Inline a part of ipv6_fixup_options() to avoid extra overhead on
function call if opt is NULL.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
udpv6_sendmsg() doesn't need dst after calling ip6_make_skb(), so
instead of taking an additional reference inside ip6_setup_cork()
and releasing the initial one afterwards, we can hand over a reference
into ip6_make_skb() saving two atomics. The only other user of
ip6_setup_cork() is ip6_append_data() and it requires an extra
dst_hold().
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
udpv6_sendmsg() first initialises an on-stack 88B struct flowi6 and then
copies it into cork, which is expensive. Avoid the copy in corkless case
by initialising on-stack cork->fl directly.
The main part is a couple of lines under !corkreq check. The rest
converts fl6 variable to be a pointer.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Another preparation patch. inet_cork_full already contains a field for
iflow, so we can avoid passing a separate struct iflow6 into
__ip6_append_data() and ip6_make_skb(), and use the flow stored in
inet_cork_full. Make sure callers set cork->fl, i.e. we init it in
ip6_append_data() and before calling ip6_make_skb().
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Convert a struct inet_cork argument in __ip6_append_data() to struct
inet_cork_full. As one struct contains another inet_cork is still can
be accessed via ->base field. It's a preparation patch making further
changes a bit cleaner.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
It doesn't appear there is any reason for ip6_cork_release() to zero
cork->fl, it'll be fully filled on next initialisation. This 88 bytes
memset accounts to 0.3-0.5% of total CPU cycles.
It's also needed in following patches and allows to remove an extar flow
copy in udp_v6_push_pending_frames().
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Clean up ip6_setup_cork() and ip6_cork_release() adding a local variable
for v6_cork->opt. It's a preparation patch for further changes.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
ipv6_push_nfrag_opts() doesn't change passed daddr, and so
__ip6_make_skb() doesn't actually need to keep an on-stack copy of
fl6->daddr. Set initially final_dst to fl6->daddr,
ipv6_push_nfrag_opts() will override it if needed, and get rid of extra
copies.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Corked AF_INET for ipv6 socket doesn't appear to be the hottest case,
so move it out of the common path under up->pending check to remove
overhead.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
__ip6_make_skb() gets a cork->dst ref, hands it over to skb and shortly
after puts cork->dst. Save two atomics by stealing it without extra
referencing, ip6_cork_release() handles NULL cork->dst.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This reverts commit b75326c201.
This commit breaks Linux compatibility with USGv6 tests. The RFC this
commit was based on is actually an expired draft: no published RFC
currently allows the new behaviour it introduced.
Without full IETF endorsement, the flash renumbering scenario this
patch was supposed to enable is never going to work, as other IPv6
equipements on the same LAN will keep the 2 hours limit.
Fixes: b75326c201 ("ipv6: Honor all IPv6 PIO Valid Lifetime values")
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPv6 GRO considers packets to belong to different flows when their
hop_limit is different. This seems counter-intuitive, the flow is
the same. hop_limit may vary because of various bugs or hacks but
that doesn't mean it's okay for GRO to reorder packets.
Practical impact of this problem on overall TCP performance
is unclear, but TCP itself detects this reordering and bumps
TCPSACKReorder resulting in user complaints.
Eric warns that there may be performance regressions in setups
which do packet spraying across links with similar RTT but different
hop count. To be safe let's target -next and not treat this
as a fix. If the packet spraying is using flow label there should
be no difference in behavior as flow label is checked first.
Note that the code plays an easy to miss trick by upcasting next_hdr
to a u16 pointer and compares next_hdr and hop_limit in one go.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Back in linux-2.6.25 (commit 98c6d1b261 "[NETNS]: Make icmpv6_sk per namespace.",
we added private per-cpu/per-netns ipv6 icmp sockets.
This adds memory and cpu costs, which do not seem needed.
Now typical servers have 256 or more cores, this adds considerable
tax to netns users.
icmp sockets are used from BH context, are not receiving packets,
and do not store any persistent state but the 'struct net' pointer.
icmpv6_xmit_lock() already makes sure to lock the chosen per-cpu
socket.
This patch has a considerable impact on the number of netns
that the worker thread in cleanup_net() can dismantle per second,
because ip6mr_sk_done() is no longer called, meaning we no longer
acquire the rtnl mutex, competing with other threads adding new netns.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prior patches in the series made sure tw_timer_handler()
can be fired after netns has been dismantled/freed.
We no longer have to scan a potentially big TCP ehash
table at netns dismantle.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since IPv4 routes support IPv6 gateways now, we can route IPv4 traffic in
NBMA tunnels.
Signed-off-by: Qing Deng <i@moy.cat>
Signed-off-by: David S. Miller <davem@davemloft.net>
The warning messages can be invoked from the data path for every packet
transmitted through an ip6gre netdev, leading to high CPU utilization.
Fix that by rate limiting the messages.
Fixes: 09c6bbf090 ("[IPV6]: Do mandatory IPv6 tunnel endpoint checks in realtime")
Reported-by: Maksym Yaremchuk <maksymy@nvidia.com>
Tested-by: Maksym Yaremchuk <maksymy@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While experimenting with FOU encapsulation Amir noticed that encapsulated IPv6
traffic fails to be delivered, if the peer IP address is configured locally.
It can be easily verified by creating a sit interface like below:
$ sudo ip link add name fou_test type sit remote 127.0.0.1 encap fou encap-sport auto encap-dport 1111
$ sudo ip link set fou_test up
and sending some IPv4 and IPv6 traffic to it
$ ping -I fou_test -c 1 1.1.1.1
$ ping6 -I fou_test -c 1 fe80::d0b0:dfff:fe4c:fcbc
"tcpdump -i any udp dst port 1111" will confirm that only the first IPv4 ping
was encapsulated and attempted to be delivered.
This seems like a limitation: for example, in a cloud environment the "peer"
service may be arbitrarily scheduled on any server within the cluster, where all
nodes are trying to send encapsulated traffic. And the unlucky node will not be
able to. Moreover, delivering encapsulated IPv4 traffic locally is allowed.
But I may not have all the context about this restriction and this code predates
the observable git history.
Reported-by: Amir Razmjou <arazmjou@cloudflare.com>
Signed-off-by: Ignat Korchagin <ignat@cloudflare.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20220107123842.211335-1-ignat@cloudflare.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following patchset contains Netfilter updates for net-next. This
includes one patch to update ovs and act_ct to use nf_ct_put() instead
of nf_conntrack_put().
1) Add netns_tracker to nfnetlink_log and masquerade, from Eric Dumazet.
2) Remove redundant rcu read-size lock in nf_tables packet path.
3) Replace BUG() by WARN_ON_ONCE() in nft_payload.
4) Consolidate rule verdict tracing.
5) Replace WARN_ON() by WARN_ON_ONCE() in nf_tables core.
6) Make counter support built-in in nf_tables.
7) Add new field to conntrack object to identify locally generated
traffic, from Florian Westphal.
8) Prevent NAT from shadowing well-known ports, from Florian Westphal.
9) Merge nf_flow_table_{ipv4,ipv6} into nf_flow_table_inet, also from
Florian.
10) Remove redundant pointer in nft_pipapo AVX2 support, from Colin Ian King.
11) Replace opencoded max() in conntrack, from Jiapeng Chong.
12) Update conntrack to use refcount_t API, from Florian Westphal.
13) Move ip_ct_attach indirection into the nf_ct_hook structure.
14) Constify several pointer object in the netfilter codebase,
from Florian Westphal.
15) Tree-wide replacement of nf_conntrack_put() by nf_ct_put(), also
from Florian.
16) Fix egress splat due to incorrect rcu notation, from Florian.
17) Move stateful fields of connlimit, last, quota, numgen and limit
out of the expression data area.
18) Build a blob to represent the ruleset in nf_tables, this is a
requirement of the new register tracking infrastructure.
19) Add NFT_REG32_NUM to define the maximum number of 32-bit registers.
20) Add register tracking infrastructure to skip redundant
store-to-register operations, this includes support for payload,
meta and bitwise expresssions.
* git://git.kernel.org/pub/scm/linux/kernel/git/pablo/nf-next: (32 commits)
netfilter: nft_meta: cancel register tracking after meta update
netfilter: nft_payload: cancel register tracking after payload update
netfilter: nft_bitwise: track register operations
netfilter: nft_meta: track register operations
netfilter: nft_payload: track register operations
netfilter: nf_tables: add register tracking infrastructure
netfilter: nf_tables: add NFT_REG32_NUM
netfilter: nf_tables: add rule blob layout
netfilter: nft_limit: move stateful fields out of expression data
netfilter: nft_limit: rename stateful structure
netfilter: nft_numgen: move stateful fields out of expression data
netfilter: nft_quota: move stateful fields out of expression data
netfilter: nft_last: move stateful fields out of expression data
netfilter: nft_connlimit: move stateful fields out of expression data
netfilter: egress: avoid a lockdep splat
net: prefer nf_ct_put instead of nf_conntrack_put
netfilter: conntrack: avoid useless indirection during conntrack destruction
netfilter: make function op structures const
netfilter: core: move ip_ct_attach indirection to struct nf_ct_hook
netfilter: conntrack: convert to refcount_t api
...
