* git://git.infradead.org/battery-2.6:
da9030_battery: Fix race between event handler and monitor
Add MAX17040 Fuel Gauge driver
w1: ds2760_battery: add support for sleep mode feature
w1: ds2760: add support for EEPROM read and write
ds2760_battery: cleanups in ds2760_battery_probe()
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
Staging: octeon-ethernet: Fix race freeing transmit buffers.
Staging: octeon-ethernet: Convert to use net_device_ops.
MIPS: Cavium: Add CPU hotplugging code.
MIPS: SMP: Allow suspend and hibernation if CPU hotplug is available
MIPS: Add arch generic CPU hotplug
DMA: txx9dmac: use dma_unmap_single if DMA_COMPL_{SRC,DEST}_UNMAP_SINGLE set
MIPS: Sibyte: Fix build error if CONFIG_SERIAL_SB1250_DUART is undefined.
MIPS: MIPSsim: Fix build error if MSC01E_INT_BASE is undefined.
MIPS: Hibernation: Remove SMP TLB and cacheflushing code.
MIPS: Build fix - include <linux/smp.h> into all smp_processor_id() users.
MIPS: bug.h Build fix - include <linux/compiler.h>.
The existing code had the following race:
Thread-1 Thread-2
inc/read in_use
inc/read in_use
inc tx_free_list[qos].len
inc tx_free_list[qos].len
The actual in_use value was incremented twice, but thread-1 is going
to free memory based on its stale value, and will free one too many
times. The result is that memory is freed back to the kernel while
its packet is still in the transmit buffer. If the memory is
overwritten before it is transmitted, the hardware will put a valid
checksum on it and send it out (just like it does with good packets).
If by chance the TCP flags are clobbered but not the addresses or
ports, the result can be a broken TCP stream.
The fix is to track the number of freed packets in a single location
(a Fetch-and-Add Unit register). That way it can never get out of sync
with itself.
We try to free up to MAX_SKB_TO_FREE (currently 10) buffers at a time.
If fewer are available we adjust the free count with the difference.
The action of claiming buffers to free is atomic so two threads cannot
claim the same buffers.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Convert the driver to use net_device_ops as it is now mandatory.
Also compensate for the removal of struct sk_buff's dst field.
The changes are mostly mechanical, the content of ethernet-common.c
was moved to ethernet.c and ethernet-common.{c,h} are removed.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch does not change actual behaviour since dma_unmap_page is just
an alias of dma_unmap_single on MIPS.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-2.6-dm: (48 commits)
dm mpath: change to be request based
dm: disable interrupt when taking map_lock
dm: do not set QUEUE_ORDERED_DRAIN if request based
dm: enable request based option
dm: prepare for request based option
dm raid1: add userspace log
dm: calculate queue limits during resume not load
dm log: fix create_log_context to use logical_block_size of log device
dm target:s introduce iterate devices fn
dm table: establish queue limits by copying table limits
dm table: replace struct io_restrictions with struct queue_limits
dm table: validate device logical_block_size
dm table: ensure targets are aligned to logical_block_size
dm ioctl: support cookies for udev
dm: sysfs add suspended attribute
dm table: improve warning message when devices not freed before destruction
dm mpath: add service time load balancer
dm mpath: add queue length load balancer
dm mpath: add start_io and nr_bytes to path selectors
dm snapshot: use barrier when writing exception store
...
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (72 commits)
asus-laptop: remove EXPERIMENTAL dependency
asus-laptop: use pr_fmt and pr_<level>
eeepc-laptop: cpufv updates
eeepc-laptop: sync eeepc-laptop with asus_acpi
asus_acpi: Deprecate in favor of asus-laptop
acpi4asus: update MAINTAINER and KConfig links
asus-laptop: platform dev as parent for led and backlight
eeepc-laptop: enable camera by default
ACPI: Rename ACPI processor device bus ID
acerhdf: Acer Aspire One fan control
ACPI: video: DMI workaround broken Acer 7720 BIOS enabling display brightness
ACPI: run ACPI device hot removal in kacpi_hotplug_wq
ACPI: Add the reference count to avoid unloading ACPI video bus twice
ACPI: DMI to disable Vista compatibility on some Sony laptops
ACPI: fix a deadlock in hotplug case
Show the physical device node of backlight class device.
ACPI: pdc init related memory leak with physical CPU hotplug
ACPI: pci_root: remove unused dev/fn information
ACPI: pci_root: simplify list traversals
ACPI: pci_root: use driver data rather than list lookup
...
