We should provide to inet6_csk_route_socket a struct flowi6 pointer,
so that net6_csk_xmit() works correctly instead of sending garbage.
Also add some consts
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Yuchung Cheng <ycheng@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When AP interface is going down, the stations
are flushed (in ieee80211_do_stop()) only after
the beaconing was stopped.
However, drivers might rely on stations being
removed before the beaconing was stopped, in
order to clean up properly.
Fix it by flushing the stations on ap stop.
(we already do the same for other interface
types, e.g. in ieee80211_set_disassoc())
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
should fix the following issue
[ 3229.815012] [ BUG: lock held when returning to user space! ]
[ 3229.815016] 3.5.0-rc7-wl #28 Tainted: G W O
[ 3229.815017]
------------------------------------------------
[ 3229.815019] wpa_supplicant/5783 is leaving the kernel with locks still held!
[ 3229.815022] 1 lock held by wpa_supplicant/5783:
[ 3229.815023] #0: (reg_mutex){+.+.+.}, at: [<fa65834d>]
reg_last_request_cell_base+0x1d/0x60 [cfg80211]
Cc: Luis Rodriguez <mcgrof@gmail.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Tested-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In some rare cases, the CMD_ROC completion may take over 1 second.
The timeout had earlier been increased to 1000ms (from 750ms), but it
is still not enoug. Increase it to 1500ms.
Signed-off-by: Luciano Coelho <coelho@ti.com>
We need to wait for the command completion event when we send the
CMD_ROLE_STOP event otherwise we may try to send CMD_ROLE_START too
soon and get out-of-sync with the firmware.
In some cases, the firmware may not send the event, so we wait for the
event or for the timeout, whichever comes first.
This patch is based on an earlier version by Eliad.
Cc: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Use this opportunity to consolidate the check for MIMO support into a
separate function.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
handle errors of nla_put() inside the if(nla_put...) {}
This makes the code simpler and clearer because:
we take advantage from the fact that we have only one nla_put
in our routines (so no real need for goto label).
this avoids ugly goto forward followed by goto backward.
Signed-off-by: Yair Shapira <yair.shapira@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
this completes the calibrator based fem detect logic in driver:
driver starts (by calibrator) in plt_mode PLT_FEM_DETECT
wlcore inits and starts plt on wl12xx
wl12xx fetches fem number from firmware and stores it in wl->fem_manuf
wl12xx immediatly returns (doesn't start radio, etc...)
wlcore returns the fem_manuf to calibrator using WL1271_TM_ATTR_DATA
plt_mode is stopped
Signed-off-by: Yair Shapira <yair.shapira@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
bip calibration is not required in wl18xx. Therefore we
disable also auto fem (using calibrator fem detect) mode.
Signed-off-by: Yair Shapira <yair.shapira@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
add wl->plt_mode that is used to indicate different plt
working modes: this will be used to implement calibrator side
auto fem detection where driver asks firmware to detect
the wlan fem radio type and returns it to calibrator.
this is not implemented yet and plt_modes: PLT_ON and
PLT_FEM_DETECT currently behave the same.
Signed-off-by: Yair Shapira <yair.shapira@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
After the latest mac80211 changes, the sta has
the ap's sta pointer even before association.
This cause the auth and assoc frames to be sent
with the standard ap's rates, rather than the
basic rates.
Change the tx rate policy logic to use the regular
ap rates only for data packets (so control and mgmt
packets will be sent with basic rates)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
During interface removal, don't adjust sleep_auth if we are during
recovery. Since the FW is potentially dead we shouldn't talk to it.
Reported-by: Yossi Wortzel <yossiw@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Initialize val to 0, to remove the following warning with
CONFIG_CC_OPTIMIZE_FOR_SIZE. The compiler used was gcc 4.4.1
(Sourcery G++ Lite 2010q1-202).
drivers/net/wireless/ti/wl18xx/io.c: In function 'wl18xx_top_reg_read':
drivers/net/wireless/ti/wl18xx/io.c:57: warning: 'val' may be used uninitialized in this function
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Send EAPOLs using minimum basic rate for AP, STA, p2p GO and Client.
The patch fixes p2p connection issue with Realtek device in p2p
certification test 5.1.13 (DEVUT reinvokes Persistent Group).
