Some OMAP interrupt controllers use generic level detection, so
handle_level_irq() is used as the chip type handler.
Allocated IRQ chip type handler doesn't need to set it again because
irq_alloc_domain_generic_chips() has already registered it.
Tested with BeagleBoneBlack Rev C.
Signed-off-by: Milo Kim <milo.kim@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: linux-omap@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Link: http://lkml.kernel.org/r/1450687994-12580-1-git-send-email-milo.kim@ti.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This commit adds support for the TS-4800 interrupt controller. This
controller is instantiated in a companion FPGA, and multiplex interrupts
for other FPGA IPs.
As this component is external to the SoC, the SoC might need to reserve
pins, so this controller is implemented as a platform driver and doesn't
use the IRQCHIP_DECLARE construct.
Signed-off-by: Damien Riegel <damien.riegel@savoirfairelinux.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: kernel@savoirfairelinux.com
Link: http://lkml.kernel.org/r/1450728683-31416-2-git-send-email-damien.riegel@savoirfairelinux.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This is an interrupt-controller implemented in an FPGA, to multiplex
interrupts generated from other IPs. The FPGA usually uses a GPIO as a
parent interrupt controller to notify that one of the multiplexed
interrupts has triggered.
Signed-off-by: Damien Riegel <damien.riegel@savoirfairelinux.com>
Acked-by: Rob Herring <robh@kernel.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: kernel@savoirfairelinux.com
Link: http://lkml.kernel.org/r/1450728683-31416-1-git-send-email-damien.riegel@savoirfairelinux.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The current MSI framework can only support 256 platform MSIs. But on Hisilicon
platform, some network related devices has about 500 wired interrupts.
To support these devices and align with MSI-X increase the maximum to 2048
devices.
Signed-off-by: Ma Jun <majun258@huawei.com>
Cc: <Catalin.Marinas@arm.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: <Will.Deacon@arm.com>
Cc: <mark.rutland@arm.com>
Cc: <marc.zyngier@arm.com>
Cc: <jason@lakedaemon.net>
Cc: <lizefan@huawei.com>
Cc: <huxinwei@huawei.com>
Cc: <dingtianhong@huawei.com>
Cc: <liguozhu@hisilicon.com>
Cc: <guohanjun@huawei.com>
Link: http://lkml.kernel.org/r/1450752442-9392-1-git-send-email-majun258@huawei.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch contain fixes for v2m resources and SPI ranges:
* Fix off-by-one error when set up v2m resource end range in
gicv2m_acpi_init().
* Fix the off-by-one print error for SPI range.
* Use %pR to properly print resource range information.
Both ACPI and DT should now print:
GICv2m: range[mem 0xe1180000-0xe1180fff], SPI[64:319]
Suggested-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Catalin Marinas <Catalin.Marinas@arm.com>
Cc: <hanjun.guo@linaro.org>
Cc: <tomasz.nowicki@linaro.org>
Cc: <graeme.gregory@linaro.org>
Cc: <dhdang@apm.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: <marc.zyngier@arm.com>
Cc: <jason@lakedaemon.net>
Cc: <rjw@rjwysocki.net>
Link: http://lkml.kernel.org/r/1450830263-28914-1-git-send-email-Suravee.Suthikulpanit@amd.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Avoid using hardcoded magics. We have a #define for this number.
No functional changes.
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Eric Anholt <eric@anholt.net>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Lee Jones <lee@kernel.org>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: linux-rpi-kernel@lists.infradead.org
Link: http://lkml.kernel.org/r/1451166444-11044-5-git-send-email-eric@anholt.net
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
On my RPi2 I got a lot of:
unexpected IRQ trap at vector 00
This happens because bcm2836_arm_irqchip_handle_irq() is sometimes
invoked even if the ISR is clear, and this case is not handled.
This patch explicitly handle this case, fixing the kernel complaints
about the bad IRQ lookup.
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Eric Anholt <eric@anholt.net>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Lee Jones <lee@kernel.org>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: linux-rpi-kernel@lists.infradead.org
Link: http://lkml.kernel.org/r/1451166444-11044-4-git-send-email-eric@anholt.net
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The firmware sets the secondaries spinning waiting for a non-NULL
value to show up in the last IPI mailbox.
