After commit 33e4f80ee6 ("ACPI / PM: Ignore spurious SCI wakeups
from suspend-to-idle") the "noirq" phases of device suspend and
resume may run for multiple times during suspend-to-idle, if there
are spurious system wakeup events while suspended. However, this
is complicated and fragile and actually unnecessary.
The main reason for doing this is that on some systems the EC may
signal system wakeup events (power button events, for example) as
well as events that should not cause the system to resume (spurious
system wakeup events). Thus, in order to determine whether or not
a given event signaled by the EC while suspended is a proper system
wakeup one, the EC GPE needs to be dispatched and to start with that
was achieved by allowing the ACPI SCI action handler to run, which
was only possible after calling resume_device_irqs().
However, dispatching the EC GPE this way turned out to take too much
time in some cases and some EC events might be missed due to that, so
commit 68e2201185 ("ACPI: EC: Dispatch the EC GPE directly on
s2idle wake") started to dispatch the EC GPE right after a wakeup
event has been detected, so in fact the full ACPI SCI action handler
doesn't need to run any more to deal with the wakeups coming from the
EC.
Use this observation to simplify the suspend-to-idle control flow
so that the "noirq" phases of device suspend and resume are each
run only once in every suspend-to-idle cycle, which is reported to
significantly reduce power drawn by some systems when suspended to
idle (by allowing them to reach a deep platform-wide low-power state
through the suspend-to-idle flow). [What appears to happen is that
the "noirq" resume of devices after a spurious EC wakeup brings some
devices into a state in which they prevent the platform from reaching
the deep low-power state going forward, even after a subsequent
"noirq" suspend phase, and on some systems the EC triggers such
wakeups already when the "noirq" suspend of devices is running for
the first time in the given suspend/resume cycle, so the platform
cannot reach the deep low-power state at all.]
First, make acpi_s2idle_wake() use the acpi_ec_dispatch_gpe() return
value to determine whether or not the wakeup may have been triggered
by the EC (in which case the system wakeup is canceled and ACPI
events are processed in order to determine whether or not the event
is a proper system wakeup one) and use rearm_wake_irq() (introduced
by a previous change) in it to rearm the ACPI SCI for system wakeup
detection in case the system will remain suspended.
Second, drop acpi_s2idle_sync(), which is not needed any more, and
the corresponding global platform suspend-to-idle callback.
Next, drop the pm_wakeup_pending() check (which is an optimization
only) from __device_suspend_noirq() to prevent it from returning
errors on system wakeups occurring before the "noirq" phase of
device suspend is complete (as in the case of suspend-to-idle it is
not known whether or not these wakeups are suprious at that point),
in order to avoid having to carry out a "noirq" resume of devices
on a spurious system wakeup.
Finally, change the code flow in s2idle_loop() to (1) run the
"noirq" suspend of devices once before starting the loop, (2) check
for spurious EC wakeups (via the platform ->wake callback) for the
first time before calling s2idle_enter(), and (3) run the "noirq"
resume of devices once after leaving the loop.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
The role of the s2idle_wakeup variable is to cause
acpi_pm_wakeup_event() and acpi_pm_notify_handler() to
increment pm_abort_suspend and trigger a wakeup from
suspend-to-idle in case the ACPI SCI wakeup was canceled
by acpi_s2idle_wake().
However, for this purpose it need not be set in acpi_s2idle_wake()
and cleared in acpi_s2idle_sync(), respectively. In fact, it
may be set as early as in acpi_s2idle_prepare() and cleared as
late as in acpi_s2idle_restore(), so do that to allow subsequent
changes to be simpler.
This change is not expected to alter functionality.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
* acpi-pm:
ACPI: PM: Make acpi_sleep_state_supported() non-static
ACPI: PM: Allow transitions to D0 to occur in special cases
ACPI: PM: Avoid evaluating _PS3 on transitions from D3hot to D3cold
ACPI / sleep: Switch to use acpi_dev_get_first_match_dev()
ACPI / LPIT: Correct LPIT end address for lpit_process()
* pm-pci:
ACPI: PM: Unexport acpi_device_get_power()
PCI: PM/ACPI: Refresh all stale power state data in pci_pm_complete()
PCI / ACPI: Add _PR0 dependent devices
ACPI / PM: Introduce concept of a _PR0 dependent device
PCI / ACPI: Use cached ACPI device state to get PCI device power state
PCI: Do not poll for PME if the device is in D3cold
PCI: Add missing link delays required by the PCIe spec
PCI: PM: Replace pci_dev_keep_suspended() with two functions
PCI: PM: Avoid resuming devices in D3hot during system suspend
With some upcoming patches to save/restore the Hyper-V drivers related
states, a Linux VM running on Hyper-V will be able to hibernate. When
a Linux VM hibernates, unluckily we must disable the memory hot-add/remove
and balloon up/down capabilities in the hv_balloon driver
(drivers/hv/hv_balloon.c), because these can not really work according to
the design of the related back-end driver on the host.
By default, Hyper-V does not enable the virtual ACPI S4 state for a VM;
on recent Hyper-V hosts, the administrator is able to enable the virtual
ACPI S4 state for a VM, so we hope to use the presence of the virtual ACPI
S4 state as a hint for hv_balloon to disable the aforementioned
capabilities. In this way, hibernation will work more reliably, from the
user's perspective.
By marking acpi_sleep_state_supported() non-static, we'll be able to
implement a hv_is_hibernation_supported() API in the always-built-in
module arch/x86/hyperv/hv_init.c, and the API will be called by hv_balloon.
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Switch the acpi_pm_finish() to use acpi_dev_get_first_match_dev() instead of
custom approach.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Based on 1 normalized pattern(s):
this file is released under the gplv2
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 68 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Armijn Hemel <armijn@tjaldur.nl>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190531190114.292346262@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On systems with ACPI platform firmware the last stage of hibernation
is analogous to system suspend to S3 (suspend-to-RAM), so it should
be handled analogously. In particular, pm_suspend_via_firmware()
should return 'true' in that stage to let the callers of it know that
control will be passed to the platform firmware going forward, so
pm_set_suspend_via_firmware() needs to be called then in analogy with
acpi_suspend_begin().
However, the platform hibernation ->begin() callback is invoked
during the "freeze" transition (before creating a snapshot image of
system memory) as well as during the "hibernate" transition which is
the last stage of it and pm_set_suspend_via_firmware() should be
invoked by that callback in the latter stage only.
In order to implement that redefine the hibernation ->begin()
callback to take a pm_message_t argument to indicate which stage
of hibernation is taking place and rework acpi_hibernation_begin()
and acpi_hibernation_begin_old() to take it into account as needed.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
I noticed that recently multiple systems (chromebooks) couldn't wake
from S0ix using LID or Keyboard after updating to a newer kernel. I
bisected and it turned up commit f941d3e41d ("ACPI: EC / PM: Disable
non-wakeup GPEs for suspend-to-idle"). I checked that the issue got
fixed if that commit was reverted.
I debugged and found that although PNP0C0D:00 (representing the LID)
is wake capable and should wakeup the system per the code in
acpi_wakeup_gpe_init() and in drivers/acpi/button.c:
localhost /sys # cat /proc/acpi/wakeup
Device S-state Status Sysfs node
LID0 S4 *enabled platform:PNP0C0D:00
CREC S5 *disabled platform:GOOG0004:00
*disabled platform:cros-ec-dev.1.auto
*disabled platform:cros-ec-accel.0
*disabled platform:cros-ec-accel.1
*disabled platform:cros-ec-gyro.0
*disabled platform:cros-ec-ring.0
*disabled platform:cros-usbpd-charger.2.auto
*disabled platform:cros-usbpd-logger.3.auto
D015 S3 *enabled i2c:i2c-ELAN0000:00
PENH S3 *enabled platform:PRP0001:00
XHCI S3 *enabled pci:0000:00:14.0
GLAN S4 *disabled
WIFI S3 *disabled pci:0000:00:14.3
localhost /sys #
On debugging, I found that its corresponding GPE is not being enabled.
The particular GPE's "gpe_register_info->enable_for_wake" does not
have any bits set when acpi_enable_all_wakeup_gpes() comes around to
use it. I looked at code and could not find any other code path that
should set the bits in "enable_for_wake" bitmask for the wake enabled
devices for s2idle. [I do see that it happens for S3 in
acpi_sleep_prepare()].
Thus I used the same call to enable the GPEs for wake enabled devices,
and verified that this fixes the regression I was seeing on multiple
of my devices.
[ rjw: The problem is that commit f941d3e41d ("ACPI: EC / PM:
Disable non-wakeup GPEs for suspend-to-idle") forgot to add
the acpi_enable_wakeup_devices() call for s2idle along with
acpi_enable_all_wakeup_gpes(). ]
Fixes: f941d3e41d ("ACPI: EC / PM: Disable non-wakeup GPEs for suspend-to-idle")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=203579
Signed-off-by: Rajat Jain <rajatja@google.com>
[ rjw: Subject & changelog ]
Cc: 5.0+ <stable@vger.kernel.org> # 5.0+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
After a previous change, all non-wakeup GPEs are disabled for
suspend-to-idle unless full Low-Power S0 (LPS0) mode is in use, so
it is not necessary to do anything in acpi_s2idle_wake() unless in
full LPS0 mode, which is only when lps0_device_handle is set.
Modify the code accordingly.
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
There are systems in which non-wakeup GPEs fire during the "noirq"
suspend stage of suspending devices and that effectively prevents the
system that tries to suspend to idle from entering any low-power
state at all. If the offending GPE fires regularly and often enough,
the system appears to be suspended, but in fact it is in a tight loop
over "noirq" suspend and "noirq" resume of devices all the time.
To prevent that from happening, disable all non-wakeup GPEs except
for the EC GPE for suspend-to-idle (the EC GPE is special, because
on some systems it has to be enabled for power button wakeup events
to be generated as expected).
Fixes: 147a7d9d25 (ACPI / PM: Do not reconfigure GPEs for suspend-to-idle)
Link: https://bugzilla.kernel.org/show_bug.cgi?id=201987
Reported-by: Zhang Rui <rui.zhang@intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Every time I tried to upgrade my laptop from 3.10.x to 4.x I faced an
issue by which the fan would run at full speed upon resume. Bisecting
it showed me the issue was introduced in 3.17 by commit 821d6f0359
(ACPI / sleep: Do not save NVS for new machines to accelerate S3). This
code only affects machines built starting as of 2012, but this Asus
1025C laptop was made in 2012 and apparently needs the NVS data to be
saved, otherwise the CPU's thermal state is not properly reported on
resume and the fan runs at full speed upon resume.
Here's a very simple way to check if such a machine is affected :
# cat /sys/class/thermal/thermal_zone0/temp
55000
( now suspend, wait one second and resume )
# cat /sys/class/thermal/thermal_zone0/temp
0
(and after ~15 seconds the fan starts to spin)
Let's apply the same quirk as commit cbc00c13 (ACPI: save NVS memory
for Lenovo G50-45) and reuse the function it provides. Note that this
commit was already backported to 4.9.x but not 4.4.x.
Cc: 3.17+ <stable@vger.kernel.org> # 3.17+: requires cbc00c13
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The Dell Venue Pro 7140 supports the Low Power S0 Idle state, but
does not support any of the _DSM functions that the current heuristic
checks for.
Since suspend-to-mem can not be safely performed on this machine,
and since the bitfield check can't cover this case, it is safer
to enable s2idle by default by checking for the presence of the
_DSM alone and removing the bitfield check.
Signed-off-by: Tristian Celestin <tristiancelestin@fastmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
On platforms where the Low Power S0 Idle _DSM interface is used,
on wakeup from suspend-to-idle, when it is known that the ACPI SCI
has triggered while suspended, dispatch the EC GPE in order to catch
all EC events that may have triggered the wakeup before carrying out
the noirq phase of device resume.
That is needed to handle power button wakeup on some platforms where
the EC goes into a low-power mode during suspend-to-idle and while in
that mode it will discard events after a timeout. If that timeout is
shorter than the time it takes to complete the noirq resume of
devices, looking for EC events after the latter is too late.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reported-by: Zhang Rui <rui.zhang@intel.com>
Tested-by: Wendy Wang <wendy.wang@intel.com>
ThinkPad X1 Tablet(2016) is reported to have issues with
the Low Power S0 Idle _DSM interface and since this machine
model generally can do ACPI S3 just fine, and user would
like to use S3 as default sleep model, add a blacklist
entry to disable that interface for ThinkPad X1 Tablet(2016).
Link: https://bugzilla.kernel.org/show_bug.cgi?id=199057
Reported-and-tested-by: Robin Lee <robinlee.sysu@gmail.com>
Signed-off-by: Chen Yu <yu.c.chen@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
- Modify the cpuidle poll state implementation to prevent CPUs from
staying in the loop in there for excessive times (Rafael Wysocki).
- Add Intel Cannon Lake chips support to the RAPL power capping
driver (Joe Konno).
- Add reference counting to the device links handling code in the
PM core (Lukas Wunner).
- Avoid reconfiguring GPEs on suspend-to-idle in the ACPI system
suspend code (Rafael Wysocki).
- Allow devices to be put into deeper low-power states via ACPI
if both _SxD and _SxW are missing (Daniel Drake).
- Reorganize the core ACPI suspend-to-idle wakeup code to avoid a
keyboard wakeup issue on Asus UX331UA (Chris Chiu).
- Prevent the PCMCIA library code from aborting suspend-to-idle due
to noirq suspend failures resulting from incorrect assumptions
(Rafael Wysocki).
- Add coupled cpuidle supprt to the Exynos3250 platform (Marek
Szyprowski).
- Add new sysfs file to make it easier to specify the image storage
location during hibernation (Mario Limonciello).
- Add sysfs files for collecting suspend-to-idle usage and time
statistics for CPU idle states (Rafael Wysocki).
- Update the pm-graph utilities (Todd Brandt).
- Reduce the kernel log noise related to reporting Low-power Idle
constraings by the ACPI system suspend code (Rafael Wysocki).
- Make it easier to distinguish dedicated wakeup IRQs in the
/proc/interrupts output (Tony Lindgren).
- Add the frequency table validation in cpufreq to the core and
drop it from a number of cpufreq drivers (Viresh Kumar).
- Drop "cooling-{min|max}-level" for CPU nodes from a couple of
DT bindings (Viresh Kumar).
- Clean up the CPU online error code path in the cpufreq core
(Viresh Kumar).
- Fix assorted issues in the SCPI, CPPC, mediatek and tegra186
cpufreq drivers (Arnd Bergmann, Chunyu Hu, George Cherian,
Viresh Kumar).
- Drop memory allocation error messages from a few places in
cpufreq and cpuildle drivers (Markus Elfring).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=6JC2
-----END PGP SIGNATURE-----
Merge tag 'pm-4.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"These update the cpuidle poll state definition to reduce excessive
energy usage related to it, add new CPU ID to the RAPL power capping
driver, update the ACPI system suspend code to handle some special
cases better, extend the PM core's device links code slightly, add new
sysfs attribute for better suspend-to-idle diagnostics and easier
hibernation handling, update power management tools and clean up
cpufreq quite a bit.
Specifics:
- Modify the cpuidle poll state implementation to prevent CPUs from
staying in the loop in there for excessive times (Rafael Wysocki).
- Add Intel Cannon Lake chips support to the RAPL power capping
driver (Joe Konno).
- Add reference counting to the device links handling code in the PM
core (Lukas Wunner).
- Avoid reconfiguring GPEs on suspend-to-idle in the ACPI system
suspend code (Rafael Wysocki).
- Allow devices to be put into deeper low-power states via ACPI if
both _SxD and _SxW are missing (Daniel Drake).
- Reorganize the core ACPI suspend-to-idle wakeup code to avoid a
keyboard wakeup issue on Asus UX331UA (Chris Chiu).
- Prevent the PCMCIA library code from aborting suspend-to-idle due
to noirq suspend failures resulting from incorrect assumptions
(Rafael Wysocki).
- Add coupled cpuidle supprt to the Exynos3250 platform (Marek
Szyprowski).
- Add new sysfs file to make it easier to specify the image storage
location during hibernation (Mario Limonciello).
- Add sysfs files for collecting suspend-to-idle usage and time
statistics for CPU idle states (Rafael Wysocki).
- Update the pm-graph utilities (Todd Brandt).
- Reduce the kernel log noise related to reporting Low-power Idle
constraings by the ACPI system suspend code (Rafael Wysocki).
- Make it easier to distinguish dedicated wakeup IRQs in the
/proc/interrupts output (Tony Lindgren).
- Add the frequency table validation in cpufreq to the core and drop
it from a number of cpufreq drivers (Viresh Kumar).
- Drop "cooling-{min|max}-level" for CPU nodes from a couple of DT
bindings (Viresh Kumar).
- Clean up the CPU online error code path in the cpufreq core (Viresh
Kumar).
- Fix assorted issues in the SCPI, CPPC, mediatek and tegra186
cpufreq drivers (Arnd Bergmann, Chunyu Hu, George Cherian, Viresh
Kumar).
- Drop memory allocation error messages from a few places in cpufreq
and cpuildle drivers (Markus Elfring)"
* tag 'pm-4.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (56 commits)
ACPI / PM: Fix keyboard wakeup from suspend-to-idle on ASUS UX331UA
cpufreq: CPPC: Use transition_delay_us depending transition_latency
PM / hibernate: Change message when writing to /sys/power/resume
PM / hibernate: Make passing hibernate offsets more friendly
cpuidle: poll_state: Avoid invoking local_clock() too often
PM: cpuidle/suspend: Add s2idle usage and time state attributes
cpuidle: Enable coupled cpuidle support on Exynos3250 platform
cpuidle: poll_state: Add time limit to poll_idle()
cpufreq: tegra186: Don't validate the frequency table twice
cpufreq: speedstep: Don't validate the frequency table twice
cpufreq: sparc: Don't validate the frequency table twice
cpufreq: sh: Don't validate the frequency table twice
cpufreq: sfi: Don't validate the frequency table twice
cpufreq: scpi: Don't validate the frequency table twice
cpufreq: sc520: Don't validate the frequency table twice
cpufreq: s3c24xx: Don't validate the frequency table twice
cpufreq: qoirq: Don't validate the frequency table twice
cpufreq: pxa: Don't validate the frequency table twice
cpufreq: ppc_cbe: Don't validate the frequency table twice
cpufreq: powernow: Don't validate the frequency table twice
...
This issue happens on new ASUS laptop UX331UA which has modern
standby mode (suspend-to-idle). Pressing keys on the PS2 keyboard
can't wake up the system from suspend-to-idle which is not expected.
However, pressing power button can wake up without problem.
Per the engineers of ASUS, the keypress event is routed to Embedded
Controller (EC) in standby mode. EC then signals the SCI event to
BIOS so BIOS would Notify() power button to wake up the system. It's
from BIOS perspective. What we observe here is that kernel receives
the SCI event from SCI interrupt handler which informs that the GPE
status bit belongs to EC needs to be handled and then queries the EC
to find out what event is pending. Then execute the following ACPI
_QDF method which defined in ACPI DSDT for EC to notify power button.
Method (_QDF, 0, NotSerialized) // _Qxx: EC Query
{
Notify (PWRB, 0x80) // Status Change
}
With more debug messages added to analyze this problem, we find that
the keypress does wake up the system from suspend-to-idle but it's back
to suspend again almost immediately. As we see in the following messages,
the acpi_button_notify() is invoked but acpi_pm_wakeup_event() can not
really wake up the system here because acpi_s2idle_wakeup() is false.
The acpi_s2idle_wakeup() returnd false because the acpi_s2idle_sync() has
alrealdy exited.