Signed-off-by: Igal Chernobelsky <igalc@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
ht_mode added to wl18xx conf struct in order to support different modes
from the configuration file, as well as module params, and by default
(working without a conf file and/or no module params).
the hack regarding conf.phy.low_band_component_type for each board
is now explicitly handled after parsing module params.
missing default values to wl18xx config added.
fix string module params not to have defaults (so if empty, param
can be taken from conf file).
update conf version to 3.
Signed-off-by: Yair Shapira <yair.shapira@ti.com>
Signed-off-by: Ido Reis <idor@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
suspend and resume callbacks configure wakeup conditions to the FW
which may be different between suspend and resume.
This feature is currently not utilized as both in suspend and resume
FW wakeup every 1 DTIM. Avoid waking up the chip and doing the FW command
unless there's an actual difference in the wakeup conditions.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
We get DMA alignment trouble if the beginning of the conf.phy struct is
not aligned to 4 bytes. Use kmemdup to ensure alignment.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
On spear320 device supported mode are:
* AUTO_NET_SMII_MODE
* AUTO_NET_MII_MODE
* AUTO_EXP_MODE
* SMALL_PRINTERS_MODE
* EXTENDED_MODE
spear320-evb board is designed for EXTENDED_MODE only, hence it does not
boot correctly in current form where pinctrl part for some devices fail.
Configure and boot the SPEAr320 evaluation board in EXTENDED_MODE.
Signed-off-by: Vipul Kumar Samar <vipulkumar.samar@st.com>
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
sys_clk has multiple parents and selection of parent depends on sys_clk_ctrl
register bit no. 23:25, with following possibilities
0XX: pll1_clk
10X: sys_synth_clk
110: pll2_clk
111: pll3_clk
Out of several possibilities (h/w wise) to select same clock parent for
sys_clk, current clock implementation was considering just one value.
When bootloader programmed different (valid) value to select a clock
parent then Linux breaks.
Here, we try to include all possibilities which can lead to same
clock selection thus making Linux independent of bootloader selection
values.
Signed-off-by: Vipul Kumar Samar <vipulkumar.samar@st.com>
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
This patch is to fix typing mistake of clk enable register of i2c1 and
uart1.
Signed-off-by: Vipul Kumar Samar <vipulkumar.samar@st.com>
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
The max limit of con_id is 16 and dev_id is 20. As of now for spear6xx, many clk
ids are exceeding this predefined limit.
This patch is intended to rename clk ids like:
mux_clk -> _mclk
gate_clk -> _gclk
synth_clk -> syn_clk
ras_gen1_synth_gate_clk -> ras_syn1_gclk
pll3_48m -> pll3_
Signed-off-by: Vipul Kumar Samar <vipulkumar.samar@st.com>
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
The max limit of con_id is 16 and dev_id is 20. As of now for spear3xx, many clk
ids are exceeding this predefined limit.
This patch is intended to rename clk ids like:
mux_clk -> _mclk
gate_clk -> _gclk
synth_clk -> syn_clk
ras_gen1_synth_gate_clk -> ras_syn1_gclk
ras_pll3_48m -> ras_pll3_
pll3_48m -> pll3_
Signed-off-by: Vipul Kumar Samar <vipulkumar.samar@st.com>
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
The max limit of con_id is 16 and dev_id is 20. As of now for spear1310, many
clk ids are exceeding this predefined limit.
This patch is intended to rename clk ids like:
mux_clk -> _mclk
gate_clk -> _gclk
synth_clk -> syn_clk
gmac_phy -> phy_
gmii_125m_pad -> gmii_pad
Signed-off-by: Vipul Kumar Samar <vipulkumar.samar@st.com>
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
The max limit of con_id is 16 and dev_id is 20. As of now for spear1340, many
clk ids are exceeding this predefined limit.
This patch rename clk ids like:
mux_clk -> _mclk
gate_clk -> _gclk
synth_clk -> syn_clk
gmac_phy -> phy_
gmii_125m_pad_ -> gmii_pad
Signed-off-by: Vipul Kumar Samar <vipulkumar.samar@st.com>
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
This change updates the descriptor macros to accept pointers, updates the
name to drop the _ADV suffix, and include the IXGBEVF name in the macro.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change is meant to make the code much more readable for MTQC and MRQC
configuration.