The original SMP port from the downstream tree was done by Andrea, and
Eric cleaned it up/rewrote it a few times from there.
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Lee Jones <lee@kernel.org>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: linux-rpi-kernel@lists.infradead.org
Link: http://lkml.kernel.org/r/1451166444-11044-3-git-send-email-eric@anholt.net
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The irqchip's register area includes the the setup for the timer's
scaling factors, and for the platform we want a fixed configuration of
these registers.
Signed-off-by: Eric Anholt <eric@anholt.net>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Lee Jones <lee@kernel.org>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: linux-rpi-kernel@lists.infradead.org
Link: http://lkml.kernel.org/r/1451166444-11044-2-git-send-email-eric@anholt.net
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch introduces gicv2m_acpi_init(), which uses information
in MADT GIC MSI frames structure to initialize GICv2m driver.
It also exposes gicv2m_init() function, which simplifies callers
to a single GICv2m init function.
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Tested-by: Duc Dang <dhdang@apm.com>
Acked-by: Rafael J. Wysocki <rjw@rjwysocki.net>
Signed-off-by: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
This patch replaces the struct device_node with struct fwnode_handle
since this structure is common between DT and ACPI.
It also refactors gicv2m_init_one() to prepare for ACPI support.
The only functional change is removing the node name from pr_info.
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Since there will be several places checking if fwnode.type
is equal FWNODE_IRQCHIP, this patch adds a convenient function
for this purpose.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
This patch introduces pci_msi_register_fwnode_provider() for irqchip
to register a callback, to provide a way to determine appropriate MSI
domain for a pci device.
It also introduces pci_host_bridge_acpi_msi_domain(), which returns
the MSI domain of the specified PCI host bridge with DOMAIN_BUS_PCI_MSI
bus token. Then, it is assigned to pci device.
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rjw@rjwysocki.net>
Signed-off-by: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Pull the GIC related updates from Marc Zyngier:
"Not a lot this time (what a relief!), but an interesting series from
Linus Walleij coming out of his work converting the ARM RealView
platforms to DT, and a couple of mundane fixes."
Pull the MSI wire bridge implementation from Marc Zyngier along with
the first user of it. This is infrastructure to support a wired
interrupt to MSI interrupt brigde. The first user is mbigen found in
Hisilicon ARM SoCs.
Add the interrupt controller chip operation functions of mbigen chip.
Signed-off-by: Ma Jun <majun258@huawei.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
For peripheral devices which connect to mbigen,mbigen is a interrupt
controller. So, we create irq domain for each mbigen device and add
mbigen irq domain into irq hierarchy structure.
Signed-off-by: Ma Jun <majun258@huawei.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Mbigen means Message Based Interrupt Generator(MBIGEN).
Its a kind of interrupt controller that collects
the interrupts from external devices and generate msi interrupt.
Mbigen is applied to reduce the number of wire connected interrupts.
As the peripherals increasing, the interrupts lines needed is
increasing much, especially on the Arm64 server SOC.
Therefore, the interrupt pin in GIC is not enough to cover so
many peripherals.
Mbigen is designed to fix this problem.
Mbigen chip locates in ITS or outside of ITS.
Mbigen chip hardware structure shows as below:
mbigen chip
|---------------------|-------------------|
mgn_node0 mgn_node1 mgn_node2
| |-------| |-------|------|
dev1 dev1 dev2 dev1 dev3 dev4
Each mbigen chip contains several mbigen nodes.
External devices can connect to mbigen node through wire connecting way.
Because a mbigen node only can support 128 interrupt maximum, depends
on the interrupt lines number of devices, a device can connects to one
more mbigen nodes.
Also, several different devices can connect to a same mbigen node.
When devices triggered interrupt,mbigen chip detects and collects
the interrupts and generates the MBI interrupts by writing the ITS
Translator register.
To simplify mbigen driver,I used a new conception--mbigen device.
Each mbigen device is initialized as a platform device.
