Factor out the code which sends out the register read/write opcodes
to the switch, since the code differs in single bit between read and
write.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Cc: Woojung Huh <Woojung.Huh@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The indirect function call to dev->dev_ops->get_port_addr() is expensive
especially if called for every single register access, and only returns
the value of PORT_CTRL_ADDR() macro. Use PORT_CTRL_ADDR() macro directly
instead.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Cc: Woojung Huh <Woojung.Huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These functions are only used by the KSZ9477 code, move them from
the header into that code. Note that these functions will be soon
replaced by regmap equivalents.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Cc: Woojung Huh <Woojung.Huh@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The functions in the header file are static, and the header file is
included from single C file, just inline the code into the C file.
The bonus is that it's easier to spot further content to clean up.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Cc: Woojung Huh <Woojung.Huh@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
These functions and callbacks are never used, remove them.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Cc: Woojung Huh <Woojung.Huh@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
These functions and callbacks are never used, remove them.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Cc: Woojung Huh <Woojung.Huh@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Igor Russkikh says:
====================
net: aquantia: implement vlan offloads
This patchset introduces hardware VLAN offload support and also does some
maintenance: we replace driver version with uts version string, add
documentation file for atlantic driver, and update maintainers
adding Igor as a maintainer.
v3: shuffle doc sections, per Andrew's comments
v2: updates in doc, gpl spdx tag cleanup
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
set_features should update flags and reinit hardware if
vlan offload settings were changed.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Tested-by: Nikita Danilov <ndanilov@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update datapath by adding logic related to hardware assisted
vlan strip/insert behaviour.
Tested-by: Nikita Danilov <ndanilov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Updating features and vlan_features with vlan HW offload.
Added vlan_tag fields to rx/tx ring_buff to track vlan related data.
Tested-by: Nikita Danilov <ndanilov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Register declaration macros required to work with vlan offload mode.
Tested-by: Nikita Danilov <ndanilov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It was noticed some files had -or-later, however overall driver has
-only license. Clean this up.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Aquantia is resposible now for all new features and bugfixes.
Reflect that in MAINTAINERS.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Document contains configuration options description,
details and examples of driver various settings.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As it was discussed some time previously, driver is better to
report kernel version string, as it in a best way identifies
the codebase.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2019-06-26
This series contains updates to ixgbe and i40e only.
Mauro S. M. Rodrigues update the ixgbe driver to handle transceivers who
comply with SFF-8472 but do not implement the Digital Diagnostic
Monitoring (DOM) interface. Update the driver to check the necessary
bits to see if DOM is implemented before trying to read the additional
256 bytes in the EEPROM for DOM data.
Young Xiao fixes a potential divide by zero issue in ixgbe driver.
Aleksandr fixes i40e to recognize 2.5 and 5.0 GbE link speeds so that it
is not reported as "Unknown bps". Fixes the driver to read the firmware
LLDP agent status during DCB initialization, and to properly log the
LLDP agent status to help with debugging when DCB fails to initialize.
Martyna fixes i40e for the missing supported and advertised link modes
information in ethtool.
Jake fixes a function header comment that was incorrect for a PTP
function in i40e.
Maciej fixes an issue for i40e when a XDP program is loaded the
descriptor count gets reset to the default value, resolve the issue by
making the current descriptor count persistent across resets.
Alice corrects a copyright date which she found to be incorrect.
Piotr adds a log entry when the traffic class 0 is added or deleted, which
was not being logged previously.
Gustavo A. R. Silva updates i40e to use struct_size() where possible.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann says:
====================
s390/qeth: updates 2019-06-27
please apply another round of qeth updates for net-next.
This completes the conversion of the control path to use dynamically
allocated cmd buffers, along with some fine-tuning for the route
validation fix that recently went into -net.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The cast type currently gets selected in .ndo_start_xmit, and is then
piped through several layers until it's stored into the HW header.
Push the selection down into qeth_l?_fill_header() to (1) reduce the
number of xmit-wide parameters, and (2) merge the two route validation
checks into just one.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As follow-up to commit 0cd6783d3c ("s390/qeth: check dst entry before use"),
consolidate the dst_check() logic into a single helper and add a wrapper
around the cast type selection.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use napi_gro_receive() to pass up all types of packets that a L3 device
may receive.
1) For proper L2 packets received by the IQD sniffer, this is the
obvious thing to do.
2) For af_iucv (which doesn't provide a GRO assist), the GRO code will
transparently fall back to netif_receive_skb(). So there's no need to
special-case this traffic in our code.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
De-duplicate the pm callback implementations from the two sub-drivers,
replacing them with core helpers that delegate to the .set_online and
.set_offline callbacks.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Apply some cleanups to qeth_snmp_command() and its callback:
1. when accessing the user data, use the proper struct instead of
hard-coded offsets. Also copy the request data straight into the
allocated cmd, skipping the extra memdup_user() to a tmp buffer.
