The link between the ethernet MAC and its PHY has become more complex
as the interface evolves. This is especially true with serdes links,
where the part of the PHY is effectively integrated into the MAC.
Serdes links can be connected to a variety of devices, including SFF
modules soldered down onto the board with the MAC, a SFP cage with
a hotpluggable SFP module which may contain a PHY or directly modulate
the serdes signals onto optical media with or without a PHY, or even
a classical PHY connection.
Moreover, the negotiation information on serdes links comes in two
varieties - SGMII mode, where the PHY provides its speed/duplex/flow
control information to the MAC, and 1000base-X mode where both ends
exchange their abilities and each resolve the link capabilities.
This means we need a more flexible means to support these arrangements,
particularly with the hotpluggable nature of SFP, where the PHY can
be attached or detached after the network device has been brought up.
Ethtool information can come from multiple sources:
- we may have a PHY operating in either SGMII or 1000base-X mode, in
which case we take ethtool/mii data directly from the PHY.
- we may have a optical SFP module without a PHY, with the MAC
operating in 1000base-X mode - the ethtool/mii data needs to come
from the MAC.
- we may have a copper SFP module with a PHY whic can't be accessed,
which means we need to take ethtool/mii data from the MAC.
Phylink aims to solve this by providing an intermediary between the
MAC and PHY, providing a safe way for PHYs to be hotplugged, and
allowing a SFP driver to reconfigure the serdes connection.
Phylink also takes over support of fixed link connections, where the
speed/duplex/flow control are fixed, but link status may be controlled
by a GPIO signal. By avoiding the fixed-phy implementation, phylink
can provide a faster response to link events: fixed-phy has to wait for
phylib to operate its state machine, which can take several seconds.
In comparison, phylink takes milliseconds.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
- remove sync status
- rework supported and advertisment handling
- add 1000base-x speed for fixed links
- use functionality exported from phy-core, reworking
__phylink_ethtool_ksettings_set for it
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sometimes, we need to do additional work between the PHY coming up and
marking the carrier present - for example, we may need to wait for the
PHY to MAC link to finish negotiation. This changes phylib to provide
a notification function pointer which avoids the built-in
netif_carrier_on() and netif_carrier_off() functions.
Standard ->adjust_link functionality is provided by hooking a helper
into the new ->phy_link_change method.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
phy_lookup_setting() provides useful functionality in ethtool code
outside phylib. Move it to phy-core and allow it to be re-used (eg,
in phylink) rather than duplicated elsewhere. Note that this supports
the larger linkmode space.
As we move the phy settings table, we also need to move the guts of
phy_supported_speeds() as well.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Other code would like to make use of this, so make the speed and duplex
string generation visible, and place it in a separate file.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit e5a03bfd87 ("phy: Add an mdio_device structure")
introduced a spurious trailing semicolon. Remove it.
Signed-off-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add set_loopback in phy_driver, which is used by MAC
driver to enable or disable phy loopback. it also add a generic
genphy_loopback function, which use BMCR loopback bit to enable
or disable loopback.
Signed-off-by: Lin Yun Sheng <linyunsheng@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the Device Tree binding has been updated, update the PHY
library phy_interface_t and phy_modes to support the "internal" PHY
interface type.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make return value void since function never return meaningfull value
Signed-off-by: Yuval Shaia <yuval.shaia@oracle.com>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 4c5e7a2c05 ("dt-bindings: mdio: Clarify binding document")
declared that a MDIO reset GPIO property should have only a single GPIO
reference/specifier, however the supporting code was left intact, still
burdening the kernel with now apparently useless loops -- get rid of them.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
XAUI allows XGMII to reach an extended distance by using a XGXS layer at
each end of the MAC to PHY link, operating over four Serdes lanes.
10GBASE-KR is a single lane Serdes backplane ethernet connection method
with autonegotiation on the link. Some PHYs use this to connect to the
ethernet interface at 10G speeds, switching to other connection types
when utilising slower speeds.