[ 52.987048] s2idle_loop going s2idle
[ 59.713392] acpi_s2idle_wake enter
[ 59.713394] acpi_s2idle_wake exit
[ 59.760888] acpi_ev_gpe_detect enter
[ 59.760893] acpi_s2idle_sync enter
[ 59.760893] acpi_ec_query_flushed ec pending queries 0
[ 59.760953] Read registers for GPE 50-57: Status=01, Enable=01, RunEnable=01, WakeEnable=00
[ 59.760955] ACPI: EC: ===== IRQ (1) =====
[ 59.760972] ACPI: EC: EC_SC(R) = 0x28 SCI_EVT=1 BURST=0 CMD=1 IBF=0 OBF=0
[ 59.760979] ACPI: EC: +++++ Polling enabled +++++
[ 59.760979] ACPI: EC: ##### Command(QR_EC) submitted/blocked #####
[ 59.761003] acpi_s2idle_sync exit
[ 59.769587] ACPI: EC: ##### Query(0xdf) started #####
[ 59.769611] ACPI: EC: ##### Query(0xdf) stopped #####
[ 59.774154] acpi_button_notify button type 1
[ 59.813175] s2idle_loop going s2idle
acpi_s2idle_sync() already makes an effort to flush the EC event
queue, but in this case, the EC event has yet to be generated when
the call to acpi_ec_flush_work() is made. The event is generated
shortly after, through the ongoing handling of the SCI interrupt
which is happening on another CPU, and we must synchronize that
to make sure that it has run and completed. Adding another call to
acpi_os_wait_events_complete() solves this issue, since that
function synchronizes with SCI interrupt completion.
Signed-off-by: Chris Chiu <chiu@endlessm.com>
[ rjw: Subject ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
If a device referred to by ACPI LPI constrains (coming from function 1
of the Low Power S0 Idle _DSM interface) is not power-manageable via
ACPI (no _PS0 method and no power resources), the code generating
diagnostic information for the LPI constraints will print a message
about that to the kernel log on every system suspend-resume cycle
(possibly for multiple times).
That is not very useful and noisy, so modify that code to disregard
the LPI list entries corresponding to the devices that are not power-
manageable after printing that information for them once.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
...instead of open coding its functionality.
No changes in functionality.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Jean Delvare <jdelvare@suse.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-acpi@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Link: http://lkml.kernel.org/r/20180222125923.57385-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
It is reported that commit 235d81a630 (ACPI / PM: Clean up device
wakeup enable/disable code) broke wakeup from suspend-to-idle on
some platforms. That is due to the acpi_enable_all_wakeup_gpes() in
acpi_s2idle_prepare() which needs acpi_enable_wakeup_devices() to be
called before it as the latter sets up the GPE masks used by the
former and commit 235d81a630 removed acpi_enable_wakeup_devices()
invocation from the suspend-to-idle path.
However, acpi_enable_wakeup_devices() does more than just setting
the GPE masks and the remaining part of it is not necessary for
suspend-to-idle. Moreover, non-wakeup GPEs are disabled on suspend-
to-idle entry to avoid spurious wakeups, but that should not be
strictly necessary any more after commit 33e4f80ee6 (ACPI / PM:
Ignore spurious SCI wakeups from suspend-to-idle) which prevents
spurious GPE wakeups from resuming the system. The only consequence
of leaving non-wakeup GPEs enabled may be more interrupt-related
activity while suspended, which is not ideal (more energy is used
if that happens), but it is not critical too.
For this reason, drop the GPE reconfiguration from the suspend-to-idle
path entirely.
This change also allows Dells XPS13 9360 blacklisted by commit
71630b7a83 (ACPI / PM: Blacklist Low Power S0 Idle _DSM for Dell
XPS13 9360) to use the power button for waking up from suspend-
to-idle and it helps at least one other older Dell system (the
wakeup button GPE on that one is not listed in _PRW for any
devices, so it is not regarded as a wakeup one and gets disabled
on suspend-to-idle entry today).
Fixes: 235d81a630 (ACPI / PM: Clean up device wakeup enable/disable code)
Reported-by: Du Wenkai <wenkai.du@intel.com>
Tested-by: Du Wenkai <wenkai.du@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Some systems don't support the ACPI_LPS0_ENTRY and ACPI_LPS0_EXIT
functions in their Low Power S0 Idle _DSM, but still expect EC
events to be processed in the suspend-to-idle state for power button
wakeup (among other things) to work. Surface Pro3 turns out to be
one of them.
Fortunately, it still provides Low Power S0 Idle _DSM with the screen
on/off functions supported, so modify the ACPI suspend-to-idle to use
the Low Power S0 Idle code path for all systems supporting the
ACPI_LPS0_ENTRY and ACPI_LPS0_EXIT or the ACPI_LPS0_SCREEN_OFF and
ACPI_LPS0_SCREEN_ON functions in their Low Power S0 Idle _DSM.
Potentially, that will cause more systems to use suspend-to-idle by
default, so some future corrections may be necessary if it leads
to issues, but let it remain more straightforward for now.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=198389#add_comment
Reported-by: Valentin Manea <valy@mrs.ro>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Valentin Manea <valy@mrs.ro>
The ACPI code supporting system transitions to sleep states uses
an internal blacklist to apply special handling to some machines
reported to behave incorrectly in some ways.
However, some entries of that blacklist cover problematic as well as
non-problematic systems, so give the users of the latter a chance to
ignore the blacklist and run their systems in the default way by
adding acpi_sleep=nobl to the kernel command line.
For example, that allows the users of Dell XPS13 9360 systems not
affected by the issue that caused the blacklist entry for this
machine to be added by commit 71630b7a83 (ACPI / PM: Blacklist Low
Power S0 Idle _DSM for Dell XPS13 9360) to use suspend-to-idle with
the Low Power S0 Idle _DSM interface which in principle should be
more energy-efficient than S3 on them.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
At least one Dell XPS13 9360 is reported to have serious issues with
the Low Power S0 Idle _DSM interface and since this machine model
generally can do ACPI S3 just fine, add a blacklist entry to disable
that interface for Dell XPS13 9360.
Fixes: 8110dd281e (ACPI / sleep: EC-based wakeup from suspend-to-idle on recent systems)
Link: https://bugzilla.kernel.org/show_bug.cgi?id=196907
Reported-by: Paul Menzel <pmenzel@molgen.mpg.de>
Tested-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: 4.13+ <stable@vger.kernel.org> # 4.13+
... and __initconst if applicable.
Based on similar work for an older kernel in the Grsecurity patch.
[JD: fix toshiba-wmi build]
[JD: add htcpen]
[JD: move __initconst where checkscript wants it]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
- Update the ACPICA code in the kernel to upstream revision 20170728
including:
* Alias operator handling update (Bob Moore).
* Deferred resolution of reference package elements (Bob Moore).
* Support for the _DMA method in walk resources (Bob Moore).
* Tables handling update and support for deferred table
verification (Lv Zheng).
* Update of SMMU models for IORT (Robin Murphy).
* Compiler and disassembler updates (Alex James, Erik Schmauss,
Ganapatrao Kulkarni, James Morse).
* Tools updates (Erik Schmauss, Lv Zheng).
* Assorted minor fixes and cleanups (Bob Moore, Kees Cook,
Lv Zheng, Shao Ming).
- Rework the initialization of non-wakeup GPEs with method handlers
in order to address a boot crash on some systems with Thunderbolt
devices connected at boot time where we miss an early hotplug
event due to a delay in GPE enabling (Rafael Wysocki).
- Rework the handling of PCI bridges when setting up ACPI-based
device wakeup in order to avoid disabling wakeup for bridges
prematurely (Rafael Wysocki).
- Consolidate Apple DMI checks throughout the tree, add support for
Apple device properties to the device properties framework and
use these properties for the handling of I2C and SPI devices on
Apple systems (Lukas Wunner).
- Add support for _DMA to the ACPI-based device properties lookup
code and make it possible to use the information from there to
configure DMA regions on ARM64 systems (Lorenzo Pieralisi).
- Fix several issues in the APEI code, add support for exporting
the BERT error region over sysfs and update APEI MAINTAINERS
entry with reviewers information (Borislav Petkov, Dongjiu Geng,
Loc Ho, Punit Agrawal, Tony Luck, Yazen Ghannam).
- Fix a potential initialization ordering issue in the ACPI EC
driver and clean it up somewhat (Lv Zheng).
- Update the ACPI SPCR driver to extend the existing XGENE 8250
workaround in it to a new platform (m400) and to work around
an Xgene UART clock issue (Graeme Gregory).
- Add a new utility function to the ACPI core to support using
ACPI OEM ID / OEM Table ID / Revision for system identification
in blacklisting or similar and switch over the existing code
already using this information to this new interface (Toshi Kani).
- Fix an xpower PMIC issue related to GPADC reads that always return
0 without extra pin manipulations (Hans de Goede).
- Add statements to print debug messages in a couple of places in
the ACPI core for easier diagnostics (Rafael Wysocki).
- Clean up the ACPI processor driver slightly (Colin Ian King,
Hanjun Guo).
- Clean up the ACPI x86 boot code somewhat (Andy Shevchenko).
- Add a quirk for Dell OptiPlex 9020M to the ACPI backlight
driver (Alex Hung).
- Assorted fixes, cleanups and updates related to ACPI (Amitoj Kaur
Chawla, Bhumika Goyal, Frank Rowand, Jean Delvare, Punit Agrawal,
Ronald Tschalär, Sumeet Pawnikar).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=6Ke9
-----END PGP SIGNATURE-----
Merge tag 'acpi-4.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI updates from Rafael Wysocki:
"These include a usual ACPICA code update (this time to upstream
revision 20170728), a fix for a boot crash on some systems with
Thunderbolt devices connected at boot time, a rework of the handling
of PCI bridges when setting up device wakeup, new support for Apple
device properties, support for DMA configurations reported via ACPI on
ARM64, APEI-related updates, ACPI EC driver updates and assorted minor
modifications in several places.
