The mrf24j40 has no source to get a permanent extended address. This
patch will add a random generated permanent extended address source.
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Per default mrf24j40 has the channel 11 after reset. This patch adds the
right phy default value for the channel setting.
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds devicetree support to mrf24j40 with proper devicetree
compatible strings.
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch removes spi settings while mrf24j40 probing. These settings
cannot be overwrite while device probing where spi controller should be
already configured. These settings need to be setup by device tree or
platform data.
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The function ieee802154_register_hw should always called at last.
Currently we do hardware init and such things after register hardware
into the subsystem. It could be that the subsystem already call driver
operations while running hardware init.
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch removes the own private dataroom allocation by calling
devm_kzalloc for devrec and assign this pointer to "devrec->hw->priv".
Instead we using like all other drivers ieee802154_alloc_hw and give the
size for the private driver dataroom at the first argument.
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch replaces the spaces after define by a tab.
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds support for edge triggered irq types. We remove the
locking for irq resources by enable/disable irq and allocate directly
some heap buffer at isr. We have still a enable/disable irq path but
this is for level-triggered irq's which need to be disabled until
spi_async clear the irq line.
There is usually a little race condition between "irq line cleared" and
"enable_irq". When in this time a edge triggered irq arrived, we will
not recognize this interrupt. This case can't happend at at86rf230. The
reason is that we unmask TRX_END irq's only which indicates a transmit
or receive completion, which depends on the current state.
On Transmit:
TRX_END arrived and transceiver is in TX_ARET_ON state again, in this
state no other TRX_END can happen until we leave the state.
On Receive:
This is protected with the RX_SAFE_MODE bit which leaves the transceiver
in RX_AACK_BUSY until we readed the framebuffer. In this state no other
TRX_END can happen.
Tested with RPi where I first detected issues between edge/level irq's.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Alexander Aring <alex.aring@gmail.com>
Cc: Stefan Schmidt <stefan@osg.samsung.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch supports handling for printout different chipnames between
atusb and rzusb. The rzusb contains an at86rf230 and atusb an at86rf231
transceiver.
Cc: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch introduce a more detailed information why edge triggered
irq's are currently not recommended. It could be that rising/falling
edge detection can happen while the irq is disabled.
Suggested-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch introduce debugfs support for collect trac status stats. To
clear the stats ifdown the interface of at86rf230 and start the
interface again.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
To abort a TX_ARET_BUSY state it's recommended to switch into TRX_OFF
state by doing STATE_TRX_FORCE_OFF. This patch will do always a TRX_OFF
state change when the transceiver stucks in any state. From TRX_OFF we
can switch to the states which are also possible by TX_ON state.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When transmit is done, indicated by trx_end irq, we do first a force
state change to TX_ON and then checking the trac status, if the trac
status is unequal zero we do a state change to TRX_OFF.
This patch changes to the following behaviour, we first check on trac
status after trx_end occurs and then doing a normal change to TX_ON
without do the state change to TRX_OFF when trac status is unequal zero.
The reasons are that the datasheet doesn't described when the trac
status register is cleared, we should doing to evaluate the trac status
at first. The reason to remove the TRX_OFF change if the trac status is
unequal to zero and it was force is the following paragraph inside The
at86rf2xx datasheets:
"Using FORCE_PLL_ON to interrupt an TX_ARET transaction, it is
recommended to check register bits [7:5] of register address 0x32 for
value 0. If this value is different, TRX_CMD sequence FORCE_TRX_OFF shall
be used immediately followed by TRX_CMD sequence PLL_ON. This performs a
state transition to PLL_ON."
The meaning is here "to interrupt an TX_ARET transaction" in case of
trx_end interrupt the "TX_ARET transaction" is already done and we don't
interrupt the "TX_ARET transaction" by doing the change to TX_ON (PLL_ON)
here. Additional I changed the force change to normal TX_ON which seems to
work here.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When the device tree support is disabled, the fifo_pin is uninitialized,
this patch will set the fifo_pin value based on platform data
Signed-off-by: Yong Li <sdliyong@gmail.com>
Acked-by: Varka Bhadram <varkabhadram@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch changes the state change behaviour of at86rf230 to always
TX_ARET mode. According the at86rf2xx datasheets TX_ARET mode doesn't
mean to be always waiting for ack frames after transmit. The transceiver
will automatically wait for ack frames or not if the acknowledge request
bit is set. See section "TX_ARET_ON – Transmit with Automatic Frame
Retransmission and CSMA-CA Retry".