10GBASE-KR is also used for XFI and SFI to connect to XFP and SFP fiber
modules.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
genphy_restart_aneg() can only restart autonegotiation on clause 22
PHYs. Add a phy_restart_aneg() function which selects between the
clause 22 and clause 45 restart functionality depending on the PHY
type and whether the Clause 45 PHY supports the Clause 22 register set.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add generic helpers for 802.3 clause 45 PHYs for >= 10Gbps support.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's unused, so remove it.
Signed-off-by: Yuval Shaia <yuval.shaia@oracle.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some Ethernet drivers will attach/connect to a PHY device before calling
register_netdevice() which is responsible for calling netdev_register_kobject()
which would do the network device's kobject initialization. In such a case,
sysfs_create_link() would return -ENOENT because the network device's kobject
is not ready yet, and we would fail to connect to the PHY device.
In order to keep things simple and symetrical, we just take the success path as
indicative of the ability to access the network device's kobject, and create
the second link if that's the case.
Fixes: 5568363f0c ("net: phy: Create sysfs reciprocal links for attached_dev/phydev")
Reported-by: Woojung Hung <Woojung.Huh@microchip.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added helper function that checks phy_mode is RGMII (all variants)
'bool phy_interface_mode_is_rgmii(phy_interface_t mode)'
Changed the following function, to use the above.
'bool phy_interface_is_rgmii(struct phy_device *phydev)'
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Suggested-by: Florian Fainelli <f.fainelli@gmail.com>
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit fa8cddaf90 ("net phylib: Remove unnecessary condition check in phy")
removed the only place where the PHY flag PHY_HAS_MAGICANEG was
checked. But it left the flag being set in the drivers. Remove the flag.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Ethernet link on an interrupt driven PHY was not coming up if the Ethernet
cable was plugged before the Ethernet interface was brought up.
The patch trigger PHY state machine to update link state if PHY was requested to
do auto-negotiation and auto-negotiation complete flag already set.
During power-up cycle the PHY do auto-negotiation, generate interrupt and set
auto-negotiation complete flag. Interrupt is handled by PHY state machine but
doesn't update link state because PHY is in PHY_READY state. After some time
MAC bring up, start and request PHY to do auto-negotiation. If there are no new
settings to advertise genphy_config_aneg() doesn't start PHY auto-negotiation.
PHY continue to stay in auto-negotiation complete state and doesn't fire
interrupt. At the same time PHY state machine expect that PHY started
auto-negotiation and is waiting for interrupt from PHY and it won't get it.
Fixes: 321beec504 ("net: phy: Use interrupts when available in NOLINK state")
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Cc: stable <stable@vger.kernel.org> # v4.9+
Tested-by: Roger Quadros <rogerq@ti.com>
Tested-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some boards [1] leave the PHYs at an invalid state
during system power-up or reset thus causing unreliability
issues with the PHY which manifests as PHY not being detected
or link not functional. To fix this, these PHYs need to be RESET
via a GPIO connected to the PHY's RESET pin.
Some boards have a single GPIO controlling the PHY RESET pin of all
PHYs on the bus whereas some others have separate GPIOs controlling
individual PHY RESETs.
In both cases, the RESET de-assertion cannot be done in the PHY driver
as the PHY will not probe till its reset is de-asserted.
So do the RESET de-assertion in the MDIO bus driver.
[1] - am572x-idk, am571x-idk, a437x-idk
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a new configuration symbol: MDIO_DEVICE which allows building
the MDIO devices and bus code, without pulling in the entire Ethernet
PHY library and devices code.
PHYLIB nows select MDIO_DEVICE and the relevant Makefile files are
updated to reflect that.
When MDIO_DEVICE (MDIO bus/device only) is selected, but not PHYLIB, we
have mdio-bus.ko as a loadable module, and it does not have a
module_exit() function because the safety of removing a bus class is
unclear.
When both MDIO_DEVICE and PHYLIB are enabled, we need to assemble
everything into a common loadable module: libphy.ko because of nasty
circular dependencies between phy.c, phy_device.c and mdio_bus.c which
are really tough to untangle.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the indirect MMD read/write methods which are now no longer
necessary.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make phy_(read|write)_mmd() generic 802.3 clause 45 register accessors
for both Clause 22 and Clause 45 PHYs, using either the direct register
reading for Clause 45, or the indirect method for Clause 22 PHYs.
Allow this behaviour to be overriden by PHY drivers where necessary.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the phy_(read|write)__mmd() helpers out of line, they will become
our main MMD accessor functions, and so will be a little more complex.
This complexity doesn't belong in an inline function. Also move the
_indirect variants as well to keep like functionality together.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Generic PHY driver is a catch-all PHY driver and it should preserve
whatever prior initialization has been done by boot loader or firmware
agents. For specific PHY device configuration it is expected that a
specialized PHY driver would take over that role.
Resetting the generic PHY was a bad idea that has lead to several
complaints and downstream workarounds e.g: in OpenWrt/LEDE so restore
the behavior prior to 87aa9f9c61 ("net: phy: consolidate PHY
reset in phy_init_hw()").
Reported-by: Felix Fietkau <nbd@nbd.name>
Fixes: 87aa9f9c61 ("net: phy: consolidate PHY reset in phy_init_hw()")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are number of function calls, originating from user-space,
typically through the Ethernet driver that can make us crash by
dereferencing phydev->drv which will be NULL once we unbind the driver
from the PHY.
There are still functional issues that prevent an unbind then rebind to
work, but these will be addressed separately.
Suggested-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow board support code to collect pre-declarations for MDIO devices by
registering them with mdiobus_register_board_info(). SPI and I2C buses
have a similar feature, we were missing this for MDIO devices, but this
is particularly useful for e.g: MDIO-connected switches which need to
provide their port layout (often board-specific) to a MDIO Ethernet
switch driver.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6390 ports 9 and 10 supports some additional PHY modes. Add
these modes to the PHY core so they can be used in the binding.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
<linux/phy.h> includes <linux/phy_led_triggers.h>, which is not really
needed. Drop the include from <linux/phy.h>, and add it to all users
that didn't include it explicitly.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some bus names are pretty long and do not fit into
17 chars. Increase therefore MII_BUS_ID_SIZE and
phy_fixup.bus_id to larger number. Now mii_bus.id
can host larger name.
Signed-off-by: Volodymyr Bendiuga <volodymyr.bendiuga@gmail.com>
Signed-off-by: Magnus Öberg <magnus.oberg@westermo.se>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
>From : Woojung Huh <woojung.huh@microchip.com>
Add functions to unregister phy fixup for modules.
int phy_unregister_fixup(const char *bus_id, u32 phy_uid, u32 phy_uid_mask)
Unregister phy fixup from phy_fixup_list per bus_id, phy_uid &
phy_uid_mask
int phy_unregister_fixup_for_uid(u32 phy_uid, u32 phy_uid_mask)
Unregister phy fixup from phy_fixup_list.
Use it for fixup registered by phy_register_fixup_for_uid()
int phy_unregister_fixup_for_id(const char *bus_id)
Unregister phy fixup from phy_fixup_list.
Use it for fixup registered by phy_register_fixup_for_id()
Signed-off-by: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new parameter mdix_ctrl to hold the user configuration.
Existing mdix maintain the current status of MDI(X) crossover performed or
not.
mdix_ctrl can configure either ETH_TP_MDI or ETH_TP_MDI_X orETH_TP_MDI_AUTO.
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microsemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds an option to disable EEE advertisement in the generic PHY
by providing a mask of prohibited modes corresponding to the value found in
the MDIO_AN_EEE_ADV register.
On some platforms, PHY Low power idle seems to be causing issues, even
breaking the link some cases. The patch provides a convenient way for these
platforms to disable EEE advertisement and work around the issue.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Tested-by: Yegor Yefremov <yegorslists@googlemail.com>
Tested-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding get_tunable/set_tunable function pointer to the phy_driver
structure, and uses these function pointers to implement the
ETHTOOL_PHY_GTUNABLE/ETHTOOL_PHY_STUNABLE ioctls.
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microsemi.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Allan W. Nielsen <allan.nielsen@microsemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function just calls into genphy_restart_aneg() to perform an
autonegotation restart.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make phy_aneg_done() available to drivers so that the result of the
auto-negotiation initiated by phy_start_aneg() can be determined.
Remove the local implementation of phy_aneg_done() from the Aeroflex
driver and use the phy library version.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create an option CONFIG_LED_TRIGGER_PHY (default n), which will create a
set of led triggers for each instantiated PHY device. There is one LED
trigger per link-speed, per-phy.
The triggers are registered during phy_attach and unregistered during
phy_detach.
This allows for a user to configure their system to allow a set of LEDs
not controlled by the phy to represent link state changes on the phy.
LEDS controlled by the phy are unaffected.
For example, we have a board where some of the leds in the
RJ45 socket are controlled by the phy, but others are not. Using the
triggers provided by this patch the leds not controlled by the phy can
be configured to show the current speed of the ethernet connection. The
leds controlled by the phy are unaffected.
Signed-off-by: Josh Cartwright <josh.cartwright@ni.com>
Signed-off-by: Nathan Sullivan <nathan.sullivan@ni.com>
Signed-off-by: Zach Brown <zach.brown@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
phy_supported_speeds provides a means to get a list of all the speeds a
phy device currently supports.
Signed-off-by: Zach Brown <zach.brown@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PHY interrupts are now handled in a threaded interrupt handler,
which can sleep. The work queue is no longer needed, phy_change() can
be called directly. phy_mac_interrupt() still needs to be safe to call
in interrupt context, so keep the work queue, and use a helper to call
phy_change().
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
adds PHY-mode "trgmii" as an extension for the operation
mode of the PHY interface for PHY_INTERFACE_MODE_TRGMII.
and adds a variable trgmii inside mtk_mac as the indication
to make the difference between the MAC connected to internal
switch or connected to external PHY by the given configuration
on the board and then to perform the corresponding setup on
TRGMII hardware module.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ethtool callbacks {get|set}_link_ksettings are often the same, so
we add two generics functions phy_ethtool_{get|set}_link_ksettings
to avoid writing severals times the same function.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Acked-By: David Decotigny <decot@googlers.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The old ethtool api (get_setting and set_setting) has
generic phy functions phy_ethtool_sset and phy_ethtool_gset.
To supprt the new ethtool api (get_link_ksettings and
set_link_ksettings), we add generic phy function
phy_ethtool_ksettings_get and phy_ethtool_ksettings_set.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit e5a03bfd87 ("phy: Add an mdio_device structure") removed addr,
bus and dev member of the phy_device structure.
This patch remove the documentation about those members.
Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not all devices on an MDIO bus are PHYs. Meaning not all MDIO drivers
are PHY drivers. Add support for generic MDIO drivers.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than have each driver set the driver owner field, do it once in
the core code. This will also help with later changes, when the device
structure will move.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than have drivers directly manipulate the mii_bus structure,
provide and API for registering and unregistering devices on an MDIO
bus, and performing lookups.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not all devices attached to an MDIO bus are phys. So add an
mdio_device structure to represent the generic parts of an mdio
device, and place this structure into the phy_device.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Have mdio_alloc() create the array of interrupt numbers, and
initialize it to POLLING. This is what most MDIO drivers want, so
allowing code to be removed from the drivers.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many Ethernet drivers contain the same netdev_info() print statement
about the attached phy. Move it into the phy device code. Additionally
add a varargs function which can be used to append additional
information.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The address of the device can be determined from the phydev structure,
rather than passing it as a parameter.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King