Specifics:
- Update the ACPICA code in the kernel to upstream revision 20170728
including:
* Alias operator handling update (Bob Moore).
* Deferred resolution of reference package elements (Bob Moore).
* Support for the _DMA method in walk resources (Bob Moore).
* Tables handling update and support for deferred table
verification (Lv Zheng).
* Update of SMMU models for IORT (Robin Murphy).
* Compiler and disassembler updates (Alex James, Erik Schmauss,
Ganapatrao Kulkarni, James Morse).
* Tools updates (Erik Schmauss, Lv Zheng).
* Assorted minor fixes and cleanups (Bob Moore, Kees Cook, Lv
Zheng, Shao Ming).
- Rework the initialization of non-wakeup GPEs with method handlers
in order to address a boot crash on some systems with Thunderbolt
devices connected at boot time where we miss an early hotplug event
due to a delay in GPE enabling (Rafael Wysocki).
- Rework the handling of PCI bridges when setting up ACPI-based
device wakeup in order to avoid disabling wakeup for bridges
prematurely (Rafael Wysocki).
- Consolidate Apple DMI checks throughout the tree, add support for
Apple device properties to the device properties framework and use
these properties for the handling of I2C and SPI devices on Apple
systems (Lukas Wunner).
- Add support for _DMA to the ACPI-based device properties lookup
code and make it possible to use the information from there to
configure DMA regions on ARM64 systems (Lorenzo Pieralisi).
- Fix several issues in the APEI code, add support for exporting the
BERT error region over sysfs and update APEI MAINTAINERS entry with
reviewers information (Borislav Petkov, Dongjiu Geng, Loc Ho, Punit
Agrawal, Tony Luck, Yazen Ghannam).
- Fix a potential initialization ordering issue in the ACPI EC driver
and clean it up somewhat (Lv Zheng).
- Update the ACPI SPCR driver to extend the existing XGENE 8250
workaround in it to a new platform (m400) and to work around an
Xgene UART clock issue (Graeme Gregory).
- Add a new utility function to the ACPI core to support using ACPI
OEM ID / OEM Table ID / Revision for system identification in
blacklisting or similar and switch over the existing code already
using this information to this new interface (Toshi Kani).
- Fix an xpower PMIC issue related to GPADC reads that always return
0 without extra pin manipulations (Hans de Goede).
- Add statements to print debug messages in a couple of places in the
ACPI core for easier diagnostics (Rafael Wysocki).
- Clean up the ACPI processor driver slightly (Colin Ian King, Hanjun
Guo).
- Clean up the ACPI x86 boot code somewhat (Andy Shevchenko).
- Add a quirk for Dell OptiPlex 9020M to the ACPI backlight driver
(Alex Hung).
- Assorted fixes, cleanups and updates related to ACPI (Amitoj Kaur
Chawla, Bhumika Goyal, Frank Rowand, Jean Delvare, Punit Agrawal,
Ronald Tschalär, Sumeet Pawnikar)"
* tag 'acpi-4.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (75 commits)
ACPI / APEI: Suppress message if HEST not present
intel_pstate: convert to use acpi_match_platform_list()
ACPI / blacklist: add acpi_match_platform_list()
ACPI, APEI, EINJ: Subtract any matching Register Region from Trigger resources
ACPI: make device_attribute const
ACPI / sysfs: Extend ACPI sysfs to provide access to boot error region
ACPI: APEI: fix the wrong iteration of generic error status block
ACPI / processor: make function acpi_processor_check_duplicates() static
ACPI / EC: Clean up EC GPE mask flag
ACPI: EC: Fix possible issues related to EC initialization order
ACPI / PM: Add debug statements to acpi_pm_notify_handler()
ACPI: Add debug statements to acpi_global_event_handler()
ACPI / scan: Enable GPEs before scanning the namespace
ACPICA: Make it possible to enable runtime GPEs earlier
ACPICA: Dispatch active GPEs at init time
ACPI: SPCR: work around clock issue on xgene UART
ACPI: SPCR: extend XGENE 8250 workaround to m400
ACPI / LPSS: Don't abort ACPI scan on missing mem resource
mailbox: pcc: Drop uninformative output during boot
ACPI/IORT: Add IORT named component memory address limits
...
* pm-sleep:
ACPI / PM: Check low power idle constraints for debug only
PM / s2idle: Rename platform operations structure
PM / s2idle: Rename ->enter_freeze to ->enter_s2idle
PM / s2idle: Rename freeze_state enum and related items
PM / s2idle: Rename PM_SUSPEND_FREEZE to PM_SUSPEND_TO_IDLE
ACPI / PM: Prefer suspend-to-idle over S3 on some systems
platform/x86: intel-hid: Wake up Dell Latitude 7275 from suspend-to-idle
PM / suspend: Define pr_fmt() in suspend.c
PM / suspend: Use mem_sleep_labels[] strings in messages
PM / sleep: Put pm_test under CONFIG_PM_SLEEP_DEBUG
PM / sleep: Check pm_wakeup_pending() in __device_suspend_noirq()
PM / core: Add error argument to dpm_show_time()
PM / core: Split dpm_suspend_noirq() and dpm_resume_noirq()
PM / s2idle: Rearrange the main suspend-to-idle loop
PM / timekeeping: Print debug messages when requested
PM / sleep: Mark suspend/hibernation start and finish
PM / sleep: Do not print debug messages by default
PM / suspend: Export pm_suspend_target_state
For SoC to achieve its lowest power platform idle state a set of hardware
preconditions must be met. These preconditions or constraints can be
obtained by issuing a device specific method (_DSM) with function "1".
Refer to the document provided in the link below.
Here during initialization (from attach() callback of LPS0 device), invoke
function 1 to get the device constraints. Each enabled constraint is
stored in a table.
The devices in this table are used to check whether they were in required
minimum state, while entering suspend. This check is done from platform
freeze wake() callback, only when /sys/power/pm_debug_messages attribute
is non zero.
If any constraint is not met and device is ACPI power managed then it
prints the device information to kernel logs.
Also if debug is enabled in acpi/sleep.c, the constraint table and state
of each device on wake is dumped in kernel logs.
Since pm_debug_messages_on setting is used as condition to check
constraints outside kernel/power/main.c, pm_debug_messages_on is changed
to a global variable.
Link: http://www.uefi.org/sites/default/files/resources/Intel_ACPI_Low_Power_S0_Idle.pdf
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Rename struct platform_freeze_ops to platform_s2idle_ops to make it
clear that the callbacks in it are used during suspend-to-idle
suspend/resume transitions and rename the related functions,
variables and so on accordingly.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
To make it clear that the symbol in question refers to
suspend-to-idle, rename it from PM_SUSPEND_FREEZE to
PM_SUSPEND_TO_IDLE.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Modify the ACPI system sleep support setup code to select
suspend-to-idle as the default system sleep state if
(1) the ACPI_FADT_LOW_POWER_S0 flag is set in the FADT and
(2) the Low Power Idle S0 _DSM interface has been discovered and
(3) the default sleep state was not selected from the kernel command
line.
The main motivation for this change is that systems where the (1) and
(2) conditions are met typically ship with OSes that don't exercise
the S3 path in the platform firmware which remains untested and turns
out to be non-functional at least in some cases.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Mario Limonciello <mario.limonciello@dell.com>
Function acpi_sleep_syscore_init has no external user so it should be
static.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit eed4d47efe (ACPI / sleep: Ignore spurious SCI wakeups from
suspend-to-idle) introduced acpi_freeze_sync() whose purpose is to
flush all of the processing of possible wakeup events signaled via
the ACPI SCI. However, it doesn't flush the query workqueue used
by the EC driver, so the events generated by the EC may not be
processed timely which leads to issues (increased overhead at least,
lost events possibly).
To fix that introduce acpi_ec_flush_work() that will flush all of
the outstanding EC work and call it from acpi_freeze_sync().
Fixes: eed4d47efe (ACPI / sleep: Ignore spurious SCI wakeups from suspend-to-idle)
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Some recent Dell laptops, including the XPS13 model numbers 9360 and
9365, cannot be woken up from suspend-to-idle by pressing the power
button which is unexpected and makes that feature less usable on
those systems. Moreover, on the 9365 ACPI S3 (suspend-to-RAM) is
not expected to be used at all (the OS these systems ship with never
exercises the ACPI S3 path in the firmware) and suspend-to-idle is
the only viable system suspend mechanism there.
The reason why the power button wakeup from suspend-to-idle doesn't
work on those systems is because their power button events are
signaled by the EC (Embedded Controller), whose GPE (General Purpose
Event) line is disabled during suspend-to-idle transitions in Linux.
That is done on purpose, because in general the EC tends to be noisy
for various reasons (battery and thermal updates and similar, for
example) and all events signaled by it would kick the CPUs out of
deep idle states while in suspend-to-idle, which effectively might
defeat its purpose.
Of course, on the Dell systems in question the EC GPE must be enabled
during suspend-to-idle transitions for the button press events to
be signaled while suspended at all, but fortunately there is a way
out of this puzzle.
First of all, those systems have the ACPI_FADT_LOW_POWER_S0 flag set
in their ACPI tables, which means that the OS is expected to prefer
the "low power S0 idle" system state over ACPI S3 on them. That
causes the most recent versions of other OSes to simply ignore ACPI
S3 on those systems, so it is reasonable to expect that it should not
be necessary to block GPEs during suspend-to-idle on them.
Second, in addition to that, the systems in question provide a special
firmware interface that can be used to indicate to the platform that
the OS is transitioning into a system-wide low-power state in which
certain types of activity are not desirable or that it is leaving
such a state and that (in principle) should allow the platform to
adjust its operation mode accordingly.