2. capping the request length is no longer needed, the same check gets
applied at a base level in qeth_alloc_cmd().
3. clean up some duplicated (and misindented) trace statements.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that all cmds are dynamically allocated, the code for static cmd
buffers can go away entirely. Resulting in a nice reduction of
code/data size & complexity, while removing the risk that
qeth_clear_cmd_buffers() releases cmds that are still in-flight.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The base MPC cmds are the last remaining user of the static cmd buffers.
Port them over to use dynamic allocation, and stop backing the write
channel's cmd buffers with pages.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The VNICC code is somewhat quirky in that it defers the whole cmd setup
to a common helper qeth_l2_vnicc_request(). Some of the cmd specifics
are then passed in via parameter, while others are simply hard-coded.
Split the whole machinery up into the usual format: one helper that
allocates the cmd & fills in the common fields, while all the cmd
originators take care of their sub-cmd type specific work.
This makes it much easier to calculate the cmd's precise length, and
reduces code complexity.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new wrapper that allocates DIAG cmds of the right size, and fills
in the common fields.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch converts the adapter, assist and bridgeport cmd paths to
dynamic allocation. Most of the work is about re-organizing the cmd
headers, calculating the correct cmd length, and filling in the right
value in the sub-cmd's length field.
Since we now also set the correct length for cmds that are not reflected
by a fixed struct (ie SNMP), we can remove the work-around from
qeth_snmp_command().
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For code that uses qeth_send_simple_setassparms_prot(), we currently
can't differentiate whether the cmd should contain (1) no parameter, or
(2) a 4-byte parameter with value 0.
At the moment this doesn't cause any trouble. But when using dynamically
allocated cmds, we need to know whether to allocate & transmit an
additional 4 bytes of zeroes.
So instead of the raw parameter value, pass a parameter pointer
(or NULL) to qeth_send_simple_setassparms_prot().
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch reduces the usage of the write channel's static cmd buffers,
by dynamically allocating all simple IPA cmds (eg. STARTLAN, SETVMAC).
It also converts the OSN path.
Doing so requires some changes to how we calculate the cmd length.
Currently when building IPA cmds, we're quite generous in how much data
we send down to the device (basically the size of the biggest cmd we
know). This is no real concern at the moment, since the static cmd
buffers are backed with zeroed pages. But for dynamic allocations, the
exact length matters. So this patch also adds the needed length
calculations to each cmd path.
Commands that have multiple subtypes (eg. SETADP) of differing length
will be converted with follow-up patches.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are common steps when releasing an accepted or unaccepted socket.
Move this code into a common routine.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Westphal says:
====================
net: ipv4: fix circular-list infinite loop
Tariq and Ran reported a regression caused by net-next commit
2638eb8b50 ("net: ipv4: provide __rcu annotation for ifa_list").
This happens when net.ipv4.conf.$dev.promote_secondaries sysctl is
enabled -- we can arrange for ifa->next to point at ifa, so next
process that tries to walk the list loops forever.
Fix this and extend rtnetlink.sh with a small test case for this.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This exercises the 'promote_secondaries' code path.
Without previous fix, this triggers infinite loop/soft lockup:
ifconfig process spinning at 100%, never to return.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
secondary address promotion causes infinite loop -- it arranges
for ifa->ifa_next to point back to itself.
Problem is that 'prev_prom' and 'last_prim' might point at the same entry,
so 'last_sec' pointer must be obtained after prev_prom->next update.
Fixes: 2638eb8b50 ("net: ipv4: provide __rcu annotation for ifa_list")
Reported-by: Ran Rozenstein <ranro@mellanox.com>
Reported-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
When parsing an ethtool_rx_flow_spec, users can specify an ethernet flow
which could contain matches based on the ethernet header, such as the
MAC address, the VLAN tag or the ethertype.
ETHER_FLOW uses the src and dst ethernet addresses, along with the
ethertype as keys. Matches based on the vlan tag are also possible, but
they are specified using the special FLOW_EXT flag.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Acked-by: Pablo Neira Ayuso <pablo@gnumonks.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Palmer Dabbelt says:
====================
net: macb: Fix compilation on systems without COMMON_CLK, v2
Our patch to add support for the FU540-C000 broke compilation on at
least powerpc allyesconfig, which was found as part of the linux-next
build regression tests. This must have somehow slipped through the
cracks, as the patch has been reverted in linux-next for a while now.
This patch applies on top of the offending commit, which is the only one
I've even tried it on as I'm not sure how this subsystem makes it to
Linus.
