Add support for R-Car V3U (R8A779A0) SoC power areas and register
access, because register specification differs from R-Car Gen2/3.
Inspired by patches in the BSP by Tho Vu.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/1599810232-29035-5-git-send-email-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
APR client incorrectly prints out "ret" variable on pdr_add_lookup failure,
it should be printing the error value returned by the lookup instead.
Fixes: 8347356626 ("soc: qcom: apr: Add avs/audio tracking functionality")
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Link: https://lore.kernel.org/r/20200915154232.27523-1-sibis@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The array type of get_domain_list_resp is incorrectly marked as NO_ARRAY.
Due to which the following error was observed when using pdr helpers with
the downstream proprietary pd-mapper. Fix this up by marking it as
VAR_LEN_ARRAY instead.
Err logs:
qmi_decode_struct_elem: Fault in decoding: dl(2), db(27), tl(160), i(1), el(1)
failed to decode incoming message
PDR: tms/servreg get domain list txn wait failed: -14
PDR: service lookup for tms/servreg failed: -14
Tested-by: Rishabh Bhatnagar <rishabhb@codeaurora.org>
Fixes: fbe639b44a ("soc: qcom: Introduce Protection Domain Restart helpers")
Reported-by: Rishabh Bhatnagar <rishabhb@codeaurora.org>
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Link: https://lore.kernel.org/r/20200914145807.1224-1-sibis@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
please pull the following:
- Alvaro adds support for the BCM63xx (DSL) SoCs power domain controller
and adds support for the 6318, 6328, 6362, 63268.
- Florian adds support for tuning the Bus Interface Unit on 72164 and
72165, enables the Brahma-B53 and Cortex-A72 read-ahead cache for the
64-bit capable ARCH_BRCMSTB platforms, and finally updates the GISB
driver to support breakpoint notifications.
-----BEGIN PGP SIGNATURE-----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=njcZ
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-5.10/drivers' of https://github.com/Broadcom/stblinux into arm/drivers
This pull request contains Broadcom SoCs drivers changes for 5.10,
please pull the following:
- Alvaro adds support for the BCM63xx (DSL) SoCs power domain controller
and adds support for the 6318, 6328, 6362, 63268.
- Florian adds support for tuning the Bus Interface Unit on 72164 and
72165, enables the Brahma-B53 and Cortex-A72 read-ahead cache for the
64-bit capable ARCH_BRCMSTB platforms, and finally updates the GISB
driver to support breakpoint notifications.
* tag 'arm-soc/for-5.10/drivers' of https://github.com/Broadcom/stblinux:
bus: brcmstb_gisb: Add support for breakpoint interrupts
dt-bindings: bus: Document breakpoint interrupt for gisb-arb
soc: bcm: brcmstb: biuctrl: Change RAC data line prefetching after 4 consecutive lines
soc: bcm: brcmstb: biuctrl: Change RAC prefetch distance from +/-1 to +/- 2
soc: bcm: brcmstb: biuctrl: Tune MCP settings for 72165
soc: bcm: brcmstb: biuctrl: Tune MCP settings for 72164
MIPS: BMIPS: dts: add BCM63268 power domain support
MIPS: BMIPS: dts: add BCM6362 power domain support
MIPS: BMIPS: dts: add BCM6328 power domain support
soc: bcm: add BCM63xx power domain driver
MIPS: BMIPS: add BCM6318 power domain definitions
MIPS: BMIPS: add BCM63268 power domain definitions
MIPS: BMIPS: add BCM6362 power domain definitions
MIPS: BMIPS: add BCM6328 power domain definitions
dt-bindings: soc: brcm: add BCM63xx power domain binding
soc: bcm: brcmstb: biuctrl: Enable Read-ahead cache
bus: brcmstb_gisb: Shorten prints
Link: https://lore.kernel.org/r/20200912032153.1216354-3-f.fainelli@gmail.com
Signed-off-by: Olof Johansson <olof@lixom.net>
We now drop legacy platform data for RTC on am3, am4 and dra7.
And we add initial genpd support for PRM (Power and Reset Manager)
and use it to drop legacy platform data for am3 sgx and omap4/5
l4_abe interconnect instance.
-----BEGIN PGP SIGNATURE-----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=w5Zl
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.10/ti-sysc-drop-pdata-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/soc
Add initial genpd support for omaps to drop more platform data
We now drop legacy platform data for RTC on am3, am4 and dra7.
And we add initial genpd support for PRM (Power and Reset Manager)
and use it to drop legacy platform data for am3 sgx and omap4/5
l4_abe interconnect instance.
* tag 'omap-for-v5.10/ti-sysc-drop-pdata-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Drop legacy platform data for dra7 rtcss
ARM: OMAP2+: Drop legacy platform data for am3 and am4 rtc
soc: ti: pm33xx: Simplify RTC usage to prepare to drop platform data
ARM: dts: Configure omap4 and 5 l4_abe for genpd and drop platform data
ARM: dts: Configure am3 and am4 sgx for genpd and drop platform data
soc: ti: omap-prm: Configure omap4 and 5 l4_abe power domain
soc: ti: omap-prm: Configure sgx power domain for am3 and am4
soc: ti: omap-prm: Add basic power domain support
dt-bindings: omap: Update PRM binding for genpd
Link: https://lore.kernel.org/r/pull-1599132307-761202@atomide.com-2
Signed-off-by: Olof Johansson <olof@lixom.net>
- Drop a static qualifier in integrator_soc_init()
- Remove Integrator and Versatile from PHYS_OFFSET
-----BEGIN PGP SIGNATURE-----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=xtzo
-----END PGP SIGNATURE-----
Merge tag 'versatile-soc-v5.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator into arm/soc
Versatile SoC updates for the v5.10 kernel cycle:
- Drop a static qualifier in integrator_soc_init()
- Remove Integrator and Versatile from PHYS_OFFSET
* tag 'versatile-soc-v5.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator:
ARM: versatile: Remove Integrator and Realview from PHYS_OFFSET
soc: integrator: Drop pointless static qualifier in integrator_soc_init()
Link: https://lore.kernel.org/r/CACRpkdYYDSg8FAjJAqew5yEu7H1Y3E1rPN9TL25K31T=QWATuA@mail.gmail.com
Signed-off-by: Olof Johansson <olof@lixom.net>
Big cleanup for the Samsung S3C24xx and S3C64xx platforms, although it
also touches files shared with S5Pv210 and Exynos. This is mostly Arnd
Bergmann work which Krzysztof Kozlowski took over, rebased and polished.
The goal is to cleanup, merge and finally make the Samsung S3C24xx and
S3C64xx architectures multiplatform. The multiplatform did not happen
yet here - just cleaning up and merging into one arch/arm/mach-s3c
directory. However this is step forward for multiplatform or at least
to keep this code still maintainable.
This pulls also branch with changes for Samsung SoC sound drivers from
broonie/sound because the cleanups there were part of this series and
all further patches depend on them.
-----BEGIN PGP SIGNATURE-----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=bjMI
-----END PGP SIGNATURE-----
Merge tag 'samsung-soc-s3c-5.10' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into arm/soc
Samsung S3C24xx and S3C64xx machine code cleanup for v5.10
Big cleanup for the Samsung S3C24xx and S3C64xx platforms, although it
also touches files shared with S5Pv210 and Exynos. This is mostly Arnd
Bergmann work which Krzysztof Kozlowski took over, rebased and polished.
The goal is to cleanup, merge and finally make the Samsung S3C24xx and
S3C64xx architectures multiplatform. The multiplatform did not happen
yet here - just cleaning up and merging into one arch/arm/mach-s3c
directory. However this is step forward for multiplatform or at least
to keep this code still maintainable.
This pulls also branch with changes for Samsung SoC sound drivers from
broonie/sound because the cleanups there were part of this series and
all further patches depend on them.
* tag 'samsung-soc-s3c-5.10' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux: (62 commits)
ARM: s3c: Avoid naming clash of S3C24xx and S3C64xx timer setup
ARM: s3c: Cleanup from old plat-samsung include
ARM: s3c: make headers local if possible
ARM: s3c: move into a common directory
ARM: s3c24xx: stop including mach/hardware.h from mach/io.h
cpufreq: s3c24xx: move low-level clk reg access into platform code
cpufreq: s3c2412: use global s3c2412_cpufreq_setrefresh
ARM: s3c: remove cpufreq header dependencies
cpufreq: s3c24xx: split out registers
fbdev: s3c2410fb: remove mach header dependency
ARM: s3c24xx: bast: avoid irq_desc array usage
ARM: s3c24xx: spi: avoid hardcoding fiq number in driver
ARM: s3c24xx: include mach/irqs.h where needed
ARM: s3c24xx: move s3cmci pinctrl handling into board files
ARM: s3c24xx: move iis pinctrl config into boards
ARM: s3c24xx: move spi fiq handler into platform
ARM: s3c: adc: move header to linux/soc/samsung
ARM: s3c24xx: move irqchip driver back into platform
ARM: s3c24xx: move regs-spi.h into spi driver
ARM: s3c64xx: remove mach/hardware.h
...
Link: https://lore.kernel.org/r/20200831154751.7551-1-krzk@kernel.org
Signed-off-by: Olof Johansson <olof@lixom.net>
The IEPCLK_MUX is present on all SoCs whereas the CORECLK_MUX is present
only on AM65x SoCs and J721E. Add support for both these CLK muxes.
This allows the clock rates and clock parents for these to be controlled
through DT leveraging the clk infrastructure for configuring the default
parents and rates.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Grzegorz Jaszczyk <grzegorz.jaszczyk@linaro.org>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Current implementation of the genpd support over TI SCI uses a single
genpd across the whole SoC, and attaches multiple devices to this. This
solution has its drawbacks, like it is currently impossible to attach
more than one power domain to a device; the core genpd implementation
requires one genpd per power-domain entry in DT for a single device.
Also, some devices like USB apparently require their own genpd during
probe time, the current shared approach in use does not work at all.
Switch the implementation over to use a single genpd per power domain
entry in DT. The domains are registered with the onecell approach, but
we also add our own xlate service due to recent introduction of the
extended flag for TI SCI PM domains; genpd core xlate service requires
a single cell per powerdomain, but we are using two cells.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
The K3 J721E family of SoCs have a revised version of the PRU-ICSS (ICSSG)
processor subsystem present on K3 AM65x SoCs. These SoCs contain typically
two ICSSG instances named ICSSG0 and ICSSG1. The two ICSSGs are identical
to each other for the most part with minor SoC integration differences and
capabilities. The ICSSG1 supports slightly enhanced features like SGMII
mode Ethernet, while the ICSSG0 instance is limited to MII mode only.
There is no change in the Interrupt Controller w.r.t AM65x. All other
integration aspects are very similar to the ICSSGs on AM65x SoCs.
The existing pruss platform driver has been updated to support these new
ICSSG instances through new J721E specific compatibles.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Grzegorz Jaszczyk <grzegorz.jaszczyk@linaro.org>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
The K3 AM65x family of SoCs have the next generation of the PRU-ICSS
processor subsystem capable of supporting Gigabit Ethernet, and is
commonly referred to as ICSSG. These SoCs contain typically three
ICSSG instances named ICSSG0, ICSSG1 and ICSSG2. The three ICSSGs are
identical to each other for the most part with minor SoC integration
differences and capabilities. The ICSSG2 supports slightly enhanced
features like SGMII mode Ethernet, while the ICSS0 and ICSSG1 instances
are limited to MII mode only.
The ICSSGs on K3 AM65x SoCs are in general super-sets of the PRUSS on the
AM57xx/66AK2G SoCs. They include two additional auxiliary PRU cores called
RTUs and few other additional sub-modules. The interrupt integration is
also different on the K3 AM65x SoCs and are propagated through various
SoC-level Interrupt Router and Interrupt Aggregator blocks. Other IP level
differences include different constant tables, differences in system event
interrupt input sources etc. They also do not have a programmable module
reset line like those present on AM33xx/AM43xx SoCs. The modules are reset
just like any other IP with the SoC's global cold/warm resets.
The existing pruss platform driver has been updated to support these new
ICSSG instances through new AM65x specific compatibles. A build dependency
with ARCH_K3 is added to enable building all the existing PRUSS platform
drivers for this ARMv8 platform.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Grzegorz Jaszczyk <grzegorz.jaszczyk@linaro.org>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
The 66AK2G SoC supports two PRU-ICSS instances, named PRUSS0 and PRUSS1,
each of which has two PRU processor cores. The two PRU-ICSS instances
are identical to each other with few minor SoC integration differences,
and are very similar to the PRU-ICSS1 of AM57xx/AM43xx. The Shared Data
RAM size is larger and the number of interrupts coming into MPU INTC
is like the instances on AM437x. There are also few other differences
attributing to integration in Keystone architecture (like no SYSCFG
register or PRCM handshake protocols). Other IP level differences
include different constant table, differences in system event interrupt
input sources etc. They also do not have a programmable module reset
line like those present on AM33xx/AM43xx SoCs. The modules are reset
just like any other IP with the SoC's global cold/warm resets.
The existing PRUSS platform driver has been enhanced to support these
66AK2G PRU-ICSS instances through new 66AK2G specific compatible for
properly probing and booting all the different PRU cores in each
PRU-ICSS processor subsystem. A build dependency with ARCH_KEYSTONE
is added to enable the driver to be built in K2G-only configuration.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Grzegorz Jaszczyk <grzegorz.jaszczyk@linaro.org>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
The AM57xx family of SoCs supports two PRU-ICSS instances, each of
which has two PRU processor cores. The two PRU-ICSS instances are
identical to each other, and are very similar to the PRU-ICSS1 of
AM33xx/AM43xx except for a few minor differences like the RAM sizes
and the number of interrupts coming into the MPU INTC. They do
not have a programmable module reset line unlike those present on
AM33xx/AM43xx SoCs. The modules are reset just like any other IP
with the SoC's global cold/warm resets. Each PRU-ICSS's INTC is also
preceded by a Crossbar that enables multiple external events to be
routed to a specific number of input interrupt events. Any interrupt
event directed towards PRUSS needs this crossbar to be setup properly
on the firmware side.
The existing PRUSS platform driver has been enhanced to support
these AM57xx PRU-ICSS instances through new AM57xx specific
compatible for properly probing and booting all the different PRU
cores in each PRU-ICSS processor subsystem. A build dependency with
SOC_DRA7XX is also added to enable the driver to be built in
AM57xx-only configuration (there is no separate Kconfig option
for AM57xx vs DRA7xx).
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Grzegorz Jaszczyk <grzegorz.jaszczyk@linaro.org>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
The AM437x SoCs have two different PRU-ICSS subsystems: PRU-ICSS1
and a smaller PRU-ICSS0. Enhance the PRUSS platform driver to support
both the PRU-ICSS sub-systems on these SoCs.
The PRU-ICSS1 on AM437x is very similar to the PRU-ICSS on AM33xx
except for few minor differences - increased Instruction RAM, increased
Shared Data RAM2, and 1 less interrupt (PRUSS host interrupt 7 which is
redirected to the other PRUSS) towards the MPU INTC. The PRU-ICSS0 is
a cut-down version of the IP, with less DRAM per PRU, no Shared DRAM etc.
It also does not have direct access to L3 bus regions, there is a single
interface to L3 for both PRUSS0 and PRUSS1, and it would have to go
through the PRUSS1's interface. The PRUSS_SYSCFG register is reserved on
PRUSS0, so any external access requires the programming the corresponding
PRUSS_SYSCFG register in PRUSS1. It does have its own dedicated I/O lines
though. Note that this instance does not support any PRU Ethernet related
use cases.
The adaptation uses SoC-specific compatibles in the driver and uses
a newly introduced pruss_match_private_data structure and the
pruss_get_private_data() function to retrieve a PRUSS instance specific
data using a device-name based lookup logic. The reset and the L3 external
access are managed by the parent interconnect ti-sysc bus driver so that
PRUSS1 and PRUSS0 can be independently supported.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Grzegorz Jaszczyk <grzegorz.jaszczyk@linaro.org>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
The Programmable Real-Time Unit - Industrial Communication
Subsystem (PRU-ICSS) is present on various TI SoCs such as
AM335x or AM437x or the Keystone 66AK2G. Each SoC can have
one or more PRUSS instances that may or may not be identical.
For example, AM335x SoCs have a single PRUSS, while AM437x has
two PRUSS instances PRUSS1 and PRUSS0, with the PRUSS0 being
a cut-down version of the PRUSS1.
The PRUSS consists of dual 32-bit RISC cores called the
Programmable Real-Time Units (PRUs), some shared, data and
instruction memories, some internal peripheral modules, and
an interrupt controller. The programmable nature of the PRUs
provide flexibility to implement custom peripheral interfaces,
fast real-time responses, or specialized data handling.
The PRU-ICSS functionality is achieved through three different
platform drivers addressing a specific portion of the PRUSS.
Some sub-modules of the PRU-ICSS IP reuse some of the existing
drivers (like davinci mdio driver or the generic syscon driver).
This design provides flexibility in representing the different
modules of PRUSS accordingly, and at the same time allowing the
PRUSS driver to add some instance specific configuration within
an SoC.
The PRUSS platform driver deals with the overall PRUSS and is
used for managing the subsystem level resources like various
memories and the CFG module. It is responsible for the creation
and deletion of the platform devices for the child PRU devices
and other child devices (like Interrupt Controller, MDIO node
and some syscon nodes) so that they can be managed by specific
platform drivers. The PRUSS interrupt controller is managed by
an irqchip driver, while the individual PRU RISC cores are
managed by a PRU remoteproc driver.
The driver currently supports the AM335x SoC, and support for
other TI SoCs will be added in subsequent patches.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Grzegorz Jaszczyk <grzegorz.jaszczyk@linaro.org>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
The AM65x SR2.0 Ringacc has fixed errata i2023 "RINGACC, UDMA: RINGACC and
UDMA Ring State Interoperability Issue after Channel Teardown". This errata
also fixed for J271E SoC.
Use SOC bus data for K3 SoC identification and enable i2023 errate w/a only
for the AM65x SR1.0. This also makes obsolete "ti,dma-ring-reset-quirk" DT
property.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Eliminate the following coccicheck warning:
drivers/soc/sunxi/sunxi_sram.c:197:2-3: Unneeded semicolon
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20200910140546.1191280-1-yanaijie@huawei.com
The busy loop in rpmh_rsc_send_data() is written with the assumption
that the udelay will be preempted by the tcs_tx_done() irq handler when
the TCS slots are all full. This doesn't hold true when the calling
thread is an irqthread and the tcs_tx_done() irq is also an irqthread.
That's because kernel irqthreads are SCHED_FIFO and thus need to
voluntarily give up priority by calling into the scheduler so that other
threads can run.
I see RCU stalls when I boot with irqthreads on the kernel commandline
because the modem remoteproc driver is trying to send an rpmh async
message from an irqthread that needs to give up the CPU for the rpmh
irqthread to run and clear out tcs slots.
rcu: INFO: rcu_preempt self-detected stall on CPU
rcu: 0-....: (1 GPs behind) idle=402/1/0x4000000000000002 softirq=2108/2109 fqs=4920
(t=21016 jiffies g=2933 q=590)
Task dump for CPU 0:
irq/11-smp2p R running task 0 148 2 0x00000028
Call trace:
dump_backtrace+0x0/0x154
show_stack+0x20/0x2c
sched_show_task+0xfc/0x108
dump_cpu_task+0x44/0x50
rcu_dump_cpu_stacks+0xa4/0xf8
rcu_sched_clock_irq+0x7dc/0xaa8
update_process_times+0x30/0x54
tick_sched_handle+0x50/0x64
tick_sched_timer+0x4c/0x8c
__hrtimer_run_queues+0x21c/0x36c
hrtimer_interrupt+0xf0/0x22c
arch_timer_handler_phys+0x40/0x50
handle_percpu_devid_irq+0x114/0x25c
__handle_domain_irq+0x84/0xc4
gic_handle_irq+0xd0/0x178
el1_irq+0xbc/0x180
save_return_addr+0x18/0x28
return_address+0x54/0x88
preempt_count_sub+0x40/0x88
_raw_spin_unlock_irqrestore+0x4c/0x6c
___ratelimit+0xd0/0x128
rpmh_rsc_send_data+0x24c/0x378
__rpmh_write+0x1b0/0x208
rpmh_write_async+0x90/0xbc
rpmhpd_send_corner+0x60/0x8c
rpmhpd_aggregate_corner+0x8c/0x124
rpmhpd_set_performance_state+0x8c/0xbc
_genpd_set_performance_state+0xdc/0x1b8
dev_pm_genpd_set_performance_state+0xb8/0xf8
q6v5_pds_disable+0x34/0x60 [qcom_q6v5_mss]
qcom_msa_handover+0x38/0x44 [qcom_q6v5_mss]
q6v5_handover_interrupt+0x24/0x3c [qcom_q6v5]
handle_nested_irq+0xd0/0x138
qcom_smp2p_intr+0x188/0x200
irq_thread_fn+0x2c/0x70
irq_thread+0xfc/0x14c
kthread+0x11c/0x12c
ret_from_fork+0x10/0x18
This busy loop naturally lends itself to using a wait queue so that each
thread that tries to send a message will sleep waiting on the waitqueue
and only be woken up when a free slot is available. This should make
things more predictable too because the scheduler will be able to sleep
tasks that are waiting on a free tcs instead of the busy loop we
currently have today.
Reviewed-by: Maulik Shah <mkshah@codeaurora.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Maulik Shah <mkshah@codeaurora.org>
Cc: Lina Iyer <ilina@codeaurora.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20200724211711.810009-1-sboyd@kernel.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
For easy understanding of architecture and alphabetical merging, this
patch uses ARM32/ARM64 for description.
This prepares for sorting the menu.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87bliiv54u.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Change the RACPREFDATA(x) setting to prefetch the next 256-byte line
after 4 consecutive lines have been used, instead of after 2 consecutive
lines. This does improve the synthetic memcpy benchmark by an additional
+0.5% on top of the previous change for Cortex-A72 CPUs.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Change the RAC prefetch distance from +/- 1 to +/- 2 for Cortex-A72 CPUs
since this provides an average of a 3.8% performance increase for
synthetic memcpy benchmarks.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
72165 uses a Brahma-B53 CPU and its Bus Interface Unit, tune it
according to the existing values we have.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
72164 uses a Brahma-B53 CPU and its Bus Interface Unit, tune it
according to the existing values we have.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Now, Renesas SoC drivers are under menu, but current descriptions are
not aligned.
This patch aligns them.
- Emma Mobile EV2
- RZ/A1H (R7S72100)
...
- R-Car H2 (R8A77900)
...
- Renesas R-Car H3 ES1.x SoC Platform
...
- R-Car H2 System Controller support
- R-Car M2-W/N System Controller support
- R-Car V2H System Controller support
- R-Car E2 System Controller support
- R-Car H3 System Controller support
- R-Car M3-W System Controller support
- R-Car M3-W+ System Controller support
- R-Car M3-N System Controller support
+ SoC Platform support for Emma Mobile EV2
+ SoC Platform support for RZ/A1H+
...
+ SoC Platform support for R-Car H2
...
+ SoC Platform support for R-Car H3 ES1.x
...
+ System Controller support for R-Car H2
+ System Controller support for R-Car M2-W/N
+ System Controller support for R-Car V2H
+ System Controller support for R-Car E2
+ System Controller support for R-Car H3
+ System Controller support for R-Car M3-W
+ System Controller support for R-Car M3-W+
+ System Controller support for R-Car M3-N
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87zh6kyedc.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Renesas related SoC settings are located on TOP level menu,
thus it is very verbose.
This patch groups Renesas related settings into
"Renesas SoC driver support" menu.
And it aligns config menu names.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87k0xxho7t.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The OPP core manages various resources, e.g. clocks or interconnect paths.
These resources are looked up when the OPP table is allocated once
dev_pm_opp_get_opp_table() is called the first time (either directly
or indirectly through one of the many helper functions).
At this point, the resources may not be available yet, i.e. looking them
up will result in -EPROBE_DEFER. Unfortunately, dev_pm_opp_get_opp_table()
is currently unable to propagate this error code since it only returns
the allocated OPP table or NULL.
This means that all consumers of the OPP core are required to make sure
that all necessary resources are available. Usually this happens by
requesting them, checking the result and releasing them immediately after.
For example, we have added "dev_pm_opp_of_find_icc_paths(dev, NULL)" to
several drivers now just to make sure the interconnect providers are
ready before the OPP table is allocated. If this call is missing,
the OPP core will only warn about this and then attempt to continue
without interconnect. This will eventually fail horribly, e.g.:
cpu cpu0: _allocate_opp_table: Error finding interconnect paths: -517
... later ...
of: _read_bw: Mismatch between opp-peak-kBps and paths (1 0)
cpu cpu0: _opp_add_static_v2: opp key field not found
cpu cpu0: _of_add_opp_table_v2: Failed to add OPP, -22
This example happens when trying to use interconnects for a CPU OPP
table together with qcom-cpufreq-nvmem.c. qcom-cpufreq-nvmem calls
dev_pm_opp_set_supported_hw(), which ends up allocating the OPP table
early. To fix the problem with the current approach we would need to add
yet another call to dev_pm_opp_of_find_icc_paths(dev, NULL).
But actually qcom-cpufreq-nvmem.c has nothing to do with interconnects...
This commit attempts to make this more robust by allowing
dev_pm_opp_get_opp_table() to return an error pointer. Fixing all
the usages is trivial because the function is usually used indirectly
through another helper (e.g. dev_pm_opp_set_supported_hw() above).
These other helpers already return an error pointer.
The example above then works correctly because set_supported_hw() will
return -EPROBE_DEFER, and qcom-cpufreq-nvmem.c already propagates that
error. It should also be possible to remove the remaining usages of
"dev_pm_opp_of_find_icc_paths(dev, NULL)" from other drivers as well.
Note that this commit currently only handles -EPROBE_DEFER for the
clock/interconnects within _allocate_opp_table(). Other errors are just
ignored as before. Eventually those should be propagated as well.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
[ Viresh: skip checking return value of dev_pm_opp_get_opp_table() for
EPROBE_DEFER in domain.c, fix NULL return value and reorder
code a bit in core.c, and update exynos-asv.c ]
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
We must re-enable the RTC module clock enabled in RTC+DDR suspend, and
pm33xx has been using platform data callbacks for that. Looks like for
retention suspend the RTC module clock must not be re-enabled.
To remove the legacy platform data callbacks, and eventually be able to
drop the RTC legacy platform data, let's manage the RTC module clock
and register range directly in pm33xx.
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
dev_err_probe() can reduce code size, uniform error handling and record the
defer probe reason etc., use it to simplify the code.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
There is no need to have the 'struct regmap *syscon_regmap' variable
static since new value always be assigned before use it.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20200715024701.28356-1-yuehaibing@huawei.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This is the only part of plat-samsung that is really
shared between the s3c and s5p ports. Moving it to
drivers/soc/ lets us make them completely independent.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20200806182059.2431-16-krzk@kernel.org
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Let's add omap4 and 5 l4_abe interconnect instance for the power
domain.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Let's configure only sgx power domain for am3 and am4 to start with.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The PRM controller has currently only support for resets while the power
domains are still handled in the platform code.
Let's add basic power domain support to enable and disable a PRM
controlled power domain if configured in the devicetree. This can be
used for various hardware accelerators, and interconnect instances.
Further support can be added later on as needed for runtime configuration
based on domain-idle-states.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
BCM6318, BCM6328, BCM6362 and BCM63268 SoCs have a power domain controller
to enable/disable certain components in order to save power.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Florian Fainelli <F.fainelli@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Brahma-B53 and Cortex-A72 CPUs integrated on Broadcom STB SoCs feature a
read-ahead cache that performs cache line size adaptation between the
bus interface unit and the memory controller.
On 32-bit ARM kernels we have to resort to a full featured read-ahead
cache driver under arch/arm/mm/cache-b15-rac.c (CONFIG_CACHE_B15_RAC)
because there are still cache maintenance operations by set/ways/index
that cannot be transparently handled by the ARM Coherency Extension that
the read-ahead cache interfaces to.
The 64-bit ARM kernel however has long deprecated all of those, so this
is simply a one time configuration.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Pull misc vfs updates from Al Viro:
"No common topic whatsoever in those, sorry"
* 'work.misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
fs: define inode flags using bit numbers
iov_iter: Move unnecessary inclusion of crypto/hash.h
dlmfs: clean up dlmfs_file_{read,write}() a bit
framework we just have some minor tweaks and a debugfs feature, so not much to
see there. The driver updates are fairly well split between AT91 and Qualcomm
clk support. Adding those two drivers together equals about 50% of the
diffstat. Otherwise, the big amount of work this time was on supporting
Broadcom's Raspberry Pi firmware clks. See below for some more highlights.
Core:
- Document clk_hw_round_rate() so it gets some more use
- Remove unused __clk_get_flags()
- Add a prepare/enable debugfs feature similar to rate setting
New Drivers:
- Add support for SAMA7G5 SoC clks
- Enable CPU clks on Qualcomm IPQ6018 SoCs
- Enable CPU clks on Qualcomm MSM8996 SoCs
- GPU clk support for Qualcomm SM8150 and SM8250 SoCs
- Audio clks on Qualcomm SC7180 SoCs
- Microchip Sparx5 DPLL clk
- Add support for the new Renesas RZ/G2H (R8A774E1) SoC
Updates:
- Make defines for bcm63xx-gate clks to use in DT
- Support BCM2711 SoC firmware clks
- Add HDMI clks for BCM2711 SoCs
- Add RTC related clks on Ingenic SoCs
- Support USB PHY clks on Ingenic SoCs
- Support gate clks on BCM6318 SoCs
- RMU and DMAC/GPIO clock support for Actions Semi S500 SoCs
- Use poll_timeout functions in Rockchip clk driver
- Support Rockchip rk3288w SoC variant
- Mark mac_lbtest critical on Rockchip rk3188
- Add CAAM clock support for i.MX vf610 driver
- Add MU root clock support for i.MX imx8mp driver
- Amlogic g12: add neural network accelerator clock sources
- Amlogic meson8: remove critical flag for main PLL divider
- Amlogic meson8: add video decoder clock gates
- Convert one more Renesas DT binding to json-schema
- Enhance critical clock handling on Renesas platforms to only consider
clocks that were enabled at boot time
-----BEGIN PGP SIGNATURE-----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=QLRg
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"It looks like a smaller batch of clk updates this time around.
In the core framework we just have some minor tweaks and a debugfs
feature, so not much to see there. The driver updates are fairly well
split between AT91 and Qualcomm clk support. Adding those two drivers
together equals about 50% of the diffstat.
Otherwise, the big amount of work this time was on supporting
Broadcom's Raspberry Pi firmware clks.
Highlights:
Core:
- Document clk_hw_round_rate() so it gets some more use
- Remove unused __clk_get_flags()
- Add a prepare/enable debugfs feature similar to rate setting
New Drivers:
- Add support for SAMA7G5 SoC clks
- Enable CPU clks on Qualcomm IPQ6018 SoCs
- Enable CPU clks on Qualcomm MSM8996 SoCs
- GPU clk support for Qualcomm SM8150 and SM8250 SoCs
- Audio clks on Qualcomm SC7180 SoCs
- Microchip Sparx5 DPLL clk
- Add support for the new Renesas RZ/G2H (R8A774E1) SoC
Updates:
- Make defines for bcm63xx-gate clks to use in DT
- Support BCM2711 SoC firmware clks
- Add HDMI clks for BCM2711 SoCs
- Add RTC related clks on Ingenic SoCs
- Support USB PHY clks on Ingenic SoCs
- Support gate clks on BCM6318 SoCs
- RMU and DMAC/GPIO clock support for Actions Semi S500 SoCs
- Use poll_timeout functions in Rockchip clk driver
- Support Rockchip rk3288w SoC variant
- Mark mac_lbtest critical on Rockchip rk3188
- Add CAAM clock support for i.MX vf610 driver
- Add MU root clock support for i.MX imx8mp driver
- Amlogic g12: add neural network accelerator clock sources
- Amlogic meson8: remove critical flag for main PLL divider
- Amlogic meson8: add video decoder clock gates
- Convert one more Renesas DT binding to json-schema
- Enhance critical clock handling on Renesas platforms to only
consider clocks that were enabled at boot time"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (79 commits)
clk: qcom: gcc: Make disp gpll0 branch aon for sc7180/sdm845
ipq806x: gcc: add support for child probe
clk: qcom: msm8996: Make symbol 'cpu_msm8996_clks' static
clk: qcom: ipq8074: Add correct index for PCIe clocks
clk: <linux/clk-provider.h>: drop a duplicated word
clk: renesas: cpg-mssr: Add r8a774e1 support
dt-bindings: clock: renesas,cpg-mssr: Document r8a774e1
clk: Drop duplicate selection in Kconfig
clk: qcom: smd: Add support for MSM8992/4 rpm clocks
clk: qcom: ipq8074: Add missing clocks for pcie
dt-bindings: clock: qcom: ipq8074: Add missing bindings for PCIe
Replace HTTP links with HTTPS ones: Common CLK framework
clk: qcom: Add CPU clock driver for msm8996
dt-bindings: clk: qcom: Add bindings for CPU clock for msm8996
soc: qcom: Separate kryo l2 accessors from PMU driver
clk: meson: meson8b: add the vclk2_en gate clock
clk: meson: meson8b: add the vclk_en gate clock
clk: qcom: Fix return value check in apss_ipq6018_probe()
clk: bcm: dvp: Add missing module informations
clk: meson: meson8b: Drop CLK_IS_CRITICAL from fclk_div2
...
A couple of subsystems have their own subsystem maintainers but choose
to have the code merged through the soc tree as upstream, as the code
tends to be used across multiple SoCs or has SoC specific drivers itself:
- memory controllers:
Krzysztof Kozlowski takes ownership of the drivers/memory
subsystem and its drivers, starting out with a set of cleanup
patches.
A larger driver for the Tegra memory controller that was accidentally
missed for v5.8 is now added.
- reset controllers:
Only minor updates to drivers/reset this time
- firmware:
The "turris mox" firmware driver gains support for signed firmware blobs
The tegra firmware driver gets extended to export some debug information
Various updates to i.MX firmware drivers, mostly cosmetic
- ARM SCMI/SCPI:
A new mechanism for platform notifications is added, among a number
of minor changes.
- optee:
Probing of the TEE bus is rewritten to better support detection of
devices that depend on the tee-supplicant user space.
A new firmware based trusted platform module (fTPM) driver is added
based on OP-TEE
- SoC attributes:
A new driver is added to provide a generic soc_device for identifying
a machine through the SMCCC ARCH_SOC_ID firmware interface rather than
by probing SoC family specific registers.
The series also contains some cleanups to the common soc_device code.
There are also a number of updates to SoC specific drivers,
the main ones are:
- Mediatek cmdq driver gains a few in-kernel interfaces
- Minor updates to Qualcomm RPMh, socinfo, rpm drivers, mostly adding
support for additional SoC variants
- The Qualcomm GENI core code gains interconnect path voting and
performance level support, and integrating this into a number of
device drivers.
- A new driver for Samsung Exynos5800 voltage coupler for
- Renesas RZ/G2H (R8A774E1) SoC support gets added to a couple of SoC
specific device drivers
- Updates to the TI K3 Ring Accelerator driver
-----BEGIN PGP SIGNATURE-----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=nezz
-----END PGP SIGNATURE-----
Merge tag 'arm-drivers-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"A couple of subsystems have their own subsystem maintainers but choose
to have the code merged through the soc tree as upstream, as the code
tends to be used across multiple SoCs or has SoC specific drivers
itself:
- memory controllers:
Krzysztof Kozlowski takes ownership of the drivers/memory subsystem
and its drivers, starting out with a set of cleanup patches.
A larger driver for the Tegra memory controller that was
accidentally missed for v5.8 is now added.
- reset controllers:
Only minor updates to drivers/reset this time
- firmware:
The "turris mox" firmware driver gains support for signed firmware
blobs The tegra firmware driver gets extended to export some debug
information Various updates to i.MX firmware drivers, mostly
cosmetic
- ARM SCMI/SCPI:
A new mechanism for platform notifications is added, among a number
of minor changes.
- optee:
Probing of the TEE bus is rewritten to better support detection of
devices that depend on the tee-supplicant user space. A new
firmware based trusted platform module (fTPM) driver is added based
on OP-TEE
- SoC attributes:
A new driver is added to provide a generic soc_device for
identifying a machine through the SMCCC ARCH_SOC_ID firmware
interface rather than by probing SoC family specific registers.
The series also contains some cleanups to the common soc_device
code.
There are also a number of updates to SoC specific drivers, the main
ones are:
- Mediatek cmdq driver gains a few in-kernel interfaces
- Minor updates to Qualcomm RPMh, socinfo, rpm drivers, mostly adding
support for additional SoC variants
- The Qualcomm GENI core code gains interconnect path voting and
performance level support, and integrating this into a number of
device drivers.
- A new driver for Samsung Exynos5800 voltage coupler for
- Renesas RZ/G2H (R8A774E1) SoC support gets added to a couple of SoC
specific device drivers
- Updates to the TI K3 Ring Accelerator driver"
* tag 'arm-drivers-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (164 commits)
soc: qcom: geni: Fix unused label warning
soc: qcom: smd-rpm: Fix kerneldoc
memory: jz4780_nemc: Only request IO memory the driver will use
soc: qcom: pdr: Reorder the PD state indication ack
MAINTAINERS: Add Git repository for memory controller drivers
memory: brcmstb_dpfe: Fix language typo
memory: samsung: exynos5422-dmc: Correct white space issues
memory: samsung: exynos-srom: Correct alignment
memory: pl172: Enclose macro argument usage in parenthesis
memory: of: Correct kerneldoc
memory: omap-gpmc: Fix language typo
memory: omap-gpmc: Correct white space issues
memory: omap-gpmc: Use 'unsigned int' for consistency
memory: omap-gpmc: Enclose macro argument usage in parenthesis
memory: omap-gpmc: Correct kerneldoc
memory: mvebu-devbus: Align with open parenthesis
memory: mvebu-devbus: Add missing braces to all arms of if statement
memory: bt1-l2-ctl: Add blank lines after declarations
soc: TI knav_qmss: make symbol 'knav_acc_range_ops' static
firmware: ti_sci: Replace HTTP links with HTTPS ones
...
This fixes a potential race condition with remoteprocs by not sending
acknowledgements until after registered drivers has processed the event.
It adds IPQ6018 support to the SMD RPM driver, fixes kerneldoc in the
same and converts the related DT binding to YAML.
Finally it fixes a compilation warning in the geni serial engine driver
when compiled without CONFIG_SERIAL_EARLYCON.
-----BEGIN PGP SIGNATURE-----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=7TeI
-----END PGP SIGNATURE-----
Merge tag 'qcom-drivers-for-5.9-2' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into arm/drivers
Qualcomm driver additional updates for 5.9
This fixes a potential race condition with remoteprocs by not sending
acknowledgements until after registered drivers has processed the event.
It adds IPQ6018 support to the SMD RPM driver, fixes kerneldoc in the
same and converts the related DT binding to YAML.
Finally it fixes a compilation warning in the geni serial engine driver
when compiled without CONFIG_SERIAL_EARLYCON.
* tag 'qcom-drivers-for-5.9-2' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
soc: qcom: geni: Fix unused label warning
soc: qcom: smd-rpm: Fix kerneldoc
soc: qcom: pdr: Reorder the PD state indication ack
dt-bindings: soc: qcom: smd-rpm: Convert binding to YAML schema
soc: qcom: smd-rpm: Add IPQ6018 compatible
dt-bindings: soc: qcom: smd-rpm: Add IPQ6018 compatible
Link: https://lore.kernel.org/r/20200730051852.649761-1-bjorn.andersson@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
If CONFIG_SERIAL_EARLYCON is not set, gcc warns this:
drivers/soc/qcom/qcom-geni-se.c: In function 'geni_se_probe'
drivers/soc/qcom/qcom-geni-se.c:914:1: warning: label 'exit' defined but not used [-Wunused-label]
exit:
^~~~
Fixes: 048eb908a1 ("soc: qcom-geni-se: Add interconnect support to fix earlycon crash")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20200722020619.25988-1-yuehaibing@huawei.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Fix W=1 compile warnings (invalid kerneldoc):
drivers/soc/qcom/smd-rpm.c:35: warning: Function parameter or member 'dev' not described in 'qcom_smd_rpm'
drivers/soc/qcom/smd-rpm.c:99: warning: Function parameter or member 'state' not described in 'qcom_rpm_smd_write'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200729074415.28393-2-krzk@kernel.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The Protection Domains (PD) have a mechanism to keep its resources
enabled until the PD down indication is acked. Reorder the PD state
indication ack so that clients get to release the relevant resources
before the PD goes down.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Rishabh Bhatnagar <rishabhb@codeaurora.org>
Fixes: fbe639b44a ("soc: qcom: Introduce Protection Domain Restart helpers")
Reported-by: Rishabh Bhatnagar <rishabhb@codeaurora.org>
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Link: https://lore.kernel.org/r/20200701195954.9007-1-sibis@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
- TI K3 Ring Accelerator updates
- Few non critical warining fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Y8Sq
-----END PGP SIGNATURE-----
Merge tag 'drivers_soc_for_5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone into arm/drivers
SOC: TI Keystone driver update for v5.9
- TI K3 Ring Accelerator updates
- Few non critical warining fixes
* tag 'drivers_soc_for_5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone:
soc: TI knav_qmss: make symbol 'knav_acc_range_ops' static
firmware: ti_sci: Replace HTTP links with HTTPS ones
soc: ti/ti_sci_protocol.h: drop a duplicated word + clarify
soc: ti: k3: fix semicolon.cocci warnings
soc: ti: k3-ringacc: fix: warn: variable dereferenced before check 'ring'
dmaengine: ti: k3-udma: Switch to k3_ringacc_request_rings_pair
soc: ti: k3-ringacc: separate soc specific initialization
soc: ti: k3-ringacc: add request pair of rings api.
soc: ti: k3-ringacc: add ring's flags to dump
soc: ti: k3-ringacc: Move state tracking variables under a struct
dt-bindings: soc: ti: k3-ringacc: convert bindings to json-schema
Link: https://lore.kernel.org/r/1595711814-7015-1-git-send-email-santosh.shilimkar@oracle.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The sparse tool complains as follows:
drivers/soc/ti/knav_qmss_acc.c:453:23: warning:
symbol 'knav_acc_range_ops' was not declared. Should it be static?
'knav_acc_range_ops' is not used outside of knav_qmss_acc.c,
so marks it static.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Separate SoC specific initialization and and OF mach data in preparation of
adding support for more K3 SoCs
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Add new API k3_ringacc_request_rings_pair() to request pair of rings at
once, as in the most cases Rings are used with DMA channels, which need to
request pair of rings - one to feed DMA with descriptors (TX/RX FDQ) and
one to receive completions (RX/TX CQ). This will allow to simplify Ringacc
API users.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Add struct k3_ring *ring->flags to the ring dump.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Move the free, occ, windex and rindex under a struct. We can use memset to
zero them and it will allow a cleaner way to extend driver functionality in
the future,
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
For RPMh this fixes an issue where ktime was used during suspend, allows
the driver to be used on ARM targets and some minor cleanups.
It adds support for the latest format version in the socinfo driver and
adds identifiers for SM8250 and SDM630.
SMD-RPM gains compatibles for MSM8994 and MSM8936 and the Qualcomm SCM
gains compatibles MSM8994 and IPQ8074.
The GENI core code gains interconnect path voting and performance level
support, with subsequent patches integrating this with the SPI, I2C,
UART and QSPI drivers.
Following this the KGDB support for the GENI serial driver is improved,
the performance related to chip-select is improved for SPI and QSPI.
-----BEGIN PGP SIGNATURE-----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=Os4F
-----END PGP SIGNATURE-----
Merge tag 'qcom-drivers-for-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into arm/drivers
Qualcomm driver updates for v5.9
For RPMh this fixes an issue where ktime was used during suspend, allows
the driver to be used on ARM targets and some minor cleanups.
It adds support for the latest format version in the socinfo driver and
adds identifiers for SM8250 and SDM630.
SMD-RPM gains compatibles for MSM8994 and MSM8936 and the Qualcomm SCM
gains compatibles MSM8994 and IPQ8074.
The GENI core code gains interconnect path voting and performance level
support, with subsequent patches integrating this with the SPI, I2C,
UART and QSPI drivers.
Following this the KGDB support for the GENI serial driver is improved,
the performance related to chip-select is improved for SPI and QSPI.
* tag 'qcom-drivers-for-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (35 commits)
soc: qcom: geni: Fix NULL pointer dereference
tty: serial: qcom-geni-serial: Drop the icc bw votes in suspend for console
serial: qcom_geni_serial: Always use 4 bytes per TX FIFO word
serial: qcom_geni_serial: Make kgdb work even if UART isn't console
spi: spi-geni-qcom: Get rid of most overhead in prepare_message()
spi: spi-geni-qcom: Set the clock properly at runtime resume
spi: spi-geni-qcom: Avoid clock setting if not needed
spi: spi-qcom-qspi: Set an autosuspend delay of 250 ms
spi: spi-qcom-qspi: Avoid clock setting if not needed
spi: spi-qcom-qspi: Use OPP API to set clk/perf state
firmware: qcom_scm: Add msm8994 compatible
firmware: qcom_scm: Fix legacy convention SCM accessors
<linux/of.h>: add stub for of_get_next_parent() to fix qcom build error
dt-bindings: firmware: qcom: Add compatible for IPQ8074 SoC
spi: spi-geni-qcom: Use OPP API to set clk/perf state
tty: serial: qcom_geni_serial: Use OPP API to set clk/perf state
spi: spi-qcom-qspi: Add interconnect support
spi: spi-geni-qcom: Add interconnect support
spi: spi-geni-qcom: Combine the clock setting code
tty: serial: qcom_geni_serial: Add interconnect support
...
Link: https://lore.kernel.org/r/20200721044812.3429652-1-bjorn.andersson@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Update SCU irq code to call pm_system_wakeup() in general MU IRQ
handler, so that system can be waked up when MU IRQ arrives.
- Move i.MX SCU soc driver into imx firmware folder to get it
initialized from i.MX SCU firmware driver.
- Clean up soc-imx-scu driver a bit by using devm_kasprintf().
- Correct postfix setting for cm40 power domain in scu-pd driver.
- Add resource management support for IMX_SCU firmware driver.
- Add more cm4 resources to i.MX SCU power domain driver.
- Select ARM_GIC_V3 from SOC_IMX8M for being able to use GICv3 driver
in AARCH32 mode Linux on AARCH64 hardware.
-----BEGIN PGP SIGNATURE-----
iQFIBAABCgAyFiEEFmJXigPl4LoGSz08UFdYWoewfM4FAl8VPiUUHHNoYXduZ3Vv
QGtlcm5lbC5vcmcACgkQUFdYWoewfM5L9wf/VY0Q2oZ+gaJRNhSfVSf7O7QpscHV
mtQZPHg81jv3D2NkOpycJ1vaJEo118Ho6vb5IfeheChyZ2eWEJKkaPpVuhyKjPhK
B+nUmFnsTm8MTL+GKA1W7g6Gg+lJN3wT/mOITNmGMW0NID4/rse/XeM18+28nNb/
2svVyc1+4uTM5m+4i+scBCdnxgBK2H71/DQYLfDvNtZesWzas1PNN1nJh10D/PMM
X6d7AZ92c//pf5eR3wpm/JKZ+hubefBNWkrpw50pNlAASbgOogXWL1GU9q3r/VAV
9dS0dW9mIlpqlONEO+2zv9v1/RnoUypkCe/FFTUsA1bJ7ZGqhxWmrYwyfg==
=7Pd6
-----END PGP SIGNATURE-----
Merge tag 'imx-drivers-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/drivers
i.MX drivers change for 5.9:
- Update SCU irq code to call pm_system_wakeup() in general MU IRQ
handler, so that system can be waked up when MU IRQ arrives.
- Move i.MX SCU soc driver into imx firmware folder to get it
initialized from i.MX SCU firmware driver.
- Clean up soc-imx-scu driver a bit by using devm_kasprintf().
- Correct postfix setting for cm40 power domain in scu-pd driver.
- Add resource management support for IMX_SCU firmware driver.
- Add more cm4 resources to i.MX SCU power domain driver.
- Select ARM_GIC_V3 from SOC_IMX8M for being able to use GICv3 driver
in AARCH32 mode Linux on AARCH64 hardware.
* tag 'imx-drivers-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
soc: imx: select ARM_GIC_V3 for i.MX8M
firmware: imx: Move i.MX SCU soc driver into imx firmware folder
firmware: imx: scu-pd: add more cm4 resources
firmware: imx: add resource management api
firmware: imx: scu-pd: fix cm40 power domain
soc: imx: scu: use devm_kasprintf
firmware: imx: make sure MU irq can wake up system from suspend mode
Link: https://lore.kernel.org/r/20200720085536.24138-1-shawnguo@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add a simple custom voltage regulator coupler for Exynos5800 SoCs, which
require coupling between "vdd_arm" and "vdd_int" regulators. This coupler
ensures that the voltage values don't go below the bootloader-selected
operation point during the boot process until the clients set their
constraints. It is achieved by assuming minimal voltage value equal to
the current value if no constraints are set. This also ensures proper
voltage balancing if any of the client driver is missing.
The balancing code comes from the regulator/core.c with the additional
logic for handling regulators without client constraints applied added.
Link: https://lore.kernel.org/r/20200721180900.13844-5-krzk@kernel.org
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
pdev struct doesn't exits for the devices whose status are disabled
from DT node, in such cases NULL is returned from 'of_find_device_by_node'
Later when we try to get drvdata from pdev struct NULL pointer dereference
is triggered.
Add a NULL check for return values to fix the issue.
We were hitting this issue when one of QUP is disabled.
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Fixes: 048eb908a1 ("soc: qcom-geni-se: Add interconnect support to fix earlycon crash")
Reported-by: Sai Prakash Ranjan <saipraka@codeaurora.org>
Signed-off-by: Akash Asthana <akashast@codeaurora.org>
Link: https://lore.kernel.org/r/1594996342-26964-1-git-send-email-akashast@codeaurora.org
[bjorn: s/wrapper_pdev/pdev/]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This adds missing SoC IDs for Tegra186 and Tegra194 and fixes a typo in
a warning message.
-----BEGIN PGP SIGNATURE-----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=B2af
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-5.9-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/drivers
soc/tegra: Changes for v5.9-rc1
This adds missing SoC IDs for Tegra186 and Tegra194 and fixes a typo in
a warning message.
* tag 'tegra-for-5.9-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
soc/tegra: fuse: Fix typo in APB MISC warning
soc/tegra: fuse: Add Tegra186 and Tegra194 SoC IDs
Link: https://lore.kernel.org/r/20200717161300.1661002-4-thierry.reding@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Add core support for the new RZ/G2H (R8A774E1) SoC, including System
Controller (SYSC) and Reset (RST) support.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQ9qaHoIs/1I4cXmEiKwlD9ZEnxcAUCXxFlJQAKCRCKwlD9ZEnx
cBc5AQDuPW0JS4eKE+oARQ3EMxw3ZrEA1zzleiML19YnvEy5YgEA0UsdDlPGnRs1
dZruiWUH9xu4n7zWVZshKf2BBSSTWw0=
=+Zex
-----END PGP SIGNATURE-----
Merge tag 'renesas-drivers-for-v5.9-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into arm/drivers
Renesas driver updates for v5.9
- Add core support for the new RZ/G2H (R8A774E1) SoC, including System
Controller (SYSC) and Reset (RST) support.
* tag 'renesas-drivers-for-v5.9-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel:
soc: renesas: rcar-rst: Add support for RZ/G2H
soc: renesas: Identify RZ/G2H
soc: renesas: Add Renesas R8A774E1 config option
soc: renesas: rcar-sysc: Add r8a774e1 support
clk: renesas: Add r8a774e1 CPG Core Clock Definitions
dt-bindings: power: Add r8a774e1 SYSC power domain definitions
Link: https://lore.kernel.org/r/20200717112427.26032-3-geert+renesas@glider.be
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- assign value to register
- export finalize function and don't call explicitely from flush async
- set specific event
-----BEGIN PGP SIGNATURE-----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=+rna
-----END PGP SIGNATURE-----
Merge tag 'v5.8-next-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux into arm/drivers
add new functions to cmdq helper functions
- assign value to register
- export finalize function and don't call explicitely from flush async
- set specific event
* tag 'v5.8-next-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux:
soc: mediatek: cmdq: add set event function
soc: mediatek: cmdq: export finalize function
soc: mediatek: cmdq: add assign function
Link: https://lore.kernel.org/r/01399fb4-b2d0-e41b-dfd9-f2deba0ef651@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- A couple of fixes on i.MX platform device registration code to stop
the use of invalid IRQ 0.
- Fix a regression seen on ls1021a platform, caused by commit
52102a3ba6 ("soc: imx: move cpu code to drivers/soc/imx").
- Fix a misconfiguration of audio SSI on imx6qdl-gw551x board.
-----BEGIN PGP SIGNATURE-----
iQFIBAABCgAyFiEEFmJXigPl4LoGSz08UFdYWoewfM4FAl8Nxv4UHHNoYXduZ3Vv
QGtlcm5lbC5vcmcACgkQUFdYWoewfM4fIAf/SKUzFbQ/INaU98yW8zONnZVzD/jI
3oTnBP87YJRNiyrLF1lWLs55vfnhum7yXJZXdMbwP55fdJKVaV4StePGz9Sh4Gba
4COHOF3XvF73b4kpcCQEr1U+Y0KHEfMbkwONmerk9ZkRThY2uqcRsdj4br+XA9eU
19ppWdOYZHMjegPu0KuxJlevZJDO6s9I4MCKFWmGgWhanLeGXXd2xtJEgqTWtTnS
EFjOFdBQF+5yd0VY/j6WHBDHWa/fXhDFoAO8Wc5LMCP3VybZdciIi4mN8y0UZoNG
Q5UnBvpYMCqrBwVlyqgeDtJUvYd+33dHqsRbU3KN8yBpRnyHupR9UvcFLA==
=+Gmy
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-5.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes
i.MX fixes for 5.8, round 2:
- A couple of fixes on i.MX platform device registration code to stop
the use of invalid IRQ 0.
- Fix a regression seen on ls1021a platform, caused by commit
52102a3ba6 ("soc: imx: move cpu code to drivers/soc/imx").
- Fix a misconfiguration of audio SSI on imx6qdl-gw551x board.
* tag 'imx-fixes-5.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
soc: imx: check ls1021a
ARM: imx: Remove imx_add_imx_dma() unused irq_err argument
ARM: imx: Provide correct number of resources when registering gpio devices
ARM: dts: imx6qdl-gw551x: fix audio SSI
Link: https://lore.kernel.org/r/20200714145649.GP15718@dragon
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
When using the geni-serial as console, its important to be
able to hit the lowest possible power state in suspend,
even with no_console_suspend.
The only thing that prevents it today on platforms like the sc7180
is the interconnect BW votes, which we certainly don't need when
the system is in suspend. So in the suspend handler mark them as
ACTIVE_ONLY (0x3) and on resume switch them back to the ALWAYS tag (0x7)
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Reviewed-by: Akash Asthana <akashast@codeaurora.org>
Tested-by: Matthias Kaehlcke <mka@chromium.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/1594704709-26072-1-git-send-email-rnayak@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Select ARM_GIC_V3, then it is able to use gic v3 driver in aarch32
mode linux on aarch64 hardware. For aarch64 mode, it not hurts
to select ARM_GIC_V3.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
fsl,ls1021a is a mach under arch/arm/mach-imx/, however it could
not use the soc driver which will break caam on ls1021a platform.
So directly return if it is compatible with fsl,ls1021a.
Fixes: 52102a3ba6 ("soc: imx: move cpu code to drivers/soc/imx")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Tested-by: Horia Geantă <horia.geanta@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The i.MX SCU soc driver depends on SCU firmware driver, so it has to
use platform driver model for proper defer probe operation, since
it has no device binding in DT file, a simple platform device is
created together inside the platform driver. To make it more clean,
we can just move the entire SCU soc driver into imx firmware folder
and initialized by i.MX SCU firmware driver.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The driver provides kernel level API for other drivers
to access the MSM8996 L2 cache registers.
Separating the L2 access code from the PMU driver and
making it public to allow other drivers use it.
The accesses must be separated with a single spinlock,
maintained in this driver.
Signed-off-by: Ilia Lin <ilialin@codeaurora.org>
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Link: https://lore.kernel.org/r/1593766185-16346-2-git-send-email-loic.poulain@linaro.org
Acked-by: Will Deacon <will@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
1. Addition of ARM SMCCC ARCH_SOC_ID support
2. Usage of the custom soc attribute groups already supported in the
infrastucture instead of device_create_file which eliminates the need
for any cleanup when soc is unregistered
3. Minor clean up switching to use standard DEVICE_ATTR_RO() instead of
direct __ATTR
-----BEGIN PGP SIGNATURE-----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=JTXs
-----END PGP SIGNATURE-----
Merge tag 'soc-attr-updates-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into arm/drivers
SoC attributes update for v5.9
1. Addition of ARM SMCCC ARCH_SOC_ID support
2. Usage of the custom soc attribute groups already supported in the
infrastucture instead of device_create_file which eliminates the need
for any cleanup when soc is unregistered
3. Minor clean up switching to use standard DEVICE_ATTR_RO() instead of
direct __ATTR
* tag 'soc-attr-updates-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
firmware: smccc: Add ARCH_SOC_ID support
ARM: OMAP2: Use custom soc attribute group instead of device_create_file
ARM: OMAP2: Switch to use DEVICE_ATTR_RO()
soc: ux500: Use custom soc attribute group instead of device_create_file
soc: ux500: Switch to use DEVICE_ATTR_RO()
soc: integrator: Use custom soc attribute group instead of device_create_file
soc: integrator: Switch to use DEVICE_ATTR_RO()
soc: realview: Use custom soc attribute group instead of device_create_file
soc: realview: Switch to use DEVICE_ATTR_RO()
Link: https://lore.kernel.org/r/20200706165312.40697-1-sudeep.holla@arm.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Commit c31e73121f ("base: soc: Handle custom soc information sysfs
entries") introduced custom soc attribute group in soc_device_attribute
structure but there are no users treewide. While trying to understand
the motivation and tried to use it, it was found lot of existing custom
attributes can moved to use it instead of device_create_file.
Though most of these never remove/cleanup the custom attribute as they
never call soc_device_unregister, using these custom attribute group
eliminate the need for any cleanup as the driver infrastructure will
take care of that.
Let us remove device_create_file and start using the custom attribute
group in soc_device_attribute.
Link: https://lore.kernel.org/r/20200523170859.50003-7-sudeep.holla@arm.com
Cc: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Move device attributes to DEVICE_ATTR_RO() as that would make things
a lot more "obvious" what is happening over the existing __ATTR usage.
Link: https://lore.kernel.org/r/20200523170859.50003-6-sudeep.holla@arm.com
Cc: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Commit c31e73121f ("base: soc: Handle custom soc information sysfs
entries") introduced custom soc attribute group in soc_device_attribute
structure but there are no users treewide. While trying to understand
the motivation and tried to use it, it was found lot of existing custom
attributes can moved to use it instead of device_create_file.
Though most of these never remove/cleanup the custom attribute as they
never call soc_device_unregister, using these custom attribute group
eliminate the need for any cleanup as the driver infrastructure will
take care of that.
Let us remove device_create_file and start using the custom attribute
group in soc_device_attribute.
Link: https://lore.kernel.org/r/20200523170859.50003-5-sudeep.holla@arm.com
Cc: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Move device attributes to DEVICE_ATTR_RO() as that would make things
a lot more "obvious" what is happening over the existing __ATTR usage.
Link: https://lore.kernel.org/r/20200523170859.50003-4-sudeep.holla@arm.com
Cc: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Commit c31e73121f ("base: soc: Handle custom soc information sysfs
entries") introduced custom soc attribute group in soc_device_attribute
structure but there are no users treewide. While trying to understand
the motivation and tried to use it, it was found lot of existing custom
attributes can moved to use it instead of device_create_file.
Though most of these never remove/cleanup the custom attribute as they
never call soc_device_unregister, using these custom attribute group
eliminate the need for any cleanup as the driver infrastructure will
take care of that.
Let us remove device_create_file and start using the custom attribute
group in soc_device_attribute.
Link: https://lore.kernel.org/r/20200523170859.50003-3-sudeep.holla@arm.com
Cc: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Move device attributes to DEVICE_ATTR_RO() as that would make things
a lot more "obvious" what is happening over the existing __ATTR usage.
Link: https://lore.kernel.org/r/20200523170859.50003-2-sudeep.holla@arm.com
Cc: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
The header file linux/uio.h includes crypto/hash.h which pulls in
most of the Crypto API. Since linux/uio.h is used throughout the
kernel this means that every tiny bit of change to the Crypto API
causes the entire kernel to get rebuilt.
This patch fixes this by moving it into lib/iov_iter.c instead
where it is actually used.
This patch also fixes the ifdef to use CRYPTO_HASH instead of just
CRYPTO which does not guarantee the existence of ahash.
Unfortunately a number of drivers were relying on linux/uio.h to
provide access to linux/slab.h. This patch adds inclusions of
linux/slab.h as detected by build failures.
Also skbuff.h was relying on this to provide a declaration for
ahash_request. This patch adds a forward declaration instead.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
The OMAP developers are particularly active at hunting down regressions,
so this is a separate branch with OMAP specific fixes for the v5.8:
As Tony explains
"The recent display subsystem (DSS) related platform data changes
caused display related regressions for suspend and resume. Looks like
I only tested suspend and resume before dropping the legacy platform
data, and forgot to test it after dropping it. Turns out the main issue
was that we no longer have platform code calling pm_runtime_suspend
for DSS like we did for the legacy platform data case, and that fix
is still being discussed on the dri-devel list and will get merged
separately. The DSS related testing exposed a pile other other display
related issues that also need fixing though":
- Fix ti-sysc optional clock handling and reset status checks
for devices that reset automatically in idle like DSS
- Ignore ti-sysc clockactivity bit unless separately requested
to avoid unexpected performance issues
- Init ti-sysc framedonetv_irq to true and disable for am4
- Avoid duplicate DSS reset for legacy mode with dts data
- Remove LCD timings for am4 as they cause warnings now that we're
using generic panels
Other OMAP changes from Tony include:
- Fix omap_prm reset deassert as we still have drivers setting the
pm_runtime_irq_safe() flag
- Flush posted write for ti-sysc enable and disable
- Fix droid4 spi related errors with spi flags
- Fix am335x USB range and a typo for softreset
- Fix dra7 timer nodes for clocks for IPU and DSP
- Drop duplicate mailboxes after mismerge for dra7
- Prevent pocketgeagle header line signal from accidentally setting
micro-SD write protection signal by removing the default mux
- Fix NFSroot flakeyness after resume for duover by switching the
smsc911x gpio interrupt to back to level sensitive
- Fix regression for omap4 clockevent source after recent system
timer changes
- Yet another ethernet regression fix for the "rgmii" vs "rgmii-rxid"
phy-mode
- One patch to convert am3/am4 DT files to use the regular sdhci-omap
driver instead of the old hsmmc driver, this was meant for the
merge window but got lost in the process.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=FFTv
-----END PGP SIGNATURE-----
Merge tag 'arm-omap-fixes-5.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM OMAP fixes from Arnd Bergmann:
"The OMAP developers are particularly active at hunting down
regressions, so this is a separate branch with OMAP specific
fixes for v5.8:
As Tony explains
"The recent display subsystem (DSS) related platform data changes
caused display related regressions for suspend and resume. Looks
like I only tested suspend and resume before dropping the legacy
platform data, and forgot to test it after dropping it. Turns out
the main issue was that we no longer have platform code calling
pm_runtime_suspend for DSS like we did for the legacy platform data
case, and that fix is still being discussed on the dri-devel list
and will get merged separately. The DSS related testing exposed a
pile other other display related issues that also need fixing
though":
- Fix ti-sysc optional clock handling and reset status checks for
devices that reset automatically in idle like DSS
- Ignore ti-sysc clockactivity bit unless separately requested to
avoid unexpected performance issues
- Init ti-sysc framedonetv_irq to true and disable for am4
- Avoid duplicate DSS reset for legacy mode with dts data
- Remove LCD timings for am4 as they cause warnings now that we're
using generic panels
Other OMAP changes from Tony include:
- Fix omap_prm reset deassert as we still have drivers setting the
pm_runtime_irq_safe() flag
- Flush posted write for ti-sysc enable and disable
- Fix droid4 spi related errors with spi flags
- Fix am335x USB range and a typo for softreset
- Fix dra7 timer nodes for clocks for IPU and DSP
- Drop duplicate mailboxes after mismerge for dra7
- Prevent pocketgeagle header line signal from accidentally setting
micro-SD write protection signal by removing the default mux
- Fix NFSroot flakeyness after resume for duover by switching the
smsc911x gpio interrupt to back to level sensitive
- Fix regression for omap4 clockevent source after recent system
timer changes
- Yet another ethernet regression fix for the "rgmii" vs "rgmii-rxid"
phy-mode
- One patch to convert am3/am4 DT files to use the regular sdhci-omap
driver instead of the old hsmmc driver, this was meant for the
merge window but got lost in the process"
* tag 'arm-omap-fixes-5.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (21 commits)
ARM: dts: am5729: beaglebone-ai: fix rgmii phy-mode
ARM: dts: Fix omap4 system timer source clocks
ARM: dts: Fix duovero smsc interrupt for suspend
ARM: dts: am335x-pocketbeagle: Fix mmc0 Write Protect
Revert "bus: ti-sysc: Increase max softreset wait"
ARM: dts: am437x-epos-evm: remove lcd timings
ARM: dts: am437x-gp-evm: remove lcd timings
ARM: dts: am437x-sk-evm: remove lcd timings
ARM: dts: dra7-evm-common: Fix duplicate mailbox nodes
ARM: dts: dra7: Fix timer nodes properly for timer_sys_ck clocks
ARM: dts: Fix am33xx.dtsi ti,sysc-mask wrong softreset flag
ARM: dts: Fix am33xx.dtsi USB ranges length
bus: ti-sysc: Increase max softreset wait
ARM: OMAP2+: Fix legacy mode dss_reset
bus: ti-sysc: Fix uninitialized framedonetv_irq
bus: ti-sysc: Ignore clockactivity unless specified as a quirk
bus: ti-sysc: Use optional clocks on for enable and wait for softreset bit
ARM: dts: omap4-droid4: Fix spi configuration and increase rate
bus: ti-sysc: Flush posted write on enable and disable
soc: ti: omap-prm: use atomic iopoll instead of sleeping one
...
- Fix LDO1 and LDO2 voltage range for a couple of i.MX8M board device
trees.
- Fix i.MX8MP UID fuse offset in i.MX8M SoC driver.
- Fix watchdog configuration in imx6ul-kontron device tree.
- Fix one build warning seen on building soc-imx8m driver with
x86_64-randconfig.
- Add missing put_device() call for a couple of mach-imx PM functions.
-----BEGIN PGP SIGNATURE-----
iQFIBAABCgAyFiEEFmJXigPl4LoGSz08UFdYWoewfM4FAl7zM08UHHNoYXduZ3Vv
QGtlcm5lbC5vcmcACgkQUFdYWoewfM5HNAf+Kw6EPNxYom/MJ4P92gxLAtPA6AO4
+WuLYmSphhgmGAQLFU4UiTH/2sYXmT7fSDwLhfZI5XJp6j8J89Hxe2kyMomvIT92
Xbbzp7fr+2FPGgyI6ImiKTFeSZiT0LPq5fs1uF2lTP6+/SklF9yy5ynUvNULrD4b
iSAXOZkMz6Ft8dn1zYrTKPIYfsTe1zXsDgw8a9sc+0LfgiR5cBTq359jHrN5Q0Tq
NYoOHT+8V5C8BVmzp5I1zoghZEayPT2Ui1JIwBiyVij8KqZvYY3wckjPqgdfQ1vK
IzGksPWRojKAw2RKA59kpUR/pgoZH3GYnfjmCAIOkMnMSgAqz1inZZq2oA==
=iERQ
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes
i.MX fixes for 5.8:
- Fix LDO1 and LDO2 voltage range for a couple of i.MX8M board device
trees.
- Fix i.MX8MP UID fuse offset in i.MX8M SoC driver.
- Fix watchdog configuration in imx6ul-kontron device tree.
- Fix one build warning seen on building soc-imx8m driver with
x86_64-randconfig.
- Add missing put_device() call for a couple of mach-imx PM functions.
* tag 'imx-fixes-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
soc: imx8m: fix build warning
ARM: imx6: add missing put_device() call in imx6q_suspend_init()
ARM: imx5: add missing put_device() call in imx_suspend_alloc_ocram()
soc: imx8m: Correct i.MX8MP UID fuse offset
ARM: dts: imx6ul-kontron: Change WDOG_ANY signal from push-pull to open-drain
ARM: dts: imx6ul-kontron: Move watchdog from Kontron i.MX6UL/ULL board to SoM
arm64: dts: imx8mm-beacon: Fix voltages on LDO1 and LDO2
arm64: dts: imx8mn-ddr4-evk: correct ldo1/ldo2 voltage range
arm64: dts: imx8mm-evk: correct ldo1/ldo2 voltage range
Link: https://lore.kernel.org/r/20200624111725.GA24312@dragon
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The recent display subsystem (DSS) related platform data changes caused
display related regressions for suspend and resume. Looks like I only
tested suspend and resume before dropping the legacy platform data, and
forgot to test it after dropping it. Turns out the main issue was that
we no longer have platform code calling pm_runtime_suspend for DSS like
we did for the legacy platform data case, and that fix is still being
discussed on the dri-devel list and will get merged separately. The DSS
related testing exposed a pile other other display related issues that
also need fixing though:
- Fix ti-sysc optional clock handling and reset status checks
for devices that reset automatically in idle like DSS
- Ignore ti-sysc clockactivity bit unless separately requested
to avoid unexpected performance issues
- Init ti-sysc framedonetv_irq to true and disable for am4
- Avoid duplicate DSS reset for legacy mode with dts data
- Remove LCD timings for am4 as they cause warnings now that we're
using generic panels
Then there is a pile of other fixes not related to the DSS:
- Fix omap_prm reset deassert as we still have drivers setting the
pm_runtime_irq_safe() flag
- Flush posted write for ti-sysc enable and disable
- Fix droid4 spi related errors with spi flags
- Fix am335x USB range and a typo for softreset
- Fix dra7 timer nodes for clocks for IPU and DSP
- Drop duplicate mailboxes after mismerge for dra7
-----BEGIN PGP SIGNATURE-----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=fT9A
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.8/fixes-merge-window-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/fixes
Fixes for omaps for v5.8
The recent display subsystem (DSS) related platform data changes caused
display related regressions for suspend and resume. Looks like I only
tested suspend and resume before dropping the legacy platform data, and
forgot to test it after dropping it. Turns out the main issue was that
we no longer have platform code calling pm_runtime_suspend for DSS like
we did for the legacy platform data case, and that fix is still being
discussed on the dri-devel list and will get merged separately. The DSS
related testing exposed a pile other other display related issues that
also need fixing though:
- Fix ti-sysc optional clock handling and reset status checks
for devices that reset automatically in idle like DSS
- Ignore ti-sysc clockactivity bit unless separately requested
to avoid unexpected performance issues
- Init ti-sysc framedonetv_irq to true and disable for am4
- Avoid duplicate DSS reset for legacy mode with dts data
- Remove LCD timings for am4 as they cause warnings now that we're
using generic panels
Then there is a pile of other fixes not related to the DSS:
- Fix omap_prm reset deassert as we still have drivers setting the
pm_runtime_irq_safe() flag
- Flush posted write for ti-sysc enable and disable
- Fix droid4 spi related errors with spi flags
- Fix am335x USB range and a typo for softreset
- Fix dra7 timer nodes for clocks for IPU and DSP
- Drop duplicate mailboxes after mismerge for dra7
* tag 'omap-for-v5.8/fixes-merge-window-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
Revert "bus: ti-sysc: Increase max softreset wait"
ARM: dts: am437x-epos-evm: remove lcd timings
ARM: dts: am437x-gp-evm: remove lcd timings
ARM: dts: am437x-sk-evm: remove lcd timings
ARM: dts: dra7-evm-common: Fix duplicate mailbox nodes
ARM: dts: dra7: Fix timer nodes properly for timer_sys_ck clocks
ARM: dts: Fix am33xx.dtsi ti,sysc-mask wrong softreset flag
ARM: dts: Fix am33xx.dtsi USB ranges length
bus: ti-sysc: Increase max softreset wait
ARM: OMAP2+: Fix legacy mode dss_reset
bus: ti-sysc: Fix uninitialized framedonetv_irq
bus: ti-sysc: Ignore clockactivity unless specified as a quirk
bus: ti-sysc: Use optional clocks on for enable and wait for softreset bit
ARM: dts: omap4-droid4: Fix spi configuration and increase rate
bus: ti-sysc: Flush posted write on enable and disable
soc: ti: omap-prm: use atomic iopoll instead of sleeping one
Link: https://lore.kernel.org/r/pull-1591889257-410830@atomide.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
QUP core clock is shared among all the SE drivers present on particular
QUP wrapper, the system will reset(unclocked access) if earlycon used after
QUP core clock is put to 0 from other SE drivers before real console comes
up.
As earlycon can't vote for it's QUP core need, to fix this add ICC
support to common/QUP wrapper driver and put vote for QUP core from
probe on behalf of earlycon and remove vote during earlycon exit call.
Signed-off-by: Akash Asthana <akashast@codeaurora.org>
Reported-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/1592908737-7068-3-git-send-email-akashast@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The write_tcs_reg_sync() may be called after timekeeping is suspended
so it's not OK to use ktime. The readl_poll_timeout_atomic() macro
implicitly uses ktime. This was causing a warning at suspend time.
Change to just loop 1000000 times with a delay of 1 us between loops.
This may give a timeout of more than 1 second but never less and is
safe even if timekeeping is suspended.
NOTE: I don't have any actual evidence that we need to loop here.
It's possibly that all we really need to do is just read the value
back to ensure that the pipes are cleaned and the looping/comparing is
totally not needed. I never saw the loop being needed in my tests.
However, the loop shouldn't hurt.
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Maulik Shah <mkshah@codeaurora.org>
Fixes: 91160150ab ("soc: qcom: rpmh-rsc: Timeout after 1 second in write_tcs_reg_sync()")
Reported-by: Maulik Shah <mkshah@codeaurora.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20200528074530.1.Ib86e5b406fe7d16575ae1bb276d650faa144b63c@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Print sensible string instead of just "(null)" for unknown PMIC models.
Also as we are at it, do not let debugfs handler access past pmic_models
array.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20200525164817.2938638-2-dmitry.baryshkov@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Yoshihiro Shimoda