Make the default autosuspend delay configurable at build time.
This is useful for systems that require a non-standard value as
it avoids relying on the command line being properly set.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Refactor the code in charge of looking up the USB PHY when no platdata
is provided. Attempt to get a generic USB PHY first, then look for a
legacy USB PHY through device-tree and finally get any registered PHY
with the correct type.
This way, only a single USB PHY is obtained and the flow is easier to
understand and follow.
All error pointers (except for EPROBE_DEFER) are considered as PHY
not found.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to the chipidea driver bindings, the USB PHY is specified via
the "phys" phandle node. However, this only takes effect for USB PHYs
that use the common PHY framework. For legacy USB PHYs, a simple lookup
based on the USB PHY type is done instead.
This does not play out well when more than one USB PHY is registered,
since the first registered PHY matching the type will always be
returned regardless of what the driver was bound to.
Fix this by looking up the PHY based on the "phys" phandle node.
Although generic PHYs are rather matched by their "phys-name" and not
the "phys" phandle directly, there is no helper for similar lookup on
legacy PHYs and it's probably not worth the effort to add it.
When no legacy USB PHY is found by phandle, fallback to grabbing any
registered USB2 PHY. This ensures backward compatibility if some users
were actually relying on this mechanism.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support to set the power line polarity for i.MX SoCs.
To let the USB controller control the power it may be necessary to
configure the polarity of the power line. So far the polarity was
configured by Bootloader or alternatively the power line was muxed
as gpio and driven by a regulator.
Also make use of of_property_read_bool.
Signed-off-by: Philipp Puschmann <philipp.puschmann@emlix.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Those 2 headers files are not required now.
Signed-off-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ChipIdea's platform device need to be unregistered on Tegra's driver
module removal.
Fixes: dfebb5f43a ("usb: chipidea: Add support for Tegra20/30/114/124")
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Peter Chen <peter.chen@nxp.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hedberg says:
====================
Here's the main bluetooth-next pull request for the 5.1 kernel.
- Fixes & improvements to mediatek, hci_qca, btrtl, and btmrvl HCI drivers
- Fixes to parsing invalid L2CAP config option sizes
- Locking fix to bt_accept_enqueue()
- Add support for new Marvel sd8977 chipset
- Various other smaller fixes & cleanups
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
On Chrome OS we want to use USBguard to potentially limit access to USB
devices based on policy. We however to do not want to wait for userspace to
come up before initializing fixed USB devices to not regress our boot
times.
This patch adds option to instruct the kernel to only authorize devices
connected to the internal ports. Previously we could either authorize
all or none (or, by default, we'd only authorize wired devices).
The behavior is controlled via usbcore.authorized_default command line
option.
Signed-off-by: Dmitry Torokhov <dtor@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are a couple of new device ids for 5.1-rc1.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----
iHQEABYIAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCXG7PogAKCRALxc3C7H1l
CLtbAP9N7qnHiOflSg8sK3E4hBI5ZaVKQuJwObEOMJY+s6jeYwD1E3sbyWKGHu+2
R8Px/FbKC3JWMUIhO7bVlyvsQDcQAA==
=hG64
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-5.1-rc1-2' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Johan writes:
USB-serial fixes for 5.1-rc1
Here are a couple of new device ids for 5.1-rc1.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
* tag 'usb-serial-5.1-rc1-2' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: ftdi_sio: add ID for Hjelmslund Electronics USB485
USB: serial: cp210x: add ID for Ingenico 3070
Here are the USB-serial updates for 5.1-rc1, including:
- support for the last three GPIOs on cp2102n devices
- gpio support for cp2104
- support for using cp210x gpios with autosuspend
- proper error handling for unsupported cp2105 line speeds
Included is also a new modem device id.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCXG7M3AAKCRALxc3C7H1l
CBUpAQD/N1G1G38alGS0zwn/u9krsVyLm5Y1gK8MWXvpkcGBXwEAoSYrMjoRAAdR
Ks4rQdSyYonbE3zENXp5d3beCRM4pQY=
=GQ5N
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-5.1-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Johan writes:
USB-serial updates for 5.1-rc1
Here are the USB-serial updates for 5.1-rc1, including:
- support for the last three GPIOs on cp2102n devices
- gpio support for cp2104
- support for using cp210x gpios with autosuspend
- proper error handling for unsupported cp2105 line speeds
Included is also a new modem device id.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
* tag 'usb-serial-5.1-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: option: add Telit ME910 ECM composition
USB: serial: cp210x: fix GPIO in autosuspend
USB: serial: cp210x: add minimum baud rate for CP2105 SCI
USB: serial: cp210x: add GPIO support for CP2104
USB: serial: cp210x: support all gpios on CP2102N QFN28 package
Commit 1a2f474d32 handles block _reads_ separately with plain-I2C
adapters, but the problem described with regmap-i2c not handling
SMBus block transfers (i.e. read and writes) correctly also exists
with writes.
As workaround, this patch adds a block write function the same way
1a2f474d32 adds a block read function.
Fixes: 1a2f474d32 ("usb: typec: tps6598x: handle block reads separately with plain-I2C adapters")
Fixes: 0a4c005bd1 ("usb: typec: driver for TI TPS6598x USB Power Delivery controllers")
Signed-off-by: Nikolaus Voss <nikolaus.voss@loewensteinmedical.de>
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fix enables USB role feature on intel commercial nuc
platform which is based on Kabylake chipset.
Signed-off-by: Balaji Manoharan <m.balaji@intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix build warning when building drivers/usb/host/xhci-mem.o with W=1 due
to missing prototype for xhci_free_virt_devices_depth_first.
This function is only used in xhci-mem.c so just make it static.
Signed-off-by: Jean-Philippe Menil <jpmenil@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The member @parent of xhci_regset struct is not used in fact,
so remove it
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During initialization, the host and super-speed power domains will
contain an ERR_PTR() encoded error code rather than being NULL. To
avoid a crash, use a !IS_ERR_OR_NULL() condition during cleanup.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Fixes: 6494a9ad86 ("usb: xhci: tegra: Add genpd support")
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All users of dma_declare_coherent want their allocations to be
exclusive, so default to exclusive allocations.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If an interface has an associated devicetree node with status disabled,
do not register the device. This is useful for boards with a built-in
multifunction USB device where some functions are broken or otherwise
undesired.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All the code paths that lead to the return statement are where
match is always true, hence the check to see if it is true is
redundant and can be removed.
Detected by CoverityScan, CID#14769672 ("Logically dead code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Current GPIO code in cp210x fails to take USB autosuspend into account,
making it practically impossible to use GPIOs with autosuspend enabled
without user configuration. Fix this like for ftdi_sio in a previous patch.
Tested on a CP2102N.
Signed-off-by: Karoly Pados <pados@pados.hu>
Fixes: cf5276ce78 ("USB: serial: cp210x: Adding GPIO support for CP2105")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
In case the "linux,extcon-name" property is defined but device itself
is not ready, defer the probe.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
'rv' is the correct return value, pass it upstream instead of 0
Fixes: 17d80d562f ("USB: autosuspend for cdc-wdm")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/usb/host/oxu210hp-hcd.c: In function 'scan_periodic':
drivers/usb/host/oxu210hp-hcd.c:2256:13: warning:
variable 'uframes' set but not used [-Wunused-but-set-variable]
drivers/usb/host/oxu210hp-hcd.c: In function 'oxu_urb_enqueue':
drivers/usb/host/oxu210hp-hcd.c:2835:6: warning:
variable 'transfer_buffer_length' set but not used [-Wunused-but-set-variable]
They are never used since introduction.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a spelling mistake in a dev_err message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make use of the struct_size() helper instead of an open-coded version
in order to avoid any potential type mistakes, in particular in the
context in which this code is being used.
So, change the following form:
sizeof(*packet_desc) + (sizeof(packet_desc->PacketLength[0]) * seg->isoc_frame_count)
to :
struct_size(packet_status, PacketStatus, seg->isoc_frame_count);
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
struct boo entry[];
};
size = sizeof(struct foo) + count * sizeof(struct boo);
instance = kzalloc(size, GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
instance = kzalloc(struct_size(instance, entry, count), GFP_KERNEL);
Notice that, in this case, variable len is not necessary, hence
it is removed.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
struct boo entry[];
};
size = sizeof(struct foo) + count * sizeof(struct boo);
instance = kzalloc(size, GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
instance = kzalloc(struct_size(instance, entry, count), GFP_KERNEL);
Notice that, in this case, variable size is not necessary, hence
it is removed.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The return from the call to fwnode_property_read_u16_array is int,
it can be a negative error code however this is being assigned to
an size_t variable 'nval', hence the check is always false.
Fix this by making 'nval' an int.
Detected by Coccinelle ("Unsigned expression compared with
zero: nval < 0")
Fixes: 96a6d031ca ("usb: typec: mux: Find the muxes by also matching against the device node")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DaVinci SoC updates for v5.1 (part 2)
This pull request contains changes needed to help get rid of
hard-coded GPIO base value passed from DaVinci platform data.
The OHCI related changes also help by moving over-current support
from board-files to OHCI driver making future DT-coversion easy.
The OHCI parts are acked by its maintainer.
* tag 'davinci-for-v5.1/soc-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
usb: ohci-da8xx: remove unused callbacks from platform data
ARM: davinci: da830-evm: remove legacy usb helpers
ARM: davinci: omapl138-hawk: remove legacy usb helpers
usb: ohci-da8xx: add vbus and overcurrent gpios
ARM: davinci: da830-evm: use gpio lookup entries for usb gpios
ARM: davinci: omapl138-hawk: use gpio lookup entries for usb gpios
usb: ohci-da8xx: add a helper pointer to &pdev->dev
usb: ohci-da8xx: add a new line after local variables
ARM: davinci: da850-evm: use GPIO hogs instead of the legacy API
ARM: davinci: mityomapl138: use device properties for at24 eeprom
ARM: davinci: mityomapl138: use nvmem notifiers
ARM: davinci: remove dead code related to MAC address reading
ARM: davinci: sffsdr: use device properties for at24 eeprom
ARM: davinci: sffsdr: fix the at24 eeprom device name
ARM: davinci: dm646x-evm: use device properties for at24 eeprom
ARM: davinci: dm644x-evm: use device properties for at24 eeprom
ARM: davinci: da830-evm: use device properties for at24 eeprom
ARM: davinci: dm365-evm: use device properties for at24 eeprom
ARM: davinci: mityomapl138: don't read the MAC address from machine code
ARM: davinci: da850-evm: remove dead MTD code
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This adds the USB ID of the Hjelmslund Electronics USB485 Iso stick.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Dwc3 now works on TI's AM6xx platforms. Also on dwc3 we have a few
changes which improve request cancellation and some improvements to
how we print to the trace buffer.
Renesas_usb3 got support for r8a774c0 device.
Dwc2 got scatter-gather support.
Apart from these, the usual set of minor fixes and all sorts of small
details.
-----BEGIN PGP SIGNATURE-----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=4fTL
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
USB: changes for v5.1 merge window
Dwc3 now works on TI's AM6xx platforms. Also on dwc3 we have a few
changes which improve request cancellation and some improvements to
how we print to the trace buffer.
Renesas_usb3 got support for r8a774c0 device.
Dwc2 got scatter-gather support.
Apart from these, the usual set of minor fixes and all sorts of small
details.
* tag 'usb-for-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb: (40 commits)
usb: phy: twl6030-usb: fix possible use-after-free on remove
usb: misc: usbtest: add super-speed isoc support
usb: dwc3: Reset num_trbs after skipping
usb: dwc3: gadget: don't enable interrupt when disabling endpoint
fotg210-udc: pass struct device to DMA API functions
fotg210-udc: remove a bogus dma_sync_single_for_device call
usb: gadget: Change Andrzej Pietrasiewicz's e-mail address
usb: f_fs: Avoid crash due to out-of-scope stack ptr access
usb: dwc3: haps: Workaround matching VID PID
usb: gadget: f_fs: preserve wMaxPacketSize across usb_ep_autoconfig() call
usb: gadget: move non-super speed code out of usb_ep_autoconfig_ss()
usb: gadget: function: sync f_uac1 ac header baInterfaceNr
usb: dwc2: gadget: Add scatter-gather mode
usb: gadget: fix various indentation issues
usb: dwc2: Fix EP TxFIFO number setting
udc: net2280: Fix net2280_disable
USB: gadget: Improve kerneldoc for usb_ep_dequeue()
usb: dwc3: debug: purge usage of strcat
usb: dwc3: trace: pass trace buffer size to decoding functions
usb: dwc3: gadget: remove DWC3_EP_END_TRANSFER_PENDING
...
When the connections are defined in firmware, struct
device_connection will have the fwnode member pointing to
the device node (struct fwnode_handle) of the requested
device, and the endpoint will not be used at all in that
case.
Acked-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the connections are defined in firmware, struct
device_connection will have the fwnode member pointing to
the device node (struct fwnode_handle) of the requested
device, and the endpoint will not be used at all in that
case.
Acked-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the connections are defined in firmware, struct
device_connection will have the fwnode member pointing to
the device node (struct fwnode_handle) of the requested
device, and the endpoint will not be used at all in that
case.
Acked-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Jun Li <jun.li@nxp.com>
Tested-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since with accessory modes there is no need for additional
identification when requesting a handle to the mux, we can
replace the second parameter that is passed to the
typec_mux_get() function with a pointer to alternate mode
description structure, and simply passing NULL with
accessory modes.
This change means the naming of the mux device connections
can be updated. Alternate and Accessory Modes will both be
handled with muxes named "mode-switch", and the orientation
switches will be named "orientation-switch".
Future identification of the alternate modes will be later
done using device property "svid" of the mux.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To prevent loading of the driver when the PD controller is
still in some operational mode that the driver does not
support, checking the mode in driver probe callback
function.
TI PD controllers may be in undefined mode of operation
for example when the application code (firmware) is
completely missing.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tcpm_update_source_capabilities() and tcpm_update_sink_capabilities()
are not used anywhere, and I don't recall why I introduced those functions
in the first place. Effectively that means that we don't know if they even
work, or ever did. Lets remove them.
Reported-by: Kyle Tso <kyletso@google.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Kyle Tso <kyletso@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch
cases where we are expecting to fall through.
This patch fixes the following warning:
drivers/usb/musb/musb_host.c: In function ‘musb_advance_schedule’:
drivers/usb/musb/musb_host.c:374:7: warning: this statement may fall through [-Wimplicit-fallthrough=]
if (qh->mux == 1) {
^
drivers/usb/musb/musb_host.c:383:3: note: here
case USB_ENDPOINT_XFER_ISOC:
^~~~
Warning level 3 was used: -Wimplicit-fallthrough=3
Notice that, in this particular case, the code comment is modified
in accordance with what GCC is expecting to find.
This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In remove(), use cancel_delayed_work_sync() to cancel the
delayed work. Otherwise there's a chance that this work
will continue to run until after the device has been removed.
This issue was detected with the help of Coccinelle.
Cc: Tony Lindgren <tony@atomide.com>
Cc: Bin Liu <b-liu@ti.com>
Fixes: b6a619a883 ("usb: phy: Check initial state for twl6030")
Signed-off-by: Sven Van Asbroeck <TheSven73@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The calculation of packet number within microframe is different between
high-speed and super-speed endpoint, we add support for super-speed
in this patch.
Cc: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Currently req->num_trbs is not reset after the TRBs are skipped and
processed from the cancelled list. The gadget driver may reuse the
request with an invalid req->num_trbs, and DWC3 will incorrectly skip
trbs. To fix this, simply reset req->num_trbs to 0 after skipping
through all of them.
Fixes: c3acd59014 ("usb: dwc3: gadget: use num_trbs when skipping TRBs on ->dequeue()")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Since we're disabling the endpoint anyway, we don't worry about
getting endpoint command completion interrupt.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch does not change any functionality.
Cc: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: Oliver Neukum <oneukum@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A statement is indented too deeply, fix this by removing a tab.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are two users upstream which register external callbacks for
switching the port power on/off and overcurrent protection. Both
users only use two GPIOs for that. Instead of having that functionality
in the board files, move the logic into the OHCI driver - including
the interrupt handler for overcurrent detection.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Add a helper pointer to &pdev->dev. This improves readability by
removing all the &pdev->dev dereferencing.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Add a new line after local variables. This improves the coding style.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
The Kconfig entry previously depended on USB_OTG_BLACKLIST_HUB
unconditionally, which is an option that is only available when
CONFIG_USB is enabled. However, the USB IP in the JZ4740 SoC does not
support host mode, only gadget mode, so it makes sense to allow it to
build when CONFIG_USB is not set.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Depending on MACH_JZ4740 prevent us from creating a generic kernel that
works on more than one MIPS board. Instead, we just depend on MIPS being
set.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for probing the driver from devicetree.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A return statement is indented one level too far, fix this by removing
a tab.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The DMA API generally relies on a struct device to work properly, and
only barely works without one for legacy reasons. Pass the easily
available struct device from the platform_device to remedy this.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
dma_map_single already transfers ownership to the device.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
My @samusung.com address is going to cease existing soon, so change it to
an address which can actually be used to contact me.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Since the 5.0 merge window opened, I've been seeing frequent
crashes on suspend and reboot with the trace:
[ 36.911170] Unable to handle kernel paging request at virtual address ffffff801153d660
[ 36.912769] Unable to handle kernel paging request at virtual address ffffff800004b564
...
[ 36.950666] Call trace:
[ 36.950670] queued_spin_lock_slowpath+0x1cc/0x2c8
[ 36.950681] _raw_spin_lock_irqsave+0x64/0x78
[ 36.950692] complete+0x28/0x70
[ 36.950703] ffs_epfile_io_complete+0x3c/0x50
[ 36.950713] usb_gadget_giveback_request+0x34/0x108
[ 36.950721] dwc3_gadget_giveback+0x50/0x68
[ 36.950723] dwc3_thread_interrupt+0x358/0x1488
[ 36.950731] irq_thread_fn+0x30/0x88
[ 36.950734] irq_thread+0x114/0x1b0
[ 36.950739] kthread+0x104/0x130
[ 36.950747] ret_from_fork+0x10/0x1c
I isolated this down to in ffs_epfile_io():
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/drivers/usb/gadget/function/f_fs.c#n1065
Where the completion done is setup on the stack:
DECLARE_COMPLETION_ONSTACK(done);
Then later we setup a request and queue it, and wait for it:
if (unlikely(wait_for_completion_interruptible(&done))) {
/*
* To avoid race condition with ffs_epfile_io_complete,
* dequeue the request first then check
* status. usb_ep_dequeue API should guarantee no race
* condition with req->complete callback.
*/
usb_ep_dequeue(ep->ep, req);
interrupted = ep->status < 0;
}
The problem is, that we end up being interrupted, dequeue the
request, and exit.
But then the irq triggers and we try calling complete() on the
context pointer which points to now random stack space, which
results in the panic.
Alan Stern pointed out there is a bug here, in that the snippet
above "assumes that usb_ep_dequeue() waits until the request has
been completed." And that:
wait_for_completion(&done);
Is needed right after the usb_ep_dequeue().
Thus this patch implements that change. With it I no longer see
the crashes on suspend or reboot.
This issue seems to have been uncovered by behavioral changes in
the dwc3 driver in commit fec9095bde ("usb: dwc3: gadget:
remove wait_end_transfer").
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Zeng Tao <prime.zeng@hisilicon.com>
Cc: Jack Pham <jackp@codeaurora.org>
Cc: Thinh Nguyen <thinh.nguyen@synopsys.com>
Cc: Chen Yu <chenyu56@huawei.com>
Cc: Jerry Zhang <zhangjerry@google.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Vincent Pelletier <plr.vincent@gmail.com>
Cc: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Linux USB List <linux-usb@vger.kernel.org>
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
It's not needed. Moving everything from it to trace.c.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Because of UCSI, we have to support alt mode enter/exit
reporting even when there is no alt mode driver bind to the
alt mode device. With UCSI a firmware handles the alternate
modes, and the modes are entered automatically from OS PoW.
Changing typec_altmode_update_active() so that the driver
module ref count is incremented/decremented only if there
really is a driver for the alt mode. That avoids a NULL
pointer dereference from happening when the driver is
missing.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The helpers used for reading and writing the pin assignment
from and to the Configuration VDO will be useful in GPU
drivers, and also UCSI driver after DisplayPort alt mode
support is added to it.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit f13912d3f0 introduced changes to the usb_choose_configuration function
to better support USB Audio UAC3-compatible devices. However, there are a few
problems with this patch. First of all, it adds new "if" clauses in the middle
of an existing "if"/"else if" tree, which obviously breaks pre-existing logic.
Secondly, since it continues iterating over configurations in one of the branches,
other code in the loop can choose an unintended configuration. Finally,
if an audio device's first configuration is UAC3-compatible, and there
are multiple UAC3 configurations, the second one would be chosen, due to
the first configuration never being checked for UAC3-compatibility.
Commit ff2a8c532c tries to fix the second issue, but it goes about it in a
somewhat unnecessarily convoluted way, in my opinion, and does nothing
to fix the first or the last one.
This patch tries to rectify problems described by essentially rewriting
code introduced in f13912d3f0. Notice the code was moved to *before*
the "if"/"else if" tree.
Signed-off-by: Nikolay Yakimov <root@livid.pp.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On plug-in of my USB-C device, its USB_SS_PORT_LS_SS_INACTIVE
link state bit is set. Greping all the kernel for this bit shows
that the port status requests a warm-reset this way.
This just happens, if its the only device on the root hub, the hub
therefore resumes and the HCDs status_urb isn't yet available.
If a warm-reset request is detected, this sets the hubs event_bits,
which will prevent any auto-suspend and allows the hubs workqueue
to warm-reset the port later in port_event.
Signed-off-by: Jan-Marek Glogowski <glogow@fbihome.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is how this device appears in kernel log:
usb 3-1: new full-speed USB device number 18 using xhci_hcd
usb 3-1: New USB device found, idVendor=0b00, idProduct=3070
usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 3-1: Product: Ingenico 3070
usb 3-1: Manufacturer: Silicon Labs
usb 3-1: SerialNumber: 0001
Apparently this is a POS terminal with embedded USB-to-Serial converter.
Cc: stable@vger.kernel.org
Signed-off-by: Ivan Mironov <mironov.ivan@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Add minimum baud rate to the cp210x driver.
According to the datasheet for CP2105, the SCI supports 2400 as the
lowest baud rate. As this is not heeded in the current code, an error
message 'failed set req 0x1e size 4 status: -32' when trying to set a
lower baud rate such as 300.
The other cp210x models to date supports a minimum baud rate of 300.
Signed-off-by: Johanna Abrahamsson <johanna.abrahamsson@afconsult.com>
[ johan: simplify min_speed init, move clamp after comment, and drop
unused serial-data pointer from cp210x_get_actual_rate() ]
Signed-off-by: Johan Hovold <johan@kernel.org>
i.MX6QP and i.MX7D platform use a PCIe controller with the same VID and
PID as this USB controller. The system may incorrectly match this driver
to that PCIe controller. To workaround this, specifically use class type
USB with PCI device ID to prevent incorrect driver matching.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
usb_ep_autoconfig() treats the passed descriptor as if it were an fs
descriptor. In particular, for bulk endpoints, it clips wMaxPacketSize
to 64. This patch preserves the original value.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The moved code refers to non-super speed endpoints only. This patch also
makes the comment stress the fact, that autoconfigured descriptor might
need some adjustments.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
f_uac1 audio control header descriptor default set
baInterfaceNr[]={1,2}, but usb gadget make a configuration descriptor
with more interfaces combination, it can not confirm f_uac1 function
linked first. So always keep baInterfaceNr[]={1,2} is correct, and it
is necessary to sync baInterfaceNr[] with usb_interface_id() value.
Signed-off-by: Liang Shengjun <liangshengjun@hisilicon.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch adds support for transferring requests, which are
non-contiguous in physical memory, i.e. the data buffer is described by
a scatter-list. This allows transferring large requests without relying
on error-prone contiguous buffer allocations. This way of allocating
requests is already implemented in functionfs and TCM USB functions and
automatically used if UDC driver advertises scatter-gather suppport.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
[mszyprow: fixed null pointer issue, rewrote commit message]
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
There are a bunch of various indentation issues, clean these up.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In case when some EP IN is frequently reused, i.e. enabled/disabled by
function driver. It is required to clear TxFIFO number field in DIEPCTL
register before setting new number. Otherwise there is probability to
have same TxFIFO number for different EP's because of OR operator.
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
A reset e.g. calling ep_reset_338x() can happen while endpoints
are enabled. The ep_reset_338x() sets ep->desc = NULL to mark
endpoint being invalid. A subsequent call of net2280_disable will
fail and return -EINVAL to parent function usb_ep_disable(),
which will fail, too, and do not set the member ep->enabled = false.
See:
https://elixir.bootlin.com/linux/v5.0-rc5/source/drivers/usb/gadget/udc/core.c#L139
This fix ignores dp->desc and allows net2280_disable() to succeed.
Subsequent calls to usb_ep_enable()/usb_ep_disable() succeeds.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Guido Kiener <guido.kiener@rohde-schwarz.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Commit bf594c1070 ("USB: gadget: Document that certain ep operations
can be called in interrupt context") documented that usb_ep_dequeue()
may be called in a non-process context. It follows that the routine
must not sleep or wait for events.
However, the routine's existing kerneldoc seems to imply that it will
wait until the request being cancelled has fully completed. This is
not so, and thus the comment needs to be improved. Misunderstanding
this point may very well have been responsible for a bug recently
uncovered in the f_fs function.
The updated comment explicitly says that the routine may return before
the request's completion handler is called.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: John Stultz <john.stultz@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
No real need for bidi support once the OSD code is gone.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Due to the patch that makes TMF handling synchronous the
write_pending_status() callback function is no longer called. Hence remove
it.
Acked-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Reviewed-by: Andy Grover <agrover@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Bryant G. Ly <bryantly@linux.vnet.ibm.com>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Cc: Mike Christie <mchristi@redhat.com>
Cc: Himanshu Madhani <himanshu.madhani@qlogic.com>
Cc: Quinn Tran <quinn.tran@qlogic.com>
Cc: Saurav Kashyap <saurav.kashyap@qlogic.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Juergen Gross <jgross@suse.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The CP2104 chips feature 4 controllable GPIO pins, which are similar to
the ones on CP2102N chip (output-only when push-pull, output or
simulated input mode when open-drain).
Add support for the GPIO pins for cp210x driver. The pin get/set routine
is shared with CP2102N, but the pinconf initialization code is not
shared because the acquisition of GPIO configuration in OTP ROM is
similar to CP2105, not CP2102N.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Johan Hovold <johan@kernel.org>
Instead of assuming that our buffer is big enough, let's pass the
buffer size around so printing functions can make sure they won't
overflow the buffer.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
It is better to initialize the variable 'cfgno' in the for loop than
at the current place.
Signed-off-by: Suwan Kim <suwan.kim027@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that we modified the code to fix a race condition, it's clear that
DWC3_EP_END_TRANSFER_PENDING is unnecessary, considering that
DWC3_EP_TRANSFER_STARTED will remain set until End Transfer completes.
Tested-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
There is a rare race condition that may happen during a Disconnect
Interrupt if we have a started request that happens to be
dequeued *after* completion of End Transfer command. If that happens,
that request will be left waiting for completion of an End Transfer
command that will never happen.
If End Transfer command has already completed before, we are safe to
giveback the request straight away.
Tested-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We have a proper flag for testing that we have a valid transfer in
flight, let's use that instead.
This patch is in preparation to fix a rare race condition that happens
upon Disconnect Interrupt.
Tested-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Move the Rohm Vendor ID to pci_ids.h instead of defining it in several
drivers.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
We must wait until End Transfer completes in order to clear
DWC3_EP_TRANSFER_STARTED, otherwise we may confuse the driver.
This patch is in preparation to fix a rare race condition that happens
upon Disconnect Interrupt.
Tested-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
When Sink negotiates PPS, the voltage range of selected PPS APDO might
not cover the previous voltage (out_volt). If the previous out_volt is
lower than the new min_volt, the output voltage in RDO might be set to
an invalid value. For instance, supposed that the previous voltage is
5V, and the new voltage range in the APDO is 7V-12V. Then the output
voltage in the RDO should not be set to 5V which is lower than the
possible min_volt 7V.
Fix this by choosing the maximal value between the previous voltage and
the new min_volt first. And ensure that this value will not exceed the
new max_volt. The new out_volt will fall within the new voltage range
while being the closest value compared to the previous out_volt.
Signed-off-by: Kyle Tso <kyletso@google.com>
Reviewed-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Fixes: c710d0bb76 ("usb: typec: tcpm: Extend the matching rules on PPS APDO selection")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dwc3 got a fix for cases when gadget driver queue an OUT request of
length 0; this is a case that has been overlooked for quite some time
now.
Exynos' dwc3 glue layer got a fix on the error path for those cases
where clk_prepare_enable() fails.
TI's AM335x PHY driver got a fix for a race condition during
probe. This race happened because driver was powering off the PHY only
after adding the PHY handle to the framework. The result is that we
could fall into a situation where user of the PHY (MUSB) could call
phy_init() before phy driver's probe() called phy_poweroff() which
would result in a powered off PHY after phy_init() was called.
The old net2272 driver got a fix for an erroneous use of bitwise
negation.
-----BEGIN PGP SIGNATURE-----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=xcVV
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v5.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v5.0-rc4
Dwc3 got a fix for cases when gadget driver queue an OUT request of
length 0; this is a case that has been overlooked for quite some time
now.
Exynos' dwc3 glue layer got a fix on the error path for those cases
where clk_prepare_enable() fails.
TI's AM335x PHY driver got a fix for a race condition during
probe. This race happened because driver was powering off the PHY only
after adding the PHY handle to the framework. The result is that we
could fall into a situation where user of the PHY (MUSB) could call
phy_init() before phy driver's probe() called phy_poweroff() which
would result in a powered off PHY after phy_init() was called.
The old net2272 driver got a fix for an erroneous use of bitwise
negation.
* tag 'fixes-for-v5.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb:
usb: phy: am335x: fix race condition in _probe
usb: dwc3: exynos: Fix error handling of clk_prepare_enable
usb: phy: fix link errors
usb: gadget: udc: net2272: Fix bitwise and boolean operations
usb: dwc3: gadget: Handle 0 xfer length for OUT EP
Handling short packets (length < max packet size) in the Inventra DMA
engine in the MUSB driver causes the MUSB DMA controller to hang. An
example of a problem that is caused by this problem is when streaming
video out of a UVC gadget, only the first video frame is transferred.
For short packets (mode-0 or mode-1 DMA), MUSB_TXCSR_TXPKTRDY must be
set manually by the driver. This was previously done in musb_g_tx
(musb_gadget.c), but incorrectly (all csr flags were cleared, and only
MUSB_TXCSR_MODE and MUSB_TXCSR_TXPKTRDY were set). Fixing that problem
allows some requests to be transferred correctly, but multiple requests
were often put together in one USB packet, and caused problems if the
packet size was not a multiple of 4. Instead, set MUSB_TXCSR_TXPKTRDY
in dma_controller_irq (musbhsdma.c), just like host mode transfers.
This topic was originally tackled by Nicolas Boichat [0] [1] and is
discussed further at [2] as part of his GSoC project [3].
[0] https://groups.google.com/forum/?hl=en#!topic/beagleboard-gsoc/k8Azwfp75CU
[1] b0be3b6cc1?p=beagleboard-usbsniffer:beagleboard-usbsniffer-kernel.git;a=patch;h=b0be3b6cc195ba732189b04f1d43ec843c3e54c9
[2] http://beagleboard-usbsniffer.blogspot.com/2010/07/musb-isochronous-transfers-fixed.html
[3] http://elinux.org/BeagleBoard/GSoC/USBSniffer
Fixes: 550a7375fe ("USB: Add MUSB and TUSB support")
Signed-off-by: Paul Elder <paul.elder@ideasonboard.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix vep_free_request() to return when usb_ep and usb_request are null
instead of calling WARN_ON.
Signed-off-by: Shuah Khan <shuah@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
No need to initialize the PHY from the driver's probe. It is done by
the core automatically and doing it twice would increment the
phy->powercount counter to 2 instead of 1. During later suspend
operation, the counter will be decremented to one, no phy->power_off()
will occur and worse than that, the following phy->power_on() at
resume time will also be skipped, failing the whole S2RAM operation.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The mvebu xHCI host driver does not have suspend/resume support. Use of
the XHCI_RESET_ON_RESUME quirk is mandatory in order to avoid failures
after resume. This will work only if no USB device is plugged-in.
While at it, mention in the Kconfig file that this IP is also present
on the A3700 SoC.
Signed-off-by: Ofer Heifetz <oferh@marvell.com>
[miquel.raynal@bootlin.com: Reword the commit message]
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Current implementation of the USB core does not take into account the
new PHY framework. Correct the situation by adding a call to
phy_set_mode() before phy_power_on().
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
power off the phy should be done before populate the phy. Otherwise,
am335x_init() could be called by the phy owner to power on the phy first,
then am335x_phy_probe() turns off the phy again without the caller knowing
it.
Fixes: 2fc711d763 ("usb: phy: am335x: Enable USB remote wakeup using PHY wakeup")
Cc: stable@vger.kernel.org # v3.18+
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
If clk_prepare_enable() fails in dwc3_exynos_probe() or in
dwc3_exynos_resume(), exynos->clks[0] is left undisabled
because of usage preincrement in while condition.
Found by Linux Driver Verification project (linuxtesting.org).
Fixes: 9f2168367a ("usb: dwc3: exynos: Rework clock handling and prepare for new variants")
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Fix link errors when CONFIG_FSL_USB2_OTG is enabled and USB_OTG_FSM is
set to module then the following link error occurs.
aarch64-linux-gnu-ld: drivers/usb/phy/phy-fsl-usb.o: in function `fsl_otg_ioctl':
drivers/usb/phy/phy-fsl-usb.c:1083: undefined reference to `otg_statemachine'
aarch64-linux-gnu-ld: drivers/usb/phy/phy-fsl-usb.c:1083:(.text+0x574): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `otg_statemachine'
aarch64-linux-gnu-ld: drivers/usb/phy/phy-fsl-usb.o: in function `fsl_otg_start_srp':
drivers/usb/phy/phy-fsl-usb.c:674: undefined reference to `otg_statemachine'
aarch64-linux-gnu-ld: drivers/usb/phy/phy-fsl-usb.c:674:(.text+0x61c): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `otg_statemachine'
aarch64-linux-gnu-ld: drivers/usb/phy/phy-fsl-usb.o: in function `fsl_otg_set_host':
drivers/usb/phy/phy-fsl-usb.c:593: undefined reference to `otg_statemachine'
aarch64-linux-gnu-ld: drivers/usb/phy/phy-fsl-usb.c:593:(.text+0x7a4): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `otg_statemachine'
aarch64-linux-gnu-ld: drivers/usb/phy/phy-fsl-usb.o: in function `fsl_otg_start_hnp':
drivers/usb/phy/phy-fsl-usb.c:695: undefined reference to `otg_statemachine'
aarch64-linux-gnu-ld: drivers/usb/phy/phy-fsl-usb.c:695:(.text+0x858): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `otg_statemachine'
aarch64-linux-gnu-ld: drivers/usb/phy/phy-fsl-usb.o: in function `a_wait_enum':
drivers/usb/phy/phy-fsl-usb.c:274: undefined reference to `otg_statemachine'
aarch64-linux-gnu-ld: drivers/usb/phy/phy-fsl-usb.c:274:(.text+0x16f0): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `otg_statemachine'
aarch64-linux-gnu-ld: drivers/usb/phy/phy-fsl-usb.o:drivers/usb/phy/phy-fsl-usb.c:619: more undefined references to `otg_statemachine' follow
aarch64-linux-gnu-ld: drivers/usb/phy/phy-fsl-usb.o: in function `fsl_otg_set_peripheral':
drivers/usb/phy/phy-fsl-usb.c:619:(.text+0x1fa0): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `otg_statemachine'
make[1]: *** [Makefile:1020: vmlinux] Error 1
make[1]: Target 'Image' not remade because of errors.
make: *** [Makefile:152: sub-make] Error 2
make: Target 'Image' not remade because of errors.
Rework so that FSL_USB2_OTG depends on that the USB_OTG_FSM is builtin.
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
(!x & y) strikes again.
Fix bitwise and boolean operations by enclosing the expression:
intcsr & (1 << NET2272_PCI_IRQ)
in parentheses, before applying the boolean operator '!'.
Notice that this code has been there since 2011. So, it would
be helpful if someone can double-check this.
This issue was detected with the help of Coccinelle.
Fixes: ceb80363b2 ("USB: net2272: driver for PLX NET2272 USB device controller")
Cc: stable@vger.kernel.org
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
For OUT endpoints, zero-length transfers require MaxPacketSize buffer as
per the DWC_usb3 programming guide 3.30a section 4.2.3.3.
This patch fixes this by explicitly checking zero length
transfer to correctly pad up to MaxPacketSize.
Fixes: c6267a5163 ("usb: dwc3: gadget: align transfers to wMaxPacketSize")
Cc: stable@vger.kernel.org
Signed-off-by: Tejas Joglekar <joglekar@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Now that we have req->status, we don't need this extra flag
anymore. It's safe to remove it.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Queueing the same request twice can introduce hard-to-debug
problems. At least one function driver - Android's f_mtp.c - is known
to cause this problem.
While that function is out-of-tree, this is a problem that's easy
enough to avoid.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch starts tracking dwc3_request status. A following patch will
build on top of this to prevent a request from being queued twice.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
RZ/G2E USB 3.0 implementation is like the one found on R-Car E3,
therefore add the same quirk.
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We only have uvcg_dbg, uvcg_info, and uvcg_err, so add uvcg_warn macro
to print gadget device name and function name along with format.
Signed-off-by: Paul Elder <paul.elder@ideasonboard.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Switch RX processing from tasklet to (delayed) work queue. This allows
receiver more room to process incoming data and prevents flood of
"ttyGS0: RX not scheduled?" messages on HS receive on slow CPU.
A side effect is 2.4MB/s zmodem transfer speed (up from 1.8MB/s)
on my test board.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Delete tab aligning a statement with the right hand side of a
preceding assignment rather than the left hand side.
Found with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The AM654 SoC contains a DWC3 controller with TI specific
wrapper. Add support for that.
Unlike the Keystone 2 case, for AM654 We don't need to
process any IRQs for basic USB operation.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
On v3.10a in dual-role mode, if port is in device mode
and gadget driver isn't loaded, the OTG event interrupts don't
come through.
It seems that if the core is configured to be OTG2.0 only,
then we can't leave the DCFG.DEVSPD at Super-speed (default)
if we expect OTG to work properly. It must be set to High-speed.
Fix this issue by configuring DCFG.DEVSPD to the supported
maximum speed at gadget init. Device tree still needs to provide
correct supported maximum speed for this to work.
This issue wasn't present on v2.40a but is seen on v3.10a.
It doesn't cause any side effects on v2.40a.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
According to Documentation/timers/timers-howto.txt, a driver should
use usleep_range() instead of udelay() on NON-ATOMIC CONTEXT if
"SLEEPING FOR ~USECS OR SMALL MSECS ( 10us - 20ms)".
Since the .hardware_init() and .power_ctrl() will run on NON-ATOMIC
CONTEXT, this patch replaces udelay() with usleep_range().
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add a MSM8998 specific DT compatible so that we can properly bind to the
device and enable the USB controller.
Reviewed-by: Andy Gross <andy.gross@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Jeffrey Hugo <jhugo@codeaurora.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
'num' is a u8 variable, it never greater than 255,
So the if branch is dead code and can be removed.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The QFN28 package version of the CP2102N has three additional gpio pins.
Add support for these.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Fixes the following coccinelle warning:
./drivers/usb/misc/ftdi-elan.c:972:10-12: WARNING: possible condition with no effect (if == else)
./drivers/usb/misc/ftdi-elan.c:983:9-11: WARNING: possible condition with no effect (if == else)
./drivers/usb/misc/ftdi-elan.c:2052:11-13: WARNING: possible condition with no effect (if == else)
All these else/if branches just do the same thing actually as the last else branch,
So it can be merged into the last branch.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove debugfs if tcpm register port fails.
Signed-off-by: Li Jun <jun.li@nxp.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB3503 chip can be used without any I2C connection, what is handled by
a simple platform device driver. Add support for resetting the chip (via
GPIO lines) during system suspend/resume cycle by adding calls to existing
suspend/resume functions used for E2C device.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove macros which are only wrappers around standard operations. When
we expand them into code, we see that sisusbcon_memsetw can simply use
memset16 and sisusbcon_putcs can just call memcpy. So make the code
compact.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After the previous patch we see, that whole files are ifdeffed depending
on CONFIG options. So do not build the files at all if the CONFIG is not
enabled. (I.e. move the check from .c to Makefile.)
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are two macros defined:
1) ifdef CONFIG_COMPAT => define SISUSB_NEW_CONFIG_COMPAT
2) ifdef CONFIG_USB_SISUSBVGA_CON => define INCL_SISUSB_CON
Remove the latter and make use only of the former. This removes one
layer of obfuscation.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert SISUSB_VADDR and SISUSB_HADDR to inline functions. Now, there
are no more hidden accesses to local variables (vc_data and
sisusb_usb_data).
sisusb_haddr returns unsigned long from now on, not u16 *, as ulong is
what every caller expects -- we can remove some casts.
Call sites were aligned to be readable too.
Use sisusb_haddr on 4 more places in sisusbcon_blank and
sisusbcon_scroll. It was open coded there with [x, y] being [0, 0].
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The variable 'empty_packets' does not used in any other places
except for self increment, so it can be removed.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB devices permanently connected to USB ports may be described in ACPI
tables and share ACPI devices with ports they are connected to. See [1]
for details.
This will allow us to describe sideband resources for devices, such as,
for example, hard reset line for BT USB controllers.
[1] https://docs.microsoft.com/en-us/windows-hardware/drivers/bringup/other-acpi-namespace-objects#acpi-namespace-hierarchy-and-adr-for-embedded-usb-devices
Signed-off-by: Dmitry Torokhov <dtor@chromium.org>
Signed-off-by: Rajat Jain <rajatja@google.com> (changed how we get the usb_port)
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tested-by: Sukumar Ghorai <sukumar.ghorai@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
We have been using Makefile for well over a decade now, use that name
instead of Kbuild.
Also, while moving the file, add the proper SPDX identifier at the top
of it.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This file is really really old, and doesn't make any sense to keep
around anymore, so just drop it.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are a few remaining drivers/usb/ files that do not have SPDX
identifiers in them, all of these are either Kconfig or Makefiles. Add
the correct GPL-2.0 identifier to them to make scanning tools happy.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
fixed the checkpatch.pl warning:
WARNING: Missing a blank line after declarations
Added space after declarations to conform to coding style.
Signed-off-by: Bharath Vedartham <linux.bhar@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here's a fix for the new ftdi gpio support, which failed to take
autosuspend into account, and a patch adding missing SPDX identifiers to
the keyspan headers.
Included are also some new device ids.
All but the SPDX patch have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCXEGnxAAKCRALxc3C7H1l
CDWIAP9c3kzZLIxhVLyBpLaBgLQftCov5n0oIfNvbrFak3NZIQEA1R2Lvd/b5wbQ
RS5ZaPzLIeeIUHA0YcavuMjdF3na5QM=
=J9iV
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-5.0-rc3' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for 5.0-rc3
Here's a fix for the new ftdi gpio support, which failed to take
autosuspend into account, and a patch adding missing SPDX identifiers to
the keyspan headers.
Included are also some new device ids.
All but the SPDX patch have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
* tag 'usb-serial-5.0-rc3' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: keyspan_usa: add proper SPDX lines for .h files
USB: serial: pl2303: add new PID to support PL2303TB
USB: serial: ftdi_sio: fix GPIO not working in autosuspend
USB: serial: simple: add Motorola Tetra TPG2200 device id
The keyspan_usa??msg.h files are under a BSD-3 style license, so
properly label them as such with a SPDX line at the top of the file.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
USB Bluetooth controller QCA ROME (0cf3:e007) sometimes stops working
after S3:
[ 165.110742] Bluetooth: hci0: using NVM file: qca/nvm_usb_00000302.bin
[ 168.432065] Bluetooth: hci0: Failed to send body at 4 of 1953 (-110)
After some experiments, I found that disabling LPM can workaround the
issue.
On some platforms, the USB power is cut during S3, so the driver uses
reset-resume to resume the device. During port resume, LPM gets enabled
twice, by usb_reset_and_verify_device() and usb_port_resume().
Consolidate all checks into new LPM helpers to make sure LPM only gets
enabled once.
Fixes: de68bab4fa ("usb: Don't enable USB 2.0 Link PM by default.”)
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: stable <stable@vger.kernel.org> # after much soaking
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use new helpers to make LPM enabling/disabling more clear.
This is a preparation to subsequent patch.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: stable <stable@vger.kernel.org> # after much soaking
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove USB errata checking code from driver. Applicability of erratum
is retrieved by reading corresponding property in device tree.
This property is written during device tree fixup.
Besides, replace spaces with tabs to make code aligned.
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@nxp.com>
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_USB_EHCI_FSL is not dependent on FSL_SOC, it can be built on
non-PPC platforms.
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
arm/arm64's io.h doesn't define clrbits32() and clrsetbits_be32(), which
causing compile failure on some Layerscape Platforms (such as LS1021A and
LS2012A which also integrates FSL EHCI controller). So use
ioread32be()/iowrite32be() instead to make it workable on both
powerpc and arm.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The HW can swap the USB differential-pair (D+/D-) for each port
separately. So the USB signals can be re-aligned with a misplaced
USB connector on the PCB.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Richard Leitner <richard.leitner@skidata.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to Documentation/timers/timers-howto.txt, a driver should
use usleep_range() instead of udelay() on NON-ATOMIC CONTEXT if
"SLEEPING FOR ~USECS OR SMALL MSECS ( 10us - 20ms)".
Since the .hardware_init() and .power_ctrl() will run on NON-ATOMIC
CONTEXT, this patch replaces udelay() with usleep_range().
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add this SFR compatible definition for the sam9x60 SoC and manage
its use in ohci-at91.c driver.
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
One of the more common cases of allocation size calculations is finding the
size of a structure that has a zero-sized array at the end, along with memory
for some number of elements for that array. For example:
struct foo {
int stuff;
void *entry[];
};
instance = kzalloc(sizeof(struct foo) + sizeof(void *) * count, GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can now
use the new struct_size() helper:
instance = kzalloc(struct_size(instance, entry, count), GFP_KERNEL);
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The hub sends hot-plug events to the host trough it's interrupt URB. The
driver takes care of completing the URB and re-submitting it. Completion
errors are handled in the hub_event() work, yet submission errors are
ignored, rendering the device unresponsive. All further events are lost.
It is fairly hard to find this issue in the wild, since you have to time
the USB hot-plug event with the URB submission failure. For instance it
could be the system running out of memory or some malfunction in the USB
controller driver. Nevertheless, it's pretty reasonable to think it'll
happen sometime. One can trigger this issue using eBPF's function
override feature (see BCC's inject.py script).
This patch adds a retry routine to the event of a submission error. The
HUB driver will try to re-submit the URB once every second until it's
successful or the HUB is disconnected.
As some USB subsystems already take care of this issue, the
implementation was inspired from usbhid/hid_core.c's.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Oliver Neukum <oneukum@suse.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The patch "usb: simplify usbport trigger" together with "leds: triggers:
add device attribute support" caused an regression for the usbport
trigger. it will no longer enumerate any active usb hub ports under the
"ports" directory in the sysfs class directory, if the usb host drivers
are fully initialized before the usbport trigger was loaded.
The reason is that the usbport driver tries to register the sysfs
entries during the activate() callback. And this will fail with -2 /
ENOENT because the patch "leds: triggers: add device attribute support"
made it so that the sysfs "ports" group was only being added after the
activate() callback succeeded.
This version of the patch reverts parts of the "usb: simplify usbport
trigger" patch and restores usbport trigger's functionality.
Fixes: 6f7b0bad88 ("usb: simplify usbport trigger")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During the static checker, "data->usbmisc_data" may be NULL.
Fix it by adding this pointer judgement before using.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The README file ni the drivers/usb/usbip/ directory is not needed
anymore, so just delete it.
Cc: Valentina Manea <valentina.manea.m@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Shuah Khan <shuah@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add new PID to support PL2303TB (TYPE_HX)
Signed-off-by: Charles Yeh <charlesyeh522@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
To clear GINTSTS2_WKUP_ALERT_INT bit in GINTSTS2 register
require to write 1. This bit is implemented as "Write to clear".
Fixes: 187c5298a1 ("usb: dwc2: gadget: Add handler for WkupAlert interrupt")
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
There is a bug in the current GPIO code for ftdi_sio: it failed to take USB
autosuspend into account. If the device is in autosuspend, calls to
usb_control_msg() fail with -EHOSTUNREACH. Because the standard value for
autosuspend timeout is usually 2-5 seconds, this made it almost impossible
to use the GPIOs on machines that have USB autosuspend enabled. This patch
fixes the issue by acquiring a PM lock on the device for the duration of
the USB transfers. Tested on an FT231X device.
Signed-off-by: Karoly Pados <pados@pados.hu>
[ johan: simplify code somewhat ]
Fixes: ba93cc7da8 ("USB: serial: ftdi_sio: implement GPIO support for FT-X devices")
Cc: stable <stable@vger.kernel.org> # 4.20
Signed-off-by: Johan Hovold <johan@kernel.org>
The source_sink_alloc_func() function is supposed to return error
pointers on error. The function is called from usb_get_function() which
doesn't check for NULL returns so it would result in an Oops.
Of course, in the current kernel, small allocations always succeed so
this doesn't affect runtime.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Currently the link_state is uninitialized and the default value is 0(U0)
before the first time we start the udc, and after we start the udc then
stop the udc, the link_state will be undefined.
We may have the following warnings if we start the udc again with
an undefined link_state:
WARNING: CPU: 0 PID: 327 at drivers/usb/dwc3/gadget.c:294 dwc3_send_gadget_ep_cmd+0x304/0x308
dwc3 100e0000.hidwc3_0: wakeup failed --> -22
[...]
Call Trace:
[<c010f270>] (unwind_backtrace) from [<c010b3d8>] (show_stack+0x10/0x14)
[<c010b3d8>] (show_stack) from [<c034a4dc>] (dump_stack+0x84/0x98)
[<c034a4dc>] (dump_stack) from [<c0118000>] (__warn+0xe8/0x100)
[<c0118000>] (__warn) from [<c0118050>](warn_slowpath_fmt+0x38/0x48)
[<c0118050>] (warn_slowpath_fmt) from [<c0442ec0>](dwc3_send_gadget_ep_cmd+0x304/0x308)
[<c0442ec0>] (dwc3_send_gadget_ep_cmd) from [<c0445e68>](dwc3_ep0_start_trans+0x48/0xf4)
[<c0445e68>] (dwc3_ep0_start_trans) from [<c0446750>](dwc3_ep0_out_start+0x64/0x80)
[<c0446750>] (dwc3_ep0_out_start) from [<c04451c0>](__dwc3_gadget_start+0x1e0/0x278)
[<c04451c0>] (__dwc3_gadget_start) from [<c04452e0>](dwc3_gadget_start+0x88/0x10c)
[<c04452e0>] (dwc3_gadget_start) from [<c045ee54>](udc_bind_to_driver+0x88/0xbc)
[<c045ee54>] (udc_bind_to_driver) from [<c045f29c>](usb_gadget_probe_driver+0xf8/0x140)
[<c045f29c>] (usb_gadget_probe_driver) from [<bf005424>](gadget_dev_desc_UDC_store+0xac/0xc4 [libcomposite])
[<bf005424>] (gadget_dev_desc_UDC_store [libcomposite]) from[<c023d8e0>] (configfs_write_file+0xd4/0x160)
[<c023d8e0>] (configfs_write_file) from [<c01d51e8>] (__vfs_write+0x1c/0x114)
[<c01d51e8>] (__vfs_write) from [<c01d5ff4>] (vfs_write+0xa4/0x168)
[<c01d5ff4>] (vfs_write) from [<c01d6d40>] (SyS_write+0x3c/0x90)
[<c01d6d40>] (SyS_write) from [<c0107400>] (ret_fast_syscall+0x0/0x3c)
Signed-off-by: Zeng Tao <prime.zeng@hisilicon.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
OUT endpoint requests may somtimes have this flag set when
preparing to be submitted to HW indicating that there is an
additional TRB chained to the request for alignment purposes.
If that request is removed before the controller can execute the
transfer (e.g. ep_dequeue/ep_disable), the request will not go
through the dwc3_gadget_ep_cleanup_completed_request() handler
and will not have its needs_extra_trb flag cleared when
dwc3_gadget_giveback() is called. This same request could be
later requeued for a new transfer that does not require an
extra TRB and if it is successfully completed, the cleanup
and TRB reclamation will incorrectly process the additional TRB
which belongs to the next request, and incorrectly advances the
TRB dequeue pointer, thereby messing up calculation of the next
requeust's actual/remaining count when it completes.
The right thing to do here is to ensure that the flag is cleared
before it is given back to the function driver. A good place
to do that is in dwc3_gadget_del_and_unmap_request().
Fixes: c6267a5163 ("usb: dwc3: gadget: align transfers to wMaxPacketSize")
Cc: stable@vger.kernel.org
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We see dwc3 endpoint stopped by unwanted irq during
suspend resume test, which is caused dwc3 ep can't be started
with error "No Resource".
Here, add synchronize_irq before suspend to sync the
pending IRQ handlers complete.
Signed-off-by: Bo He <bo.he@intel.com>
Signed-off-by: Yu Wang <yu.y.wang@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Here are some small USB driver fixes and quirk updates for 5.0-rc2.
The majority here are some quirks for some storage devices to get them
to work properly. There's also a fix here to resolve the reported
issues with some audio devices that say they are UAC3 compliant, but
really are not.
And a fix up for the MAINTAINERS file to remove a dead url.
All have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXDsQMA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykM2wCgzC1E5NUpoCqPZHaYQ/0LNLm6SaEAoIbebWBo
rl39FeUBmPJLTmKD0pFX
=4K55
-----END PGP SIGNATURE-----
Merge tag 'usb-5.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some small USB driver fixes and quirk updates for 5.0-rc2.
The majority here are some quirks for some storage devices to get them
to work properly. There's also a fix here to resolve the reported
issues with some audio devices that say they are UAC3 compliant, but
really are not.
And a fix up for the MAINTAINERS file to remove a dead url.
All have been in linux-next with no reported issues"
* tag 'usb-5.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: storage: Remove outdated URL from MAINTAINERS
USB: Add USB_QUIRK_DELAY_CTRL_MSG quirk for Corsair K70 RGB
usbcore: Select only first configuration for non-UAC3 compliant devices
USB: storage: add quirk for SMI SM3350
USB: storage: don't insert sane sense for SPC3+ when bad sense specified
usb: cdc-acm: send ZLP for Telit 3G Intel based modems
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
void *entry[];
};
instance = kmalloc(sizeof(struct foo) + sizeof(void *) * count, GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
instance = kmalloc(struct_size(instance, entry, count), GFP_KERNEL);
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We already need to zero out memory for dma_alloc_coherent(), as such
using dma_zalloc_coherent() is superflous. Phase it out.
This change was generated with the following Coccinelle SmPL patch:
@ replace_dma_zalloc_coherent @
expression dev, size, data, handle, flags;
@@
-dma_zalloc_coherent(dev, size, handle, flags)
+dma_alloc_coherent(dev, size, handle, flags)
Suggested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
[hch: re-ran the script on the latest tree]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Delete tab aligning a statement with the right hand side of a
preceding assignment rather than the left hand side.
Found with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The failure happened when I tried to send up to 96DPs per an interval
for SSP ISOC transations by libusb, this is used to verify SSP ISOC
function of USB3 GEN2 controller, so update it as 96DPs.
(refer usb3.1r1.0 section 8.12.6 Isochronous Transactions)
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are two statements that are indented incorrectly and need
to be moved to a new line. Fix these.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is better to initialize the return value "result" to -ENOMEM
than to 0. And because "result" takes the return value of
usb_parse_configuration() which returns 0 for success, setting
"result" to 0 at before and after of the for loop is unnecessary.
Signed-off-by: Suwan Kim <suwan.kim027@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To match the Corsair Strafe RGB, the Corsair K70 RGB also requires
USB_QUIRK_DELAY_CTRL_MSG to completely resolve boot connection issues
discussed here: https://github.com/ckb-next/ckb-next/issues/42.
Otherwise roughly 1 in 10 boots the keyboard will fail to be detected.
Patch that applied delay control quirk for Corsair Strafe RGB:
cb88a05887 ("usb: quirks: add control message delay for 1b1c:1b20")
Previous K70 RGB patch to add delay-init quirk:
7a1646d922 ("Add delay-init quirk for Corsair K70 RGB keyboards")
Signed-off-by: Jack Stocker <jackstocker.93@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In most of the UAC1 and UAC2 audio devices, the first
configuration is most often the best configuration.
However, with recent patch to support UAC3 configuration,
second configuration was unintentionally chosen for
some of the UAC1/2 devices that had more than one
configuration. This was because of the existing check
after the audio config check which selected any config
which had a non-vendor class. This patch fixes this issue.
Fixes: f13912d3f0 ("usbcore: Select UAC3 configuration for audio if present")
Reported-by: Con Kolivas <kernel@kolivas.org>
Signed-off-by: Saranya Gopal <saranya.gopal@intel.com>
Tested-by: Con Kolivas <kernel@kolivas.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SMI SM3350 USB-UFS bridge controller cannot handle long sense request
correctly and will make the chip refuse to do read/write when requested
long sense.
Add a bad sense quirk for it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Cc: stable <stable@vger.kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the code will set US_FL_SANE_SENSE flag unconditionally if
device claims SPC3+, however we should allow US_FL_BAD_SENSE flag to
prevent this behavior, because SMI SM3350 UFS-USB bridge controller,
which claims SPC4, will show strange behavior with 96-byte sense
(put the chip into a wrong state that cannot read/write anything).
Check the presence of US_FL_BAD_SENSE when assuming US_FL_SANE_SENSE on
SPC4+ devices.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Cc: stable <stable@vger.kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Telit 3G Intel based modems require zero packet to be sent if
out data size is equal to the endpoint max packet size.
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Nobody has actually used the type (VERIFY_READ vs VERIFY_WRITE) argument
of the user address range verification function since we got rid of the
old racy i386-only code to walk page tables by hand.
It existed because the original 80386 would not honor the write protect
bit when in kernel mode, so you had to do COW by hand before doing any
user access. But we haven't supported that in a long time, and these
days the 'type' argument is a purely historical artifact.
A discussion about extending 'user_access_begin()' to do the range
checking resulted this patch, because there is no way we're going to
move the old VERIFY_xyz interface to that model. And it's best done at
the end of the merge window when I've done most of my merges, so let's
just get this done once and for all.
This patch was mostly done with a sed-script, with manual fix-ups for
the cases that weren't of the trivial 'access_ok(VERIFY_xyz' form.
There were a couple of notable cases:
- csky still had the old "verify_area()" name as an alias.
- the iter_iov code had magical hardcoded knowledge of the actual
values of VERIFY_{READ,WRITE} (not that they mattered, since nothing
really used it)
- microblaze used the type argument for a debug printout
but other than those oddities this should be a total no-op patch.
I tried to fix up all architectures, did fairly extensive grepping for
access_ok() uses, and the changes are trivial, but I may have missed
something. Any missed conversion should be trivially fixable, though.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Including (in no particular order):
- Page table code for AMD IOMMU now supports large pages where
smaller page-sizes were mapped before. VFIO had to work around
that in the past and I included a patch to remove it (acked by
Alex Williamson)
- Patches to unmodularize a couple of IOMMU drivers that would
never work as modules anyway.
- Work to unify the the iommu-related pointers in
'struct device' into one pointer. This work is not finished
yet, but will probably be in the next cycle.
- NUMA aware allocation in iommu-dma code
- Support for r8a774a1 and r8a774c0 in the Renesas IOMMU driver
- Scalable mode support for the Intel VT-d driver
- PM runtime improvements for the ARM-SMMU driver
- Support for the QCOM-SMMUv2 IOMMU hardware from Qualcom
- Various smaller fixes and improvements
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=DT9A
-----END PGP SIGNATURE-----
Merge tag 'iommu-updates-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU updates from Joerg Roedel:
- Page table code for AMD IOMMU now supports large pages where smaller
page-sizes were mapped before. VFIO had to work around that in the
past and I included a patch to remove it (acked by Alex Williamson)
- Patches to unmodularize a couple of IOMMU drivers that would never
work as modules anyway.
- Work to unify the the iommu-related pointers in 'struct device' into
one pointer. This work is not finished yet, but will probably be in
the next cycle.
- NUMA aware allocation in iommu-dma code
- Support for r8a774a1 and r8a774c0 in the Renesas IOMMU driver
- Scalable mode support for the Intel VT-d driver
- PM runtime improvements for the ARM-SMMU driver
- Support for the QCOM-SMMUv2 IOMMU hardware from Qualcom
- Various smaller fixes and improvements
* tag 'iommu-updates-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (78 commits)
iommu: Check for iommu_ops == NULL in iommu_probe_device()
ACPI/IORT: Don't call iommu_ops->add_device directly
iommu/of: Don't call iommu_ops->add_device directly
iommu: Consolitate ->add/remove_device() calls
iommu/sysfs: Rename iommu_release_device()
dmaengine: sh: rcar-dmac: Use device_iommu_mapped()
xhci: Use device_iommu_mapped()
powerpc/iommu: Use device_iommu_mapped()
ACPI/IORT: Use device_iommu_mapped()
iommu/of: Use device_iommu_mapped()
driver core: Introduce device_iommu_mapped() function
iommu/tegra: Use helper functions to access dev->iommu_fwspec
iommu/qcom: Use helper functions to access dev->iommu_fwspec
iommu/of: Use helper functions to access dev->iommu_fwspec
iommu/mediatek: Use helper functions to access dev->iommu_fwspec
iommu/ipmmu-vmsa: Use helper functions to access dev->iommu_fwspec
iommu/dma: Use helper functions to access dev->iommu_fwspec
iommu/arm-smmu: Use helper functions to access dev->iommu_fwspec
ACPI/IORT: Use helper functions to access dev->iommu_fwspec
iommu: Introduce wrappers around dev->iommu_fwspec
...
Here is the big set of USB and PHY driver patches for 4.21-rc1.
All of the usual bits are in here:
- loads of USB gadget driver updates and additions
- new device ids
- phy driver updates
- xhci reworks and new features
- typec updates
Full details are in the shortlog.
All of these have been in linux-next for a long time with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXCYxNA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yl4pQCfaQBjMxPpp6TVcHANZ/O+zE3NH/wAoL11p3IB
KUq8v9pmcHO8sW5TWOJw
=iYGf
-----END PGP SIGNATURE-----
Merge tag 'usb-4.21-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/PHY updates from Greg KH:
"Here is the big set of USB and PHY driver patches for 4.21-rc1.
All of the usual bits are in here:
- loads of USB gadget driver updates and additions
- new device ids
- phy driver updates
- xhci reworks and new features
- typec updates
Full details are in the shortlog.
All of these have been in linux-next for a long time with no reported
issues"
* tag 'usb-4.21-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (142 commits)
USB: serial: option: add Fibocom NL678 series
cdc-acm: fix abnormal DATA RX issue for Mediatek Preloader.
usb: r8a66597: Fix a possible concurrency use-after-free bug in r8a66597_endpoint_disable()
usb: typec: tcpm: Extend the matching rules on PPS APDO selection
usb: typec: Improve Alt Mode documentation
usb: musb: dsps: fix runtime pm for peripheral mode
usb: musb: dsps: fix otg state machine
USB: serial: pl2303: add ids for Hewlett-Packard HP POS pole displays
usb: renesas_usbhs: add support for RZ/G2E
usb: ehci-omap: Fix deferred probe for phy handling
usb: roles: Add a description for the class to Kconfig
usb: renesas_usbhs: mark PM functions as __maybe_unused
usb: core: Remove unnecessary memset()
usb: host: isp1362-hcd: convert to DEFINE_SHOW_ATTRIBUTE
phy: qcom-qmp: Expose provided clocks to DT
dt-bindings: phy-qcom-qmp: Move #clock-cells to child
phy: qcom-qmp: Utilize fully-specified DT registers
dt-bindings: phy-qcom-qmp: Fix register underspecification
phy: ti: fix semicolon.cocci warnings
phy: dphy: Add configuration helpers
...
This is mostly update of the usual drivers: smarpqi, lpfc, qedi,
megaraid_sas, libsas, zfcp, mpt3sas, hisi_sas. Additionally, we have
a pile of annotation, unused variable and minor updates. The big API
change is the updates for Christoph's DMA rework which include
removing the DISABLE_CLUSTERING flag. And finally there are a couple
of target tree updates.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXCEUNiYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishdjKAP9vrTTv
qFaYmAoRSbPq9ZiixaXLMy0K/6o76Uay0gnBqgD/fgn3jg/KQ6alNaCjmfeV3wAj
u1j3H7tha9j1it+4pUw=
=GDa+
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly update of the usual drivers: smarpqi, lpfc, qedi,
megaraid_sas, libsas, zfcp, mpt3sas, hisi_sas.
Additionally, we have a pile of annotation, unused variable and minor
updates.
The big API change is the updates for Christoph's DMA rework which
include removing the DISABLE_CLUSTERING flag.
And finally there are a couple of target tree updates"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (259 commits)
scsi: isci: request: mark expected switch fall-through
scsi: isci: remote_node_context: mark expected switch fall-throughs
scsi: isci: remote_device: Mark expected switch fall-throughs
scsi: isci: phy: Mark expected switch fall-through
scsi: iscsi: Capture iscsi debug messages using tracepoints
scsi: myrb: Mark expected switch fall-throughs
scsi: megaraid: fix out-of-bound array accesses
scsi: mpt3sas: mpt3sas_scsih: Mark expected switch fall-through
scsi: fcoe: remove set but not used variable 'port'
scsi: smartpqi: call pqi_free_interrupts() in pqi_shutdown()
scsi: smartpqi: fix build warnings
scsi: smartpqi: update driver version
scsi: smartpqi: add ofa support
scsi: smartpqi: increase fw status register read timeout
scsi: smartpqi: bump driver version
scsi: smartpqi: add smp_utils support
scsi: smartpqi: correct lun reset issues
scsi: smartpqi: correct volume status
scsi: smartpqi: do not offline disks for transient did no connect conditions
scsi: smartpqi: allow for larger raid maps
...
Pull crypto updates from Herbert Xu:
"API:
- Add 1472-byte test to tcrypt for IPsec
- Reintroduced crypto stats interface with numerous changes
- Support incremental algorithm dumps
Algorithms:
- Add xchacha12/20
- Add nhpoly1305
- Add adiantum
- Add streebog hash
- Mark cts(cbc(aes)) as FIPS allowed
Drivers:
- Improve performance of arm64/chacha20
- Improve performance of x86/chacha20
- Add NEON-accelerated nhpoly1305
- Add SSE2 accelerated nhpoly1305
- Add AVX2 accelerated nhpoly1305
- Add support for 192/256-bit keys in gcmaes AVX
- Add SG support in gcmaes AVX
- ESN for inline IPsec tx in chcr
- Add support for CryptoCell 703 in ccree
- Add support for CryptoCell 713 in ccree
- Add SM4 support in ccree
- Add SM3 support in ccree
- Add support for chacha20 in caam/qi2
- Add support for chacha20 + poly1305 in caam/jr
- Add support for chacha20 + poly1305 in caam/qi2
- Add AEAD cipher support in cavium/nitrox"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (130 commits)
crypto: skcipher - remove remnants of internal IV generators
crypto: cavium/nitrox - Fix build with !CONFIG_DEBUG_FS
crypto: salsa20-generic - don't unnecessarily use atomic walk
crypto: skcipher - add might_sleep() to skcipher_walk_virt()
crypto: x86/chacha - avoid sleeping under kernel_fpu_begin()
crypto: cavium/nitrox - Added AEAD cipher support
crypto: mxc-scc - fix build warnings on ARM64
crypto: api - document missing stats member
crypto: user - remove unused dump functions
crypto: chelsio - Fix wrong error counter increments
crypto: chelsio - Reset counters on cxgb4 Detach
crypto: chelsio - Handle PCI shutdown event
crypto: chelsio - cleanup:send addr as value in function argument
crypto: chelsio - Use same value for both channel in single WR
crypto: chelsio - Swap location of AAD and IV sent in WR
crypto: chelsio - remove set but not used variable 'kctx_len'
crypto: ux500 - Use proper enum in hash_set_dma_transfer
crypto: ux500 - Use proper enum in cryp_set_dma_transfer
crypto: aesni - Add scatter/gather avx stubs, and use them in C
crypto: aesni - Introduce partial block macro
..
Pull networking updates from David Miller:
1) New ipset extensions for matching on destination MAC addresses, from
Stefano Brivio.
2) Add ipv4 ttl and tos, plus ipv6 flow label and hop limit offloads to
nfp driver. From Stefano Brivio.
3) Implement GRO for plain UDP sockets, from Paolo Abeni.
4) Lots of work from Michał Mirosław to eliminate the VLAN_TAG_PRESENT
bit so that we could support the entire vlan_tci value.
5) Rework the IPSEC policy lookups to better optimize more usecases,
from Florian Westphal.
6) Infrastructure changes eliminating direct manipulation of SKB lists
wherever possible, and to always use the appropriate SKB list
helpers. This work is still ongoing...
7) Lots of PHY driver and state machine improvements and
simplifications, from Heiner Kallweit.
8) Various TSO deferral refinements, from Eric Dumazet.
9) Add ntuple filter support to aquantia driver, from Dmitry Bogdanov.
10) Batch dropping of XDP packets in tuntap, from Jason Wang.
11) Lots of cleanups and improvements to the r8169 driver from Heiner
Kallweit, including support for ->xmit_more. This driver has been
getting some much needed love since he started working on it.
12) Lots of new forwarding selftests from Petr Machata.
13) Enable VXLAN learning in mlxsw driver, from Ido Schimmel.
14) Packed ring support for virtio, from Tiwei Bie.
15) Add new Aquantia AQtion USB driver, from Dmitry Bezrukov.
16) Add XDP support to dpaa2-eth driver, from Ioana Ciocoi Radulescu.
17) Implement coalescing on TCP backlog queue, from Eric Dumazet.
18) Implement carrier change in tun driver, from Nicolas Dichtel.
19) Support msg_zerocopy in UDP, from Willem de Bruijn.
20) Significantly improve garbage collection of neighbor objects when
the table has many PERMANENT entries, from David Ahern.
21) Remove egdev usage from nfp and mlx5, and remove the facility
completely from the tree as it no longer has any users. From Oz
Shlomo and others.
22) Add a NETDEV_PRE_CHANGEADDR so that drivers can veto the change and
therefore abort the operation before the commit phase (which is the
NETDEV_CHANGEADDR event). From Petr Machata.
23) Add indirect call wrappers to avoid retpoline overhead, and use them
in the GRO code paths. From Paolo Abeni.
24) Add support for netlink FDB get operations, from Roopa Prabhu.
25) Support bloom filter in mlxsw driver, from Nir Dotan.
26) Add SKB extension infrastructure. This consolidates the handling of
the auxiliary SKB data used by IPSEC and bridge netfilter, and is
designed to support the needs to MPTCP which could be integrated in
the future.
27) Lots of XDP TX optimizations in mlx5 from Tariq Toukan.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1845 commits)
net: dccp: fix kernel crash on module load
drivers/net: appletalk/cops: remove redundant if statement and mask
bnx2x: Fix NULL pointer dereference in bnx2x_del_all_vlans() on some hw
net/net_namespace: Check the return value of register_pernet_subsys()
net/netlink_compat: Fix a missing check of nla_parse_nested
ieee802154: lowpan_header_create check must check daddr
net/mlx4_core: drop useless LIST_HEAD
mlxsw: spectrum: drop useless LIST_HEAD
net/mlx5e: drop useless LIST_HEAD
iptunnel: Set tun_flags in the iptunnel_metadata_reply from src
net/mlx5e: fix semicolon.cocci warnings
staging: octeon: fix build failure with XFRM enabled
net: Revert recent Spectre-v1 patches.
can: af_can: Fix Spectre v1 vulnerability
packet: validate address length if non-zero
nfc: af_nfc: Fix Spectre v1 vulnerability
phonet: af_phonet: Fix Spectre v1 vulnerability
net: core: Fix Spectre v1 vulnerability
net: minor cleanup in skb_ext_add()
net: drop the unused helper skb_ext_get()
...
The USB Power Delivery discrete components now can be enumerated by
i2c-multi-instantiate driver via several resources under single ACPI
device node (ACPI ID is INT3515).
Touchscreen support is added for the Mediacom Flexbook Edge 11.
Mellanox driver got fixed due to updates in their firmware.
The power management stub driver for AtomISP v2 is fixed in order to support
Intel Baytrail SoCs where same quirk is needed for S0ix to work.
Special key handling has been fixed for Favorites hotkey on Thinkpad, and
Screen LOCK on ASUS.
Ideapad Yoga 2 13 has no HW rfkill switch, thus, driver has been updated
to support this.
Few cleanups related to debugfs have been made in Intel IPS and
Intel PMC drivers. Besides that Intel PMC has been extended
to show more detailed information about Latency Tolerance.
The following is an automated git shortlog grouped by driver:
ACPI / scan:
- Create platform device for INT3515 ACPI nodes
Add the VLV ISP PCI ID to atomisp2_pm:
- Add the VLV ISP PCI ID to atomisp2_pm
asus-nb-wmi:
- Drop mapping of 0x33 and 0x34 scan codes
- Map 0x35 to KEY_SCREENLOCK
asus-wmi:
- Tell the EC the OS will handle the display off hotkey
dell-laptop:
- Mark expected switch fall-throughs
Documentation/ABI:
- Add new attribute for mlxreg-io sysfs interfaces
Fix config space access for intel_atomisp2_pm:
- Fix config space access for intel_atomisp2_pm
i2c:
- acpi: Introduce i2c_acpi_get_i2c_resource() helper
- acpi: Use ACPI_FAILURE instead of !ACPI_SUCCESS
- acpi: Return error pointers from i2c_acpi_new_device()
i2c-multi-instantiate:
- Allow to have same slaves
- Introduce IOAPIC IRQ support
- Distinguish IRQ resource type
- Count I2cSerialBus() resources
- Get rid of obsolete conditional
- Defer probe when no adapter found
- Accept errors of i2c_acpi_new_device()
ideapad-laptop:
- Add Yoga 2 13 to no_hw_rfkill list
iio:
- inv_mpu6050: Use i2c_acpi_get_i2c_resource() helper
intel_cht_int33fe:
- Get rid of obsolete conditional
- Accept errors of i2c_acpi_new_device()
- Remove duplicate NULL check
intel_ips:
- Convert to use DEFINE_SHOW_ATTRIBUTE macro
- Remove never happen condition
- NULL check before some freeing functions is not needed
- remove unnecessary checks in ips_debugfs_init
intel_pmc_core:
- convert to DEFINE_SHOW_ATTRIBUTE
- Decode Snoop / Non Snoop LTR
- Fix LTR IGNORE Max offset
- Show Latency Tolerance info
intel_telemetry:
- convert to DEFINE_SHOW_ATTRIBUTE
mlx-platform:
- Convert to use SPDX identifier
- Allow mlxreg-io driver activation for new systems
- Fix LED configuration
- Fix tachometer registers
- Rename new systems product names
- Add definitions for new registers
thinkpad_acpi:
- Cleanup quirks macros
- Change the keymap for Favorites hotkey
touchscreen_dmi:
- Add info for the Mediacom Flexbook Edge 11
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEqaflIX74DDDzMJJtb7wzTHR8rCgFAlwRE+sACgkQb7wzTHR8
rCi7URAAgpfdsHUkj3PdFmp5o3LHCD0m5Z9A6yAJrXyhCDRRkAMaGYyRe4vg3qE1
GBA6MbMyOrtW/LqvaQAajeMmDINl1Mz/5OIVCIwJUPnKk8K7Yy93pH5vKecUPX8q
ihItKmJIPdaqxH2LXrx6sh3Ob3QrVrcpfpW6109WM8auYB+BiNOhxejBZ4jvMiRd
9dG657gx64Y6Ot5kjGKpdblFrA930sA5kAiMFiCcjNP9S7xLhgfyZiPMSP48gUWb
OiqoJMsomamF8qxZsZzfRblZpOlFahuW51D2vZgHb7N6fA0qW1c3twdSoivQfTHa
KA+OuMgJ52vI8JDgUKj55LB88Pn5iFtmDsNodgQ25cBLgBkzKJQU9MfoK8QafvlV
OTjmGL+ENK4VufDwMEgOMlXdihVewOrQ3kzOm7JQgIlOSWE7l9BSa2CK0vSM9Jha
nfjjc5LowJaWA+QUrmx29VrRGmSYfrGhquGV/3U+TPafc5blpiqWTGxIkhaNFhKx
0yk/vzggGsIlvnYU2+zaJW8LAhLcb4R6ATEZMurZQdZlQefs+5oAEPSvOZ5gYdLX
PWj3swTMkIp7FKjGm7532T83v5lJyO9cxSV/3aIqzkdWNqMoYDDuNU8wCzTTBv5m
EoKQO+H2WCnlm5bgWQ82gjVDKmS63eDlT4WgYxm60OZ1ONuAwIo=
=kYH6
-----END PGP SIGNATURE-----
Merge tag 'platform-drivers-x86-v4.21-1' of git://git.infradead.org/linux-platform-drivers-x86
Pull x86 platform driver updates from Andy Shevchenko:
- The USB Power Delivery discrete components now can be enumerated by
i2c-multi-instantiate driver via several resources under single ACPI
device node (ACPI ID is INT3515).
- Touchscreen support is added for the Mediacom Flexbook Edge 11.
- Mellanox driver got fixed due to updates in their firmware.
- The power management stub driver for AtomISP v2 is fixed in order to
support Intel Baytrail SoCs where same quirk is needed for S0ix to
work.
- Special key handling has been fixed for Favorites hotkey on Thinkpad,
and Screen LOCK on ASUS.
- Ideapad Yoga 2 13 has no HW rfkill switch, thus, driver has been
updated to support this.
- Few cleanups related to debugfs have been made in Intel IPS and Intel
PMC drivers. Besides that Intel PMC has been extended to show more
detailed information about Latency Tolerance
* tag 'platform-drivers-x86-v4.21-1' of git://git.infradead.org/linux-platform-drivers-x86: (41 commits)
platform/x86: mlx-platform: Convert to use SPDX identifier
Documentation/ABI: Add new attribute for mlxreg-io sysfs interfaces
platform/x86: mlx-platform: Allow mlxreg-io driver activation for new systems
platform/x86: mlx-platform: Fix LED configuration
platform/x86: mlx-platform: Fix tachometer registers
platform/x86: mlx-platform: Rename new systems product names
platform/x86: mlx-platform: Add definitions for new registers
platform/x86: intel_telemetry: convert to DEFINE_SHOW_ATTRIBUTE
platform/x86: intel_pmc_core: convert to DEFINE_SHOW_ATTRIBUTE
platform/x86: thinkpad_acpi: Cleanup quirks macros
platform/x86: touchscreen_dmi: Add info for the Mediacom Flexbook Edge 11
platform/x86: Fix config space access for intel_atomisp2_pm
platform/x86: Add the VLV ISP PCI ID to atomisp2_pm
platform/x86: intel_ips: Convert to use DEFINE_SHOW_ATTRIBUTE macro
platform/x86: intel_ips: Remove never happen condition
platform/x86: intel_ips: NULL check before some freeing functions is not needed
platform/x86: intel_ips: remove unnecessary checks in ips_debugfs_init
iio: inv_mpu6050: Use i2c_acpi_get_i2c_resource() helper
ACPI / scan: Create platform device for INT3515 ACPI nodes
platform/x86: i2c-multi-instantiate: Allow to have same slaves
...
Here are the USB-serial updates for 4.21-rc1, including:
- support for mos7840 3-port devices
- improved ftdi baud-rate divisor calculations
- support for a new class of f81534 devices
Included are also various clean ups and some new pl2303 device ids.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCXBva9AAKCRALxc3C7H1l
CP6XAQClpmmKj59AiAJK+hlWIbNpznPUUrkGHS7mFyuWkDrllQEAsK2IofNWbs9y
g0ot/v4UgUVZHySGl5yYoV4A0uKJdAQ=
=oyPx
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-4.21-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Johan writes:
USB-serial updates for 4.21-rc1
Here are the USB-serial updates for 4.21-rc1, including:
- support for mos7840 3-port devices
- improved ftdi baud-rate divisor calculations
- support for a new class of f81534 devices
Included are also various clean ups and some new pl2303 device ids.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
* tag 'usb-serial-4.21-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: pl2303: add ids for Hewlett-Packard HP POS pole displays
USB: serial: mos7840: remove set but not used variables 'number, serial'
USB: serial: mos7840: add a product ID for the new product
USB: serial: mos7840: clean up register handling
USB: serial: ftdi_sio: use rounding when calculating baud rate divisors
USB: serial: f81534: fix reading old/new IC config
USB: serial: mos7840: remove set but not used variables 'st, data1, iflag'
USB: serial: quatech2: remove set but not used variable 'port_priv'
Lots of conflicts, by happily all cases of overlapping
changes, parallel adds, things of that nature.
Thanks to Stephen Rothwell, Saeed Mahameed, and others
for their guidance in these resolutions.
Signed-off-by: David S. Miller <davem@davemloft.net>
Mediatek Preloader is a proprietary embedded boot loader for loading
Little Kernel and Linux into device DRAM.
This boot loader also handle firmware update. Mediatek Preloader will be
enumerated as a virtual COM port when the device is connected to Windows
or Linux OS via CDC-ACM class driver. When the USB enumeration has been
done, Mediatek Preloader will send out handshake command "READY" to PC
actively instead of waiting command from the download tool.
Since Linux 4.12, the commit "tty: reset termios state on device
registration" (93857edd98) causes Mediatek
Preloader receiving some abnoraml command like "READYXX" as it sent.
This will be recognized as an incorrect response. The behavior change
also causes the download handshake fail. This change only affects
subsequent connects if the reconnected device happens to get the same minor
number.
By disabling the ECHO termios flag could avoid this problem. However, it
cannot be done by user space configuration when download tool open
/dev/ttyACM0. This is because the device running Mediatek Preloader will
send handshake command "READY" immediately once the CDC-ACM driver is
ready.
This patch wants to fix above problem by introducing "DISABLE_ECHO"
property in driver_info. When Mediatek Preloader is connected, the
CDC-ACM driver could disable ECHO flag in termios to avoid the problem.
Signed-off-by: Macpaul Lin <macpaul.lin@mediatek.com>
Cc: stable@vger.kernel.org
Reviewed-by: Johan Hovold <johan@kernel.org>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function r8a66597_endpoint_disable() and r8a66597_urb_enqueue() may
be concurrently executed.
The two functions both access a possible shared variable "hep->hcpriv".
This shared variable is freed by r8a66597_endpoint_disable() via the
call path:
r8a66597_endpoint_disable
kfree(hep->hcpriv) (line 1995 in Linux-4.19)
This variable is read by r8a66597_urb_enqueue() via the call path:
r8a66597_urb_enqueue
spin_lock_irqsave(&r8a66597->lock)
init_pipe_info
enable_r8a66597_pipe
pipe = hep->hcpriv (line 802 in Linux-4.19)
The read operation is protected by a spinlock, but the free operation
is not protected by this spinlock, thus a concurrency use-after-free bug
may occur.
To fix this bug, the spin-lock and spin-unlock function calls in
r8a66597_endpoint_disable() are moved to protect the free operation.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Current matching rules ensure that the voltage range of selected Source
Capability is entirely within the range defined in one of the Sink
Capabilities. This is reasonable but not practical because Sink may not
support wide range of voltage when sinking power while Source could
advertise its capabilities in relatively wider range. For example, a
Source PDO advertising 3.3V-11V@3A (9V Prog of Fixed Nominal Voltage)
will not be selected if the Sink requires 5V-12V@3A PPS power. However,
the Sink could work well if the requested voltage range in RDOs is
5V-11V@3A.
Currently accepted:
|--------- source -----|
|----------- sink ---------------|
Currently not accepted:
|--------- source -----|
|----------- sink ---------------|
|--------- source -----|
|----------- sink ---------------|
|--------- source -----------------|
|------ sink -------|
To improve the usability, change the matching rules to what listed
below:
a. The Source PDO is selectable if any portion of the voltage range
overlaps one of the Sink PDO's voltage range.
b. The maximum operational voltage will be the lower one between the
selected Source PDO and the matching Sink PDO.
c. The maximum power will be the maximum operational voltage times the
maximum current defined in the selected Source PDO
d. Select the Source PDO with the highest maximum power
Signed-off-by: Kyle Tso <kyletso@google.com>
Acked-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The same effects can be achieved by setting the dma_boundary to
PAGE_SIZE - 1 and the max_segment_size to PAGE_SIZE, so shift those
settings into the drivers. Note that in many cases the setting might
be bogus, but this keeps the status quo.
[mkp: fix myrs and myrb]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Most SCSI drivers want to enable "clustering", that is merging of
segments so that they might span more than a single page. Remove the
ENABLE_CLUSTERING define, and require drivers to explicitly set
DISABLE_CLUSTERING to disable this feature.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A few drivers were not setting the use_clustering flag at all and thus
default to disable. Fix them up to explicitly set this field in
preparation for additional cleanups.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Since the runtime PM support was added in musb, dsps relies on the timer
calling otg_timer() to activate the usb subsystem. However the driver
doesn't enable the timer for peripheral port, then the peripheral port is
unable to be enumerated by a host if the other usb port is disabled or in
peripheral mode too.
So let's start the timer for peripheral port too.
Fixes: ea2f35c01d ("usb: musb: Fix sleeping function called from invalid context for hdrc glue")
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Due to lack of ID pin interrupt event on AM335x devices, the musb dsps
driver uses polling to detect usb device attach for dual-role port.
But in the case if a micro-A cable adapter is attached without a USB device
attached to the cable, the musb state machine gets stuck in a_wait_vrise
state waiting for the MUSB_CONNECT interrupt which won't happen due to the
usb device is not attached. The state is stuck in a_wait_vrise even after
the micro-A cable is detached, which could cause VBUS retention if then the
dual-role port is attached to a host port.
To fix the problem, make a_wait_vrise as a transient state, then move the
state to either a_wait_bcon for host port or a_idle state for dual-role
port, if no usb device is attached to the port.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add device ids to pl2303 for the HP POS pole displays:
LM920: 03f0:026b
TD620: 03f0:0956
LD960TA: 03f0:4439
LD220TA: 03f0:4349
LM940: 03f0:5039
Signed-off-by: Scott Chen <scott@labau.com.tw>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Move Synopsys HAPS platform device IDs to pci_ids.h so that both
drivers/pci/quirks.c and dwc3-haps driver can reference these IDs.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
As commented in the struct's definition there shouldn't be anything
underneath its 'priv[0]' member as it would break some macros.
The patch converts the broken_suspend into a bit-field and relocates it
next to to the rest of bit-fields.
Fixes: a7d57abcc8 ("xhci: workaround CSS timeout on AMD SNPS 3.0 xHC")
Reported-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
HS-USB found in RZ/G2E (a.k.a. r8a774c0) is very similar to the
one found in R-Car E3 (a.k.a. r8a77990), as it needs to release
the PLL reset by the UGCTRL register like R-Car E3, therefore add
r8a774c0 support in a similar fashion to what was done for the
r8a77990.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
PHY model is being used on omap5 platforms even if port mode
is not OMAP_EHCI_PORT_MODE_PHY. So don't guess if PHY is required
or not based on PHY mode.
If PHY is provided in device tree, it must be required. So, if
devm_usb_get_phy_by_phandle() gives us an error code other
than -ENODEV (no PHY) then error out.
This fixes USB Ethernet on omap5-uevm if PHY happens to
probe after EHCI thus causing a -EPROBE_DEFER.
Cc: Johan Hovold <johan@kernel.org>
Cc: Ladislav Michl <ladis@linux-mips.org>
Reported-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
That makes the USB role switch support option visible and
selectable for the user. The class driver is also moved to
drivers/usb/roles/ directory.
This will fix an issue that we have with the Intel USB role
switch driver on systems that don't have USB Type-C connectors:
Intel USB role switch driver depends on the USB role switch
class as it should, but since there was no way for the user
to enable the USB role switch class, there was also no way
to select that driver. USB Type-C drivers select the USB
role switch class which makes the Intel USB role switch
driver available and therefore hides the problem.
So in practice Intel USB role switch driver was depending on
USB Type-C drivers.
Fixes: f6fb9ec02b ("usb: roles: Add Intel xHCI USB role switch driver")
Cc: <stable@vger.kernel.org>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Add the HSIC support for imx
-----BEGIN PGP SIGNATURE-----
iQEwBAABCAAaBQJcF1bIExxwZXRlci5jaGVuQG54cC5jb20ACgkQSFkpgVDWcbv1
Xgf/RIlKRdLOiO0wCJWkmiHRIU/YE0V6QNwhMKCUK2PfAqLI3px/a/uOam7U8ysn
6TvrUYxy/V7yBDCw6bR8bbJeP5gFjZPEnqd4RV6YZzP7Zc6FJ/10cLMWWGfB61JV
xqcVzJGjZ/AuU00TDDEeKXnGB4w6iH47x0ywimxlHSEhSUGQEoogopgtlr8JfnWg
bVQ9wr1jkUmkDymVFaHzrYSWVIToejGOB2kNRmhGpxKIUq3Mv/X0Vux50+egNpDK
ikyVo5oIr1cU0nVlAl2lquoTf6F7gRo2GduY9stw2VR6VxUUvd2cj57bJlhiwqPe
3jRiXjWtZKsWEcSpMhaT8ks+Og==
=Q7/x
-----END PGP SIGNATURE-----
Merge tag 'usb-ci-v4.21-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb into usb-next
Peter writes:
- Improve the over-current handling for imx
- Add the HSIC support for imx
* tag 'usb-ci-v4.21-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb:
usb: chipidea: imx: allow to configure oc polarity on i.MX25
usb: chipidea: imx: Warn if oc polarity isn't specified
usb: chipidea: imx: support configuring for active low oc signal
doc: usb: ci-hdrc-usb2: Add pinctrl properties for HSIC pin groups
usb: chipidea: host: override ehci->hub_control
usb: chipidea: imx: add HSIC support
usb: chipidea: add flag for imx hsic implementation
Replace the dev->iommu_group check with a proper function
call that better reprensents its purpose.
Cc: Mathias Nyman <mathias.nyman@intel.com>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Here are some new modem device ids.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCXBPTKwAKCRALxc3C7H1l
CKtnAQCMMhEqKVlPbvWAxEvyx9/1tm7fOaj052HBuYSZL5W0LQEA9mh8A/0+HpBC
lXyfNs77XsOlNjbgctouMgECKv5QKwU=
=RBJX
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-4.20-rc7' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for 4.20-rc7
Here are some new modem device ids.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
* tag 'usb-serial-4.20-rc7' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: option: add Telit LN940 series
USB: serial: option: add Fibocom NL668 series
USB: serial: option: add Simcom SIM7500/SIM7600 (MBIM mode)
USB: serial: option: add GosunCn ZTE WeLink ME3630
USB: serial: option: add HP lt4132
The code to prevent a bus suspend if a USB3 port was still in link training
also reacted to USB2 port polling state.
This caused bus suspend to busyloop in some cases.
USB2 polling state is different from USB3, and should not prevent bus
suspend.
Limit the USB3 link training state check to USB3 root hub ports only.
The origial commit went to stable so this need to be applied there as well
Fixes: 2f31a67f01 ("usb: xhci: Prevent bus suspend if a port connect change or polling state is detected")
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A follow-up patch will add a notifier type NETDEV_PRE_CHANGEADDR, which
allows vetoing of MAC address changes. One prominent path to that
notification is through dev_set_mac_address(). Therefore give this
function an extack argument, so that it can be packed together with the
notification. Thus a textual reason for rejection (or a warning) can be
communicated back to the user.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without CONFIG_PM, we get a new build warning here:
drivers/usb/renesas_usbhs/common.c:860:12: error: 'usbhsc_resume' defined but not used [-Werror=unused-function]
static int usbhsc_resume(struct device *dev)
^~~~~~~~~~~~~
drivers/usb/renesas_usbhs/common.c:844:12: error: 'usbhsc_suspend' defined but not used [-Werror=unused-function]
static int usbhsc_suspend(struct device *dev)
^~~~~~~~~~~~~~
Fixes: d54d334e75 ("usb: renesas_usbhs: Use SIMPLE_DEV_PM_OPS macro")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
register_root_hub() calls memset() setting usb_dev->bus->devmap.
devicemap to 0 during hcd probe function (usb_hcd_pci_probe). But
in previous function which is also the procedure of usb_hcd_pci_probe(),
usb_bus_init() already initialized bus->devmap calling memset().
Furthermore, register_root_hub() is called only once in kernel.
So, calling memset() which resets usb_bus->devmap.devicemap in
register_root_hub() is redundant.
Signed-off-by: Suwan Kim <suwan.kim027@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use DEFINE_SHOW_ATTRIBUTE macro to simplify the code.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
So it looks like folks are interested in dwc3 again. Almost 64% of the
changes are in dwc3 this time around with some other bits in gadget
functions and dwc2.
There are two important parts here: a. removal of the waitqueue from
dwc3's dequeue implementation, which will guarantee that gadget
functions can dequeue from any context and; b. better method for
starting isochronous transfers to avoid, as much as possible, missed
isoc frames.
Apart from these, we have the usual set of non-critical fixes and new
features all over the place.
-----BEGIN PGP SIGNATURE-----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=n8VS
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
USB changes for v4.21
So it looks like folks are interested in dwc3 again. Almost 64% of the
changes are in dwc3 this time around with some other bits in gadget
functions and dwc2.
There are two important parts here: a. removal of the waitqueue from
dwc3's dequeue implementation, which will guarantee that gadget
functions can dequeue from any context and; b. better method for
starting isochronous transfers to avoid, as much as possible, missed
isoc frames.
Apart from these, we have the usual set of non-critical fixes and new
features all over the place.
* tag 'usb-for-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb: (56 commits)
usb: dwc2: Fix disable all EP's on disconnect
usb: dwc3: gadget: Disable CSP for stream OUT ep
usb: dwc2: disable power_down on Amlogic devices
Revert "usb: dwc3: pci: Use devm functions to get the phy GPIOs"
USB: gadget: udc: s3c2410_udc: convert to DEFINE_SHOW_ATTRIBUTE
usb: mtu3: fix dbginfo in qmu_tx_zlp_error_handler
usb: dwc3: trace: add missing break statement to make compiler happy
usb: dwc3: gadget: Report isoc transfer frame number
usb: gadget: Introduce frame_number to usb_request
usb: renesas_usbhs: Use SIMPLE_DEV_PM_OPS macro
usb: renesas_usbhs: Remove dummy runtime PM callbacks
usb: dwc2: host: use hrtimer for NAK retries
usb: mtu3: clear SOFTCONN when clear USB3_EN if work as HS mode
usb: mtu3: enable SETUPENDISR interrupt
usb: mtu3: fix the issue about SetFeature(U1/U2_Enable)
usb: mtu3: enable hardware remote wakeup from L1 automatically
usb: mtu3: remove QMU checksum
usb/mtu3: power down device ip at setup
usb: dwc2: Disable power down feature on Samsung SoCs
usb: dwc3: Correct the logic for checking TRB full in __dwc3_prepare_one_trb()
...
Disabling all EP's allow to reset EP's to initial state.
Introduced new function dwc2_hsotg_ep_disable_lock() which
before calling dwc2_hsotg_ep_disable() function acquire
hsotg->lock and release on exiting.
From dwc2_hsotg_ep_disable() function removed acquiring
hsotg->lock.
In dwc2_hsotg_core_init_disconnected() function when USB
reset interrupt asserted disabling all ep’s by
dwc2_hsotg_ep_disable() function.
This updates eliminating sparse imbalance warnings.
Reverted changes in dwc2_hostg_disconnect() function.
Introduced new function dwc2_hsotg_ep_disable_lock().
Changed dwc2_hsotg_ep_ops. Now disable point to
dwc2_hsotg_ep_disable_lock() function.
In functions dwc2_hsotg_udc_stop() and dwc2_hsotg_suspend()
dwc2_hsotg_ep_disable() function replaced by
dwc2_hsotg_ep_disable_lock() function.
In dwc2_hsotg_ep_disable() function removed acquiring
of hsotg->lock.
Fixes: dccf1bad4b ("usb: dwc2: Disable all EP's on disconnect")
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Up to now the polarity of the over current pin was hard coded to active
high. Use the already defined device tree properties to configure polarity
on i.MX25, too. In difference to i.MX6/7 use active high behavior if the
polarity is unspecified to keep compatibility to existing device trees.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
The polarity of the over current detection pin isn't configured on i.MX6/7
if it's unspecified in the device tree. So the actual configuration depends
on bootloader behavior which is bad.
So encourage users to fix their device tree by issuing a warning in this
case.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
The status quo on i.MX6 is that if "over-current-active-high" is
specified in the device tree this is configured as expected. If
the property is missing polarity isn't changed and so the
polarity is kept as setup by the bootloader. Reset default is
active high, so active low can only be used with help by the
bootloader. On i.MX7 it is similar, but there disabling of
over current detection has a similar inconsistency.
This patch introduces a new property that allows to explicitly
configure for active low over current detection and consistently
sets this up. In the absence of an explicit configuration the
bit is kept as is. On i.MX7 over current detection is used unless
disabled in the device tree.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
The chipidea controller has some special requirements during
suspend/resume, override common ehci->hub_control to implement
it.
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
To support imx HSIC, there are some special requirement:
- The HSIC pad is 1.2v, it may need to supply from external
- The data/strobe pin needs to be pulled down first, and after
host mode is initialized, the strobe pin needs to be pulled up
- During the USB suspend/resume, special setting is needed
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
NXP (Freecale) imx HSIC design has some special requirements, add
some flags at host code to handle them.
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
In stream mode, when fast-forwarding TRBs, the stream number
is not cleared causing the new stream to not get assigned. So
we don't want controller to carry on transfers when short packet
is received. So disable the CSP for stream capable endpoint.
This is based on the 3.30a Programming guide, where table 3-1
device descriptor structure field definitions says for CSP bit
If this bit is 0, the controller generates an XferComplete event
and remove the stream. So if we keep CSP as 1 then switching between
streams would not happen as in stream mode, when fast-forwarding
TRBs, the stream number is not cleared causing the new stream to not get
assigned.
Signed-off-by: Tejas Joglekar <joglekar@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/usb/serial/mos7840.c: In function 'mos7840_send_cmd_write_baud_rate':
drivers/usb/serial/mos7840.c:1584:16: warning:
variable 'number' set but not used [-Wunused-but-set-variable]
drivers/usb/serial/mos7840.c: In function 'mos7840_change_port_settings':
drivers/usb/serial/mos7840.c:1695:21: warning:
variable 'serial' set but not used [-Wunused-but-set-variable]
'number' never used since introduction in commit 3f5429746d ("USB: Moschip
7840 USB-Serial Driver")
'serial' not used since commit 5833041f1b ("USB: serial: remove unnecessary
reinitialisations of urb->dev")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Disable power_down by setting the parameter to
DWC2_POWER_DOWN_PARAM_NONE. This fixes a problem on various Amlogic
Meson SoCs where USB devices are only recognized when plugged in before
booting Linux. A hot-plugged USB device was not detected even though the
device got power (my USB thumb drive for example has an LED which lit
up).
A similar fix was implemented for Rockchip SoCs in commit c216765d3a
("usb: dwc2: disable power_down on rockchip devices"). That commit
suggests that a change in the dwc2 driver is the cause because the
default value for the "hibernate" parameter (which then got renamed to
"power_down" to support other modes) was changed in the v4.17 merge
window with:
commit 6d23ee9caa ("Merge tag 'usb-for-v4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-testing").
Cc: <stable@vger.kernel.org> # 4.19
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Suggested-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Refactoring, no functional changes.
But worth mentioning that checking for port link resume state is now behind
a additional port power check.
This is fine as ports can't be in resume state if port power bit is not
set.
xhci spec section 4.19.1.1.6 figure 34 shows that port power bit must be
set for all 'Enable' substates, including U0,U1,U2,U3 (suspended), Resume,
and RExit states.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move U0 link state handing to USB3 and USB2 specific functions
Note that
bus_state->resuming_ports:
bus_state->resume_done[]:
are only used for USB2, and don't need to cleared for USB3 ports
No functional changes
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Group the code where the wPortstatus and wPortChange bits
are set into one place.
No functional changes
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mostly refactoring, with the exception that USB_PORT_STAT_L1 link state
is reported if xhci port link is in U2 AND port is powered.
Previously we did not check if the port was powered, but according to
xhci spec 4.19.1.1.6 All the 'Enabled' states, including
USB_PORT_STAT_L1 (U2), U1, U0 and U3 must have Port power bit set.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that each root hub has their own bus_state strucure the
hcd_undex() used to get the correct bus_state strucure is
no longer needed.
No functional changes
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move the bus_state structure under struct usb_hub.
We need a bus_state strucure for each roothub to keep track of suspend
related info for each port.
Instead of keeping an array of two bus_state structures right under
struct xhci, it makes more sense move them to the xhci_hub structure.
No functional changes.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is introduced for the pre-0.96 xHC controllers, and the driver only
support HW LPM for 1.0 and later controllers.It's not actually used now
and is thought not to be used in the future any more, so just remove it.
Signed-off-by: Zeng Tao <prime.zeng@hisilicon.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 211f658b7b ("usb: dwc3: pci: Use devm functions to get
the phy GPIOs") changed the code to claim the PHY GPIOs permanently
for Intel Baytrail devices.
This causes issues when the actual PHY driver attempts to claim the
same GPIO descriptors. For example, tusb1210 now fails to probe with:
tusb1210: probe of dwc3.0.auto.ulpi failed with error -16 (EBUSY)
dwc3-pci needs to turn on the PHY once before dwc3 is loaded, but
usually the PHY driver will then hold the GPIOs to turn off the
PHY when requested (e.g. during suspend).
To fix the problem, this reverts the commit to restore the old
behavior to put the GPIOs immediately after usage.
Link: https://www.spinics.net/lists/linux-usb/msg174681.html
Cc: stable@vger.kernel.org
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Use DEFINE_SHOW_ATTRIBUTE macro to simplify the code.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/usb/mtu3/mtu3_qmu.c: In function 'qmu_tx_zlp_error_handler':
drivers/usb/mtu3/mtu3_qmu.c:385:22: warning:
variable 'req' set but not used [-Wunused-but-set-variable]
It seems dbginfo original intention is print 'req' other than 'mreq'
Acked-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The missed break statement in the outer switch makes the code fall through
always and thus always same value will be printed.
Besides that, compiler warns about missed fall through marker:
drivers/usb/dwc3/./trace.h: In function ‘trace_raw_output_dwc3_log_trb’:
drivers/usb/dwc3/./trace.h:246:4: warning: this statement may fall through [-Wimplicit-fallthrough=]
switch (pcm) {
^~~~~~
Add the missing break statement to work correctly without compilation
warnings.
Fixes: fa8d965d73 ("usb: dwc3: trace: pretty print high-bandwidth transfers too")
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Here's a fix for a reported USB-console regression in 4.18 which
revealed a long-standing bug in the console implementation.
The patch has been in linux-next over night with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCXAlOXAAKCRALxc3C7H1l
COC9AP4jozobKxNIgbmP6LAwz34Zv19qZyhi2hOzM0Less5o+QD+PLKS4yFPErNq
L6jm+cb1RE3rW9bjrbphoT7PvQoa3QM=
=QA9N
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-4.20-rc6' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fix for v4.20-rc6
Here's a fix for a reported USB-console regression in 4.18 which
revealed a long-standing bug in the console implementation.
The patch has been in linux-next over night with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
* tag 'usb-serial-4.20-rc6' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: console: fix reported terminal settings
Don't allow USB3 U1 or U2 if the latency to wake up from the U-state
reaches the service interval for a periodic endpoint.
This is according to xhci 1.1 specification section 4.23.5.2 extra note:
"Software shall ensure that a device is prevented from entering a U-state
where its worst case exit latency approaches the ESIT."
Allowing too long exit latencies for periodic endpoint confuses xHC
internal scheduling, and new devices may fail to enumerate with a
"Not enough bandwidth for new device state" error from the host.
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Occasionally AMD SNPS 3.0 xHC does not respond to
CSS when set, also it does not flag anything on SRE and HCE
to point the internal xHC errors on USBSTS register. This stalls
the entire system wide suspend and there is no point in stalling
just because of xHC CSS is not responding.
To work around this problem, if the xHC does not flag
anything on SRE and HCE, we can skip the CSS
timeout and allow the system to continue the suspend. Once the
system resume happens we can internally reset the controller
using XHCI_RESET_ON_RESUME quirk
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Sandeep Singh <Sandeep.Singh@amd.com>
cc: Nehal Shah <Nehal-bakulchandra.Shah@amd.com>
Cc: <stable@vger.kernel.org>
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When reading an extra descriptor, we need to properly check the minimum
and maximum size allowed, to prevent from invalid data being sent by a
device.
Reported-by: Hui Peng <benquike@gmail.com>
Reported-by: Mathias Payer <mathias.payer@nebelwelt.net>
Co-developed-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Hui Peng <benquike@gmail.com>
Signed-off-by: Mathias Payer <mathias.payer@nebelwelt.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USB-serial console implementation has never reported the actual
terminal settings used. Despite storing the corresponding cflags in its
struct console, these were never honoured on later tty open() where the
tty termios would be left initialised to the driver defaults.
Unlike the serial console implementation, the USB-serial code calls
subdriver open() already at console setup. While calling set_termios()
and write() before open() looks like it could work for some USB-serial
drivers, others definitely do not expect this, so modelling this after
serial core is going to be intrusive, if at all possible.
Instead, use a (renamed) tty helper to save the termios data used at
console setup so that the tty termios reflects the actual terminal
settings after a subsequent tty open().
Note that the calls to tty_init_termios() (tty_driver_install()) and
tty_save_termios() are serialised using the disconnect mutex.
This specifically fixes a regression that was triggered by a recent
change adding software flow control to the pl2303 driver: a getty trying
to disable flow control while leaving the baud rate unchanged would now
also set the baud rate to the driver default (prior to the flow-control
change this had been a noop).
Fixes: 7041d9c3f0 ("USB: serial: pl2303: add support for tx xon/xoff flow control")
Cc: stable <stable@vger.kernel.org> # 4.18
Cc: Florian Zumbiehl <florz@florz.de>
Reported-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The spinlock was inside the urb completion function which is only
called once per display and is then resubmitted from this function.
There was no other place where this lock was used.
Signed-off-by: Alexander Theissen <alex.theissen@me.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver does allocate a DMA address with usb_alloc_coherent but did
not set the appropriate flag to signal that transfer_dma is set to a
valid value.
Signed-off-by: Alexander Theissen <alex.theissen@me.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some lower volume SanDisk Ultra Flair in 16GB, which the VID:PID is
in 0781:5591, will aggressively request LPM of U1/U2 during runtime,
when using this thumb drive as the OS installation key we found the
device will generate failure during U1 exit path making it dropped
from the USB bus, this causes a corrupted installation in system at
the end.
i.e.,
[ 166.918296] hub 2-0:1.0: state 7 ports 7 chg 0000 evt 0004
[ 166.918327] usb usb2-port2: link state change
[ 166.918337] usb usb2-port2: do warm reset
[ 166.970039] usb usb2-port2: not warm reset yet, waiting 50ms
[ 167.022040] usb usb2-port2: not warm reset yet, waiting 200ms
[ 167.276043] usb usb2-port2: status 02c0, change 0041, 5.0 Gb/s
[ 167.276050] usb 2-2: USB disconnect, device number 2
[ 167.276058] usb 2-2: unregistering device
[ 167.276060] usb 2-2: unregistering interface 2-2:1.0
[ 167.276170] xhci_hcd 0000:00:15.0: shutdown urb ffffa3c7cc695cc0 ep1in-bulk
[ 167.284055] sd 0:0:0:0: [sda] tag#0 FAILED Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK
[ 167.284064] sd 0:0:0:0: [sda] tag#0 CDB: Read(10) 28 00 00 33 04 90 00 01 00 00
...
Analyzed the USB trace in the link layer we realized it is because
of the 6-ms timer of tRecoveryConfigurationTimeout which documented
on the USB 3.2 Revision 1.0, the section 7.5.10.4.2 of "Exit from
Recovery.Configuration"; device initiates U1 exit -> Recovery.Active
-> Recovery.Configuration, then the host timer timeout makes the link
transits to eSS.Inactive -> Rx.Detect follows by a Warm Reset.
Interestingly, the other higher volume of SanDisk Ultra Flair sharing
the same VID:PID, such as 64GB, would not request LPM during runtime,
it sticks at U0 always, thus disabling LPM does not affect those thumb
drives at all.
The same odd occures in SanDisk Ultra Fit 16GB, VID:PID in 0781:5583.
Signed-off-by: Harry Pan <harry.pan@intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Syzbot and KASAN found the following invalid-free bug in
port_over_current_notify():
--------------------------------------------------------------------------
BUG: KASAN: double-free or invalid-free in port_over_current_notify
drivers/usb/core/hub.c:5192 [inline]
BUG: KASAN: double-free or invalid-free in port_event
drivers/usb/core/hub.c:5241 [inline]
BUG: KASAN: double-free or invalid-free in hub_event+0xd97/0x4140
drivers/usb/core/hub.c:5384
CPU: 1 PID: 32710 Comm: kworker/1:3 Not tainted 4.20.0-rc3+ #129
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS
Google 01/01/2011
Workqueue: usb_hub_wq hub_event
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x244/0x39d lib/dump_stack.c:113
print_address_description.cold.7+0x9/0x1ff mm/kasan/report.c:256
kasan_report_invalid_free+0x64/0xa0 mm/kasan/report.c:336
__kasan_slab_free+0x13a/0x150 mm/kasan/kasan.c:501
kasan_slab_free+0xe/0x10 mm/kasan/kasan.c:528
__cache_free mm/slab.c:3498 [inline]
kfree+0xcf/0x230 mm/slab.c:3817
port_over_current_notify drivers/usb/core/hub.c:5192 [inline]
port_event drivers/usb/core/hub.c:5241 [inline]
hub_event+0xd97/0x4140 drivers/usb/core/hub.c:5384
process_one_work+0xc90/0x1c40 kernel/workqueue.c:2153
worker_thread+0x17f/0x1390 kernel/workqueue.c:2296
kthread+0x35a/0x440 kernel/kthread.c:246
ret_from_fork+0x3a/0x50 arch/x86/entry/entry_64.S:352
--------------------------------------------------------------------------
The problem is caused by use of a static array to store
environment-string pointers. When the routine is called by multiple
threads concurrently, the pointers from one thread can overwrite those
from another.
The solution is to use an ordinary automatic array instead of a static
array.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: syzbot+98881958e1410ec7e53c@syzkaller.appspotmail.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add another Apple Cinema Display to the list of supported displays.
Signed-off-by: Alexander Theissen <alex.theissen@me.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since we are going to use the same in Designware USB 3 driver,
rename the property to be consistent across the drivers.
No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Implement the new frame_number API to report the isochronous interval
frame number. This patch checks and reports the interval in which the
isoc transfer was transmitted or received via the Isoc-First TRB SOF
number field.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
When the controller supports SS mode, but works as HS mode, the
SOFTCONN will not be cleared automatically when clear USB3_EN
by default, this cause an issue that can't disconnect from host,
so clear SOFTCONN when clear USB3_EN when the class driver want
to disable the D+ pullup.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the controller receives a new SETUP during SETUP data stage,
and will generate SETUPENDISR interrupt, the driver should abort
the current SETUP command and process the new one.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the issue: device doesn't accept LGO_U1/U2:
1. set SW_U1/U2_ACCEPT_ENABLE to eanble controller to accept LGO_U1/U2
by default;
2. enable/disable controller to initiate requests for transition into
U1/U2 by SW_U1/U2_REQUEST_ENABLE instead of SW_U1/U2_ACCEPT_ENABLE;
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enable hardware remote wakeup from L1 automatically based on the FIFO
status, instead of manual way.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The QMU checksum calculation is redundant, mostly used by debug,
so remove it here.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Originally, when dr_mode is USB_DR_MODE_HOST, it didn't power down device ip,
so host ip sleep will fail at ssusb_host_disable.
Power down device ip at ssusb_host_setup.
Signed-off-by: Hsin-Yi, Wang <hsinyi@chromium.org>
Acked-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mans Rullgard