That interface is a special _DSM object under a System Power
Management Controller device (PNP0D80). The expected way to use it
is to invoke function 0 from it on system initialization, functions
3 and 5 during suspend transitions and functions 4 and 6 during
resume transitions (to reverse the actions carried out by the
former). In particular, function 5 from the "Low-Power S0" device
_DSM is expected to cause the platform to put itself into a low-power
operation mode which should include making the EC less verbose (so to
speak). Next, on resume, function 6 switches the platform back to
the "working-state" operation mode.
In accordance with the above, modify the ACPI suspend-to-idle code
to look for the "Low-Power S0" _DSM interface on platforms with the
ACPI_FADT_LOW_POWER_S0 flag set in the ACPI tables. If it's there,
use it during suspend-to-idle transitions as prescribed and avoid
changing the GPE configuration in that case. [That should reflect
what the most recent versions of other OSes do.]
Also modify the ACPI EC driver to make it handle events during
suspend-to-idle in the usual way if the "Low-Power S0" _DSM interface
is going to be used to make the power button events work while
suspended on the Dell machines mentioned above
Link: http://www.uefi.org/sites/default/files/resources/Intel_ACPI_Low_Power_S0_Idle.pdf
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The ACPI SCI (System Control Interrupt) is set up as a wakeup IRQ
during suspend-to-idle transitions and, consequently, any events
signaled through it wake up the system from that state. However,
on some systems some of the events signaled via the ACPI SCI while
suspended to idle should not cause the system to wake up. In fact,
quite often they should just be discarded.
Arguably, systems should not resume entirely on such events, but in
order to decide which events really should cause the system to resume
and which are spurious, it is necessary to resume up to the point
when ACPI SCIs are actually handled and processed, which is after
executing dpm_resume_noirq() in the system resume path.
For this reasons, add a loop around freeze_enter() in which the
platforms can process events signaled via multiplexed IRQ lines
like the ACPI SCI and add suspend-to-idle hooks that can be
used for this purpose to struct platform_freeze_ops.
In the ACPI case, the ->wake hook is used for checking if the SCI
has triggered while suspended and deferring the interrupt-induced
system wakeup until the events signaled through it are actually
processed sufficiently to decide whether or not the system should
resume. In turn, the ->sync hook allows all of the relevant event
queues to be flushed so as to prevent events from being missed due
to race conditions.
In addition to that, some ACPI code processing wakeup events needs
to be modified to use the "hard" version of wakeup triggers, so that
it will cause a system resume to happen on device-induced wakeup
events even if the "soft" mechanism to prevent the system from
suspending is not enabled. However, to preserve the existing
behavior with respect to suspend-to-RAM, this only is done in
the suspend-to-idle case and only if an SCI has occurred while
suspended.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The wakeup.flags.enabled flag in struct acpi_device is not used
consistently, as there is no reason why it should only apply
to the enabling/disabling of the wakeup GPE, so put the invocation
of acpi_enable_wakeup_device_power() under it too.
Moreover, it is not necessary to call
acpi_enable_wakeup_devices() and acpi_disable_wakeup_devices() for
suspend-to-idle, so don't do that.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Revert commit eed4d47efe (ACPI / sleep: Ignore spurious SCI wakeups
from suspend-to-idle) as it turned out to be premature and triggered
a number of different issues on various systems.
That includes, but is not limited to, premature suspend-to-RAM aborts
on Dell XPS 13 (9343) reported by Dominik.
The issue the commit in question attempted to address is real and
will need to be taken care of going forward, but evidently more work
is needed for this purpose.
Reported-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
- Update the ACPICA code in the kernel to upstream revision
20170303 which includes:
* Minor fixes and improvements in the core code (Bob Moore,
Seunghun Han).
* Debugger fixes (Colin Ian King, Lv Zheng).
* Compiler/disassembler improvements (Bob Moore, David Box,
Lv Zheng).
* Build-related update (Lv Zheng).
- Add new device IDs and platform-related information to the
ACPI drivers for Intel (LPSS) and AMD (APD) SoCs (Hanjun Guo,
Hans de Goede).
- Make it possible to quirk ACPI-enumerated devices as "always
present" on platforms where they are incorrectly reported as not
present by the AML and add the INT0002 device ID to the list of
"always present" devices (Hans de Goede).
- Fix the register information in the xpower PMIC driver and add
comments to map the registers to symbols used by AML to it
(Hans de Goede).
- Move the code turning off unused ACPI power resources during
system resume to a point after all devices have been resumed
to avoid issues with power resources that do not behave as
expected (Hans de Goede).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=Ytsi
-----END PGP SIGNATURE-----
Merge tag 'acpi-extra-4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more ACPI updates from Rafael Wysocki:
"These update the ACPICA code in the kernel to upstream revision
20170303 which adds a few minor fixes and improvements, update ACPI
SoC drivers with new device IDs, platform-related information and
similar, fix the register information in the xpower PMIC driver,
introduce a concept of "always present" devices to the ACPI device
enumeration code and use it to fix a problem with one platform, and
fix a system resume issue related to power resources.
Specifics:
- Update the ACPICA code in the kernel to upstream revision 20170303
which includes:
* Minor fixes and improvements in the core code (Bob Moore,
Seunghun Han).
* Debugger fixes (Colin Ian King, Lv Zheng).
* Compiler/disassembler improvements (Bob Moore, David Box, Lv
Zheng).
* Build-related update (Lv Zheng).
- Add new device IDs and platform-related information to the ACPI
drivers for Intel (LPSS) and AMD (APD) SoCs (Hanjun Guo, Hans de
Goede).
- Make it possible to quirk ACPI-enumerated devices as "always
present" on platforms where they are incorrectly reported as not
present by the AML and add the INT0002 device ID to the list of
"always present" devices (Hans de Goede).
- Fix the register information in the xpower PMIC driver and add
comments to map the registers to symbols used by AML to it (Hans de
Goede).
- Move the code turning off unused ACPI power resources during system
resume to a point after all devices have been resumed to avoid
issues with power resources that do not behave as expected (Hans de
Goede)"
* tag 'acpi-extra-4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (22 commits)
ACPI / power: Delay turning off unused power resources after suspend
ACPI / PMIC: xpower: Fix power_table addresses
ACPI / LPSS: Call pwm_add_table() for Bay Trail PWM device
ACPICA: Update version to 20170303
ACPICA: iasl: add ASL conversion tool
ACPICA: Local cache support: Allow small cache objects
ACPICA: Disassembler: Do not unconditionally remove temporary names
ACPICA: iasl: Fix IORT SMMU GSI disassembling
ACPICA: Cleanup AML opcode definitions, no functional change
ACPICA: Debugger: Add interpreter blocking mark for single-step mode
ACPICA: debugger: fix memory leak on Pathname
ACPICA: Update for automatic repair code for objects returned by evaluate_object
ACPICA: Namespace: fix operand cache leak
ACPICA: Fix several incorrect invocations of ACPICA return macro
ACPICA: Fix a module for excessive debug output
ACPICA: Update some function headers, no funtional change
ACPICA: Disassembler: Enhance resource descriptor detection
i2c: designware: Add ACPI HID for Hisilicon Hip07/08 I2C controller
ACPI / APD: Add clock frequency for Hisilicon Hip07/08 I2C controller
ACPI / bus: Add INT0002 to list of always-present devices
...
The ACPI SCI (System Control Interrupt) is set up as a wakeup IRQ
during suspend-to-idle transitions and, consequently, any events
signaled through it wake up the system from that state. However,
on some systems some of the events signaled via the ACPI SCI while
suspended to idle should not cause the system to wake up. In fact,
quite often they should just be discarded.
Arguably, systems should not resume entirely on such events, but in
order to decide which events really should cause the system to resume
and which are spurious, it is necessary to resume up to the point
when ACPI SCIs are actually handled and processed, which is after
executing dpm_resume_noirq() in the system resume path.
For this reasons, add a loop around freeze_enter() in which the
platforms can process events signaled via multiplexed IRQ lines
like the ACPI SCI and add suspend-to-idle hooks that can be
used for this purpose to struct platform_freeze_ops.
In the ACPI case, the ->wake hook is used for checking if the SCI
has triggered while suspended and deferring the interrupt-induced
system wakeup until the events signaled through it are actually
processed sufficiently to decide whether or not the system should
resume. In turn, the ->sync hook allows all of the relevant event
queues to be flushed so as to prevent events from being missed due
to race conditions.
In addition to that, some ACPI code processing wakeup events needs
to be modified to use the "hard" version of wakeup triggers, so that
it will cause a system resume to happen on device-induced wakeup
events even if the "soft" mechanism to prevent the system from
suspending is not enabled (that also helps to catch device-induced
wakeup events occurring during suspend transitions in progress).
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit 660b1113e0 (ACPI / PM: Fix consistency check for power resources
during resume) introduced a check for ACPI power resources which have
been turned on by the BIOS during suspend and turns these back off again.
This is causing problems on a Dell Venue Pro 11 7130 (i5-4300Y) it causes
the following messages to show up in dmesg:
[ 131.014605] ACPI: Waking up from system sleep state S3
[ 131.150271] acpi LNXPOWER:07: Turning OFF
[ 131.150323] acpi LNXPOWER:06: Turning OFF
[ 131.150911] acpi LNXPOWER:00: Turning OFF
[ 131.169014] ACPI : EC: interrupt unblocked
[ 131.181811] xhci_hcd 0000:00:14.0: System wakeup disabled by ACPI
[ 133.535728] pci_raw_set_power_state: 76 callbacks suppressed
[ 133.535735] iwlwifi 0000:01:00.0: Refused to change power state,
currently in D3
[ 133.597672] PM: noirq resume of devices complete after 2428.891 msecs
Followed by a bunch of iwlwifi errors later on and the pcie device
dropping from the bus (acpiphp thinks it has been unplugged).
Disabling the turning off of unused power resources fixes this. Instead
of adding a quirk for this system, this commit fixes this by moving the
disabling of unused power resources to later in the resume sequence
when the iwlwifi card has been moved out of D3 so the ref_count for
its power resource no longer is 0.
This new behavior seems to match the intend of the original commit which
commit-msg says: "(... which means that no devices are going to need them
any time soon) and we should turn them off".
This also avoids power resources which we need when bringing devices out
of D3 from getting bounced off and then back on again.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In commit 821d6f0359 (ACPI / sleep: Do not save NVS for new machines to
accelerate S3), to optimize S3 suspend/resume speed, code is introduced
to ignore NVS memory saving during S3 for all the platforms later than
2012.
But, Lenovo G50-45, a platform released in 2015, still needs NVS memory
saving during S3. A quirk is introduced for this platform.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=189431
Tested-by: Przemek <soprwa@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
[ rjw: Drop unnecessary code ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Revert commit 08b98d3291 (PM / sleep / ACPI: Use the ACPI_FADT_LOW_POWER_S0
flag) as it caused system suspend (in the default configuration) to fail
on Dell XPS13 (9360) with the Kaby Lake processor.
Fixes: 08b98d3291 (PM / sleep / ACPI: Use the ACPI_FADT_LOW_POWER_S0 flag)
Reported-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Modify the ACPI system sleep support setup code to select
suspend-to-idle as the default system sleep state if the
ACPI_FADT_LOW_POWER_S0 flag is set in the FADT and the
default sleep state was not selected from the kernel command
line.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Mario Limonciello <mario.limonciello@dell.com>
Revert commit 2c85025c75 (ACPI: Execute _PTS before system reboot)
as it is reported to cause poweroff and reboot to hang on Dell
Latitude E7250.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=187061
Reported-by: Gianpaolo <gianpaoloc@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* acpi-wdat:
watchdog: wdat_wdt: Fix warning for using 0 as NULL
watchdog: wdat_wdt: fix return value check in wdat_wdt_probe()
platform/x86: intel_pmc_ipc: Do not create iTCO watchdog when WDAT table exists
i2c: i801: Do not create iTCO watchdog when WDAT table exists
mfd: lpc_ich: Do not create iTCO watchdog when WDAT table exists
ACPI / watchdog: Add support for WDAT hardware watchdog
* acpi-ec:
ACPI / EC: Fix issues related to boot_ec
ACPI / EC: Fix a gap that ECDT EC cannot handle EC events
ACPI / EC: Fix a memory leakage issue in acpi_ec_add()
ACPI / EC: Cleanup first_ec/boot_ec code
ACPI / EC: Enable event freeze mode to improve event handling for suspend process
ACPI / EC: Add PM operations to improve event handling for suspend process
ACPI / EC: Add PM operations to improve event handling for resume process
ACPI / EC: Fix an issue that SCI_EVT cannot be detected after event is enabled
ACPI / EC: Add EC_FLAGS_QUERY_ENABLED to reveal a hidden logic
ACPI / EC: Add PM operations for suspend/resume noirq stage
This patch makes 2 changes:
1. Restore old behavior
Originally, EC driver stops handling both events and transactions in
acpi_ec_block_transactions(), and restarts to handle transactions in
acpi_ec_unblock_transactions_early(), restarts to handle both events and
transactions in acpi_ec_unblock_transactions().
While currently, EC driver still stops handling both events and
transactions in acpi_ec_block_transactions(), but restarts to handle both
events and transactions in acpi_ec_unblock_transactions_early().
This patch tries to restore the old behavior by dropping
__acpi_ec_enable_event() from acpi_unblock_transactions_early().
2. Improve old behavior
However this still cannot fix the real issue as both of the
acpi_ec_unblock_xxx() functions are invoked in the noirq stage. Since the
EC driver actually doesn't implement the event handling in the polling
mode, re-enabling the event handling too early in the noirq stage could
result in the problem that if there is no triggering source causing
advance_transaction() to be invoked, pending SCI_EVT cannot be detected by
the EC driver and _Qxx cannot be triggered.
It actually makes sense to restart the event handling in any point during
resuming after the noirq stage. Just like the boot stage where the event
handling is enabled in .add(), this patch further moves
acpi_ec_enable_event() to .resume(). After doing that, the following 2
functions can be combined:
acpi_ec_unblock_transactions_early()/acpi_ec_unblock_transactions().
The differences of the event handling availability between the old behavior
(this patch isn't applied) and the new behavior (this patch is applied) are
as follows:
!Applied Applied
before suspend Y Y
suspend before EC Y Y
suspend after EC Y Y
suspend_late Y Y
suspend_noirq Y (actually N) Y (actually N)
resume_noirq Y (actually N) Y (actually N)
resume_late Y (actually N) Y (actually N)
resume before EC Y (actually N) Y (actually N)
resume after EC Y (actually N) Y
after resume Y (actually N) Y
Where "actually N" means if there is no triggering source, the EC driver
is actually not able to notice the pending SCI_EVT occurred in the noirq
stage. So we can clearly see that this patch has improved the situation.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Tested-by: Todd E Brandt <todd.e.brandt@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Now GPE can be masked via the new acpi_mask_gpe() API and this patch
modifies /sys/firmware/acpi/interrupts/gpexx to use this new facility.
Writes "mask/unmask" to this file now invokes acpi_mask_gpe().
Reads from this file now returns new "EN/STS" when the corresponding GPE
hardware register's EN/STS bits are flagged, and new "masked/unmasked"
attribute to indicate the status of the masking mechanism.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
[ rjw: Subject ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The _PTS control method is defined in the section 7.4.1 of acpi 6.0
spec. The _PTS control method is executed by the OS during the sleep
transition process for S1, S2, S3, S4, and for orderly S5 shutdown.
The _PTS control method provides the BIOS a mechanism for performing
some housekeeping, such as writing the sleep type value to the embedded
controller, before entering the system sleeping state. Note that some
Lenovo Server BIOS use this mechanism to detect reboot event and
prompt user by popped dialog box.
According to section 7.5 of acpi 6.0 spec, _PTS should run after _TTS.
Add a _PTS evaulation to the existing _TTS reboot notifier and change
the notifier name to reflect the fact that it's not for _TTS only any
more.
Signed-off-by: Ocean He <hehy1@lenovo.com>
Signed-off-by: Nagananda Chumbalkar <nchumbalkar@lenovo.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The problem is Linux registers pm_power_off = efi_power_off only if
we are in hardware reduced mode. Actually, what we also want is to do
this when ACPI S5 is simply not supported on non-legacy platforms.
Since some future Intel platforms are HW-full mode where the DSDT
fails to supply an _S5 object(without SLP_TYP), we should let such
kind of platform to leverage efi runtime service to poweroff.
This patch uses efi power off as first choice when S5 is unavailable,
even if there is a customized poweroff(driver provided, eg).
Meanwhile, the legacy platforms will not be affected because there is
no path for them to overwrite the pm_power_off to efi power off.
Suggested-by: Len Brown <len.brown@intel.com>
Reviewed-by: Matt Fleming <matt@codeblueprint.co.uk>
Signed-off-by: Chen Yu <yu.c.chen@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit 58a1fbbb2e ("PM / PCI / ACPI: Kick devices that might have been
reset by firmware") added a runtime resume for devices that were runtime
suspended when the system entered suspend-to-RAM.
Briefly, the motivation was to ensure that devices did not remain in a
reset-power-on state after resume, potentially preventing deep SoC-wide
low-power states from being entered on idle.
Currently we're not doing the same when leaving suspend-to-disk and this
asymmetry is a problem if drivers rely on the automatic resume triggered
by pm_complete_with_resume_check(). Fix it.
Fixes: 58a1fbbb2e (PM / PCI / ACPI: Kick devices that might have been reset by firmware)
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: 4.4+ <stable@vger.kernel.org> # 4.4+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
acpi_processor_sleep is neither related nor used by CPUIdle framework.
It's used in system suspend/resume path as a syscore operation. It makes
more sense to move it to acpi/sleep.c where all the S-state transition
(a.k.a. Linux system suspend/hiberate) related code are present.
Also make it depend on CONFIG_ACPI_SYSTEM_POWER_STATES_SUPPORT so that
it's not compiled on architecture like ARM64 where S-states are not
yet defined in ACPI.
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit f06147f9fb (ACPICA: Hardware: Enable firmware waking vector
for both 32-bit and 64-bit FACS) added three functions that aren't
present in upstream ACPICA, acpi_hw_set_firmware_waking_vectors(),
acpi_set_firmware_waking_vectors() and acpi_set_firmware_waking_vector64(),
to allow Linux to use the previously existing API for setting the
platform firmware waking vector.
However, that wasn't necessary, since the ACPI sleep support code
in Linux can be modified to use the upstream ACPICA's API easily
and the additional functions may be dropped which reduces the code
size and puts the kernel's ACPICA code more in line with the upstream.
Make the changes as per the above. While at it, make the relevant
function desctiption comments reflect the upstream ACPICA's ones.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Lv Zheng <lv.zheng@intel.com>
* pm-sleep:
PM / hibernate: fix a comment typo
input: i8042: Avoid resetting controller on system suspend/resume
PM / PCI / ACPI: Kick devices that might have been reset by firmware
PM / sleep: Add flags to indicate platform firmware involvement
PM / sleep: Drop pm_request_idle() from pm_generic_complete()
PCI / PM: Avoid resuming more devices during system suspend
PM / wakeup: wakeup_source_create: use kstrdup_const
PM / sleep: Report interrupt that caused system wakeup
For an ACPI compatible system, the SCI (ACPI System Control
Interrupt) is used to wake the system up from suspend-to-idle.
Once the CPU is woken up by the SCI, the interrupt handler will
first check if the current IRQ has been configured for system
wakeup, so irq_pm_check_wakeup() is invoked to validate the IRQ
number. However, during suspend-to-idle, enable_irq_wake() is
called for acpi_gbl_FADT.sci_interrupt, although the IRQ number
that the SCI handler has been installed for should be passed to
it instead. Thus, if acpi_gbl_FADT.sci_interrupt happens to be
different from that number, ACPI interrupts will not be able to
wake up the system from sleep.