The big change is that I simplified much of the logic so that we are
essentially handling just 4 cases and their variants. In the cases where
RSS is disabled we are actually just programming the RETA table with all
1s resulting in a single queue RSS. In the case of SR-IOV I am treating
that as a subset of VMDq. This all results int he following configuration
for the hardware:
DCB
En Dis
VMDq En VMDQ/DCB VMDq/RSS
Dis DCB/RSS RSS
Cc: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change cleans up some of the logic in an attempt to try and simplify
things for how we are configuring DCB w/ RSS.
In this patch I basically did 3 things. I updated the logic for getting
the first register index. I applied the fact that all TCs get the same
number of queues to simplify the looping logic in caching the DCB ring
register. Finally I updated how we configure the RQTC register to match
the fact that all TCs are assigned the same number of queues.
Cc: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
It makes much more sense for us to configure the real number of Tx and Rx
queues in the ixgbe_open call than it does in ixgbe_set_num_queues. By
setting the number in ixgbe_open we can avoid a number of unecessary
updates and only have to make the calls once.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Previously we were exiting without cleaning up the memory internally on the
ixgbe_setup_rx_resources and ixgbe_setup_tx_resources calls. Instead of
forcing the caller to clean things up for us we should instead just unwind
the rings and free the memory as we go. This way we can more gracefully
clean up the rings in the event of an allocation failure.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When the link status changes on the PF we need to notify the VFs. In order
to do this we should ping all of the VFs in order to trigger a link status
change on them as well.
This fixes issues in which the PF would reset, but the VF didn't because the
NAK flag was not set in the VF mailbox.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Merge Andrew's remaining patches for 3.5:
"Nine fixes"
* Merge emailed patches from Andrew Morton <akpm@linux-foundation.org>: (9 commits)
mm: fix lost kswapd wakeup in kswapd_stop()
m32r: make memset() global for CONFIG_KERNEL_BZIP2=y
m32r: add memcpy() for CONFIG_KERNEL_GZIP=y
m32r: consistently use "suffix-$(...)"
m32r: fix 'fix breakage from "m32r: use generic ptrace_resume code"' fallout
m32r: fix pull clearing RESTORE_SIGMASK into block_sigmask() fallout
m32r: remove duplicate definition of PTRACE_O_TRACESYSGOOD
mn10300: fix "pull clearing RESTORE_SIGMASK into block_sigmask()" fallout
bootmem: make ___alloc_bootmem_node_nopanic() really nopanic
Offlining memory may block forever, waiting for kswapd() to wake up
because kswapd() does not check the event kthread->should_stop before
sleeping.
The proper pattern, from Documentation/memory-barriers.txt, is:
--- waker ---
event_indicated = 1;
wake_up_process(event_daemon);
--- sleeper ---
for (;;) {
set_current_state(TASK_UNINTERRUPTIBLE);
if (event_indicated)
break;
schedule();
}
set_current_state() may be wrapped by:
prepare_to_wait();
In the kswapd() case, event_indicated is kthread->should_stop.
=== offlining memory (waker) ===
kswapd_stop()
kthread_stop()
kthread->should_stop = 1
wake_up_process()
wait_for_completion()
=== kswapd_try_to_sleep (sleeper) ===
kswapd_try_to_sleep()
prepare_to_wait()
.
.
schedule()
.
.
finish_wait()
The schedule() needs to be protected by a test of kthread->should_stop,
which is wrapped by kthread_should_stop().
Reproducer:
Do heavy file I/O in background.
Do a memory offline/online in a tight loop
Signed-off-by: Aaditya Kumar <aaditya.kumar@ap.sony.com>
Acked-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Reviewed-by: Minchan Kim <minchan@kernel.org>
Acked-by: Mel Gorman <mel@csn.ul.ie>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix the m32r link error:
LD arch/m32r/boot/compressed/vmlinux
arch/m32r/boot/compressed/misc.o: In function `zlib_updatewindow':
misc.c:(.text+0x190): undefined reference to `memcpy'
misc.c:(.text+0x190): relocation truncated to fit: R_M32R_26_PLTREL against undefined symbol `memcpy'
make[5]: *** [arch/m32r/boot/compressed/vmlinux] Error 1
by adding our own implementation of memcpy().