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6:
bnx2: Fix the behavior of ethtool when ONBOOT=no
qla3xxx: Don't sleep while holding lock.
qla3xxx: Give the PHY time to come out of reset.
ipv4 routing: Ensure that route cache entries are usable and reclaimable with caching is off
net: Move rx skb_orphan call to where needed
ipv6: Use correct data types for ICMPv6 type and code
net: let KS8842 driver depend on HAS_IOMEM
can: let SJA1000 driver depend on HAS_IOMEM
netxen: fix firmware init handshake
netxen: fix build with without CONFIG_PM
netfilter: xt_rateest: fix comparison with self
netfilter: xt_quota: fix incomplete initialization
netfilter: nf_log: fix direct userspace memory access in proc handler
netfilter: fix some sparse endianess warnings
netfilter: nf_conntrack: fix conntrack lookup race
netfilter: nf_conntrack: fix confirmation race condition
netfilter: nf_conntrack: death_by_timeout() fix
The kernel oopses if this flag is set.
[and neither driver should set it as they call tty_flip_buffer_push from IRQ
paths so have always been buggy]
Signed-off-by: Chuck Ebbert <cebbert@redhat.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since commit 3e3b5c0877 ("tty: use
prepare/finish_wait"), tty_port_block_til_ready() is using
prepare_to_wait()/finish_wait(). Those functions require that the
wait_queue_t be initialised with .func=autoremove_wake_function, via
DEFINE_WAIT().
But the conversion from DECLARE_WAITQUEUE() to DEFINE_WAIT() was not made,
so this code will oops in finish_wait().
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use the newly introduced pci_ioremap_bar() function in drivers/serial.
pci_ioremap_bar() just takes a pci device and a bar number, with the goal
of making it really hard to get wrong, while also having a central place
to stick sanity checks.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix race condition when adding transmit data to active DMA buffer ring
that can cause transmit stall.
Update transmit timeout when adding data to active DMA buffer ring.
Base transmit timeout on amount of buffered data instead of using fixed
value.
Signed-off-by: Paul Fulghum <paulkf@microgate.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Implement the serial polling hooks for the serial_txx9 uart for use with
kgdboc.
This patch once got SOB from Jason on Jul 2008 and (perhaps) merged into
kgdb-next branch, but lost somewhere then. I resend it now with Jason's
Acked-by.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Acked-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I found a little bug.
When configure in ifcfg-eth* is ONBOOT=no,
the behavior of ethtool command is wrong.
# grep ONBOOT /etc/sysconfig/network-scripts/ifcfg-eth2
ONBOOT=no
# ethtool eth2 | tail -n1
Link detected: yes
I think "Link detected" should be "no".
Signed-off-by: Ooiwa Naohiro <nooiwa@miraclelinux.com>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the unusual printk(ASUS_<level> uses to
the more standard pr_fmt and pr_<level>(.
Signed-off-by: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Len Brown <len.brown@intel.com>
Limit cpufv input to acceptables values.
Add an available_cpufv file to show available
presets.
Change cpufv ouput format from %d to %#x, it won't
break compatibility with existing userspace tools, but
it provide a more human readable output.
Signed-off-by: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Len Brown <len.brown@intel.com>
In the default Eee PC distribution, there is a modified
asus_acpi driver. eeepc-laptop is a cleaned version of this
driver. Sync ASL enum and getter/setters with asus_acpi.
Signed-off-by: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Len Brown <len.brown@intel.com>
asus-laptop have been merged in the kernel two years ago,
it is now stable and used by most distribution instead of
the old asus_acpi driver.
Signed-off-by: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Len Brown <len.brown@intel.com>
The bug tracker have moved from sourceforge to
http://dev.iksaif.net . The homepage of the project
is now http://acpi4asus.sf.net with links to the new
bug tracker. No change for the mailing list.
Signed-off-by: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Len Brown <len.brown@intel.com>
Makes asus-laptop platform device the parent device of
backlight and led classes.
With this patch, leds and backlight are also available in
/sys/devices/platform/asus-laptop/ like thinkpad_acpi.
Signed-off-by: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Len Brown <len.brown@intel.com>
If we leave the camera disabled by default, userspace programs (e.g.
Skype, Cheese) leave the user out in the cold saying that the machine
"has no camera." Therefore, it's better to enable camera by default and
let people who really don't want it just disable the thing.
To reduce power usage you should enable USB autosuspend:
echo -n auto > /sys/bus/usb/drivers/uvcvideo/*:*/../power/level
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Len Brown <len.brown@intel.com>
Some BIOS re-use the same processor bus id
in different scope:
\_SB.SCK0.CPU0
\_SB.SCK1.CPU0
But the (deprecated) /proc/acpi/ interface
assumes the bus-id's are unique, resulting in an OOPS
when the processor driver is loaded:
WARNING: at fs/proc/generic.c:590 proc_register+0x148/0x180()
Hardware name: Sunrise Ridge
proc_dir_entry 'processor/CPU0' already registered
Call Trace:
[<ffffffff8023f7ef>] warn_slowpath+0xb1/0xe5
[<ffffffff8036243b>] ? ida_get_new_above+0x190/0x1b1
[<ffffffff803625a8>] ? idr_pre_get+0x5f/0x75
[<ffffffff8030b2f6>] proc_register+0x148/0x180
[<ffffffff8030b4ff>] proc_mkdir_mode+0x3d/0x52
[<ffffffff8030b525>] proc_mkdir+0x11/0x13
[<ffffffffa0014b89>] acpi_processor_start+0x755/0x9bc [processor]
Rename the processor device bus id. And the new bus id will be
generated as the following format:
CPU+ CPU ID
For example: If the cpu ID is 5, then the bus ID will be "CPU5".
If the CPU ID is 10, then the bus ID will be "CPUA".
Yes, this will change the directory names seen
in /proc/acpi/processor/* on some systems.
Before this patch, those directory names where
totally arbitrary strings based on the interal AML device strings.
http://bugzilla.kernel.org/show_bug.cgi?id=13612
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Acerhdf is a driver for Acer Aspire One netbooks. It allows
to access the temperature sensor and to control the fan.
Signed-off-by: Peter Feuerer <peter@piie.net>
Signed-off-by: Andreas Mohr <andi@lisas.de>
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Now that new interface is available,
convert to using it rather than creating a new kernel thread.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Sometimes both acpi video and i915 driver are compiled as modules.
And there exists the strict dependency between the two drivers.
The acpi video bus will be unloaded in course of unloading the i915 driver.
If we unload the acpi video driver, then the kernel oops will be triggered.
Add the reference count to avoid unloading the ACPI video bus twice.
The reference count should be checked before unregistering the acpi video bus.
If the reference count is already zero, it won't unregister it again.
And after the acpi video bus is already unregistered, the reference count
will be set to zero.
http://bugzilla.kernel.org/show_bug.cgi?id=13396
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Linux claims Vista compatibility to the BIOS for a number of
reasons, but this brings hard lockup on some Sony laptops.
Disable Vista compatibility via DMI for these laptops unless
we can figure out what Vista is doing for this platform.
http://bugzilla.kernel.org/show_bug.cgi?id=12904
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
we used to run the hotplug code in keventd_wq.
But when hot removing the ACPI battery device,
power_supply_unregister invokes flush_scheduled_work.
This causes a deadlock. i.e
1. When dock is unplugged, all the hotplug code is run on kevent_wq.
2. the hotplug code removes all the child devices of dock device.
3. removing the child device may invoke flush_scheduled_work
4. flush_scheduled_work waits until all the work on kevent_wq to be
finished, while this will never be true because the hotplug code
is running on keventd_wq...
Introduce a new workqueue for hotplug in this patch.
http://bugzilla.kernel.org/show_bug.cgi?id=13533
Tested-by: Paul Martin <pm@debian.org>
Tested-by: Vojtech Gondzala <vojtech.gondzala@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Reviewed-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Create symbol link from backlight class device to ACPI video device.
More and more laptops are shipped with multiple ACPI
video devices, while we export only one of them to userspace.
With this patch applied, we can know which ACPI video device
is used by "cat /sys/class/backlight/acpi_video0/device/path".
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
* git://git.infradead.org/iommu-2.6:
Intel-IOMMU, intr-remap: source-id checking
Intel-IOMMU, intr-remap: set the whole 128bits of irte when modify/free it
IOMMU Identity Mapping Support (drivers/pci/intel_iommu.c)
The i2c Linux driver for the DesignWare i2c block of Synopsys, which is meant
for AMBA Peripheral Bus. This i2c block is used on SoC chips like the ARM9
based PVG610.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
To support domain-isolation usages, the platform hardware must be
capable of uniquely identifying the requestor (source-id) for each
interrupt message. Without source-id checking for interrupt remapping
, a rouge guest/VM with assigned devices can launch interrupt attacks
to bring down anothe guest/VM or the VMM itself.
This patch adds source-id checking for interrupt remapping, and then
really isolates interrupts for guests/VMs with assigned devices.
Because PCI subsystem is not initialized yet when set up IOAPIC
entries, use read_pci_config_byte to access PCI config space directly.
Signed-off-by: Weidong Han <weidong.han@intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Interrupt remapping table entry is 128bits. Currently, it only sets low
64bits of irte in modify_irte and free_irte. This ignores high 64bits
setting of irte, that means source-id setting will be ignored. This patch
sets the whole 128bits of irte when modify/free it. Following source-id
checking patch depends on this.
Signed-off-by: Weidong Han <weidong.han@intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Identity mapping for IOMMU defines a single domain to 1:1 map all PCI
devices to all usable memory.
This reduces map/unmap overhead in DMA API's and improve IOMMU
performance. On 10Gb network cards, Netperf shows no performance
degradation compared to non-IOMMU performance.
This method may lose some of DMA remapping benefits like isolation.
The patch sets up identity mapping for all PCI devices to all usable
memory. In the DMA API, there is no overhead to maintain page tables,
invalidate iotlb, flush cache etc.
32 bit DMA devices don't use identity mapping domain, in order to access
memory beyond 4GiB.
When kernel option iommu=pt, pass through is first tried. If pass
through succeeds, IOMMU goes to pass through. If pass through is not
supported in hw or fail for whatever reason, IOMMU goes to identity
mapping.
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
On bootup nvidiafb prints the following on my Apple G5:
nvidiafb: CRTC 1appears to have a CRT attached
There should be a space between the '1' and the 'appears'. Add it.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
RDMA: Add __init/__exit macros to addr.c and cma.c
IB/ehca: Bump version number
mlx4_core: Fix dma_sync_single_for_cpu() with matching for_device() calls
IB/mthca: Replace dma_sync_single() use with proper functions
RDMA/nes: Fix FIN state handling under error conditions
RDMA/nes: Fix max_qp_init_rd_atom returned from query device
IB/ehca: Ensure that guid_entry index is not negative
IB/ehca: Tolerate dynamic memory operations before driver load
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (38 commits)
fusion: mptsas, fix lock imbalance
[SCSI] scsi_transport_fc: replace BUS_ID_SIZE by fixed count
sd, sr: fix Driver 'sd' needs updating message
scsi_transport_iscsi: return -EOVERFLOW for Too many iscsi targets
fc_transport: Selective return value from BSG timeout function
fc_transport: The softirq_done function registration for BSG request
sym53c8xx: ratelimit parity errors
explain the hidden scsi_wait_scan Kconfig variable
ibmvfc: Fix endless PRLI loop in discovery
ibmvfc: Process async events before command responses
libfc: Add runtime debugging with debug_logging module parameter
libfcoe: Add runtime debugging with module param debug_logging
fcoe: Add runtime debug logging with module parameter debug_logging
scsi_debug: Add support for physical block exponent and alignment
cnic: add NETDEV_1000 and NETDEVICES to Kconfig select
cnic: Fix __symbol_get() build error.
Revert "[SCSI] cnic: fix error: implicit declaration of function ‘__symbol_get’"
ipr: differentiate pci-x and pci-e based adapters
ipr: add test for MSI interrupt support
scsi_transport_spi: Blacklist Ultrium-3 tape for IU transfers
...
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (62 commits)
V4L/DVB (12131): BUGFIX: An incorrect Carrier Recovery Loop optimization table was being
V4L/DVB (12130): Fix a redundant compiler warning
V4L/DVB (12003): v4l2: Move bounding code outside I2C ifdef block
V4L/DVB (11913): cx231xx: TRY_FMT should not actually set anything
V4L/DVB (11912): em28xx: Use v4l bounding/alignment function
V4L/DVB (11911): cx231xx: Use v4l bounding/alignment function
V4L/DVB (11910): mt9: Use v4l bounding/alignment function
V4L/DVB (11909): cx23885: Use v4l bounding/alignment function
V4L/DVB (11908): w8968cf: Use v4l bounding/alignment function
V4L/DVB (11907): cx88: Use v4l bounding/alignment function
V4L/DVB (11906): saa7134: Use v4l bounding/alignment function
V4L/DVB (11905): vivi: Use v4l bounding/alignment function
V4L/DVB (11904): zoran: Use v4l bounding/alignment functiob
V4L/DVB (11903): sh_mobile_ceu_camera: Use v4l bounding/alignment function
V4L/DVB (11902): pxa-camera: Use v4l bounding/alignment function
V4L/DVB (11901): v4l2: Create helper function for bounding and aligning images
V4L/DVB (12128): v4l2: update framework documentation.
V4L/DVB (12125): v4l2: add new s_config subdev ops and v4l2_i2c_new_subdev_cfg/board calls
V4L/DVB (12122): pvrusb2: De-obfuscate code which handles routing schemes
V4L/DVB (12121): pvrusb2: Improve handling of routing schemes
...
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
libata: don't set IORDY for reset
sata_fsl: Add power mgmt support
[libata] PATA driver for CF interface on AT91SAM9260 SoC
[libata] beautify module parameters
Linus Torvalds