As discussed in
http://thread.gmane.org/gmane.linux.kernel/1249726/focus=1288990,
the capability introduced in 4d7e30d989
to govern EPOLLWAKEUP seems misnamed: this capability is about governing
the ability to suspend the system, not using a particular API flag
(EPOLLWAKEUP). We should make the name of the capability more general
to encourage reuse in related cases. (Whether or not this capability
should also be used to govern the use of /sys/power/wake_lock is a
question that needs to be separately resolved.)
This patch renames the capability to CAP_BLOCK_SUSPEND. In order to ensure
that the old capability name doesn't make it out into the wild, could you
please apply and push up the tree to ensure that it is incorporated
for the 3.5 release.
Signed-off-by: Michael Kerrisk <mtk.manpages@gmail.com>
Acked-by: Serge Hallyn <serge.hallyn@canonical.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
b43 with open firmware crashes mac80211 because
it changes the number of queues at runtime which,
while it was never really supported, now crashes
mac80211 due to the new hardware queue logic.
Fix this by detecting open vs. proprietary fw
earlier and registering with mac80211 with the
right number of queues.
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Cc: stable@vger.kernel.org (depends on commit a6f38ac3)
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Using work_pending() to defer certain operations when
a HW-reset work has been queued is racy since the check
would return false when the work item is actually in
execution. Use SC_OP_HW_RESET instead to fix this race.
Also, unify the reset debug statistics maintenance.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When an interface in AP or P2P-GO mode is removed,
check whether a station interface is already present and
reconfigure the beacon timers etc. properly if it's
associated.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, there are problems with how ANI is handled in
multi-VIF scenarios. This patch addresses them by unifying
the start/stop logic.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove unused variables, use a helper function to choose
the slot and reset beaconing status at one place.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Setup the beacon queue parameters after disabling
interrupts. Also, remove the redundant call in conf_tx()
for IBSS mode since the queue would be configured
with the appropriate cwmin/cwmax values when beaconing
is enabled.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the tx_last_beacon() callback, mac80211's beaconing
status can be used instead. The beacon tasklet doesn't require
it because it is disabled when removing a slot.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* The beaconing status routine is not required, since in
multi-VIF cases the HW beacon parameters should not be
re-configured.
* Remove SC_OP_TSF_RESET - when a beaconing interface comes
up the first time, the TSF has to be reset.
* Simplify ath9k_allow_beacon_config().
* Handle setting/clearing the SWBA interrupt properly.
* Remove the TSF mangling in IBSS mode, it is not required.
* General code cleanup.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cleanup the messy logic dealing with station association
and disassociation.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Do not set/clear TSF when adding/deleting an interface.
This should be done when the BSS is set up and should also
take into account the existence of other interfaces.
* Set opmode explicitly.
* ANI setup needs to be decided based on multiple interfaces.
This can be done via the bss_info_changed() callback.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch revamps interface addition and deletion and simplifies
slot allocation. There is no need to setup the beacon buffer
in add/remove interface, remove this and use simple APIs for
assigning/deleting slots.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We found a deadlock in the handling of command failures/reset conditions.
For example:
1. Two commands are in the queue.
2. The first command is sent, but causes a timeout, which kicks off an
asynchronous device reset
3. The second command is queued (but not yet sent to the hardware)
4. The device reset kicks in, causing the if_usb disconnect handler to
set the "surprise removed" flag to be set as the device disappears
from the bus. This causes lbs_thread to stop processing things
("adapter removed; waiting to die"), not processing any further
commands, leaving the second queued command "in the air", causing a
deadlock.
Fix this by removing the surpriseremoved flag setting in if_usb. I can't
see any reason why this needs to be done so early. lbs_remove_card will set
this flag at an appropriate time - i.e. after all pending commands have
been completed or cancelled, avoiding this deadlock.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fail commands immediately when the request cannot be sent to the hardware.
This solves the following deadlock:
1. Two commands are in the queue.
2. The first command is sent, but causes a timeout, which kicks off an
asynchronous device reset
3. The second command is submitted to the device, and fails. The failure
is noted but the existing code waits for the timeout handler to take
care of the failure.
4. The device reset kicks in, causing the device "surprise removed" flag
to be set as the device disappears from the bus.
5. lbs_thread notes this and enters "adapter removed; waiting to die"
mode, without processing any further command timeouts.
While adjusting lbs thread logic to handle this situation may be one way
to fix this, it seems more practical to simplify handling of host_to_card
failure so that the commands are failed immediately without waiting for
more compliated timeout logic to kick in.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
reg_notifier can be called before the interface is up.
Handle this correctly by storing the requested country code, then
apply the relevant configuration when the interface is brought up.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR9485, AR9330 and AR9340 are the chips that this is *NOT* supposed to be
applied on.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
- add an inline function for getting the correct modal EEPROM struct
- remove unnecessary indirection through ath9k_hw_ar9300_get_eeprom
access the relevant fields directly
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If the aggregate size exceeds the TXOP limit, it leads to lots of unnecessary
hardware and software retries.