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit a556bec995 ("m32r: fix arch/m32r/boot/compressed/Makefile")
changed "$(suffix_y)" to "$(suffix-y)", but didn't update any location
where "suffix_y" is set, causing:
make[5]: *** No rule to make target `arch/m32r/boot/compressed/vmlinux.bin.', needed by `arch/m32r/boot/compressed/piggy.o'. Stop.
make[4]: *** [arch/m32r/boot/compressed/vmlinux] Error 2
make[3]: *** [zImage] Error 2
Correct the other locations to fix this.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit acdc0d5ef9 ('m32r: fix breakage from "m32r: use generic
ptrace_resume code"') tried to fix a problem in commit e34112e396
("m32r: use generic ptrace_resume code") by returning values in a
function returning void, causing:
arch/m32r/kernel/ptrace.c: In function 'user_enable_single_step':
arch/m32r/kernel/ptrace.c:594:3: warning: 'return' with a value, in function returning void [enabled by default]
arch/m32r/kernel/ptrace.c:598:3: warning: 'return' with a value, in function returning void [enabled by default]
arch/m32r/kernel/ptrace.c:601:3: warning: 'return' with a value, in function returning void [enabled by default]
arch/m32r/kernel/ptrace.c:604:2: warning: 'return' with a value, in function returning void [enabled by default]
Remove the unneeded return values.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit a610d6e672 ("pull clearing RESTORE_SIGMASK into
block_sigmask()") caused:
arch/m32r/kernel/signal.c: In function 'handle_signal':
arch/m32r/kernel/signal.c:289:6: warning: 'return' with a value, in function returning void [enabled by default]
Remove the return value it forgot to remove.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix the m32r build warning:
include/linux/ptrace.h:66:0: warning: "PTRACE_O_TRACESYSGOOD" redefined [enabled by default]
arch/m32r/include/asm/ptrace.h:117:0: note: this is the location of the previous definition
We already have it in <linux/ptrace.h>, so remove it from <asm/ptrace.h>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit a610d6e672 ("pull clearing RESTORE_SIGMASK into
block_sigmask()") caused:
arch/mn10300/kernel/signal.c: In function 'handle_signal':
arch/mn10300/kernel/signal.c:462:3: warning: 'return' with no value, in function returning non-void [-Wreturn-type]
Add the missing return values, and restore the indentation while we're
at it.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: David Howells <dhowells@redhat.com>
Cc: Koichi Yasutake <yasutake.koichi@jp.panasonic.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In reaction to commit 99ab7b1944 ("mm: sparse: fix usemap allocation
above node descriptor section") Johannes said:
| while backporting the below patch, I realised that your fix busted
| f5bf18fa22 again. The problem was not a panicking version on
| allocation failure but when the usemap size was too large such that
| goal + size > limit triggers the BUG_ON in the bootmem allocator. So
| we need a version that passes limit ONLY if the usemap is smaller than
| the section.
after checking the code, the name of ___alloc_bootmem_node_nopanic()
does not reflect the fact.
Make bootmem really not panic.
Hope will kill bootmem sooner.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: <stable@vger.kernel.org> [3.3.x, 3.4.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It is not needed for mac_ocp_{write / read}. Actually bit 31 of OCPDR
does not change and r8168_mac_ocp_read always returns ~0.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Tested-by: Francois Romieu <romieu@fr.zoreil.com>
This renames CAP_EPOLLWAKEUP to CAP_BLOCK_SUSPEND to encourage future
reuse of the capability in question in related cases.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)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=oZrz
-----END PGP SIGNATURE-----
Merge tag 'pm-post-3.5-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull a last-minute PM update from Rafael J. Wysocki:
"This renames CAP_EPOLLWAKEUP to CAP_BLOCK_SUSPEND to encourage future
reuse of the capability in question in related cases."
* tag 'pm-post-3.5-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM: Rename CAP_EPOLLWAKEUP to CAP_BLOCK_SUSPEND
free_nh_exceptions() should use rcu_dereference_protected(..., 1)
since its called after one RCU grace period.
Also add some const-ification in recent code.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet