Impact: reduce kernel size a bit, address sparse warning
Addresses the problem pointed out by this sparse warning:
arch/x86/kernel/pci-swiotlb.c:53:20: warning: symbol 'swiotlb_dma_ops' was not declared. Should it be static?
For x86: swiotlb_dma_ops can be static, because it's not used outside
of pci-swiotlb.c
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Acked-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
LKML-Reference: <1239558861.3938.2.camel@localhost.localdomain>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
/dev/mem mmap code was doing memtype reserve/free for a while now.
Recently we added memtype tracking in remap_pfn_range, and /dev/mem mmap
uses it indirectly. So, we don't need seperate tracking in /dev/mem code
any more. That means another ~100 lines of code removed :-).
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
LKML-Reference: <20090409212709.085210000@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Fix pat_x_mtrr_type() to use UC_MINUS when the mtrr type return UC. This
is to be consistent with ioremap() and ioremap_nocache() which uses
UC_MINUS.
Consolidate the code such that reserve_memtype() also uses
pat_x_mtrr_type() when the caller doesn't specify any special attribute
(non WB attribute).
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
LKML-Reference: <20090409212708.939936000@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
As per SDM, there should not be any aliasing of a WC with any cacheable
type across CPUs. That is if one CPU is changing the identity map
memtype to _WC, no other CPU at the time of this change should not have a
TLB for this page that carries a WB attribute. SDM suggests to make the
page not present. But for that we will have to handle any page faults
that can potentially happen due to these pages being not present.
Other way to deal with this without having any WB mapping is to change
the page first to UC and then to WC. This ensures that we meet the SDM
requirement of no cacheable alais to WC page. This also has same or
lower overhead than marking the page not present and making it present
later.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
LKML-Reference: <20090409212708.797481000@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Handle faults and do proper cleanups in set_memory_*() functions. In
some cases, these functions were not doing proper free on failure paths.
With the changes to tracking memtype of RAM pages in struct page instead
of pat list, we do not need the changes in commits c5e147. This patch
reverts that change.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
LKML-Reference: <20090409212708.653222000@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
To be free of aliasing due to races, set_memory_* interfaces should
follow ordering of reserving, changing memtype to UC/WC, changing
memtype back to WB followed by free.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
LKML-Reference: <20090409212708.512280000@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Change the identity mapping with the requested attribute first, before
we setup the virtual memory mapping with the new requested attribute.
This makes sure that there is no window when identity map'ed attribute
may disagree with ioremap range on the attribute type.
This also avoids doing cpa on the ioremap'ed address twice (first in
ioremap_page_range and then in ioremap_change_attr using vaddr), and
should improve ioremap performance a bit.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
LKML-Reference: <20090409212708.373330000@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
While better than get_user_pages(), the usage of gupf(),
especially the return values and the fact that it can
potentially only partially pin the range, warranted some
documentation.
Signed-off-by: Andy Grover <andy.grover@oracle.com>
Cc: npiggin@suse.de
Cc: akpm@linux-foundation.org
LKML-Reference: <1239320729-3262-1-git-send-email-andy.grover@oracle.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
To simplify level irq migration in the presence of interrupt-remapping,
Suresh used a virtual vector (io-apic pin number) to eliminate io-apic
RTE modification. Level triggered interrupt will appear as an edge to
the local apic cpu but still as level to the IO-APIC. So in addition to
do the local apic EOI, it still needs to do IO-APIC directed EOI to clear
the remote IRR bit in the IO-APIC RTE. Pls refer to Suresh's patch for
more details (commit 0280f7c416).
Now interrupt remapping is decoupled from x2apic, it also needs to do the
directed EOI for apic. Otherwise, apic interrupts won't work correctly.
Signed-off-by: Weidong Han <weidong.han@intel.com>
Cc: iommu@lists.linux-foundation.org
Cc: Weidong Han <weidong.han@intel.com>
Cc: suresh.b.siddha@intel.com
Cc: dwmw2@infradead.org
Cc: allen.m.kay@intel.com
LKML-Reference: <1239355037-22856-1-git-send-email-weidong.han@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
It seems by mistake these files got execute permissions so removing it.
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
LKML-Reference: <1239211186.9037.2.camel@ht.satnam>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Now /proc/interrupts of tip tree has new counters:
PLT: Platform interrupts
Format change of output, as like that by commit:
commit 7a81d9a7da
x86: smarten /proc/interrupts output
should be applied to these new counters too.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Cc: Jan Beulich <jbeulich@novell.com>
LKML-Reference: <49C98DEA.8060208@jp.fujitsu.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: restore old behavior
for flat and phys_flat
Signed-off-by: Yinhai Lu <yinghai@kernel.org.
LKML-Reference: <49DCBBF1.8080903@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'tracing-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
branch tracer, intel-iommu: fix build with CONFIG_BRANCH_TRACER=y
branch tracer: Fix for enabling branch profiling makes sparse unusable
ftrace: Correct a text align for event format output
Update /debug/tracing/README
tracing/ftrace: alloc the started cpumask for the trace file
tracing, x86: remove duplicated #include
ftrace: Add check of sched_stopped for probe_sched_wakeup
function-graph: add proper initialization for init task
tracing/ftrace: fix missing include string.h
tracing: fix incorrect return type of ns2usecs()
tracing: remove CALLER_ADDR2 from wakeup tracer
blktrace: fix pdu_len when tracing packet command requests
blktrace: small cleanup in blk_msg_write()
blktrace: NUL-terminate user space messages
tracing: move scripts/trace/power.pl to scripts/tracing/power.pl
Impact: Fixes these modes on at least one system
The rewrite of the setup code into C resequenced the font setting and
register reprogramming phases of configuring nonstandard VGA modes
which use 480 scan lines in text mode. However, there exists at least
one board (Micro-Star MS-7383 version 2.0) on which this resequencing
causes an unusable display.
Revert to the original sequencing: set up 480-line mode, install the
font, and then adjust the vertical end register appropriately.
This failure was masked by the fact that the 480-line setup was broken
until checkin 5f64135612 (therefore this
is not a -stable candidate bug fix.)
Reported-by: Andi Kleen <andi@firstfloor.org>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
* 'i2c-for-2630-v2' of git://aeryn.fluff.org.uk/bjdooks/linux:
i2c: imx: Make disable_delay a per-device variable
i2c: xtensa s6000 i2c driver
powerpc/85xx: i2c-mpc: use new I2C bindings for the Socates board
i2c: i2c-mpc: make I2C bus speed configurable
i2c: i2c-mpc: use dev based printout function
i2c: i2c-mpc: various coding style fixes
i2c: imx: Add missing request_mem_region in probe()
i2c: i2c-s3c2410: Initialise Samsung I2C controller early
i2c-s3c2410: Simplify bus frequency calculation
i2c-s3c2410: sda_delay should be in ns, not clock ticks
i2c: iMX/MXC support
Both software emulated and hardware based CTS and RTS are enabled in
serial driver.
The CTS RTS PIN connection on BF548 UART port is defined as a modem
device not as a host device. In order to test it under Linux, please
nake a cross UART cable to exchange CTS and RTS signal.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Only the CTS bit is affected.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use the new general RS485 Linux data structure (introduced by Alan with
commit number c26c56c0f4) in the Cris
architecture too (currently, Cris still uses the old private data
structure instead of the new one).
Signed-off-by: Claudio Scordino <claudio@evidence.eu.com>
Tested-by: Hinko Kocevar <hinko.kocevar@cetrtapot.si>
Tested-by: Janez Cufer <janez.cufer@cetrtapot.si>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace all DMA_24BIT_MASK macro with DMA_BIT_MASK(24)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace all DMA_32BIT_MASK macro with DMA_BIT_MASK(32)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace all DMA_40BIT_MASK macro with DMA_BIT_MASK(40)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace all DMA_64BIT_MASK macro with DMA_BIT_MASK(64)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Most SPI peripherals use GPIOs as their chip selects, introduce .gpio_cs
for this.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
1. Rewrite of the non-dma data transfer functions to use only ONE mode
of TIMOD (TIMOD=0x1). With TIMOD=0, it was not possible to set the TX
bit pattern. So the TDBR = 0xFFFF inside the read calls won't work.
2. Clear SPI_RDBR before reading and before duplex transfer.
Otherwise the garbage data in RDBR will get read. Since mmc_spi uses a
lot of duplex transfers, this is the main cause of mmc_spi failure.
3. Poll RXS for transfer completion. Polling SPIF or TXS cannot
guarantee transfer completion. This may interrupt a transfer before it
is finished. Also this may leave garbage data in buffer and affect
next transfer.
[Yi Li <yi.li@analog.com>: add a field "u16 idle_tx_val" in "struct
bfin5xx_spi_chip" to specify the value to transmit if no TX value
is supplied.]
Signed-off-by: Wolfgang Muees <wolfgang.mues@auerswald.de>
Signed-off-by: Yi Li <yi.li@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for GPIO controlled SPI Chip Selects. To make use of this
feature, set chip_select = 0 and add a proper cs_gpio to your
controller_data.
struct spi_board_info
.chip_select = 0
struct bfin5xx_spi_chip
.cs_gpio = GPIO_P###
There are various SPI devices that require SPI MODE_0, and need to have
the Chip Selects asserted during the entire transfer. Consider using
SPI_MODE_3 (SPI_CPHA | SPI_CPOL) if your device allows it.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix erroneous SPI Clock divisor calculation. Make sure SPI_BAUD is always
>= 2. Writing a value of 0 or 1 to the SPI_BAUD register disables the
serial clock.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (28 commits)
powerpc: Fix oops when loading modules
powerpc: Wire up preadv and pwritev
powerpc/ftrace: Fix printf format warning
powerpc/ftrace: Fix #if that should be #ifdef
powerpc: Fix ptrace compat wrapper for FPU register access
powerpc: Print information about mapping hw irqs to virtual irqs
powerpc: Correct dependency of KEXEC
powerpc: Disable VSX or current process in giveup_fpu/altivec
powerpc/pseries: Enable relay in pseries_defconfig
powerpc/pseries: Fix ibm,client-architecture comment
powerpc/pseries: Scan for all events in rtasd
powerpc/pseries: Add dispatch dispersion statistics
powerpc: Clean up some prom printouts
powerpc: Print progress of ibm,client-architecture method
powerpc: Remove duplicated #include's
powerpc/pmac: Fix internal modem IRQ on Wallstreet PowerBook
powerpc/wdrtas: Update wdrtas_get_interval to use rtas_data_buf
fsl-diu-fb: Pass the proper device for dma mapping routines
powerpc/pq2fads: Update device tree for use with device-tree-aware u-boot.
cpm_uart: Disable CPM udbg when re-initing CPM uart, even if not the console.
...
Preserve I2C clock settings for the Socrates MPC8544 board.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The platform data for the i2c-s3c2410 driver used to allow a min,
max and desired frequency for the I2C bus. This patch reduces it
to simply a desired frequency ceiling and corrects all the uses
of the platform data appropriately.
This means, for example, that on a system with a 66MHz fclk, a
request for 100KHz will achieve 65KHz which is safe and
acceptable, rather than 378KHz which it would have achieved
without this change.
Signed-off-by: Simtec Linux Team <linux@simtec.co.uk>
Signed-off-by: Daniel Silverstone <dsilvers@simtec.co.uk>
[ben-linux@fluff.org: tidy subject and description]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The sda_delay field should be specified in ns, not in clock ticks
as when using cpufreq we could be changing the bus rate.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Implementation of I2C Adapter/Algorithm Driver for I2C Bus integrated
in Freescale's i.MX/MXC processors.
Signed-off-by: Darius Augulis <augulis.darius@gmail.com>
Tested-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This build failure:
| drivers/pci/dmar.c:47: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘dmar_tbl_size’
| drivers/pci/dmar.c:62: warning: ‘struct acpi_dmar_device_scope’ declared inside parameter list
| drivers/pci/dmar.c:62: warning: its scope is only this definition or declaration, which is probably not what you want
Triggers due to this commit:
d0b03bd: x2apic/intr-remap: decouple interrupt remapping from x2apic
Which exposed a pre-existing but dormant fragility of the 'select X86_X2APIC'
it moved around and turned that fragility into a build failure.
Replace it with a proper 'depends on' construct.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
LKML-Reference: <1239084280.22733.404.camel@macbook.infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This fixes a problem reported by Sean MacLennan where loading any
module would cause an oops. We weren't marking the pages containing
the module text as having hardware execute permission, due to a bug
introduced in commit 8d1cf34e ("powerpc/mm: Tweak PTE bit combination
definitions"), hence trying to execute the module text caused an
exception on processors that support hardware execute permission.
This adds _PAGE_HWEXEC to the definitions of PAGE_KERNEL_X and
PAGE_KERNEL_ROX to fix this problem.
Reported-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
[paulus@samba.org: changed to use syscall numbers 320 and 321 since
perf_counters is currently using 319.]
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
'tramp' is an unsigned long, so print it with %lx.
Fixes the following build warning:
arch/powerpc/kernel/ftrace.c:291: error: format ‘%x’ expects type ‘unsigned int’, but argument 2 has type ‘long unsigned int’
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Commit bb7253403f ("powerpc64,
ftrace: save toc only on modules for function graph"), added an
#if CONFIG_PPC64. This changes it to #ifdef.
Fixes the following warning on 32-bit builds:
arch/powerpc/kernel/ftrace.c:562:5: error: "CONFIG_PPC64" is not defined
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The ptrace compat wrapper mishandles access to the fpu registers. The
PTRACE_PEEKUSR and PTRACE_POKEUSR requests miscalculate the index into
the fpr array due to the broken FPINDEX macro. The
PPC_PTRACE_PEEKUSR_3264 request needs to use the same formula that the
native ptrace interface uses when operating on the register number (as
opposed to the 4-byte offset). The PPC_PTRACE_POKEUSR_3264 request
didn't take TS_FPRWIDTH into account.
Signed-off-by: Andreas Schwab <schwab@linux-m68k.org>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The irq remapping layer seems to cause some confusion when people
see a different irq number in /proc/interrupts vs the one they
request in their driver or DTS.
So have the irq remapping layer print out a message when we map an
irq. The message is only printed the first time the irq is mapped,
and it's KERN_DEBUG so most people won't see it.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
commit 28794d34ec ("powerpc/kconfig: Kill
PPC_MULTIPLATFORM") broke KEXEC, by making it dependent on BOOK3S, while it
should be PPC_BOOK3S.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
When we call giveup_fpu, we need to need to turn off VSX for the
current process. If we don't, on return to userspace it may execute a
VSX instruction before the next FP instruction, and not have its
register state refreshed correctly from the thread_struct. Ditto for
altivec.
This caused a bug where an unaligned lfs or stfs results in
fix_alignment calling giveup_fpu so it can use the FPRs (in order to
do a single <-> double conversion), and then returning to userspace
with FP off but VSX on. Then if a VSX instruction is executed, before
another FP instruction, it will proceed without another exception and
hence have the incorrect register state for VSX registers 0-31.
lfs unaligned <- alignment exception turns FP off but leaves VSX on
VSX instruction <- no exception since VSX on, hence we get the
wrong VSX register values for VSX registers 0-31,
which overlap the FPRs.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Enable relay in pseries config, ppc64_defconfig had it enabled but pseries
did not.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Instead of checking for known events, pass in all 1s so we handle future
event types. We were currently missing the IO event type.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
PHYP tells us how often a shared processor dispatch changed physical cpus.
This can highlight performance problems caused by the hypervisor.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Make all messages consistent, some have spaces before the "...", some do not.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The ibm,client-architecture method will often cause a reconfiguration reboot.
When this happens the last thing we see is:
Hypertas detected, assuming LPAR !
Which doesn't explain what just happened. Wrap the ibm,client-architecture
so it's clear what is going on:
Calling ibm,client-architecture... done
In order to maintain the law of conservation of screen real estate, downgrade
two other messages to debug.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Jaswinder Singh Rajput