This patch set fixes the issue by adding a dependency of COMMON_CLK to
the MACB Kconfig entry, which avoids the build failure by disabling MACB
on systems where it wouldn't compile. All known users of MACB have
COMMON_CLK, so this shouldn't cause any issues. This is a significantly
simpler approach than disabling just the FU540-C000 support.
I've also included a second patch to indicate this is a driver for a
Cadence device that was originally written by an engineer at Atmel. The
only relation is that I stumbled across it when writing the first patch.
Changes since v1 <20190624061603.1704-1-palmer@sifive.com>:
* Disable MACB on systems without COMMON_CLK, instead of just disabling
the FU540-C000 support on these systems.
* Update the commit message to reflect the driver was written by Atmel.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The help text makes it look like NET_VENDOR_CADENCE enables support for
Atmel devices, when in reality it's a driver written by Atmel that
supports Cadence devices. This may confuse users that have this device
on a non-Atmel SoC.
The fix is just s/Atmel/Cadence/, but I did go and re-wrap the Kconfig
help text as that change caused it to go over 80 characters.
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit c218ad5590 ("macb: Add support for SiFive FU540-C000") added a
dependency on the common clock framework to the macb driver, but didn't
express that dependency in Kconfig. As a result macb now fails to
compile on systems without COMMON_CLK, which specifically causes a build
failure on powerpc allyesconfig.
This patch adds the dependency, which results in the macb driver no
longer being selectable on systems without the common clock framework.
All known systems that have this device already support the common clock
framework, so this should not cause trouble for any uses. Supporting
both the FU540-C000 and systems without COMMON_CLK is quite ugly.
I've build tested this on powerpc allyesconfig and RISC-V defconfig
(which selects MACB), but I have not even booted the resulting kernels.
Fixes: c218ad5590 ("macb: Add support for SiFive FU540-C000")
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The longstanding prohibition against using 0.0.0.0/8 dates back
to two issues with the early internet.
There was an interoperability problem with BSD 4.2 in 1984, fixed in
BSD 4.3 in 1986. BSD 4.2 has long since been retired.
Secondly, addresses of the form 0.x.y.z were initially defined only as
a source address in an ICMP datagram, indicating "node number x.y.z on
this IPv4 network", by nodes that know their address on their local
network, but do not yet know their network prefix, in RFC0792 (page
19). This usage of 0.x.y.z was later repealed in RFC1122 (section
3.2.2.7), because the original ICMP-based mechanism for learning the
network prefix was unworkable on many networks such as Ethernet (which
have longer addresses that would not fit into the 24 "node number"
bits). Modern networks use reverse ARP (RFC0903) or BOOTP (RFC0951)
or DHCP (RFC2131) to find their full 32-bit address and CIDR netmask
(and other parameters such as default gateways). 0.x.y.z has had
16,777,215 addresses in 0.0.0.0/8 space left unused and reserved for
future use, since 1989.
This patch allows for these 16m new IPv4 addresses to appear within
a box or on the wire. Layer 2 switches don't care.
0.0.0.0/32 is still prohibited, of course.
Signed-off-by: Dave Taht <dave.taht@gmail.com>
Signed-off-by: John Gilmore <gnu@toad.com>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dst_default_metrics has all of the metrics initialized to 0, so nothing
will be added to the skb in rtnetlink_put_metrics. Avoid the loop if
metrics is from dst_default_metrics.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Puranjay Mohan says:
====================
net: fddi: skfp: Use PCI generic definitions instead of private duplicates
This patch series removes the private duplicates of PCI definitions in
favour of generic definitions defined in pci_regs.h.
This driver only uses some of the generic PCI definitons,
which are included from pci_regs.h and thier private versions
are removed from skfbi.h with all other private defines.
The skfbi.h defines PCI_REV_ID and other private defines with different
names, these are renamed to Generic PCI names to make them
compatible with defines in pci_regs.h.
All unused defines are removed from skfbi.h.
Changes in v5:
Removed unused PCI definitions which were left in v4
Changes in v4:
Removed unused PCI definitions which were left in v3
Changes in v3:
Renamed all local PCI definitions to Generic names.
Corrected coding style mistakes.
Changes in v2:
Converted individual patches to a series.
Made sure that individual patches build correctly
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unused private PCI definitions from skfbi.h because generic PCI
symbols are already included from pci_regs.h.
Signed-off-by: Puranjay Mohan <puranjay12@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Include the uapi/linux/pci_regs.h header file which contains the generic
PCI defines.
Signed-off-by: Puranjay Mohan <puranjay12@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename the PCI_REV_ID and other local defines to Generic PCI define names
in skfbi.h and drvfbi.c to make it compatible with the pci_regs.h.
Signed-off-by: Puranjay Mohan <puranjay12@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
First set of patches for 5.3, but not that many patches this time.
This pull request fails to compile with the tip tree due to
ktime_get_boot_ns() API changes there. It should be easy for Linus to
fix it in p54 driver once he pulls this, an example resolution here:
https://lkml.kernel.org/r/20190625160432.533aa140@canb.auug.org.au
Major changes:
airo
* switch to use skcipher interface
p54
* support boottime in scan results
rtw88
* add fast xmit support
* add random mac address on scan support
rt2x00
* add software watchdog to detect hangs, it's disabled by default
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJdE5OGAAoJEG4XJFUm622bWCoH/1bLdkTYOkSatXxpHn2cVRvA
SrQ+ZSfOWJe5d0B+9HWhO5r+Savuu+IrgcC6vSIBBVglF5Tf6F0DAxHVrIwc9MSY
QUv4f1suqeH0ipUEBWJXoDXM2OEShvw5WCuY0ZnYw2hZRI7Sb5nqwJEUH57BtBCX
tFW22Ax3ZFTmCfexFgiwEjmtEx6HHz/nleYLMt9gg7X1Twug+QmhEsNw/27PfvMx
RyVyCJ1UvW2x4GHqDRlGxQoh7FlMvuVe/v/VcjGp2Fp8s7GS0xUyA11svGBFpdnT
K94Y3LOcTSdBQwScbn6O2v6EybB9PZYhg6rckwbMgIN2pkkWqXnh5avru4U0T9k=
=yq6Q
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2019-06-26' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valu says:
====================
wireless-drivers-next patches for 5.3
First set of patches for 5.3, but not that many patches this time.
This pull request fails to compile with the tip tree due to
ktime_get_boot_ns() API changes there. It should be easy for Linus to
fix it in p54 driver once he pulls this, an example resolution here:
https://lkml.kernel.org/r/20190625160432.533aa140@canb.auug.org.au
Major changes:
airo
* switch to use skcipher interface
p54
* support boottime in scan results
rtw88
* add fast xmit support
* add random mac address on scan support
rt2x00
* add software watchdog to detect hangs, it's disabled by default
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct virtchnl_iwarp_qvlist_info {
...
struct virtchnl_iwarp_qv_info qv_info[1];
};
size = sizeof(struct virtchnl_iwarp_qvlist_info) + (sizeof(struct virtchnl_iwarp_qv_info) * count;
instance = kzalloc(size, GFP_KERNEL);
and
struct virtchnl_vf_resource {
...
struct virtchnl_vsi_resource vsi_res[1];
};
size = sizeof(struct virtchnl_vf_resource) + sizeof(struct virtchnl_vsi_resource) * count;
instance = kzalloc(size, GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
instance = kzalloc(struct_size(instance, qv_info, count), GFP_KERNEL);
and
instance = kzalloc(struct_size(instance, vsi_res, count), GFP_KERNEL);
Notice that, in the first case above, variable size is not necessary, hence it
is removed.
This code was detected with the help of Coccinelle.
Signed-off-by: "Gustavo A. R. Silva" <gustavo@embeddedor.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
It was found that the string that prints our copyright was
not up to date. Updating to reflect our copyright.
Signed-off-by: Alice Michael <alice.michael@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Changing descriptor count via 'ethtool -G' is not persistent across resets.
When PF reset occurs, we roll back to the default value of vsi->num_desc,
which is used then in i40e_alloc_rings to set descriptor count. XDP does a
PF reset so when user has changed the descriptor count and load XDP
program, the default count will be back there.
To fix this:
* introduce new VSI members - num_tx_desc and num_rx_desc in favour of
num_desc
* set them in i40e_set_ringparam to user's values
* set them to default values in i40e_set_num_rings_in_vsi only when they
don't have previous values
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes reading f/w LLDP agent status at DCB init time.
It's done by removing direct NVM reading in i40e_update_dcb_config()
and checking whether f/w LLDP agent is disabled via
I40E_FLAG_DISABLE_FW_LLDP flag in i40e_init_pf_dcb(). The function
i40e_update_dcb_config() in i40e_main.c is a temporary solution which
will be later renamed to i40e_init_dcb() in the i40e_dcb module. Also
logging was extended to make visible if f/w LLDP agent is running or not
and always log a message when DCB was not initialized. Without this
patch for new f/w versions f/w LLDP agent status was always read
from NVM as disabled and DCB initialization failed without
clear reason in logs.
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Generate log entry when TC0 is created or deleted.
Log entry is generated during main VSI setup.
Before there was no log info about adding or deleting TC0.
Signed-off-by: Piotr Kwapulinski <piotr.kwapulinski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Marek Vasut