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
According Documentation/timers/timers-howto.txt the usually case for
setting up a hrtimer takes > ~10us. So we should use udelay in this
case so we are sure that the state change was done, before doing the
state change assert.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In ancient times it was necessary to manually initialize the bus
field of an spi_driver to spi_bus_type. These days this is done in
spi_register_driver(), so we can drop the manual assignment.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Acked-by: Varka Bhadram <varkabhadram@gmail.com>
Acked-by: Alan Ott <alan@signal11.us>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This code cleanups the start and stop callbacks by removing hw->priv and
using the already dereferenced variable lp which is the same.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds support for a new random csma backoffs settings when
going into sleep state. This is recommended according at86rf2xx
datasheets.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
While in sleep state then we can't access the at86rf2xx registers. This
patch checks if the transceiver is in sleep state before sending spi
messages via regmap. Regmap is used on every driver ops callback except
for receive and xmit handling, but while receive and xmit handling the
phy should not be inside the sleep state.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds a suspended testcase into the xmit_async functionality.
In the hope that we can found race conditions when xmit_async is called
after an ieee802154_ops stop. This should never happen.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds support for sleep state when between stop and start
period. In this period the transceiver isn't used by the subsystem, in
this time we disable the irq and going into the sleep state.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch use high level interrupt type as fallback handling when no
irq type is given.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
neither ram nor register write return values have been checked here.
Checking both now. Assign ret with 0 as all other assignments are inside
if blocks and might not happen before we return ret.
CID: 1230469
Signed-off-by: Stefan Schmidt <stefan@osg.samsung.com>
Acked-by: Varka Bhadram <varkabhadram@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If we run into an error during rx we set the the error code in ret, but override
it afterwards. Using a different variable for the extra case avoids this
situation.
CID: 1226982, 1226983
Signed-off-by: Stefan Schmidt <stefan@osg.samsung.com>
Cc: Alan Ott <alan@signal11.us>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch removes the hardware auto acknowdledge flag which indicates
that the transceiver supports this handling. This flag is never
evaluated inside mac802154 and all transceivers should support this
handling by default per hardware.
Suggested-by: Lennert Buytenhek <buytenh@wantstofly.org>
Cc: Alan Ott <alan@signal11.us>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Reviewed-by: Varka Bhadram <varkabhadram@gmail.com>
Acked-by: Stefan Schmidt <stefan@osg.samsung.com>
Acked-by: Varka Bhadram <varkabhadram@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch removes the virtual interface structure from sub if data
struct, because it isn't used anywhere. This structure could be useful
for give per interface information at softmac driver layer. Nevertheless
there exist no use case currently and it contains the interface type
information currently. This information is also stored inside wpan dev
which is now used to check on the wpan dev interface type.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Reviewed-by: Varka Bhadram <varkabhadram@gmail.com>
Acked-by: Varka Bhadram <varkabhadram@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch updates the current channel to 11. This is the default
value on reset.
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
CC2520 has the default 0dBm transmit power level on reset.
This patch update initial value of transmit power with 0dBm value.
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Cc: Brad Campbell <bradjc5@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds support for seeting tx power values for cc2520
and also for the combination of CC2520-CC2591.
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Cc: Brad Campbell <bradjc5@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch changes tha way of handling of cc2591-cc2520 combination
by moving amplified variable from platform data to private data.
This will be useful in other sections like tx power support.
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Cc: Brad Campbell <bradjc5@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Initially we dont have the tx power settings from the user-space.
Now we have the support for seeting the tx power level.
So lets use the default tx power setting for the radio.
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Cc: Brad Campbell <bradjc5@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Atusb uses the at86rf231 transceiver so we can use the same calculation
for txpower settings for it.
Signed-off-by: Stefan Schmidt <stefan@osg.samsung.com>
Reviewed-by: Varka Bhadram <varkabhadram@gmail.com>
Acked-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
With this function we can set individual bits in the registers if needed.
With the old SR_VALUE macro we could only set one bit in the register
which was ok for some scenarios but not for all. With this subreg write
function we can now set more bits defined by the mask while not touching
the rest.
We start using it for the current SR_VALUE use case and will use it more
in upcoming patches.
Signed-off-by: Stefan Schmidt <stefan@osg.samsung.com>
Reviewed-by: Varka Bhadram <varkabhadram@gmail.com>
Acked-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds support for the at86rf230 version check which is used
by the rzusb stick.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Since firmware version 0.2 we use AACK handling directly in the firmware.
Inform the stack that the hardware supports and uses it.
Signed-off-by: Stefan Schmidt <stefan@osg.samsung.com>
Acked-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Together with mainlining the driver we released a first public binary version
of the device firmware. This is version 0.2. With this change we warn users
who run outdated versions of the firmware. While we have not seen problems
with it yet (thus no error, but a warning only) it would be better to run the
released and tested firmware. You can find released versions here:
http://downloads.qi-hardware.com/people/werner/wpan/web/
Signed-off-by: Stefan Schmidt <stefan@osg.samsung.com>
Acked-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch add missing values for at86rf212 ed level values. Currently
there are 15 values and the register setting supports 16 different ed
level values.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Reported-by: Craig Younkins <craig@freshtemp.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch just cleanups the code at several places.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch will add async xmit support for the fakelb driver.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch cleanups the fakelb_hw_deliver function by removing them.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds reset defaults for the fakelb phy. I used the channel 13
and page 0 which is the same default like at86rf233.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds an own phy attribute for page and channel into
fakelb_phy. The current way is to use the internal mac802154 stored phy
pib values which can occur in locking issues while using it inside the
driver layer.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch introduce a fakelb ifup phys list, which stores all
registered phys which are in an operated mode. This will reduce the
iterations of non-operated phys while transmit frames. There exists two
locks now, one rwlock for the operated interfaces and the spinlock for
protecting the list for all registered virtual phys.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The list need to be protected while iteration which is need when other
list iterates at the same time over this list.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch moves the fakelb list of all registered phy's in a static
declaration in the fakelb driver.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch moves the rwlock declarition into a static variable.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
A real phy don't transmit the transmitted frame back to the phy. This
behaviour will confuse the 6LoWPAN and the upper IPv6 neighbour
discovery cache. We need now at least two virtual phy's to creating a
virtual wpan network.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch renames fakelb_dev_priv to fakelb_phy. We don't faking
devices here, we fake wpan phys. This avoids also confusing with the
variable priv, which is used several times in this driver to represent
this structure.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Iterate and removing items from a list, we should use
list_for_each_entry_safe instead list_for_each_entry to avoid accidents
by removing.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch change the default virtual wpan phys of fakelb driver from
one to two. To have one virtual phy makes no sense, because it need at
least two virtual phy's to speak to each other.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds support for the atusb transceiver.
The current driver supports basic functionality only. Possible further
tasks would be to sync functionality with the at86rf230 driver, because
the atusb use internally an at86rf231 transceiver. Some of these
features need a firmware update like AACK and ARET handling.
I did small changes to this driver to work with xmit_async callback and
setting of a random extended perm address.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Cc: Werner Almesberger <werner@almesberger.net>
Cc: Stefan Schmidt <s.schmidt@samsung.com>
Cc: Richard Sharpe <realrichardsharpe@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch fix the complete callback for going into aret on. Currently
we starting after a state change into aret on again a state change into
aret on which is not necessary.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
fakelb_hw_deliver creates a copy of the skb's header which can
potentially return NULL so we now check for this before actually
delivering to the 802.15.4 MAC layer.
Signed-off-by: Martin Townsend <martin.townsend@xsilon.com>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds the reset states for tx power levels after running reset
procedure.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds reset values for cca ed level values after running reset
procedure.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch reworks the cca energy detection level handling. This
contains a calculation which works on all transceiver types and
add support for dump cca energy detection levels.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds support for get transmit power levels and reworks the
set of transmit power levels which was broken before.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch sets the at86rf230 supported cca modes. In case of at86rf212
it also can support listen before transmit.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch introduce a flag property for the wpan phy structure.
The current flag settings in ieee802154_hw are accessable in mac802154
layer only which is okay for flags which indicates MAC handling which
are done by phy. For real PHY layer settings like cca mode, transmit
power, cca energy detection level.
The difference between these flags are that the MAC handling flags are
only handled in mac802154/HardMac layer e.g. on an interface up. The phy
settings are direct netlink calls from nl802154 into the driver layer
and the nl802154 need to have a chance to check if the driver supports
this handling before sending to the next layer.
We also check now on PHY flags while dumping and setting pib attributes.
In comparing with MIB attributes the 802.15.4 gives us an default value
which we assume when a transceiver implement less functionality. In case
of MIB settings the nl802154 layer doesn't need to check on the
ieee802154_hw flags then.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch introduce the wpan_phy_supported struct for wpan_phy. There
is currently no way to check if a transceiver can handle IEEE 802.15.4
complaint values. With this struct we can check before if the
transceiver supports these values before sending to driver layer.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Suggested-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Acked-by: Varka Bhadram <varkabhadram@gmail.com>
Cc: Alan Ott <alan@signal11.us>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch change the handling of cca energy detection level from dbm to
mbm. This prepares to handle floating point cca energy detection levels
values. The old netlink 802.15.4 will convert the dbm value to mbm for
handling backward compatibility.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch change the handling of transmit power level from dbm to mbm.
This prepares to handle floating point transmit power levels values. The
old netlink 802.15.4 will convert the dbm value to mbm for handling
backward compatibility.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch change the transmit power from s8 to s32. This prepares to store a
mbm value instead dbm inside the transmit power variable. The old
interface keep the a s8 dbm value, which should be backward compatibility
when assign s8 to s32.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds support for one of the slp_tr gpio use cases which
indicates the TX_START command without doing some spi bus traffic.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Reviewed-by: Varka Bhadram <varkabhadram@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If a transmit ends in a calibration which means the transceiver do a
TRX_OFF state change, we can directly change into TX_ARET state instead
doing a TX_ON to TX_ARET statechange.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Reviewed-by: Varka Bhadram <varkabhadram@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
All supported transceivers can do a valid state change from TRX_OFF to
AACK_ON. This patch removes the state change chain from TRX_OFF ->
TX_ON -> AACK_ON instead we doing a directly state change from TRX_OFF
to AACK_ON.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds a calibration timeout reset when change from TRX_OFF to
TX_ARET_ON which also occurs a calibration.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Reviewed-by: Varka Bhadram <varkabhadram@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch moves the calculation timeout of TRX_OFF to RX_AACK_ON
handling to the async state change functionality. With this patch we can
do a reset of calculation timeout when others TRX_OFF to RX_AACK_ON
happens instead of doing this on interface up only.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Reviewed-by: Varka Bhadram <varkabhadram@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch cleanups the at86rf230 driver to use a space instead a tab
after define.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Reviewed-by: Varka Bhadram <varkabhadram@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Instead of using the 'magic' number of 0x1f the TRX_STATE_MASK macro is
introduced.
Signed-off-by: Christoffer Holmstedt <christoffer.holmstedt@gmail.com>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Netlink attribute for the power is s8. But for the driver level
operations we are collection power level value into integer.
It has to be change to s8 from int.
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Acked-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch fix the error handling when is_tx is true. The error handling
tries to get the transceiver into RX_AACK_ON mode then we need to be
sure that is_tx is false.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This spinlock isn't necessary because if we are in TX_ON/TX_ARET_ON
state the transceiver can't be interrupted e.g. by receiving a frame
when a SHR was detected. In this time the transceiver doesn't leave
the TX_ON/TX_ARET_ON state until the tx complete irq change the state
into RX_AACK_ON again. This means a receiving interrupt in state
TX_ON/TX_ARET_ON can't happen and is_tx is protected by transceiver.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The TI CC2521 is an RF power amplifier that is designed to interface
with the CC2520. Conveniently, it directly interfaces with the CC2520
and does not require any pins to be connected to a
microcontroller/processor. Adding a CC2591 increases the CC2520's range,
which is useful for border router and other wall-powered applications.
Using the CC2591 with the CC2520 requires configuring the CC2520 GPIOs
that are connected to the CC2591 to correctly set the CC2591 into TX and
RX modes. Further, TI recommends that the CC2520_TXPOWER and
CC2520_AGCCTRL1 registers are set differently to maximize the CC2591's
performance. These settings are covered in TI Application Note AN065.
This patch adds an optional `amplified` field to the cc2520 entry in the
device tree. If present, the CC2520 will be configured to operate with a
CC2591.
The expected pin mapping is:
CC2520 GPIO0 --> CC2591 EN
CC2520 GPIO5 --> CC2591 PAEN
Signed-off-by: Brad Campbell <bradjc5@gmail.com>
Acked-by: Varka Bhadram <varkabhadram@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Storing the `platform_data` struct inside of the SPI struct when using
the device tree allows for a later function to edit the content of that
struct. This patch refactors the `cc2520_get_platformat_data` function
to accept a pointer to a `cc2520_platform_data` struct and populates
the fields inside of it.
This change mirrors commit aaa1c4d226
("at86rf230: copy pdata to driver allocated space").
Signed-off-by: Brad Campbell <bradjc5@gmail.com>
Acked-by: Varka Bhadram <varkabhadram@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch fix an issue when at86rf230_read_subreg was successful. The
function at86rf230_read_subreg will directly call regmap_read which
returns zero on successful. Nobody figured out issues yet because it was
only necessary to evaluate dvdd state while probing. This could make
trouble because the stack variable could have an random value.
The function is also used by reset the irq line before requesting irq, but
the value isn't evaluated afterwards.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
These registers are also changed by transceiver and should be volatile
for right accessing via regmap debugfs.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds a handling for calibration if we are 5 minutes in PLL
state. I first tried to implement the calibration functionality in
TX_ON state via register values CF_START and DCU_START, but this occurs
a one second delay at each calibration time.
An another solution to start a calibration is to switch from TRX_OFF
state into TX_ON, then a calibration is done automatically by
transceiver. This method will be used in this patch, after each transmit
of a frame we check with jiffies if the PLL is set 5 minutes without
doing a TRX_OFF->(TX_ON || RX_AACK_ON) or channel switch. The worst case
would be a transceiver in receiving mode only, but this is under normal
operation very unlikely.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Cc: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Cc: Werner Almesberger <werner@almesberger.net>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch replace the state change timing relevant sleeps with
hrtimers. Currently the sleeps are done in the complete handler of
spi_async. The relation of doing the state change timing sleep with a
timer will get the sleep functionality out of spi_async complete handler
context.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch initialize xtal_trim value to zero. The xtal_trim property is
an optional device tree value. Currently if no xtal_trim property is
given the xtal_trim value can be contain random data, because it's a
stack variable. This patch init the xtal_trim value to zero which is
also the default value after reset for at86rf230 transceivers.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In the most cases the spi messages has a length of two. Currently we
always set the the len field to two before transmit a spi message. In
cases for read out/write in the frame buffer we need another len. This
patch use trx len two as default. For the frame buffer cases we restore
the trx len to two on success and failure. This will reduce the len
setting of two when it's already two.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch cleanups the referencing for the state change context
variable. The state change context should only set once and this is by
initial a state change. This patch will use the initial state change
variable in the complete handler of the state change by using the ctx
context which should be always the same like the initial state change
context.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
By holding the irq variable inside at86rf230_state_change we can squash
some multiple dereferencing for getting irq num.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch refactor the receive handling into one function.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
I had this variable because I thought it would be protected by
disable/enable irq but this is not true. It's protected by stop/wake
netdev queue which is called by ieee802154_xmit_complete.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch introduce a transmit retry handling into at86rf230 transmit
path. Current behaviour is to wait the normal receive time if we want
to go into STATE_TX_ON when the transceiver is in STATE_BUSY_RX_AACK
which indicates that a frame is currently receiving. A non force state
change will not interrupt the the receiving state.
The current behaviour is that after the normal receive time we will
start a force change into STATE_TX_ON. With this patch we do seven
retries to go into STATE_TX_ON without forcing. After we hit the
AT86RF2XX_MAX_TX_RETRIES we will start the force state change.
This is a polling like method to go into STATE_TX_ON in times of maximum
receiving time.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
While testing I experience a deadlock while using the at86rf233 on a
raspberry pi. The reason was an edge triggered gpio irq because the irq
triggered while irq was disabled. This issue doesn't happend on a level
triggered irq because the irq will hit after calling enable_irq.
This patch adds a warning that it's not recommended to use a edge-triggered
irq type. Also change the examples to high-level irqtype.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The at86rf2xx chips supports the setting of irq polarity if active low
or active high. This patch adds a handling for IRQ_ACTIVE_LOW if the
irq_type is IRQ_TYPE_LEVEL_LOW.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Since we support at86rf233 we need to ensure that basic operation
default values are the same. This patch always sets IRQ_MASK_MODE to 0
which is after reset 1 at the at86rf233 and 0 at the at86rf231.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch removes tx_timeout handling. We used it in sync xmit
handling. Since we support async xmit handling a xmit timeout handling
isn't easy to implement and should be implemented by netdev watchdog
mechanism.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds support for setting the xtal trim register. Some at86rf2xx
transceiver boards needs fine tuning the xtal capacitor.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch copies the platform data in driver allocated space at first.
With this change we ensure that we access the allocated platform data as
readonly space.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Reported-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
return type of wait_for_completion_timeout is unsigned long not int.
As rc is used here only for wait_for_completion_timeout the type is simply
changed to unsigned long.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch removes the warnings (space before , ) shown by
checkpatch.pl
Signed-off-by: Mohammad Jamal <md.jamalmohiuddin@gmail.com>
Acked-by: Varka Bhadram <varkabhadram@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch replaces the shifting operations by BIT macro
Signed-off-by: Mohammad Jamal <md.jamalmohiuddin@gmail.com>
Acked-by: Varka Bhadram <varkabhadram@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The regmap_config struct may be const because it is not modified by the
driver and regmap_init() accepts pointer to const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It will remove the bug of havine zero perm_extended_addr address.
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If allocation of memory fails instead of going to ret goto label
and returning from there, we can directly return -ENOMEM on failure.
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Since commit ab78029ecc (drivers/pinctrl: grab default handles from device
core), we can rely on device core for setting the default pins.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Varka Bhadram <varkabhadram@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This version check allows the driver to only work with v=1 hardware
however there is no driver-facing difference with newer versions
(confirmed by Atmel FAEs) so this check needlessly prevents the driver
from being used with radios now in production.
Tested on AT86RF212B radio (which came up as v=3).
Signed-off-by: Andrey Yurovsky <yurovsky@gmail.com>
Reviewed-by: Stefan Schmidt <s.schmidt@samsung.com>
Acked-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The driver was reading the PART_NUM register for both the part number
(type of device) and the part version, the version is actually in
register 0x1D, VERSION_NUM. I believe that this was a copy-paste error.
Tested on AT86RF212B where the part is detected to be the expected part
number (0x07) and version (0x03 on mine).
Signed-off-by: Andrey Yurovsky <andrey@snupi.com>
Acked-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The attribute extra_tx_headroom should already be zero.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Reviewed-by: Stefan Schmidt <s.schmidt@samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch changes the context pointer to the parameter given one inside
function at86rf230_async_state_change_start. This could occur problem if
context isn't pointed to lp->state.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Reviewed-by: Stefan Schmidt <s.schmidt@samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch makes the at86rf230_async_error inline. This function is
small enough to handle inline.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Reviewed-by: Stefan Schmidt <s.schmidt@samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch removes an unnecessary if branch inside the tx complete
handler.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Reviewed-by: Stefan Schmidt <s.schmidt@samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
CC: Alan Ott <alan@signal11.us>
Signed-off-by: Stefan Schmidt <s.schmidt@samsung.com>
Acked-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
CC: Alan Ott <alan@signal11.us>
Signed-off-by: Stefan Schmidt <s.schmidt@samsung.com>
Acked-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds the default cca setting after device reset for at86rf230
driver.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The current cca setting handle is a driver specific call. We need to
introduce some 802.15.4 specific layer and mapping 802.15.4 cca modes to
driver specific ones inside the 802.15.4 driver. This patch will add
such 802.15.4 layer and mapping the cca settings to driver specific ones.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes, just
removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There are
some ath9k patches coming in through this tree that have been acked by
the wireless maintainers as they relied on the debugfs changes.
Everything has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOD20ACgkQMUfUDdst+ylLPACg2QrW1oHhdTMT9WI8jihlHVRM
53kAoLeteByQ3iVwWurwwseRPiWa8+MI
=OVRS
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
This patch fix an copy&paste issue in the comment of setting symbol
duration. These comments are more correct according the at86rf212 datasheet
now.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch removes the interframe spacing time workaround from at86rf230
driver and use the mac802154 one. The interframe spacing time differs at
at86rf212 and channel setting. This patch fix this handling which is also
a new workaround and should be moved into mac802154 while channel
setting.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds a new interframe spacing time handling into mac802154
layer. Interframe spacing time is a time period between each transmit.
This patch adds a high resolution timer into mac802154 and starts on
xmit complete with corresponding interframe spacing expire time if
ifs_handling is true. We make it variable because it depends if
interframe spacing time is handled by transceiver or mac802154. At the
timer complete function we wake the netdev queue again. This avoids
new frame transmit in range of interframe spacing time.
For synced driver we add no handling of interframe spacing time. This
is currently a lack of support in all synced xmit drivers. I suppose
it's working because the latency of workqueue which is needed to call
spi_sync.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch removes the invalid max frame retries check from driver
layer. This is already handled by nl802154 framework. Also the IEEE
802.15.4 standard doesn't allow a frame retries setting above 7. This
seems to be valid for the at86rf230 transceiver but the chip running out
of spec then. We only allow settings according 802.15.4 right now.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch removes the invalid check on max csma backoffs in driver
layer. This is already handled by nl802154 framework.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch removes the invalid backoff exponent check from driver layer.
This is already handled by nl802154.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch removes validation of page and channel while setting from
driver layer. This is already handled by nl802154 and mac802154.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
drivers/net/ieee802154/at86rf230.c:1365:1-3: WARNING: end returns can be simpified
Simplify a trivial if-return sequence. Possibly combine with a
preceding function call.
Generated by: scripts/coccinelle/misc/simple_return.cocci
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Acked-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds a force setting of slotted operation bit. The atben
chips sometimes set these bit. The reason is unknown. Nevertheless we
don't support slotted operation so we set this bit now force while
probing.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds support for a random generated perm extended address for
the at86rf230 driver.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds an ieee802154_vif similar like the ieee80211_vif which
holds the interface type and maybe further more attributes like the
ieee80211_vif structure.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Cc: Varka Bhadram <varkabhadram@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch sets the reset state channels accoridng at86rf2xx datasheets.
We don't need to set the default page here which is zero on all chips.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Since commit e37d2ec82a ("mac802154: ops:
declare channel and page as u8") the page parameter can't be below zero.
This patch fix a kbuild test robot warning. Furthermore this check
should be removed and handled by netlink 802.15.4 interface.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch indicates that the at86rf230 driver deliver with checksum
instead drop the crc before delivering.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds support for promiscuous mode setting for the at86rf230
driver.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Overdue introduction for address filtering hardware flag. Furthermore we
will check and set address filtering on interface up. This patch
prepares that we can check if an transceiver supports address filtering
option. Currently all mainline driver supports hardware address filtering.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Cc: Alan Ott <alan@signal11.us>
Cc: Varka Bhadram <varkabhadram@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds a new IEEE802154_HW_ARET hardware flag for indicating
that the transceiver supports ARET handling. Also remove the
IEEE802154_HW_FRAME_RETRIES from IEEE802154_HW_CSMA flag. Frame retries
handling is part of ARET.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch removes all might_sleep calls from driver layer. This
handling is already done by mac802154 layer.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The range of channel and page fits into an unsigned byte range. This
patch changes the set_channel parameter definitions for channel and
page to u8.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Cc: Alan Ott <alan@signal11.us>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The ieee802154_ops structure should be never changed during runtime.
This patch declare this structure as const to avoid a runtime change.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Cc: Alan Ott <alan@signal11.us>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Current behaviour it to copy the frame inclusive CRC into a skb, then
remove the CRC from the skb. This patch optimizes this by not copying
the CRC at the first place.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds the ieee802154_is_valid_psdu_len function to validate
the psdu length. If the psdu length is invalid we use the maximum
payload to receive also corrupted frames in monitor mode.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch change the allocation of skb inside the ieee802154 driver
layer to dev_alloc_skb. This changes also the gfp mask to GFP_ATOMIC
which is needed for upcomming change that the receiving is done by a
tasklet and not a workqueue anymore.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Cc: Alan Ott <alan@signal11.us>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch converts the sync xmit handling into an async xmit handling. The
driver was already prepared for this step, all other drivers need more
work to implement a xmit_async function.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch renames the existsing xmit callback to xmit_sync and
introduces an asynchronous xmit_async function. If ieee802154_ops
doesn't provide the xmit_async callback, then we have a fallback to
the xmit_sync callback.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Cc: Alan Ott <alan@signal11.us>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The identical struct of the wireless stack implementation is named
ieee80211_hw. This is useful to name the variable hw instead of get
confusing with netdev dev variable.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Cc: Alan Ott <alan@signal11.us>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch removes the not functional fakehard driver. We don't support
HardMAC 802.15.4 drivers right now.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch moves the ieee802154 header into include/linux instead
include/net. Similar like wireless which have the ieee80211 header
inside of include/linux.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Cc: Alan Ott <alan@signal11.us>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The wpan-phy header contains the wpan_phy struct information. Later this
header will be have similar function like cfg80211 header. The cfg80211
header contains the wiphy struct which is identically the wpan_phy
struct inside 802.15.4 subsystem.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Cc: Alan Ott <alan@signal11.us>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch fixs a typo in address filter defines from IEEE802515 to
IEEE802154.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Cc: Alan Ott <alan@signal11.us>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch removes the FSF address in files which belongs to ieee802154
and mac802154.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Cc: Alan Ott <alan@signal11.us>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The async error function will already printout the errno over dev_err.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Sometimes the async state function is call in an context where the spi
irq is diabled. This patch fix the handling to enable the irq when
spi_async failed in the async state change calling chain. We do this by
a context parameter irq_enable and evaluate this parameter when
spi_async failed instead of returning spi_async errno.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When the driver waits for a tx completion currently the driver direct
enables the irq. When we switching to RX_AACK_ON some steps afterwards
the driver could receive a new frame and request resources which are
already in use, for example irq state change resource.
To be sure there are no new interrupts when we switching to RX_AACK_ON,
we enable the irq when state change to RX_AACK_ON was completed.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds a missing enable_irq when spi_async in isr failed.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch removes dereferencing irq number over spi struct. Instead we
doing it directly over isr paramater.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds lifs/sifs handling only if max_frame_retries is above
zero. The at86rf2xx datasheets says nothing about phy lifs/sifs
handling. I asked the atmel support and they said lifs/sifs is done
by phy when max_frame_retries is above zero.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds an async error handling function if sync state change
runs into a timeout. The async error handling function tries to recover
the phy state machine into a valid state.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The rc variable is zero if we get a timeout. Instead of pass the rc
variable to the async error handling function which try to recover the
phy, we use a static -ETIMEDOUT errno.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The MRF24J40MC module has an external amplifier which should be
enabled. The TX power has to be lowered to meet FCC regs.
Signed-off-by: Simon Vincent <simon.vincent@xsilon.com>
Acked-by: Alan Ott <alan@signal11.us>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Remove the return statement in the void function.
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Acked-by: Alan Ott <alan@signal11.us>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch removes the current synchron state change function and add a
new function for a state assert. Change the start and stop callbacks to
use this new synchron state change behaviour. It's a wrapper around the
async state change function.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch rework the irq_pol register setting for rising and falling
interrupt settings only. The default behaviour should be rising flag.
Also use IRQ_TYPE_* defines instead of IRQF_* defines. There is no
functionality change but irq_get_trigger_type returns IRQ_TYPE_* defines.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to set this bit in start callback which could be
called more than once.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is a complete reimplementation of transmit and receive
handling for the at86rf230 driver.
It solves also six bugs:
First:
The RX_SAFE_MODE is enabled and the transceiver doesn't leave the
receive state while the framebuffer isn't read by a CMD_FB command.
This is useful to read out the frame and don't get into another receive
or transmit state, otherwise the frame would be overwritten.
The current driver do twice CMD_FB calls, the first one leaves this
protection.
Second:
Sometimes the CRC calculation is correct and the length field is greater
127. The current mac802154 layer and filter of a at86rf2xx doesn't check
on this and the kernel crashes. In this case the frame is corrupted, we
send the whole receive buffer to the next layer which can be useful for
sniffing.
Thrid:
There is a undocumented race condition. When we are go into the
RX_AACK_ON state the transceiver could be changed into RX_AACK_BUSY
state. This is a normal behaviour. In this case the transceiver received
a SHR while assert wasn't finished.
Fourth:
It also handle some more "correct" state changes. In aret mode the
transceiver need to go to TX_ON before the transceiver go into
RX_AACK_ON.
Fifth:
The programming model [0] describes also a error handling in ARET mode
if the trac status is different than zero. This is patch adds support
for handling this.
Sixth:
In receive handling the transceiver should also get the trac status
according [0]. The driver could use the trac status as error statistic
handling, but the driver doesn't use this currently. There is maybe some
timing behaviour or the read of this register change some transceiver
states.
In addition the irqworker is removed. Instead we do async spi calls and
no scheduling is involved anymore. The transmit function is also
asynchron but with a wait_for_completion handling. The mac802154 layer
doesn't support asynchron transmit handling right now.
The state change behaviour is now changes, before it was:
1. assert while(!STATE_TRANSITION_IN_PROGRESS)
2. state change
3. assert while(!STATE_TRANSITION_IN_PROGRESS)
4. assert once(wanted state != current state)
Sometimes a unexcepted state change occurs when 4. assert was violated.
The new state change behaviour is:
1. assert while(!STATE_TRANSITION_IN_PROGRESS)
2. state change
3. wait state change timing according datasheet
4. assert once(wanted state != current state)
This behaviour is described in the at86rf231 software programming model [0].
The state change documentation in this programming guide should also valid for
at86rf212 and at86rf233 chips.
The transceiver don't do a FORCE_TX_ON while we want to transmit a PDU.
The new behaviour is a TX_ON and wait a receiving time (tFrame + tPAck).
If we are still in RX_AACK_BUSY then we transmit a FORCE_TX_ON as timeout
handling. The different is that FORCE_TX_ON aborts receiving and TX_ON
waits if RX_AACK_BUSY is finished. This should decrease the drop rate of
packets.
[0] http://www.atmel.com/Images/AVR2022_swpm231-2.0.zip
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To set the CCA_ED_THRES register the calculation for at86rf23x is
different than for at86rf212. This patch adds a new callback for this
calculation in chip data struct.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a new at86rf2xx_chip_data structure which holds device
specific attributes. Instead of runtime decisions "if (is212())" we set
callbacks/attributes while device detection.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch drops the current lowlevel spi calls for the detect device
function instead we handle this via regmap. Also put the detection of
in a seperate function and set all device specific attributes while detection.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds regmap support for the at86rf230 driver and drop the
lowlevel spi access functions and use the regmap access functions.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds new mac802154 hw flags for transmit power, csma and
listen before transmit (lbt). These flags indicates that the transceiver
supports these features. If the flags are set and the driver doesn't
implement the necessary functions, then ieee802154_register_device
returns -ENOSYS "Function not implemented".
This patch merges also all at86rf230 operations into one operations structure
and set the right hw flags for the at86rf230 transceivers.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the driver support for the cc2520 radio.
Driver support:
- Tx and Rx of IEEE-802.15.4 packets
- Energy Detection on channel
- Setting the Channel for the radio. [b/w 11 - 26 channels]
- Start and Stop the radio
- h/w address filtering
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 8eba0eefae ("at86rf230: remove irq_type in
request_irq") removed the trigger configuration when requesting an irq,
and instead relied on the interrupt trigger to be properly configured
already. This does not seem to be an assumption that can be safely made,
since boards disable all interrupt triggers on boot.
On these boards, force the irq to trigger on rising edge, which is also
the default for the chip.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
separate the mrf24j40 hardware initialisation from probe()
and adds the sanity checkings.
These checkings are required if somebody hasn't a right spi configuration
the probe function should fail. So we have to return from there.
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: David S. Miller <davem@davemloft.net>
adds the device managed APIs so that no need worry about
freeing the resources.
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves data allocated using kzalloc to managed data allocated
using devm_kzalloc and cleans now unnecessary kfrees in probe and remove
functions. An explicit linux/device.h include is added to make sure
the devm_*() routine declarations are unambiguously available.
The following Coccinelle semantic patch was used for making the change:
@platform@
identifier p, probefn, removefn;
@@
struct platform_driver p = {
.probe = probefn,
.remove = removefn,
};
@prb@
identifier platform.probefn, pdev;
expression e, e1, e2;
@@
probefn(struct platform_device *pdev, ...) {
<+...
- e = kzalloc(e1, e2)
+ e = devm_kzalloc(&pdev->dev, e1, e2)
...
?-kfree(e);
...+>
}
@rem depends on prb@
identifier platform.removefn;
expression e;
@@
removefn(...) {
<...
- kfree(e);
...>
}
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function is small enough, we don't need a extra function for this.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes a unnecessary state read. The status value is never
evaluate after reading the state.
Also rename the status variable to dvdd, because this variable will be
used later.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch resets the irq line before we are requesting the irq. This
avoids pending interrupts before requesting.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is already handled by the of_match_ptr macro.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a at86rf230_device_id table to offers various module
aliases.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Reported-by: Varka Bhadram <varkabhadram@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Reported-by: Varka Bhadram <varkabhadram@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch replace the gpio_request functions with devm_gpio_request_one
functions. Then we don't need to take care about freeing gpios.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch replace request_irq with devm_request_irq. With
devm_request_irq we don't need to care about freeing the irq.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We don't need to set these values at request_irq. The interrupt line is
already configured to same value like irq_get_trigger_type returned.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the platform data for the irq_type. We use instead
the irq_get_trigger_type function to get these flags which should
already configured by the interrupt controller.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Aring