Lock the mutex in the mv88e6xxx_port_vlan_prepare function
called by the DSA stack, instead of doing it in the internal
mv88e6xxx_port_check_hw_vlan helper.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using the define here makes the code more expressive.
Signed-off-by: Hubert Feurstein <h.feurstein@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have an ERPS (Ethernet Ring Protection Switching) setup involving
mv88e6250 switches which we're in the process of switching to a BSP
based on the mainline driver. Breaking any link in the ring works as
expected, with the ring reconfiguring itself quickly and traffic
continuing with almost no noticable drops. However, when plugging back
the cable, we see 5+ second stalls.
This has been tracked down to the userspace application in charge of
the protocol missing a few CCM messages on the good link (the one that
was not unplugged), causing it to broadcast a "signal fail". That
message eventually reaches its link partner, which responds by
blocking the port. Meanwhile, the first node has continued to block
the port with the just plugged-in cable, breaking the network. And the
reason for those missing CCM messages has in turn been tracked down to
the VTU apparently being too busy servicing load/purge operations that
the normal lookups are delayed.
Initial state, the link between C and D is blocked in software.
_____________________
/ \
| |
A ----- B ----- C *---- D
Unplug the cable between C and D.
_____________________
/ \
| |
A ----- B ----- C * * D
Reestablish the link between C and D.
_____________________
/ \
| |
A ----- B ----- C *---- D
Somehow, enough VTU/ATU operations happen inside C that prevents
the application from receving the CCM messages from B in a timely
manner, so a Signal Fail message is sent by C. When B receives
that, it responds by blocking its port.
_____________________
/ \
| |
A ----- B *---* C *---- D
Very shortly after this, the signal fail condition clears on the
BC link (some CCM messages finally make it through), so C
unblocks the port. However, a guard timer inside B prevents it
from removing the blocking before 5 seconds have elapsed.
It is not unlikely that our userspace ERPS implementation could be
smarter and/or is simply buggy. However, this patch fixes the symptoms
we see, and is a small optimization that should not break anything
(knock wood). The idea is simply to avoid doing an VTU load of an
entry identical to the one already present. To do that, we need to
know whether mv88e6xxx_vtu_get() actually found an existing entry, or
has just prepared a struct mv88e6xxx_vtu_entry for us to load. To that
end, let vlan->valid be an output parameter. The other two callers of
mv88e6xxx_vtu_get() are not affected by this patch since they pass
new=false.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each iteration of for_each_available_child_of_node puts the previous
node, but in the case of a return from the middle of the loop, there is
no put, thus causing a memory leak. Hence add an of_node_put before the
return.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a 1ms delay after reset deactivation. Otherwise the chip returns
bogus ID value. This is observed with 88E6390 (Peridot) chip.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a no-op that simply moves all locking and unlocking of
->reg_lock into trivial helpers. I did that to be able to easily add
some ad hoc instrumentation to those helpers to get some information
on contention and hold times of the mutex. Perhaps others want to do
something similar at some point, so this frees them from doing the
'sed -i' yoga, and have a much smaller 'git diff' while fiddling.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DSA ports must flood unknown unicast and multicast, but the switch
must not flood the CPU ports with unknown multicast, as this results
in a lot of undesirable traffic that the network stack needs to filter
in software.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During a port FDB dump operation, the mutex protecting the concurrent
access to the switch registers is currently held by the internal
mv88e6xxx_port_db_dump and mv88e6xxx_port_db_dump_fid helpers.
It must be held at the higher level in mv88e6xxx_port_fdb_dump which
is called directly by DSA through ds->ops->port_fdb_dump. Fix this.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some ISDN files that got removed in net-next had some changes
done in mainline, take the removals.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Free AF_PACKET po->rollover properly, from Willem de Bruijn.
2) Read SFP eeprom in max 16 byte increments to avoid problems with
some SFP modules, from Russell King.
3) Fix UDP socket lookup wrt. VRF, from Tim Beale.
4) Handle route invalidation properly in s390 qeth driver, from Julian
Wiedmann.
5) Memory leak on unload in RDS, from Zhu Yanjun.
6) sctp_process_init leak, from Neil HOrman.