====================
Link: https://lore.kernel.org/r/20220109231640.104123-1-pablo@netfilter.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Alexei Starovoitov says:
====================
pull-request: bpf-next 2022-01-06
We've added 41 non-merge commits during the last 2 day(s) which contain
a total of 36 files changed, 1214 insertions(+), 368 deletions(-).
The main changes are:
1) Various fixes in the verifier, from Kris and Daniel.
2) Fixes in sockmap, from John.
3) bpf_getsockopt fix, from Kuniyuki.
4) INET_POST_BIND fix, from Menglong.
5) arm64 JIT fix for bpf pseudo funcs, from Hou.
6) BPF ISA doc improvements, from Christoph.
* https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next: (41 commits)
bpf: selftests: Add bind retry for post_bind{4, 6}
bpf: selftests: Use C99 initializers in test_sock.c
net: bpf: Handle return value of BPF_CGROUP_RUN_PROG_INET{4,6}_POST_BIND()
bpf/selftests: Test bpf_d_path on rdonly_mem.
libbpf: Add documentation for bpf_map batch operations
selftests/bpf: Don't rely on preserving volatile in PT_REGS macros in loop3
xdp: Add xdp_do_redirect_frame() for pre-computed xdp_frames
xdp: Move conversion to xdp_frame out of map functions
page_pool: Store the XDP mem id
page_pool: Add callback to init pages when they are allocated
xdp: Allow registering memory model without rxq reference
samples/bpf: xdpsock: Add timestamp for Tx-only operation
samples/bpf: xdpsock: Add time-out for cleaning Tx
samples/bpf: xdpsock: Add sched policy and priority support
samples/bpf: xdpsock: Add cyclic TX operation capability
samples/bpf: xdpsock: Add clockid selection support
samples/bpf: xdpsock: Add Dest and Src MAC setting for Tx-only operation
samples/bpf: xdpsock: Add VLAN support for Tx-only operation
libbpf 1.0: Deprecate bpf_object__find_map_by_offset() API
libbpf 1.0: Deprecate bpf_map__is_offload_neutral()
...
====================
Link: https://lore.kernel.org/r/20220107013626.53943-1-alexei.starovoitov@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The return value of BPF_CGROUP_RUN_PROG_INET{4,6}_POST_BIND() in
__inet_bind() is not handled properly. While the return value
is non-zero, it will set inet_saddr and inet_rcv_saddr to 0 and
exit:
err = BPF_CGROUP_RUN_PROG_INET4_POST_BIND(sk);
if (err) {
inet->inet_saddr = inet->inet_rcv_saddr = 0;
goto out_release_sock;
}
Let's take UDP for example and see what will happen. For UDP
socket, it will be added to 'udp_prot.h.udp_table->hash' and
'udp_prot.h.udp_table->hash2' after the sk->sk_prot->get_port()
called success. If 'inet->inet_rcv_saddr' is specified here,
then 'sk' will be in the 'hslot2' of 'hash2' that it don't belong
to (because inet_saddr is changed to 0), and UDP packet received
will not be passed to this sock. If 'inet->inet_rcv_saddr' is not
specified here, the sock will work fine, as it can receive packet
properly, which is wired, as the 'bind()' is already failed.
To undo the get_port() operation, introduce the 'put_port' field
for 'struct proto'. For TCP proto, it is inet_put_port(); For UDP
proto, it is udp_lib_unhash(); For icmp proto, it is
ping_unhash().
Therefore, after sys_bind() fail caused by
BPF_CGROUP_RUN_PROG_INET4_POST_BIND(), it will be unbinded, which
means that it can try to be binded to another port.
Signed-off-by: Menglong Dong <imagedong@tencent.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20220106132022.3470772-2-imagedong@tencent.com
Steffen Klassert says:
====================
pull request (net): ipsec 2022-01-06
1) Fix xfrm policy lookups for ipv6 gre packets by initializing
fl6_gre_key properly. From Ghalem Boudour.
2) Fix the dflt policy check on forwarding when there is no
policy configured. The check was done for the wrong direction.
From Nicolas Dichtel.
3) Use the correct 'struct xfrm_user_offload' when calculating
netlink message lenghts in xfrm_sa_len(). From Eric Dumazet.
4) Tread inserting xfrm interface id 0 as an error.
From Antony Antony.
5) Fail if xfrm state or policy is inserted with XFRMA_IF_ID 0,
xfrm interfaces with id 0 are not allowed.
From Antony Antony.
6) Fix inner_ipproto setting in the sec_path for tunnel mode.
From Raed Salem.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
pull request (net-next): ipsec-next 2022-01-06
1) Fix some clang_analyzer warnings about never read variables.
From luo penghao.
2) Check for pols[0] only once in xfrm_expand_policies().
From Jean Sacren.
3) The SA curlft.use_time was updated only on SA cration time.
Update whenever the SA is used. From Antony Antony
4) Add support for SM3 secure hash.
From Xu Jia.
5) Add support for SM4 symmetric cipher algorithm.
From Xu Jia.
6) Add a rate limit for SA mapping change messages.
From Antony Antony.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When finding the socket to report an error on, if the invoking packet
is using Segment Routing, the IPv6 destination address is that of an
intermediate router, not the end destination. Extract the ultimate
destination address from the segment address.
This change allows traceroute to function in the presence of Segment
Routing.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: David Ahern <dsahern@kernel.org>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RFC8754 says:
ICMP error packets generated within the SR domain are sent to source
nodes within the SR domain. The invoking packet in the ICMP error
message may contain an SRH. Since the destination address of a packet
with an SRH changes as each segment is processed, it may not be the
destination used by the socket or application that generated the
invoking packet.
For the source of an invoking packet to process the ICMP error
message, the ultimate destination address of the IPv6 header may be
required. The following logic is used to determine the destination
address for use by protocol-error handlers.
* Walk all extension headers of the invoking IPv6 packet to the
routing extension header preceding the upper-layer header.
- If routing header is type 4 Segment Routing Header (SRH)
o The SID at Segment List[0] may be used as the destination
address of the invoking packet.
Mangle the skb so the network header points to the invoking packet
inside the ICMP packet. The seg6 helpers can then be used on the skb
to find any segment routing headers. If found, mark this fact in the
IPv6 control block of the skb, and store the offset into the packet of
the SRH. Then restore the skb back to its old state.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: David Ahern <dsahern@kernel.org>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An ICMP error message can contain in its message body part of an IPv6
packet which invoked the error. Such a packet might contain a segment
router header. Export get_srh() so the ICMP code can make use of it.
Since his changes the scope of the function from local to global, add
the seg6_ prefix to keep the namespace clean. And move it into seg6.c
so it is always available, not just when IPV6_SEG6_LWTUNNEL is
enabled.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: David Ahern <dsahern@kernel.org>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As Nicolas noted, if gateway validation fails walking the multipath
attribute the code should jump to the cleanup to free previously
allocated memory.
Fixes: 1ff15a710a ("ipv6: Check attribute length for RTA_GATEWAY when deleting multipath route")
Signed-off-by: David Ahern <dsahern@kernel.org>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Link: https://lore.kernel.org/r/20220103170555.94638-1-dsahern@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
ip6_route_multipath_del loop continues processing the multipath
attribute even if delete of a nexthop path fails. For consistency,
do the same if the gateway attribute is invalid.
Fixes: 1ff15a710a ("ipv6: Check attribute length for RTA_GATEWAY when deleting multipath route")
Signed-off-by: David Ahern <dsahern@kernel.org>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Link: https://lore.kernel.org/r/20220103171911.94739-1-dsahern@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
v3:
- Report 'backlog' (bytes) instead of 'qlen' (number of packets)
v2:
- Fix sparse warning (use rcu_dereference)
This patch adds support for the queue depth in IOAM trace data fields.
The draft [1] says the following:
The "queue depth" field is a 4-octet unsigned integer field. This
field indicates the current length of the egress interface queue of
the interface from where the packet is forwarded out. The queue
depth is expressed as the current amount of memory buffers used by
the queue (a packet could consume one or more memory buffers,
depending on its size).
An existing function (i.e., qdisc_qstats_qlen_backlog) is used to
retrieve the current queue length without reinventing the wheel.
Note: it was tested and qlen is increasing when an artificial delay is
added on the egress with tc.