Fix this problem by passing the IRQ number returned by
acpi_gsi_to_irq() to enable_irq_wake() instead of
acpi_gbl_FADT.sci_interrupt.
Cc: 3.18+ <stable@vger.kernel.org> # 3.18+
Acked-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Chen Yu <yu.c.chen@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
There are quite a few cases in which device drivers, bus types or
even the PM core itself may benefit from knowing whether or not
the platform firmware will be involved in the upcoming system power
transition (during system suspend) or whether or not it was involved
in it (during system resume).
For this reason, introduce global system suspend flags that can be
used by the platform code to expose that information for the benefit
of the other parts of the kernel and make the ACPI core set them
as appropriate.
Users of the new flags will be added later.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Currently, in suspend-to-idle, wakeup GPE for PCI devices are
handled properly because acpi_pci_sleep_wake() invokes acpi_enable_gpe()
to enable the wakeup GPE directly. But for the other wakeup-capable
devices in ACPI bus, acpi_enable_wakeup_devices() should be invoked
to update enable_for_wake mask in gpe_register_info structure, thus
acpi_enable_all_wakeup_gpes() can enable the wakeup GPE referred in
_PRW methods. And acpi_disable_wakeup_devices() will be called
before disable_irq_wake() in acpi_freeze_restore() to restore the mask.
This patch fixes a power button wakeup problem on Surface Pro 3,
on which platform power button uses EC to deliver event
(EC GPE is referred in _PRW).
Note: enabling EC GPE during freeze state may bring some risks
because EC events are expected to fire more frequently than others.
Thus it may bring the system out of freeze state unnecessarily.
(We already have comments about this in bugzilla)
Link: https://bugzilla.kernel.org/show_bug.cgi?id=84651
Reported-and-tested-by: Ethan Schoonover <es@ethanschoonover.com>
Tested-by: Peter Amidon <psa.pub.0@picnicpark.org>
Tested-by: Yani Ioadnnou <yani.ioannou@gmail.com>
Tested-by: Mister Wardrop <mister.wardrop@gmail.com>
Tested-by: Anton Anikin <anton@anikin.name>
Tested-by: Keith McClelland <zismylaptop@gmail.com>
Reviewed-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Chen Yu <yu.c.chen@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The acpi_suspend() function has no callers, so drop it.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Hanjun Guo <hanjun.guo@linaro.org>
This makes a difference if the compiler decides not to inline the
function, as then the function's reference to acpisleep_dmi_table[]
yields a section mismatch warning.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
After multiple GPEs have been disabled at the low level in one go,
like when acpi_disable_all_gpes() is called, we should always drain
all of the outstanding events from them, or interesting races become
possible.
For this reason, call acpi_os_wait_events_complete() after
acpi_enable_all_wakeup_gpes() and acpi_disable_all_gpes() in
acpi_freeze_prepare() and acpi_power_off_prepare(), respectively.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The ACPI GPE wakeup from suspend-to-idle is currently based on using
the IRQF_NO_SUSPEND flag for the ACPI SCI, but that is problematic
for a couple of reasons. First, in principle the ACPI SCI may be
shared and IRQF_NO_SUSPEND does not really work well with shared
interrupts. Second, it may require the ACPI subsystem to special-case
the handling of device notifications depending on whether or not
they are received during suspend-to-idle in some places which would
lead to fragile code. Finally, it's better the handle ACPI wakeup
interrupts consistently with wakeup interrupts from other sources.
For this reason, remove the IRQF_NO_SUSPEND flag from the ACPI SCI
and use enable_irq_wake()/disable_irq_wake() with it instead, which
requires two additional platform hooks to be added to struct
platform_freeze_ops.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
NVS region is saved and restored unconditionally for machines without
nvs_nosave quirk during S3. Tested some new machines and the operation
is not necessary. Saving NVS region also affects S2RAM speed. The time of
NVS saving and restoring depends on the size of NVS region and it consumes
7~10ms normally.
This patch is to make machines produced from 2012 to now not saving NVS region
to accelerate S3.
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Adds trace events that give finer resolution into suspend/resume. These
events are graphed in the timelines generated by the analyze_suspend.py
script. They represent large areas of time consumed that are typical to
suspend and resume.
The event is triggered by calling the function "trace_suspend_resume"
with three arguments: a string (the name of the event to be displayed
in the timeline), an integer (case specific number, such as the power
state or cpu number), and a boolean (where true is used to denote the start
of the timeline event, and false to denote the end).
The suspend_resume trace event reproduces the data that the machine_suspend
trace event did, so the latter has been removed.
Signed-off-by: Todd Brandt <todd.e.brandt@intel.com>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The "freeze" sleep state suffers from the same issue that was
addressed by commit ad07277e82 (ACPI / PM: Hold acpi_scan_lock over
system PM transitions) for ACPI sleep states, that is, things break
if ->remove() is called for devices whose system resume callbacks
haven't been executed yet.
It also can be addressed in the same way, by holding the ACPI scan
lock over the "freeze" sleep state and PM transitions to and from
that state, but ->begin() and ->end() platform operations for the
"freeze" sleep state are needed for this purpose.
This change has been tested on Acer Aspire S5 with Thunderbolt.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Export the acpi_target_system_state() function to modules so that
modular drivers can use it to check what the target ACPI sleep state
of the system is (that is needed for i915 mostly at this point).
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
If the HW Reduced ACPI mode bit is set in the FADT, ACPICA uses
the optional sleep control and sleep status registers for making
the system enter sleep states (including S5), so it is not possible
to use system sleep states or power it off using ACPI if the HW
Reduced ACPI mode bit is set and those registers are not available.
For this reason, add a new function, acpi_sleep_state_supported(),
checking if the HW Reduced ACPI mode bit is set and whether or not
system sleep states are usable in that case in addition to checking
the return value of acpi_get_sleep_type_data() and make the ACPI
sleep setup routines use that function to check the availability of
system sleep states.
Among other things, this prevents the kernel from attempting to
use ACPI for powering off HW Reduced ACPI systems without the sleep
control and sleep status registers, because ACPI power off doesn't
have a chance to work on them. That allows alternative power off
mechanisms that may actually work to be used on those systems. The
affected machines include Dell Venue 8 Pro, Asus T100TA, Haswell
Desktop SDP and Ivy Bridge EP Demo depot.
References: https://bugzilla.kernel.org/show_bug.cgi?id=70931
Reported-by: Adam Williamson <awilliam@redhat.com>
Tested-by: Aubrey Li <aubrey.li@linux.intel.com>
Cc: 3.4+ <stable@vger.kernel.org> # 3.4+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Revert commit 3130497f5b ("ACPI / sleep: pm_power_off needs more
sanity checks to be installed") that breaks power ACPI power off on a
lot of systems, because it checks wrong registers.
Fixes: 3130497f5b ("ACPI / sleep: pm_power_off needs more sanity checks to be installed")
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Sleep control and status registers need santity checks as well before
ACPI installs acpi_power_off to pm_power_off hook. The checking code in
acpi_enter_sleep_state() is too late, we should not allow a not-working
pm_power_off function to be hooked up.
Signed-off-by: Aubrey Li <aubrey.li@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* acpi-gpe:
ACPI / EC: disable GPE before removing GPE handler
ACPI / Button: Fix enabling button GPEs twice
* acpi-video:
ACPI: Blacklist Win8 OSI for some HP laptop 2013 models
ACPI / video: Fix typo in video_detect.c
* acpi-thermal:
ACPI / thermal: remove const from thermal_zone_device_ops declaration
* acpi-processor:
ACPI / scan: bail out early if failed to parse APIC ID for CPU
* acpi-sleep:
ACPI / sleep: remove panic in case hardware has changed after S4
* acpi-cleanup: (22 commits)
ACPI / tables: Return proper error codes from acpi_table_parse() and fix comment.
ACPI / tables: Check if id is NULL in acpi_table_parse()
ACPI / proc: Include appropriate header file in proc.c
ACPI / EC: Remove unused functions and add prototype declaration in internal.h
ACPI / dock: Include appropriate header file in dock.c
ACPI / PCI: Include appropriate header file in pci_link.c
ACPI / PCI: Include appropriate header file in pci_slot.c
ACPI / EC: Mark the function acpi_ec_add_debugfs() as static in ec_sys.c
ACPI / NVS: Include appropriate header file in nvs.c
ACPI / OSL: Mark the function acpi_table_checksum() as static
ACPI / processor: initialize a variable to silence compiler warning
ACPI / processor: use ACPI_COMPANION() to get ACPI device
ACPI: correct minor typos
ACPI / sleep: Drop redundant acpi_disabled check
ACPI / dock: Drop redundant acpi_disabled check
ACPI / table: Replace '1' with specific error return values
ACPI: remove trailing whitespace
ACPI / IBFT: Fix incorrect <acpi/acpi.h> inclusion in iSCSI boot firmware module
ACPI / i915: Fix incorrect <acpi/acpi.h> inclusions via <linux/acpi_io.h>
SFI / ACPI: Fix warnings reported during builds with W=1
...
Conflicts:
drivers/acpi/nvs.c
drivers/hwmon/asus_atk0110.c
Some BIOSes change hardware based on the state of
a laptop's lid. If the lid is closed, the touchpad is
disabled and the checksum changes. Windows 8 no longer
aborts resume if the checksum has changed.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
[rjw: Use pr_crit() for the message and don't break the string]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
acpi_sleep_init() is only called from acpi_bus_init() and the
code logic shows that it doesn't need to check acpi_disabled:
acpi_init();
if (acpi_disabled) return;
acpi_bus_init();
acpi_sleep_init();
if (acpi_disabled)
return 0;
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
[rjw: Subject and changelog]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Replace direct inclusions of <acpi/acpi.h>, <acpi/acpi_bus.h> and
<acpi/acpi_drivers.h>, which are incorrect, with <linux/acpi.h>
inclusions and remove some inclusions of those files that aren't
necessary.