The previous 4ms frame limit table was completely undocumented, the commit
that updated it only vaguely referenced and equation from the standard,
but I've been unable to replicate its results.
Fix this by using a formula based on the code in ath_pkt_duration, which is
more likely to be correct for this case.
Reported-by: Dave Täht <dave.taht@gmail.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Prepare for using different queue size defaults for each AC.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In all those years apparently nobody noticed that the txop limit programmed
into the chip was off by a factor of 32 (!), probably because the VI and VO
queues aren't used that much aside from mgmt frames on VO.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The row/column sizes can be derived from the array argument within the macro
itself, which is less error prone. In a few cases the supplied column size
was actually wrong.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the EEPROM information to choose the right tx gain table
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Many chips are not able to deal with non-consecutive rx antenna selections
and respond with calibration errors, reset errors, etc.
When an antenna is selected as a tx antenna, also flag it for rx to avoid
chip issues.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch configures data rates to firmware using bitrate mask
provided by cfg80211.
Earlier we used to only update band information in this handler
which will be used later for ibss network. Due to recent
modifications in ibss join code we don't need to do that.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In mwifiex_set_rf_channel() ibss specific flags were unnecessarily
getting modified for infra and AP mode. This patch removes
mwifiex_set_rf_channel() function and adds equivalant code in infra,
ibss and AP path.
For ibss, now we are chosing band based on channel type and basic
rates provided in ibss join request. We can start ibss network in
A only, B only, G only, BG, BGN, AN mode.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
1) Remove unnecessary wrapper functions.
2) Currently we don't have command to set Tx data rate, so
mwifiex_rate_ioctl_set_rate_value() function and related code
can be removed.
3) "ds_rate" filled by mwifiex_ret_tx_rate_cfg() is never used.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
1) Recently we removed set_channel cfg80211 handler. Also, cfg80211
blocks ibss connection requests if ibss network is already started
/joined. Hence the code to restart ibss network in new channel
(mwifiex_drv_change_adhoc_chan() function) becomes redundant.
2) mwifiex_bss_set_channel() function is redundant. It does some
error checking and calculate adhoc start band and adhoc channel.
Cfg80211 already takes care of error checking and provides correct
channel information to the driver. Adhoc start band is already
calculated in mwifiex_set_rf_channel() function.
Other associated code is also removed in this patch.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The old code was an accidental copy&paste of the 2.4 GHz version,
which doesn't work.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit d83579e2a5 incorporated some
changes from the vendor driver that made it newly important that the
calculated hardware version correctly include the CHIP_92D bit, as all
of the IS_92D_* macros were changed to depend on it. However, this bit
was being unset for dual-mac, dual-phy devices. The vendor driver
behavior was modified to not do this, but unfortunately this change was
not picked up along with the others. This caused scanning in the 2.4GHz
band to be broken, and possibly other bugs as well.
This patch brings the version calculation logic in parity with the
vendor driver in this regard, and in doing so fixes the regression.
However, the version calculation code in general continues to be largely
incoherent and messy, and needs to be cleaned up.
Signed-off-by: Forest Bond <forest.bond@rapidrollout.com>
Cc: Stable <stable@vger.kernel.org> [v3.2+]
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The mac80211 rate_index changed to be a u8, so
can't hold the negative error value properly.
Use a temporary variable for error checking.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Turns out every most standard Linux distributions enable
CONFIG_EXPERT, so use the shiny new CFG80211_CERTIFICATION_ONUS
which is meant by design to not be enabled by all Linux
distributions.
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch introduces a flags variable to the Three-wire UART state
struct and converts the two existing bools in the struct into flags.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
The configuration request/response messages contain a configuration
field which contains the sliding window size (amount of unacked reliable
packets that can be pending). This patch makes sure that we configure
the correct size (minimum of local and remote values) and use it when
determining whether to send new packets or not.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
The implementation of h5_build_packet can be moved into
h5_prepare_pkt since all h5_prepare_pkt does is determine whether the
packet is reliable and then call h5_build_packet.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This patch adds on-demand wakeup request sending (and re-sendind) when
we are in low-power state. When the controller enters this state it will
send a sleep message after which the host is not allowed to send any
other packets until a wakeup request has been sent and the woken message
received as a response to it. The wakeup requests are re-sent
periodically until a woken message is received.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This patch adds tracking for the uninitialized, initialized and active
states for Three-wire UART. This is needed so we can handle periodic
sending of the Link Establishment messages before reaching active state
and so that we do not try to do any higher level HCI data transmission
before reaching active state.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This patch adds very basic support for the sleep related messages. The
only thing the code does right now is send a wakeup message as soon as
receiving a sleep one, essentially preventing the controller from going
to sleep.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Remove unnecessary debug logs and add some to more centralized places.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This patch takes into use the delayed initialization feature that the
Bluetooth UART framework provides.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Michael Kerrisk