Mbigen device presents the parts(register, pin definition etc.) in
mbigen chip corresponding to a peripheral device.
So from software view, the structure likes below
mbigen chip
|---------------------|-----------------|
mbigen device1 mbigen device2 mbigen device3
| | |
dev1 dev2 dev3
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Ma Jun <majun258@huawei.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Add the mbigen msi interrupt controller bindings document.
This patch based on Mark Rutland's patch
https://lkml.org/lkml/2015/7/23/558
Signed-off-by: Ma Jun <majun258@huawei.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
There is currently a hack in the GIC driver making it possible
to pass the number of GIC instances from the platform-specific
include files and thus override the variable MAX_GIC_NR.
With multiplatform deployments, this will not work as we need
to get rid of the platform-specific include files.
It turns out that this feature is only used by the RealView
platform which has a cascaded GIC. So move the configuration
to Kconfig and bump to 2 instances if we're building for the
RealView. The include file hacks can then be removed.
Tested on the ARM PB11MPCore with its cascaded GIC.
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The GIC has no such thing as interrupt 1020: the last valid ID is
1019, and the range 1020-1023 is reserved - 1023 indicating that
no interrupt is pending. So let's make sure we don't try to handle
this ID.
This bug has been in since the initial GIC code was introduced in
8ad68bbf7a ("[ARM] Add support for ARM RealView board").
Reported-by: Eric Auger <eric.auger@linaro.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
On the error path, the v2m drivers drops the refcount on the parent
node instead of doing it on the node that generated the error.
Humph...
Reported-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Instead of having the irqchip being a static struct, make it part
of the per-instance data so we can assign it a dynamic name. This
has the usable side effect of displaying the GIC with an instance
number as GIC0, GIC1 ... GICn in /proc/interrupts, which is helpful
when debugging cascaded GICs, such as on the ARM PB11MPCore.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The ARM RealView PB11MPCore reference design has some special
bits in a system controller register to set up the GIC in one
of three modes: legacy, new with DCC, new without DCC. The
register is also used to enable FIQ.
Since the platform will not boot unless this register is set
up to "new with DCC" mode, we need a special quirk to be
compiled-in for the RealView platforms.
If we find the right compatible string on the GIC TestChip,
we enable this quirk by looking up the system controller and
enabling the special bits.
We depend on the CONFIG_REALVIEW_DT Kconfig symbol as the old
boardfile code has the same fix hardcoded, and this is only
needed for the attempts to modernize the RealView code using
device tree.
After fixing this, the PB11MPCore boots with device tree
only.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The GIC bindings for the ARM11MPCore need to differentiate between
the GIC on the Test Chip and the one on the evaluation baseboard.
Split the binding in two and define new compatible-strings.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: devicetree@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
We almost have all the needed bits requiredable to create a irq domain
on top of a MSI domain.
For this, we enable a few things:
- the virq is stored in the msi_desc
- device, msi_alloc_info and domain-specific data
are stored in the platform_priv_data structure
- we introduce a new API for platform-msi:
/* Create a MSI-based domain */
struct irq_domain *
platform_msi_create_device_domain(struct device *dev,
unsigned int nvec,
irq_write_msi_msg_t write_msi_msg,
const struct irq_domain_ops *ops,
void *host_data);
/* Allocate MSIs in an MSI domain */
int platform_msi_domain_alloc(struct irq_domain *domain,
unsigned int virq,
unsigned int nr_irqs);
/* Free MSIs from an MSI domain */
void platform_msi_domain_free(struct irq_domain *domain,
unsigned int virq,
unsigned int nvec);
/* Obtain the host data passed to platform_msi_create_device_domain */
void *platform_msi_get_host_data(struct irq_domain *domain);
platform_msi_create_device_domain() is a hybrid of irqdomain creation
and interrupt allocation, creating a domain backed by the MSIs associated
to a device. IRQs can then be allocated in that domain using
platform_msi_domain_alloc().
This now allows a wired irq to MSI bridge to be created.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
To be able to allocate interrupts from the MSI layer down,
add a new msi_domain_populate_irqs entry point.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The .prepare callbacks are so far only called from msi_domain_alloc_irqs.