First of all, <acpi/acpi.h>, <acpi/acpi_bus.h> and <acpi/acpi_drivers.h>
should not be included directly from any files that are built for
CONFIG_ACPI unset, because that generally leads to build warnings about
undefined symbols in !CONFIG_ACPI builds. For CONFIG_ACPI set,
<linux/acpi.h> includes those files and for CONFIG_ACPI unset it
provides stub ACPI symbols to be used in that case.
Second, there are ordering dependencies between those files that always
have to be met. Namely, it is required that <acpi/acpi_bus.h> be included
prior to <acpi/acpi_drivers.h> so that the acpi_pci_root declarations the
latter depends on are always there. And <acpi/acpi.h> which provides
basic ACPICA type declarations should always be included prior to any other
ACPI headers in CONFIG_ACPI builds. That also is taken care of including
<linux/acpi.h> as appropriate.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com> (drivers/pci stuff)
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> (Xen stuff)
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Initialize pwr_btn_status as disabled which (a) makes sure it is
in a proper state to start, and (b) cleans up a compiler warning
about an uninitialized variable.
Signed-off-by: Al Stone <al.stone@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Bad things happen if ACPI hotplug events are handled during system
PM transitions, especially if devices are removed as a result.
To prevent those bad things from happening, acquire acpi_scan_lock
when a PM transition is started and release it when that transition
is complete or has been aborted.
This fixes resume lockup on my test-bed Acer Aspire S5 that happens
when Thunderbolt devices are disconnected from the machine while
suspended.
Also fixes the analogous problem for Mika Westerberg on an
Intel DZ77RE-75K board.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Toshi Kani <toshi.kani@hp.com>
__initdata should be placed between the variable name and equal
sign for the variable to be placed in the intended section.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Introduce helper function acpi_execute_simple_method() and use it in
a number of places to simplify code.
[rjw: Changelog]
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Which by default will be x86_acpi_suspend_lowlevel.
This registration allows us to register another callback
if there is a need to use another platform specific callback.
Signed-off-by: Liang Tang <liang.tang@oracle.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Tested-by: Ben Guthro <benjamin.guthro@citrix.com>
Acked-by: "H. Peter Anvin" <hpa@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add Sony Vaio VGN-FW21M to the device blacklist in
drivers/acpi/sleep.c.
Fixes suspend/resume on this device (device no longer reboots
instead of resuming).
References: https://bugzilla.kernel.org/show_bug.cgi?id=55001
Signed-off-by: Fabio Valentini <fafatheone@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Got this dmesg log on an Acer Aspire 725.
[ 0.256351] ACPI: (supports S0ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S1_] (20130117/hwxface-568)
[ 0.256373] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S2_] (20130117/hwxface-568)
[ 0.256391] S3 S4 S5)
Avoid this interleaving error messages.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch adds a quirk to allow the Sony VGN-FW41E_H to suspend/resume
properly.
References: http://bugs.launchpad.net/bugs/1113547
Signed-off-by: Joseph Salisbury <joseph.salisbury@canonical.com>
Cc: All <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Move some suspend-specific and hibernate-specific code from
acpi_sleep_init() into separate functions to get rid of explicit
#ifdefs in acpi_sleep_init(). Use pr_info() to start and pr_cont()
to continue printing the supported ACPI sleep states line.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The ACPI power resources driver is not very useful, because the only
thing it really does is to restore the state of the power resources
that were "on" before system suspend or hibernation, but that may be
achieved in a different way.
Drop the ACPI power resources driver entirely and add
acpi_resume_power_resources() that will walk the list of all
registered power resources during system resume and turn on the ones
that were "on" before the preceding system suspend or hibernation.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* acpi-general:
ACPI / PNP: Do not crash due to stale pointer use during system resume
ACPI / video: Add "Asus UL30VT" to ACPI video detect blacklist
ACPI: do acpisleep dmi check when CONFIG_ACPI_SLEEP is set
The current acpisleep DMI checks only run when CONFIG_SUSPEND is set.
And this may break hibernation on some platforms when CONFIG_SUSPEND
is cleared.
Move acpisleep DMI check into #ifdef CONFIG_ACPI_SLEEP instead.
[rjw: Added acpi_sleep_dmi_check() and rebased on top of earlier
patches adding entries to acpisleep_dmi_table[].]
References: https://bugzilla.kernel.org/show_bug.cgi?id=45921
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* acpi-general: (38 commits)
ACPI / thermal: _TMP and _CRT/_HOT/_PSV/_ACx dependency fix
ACPI: drop unnecessary local variable from acpi_system_write_wakeup_device()
ACPI: Fix logging when no pci_irq is allocated
ACPI: Update Dock hotplug error messages
ACPI: Update Container hotplug error messages
ACPI: Update Memory hotplug error messages
ACPI: Update CPU hotplug error messages
ACPI: Add acpi_handle_<level>() interfaces
ACPI: remove use of __devexit
ACPI / PM: Add Sony Vaio VPCEB1S1E to nonvs blacklist.
ACPI / battery: Correct battery capacity values on Thinkpads
Revert "ACPI / x86: Add quirk for "CheckPoint P-20-00" to not use bridge _CRS_ info"
ACPI: create _SUN sysfs file
ACPI / memhotplug: bind the memory device when the driver is being loaded
ACPI / memhotplug: don't allow to eject the memory device if it is being used
ACPI / memhotplug: free memory device if acpi_memory_enable_device() failed
ACPI / memhotplug: fix memory leak when memory device is unbound from acpi_memhotplug
ACPI / memhotplug: deal with eject request in hotplug queue
ACPI / memory-hotplug: add memory offline code to acpi_memory_device_remove()
ACPI / memory-hotplug: call acpi_bus_trim() to remove memory device
...
Conflicts:
include/linux/acpi.h (two additions at the end of the same file)
Sony Vaio VPCEB1S1E does not resume correctly without
acpi_sleep=nonvs, so add it to the ACPI sleep blacklist.
References: https://bugzilla.kernel.org/show_bug.cgi?id=48781
Reported-by: Sébastien Wilmet <swilmet@gnome.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The ACPI specificiation would like us to save NVS at hibernation time,
but makes no mention of saving NVS over S3. Not all versions of
Windows do this either, and it is clear that not all machines need NVS
saved/restored over S3. Allow the user to improve their suspend/resume
time by disabling the NVS save/restore at S3 time, but continue to do
the NVS save/restore for S4 as specified.
Signed-off-by: Kristen Carlson Accardi <kristen@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Introduce helper function returning the target sleep state of the
system and use it to move the remaining device power management
functions from sleep.c to device_pm.c.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Two device wakeup management routines in device_pm.c and sleep.c,
acpi_pm_device_run_wake() and acpi_pm_device_sleep_wake(), take a
device pointer argument and use it to obtain the ACPI handle of the
corresponding ACPI namespace node. That handle is then used to get
the address of the struct acpi_device object corresponding to the
struct device passed as the argument.
Unfortunately, that last operation may be costly, because it involves
taking the global ACPI namespace mutex, so it shouldn't be carried
out too often. However, the callers of those routines usually call
them in a row with acpi_pm_device_sleep_state() which also takes that
mutex for the same reason, so it would be more efficient if they ran
acpi_bus_get_device() themselves to obtain a pointer to the struct
acpi_device object in question and then passed that pointer to the
appropriate PM routines.
To make that possible, split each of the PM routines mentioned above
in two parts, one taking a struct acpi_device pointer argument and
the other implementing the current interface for compatibility.
Additionally, change acpi_pm_device_run_wake() to actually return
an error code if there is an error while setting up runtime remote
wakeup for the device.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The ACPI function for setting up devices to do runtime remote
wakeup is now located in drivers/acpi/sleep.c, but
drivers/acpi/device_pm.c is a more logical place for it, so move it
there.
No functional changes should result from this modification.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The ACPI function for choosing device power state is now located
in drivers/acpi/sleep.c, but drivers/acpi/device_pm.c is a more
logical place for it, so move it there.
However, instead of moving the function entirely, move its core only
under a different name and with a different list of arguments, so
that it is more flexible, and leave a wrapper around it in the
original location.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The kerneldoc comments for acpi_pm_device_sleep_state(),
acpi_pm_device_run_wake(), and acpi_pm_device_sleep_wake() are
outdated or otherwise inaccurate and/or don't follow the common
kerneldoc patterns, so fix them.
Additionally, notice that acpi_pm_device_run_wake() should be under
CONFIG_PM_RUNTIME rather than under CONFIG_PM_SLEEP, so fix that too.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Make ACPI power management routines and PCI power management
routines depending on ACPI take device PM QoS flags into account
when deciding what power state to put the device into.
In particular, after this change acpi_pm_device_sleep_state() will
not return ACPI_STATE_D3_COLD as the deepest available low-power
state if PM_QOS_FLAG_NO_POWER_OFF is requested for the device and it
will not require remote wakeup to work for the device in the returned
low-power state if there is at least one PM QoS flags request for the
device, but PM_QOS_FLAG_REMOTE_WAKEUP is not requested for it.
Accordingly, acpi_pci_set_power_state() will refuse to put the
device into D3cold if PM_QOS_FLAG_NO_POWER_OFF is requested for it.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Huang Ying <ying.huang@intel.com>
_GTS and _BFS were added to the suspend/resume flow
in the ACPI 2.0 specification.
Linux dutifully implemented _GTS and _BFS.
We discovered that it was rarely seen in systems
in the field. Further, some of those systems had
AML so bogus that it could never work -- proof that
no other operating system supports _GTS and _BFS.
So we made _GTS and _BFS optional via modparam,
and disabled them by default.
But we've had to complicate some code to keep
this support in the kernel, as these methods are defined
to be evaluated very close to sleep entry and exit.
Indeed, no other AML is ever evaluated with interrupts off.
We have submitted a proposal for _GTS and _BFS
to be officially removed from the ACPI specification
on the next revision. Here we remove it from Linux.
Signed-off-by: Len Brown <len.brown@intel.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Rafael J. Wysocki