[1] https://datatracker.ietf.org/doc/html/draft-ietf-ippm-ioam-data#section-5.4.2.7
Signed-off-by: Justin Iurman <justin.iurman@uliege.be>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexei Starovoitov says:
====================
pull-request: bpf-next 2021-12-30
The following pull-request contains BPF updates for your *net-next* tree.
We've added 72 non-merge commits during the last 20 day(s) which contain
a total of 223 files changed, 3510 insertions(+), 1591 deletions(-).
The main changes are:
1) Automatic setrlimit in libbpf when bpf is memcg's in the kernel, from Andrii.
2) Beautify and de-verbose verifier logs, from Christy.
3) Composable verifier types, from Hao.
4) bpf_strncmp helper, from Hou.
5) bpf.h header dependency cleanup, from Jakub.
6) get_func_[arg|ret|arg_cnt] helpers, from Jiri.
7) Sleepable local storage, from KP.
8) Extend kfunc with PTR_TO_CTX, PTR_TO_MEM argument support, from Kumar.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
lwtunnel_valid_encap_type_attr is used to validate encap attributes
within a multipath route. Add length validation checking to the type.
lwtunnel_valid_encap_type_attr is called converting attributes to
fib{6,}_config struct which means it is used before fib_get_nhs,
ip6_route_multipath_add, and ip6_route_multipath_del - other
locations that use rtnh_ok and then nla_get_u16 on RTA_ENCAP_TYPE
attribute.
Fixes: 9ed59592e3 ("lwtunnel: fix autoload of lwt modules")
Signed-off-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure RTA_GATEWAY for IPv6 multipath route has enough bytes to hold
an IPv6 address.
Fixes: 6b9ea5a64e ("ipv6: fix multipath route replace error recovery")
Signed-off-by: David Ahern <dsahern@kernel.org>
Cc: Roopa Prabhu <roopa@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit referenced in the Fixes tag used nla_memcpy for RTA_GATEWAY as
does the current nla_get_in6_addr. nla_memcpy protects against accessing
memory greater than what is in the attribute, but there is no check
requiring the attribute to have an IPv6 address. Add it.
Fixes: 51ebd31815 ("ipv6: add support of equal cost multipath (ECMP)")
Signed-off-by: David Ahern <dsahern@kernel.org>
Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/mellanox/mlx5/core/en_tc.c
commit 077cdda764 ("net/mlx5e: TC, Fix memory leak with rules with internal port")
commit 31108d142f ("net/mlx5: Fix some error handling paths in 'mlx5e_tc_add_fdb_flow()'")
commit 4390c6edc0 ("net/mlx5: Fix some error handling paths in 'mlx5e_tc_add_fdb_flow()'")
https://lore.kernel.org/all/20211229065352.30178-1-saeed@kernel.org/
net/smc/smc_wr.c
commit 49dc9013e3 ("net/smc: Use the bitmap API when applicable")
commit 349d43127d ("net/smc: fix kernel panic caused by race of smc_sock")
bitmap_zero()/memset() is removed by the fix
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add a check that the user-provided option is at least as long as the
number of bytes we intend to read. Before this patch we would blindly
read sizeof(int) bytes even in cases where the user passed
optlen<sizeof(int), which would potentially read garbage or fault.
Discovered by new tests in https://github.com/google/gvisor/pull/6957 .
The original get_user call predates history in the git repo.
Signed-off-by: Tamir Duberstein <tamird@gmail.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Link: https://lore.kernel.org/r/20211229200947.2862255-1-willemdebruijn.kernel@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
sock.h is pretty heavily used (5k objects rebuilt on x86 after
it's touched). We can drop the include of filter.h from it and
add a forward declaration of struct sk_filter instead.
This decreases the number of rebuilt objects when bpf.h
is touched from ~5k to ~1k.
There's a lot of missing includes this was masking. Primarily
in networking tho, this time.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Acked-by: Stefano Garzarella <sgarzare@redhat.com>
Link: https://lore.kernel.org/bpf/20211229004913.513372-1-kuba@kernel.org
The "__ip6_tnl_parm" struct was left uninitialized causing an invalid
load of random data when the "__ip6_tnl_parm" struct was used elsewhere.
As an example, in the function "ip6_tnl_xmit_ctl()", it tries to access
the "collect_md" member. With "__ip6_tnl_parm" being uninitialized and
containing random data, the UBSAN detected that "collect_md" held a
non-boolean value.