In order to reuse that code, split that code and create a
msi_domain_prepare_irqs function that the existing code can call into.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
We are soon going to need the MSI layer to call into the domain
allocators. Instead of open coding this, make the standard
irq_domain_alloc_irqs_recursive function available to the MSI
layer.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
As we're going to have multiple paths to allocate/free the
platform-msi private data, factor this out into separate
utility functions.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
MSIs for a given device are normally all allocated in one go.
Make sure the internal code can allocate them one at a time
if required.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The new VMD device driver needs to iterate over a list of
"demultiplexing" interrupts. Protecting that list with a lock is not
possible because the list is also required in code pathes which hold
irq descriptor lock. Therefor the demultiplexing interrupt handler
would create a lock inversion scenario if it calls a demux handler
with the list protection lock held.
A solution for this is to free the irq descriptor via RCU, so the
list can be walked with rcu read lock held.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Keith Busch <keith.busch@intel.com>
Jan Stancek reported that I wrecked things for him by fixing things for
Vladimir :/
His report was due to an UNINTERRUPTIBLE wait getting -EINTR, which
should not be possible, however my previous patch made this possible by
unconditionally checking signal_pending().
We cannot use current->state as was done previously, because the
instruction after the store to that variable it can be changed. We must
instead pass the initial state along and use that.
Fixes: 68985633bc ("sched/wait: Fix signal handling in bit wait helpers")
Reported-by: Jan Stancek <jstancek@redhat.com>
Reported-by: Chris Mason <clm@fb.com>
Tested-by: Jan Stancek <jstancek@redhat.com>
Tested-by: Vladimir Murzin <vladimir.murzin@arm.com>
Tested-by: Chris Mason <clm@fb.com>
Reviewed-by: Paul Turner <pjt@google.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: tglx@linutronix.de
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: hpa@zytor.com
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull timer fixlets from Thomas Gleixner:
"Two trivial fixes which add missing header fileas and forward
declarations so the code will compile even when the magic include
chains are different"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/gic-v3: Add missing include for barrier.h
irqchip/gic-v3: Add missing struct device_node declaration
Pull timer fix from Thomas Gleixner:
"A single fix to unbreak a clocksource driver which has more than 32bit
counter width"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clocksource: Mmio: remove artificial 32bit limitation
Only 2 small fpga driver fixes here, both have been in linux-next for a
while, and resolve some reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlZs8QgACgkQMUfUDdst+ylYnQCfXd9QTIlpJqssNzGZhcgE/CNI
jRgAoIPkV4HkJjbv5TY15oSvxMjHOUo/
=NqHx
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull fpga driver fixes from Greg KH:
"Only two small fpga driver fixes here, both have been in linux-next
for a while, and resolve some reported issues"
* tag 'char-misc-4.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
fpga manager: Fix firmware resource leak on error
fpga manager: remove label
Here are a few staging and IIO driver fixes for 4.4-rc5.
All of them resolve reported problems and have been in linux-next for a
while. Nothing major here, just small fixes where needed.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlZs8XoACgkQMUfUDdst+ylBOACgyDkTu3PMP0JXQkUQps5FFhz2
4gIAoJJei6yppBFqQZpWYIZgY9bt+08q
=stnU
-----END PGP SIGNATURE-----
Merge tag 'staging-4.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver fixes from Greg KH:
"Here are a few staging and IIO driver fixes for 4.4-rc5.
All of them resolve reported problems and have been in linux-next for
a while. Nothing major here, just small fixes where needed"
* tag 'staging-4.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: lustre: echo_copy.._lsm() dereferences userland pointers directly
iio: adc: spmi-vadc: add missing of_node_put
iio: fix some warning messages
iio: light: apds9960: correct ->last_busy count
iio: lidar: return -EINVAL on invalid signal
staging: iio: dummy: complete IIO events delivery to userspace
Here are a number of small USB fixes for 4.4-rc5. All of them have been
in linux-next. The majority are gadget and phy issues, with a few new
quirks and device ids added as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlZs8fkACgkQMUfUDdst+ym/HwCgxdhop3PMk9QxCVaEdxcqv10p
PDkAn0uOW1sdRsHVRhutjcc29+AUJggk
=ybrB
-----END PGP SIGNATURE-----
Merge tag 'usb-4.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB driver fixes from Greg KH:
"Here are a number of small USB fixes for 4.4-rc5. All of them have
been in linux-next. The majority are gadget and phy issues, with a
few new quirks and device ids added as well"
* tag 'usb-4.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (32 commits)
USB: add quirk for devices with broken LPM
xhci: fix usb2 resume timing and races.
usb: musb: fail with error when no DMA controller set
usb: gadget: uvc: fix permissions of configfs attributes
usb: musb: core: Fix pm runtime for deferred probe
usb: phy: msm: fix a possible NULL dereference
USB: host: ohci-at91: fix a crash in ohci_hcd_at91_overcurrent_irq
usb: Quiet down false peer failure messages
usb: xhci: fix config fail of FS hub behind a HS hub with MTT
xhci: Fix memory leak in xhci_pme_acpi_rtd3_enable()
usb: Use the USB_SS_MULT() macro to decode burst multiplier for log message
USB: whci-hcd: add check for dma mapping error
usb: core : hub: Fix BOS 'NULL pointer' kernel panic
USB: quirks: Apply ALWAYS_POLL to all ELAN devices
usb-storage: Fix scsi-sd failure "Invalid field in cdb" for USB adapter JMicron
USB: quirks: Fix another ELAN touchscreen
usb: dwc3: gadget: don't prestart interrupt endpoints
USB: serial: Another Infineon flash loader USB ID
USB: cdc_acm: Ignore Infineon Flash Loader utility
USB: cp210x: Remove CP2110 ID from compatibility list
...
Here are a bunch of small bug fixes for various ARM platforms, nothing
really sticks out this week, most of either fixes bugs in code that was
just added in 4.4, or that has been broken for many years without anyone
noticing.
at91/sama5d2
- fix sama5de hardware setup of sd/mmc interface
- proper selection of pinctrl drivers. PIO4 is necessary for sama5d2
berlin
- fix incorrect clock input for SDIO
exynos
- Fix potential NULL pointer dereference in Exynos PMU driver.
imx
- Fix vf610 SAI clock configuration bug which is discovered by
the newly added master mode support in SAI audio driver.
- Fix buggy L2 cache latency values in vf610 device trees, which may
cause system hang when cpu runs at a higher frequency.
ixp4xx
- fix prototypes for readl/writel functions
ls2080a
- use little-endian register access for GPIO and SDHCI
omap
- Fix clock source for ARM TWD and global timers on am437x
- Always select REGULATOR_FIXED_VOLTAGE for omap2+ instead of
when MACH_OMAP3_PANDORA is selected
- Fix SPI DMA handles for dm816x as only some were mapped
- Fix up mbox cells for dm816x to make mailbox usable
pxa
- use PWM lookup table for all ezx machines
s3c24xx
- Remove incorrect __init annotation from s3c24xx cpufreq driver structures.
versatile
- fix PCI IRQ mapping on Versatile PB
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIVAwUAVmyQMWCrR//JCVInAQIIDA//VyJ2UoTJ2JC3thVP56P/ZXh7Pz8VDqnq
cgoFUio27IeHPSgs+W9qWliOrb+LaXkuOl8CKgepm+Bv7j8Y+uryP4X2rKQ3ZRmy
2f5+uUqAIZ0Co2aJdtG395lY9TKNHl6cPEskcbgL7cjdgj7QBqfIyj22QZbj6yRp
kp8pj+cKXBFRLa5PvePon2w03MA/bLaP30VzKCSL1zchcs52rxekU694V3ISNa63
eshyyKf354Sl9hP4Y8xCdl/mboymKzQxEGDQS/Fcb8h/OQ3djoh+7EKdVbdyZ2A7
phgfazd2aE7wQ5GVIkMNV/MzGHj9xpiD4Z1Hi/2E8WdzuXJTRicS4bJihRAIualt
H1FOEdgqT+xS4JUYxAvl46fwwqcFJfixtGgKka27sJTtk+Y1kHjASWvueZKlHMIK
ln9CF7PoecF0InQaY2N8Vy05Qcp5MuoB/0v+XlftI0sAtIXNeo142H2NQZCsO+1U
bJDyb5E4z06jzqk7IOK4/AKyEAV9KZPDws+ZxcNH/faPT10epK7MeZdetbD7b8q3
pkY7s5iXV8uBox7FtHoamrlMFgAzN9Qh0E4bcw70aKaJZZ02ozTXCvJIKjoIPMne
FsvidQToznqbA2RSXpxRQrcXrMxvURaPCRBe7CxrCoynmhIxd4UHND2HJ4OG645z
4SAGOzOlZKM=
=fgEd
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Arnd Bergmann:
"Here are a bunch of small bug fixes for various ARM platforms, nothing
really sticks out this week, most of either fixes bugs in code that
was just added in 4.4, or that has been broken for many years without
anyone noticing.
at91/sama5d2:
- fix sama5de hardware setup of sd/mmc interface
- proper selection of pinctrl drivers. PIO4 is necessary for sama5d2
berlin:
- fix incorrect clock input for SDIO
exynos:
- Fix potential NULL pointer dereference in Exynos PMU driver.
imx:
- Fix vf610 SAI clock configuration bug which is discovered by the
newly added master mode support in SAI audio driver.
- Fix buggy L2 cache latency values in vf610 device trees, which may
cause system hang when cpu runs at a higher frequency.
ixp4xx:
- fix prototypes for readl/writel functions
ls2080a:
- use little-endian register access for GPIO and SDHCI
omap:
- Fix clock source for ARM TWD and global timers on am437x
- Always select REGULATOR_FIXED_VOLTAGE for omap2+ instead of when
MACH_OMAP3_PANDORA is selected
- Fix SPI DMA handles for dm816x as only some were mapped
- Fix up mbox cells for dm816x to make mailbox usable
pxa:
- use PWM lookup table for all ezx machines
s3c24xx:
- Remove incorrect __init annotation from s3c24xx cpufreq driver
structures.
versatile:
- fix PCI IRQ mapping on Versatile PB"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ls2080a/dts: Add little endian property for GPIO IP block
dt-bindings: define little-endian property for QorIQ GPIO
ARM64: dts: ls2080a: fix eSDHC endianness
ARM: dts: vf610: use reset values for L2 cache latencies
ARM: pxa: use PWM lookup table for all machines
ARM: dts: berlin: add 2nd clock for BG2Q sdhci0 and sdhci1
ARM: dts: berlin: correct BG2Q's sdhci2 2nd clock
ARM: dts: am4372: fix clock source for arm twd and global timers
ARM: at91: fix pinctrl driver selection
ARM: at91/dt: add always-on to 1.8V regulator
ARM: dts: vf610: fix clock definition for SAI2
ARM: imx: clk-vf610: fix SAI clock tree
ARM: ixp4xx: fix read{b,w,l} return types
irqchip/versatile-fpga: Fix PCI IRQ mapping on Versatile PB
ARM: OMAP2+: enable REGULATOR_FIXED_VOLTAGE
ARM: dts: add dm816x missing spi DT dma handles
ARM: dts: add dm816x missing #mbox-cells
cpufreq: s3c24xx: Do not mark s3c2410_plls_add as __init
ARM: EXYNOS: Fix potential NULL pointer access in exynos_sys_powerdown_conf
- opal-irqchip: Fix double endian conversion from Alistair Popple
- cxl: Set endianess of kernel contexts from Frederic Barrat
- sbc8641: drop bogus PHY IRQ entries from DTS file from Paul Gortmaker
- Revert "powerpc/eeh: Don't unfreeze PHB PE after reset" from Andrew Donnellan
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=bYj2
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.4-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
- opal-irqchip: Fix double endian conversion from Alistair Popple
- cxl: Set endianess of kernel contexts from Frederic Barrat
- sbc8641: drop bogus PHY IRQ entries from DTS file from Paul Gortmaker
- Revert "powerpc/eeh: Don't unfreeze PHB PE after reset" from Andrew
Donnellan
* tag 'powerpc-4.4-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
Revert "powerpc/eeh: Don't unfreeze PHB PE after reset"
powerpc/sbc8641: drop bogus PHY IRQ entries from DTS file
cxl: Set endianess of kernel contexts
powerpc/opal-irqchip: Fix double endian conversion
Merge misc fixes from Andrew Morton:
"17 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
MIPS: fix DMA contiguous allocation
sh64: fix __NR_fgetxattr
ocfs2: fix SGID not inherited issue
mm/oom_kill.c: avoid attempting to kill init sharing same memory
drivers/base/memory.c: prohibit offlining of memory blocks with missing sections
tmpfs: fix shmem_evict_inode() warnings on i_blocks
mm/hugetlb.c: fix resv map memory leak for placeholder entries
mm: hugetlb: call huge_pte_alloc() only if ptep is null
kernel: remove stop_machine() Kconfig dependency
mm: kmemleak: mark kmemleak_init prototype as __init
mm: fix kerneldoc on mem_cgroup_replace_page
osd fs: __r4w_get_page rely on PageUptodate for uptodate
MAINTAINERS: make Vladimir co-maintainer of the memory controller
mm, vmstat: allow WQ concurrency to discover memory reclaim doesn't make any progress
mm: fix swapped Movable and Reclaimable in /proc/pagetypeinfo
memcg: fix memory.high target
mm: hugetlb: fix hugepage memory leak caused by wrong reserve count
Pull parisc fixes from Helge Deller:
"Fix the boot crash on Mako machines with Huge Pages, prevent a panic
with SATA controllers (and others) by correctly calculating the IOMMU
space, hook up the mlock2 syscall and drop unneeded code in the parisc
pci code"
* 'parisc-4.4-3' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Disable huge pages on Mako machines
parisc: Wire up mlock2 syscall
parisc: Remove unused pcibios_init_bus()
parisc iommu: fix panic due to trying to allocate too large region
Pull block layer fixes from Jens Axboe:
"A set of fixes for the current series. This contains:
- A bunch of fixes for lightnvm, should be the last round for this
series. From Matias and Wenwei.
- A writeback detach inode fix from Ilya, also marked for stable.
- A block (though it says SCSI) fix for an OOPS in SCSI runtime power
management.
- Module init error path fixes for null_blk from Minfei"
* 'for-linus' of git://git.kernel.dk/linux-block:
null_blk: Fix error path in module initialization
lightnvm: do not compile in debugging by default
lightnvm: prevent gennvm module unload on use
lightnvm: fix media mgr registration
lightnvm: replace req queue with nvmdev for lld
lightnvm: comments on constants
lightnvm: check mm before use
lightnvm: refactor spin_unlock in gennvm_get_blk
lightnvm: put blks when luns configure failed
lightnvm: use flags in rrpc_get_blk
block: detach bdev inode from its wb in __blkdev_put()
SCSI: Fix NULL pointer dereference in runtime PM
- Update the linker script to use L1_CACHE_BYTES instead of hard-coded
64. We recently changed L1_CACHE_BYTES to 128
- Improve race condition reporting on set_pte_at() and change the BUG to
WARN_ONCE. With hardware update of the accessed/dirty state, we need
to ensure that set_pte_at() does not inadvertently override hardware
updated state. The patch also makes the checks ignore !pte_valid() new
entries
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=L6aC
-----END PGP SIGNATURE-----
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Catalin Marinas:
- Update the linker script to use L1_CACHE_BYTES instead of hard-coded
64. We recently changed L1_CACHE_BYTES to 128
- Improve race condition reporting on set_pte_at() and change the BUG
to WARN_ONCE. With hardware update of the accessed/dirty state, we
need to ensure that set_pte_at() does not inadvertently override
hardware updated state. The patch also makes the checks ignore
!pte_valid() new entries
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: Improve error reporting on set_pte_at() checks
arm64: update linker script to increased L1_CACHE_BYTES value
Milo Kim