QorIQ LS1028A Display output interfaces(LCD, DPHY),
as implemented in TSMC CLN28HPM PLL, this PLL supports the programmable
integer division and range of the display output pixel clock's 27-594MHz.
Signed-off-by: Wen He <wen.he_1@nxp.com>
Signed-off-by: Michael Walle <michael@walle.cc>
Link: https://lkml.kernel.org/r/20191213083402.35678-2-wen.he_1@nxp.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
With this driver it is possible to use the BCLK pin of the SAI module as
a generic clock output. This is esp. useful if you want to drive a clock
to an audio codec. Because the output only allows integer divider values
the audio codec needs an integrated PLL.
Signed-off-by: Michael Walle <michael@walle.cc>
Link: https://lkml.kernel.org/r/20200102231101.11834-3-michael@walle.cc
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add support for the new way of specifying the clock parents. Add the
two new functions
clk_hw_register_composite_pdata()
clk_register_composite_pdata()
to let the driver provide parent_data instead of the parent_names.
Signed-off-by: Michael Walle <michael@walle.cc>
Link: https://lkml.kernel.org/r/20200102231101.11834-1-michael@walle.cc
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The Si5341 and Si5340 have multiple input clock options. So far, the driver
only supported the XTAL input, this adds support for the three external
clock inputs as well.
If the clock chip isn't programmed at boot, the driver will default to the
XTAL input as before. If there is no "xtal" clock input available, it will
pick the first connected input (e.g. "in0") as the input clock for the PLL.
One can use clock-assigned-parents to select a particular clock as input.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Link: https://lkml.kernel.org/r/20200107075340.14528-1-mike.looijmans@topic.nl
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
- remove ioremap_nocache given that is is equivalent to
ioremap everywhere
-----BEGIN PGP SIGNATURE-----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=TUCJ
-----END PGP SIGNATURE-----
Merge tag 'ioremap-5.6' of git://git.infradead.org/users/hch/ioremap
Pull ioremap updates from Christoph Hellwig:
"Remove the ioremap_nocache API (plus wrappers) that are always
identical to ioremap"
* tag 'ioremap-5.6' of git://git.infradead.org/users/hch/ioremap:
remove ioremap_nocache and devm_ioremap_nocache
MIPS: define ioremap_nocache to ioremap
BD71828GW is a single-chip power management IC for battery-powered portable
devices. Add support for controlling BD71828 clk using bd718x7 driver.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Thanks to Stephen Boyd I today learned we can use platform_device_id
to do device and module matching for MFD sub-devices!
Do device matching using the platform_device_id instead of using
explicit module_aliases to load modules and custom parent-data field
to do module loading and sub-device matching.
Cc: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Existing clock divider functions is not checking for
base of divider. So, if any clock divider is power of 2
then clock rate calculation will be wrong.
Add support to calculate divider value for the clocks
with CLK_DIVIDER_POWER_OF_TWO flag.
Signed-off-by: Tejas Patel <tejas.patel@xilinx.com>
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Link: https://lkml.kernel.org/r/1575527759-26452-7-git-send-email-rajan.vaja@xilinx.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
zynqmp_clk_divider_round_rate() returns actual divider value
after calculating from parent rate and desired rate, even though
that rate is not supported by single divider of hardware. It is
also possible that such divisor value can be achieved through 2
different dividers. As, Linux tries to set such divisor value(out
of range) in single divider set divider is getting failed.
Fix the same by computing best possible combination of two
divisors which provides more accurate clock rate.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Tejas Patel <tejas.patel@xilinx.com>
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Link: https://lkml.kernel.org/r/1575527759-26452-6-git-send-email-rajan.vaja@xilinx.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
To achieve best possible rate, maximum limit of divider is required
while computation. Get maximum supported divisor from firmware. To
maintain backward compatibility assign maximum possible value(0xFFFF)
if query for max divisor is not successful.
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Link: https://lkml.kernel.org/r/1575527759-26452-5-git-send-email-rajan.vaja@xilinx.com
Acked-by: Michal Simek <michal.simek@xilinx.com>
[sboyd@kernel.org: Remove else return and just return]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Warn user if clock is used by more than allowed devices.
This check is done by firmware and returns respective
error code. Upon receiving error code for excessive user,
warn user for the same.
This change is done to restrict VPLL use count. It is
assumed that VPLL is used by one user only.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Link: https://lkml.kernel.org/r/1575527759-26452-4-git-send-email-rajan.vaja@xilinx.com
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add Versal compatible string to support Versal
binding.
Signed-off-by: Jolly Shah <jolly.shah@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Link: https://lkml.kernel.org/r/1575527759-26452-3-git-send-email-rajan.vaja@xilinx.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Rajan Vaja