The UBSAN issue is as follows:
===============================================================
UBSAN: invalid-load in net/ipv6/ip6_tunnel.c:1025:14
load of value 30 is not a valid value for type '_Bool'
CPU: 1 PID: 228 Comm: kworker/1:3 Not tainted 5.16.0-rc4+ #8
Hardware name: Red Hat KVM, BIOS 0.5.1 01/01/2011
Workqueue: ipv6_addrconf addrconf_dad_work
Call Trace:
<TASK>
dump_stack_lvl+0x44/0x57
ubsan_epilogue+0x5/0x40
__ubsan_handle_load_invalid_value+0x66/0x70
? __cpuhp_setup_state+0x1d3/0x210
ip6_tnl_xmit_ctl.cold.52+0x2c/0x6f [ip6_tunnel]
vti6_tnl_xmit+0x79c/0x1e96 [ip6_vti]
? lock_is_held_type+0xd9/0x130
? vti6_rcv+0x100/0x100 [ip6_vti]
? lock_is_held_type+0xd9/0x130
? rcu_read_lock_bh_held+0xc0/0xc0
? lock_acquired+0x262/0xb10
dev_hard_start_xmit+0x1e6/0x820
__dev_queue_xmit+0x2079/0x3340
? mark_lock.part.52+0xf7/0x1050
? netdev_core_pick_tx+0x290/0x290
? kvm_clock_read+0x14/0x30
? kvm_sched_clock_read+0x5/0x10
? sched_clock_cpu+0x15/0x200
? find_held_lock+0x3a/0x1c0
? lock_release+0x42f/0xc90
? lock_downgrade+0x6b0/0x6b0
? mark_held_locks+0xb7/0x120
? neigh_connected_output+0x31f/0x470
? lockdep_hardirqs_on+0x79/0x100
? neigh_connected_output+0x31f/0x470
? ip6_finish_output2+0x9b0/0x1d90
? rcu_read_lock_bh_held+0x62/0xc0
? ip6_finish_output2+0x9b0/0x1d90
ip6_finish_output2+0x9b0/0x1d90
? ip6_append_data+0x330/0x330
? ip6_mtu+0x166/0x370
? __ip6_finish_output+0x1ad/0xfb0
? nf_hook_slow+0xa6/0x170
ip6_output+0x1fb/0x710
? nf_hook.constprop.32+0x317/0x430
? ip6_finish_output+0x180/0x180
? __ip6_finish_output+0xfb0/0xfb0
? lock_is_held_type+0xd9/0x130
ndisc_send_skb+0xb33/0x1590
? __sk_mem_raise_allocated+0x11cf/0x1560
? dst_output+0x4a0/0x4a0
? ndisc_send_rs+0x432/0x610
addrconf_dad_completed+0x30c/0xbb0
? addrconf_rs_timer+0x650/0x650
? addrconf_dad_work+0x73c/0x10e0
addrconf_dad_work+0x73c/0x10e0
? addrconf_dad_completed+0xbb0/0xbb0
? rcu_read_lock_sched_held+0xaf/0xe0
? rcu_read_lock_bh_held+0xc0/0xc0
process_one_work+0x97b/0x1740
? pwq_dec_nr_in_flight+0x270/0x270
worker_thread+0x87/0xbf0
? process_one_work+0x1740/0x1740
kthread+0x3ac/0x490
? set_kthread_struct+0x100/0x100
ret_from_fork+0x22/0x30
</TASK>
===============================================================
The solution is to initialize "__ip6_tnl_parm" struct to zeros in the
"vti6_siocdevprivate()" function.
Signed-off-by: William Zhao <wizhao@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The max number of UDP gso segments is intended to cap to
UDP_MAX_SEGMENTS, this is checked in udp_send_skb().
skb->len contains network and transport header len here, we should use
only data len instead.
This is the ipv6 counterpart to the below referenced commit,
which missed the ipv6 change
Fixes: 158390e456 ("udp: using datalen to cap max gso segments")
Signed-off-by: Coco Li <lixiaoyan@google.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://lore.kernel.org/r/20211223222441.2975883-1-lixiaoyan@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We're about to break the cgroup-defs.h -> bpf-cgroup.h dependency,
make sure those who actually need more than the definition of
struct cgroup_bpf include bpf-cgroup.h explicitly.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Tejun Heo <tj@kernel.org>
Link: https://lore.kernel.org/bpf/20211216025538.1649516-3-kuba@kernel.org
The attributes are identical in all implementations so move the ipv4 one
into the core and remove the per-family nla policies.
Signed-off-by: Florian Westphal <fw@strlen.de>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pavel Begunkov