The malidp_hw_device structure that the driver uses to handle the
differences between versions of the IP contains both non-changeable
data and fields that get updated at probe time. Previously we were
copying the read-only part into allocated memory, but that can be
completely avoided by splitting the structure into a read-only part
and keeping the runtime modifiable fields into the old structure.
Reviewed-by: Brian Starkey <brian.starkey@arm.com>
Reviewed-by: Gustavo Padovan <gustavo.padovan@collabora.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
If an instance of Mali DP hardware shares the interrupt line with
another hardware (usually another instance of the Mali DP) its
interrupt handler can get called when the device is suspended.
Check the PM status before making access to the hardware registers
to avoid deadlocks.
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
When downscaling, mclk needs to be sufficiently higher than pxlclk in
order to be able to fetch the higher-resolution data and produce output
pixels. When not scaling, or when upscaling, mclk can be equal to
pxlclk. Since the driver doesn't control mclk, just ensure that the
requirement is satisfied with the current clock rate.
Signed-off-by: Mihail Atanassov <mihail.atanassov@arm.com>
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Enable the scaling engine for upscaling a single plane using the polyphase
scaler. No image enhancement support or downscaling yet*, and composition
result scaling is not implemented.
* Downscaling a plane requires mclk > pxlclk.
Signed-off-by: Mihail Atanassov <mihail.atanassov@arm.com>
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Add gamma via the DRM GAMMA_LUT/GAMMA_LUT_SIZE CRTC
properties. The expected LUT size is 4096 in order
to produce as accurate a set of segments as possible.
This version uses only the green channel's gamma curve
to set the hardware curve on DP550/650. For the sake of
simplicity, it uses the same table of coefficients for
all 3 curves on DP500.
Signed-off-by: Mihail Atanassov <mihail.atanassov@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Use rectangle 1 as a generic plane. Existing code already sets the smart
layer bounding box size + offset. The rectangles' offsets are relative
to the bounding box, so there is no need to set R1's offset (reset value
is 0), just its size which is the same as the bounding box.
Signed-off-by: Mihail Atanassov <mihail.atanassov@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Hardware has multiple (2 or 3, depending on model) stride
registers per layer; add a function that correctly takes that
into account. On hardware that only has 2 stride registers,
ensure that 3-plane (YUV) content has identical strides
for both chroma planes.
Signed-off-by: Mihail Atanassov <mihail.atanassov@arm.com>
[Removed smart layer stride setup, comment and commit message clarifications]
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
We're going to use the same format list for output formats, so rename
everything related to input formats to avoid confusion.
Signed-off-by: Brian Starkey <brian.starkey@arm.com>
[touched commit title to clarify the final struct name]
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
It's possible for CVAL to get set whilst we are in config mode. If this
happens, afer we leave config mode the HW will latch whatever
configuration is in the registers at the next vsync. Most likely this
will be a partial configuration, as we'll be racing against the ongoing
atomic_commit.
To avoid this, clear CVAL before leaving config mode.
Signed-off-by: Brian Starkey <brian.starkey@arm.com>
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Different hardware versions have different requirements when it comes to
pitch alignment. Add a function which can be used to check pitch
alignment for a device.
Signed-off-by: Brian Starkey <brian.starkey@arm.com>
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Add support for the new family of Display Processors from ARM Ltd.
This commit adds basic support for Mali DP500, DP550 and DP650
parts, with only the display engine being supported at the moment.
Cc: David Brown <David.Brown@arm.com>
Cc: Brian Starkey <Brian.Starkey@arm.com>
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Liviu Dudau