7) Fix fib_rules rule insertion semantic change that broke Android,
from Hangbin Liu.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (33 commits)
pktgen: do not sleep with the thread lock held.
net: mvpp2: Use strscpy to handle stat strings
net: rds: fix memory leak in rds_ib_flush_mr_pool
ipv6: fix EFAULT on sendto with icmpv6 and hdrincl
ipv6: use READ_ONCE() for inet->hdrincl as in ipv4
Revert "fib_rules: return 0 directly if an exactly same rule exists when NLM_F_EXCL not supplied"
net: aquantia: fix wol configuration not applied sometimes
ethtool: fix potential userspace buffer overflow
Fix memory leak in sctp_process_init
net: rds: fix memory leak when unload rds_rdma
ipv6: fix the check before getting the cookie in rt6_get_cookie
ipv4: not do cache for local delivery if bc_forwarding is enabled
s390/qeth: handle error when updating TX queue count
s390/qeth: fix VLAN attribute in bridge_hostnotify udev event
s390/qeth: check dst entry before use
s390/qeth: handle limited IPv4 broadcast in L3 TX path
net: fix indirect calls helpers for ptype list hooks.
net: ipvlan: Fix ipvlan device tso disabled while NETIF_F_IP_CSUM is set
udp: only choose unbound UDP socket for multicast when not in a VRF
net/tls: replace the sleeping lock around RX resync with a bit lock
...
This adds support for the Marvell 88E6250. I've checked that each
member in the ops-structure makes sense, and basic switchdev
functionality works fine.
It uses the new dual_chip option, and since its port registers start
at SMI address 0x08 or 0x18 (i.e., always sw_addr + 0x08), we need to
introduce a new compatible string in order for the auto-identification
in mv88e6xxx_detect() to work.
The chip has four per port 16-bits statistics registers, two of which
correspond to the existing "sw_in_filtered" and "sw_out_filtered" (but
at offsets 0x13 and 0x10 rather than 0x12 and 0x13, because why should
this be easy...). Wiring up those four statistics seems to require
introducing a STATS_TYPE_PORT_6250 bit or similar, which seems a tad
ugly, so for now this just allows access to the STATS_TYPE_BANK0 ones.
The chip does have ptp support, and the existing
mv88e6352_{gpio,avb,ptp}_ops at first glance seem like they would work
out-of-the-box, but for simplicity (and lack of testing) I'm eliding
this.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
When non-bridged, non-vlan'ed mv88e6xxx port is moving down, error
message is logged:
failed to kill vid 0081/0 for device eth_cu_1000_4
This is caused by call from __vlan_vid_del() with vin set to zero, over
call chain this results into _mv88e6xxx_port_vlan_del() called with
vid=0, and mv88e6xxx_vtu_get() called from there returns -EINVAL.
On symmetric path moving port up, call goes through
mv88e6xxx_port_vlan_prepare() that calls mv88e6xxx_port_check_hw_vlan()
that returns -EOPNOTSUPP for zero vid.
This patch changes mv88e6xxx_vtu_get() to also return -EOPNOTSUPP for
zero vid, then this error code is explicitly cleared in
dsa_slave_vlan_rx_kill_vid() and error message is no longer logged.
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here is another set of reviewed patches that adds SPDX tags to different
kernel files, based on a set of rules that are being used to parse the
comments to try to determine that the license of the file is
"GPL-2.0-or-later" or "GPL-2.0-only". Only the "obvious" versions of
these matches are included here, a number of "non-obvious" variants of
text have been found but those have been postponed for later review and
analysis.
There is also a patch in here to add the proper SPDX header to a bunch
of Kbuild files that we have missed in the past due to new files being
added and forgetting that Kbuild uses two different file names for
Makefiles. This issue was reported by the Kbuild maintainer.
These patches have been out for review on the linux-spdx@vger mailing
list, and while they were created by automatic tools, they were
hand-verified by a bunch of different people, all whom names are on the
patches are reviewers.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXPCHLg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykxyACgql6ktH+Tv8Ho1747kKPiFca1Jq0AoK5HORXI
yB0DSTXYNjMtH41ypnsZ
=x2f8
-----END PGP SIGNATURE-----
Merge tag 'spdx-5.2-rc3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull yet more SPDX updates from Greg KH:
"Here is another set of reviewed patches that adds SPDX tags to
different kernel files, based on a set of rules that are being used to
parse the comments to try to determine that the license of the file is
"GPL-2.0-or-later" or "GPL-2.0-only". Only the "obvious" versions of
these matches are included here, a number of "non-obvious" variants of
text have been found but those have been postponed for later review
and analysis.
There is also a patch in here to add the proper SPDX header to a bunch
of Kbuild files that we have missed in the past due to new files being
added and forgetting that Kbuild uses two different file names for
Makefiles. This issue was reported by the Kbuild maintainer.
These patches have been out for review on the linux-spdx@vger mailing
list, and while they were created by automatic tools, they were
hand-verified by a bunch of different people, all whom names are on
the patches are reviewers"
* tag 'spdx-5.2-rc3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (82 commits)
treewide: Add SPDX license identifier - Kbuild
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 225
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 224
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 223
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 222
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 221
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 220
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 218
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 217
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 216
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 215
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 214
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 213
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 211
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 210
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 209
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 207
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 206
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 203
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 201
...
Currently, the upper half of a 4-byte STATS_TYPE_PORT statistic ends
up in bits 47:32 of the return value, instead of bits 31:16 as they
should.
Fixes: 6e46e2d821 ("net: dsa: mv88e6xxx: Fix u64 statistics")
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Marvell SOHO switches have several ways to access the internal
registers. One of them being the System Management Interface (SMI),
using the MDC and MDIO pins, with direct and indirect variants.
In preparation for adding support for other register accesses, move
the SMI code into its own files. At the same time, refine the code
to make it clear that the indirect variant is implemented using the
direct variant accessing only two registers for command and data.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow an interrupt number to be passed in the platform data. The
driver will then use it if not zero, otherwise it will poll for
interrupts.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the NO_CPU strap is set, the switch starts in 'dumb hub' mode, with
all ports enable. Ports which are then actively used are reconfigured
as required when the driver starts. However unused ports are left
alone. Change this to disable them, and turn off any SERDES
interface. This could save some power and so reduce the temperature a
bit.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When requested to disable a port, set the port STP state to disabled.
This fully disables the port and should save some power.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the legacy method of probing the mv88e6xxx driver, now that all
the mainline boards have been converted to use mdio based probing for
a number of cycles.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
phylink will call the mac_config() callback once per second when
polling a PHY or a fixed link. The MAC driver is not supposed to
reconfigure the MAC if nothing has changed.
Make the mv88e6xxx driver look at the current configuration of the
port, and return early if nothing has changed.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This partially reverts ed8fe20205 ("net: dsa: mv88e6xxx: prevent
interrupt storm caused by mv88e6390x_port_set_cmode"). I missed
that chip->ports[].cmode is overwritten anyway by the cmode
caching in mv88e6xxx_setup().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By default, the switch driver is expected to configure CPU and DSA
ports to their maximum speed. For the 6341 and 6390 families, the
ports interface mode has to be configured as well. The 6390X range
support 10G ports using XAUI, while the 6341 and 6390 supports
2500BaseX, as their maximum speed.
Fixes: 787799a9d5 ("net: dsa: mv88e6xxx: Default ports 9/10 6390X CMODE to 1000BaseX")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the original patch I missed to add mv88e6xxx_ports_cmode_init()
to the second probe function, the one for the new DSA framework.
Fixes: ed8fe20205 ("net: dsa: mv88e6xxx: prevent interrupt storm caused by mv88e6390x_port_set_cmode")
Reported-by: Shaokun Zhang <zhangshaokun@hisilicon.com>
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
If an external PHY is connected via SGMII and uses in-band signalling
then the auto-negotiated values aren't propagated to the port,
resulting in a broken link. See discussion in [0]. This patch adds
this propagation. We need to call mv88e6xxx_port_setup_mac(),
therefore export it from chip.c.
Successfully tested on a ZII DTU with 88E6390 switch and an
Aquantia AQCS109 PHY connected via SGMII to port 9.
[0] https://marc.info/?t=155130287200001&r=1&w=2
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ports 9 and 10 don't have internal PHY's but are (dependent on the
version) SERDES/SGMII/XAUI/RXAUI ports.
v2:
- fix it for all 88E6x90 family members
Fixes: bc3931557d ("net: dsa: mv88e6xxx: Add number of internal PHYs")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Despite what the datesheet says, the silicon implements the older way
of snapshoting the statistics. Change the op.
Reported-by: Chris.Healy@zii.aero
Tested-by: Chris.Healy@zii.aero
Fixes: 0ac64c3949 ("net: dsa: mv88e6xxx: mv88e6161 uses mv88e6320 stats snapshot")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
When debugging another issue I faced an interrupt storm in this
driver (88E6390, port 9 in SGMII mode), consisting of alternating
link-up / link-down interrupts. Analysis showed that the driver
wanted to set a cmode that was set already. But so far
mv88e6390x_port_set_cmode() doesn't check this and powers down
SERDES, what causes the link to break, and eventually results in
the described interrupt storm.
Fix this by checking whether the cmode actually changes. We want
that the very first call to mv88e6390x_port_set_cmode() always
configures the registers, therefore initialize port.cmode with
a value that is different from any supported cmode value.
We have to take care that we only init the ports cmode once
chip->info->num_ports is set.
v2:
- add small helper and init the number of actual ports only
Fixes: 364e9d7776 ("net: dsa: mv88e6xxx: Power on/off SERDES on cmode change")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The switch maintains u64 counters for the number of octets sent and
received. These are kept as two u32's which need to be combined. Fix
the combing, which wrongly worked on u16's.
Fixes: 80c4627b27 ("dsa: mv88x6xxx: Refactor getting a single statistic")
Reported-by: Chris Healy <Chris.Healy@zii.aero>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Topaz family should have different phylink_validate method from the
Peridot, since on Topaz the port supporting 2500BaseX mode is port 5,
not 9 and 10.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
No current DSA driver makes use of the phydev parameter passed to the
disable_port call. Remove it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to hold the register lock while requesting the GPIO
interrupt. By not holding it we can also avoid a false positive
lockdep splat.
Reported-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following false positive lockdep splat has been observed.
======================================================
WARNING: possible circular locking dependency detected
4.20.0+ #302 Not tainted
------------------------------------------------------
systemd-udevd/160 is trying to acquire lock:
edea6080 (&chip->reg_lock){+.+.}, at: __setup_irq+0x640/0x704
but task is already holding lock:
edff0340 (&desc->request_mutex){+.+.}, at: __setup_irq+0xa0/0x704
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (&desc->request_mutex){+.+.}:
mutex_lock_nested+0x1c/0x24
__setup_irq+0xa0/0x704
request_threaded_irq+0xd0/0x150
mv88e6xxx_probe+0x41c/0x694 [mv88e6xxx]
mdio_probe+0x2c/0x54
really_probe+0x200/0x2c4
driver_probe_device+0x5c/0x174
__driver_attach+0xd8/0xdc
bus_for_each_dev+0x58/0x7c
bus_add_driver+0xe4/0x1f0
driver_register+0x7c/0x110
mdio_driver_register+0x24/0x58
do_one_initcall+0x74/0x2e8
do_init_module+0x60/0x1d0
load_module+0x1968/0x1ff4
sys_finit_module+0x8c/0x98
ret_fast_syscall+0x0/0x28
0xbedf2ae8
-> #0 (&chip->reg_lock){+.+.}:
__mutex_lock+0x50/0x8b8
mutex_lock_nested+0x1c/0x24
__setup_irq+0x640/0x704
request_threaded_irq+0xd0/0x150
mv88e6xxx_g2_irq_setup+0xcc/0x1b4 [mv88e6xxx]
mv88e6xxx_probe+0x44c/0x694 [mv88e6xxx]
mdio_probe+0x2c/0x54
really_probe+0x200/0x2c4
driver_probe_device+0x5c/0x174
__driver_attach+0xd8/0xdc
bus_for_each_dev+0x58/0x7c
bus_add_driver+0xe4/0x1f0
driver_register+0x7c/0x110
mdio_driver_register+0x24/0x58
do_one_initcall+0x74/0x2e8
do_init_module+0x60/0x1d0
load_module+0x1968/0x1ff4
sys_finit_module+0x8c/0x98
ret_fast_syscall+0x0/0x28
0xbedf2ae8
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&desc->request_mutex);
lock(&chip->reg_lock);
lock(&desc->request_mutex);
lock(&chip->reg_lock);
&desc->request_mutex refer to two different mutex. #1 is the GPIO for
the chip interrupt. #2 is the chained interrupt between global 1 and
global 2.
Add lockdep classes to the GPIO interrupt to avoid this.
Reported-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are not specifying an explicit format argument but instead passing a
string litteral which causes these two warnings to show up:
drivers/net/dsa/mv88e6xxx/chip.c: In function
'mv88e6xxx_irq_poll_setup':
drivers/net/dsa/mv88e6xxx/chip.c:483:2: warning: format not a string
literal and no format arguments [-Wformat-security]
chip->kworker = kthread_create_worker(0, dev_name(chip->dev));
^~~~
drivers/net/dsa/mv88e6xxx/ptp.c: In function 'mv88e6xxx_ptp_setup':
drivers/net/dsa/mv88e6xxx/ptp.c:403:4: warning: format not a string
literal and no format arguments [-Wformat-security]
dev_name(chip->dev));
^~~~~~~~
LD [M] drivers/net/dsa/mv88e6xxx/mv88e6xxx.o
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the bridge flags to Marvell 88e6xxx bridges, allowing
the multicast and unicast flood properties to be controlled. These
can be controlled on a per-port basis via commands such as:
bridge link set dev lan1 flood on|off
bridge link set dev lan1 mcast_flood on|off
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The netfilter conflicts were rather simple overlapping
changes.
However, the cls_tcindex.c stuff was a bit more complex.
On the 'net' side, Cong is fixing several races and memory
leaks. Whilst on the 'net-next' side we have Vlad adding
the rtnl-ness support.
What I've decided to do, in order to resolve this, is revert the
conversion over to using a workqueue that Cong did, bringing us back
to pure RCU. I did it this way because I believe that either Cong's
races don't apply with have Vlad did things, or Cong will have to
implement the race fix slightly differently.
Signed-off-by: David S. Miller <davem@davemloft.net>
The GPIO interrupt controller on the espressobin board only supports edge interrupts.
If one enables the use of hardware interrupts in the device tree for the 88E6341, it is
possible to miss an edge. When this happens, the INTn pin on the Marvell switch is
stuck low and no further interrupts occur.
I found after adding debug statements to mv88e6xxx_g1_irq_thread_work() that there is
a race in handling device interrupts (e.g. PHY link interrupts). Some interrupts are
directly cleared by reading the Global 1 status register. However, the device interrupt
flag, for example, is not cleared until all the unmasked SERDES and PHY ports are serviced.
This is done by reading the relevant SERDES and PHY status register.
The code only services interrupts whose status bit is set at the time of reading its status
register. If an interrupt event occurs after its status is read and before all interrupts
are serviced, then this event will not be serviced and the INTn output pin will remain low.
This is not a problem with polling or level interrupts since the handler will be called
again to process the event. However, it's a big problem when using level interrupts.
The fix presented here is to add a loop around the code servicing switch interrupts. If
any pending interrupts remain after the current set has been handled, we loop and process
the new set. If there are no pending interrupts after servicing, we are sure that INTn has
gone high and we will get an edge when a new event occurs.
Tested on espressobin board.
Fixes: dc30c35be7 ("net: dsa: mv88e6xxx: Implement interrupt support.")
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
By using an external PHY, ports 9 and 10 can support 2500BaseT.
So set this link mode in the mask when validating.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On one hand, the mv88e6xxx driver has a work queue called in loop
which will attempt register accesses after MDIO bus suspension, that
entirely freezes the platform during suspend.
On the other hand, the DSA core is not ready yet to support suspend to
RAM operation because so far there is no way to recover reliably the
switch configuration.
To avoid the kernel to freeze when suspending with a switch driven by
the mv88e6xxx driver, we choose to prevent the driver suspension and
in the same way, the whole platform.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 6390 copper ports have an errata which require poking magic values
into undocumented magic registers and then performing a software
reset.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lots of conflicts, by happily all cases of overlapping
changes, parallel adds, things of that nature.
Thanks to Stephen Rothwell, Saeed Mahameed, and others
for their guidance in these resolutions.
Signed-off-by: David S. Miller <davem@davemloft.net>
The 6320 family of switches uses the same watchdog registers as the
6390.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the ethtool_regs version is set to 0 for all DSA drivers.
Use this field to store the chip ID to simplify the pretty dump of
any interfaces registered by the "dsa" driver.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We already have a workaround for a couple of switches whose internal
PHYs only have the Marvel OUI, but no model number. We detect such
PHYs and give them the 6390 ID as the model number. However the
mv88e6161 has two SERDES interfaces in the same address range as its
internal PHYs. These suffer from the same problem, the Marvell OUI,
but no model number. As a result, these SERDES interfaces were getting
the same PHY ID as the mv88e6390, even though they are not PHYs, and
the Marvell PHY driver was trying to drive them.
Add a special case to stop this from happen.
Reported-by: Chris Healy <Chris.Healy@zii.aero>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 6390X family has 8 SERDES interfaces. When ports 9 and 10 are not
using all their SERDES interfaces, the unused ones can be assigned to
ports 2-8. Add support for interrupts from SERDES interfaces connected
to these lower ports.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The X family variants support additional ports modes, for 10G
operation, which the non-X variants don't have. Add a port_set_cmode()
for non-X variants to enforce this.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a fix for the port_set_speed method for the Topaz family.
Currently the same method is used as for the Peridot family, but
this is wrong for the SERDES port.
On Topaz, the SERDES port is port 5, not 9 and 10 as in Peridot.
Moreover setting alt_bit on Topaz only makes sense for port 0 (for
(differentiating 100mbps vs 200mbps). The SERDES port does not
support more than 2500mbps, so alt_bit does not make any difference.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MV88E6xxx can have external PHYs attached to certain ports and those
PHYs could even be on different MDIO bus than the one within the switch.
This patch makes sure that ports with such PHYs are configured correctly
according to the information provided by the PHY.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 6352 family has one SERDES interface, which can be used by either
port 4 or port 5. Add interrupt support for the SERDES interface, and
report when the link status changes.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some boards the interrupt can be shared between multiple devices.
For example on Turris Mox the interrupt is shared between all switches.
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
We added a new error path, but we need to drop the lock before we return.
Fixes: 2d2e1dd299 ("net: dsa: mv88e6xxx: Cache the port cmode")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
phylink wants to know when the MAC layers notices a change in the
link. For the 6390 family, this is a change in the SERDES state.
Add interrupt support for the SERDES interface used to implement
SGMII/1000Base-X/2500Base-X. This is currently limited to ports 9 and
10. Support for the 10G SERDES and other ports will be added later,
building on this basic framework.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
An up coming change will register interrupts for individual switch
ports, using the mv88e6xxx_port as the interrupt context information.
Add members to the mv88e6xxx_port structure so we can link it back to
the mv88e6xxx_chip member the port belongs to and the port number of
the port.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ports CMODE indicates the type of link between the MAC and the
PHY. It is used often in the SERDES code. Rather than read it each
time, cache its value.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 6390 has two SERDES interfaces, used by ports 9 and 10. The 6390X
has eight SERDES interfaces. These allow ports 9 and 10 to do 10G. Or
if lower speeds are used, some of the SERDES interfaces can be used by
ports 2-8 for 1000Base-X.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add rudimentary phylink support to mv88e6xxx.
TODO:
- needs to call phylink_mac_change() when the port link comes up/goes down.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 6185 can enable/disable 802.3z pause be setting the MyPause bit in
the port status register. Add an op to support this.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The BTF conflicts were simple overlapping changes.
The virtio_net conflict was an overlap of a fix of statistics counter,
happening alongisde a move over to a bonafide statistics structure
rather than counting value on the stack.
Signed-off-by: David S. Miller <davem@davemloft.net>
Version 1 of the patch adding SERDES support to the 88E6141/6341
correctly added the ops to the 88E6141/6341. However, by the time
version 3 was committed, the ops had moved to the 88E6085/6175. Put
them back where they belong.
Fixes: 5bafeb6e7e ("net: dsa: mv88e6xxx: 88E6141/6341 SERDES support")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
free_irq() waits until all handlers for this IRQ have completed. As the
relevant handler (mv88e6xxx_g1_irq_thread_fn()) takes the chip's reg_lock
it might never return if the thread calling free_irq() holds this lock.
For the same reason kthread_cancel_delayed_work_sync() in the polling case
must not hold this lock.
Also first free the irq (or stop the worker respectively) such that
mv88e6xxx_g1_irq_thread_work() isn't called any more before the irq
mappings are dropped in mv88e6xxx_g1_irq_free_common() to prevent the
worker thread to call handle_nested_irq(0) which results in a NULL-pointer
exception.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6165 family has its global clock in the PTP global
registers. It does not support any form of PTP events. Add a function
to read the clock, fill in an ops structure, and register it with the
two members of the family.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MV88E6165 PTP registers are all in AVB bank F, unlike newer
generations which spread them over AVB bank E and F. Implement AVB ops
for the MV88E6165 which hides this difference.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6165 family supports PTP, but its registers use a different
layout to the currently supported devices. Abstract accessing the PTP
registers into a set of ops, so making space for a second
implementation.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make it explicit that either device tree is used or platform data. If
neither is available, abort the probe.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: 877b7cb0b6 ("net: dsa: mv88e6xxx: Add minimal platform_data support")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In mv88e6xxx_probe(), ("np" or "pdata") might be an invariant
but GCC can't see that, therefore:
drivers/net/dsa/mv88e6xxx/chip.c: In function ‘mv88e6xxx_probe’:
drivers/net/dsa/mv88e6xxx/chip.c:4420:13: warning: ‘compat_info’ may be used uninitialized in this function [-Wmaybe-uninitialized]
chip->info = compat_info;
Actually, it should have warned on the "if (!compat_info)" test, but
whatever.
Explicitly initialize to NULL in the variable declaration to
deal with this.
Fixes: 877b7cb0b6 ("net: dsa: mv88e6xxx: Add minimal platform_data support")
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the size of the EEPROM to the platform data, so it can also be
instantiated by a platform device.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not all the world uses device tree. Some parts of the world still use
platform devices and platform data. Add basic support for probing a
Marvell switch via platform data.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A number of drivers have the following pattern:
if (np)
of_mdiobus_register()
else
mdiobus_register()
which the implementation of of_mdiobus_register() now takes care of.
Remove that pattern in drivers that strictly adhere to it.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Fugang Duan <fugang.duan@nxp.com>
Reviewed-by: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the Global 1 specific setup function only setup the statistics
unit, kill it in favor of a mv88e6xxx_stats_setup function.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All Marvell switch families except 88E6390 have direct registers in
Global 1 for IEEE and IP priorities override mapping. The 88E6390 uses
indirect tables instead.
Add .ieee_pri_map and .ip_pri_map ops to distinct that and call them
from a mv88e6xxx_pri_setup helper. Only non-6390 are concerned ATM.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bpf syscall and selftests conflicts were trivial
overlapping changes.
The r8169 change involved moving the added mdelay from 'net' into a
different function.
A TLS close bug fix overlapped with the splitting of the TLS state
into separate TX and RX parts. I just expanded the tests in the bug
fix from "ctx->conf == X" into "ctx->tx_conf == X && ctx->rx_conf
== X".
Signed-off-by: David S. Miller <davem@davemloft.net>
Add rudimentary phylink support to mv88e6xxx. This allows the driver
using user ports with fixed links to keep operating normally. User ports
with normal PHYs are not affected since the switch automatically manages
their link parameters. User facing ports which use a SFP/SFF with a
non-fixed link mode might require a call to phylink_mac_change() to
operate properly.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
[Andrew: fixed link setting after adding link polling]
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
[florian: expand commit message]
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RMU mode bits moved a lot within the Global Control 2 register of
the Marvell switch families. Add an .rmu_disable op to support at least
3 known alternatives.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
All Marvell switches supported by mv88e6xxx have to set their device
number in the Global Control 2 register. Extract this in a read then
write function, called from the device mapping setup code.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only the 88E6185 family has bits 15:12 Cascade Port bits in the Global
Control 2 register. Hence inconsistent values are actually written in
this register for other families.
Add a .set_cascade_port operation to isolate the 88E6185 case, and call
it from the device mapping setup function.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 88E6141/6341 switches (also known as Topaz) have 1 SGMII lane,
which can be configured the same way as the SERDES lane on 88E6390.
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most of the mv88e6xxx switches have the PHYs at address 0, 1, 2, ...
The 6341 however has the PHYs at 0x10, 0x11, 0x12. Add a parameter to
the info structure for this base address.
Testing of 6f88284f3b ("net: dsa: mv88e6xxx: Add MDIO interrupts for
internal PHYs") was performed on the 6341. So it works only on the
6341. Use this base information to correctly set the interrupt.
Fixes: 6f88284f3b ("net: dsa: mv88e6xxx: Add MDIO interrupts for internal PHYs")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The remaining values written to the Switch Management Register in the
mv88e6xxx_g2_setup function are specific to 88E6352 and older, and are
the default values anyway.
Thus remove completely this function. The mv88e6xxx driver no more
contains setup code to access arbitrary Global 2 registers.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the Device Mapping setup out of the specific Global 2 code,
into the top level device setup function.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the trunking setup out of Global 2 specific setup into the top
level mv88e6xxx_setup function.
Note that the 88E6390 family calls this LAG instead of Trunk and
supports 32 possible ID routing vectors, with LAG ID bit 4 being placed
in Global 2 register 0x1D...
We don't need Trunk (or LAG) IDs for the moment, thus keep it simple.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
U64_MAX is well defined now while the UINT64_MAX is not, so we fall
back to drivers' own definition as below:
#ifndef UINT64_MAX
#define UINT64_MAX (u64)(~((u64)0))
#endif
I believe this is in one phy driver then copied and pasted to other phy
drivers.
Replace the UINT64_MAX with U64_MAX to clean up the source code.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Up until now we largely assumed that we were interested in ETH_SS_STATS
type of strings for all ethtool operations, this is about to change with
the introduction of additional string sets, e.g: ETH_SS_PHY_STATS.
Update all functions to take an appropriate stringset argument and act
on it when it is different than ETH_SS_STATS for now.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Count the numbers of various ATU and VTU violation statistics and
return them as part of the ethtool -S statistics.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When free'ing the polled IRQs, call the common irq free code.
Otherwise the interrupts are left registered, and when we come to load
the driver a second time, we get an Opps.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
By calling request_threaded_irq() with the flag IRQF_TRIGGER_FALLING
we override the trigger mode provided in device tree. And the
interrupt is actually active low, which is what all the current device
tree descriptions use.
Suggested-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Tested-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The switch name is emitted in the kernel log, so having the right name
there is nice.
Fixes: 1558727a1c ("net: dsa: mv88e6xxx: Add support for ethernet switch 88E6141")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
When registering an MDIO bus, it is possible to pass an array of
interrupts, one per address on the bus. phylib will then associate the
interrupt to the PHY device, if no other interrupt is provided.
Some of the global2 interrupts are PHY interrupts. Place them into the
MDIO bus structure.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add to the info structure the number of internal PHYs, if they generate
interrupts. Some of the older generations of switches have internal
PHYs, but no interrupt registers. In this case, set the count to zero.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the recent change to polling for interrupts, it is important that
the number of global 1 interrupts is listed. Without it, the driver
requests an interrupt domain for zero interrupts, which returns
EINVAL, and the probe fails.
Add two missing entries.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can hit the register lock not held assertion with the following path:
[ 34.170631] mv88e6085 0.1:00: Switch registers lock not held!
[ 34.176510] CPU: 0 PID: 950 Comm: ethtool Not tainted 4.16.0-rc4 #143
[ 34.182985] Hardware name: Freescale Vybrid VF5xx/VF6xx (Device Tree)
[ 34.189519] Backtrace:
[ 34.192033] [<8010c4b4>] (dump_backtrace) from [<8010c788>] (show_stack+0x20/0x24)
[ 34.199680] r6:9f5dc010 r5:00000011 r4:9f5dc010 r3:00000000
[ 34.205434] [<8010c768>] (show_stack) from [<80679d38>] (dump_stack+0x24/0x28)
[ 34.212719] [<80679d14>] (dump_stack) from [<804844a8>] (mv88e6xxx_read+0x70/0x7c)
[ 34.220376] [<80484438>] (mv88e6xxx_read) from [<804870dc>] (mv88e6xxx_port_get_cmode+0x34/0x4c)
[ 34.229257] r5:a09cd128 r4:9ee31d07
[ 34.232880] [<804870a8>] (mv88e6xxx_port_get_cmode) from [<80487e6c>] (mv88e6352_port_has_serdes+0x24/0x64)
[ 34.242690] r4:9f5dc010
[ 34.245309] [<80487e48>] (mv88e6352_port_has_serdes) from [<804880b8>] (mv88e6352_serdes_get_stats+0x28/0x12c)
[ 34.255389] r4:00000001
[ 34.257973] [<80488090>] (mv88e6352_serdes_get_stats) from [<804811e8>] (mv88e6xxx_get_ethtool_stats+0xb0/0xc0)
[ 34.268156] r10:00000000 r9:00000000 r8:00000000 r7:a09cd020 r6:00000001 r5:9f5dc01c
[ 34.276052] r4:9f5dc010
[ 34.278631] [<80481138>] (mv88e6xxx_get_ethtool_stats) from [<8064f740>] (dsa_slave_get_ethtool_stats+0xbc/0xc4)
mv88e6xxx_get_ethtool_stats() calls mv88e6xxx_get_stats() which calls both
chip->info->ops->stats_get_stats(), which holds the register lock, and
chip->info->ops->serdes_get_stats() which does not. Have
chip->info->ops->serdes_get_stats() be running with the register lock held to
avoid such assertions.
Fixes: 436fe17d27 ("net: dsa: mv88e6xxx: Allow the SERDES interfaces to have statistics")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Handle polled interrupts correctly when loading the module.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Fixes: 294d711ee8 ("net: dsa: mv88e6xxx: Poll when no interrupt defined")
Signed-off-by: David S. Miller <davem@davemloft.net>
Call the common irq free function, rather than going recursive and
blowing away the stack, followed by the machine.
Fixes: 294d711ee8 ("net: dsa: mv88e6xxx: Poll when no interrupt defined")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for reading the SERDES statistics of the mv88e8352, using
the standard ethtool -S option. The SERDES interface can be mapped to
either port 4 or 5, so only return statistics on those ports, if the
SERDES interface is in use.
The counters are reset on read, so need to be accumulated. Add a per
port structure to hold the stats counters. The 6352 only has a single
SERDES interface and so only one port will using the newly added
array. However the 6390 family has as many SERDES interfaces as ports,
each with statistics counters. Also, PTP has a number of counters per
port which will also need accumulating.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot