There is helper function used to send EFS Configuration Response.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Assignment is not needed here since err is always gets value.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Channel moves are triggered by changes to the BT_CHANNEL_POLICY
sockopt when an ERTM or streaming-mode channel is connected.
Moves are only started if enable_hs is true.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Do not retransmit previously-sent data when a "receiver ready" s-frame
with the "final" flag is received during a move.
The ERTM state machines will resynchronize at the end of a channel
move, and the state machine needs to avoid state changes during a
move.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Acked-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
When operating over BR/EDR, ERTM accounts for the maximum over-the-air
packet size when setting the PDU size. AMP controllers do not use the
same over-the-air packets, so the PDU size should only be based on the
HCI MTU of the AMP controller.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
The L2CAP spec recommends specific retransmit and monitor timeouts for
ERTM channels that are on AMP controllers. These timeouts are
calculated from the AMP controller's best effort flush timeout.
BR/EDR controllers use the default retransmit and monitor timeouts.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Outgoing ERTM data is queued during a channel move. The ERTM state
machine is partially reset at the start of a move, and must be
resynchronized with the remote state machine at the end of the move.
Data is not sent so that there are no state transitions between the
partial reset and the resync.
Streaming mode frames are dropped during a move.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Acked-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
AMP controllers expect to transmit only "complete" ACL frames. These
frames have both the "start" and "cont" bits set. AMP does not allow
fragmented ACLs.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Acked-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Several different actions may be taken when an AMP physical link
becomes available. A channel being created on an AMP controller must
continue the connection process. A channel being moved needs to
either send a move request or a move response. A failed physical link
will revert to using a BR/EDR controller if possible.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Acked-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
The move confirm response concludes the channel move command sequence.
Receipt of this command indicates that data may begin to flow again.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Acked-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
The logical link confirm callback is executed when the AMP controller
completes its logical link setup. During a channel move, a newly
formed logical link allows a move responder to send a move channel
response. A move initiator will send a move channel confirm. A
failed logical link will end the channel move and send an appropriate
response or confirm command indicating a failure.
If the channel is being created on an AMP controller, L2CAP
configuration is completed after the logical link is set up.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
The move response command includes a result code indicating
"pending", "success", or "failure" status. A pending result is
received when the remote address is still setting up a physical link,
and will be followed by success or failure. On success, logical link
setup will proceed. On failure, the move is stopped. The receiver of
a move channel response must always follow up by sending a move
channel confirm command.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
After sending a move channel response, a move responder waits for a
move channel confirm command. If the received command has a
"confirmed" result the move is proceeding, and "unconfirmed" means the
move has failed and the channel will not change controllers.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Acked-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Two new states are required to implement channel moves with the ERTM
receive state machine.
The "WAIT_P" state is used by a move responder to wait for a "poll"
flag after a move is completed (success or failure). "WAIT_F" is
similarly used by a move initiator to wait for a "final" flag when the
move is completing. In either state, the reqseq value in the
poll/final frame tells the state machine exactly which frame should be
expected next.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Acked-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
On receipt of a channel move request, the request must be validated
based on the L2CAP mode, connection state, and controller
capabilities. ERTM channels must have their state machines cleared
and transmission paused while the channel move takes place.
If the channel is being moved to an AMP controller then
an AMP physical link must be prepared. Moving the channel back to
BR/EDR proceeds immediately.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Acked-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Processing a move channel request involves getting the channel
structure using the destination channel ID. Previous code could only
look up using the source channel ID.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Acked-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Resolves a conflict resolution issue in "Bluetooth: Fix L2CAP coding
style". The remaining connect and create channel response handler is
renamed to better reflect its use for both response types.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Acked-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
The L2CAP create channel request is very similar to an L2CAP connect
request, but it has an additional parameter for the controller ID. If
the controller id is 0, the channel is set up on the BR/EDR controller
(just like a connect request). Using a valid high speed controller ID
will cause the channel to be initially created on that high speed
controller. While the L2CAP data will be initially routed over the
AMP controller, the L2CAP fixed signaling channel only uses BR/EDR.
When a create channel request is received for a high speed controller,
a pending response is always sent first. After the high speed
physical and logical links are complete a success response will be
sent.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
An L2CAP channel using high speed continues to be associated with a
BR/EDR l2cap_conn, while also tracking an additional hci_conn
(representing a physical link on a high speed controller) and hci_chan
(representing a logical link). There may only be one physical link
between two high speed controllers. Each physical link may contain
several logical links, with each logical link representing a channel
with specific quality of service.
During a channel move, the destination channel id, current move state,
and role (initiator vs. responder) are tracked and used by the channel
move state machine. The ident value associated with a move request
must also be stored in order to use it in later move responses.
The active channel is stored in local_amp_id.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
If BREDR L2CAP chan is deleted and this chan is the channel through
which High Speed traffic is routed to AMP then zero pointer to
the chan in amp_mgr to prevent accessing it.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Do not send EFS Configuration Response for High Speed channel yet.
It will be sent after receiving Logical Link Complete event.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
High Speed hci_conn should always have l2cap_conn associated with it.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Check flags type in switch statement and handle new frame
type ACL_COMPLETE used for High Speed data over AMP.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Use of "__" usually means we need to call the function with a lock held,
which is not the case here.
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
When DEFER_SETUP is set defer() will trigger an authorization
request to the userspace.
l2cap_chan_no_defer() is meant to be used when one does not want to
support DEFER_SETUP (A2MP for example).
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This is part of the move the parent socket usage to l2cap_sock.c
The change is safe when it comes to locking, bt_accept_enqueue() is still
protected by the parent socket lock inside the
l2cap_sock_new_connection_cb() code.
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
No one was protecting the state set in l2cap_send_disconn_req()
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
l2cap_conn_unreliable() doesn't take the sk lock, so we need to take it
using l2cap_chan_set_err().
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Since we change the Bluetooth core to run in process context we don't need
to use GFP_ATOMIC in many of places we were using it. The we just replace
by GFP_KERNEL.
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
L2CAP connect requests and create channel requests share a significant
amount of code. This change moves common code to a new function.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
There are two Flush Timeouts: one is old Flush Timeot Option
which is 2 octets and the second is Flush Timeout inside EFS
which is 4 octets long.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
John W. Linville says:
====================
Here is another batch of updates intended for 3.7...
Highlights include an hci_connect re-write in Bluetooth, HCI/LLC
layer separation in NFC, removal of the raw pn544 NFC driver, NFC LLCP
raw sockets support, improved IBSS auth frame handling in mac80211,
full-MAC AP mode notification support in mac80211, a lot of attention
paid to brcmfmac, and the usual level of updates to iwlwifi, ath9k,
mwifiex, and rt2x00, and various other updates.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/team/team.c
drivers/net/usb/qmi_wwan.c
net/batman-adv/bat_iv_ogm.c
net/ipv4/fib_frontend.c
net/ipv4/route.c
net/l2tp/l2tp_netlink.c
The team, fib_frontend, route, and l2tp_netlink conflicts were simply
overlapping changes.
qmi_wwan and bat_iv_ogm were of the "use HEAD" variety.
With help from Antonio Quartulli.
Signed-off-by: David S. Miller <davem@davemloft.net>
Use function to factor out similar code. For BR/EDR send EFS
Configuration Response immediately, for HS response will be sent
after receiving HCI Logical Link Complete event in the following
patches.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Instead of old unsafe batostr function use %pMR print specifier
for printing Bluetooth addresses in sprintf and seq_printf
statements.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Instead of old unsafe batostr function use %pMR print specifier
for printing Bluetooth addresses in debug and error statements.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
When there is no remote AMP controller found fallback to normal
L2CAP sequence.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Choose which L2CAP connection to establish by checking support
for HS and remote side supported features.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
When releasing L2CAP socket which is in BT_CONFIG state l2cap_chan_close
invokes l2cap_send_disconn_req which cancel delayed works which are only
set in BT_CONNECTED state with l2cap_ertm_init. Add state check before
cancelling those works.
...
[ 9668.574372] [21085] l2cap_sock_release: sock cd065200, sk f073e800
[ 9668.574399] [21085] l2cap_sock_shutdown: sock cd065200, sk f073e800
[ 9668.574411] [21085] l2cap_chan_close: chan f073ec00 state BT_CONFIG sk f073e800
[ 9668.574421] [21085] l2cap_send_disconn_req: chan f073ec00 conn ecc16600
[ 9668.574441] INFO: trying to register non-static key.
[ 9668.574443] the code is fine but needs lockdep annotation.
[ 9668.574446] turning off the locking correctness validator.
[ 9668.574450] Pid: 21085, comm: obex-client Tainted: G O 3.5.0+ #57
[ 9668.574452] Call Trace:
[ 9668.574463] [<c10a64b3>] __lock_acquire+0x12e3/0x1700
[ 9668.574468] [<c10a44fb>] ? trace_hardirqs_on+0xb/0x10
[ 9668.574476] [<c15e4f60>] ? printk+0x4d/0x4f
[ 9668.574479] [<c10a6e38>] lock_acquire+0x88/0x130
[ 9668.574487] [<c1059740>] ? try_to_del_timer_sync+0x60/0x60
[ 9668.574491] [<c1059790>] del_timer_sync+0x50/0xc0
[ 9668.574495] [<c1059740>] ? try_to_del_timer_sync+0x60/0x60
[ 9668.574515] [<f8aa1c23>] l2cap_send_disconn_req+0xe3/0x160 [bluetooth]
...
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Conflicts:
net/netfilter/nfnetlink_log.c
net/netfilter/xt_LOG.c
Rather easy conflict resolution, the 'net' tree had bug fixes to make
sure we checked if a socket is a time-wait one or not and elide the
logging code if so.
Whereas on the 'net-next' side we are calculating the UID and GID from
the creds using different interfaces due to the user namespace changes
from Eric Biederman.
Signed-off-by: David S. Miller <davem@davemloft.net>
To make it clear that it may be called from contexts that may not have
any knowledge of L2CAP, we change the connection parameter, to receive
a hci_conn.
This also makes it clear that it is checking the security of the link.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This patch changes the struct l2cap_chan and associated code to use
kref api for object refcounting and freeing.
Suggested-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Jaganath Kanakkassery <jaganath.k@samsung.com>
Signed-off-by: Syam Sidhardhan <s.syam@samsung.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Earlier we were printing chan->psm before assigning any value.
Signed-off-by: Syam Sidhardhan <s.syam@samsung.com>
Acked-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Move the l2cap channel list chan->global_l under the refcnt
protection and free it based on the refcnt.
Signed-off-by: Jaganath Kanakkassery <jaganath.k@samsung.com>
Signed-off-by: Syam Sidhardhan <s.syam@samsung.com>
Reviewed-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Refactor the code in order to use the l2cap_chan_destroy()
from l2cap_chan_put() under the refcnt protection.
Signed-off-by: Jaganath Kanakkassery <jaganath.k@samsung.com>
Signed-off-by: Syam Sidhardhan <s.syam@samsung.com>
Reviewed-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Return values are never used because callers hci_proto_connect_cfm
and hci_proto_disconn_cfm return void.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Do not process A2MP channel in l2cap_security_cfm
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This change addresses an L2CAP ERTM throughput problem when a remote
device does not fully utilize the available transmit window.
The L2CAP ERTM transmit window size determines the maximum number of
unacked frames that may be outstanding at any time. It is configured
separately for each direction of an ERTM connection. Each side sends a
configuration request with a tx_win field indicating how many unacked
frames it is capable of receiving before sending an ack. The
configuration response's tx_win field shows how many frames the
transmitter will actually send before waiting for an ack.
It's important to trace both the actual transmit window (to check for
validity of incoming frames) and the number of frames that the
transmitter will send before waiting (to send acks at the appropriate
time). Now there are separate tx_win and ack_win values. ack_win is
updated based on configuration responses, and is used to determine
when acks are sent.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Correct places where CID and PSM were printed as int. For CID: 0x%4.4x
is used and for PSM: 0x%2.2x.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Avoid unneeded type conversion by correcting type specifiers in debug
statements for L2CAP.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
If remote device sends bogus RFC option with invalid length,
undefined options values are used. Fix this by using defaults when
remote misbehaves.
This also fixes the following warning reported by gcc 4.7.0:
net/bluetooth/l2cap_core.c: In function 'l2cap_config_rsp':
net/bluetooth/l2cap_core.c:3302:13: warning: 'rfc.max_pdu_size' may be used uninitialized in this function [-Wmaybe-uninitialized]
net/bluetooth/l2cap_core.c:3266:24: note: 'rfc.max_pdu_size' was declared here
net/bluetooth/l2cap_core.c:3298:25: warning: 'rfc.monitor_timeout' may be used uninitialized in this function [-Wmaybe-uninitialized]
net/bluetooth/l2cap_core.c:3266:24: note: 'rfc.monitor_timeout' was declared here
net/bluetooth/l2cap_core.c:3297:25: warning: 'rfc.retrans_timeout' may be used uninitialized in this function [-Wmaybe-uninitialized]
net/bluetooth/l2cap_core.c:3266:24: note: 'rfc.retrans_timeout' was declared here
net/bluetooth/l2cap_core.c:3295:2: warning: 'rfc.mode' may be used uninitialized in this function [-Wmaybe-uninitialized]
net/bluetooth/l2cap_core.c:3266:24: note: 'rfc.mode' was declared here
Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
The l2cap_conn_del function tries to cancel_sync the security timer, but
when it's called from the timeout function itself a deadlock occurs.
Subsequently the "hcon->l2cap_data = NULL" that's supposed to protect
multiple calls to l2cap_conn_del never gets cleared and when the
connection finally drops we double free's etc which will crash the
kernel.
This patch fixes the issue by using the HCI_CONN_LE_SMP_PEND for
protecting against this. The same flag is also used for the same purpose
in other places in the SMP code.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This patch changes the default MTU value for L2CAP ATT fixed channel
to L2CAP_DEFAULT_MTU (672 octets).
Differently from others L2CAP channels, in L2CAP ATT fixed channel
there is no MTU negotiation. The MTU value for that channel is up to
the L2CAP implementation. The only restriction in L2CAP spec is the
MTU value must not be less than 23 octets.
At ATT protocol level (on top of L2CAP), we have the ATT_MTU which
defines the maximum size of any ATT message sent between client and
server. GATT profile defines ATT_MTU default value to 23 octets. If
a GATT based profile wants to use ATT_MTU greater than 23 octets
(e.g. HID over GATT profile), it should negotiate a new value by
executing the GATT Exchange MTU sub-procedure.
Thus, in order to support any value of ATT_MTU negotiated at ATT
protocol level, our L2CAP implementation should have L2CAP ATT
fixed channel MTU equal or greater than ATT_MAX_MTU (512 octets).
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Trivial fix, let the code cleaner.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Reviewed-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Simplify the handling of different ERTM header size. We were the same
check in some places of the code, and more is expected to come, so just
replace them with a function.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Acked-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
l2cap_att_channel always returns 0 which is not used.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
l2cap_conless_channel always return 0 which is not used.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
l2cap_data_channel always return 0 which is not used anywhere,
make it void function.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Make A2MP channel special channel which do not reference hci_conn.
This prevents from keeping ACL connection open when all L2CAP
channels got closed.
hci_conn_hold and hci_conn_put are not reference counts on the
hci_conn structure in the typical way. They are reference counts for
the ACL. When you do the last hci_conn_put, the ACL is disconnected
after a timeout.
Reported-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Functions will be always defined and in case not implemented as
dummy __no_func.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
A2MP fixed channel do not have sk
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Move this check to before the channel time creation simplifies the code
and avoid memory allocation if the channel already exist.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Acked-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
These vars are kept in sync so we can use chan->state here.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This move socket specific code to l2cap_sock.c.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This remove a bit more of socket code from l2cap core, this calls set the
SOCK_ZAPPED and do some clean up depending on the socket state.
Reported-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Use chan instead of void * makes more sense here.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This replace code in l2cap_le_conn_ready() by a similar code in
l2cap_chan_ready().
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This is already performed inside l2cap_chan_ready(), so we don't need it
here again.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Acked-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Both FCS and Extended header might be or might not be present in a ERTM
channel.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Reviewed-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
__constant_cpu_to_le16() is the right go here.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Define assigned Protocol and Service Multiplexor (PSM) identifiers
and use them instead of magic numbers.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Define Continuation flag which the only flag used from Flags field
in L2CAP Configuration Request and Response.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Most of the include were unnecessary or already included by some other
header.
Replace module.h by export.h where possible.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Previous callers of l2cap_build_conf_rsp in l2cap_config_req use
flags instead of continuation flag hardcoded value. It does not change
logic and preserve future possible flags.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
These functions were returning always 0, we just make then void.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Reviewed-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The same check is done just before call l2cap_streaming_send()
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Reviewed-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Silence warnings below:
net/bluetooth/l2cap_core.c:1662:24: warning: Using plain integer
as NULL pointer
net/bluetooth/l2cap_core.c:1662:27: warning: Using plain integer
as NULL pointer
net/bluetooth/l2cap_core.c:1683:24: warning: Using plain integer
as NULL pointer
net/bluetooth/l2cap_core.c:1683:27: warning: Using plain integer
as NULL pointer
net/bluetooth/l2cap_core.c:2260:46: warning: Using plain integer
as NULL pointer
net/bluetooth/l2cap_core.c:2574:33: warning: Using plain integer
as NULL pointer
net/bluetooth/l2cap_core.c:2581:33: warning: Using plain integer
as NULL pointer
net/bluetooth/l2cap_core.c:4556:24: warning: Using plain integer
as NULL pointer
net/bluetooth/l2cap_core.c:4556:27: warning: Using plain integer
as NULL pointer
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
chan->tx_q is only initialized if we use ERTM or Streaming mode.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This enables the new receive and transmit state machines.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
The transmit window values must be configured for streaming mode, even
though streaming mode does not have a window. This enables use of
extended headers when the transmit window socket option is set to 64
or larger.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Let the compiler decide if inlining is appropriate.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Since l2cap_send_ack can trigger extra actions like sending iframes,
don't call it. Just send an RR or RNR frame if an ack needs sending.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Different states have different actions for retransmit and monitor
timeouts, so remove the logic for those actions from the timer handlers.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
The ERTM specification requires the retransmit timer to be cancelled
when the monitor timer is set. The retransmit timer cannot be set
again while the monitor timer is pending.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
struct l2cap_ctrl is now used, and the sframe is now sent directly
rather than depending on a separate call.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
REJ frames are sent by the remote device to request that all frames
after a given sequence number be retransmitted. These are also an
implicit indication that the remote device is not in a busy state and
can receive new iframes.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
When a remote device sends an SREJ, retransmit the frame with the
corresponding sequence number (subject to special cases with poll and
final flags). An SREJ is also an implicit indication the the remote
device is not in a busy state.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
As retransmitted packets arrive, attempt to reassemble SDUs. If all
requested retransmissions have been received, acknowledge them and
transition back to the RECV state.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
The ERTM specification lays out three scenarios for sending SREJ
frames to request retransmission of specific frames. l2cap_send_srej
requests all frames up to a given txseq that are not already queued
for reassembly. l2cap_send_srej_tail only requests the most recent
missing frame. l2cap_send_srej_list resends SREJ frames for data that
was requested for resend but never received.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This adds l2cap_ertm_resend to retransmit frames based on the sequence
numbers in chan->retrans_list. If the retransmit limit is reached for
any individual frame is reached, the connection is dropped. skbs that
are cloned already are copied to avoid modifying shared data (this is
uncommon). To retransmit all frames, l2cap_retransmit_all now builds
a list of all unacked sequence numbers and then calls
l2cap_ertm_resend.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This adds a top-level state machine with handlers for two receive
states defined in the ERTM spec, RECV and SREJ_SENT. The reqseq value
of the incoming frame is also validated at the top level and a
disconnection is forced if it is invalid. The actions for the RECV
and SREJ_SENT states are implemented according to the state tables in
the ERTM specification.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This action now exactly matches what is defined in the ERTM
specification, including clearing the remote busy flag and setting the
retransmit timer rather than retransmitting frames directly. The spec
does not retransmit frames as part of this action, since
retransmission is only triggered by REJ, SREJ, or an RR with the final
bit set. struct l2cap_ctrl is also used to set up header values.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This lets the transmit state machine handle local busy state changes,
since different actions are taken in the different transmit states.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
The function now encapsulates more of the logic to either immediately
send an ack if the transmit window is over 75% full, or wait for the
ack timer to expire if the transmit window is not full enough. It is
also able to push out waiting iframes that can carry an
acknowledgement.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This deletes the receive code that had handlers for each frame type at
the top level, and then had logic to determine the receive state
within each handler.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Streaming mode reception is fairly simple, with in-sequence frames
being reassembled as they arrive. Out-of-sequence frames are dropped,
and also clear any partially-assembled SDUs that may exist.
The packet classifier determines if the txseq value of the incoming
packet is expected, invalid (resulting in a disconnection), invalid
(ignorable), duplicate, or having to do with an SREJ request that was
previously sent. The rules for each classification are defined in the
ERTM specification, and consolidating these rules in one place helps
clarify the receive state machine.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Creates a new l2cap_data_rcv function that combines previous code from
l2cap_ertm_data_rcv and l2cap_data_channel. This reduces duplicate
code for streaming mode, and sets up a framework for the ERTM receive
state machine.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
The new implementation uses struct l2cap_ctrl to set up the sframe
fields, and also reduces duplicate acks by canceling the ack timer
whenever an RR or RNR frame is sent. sframe PDU generation is also
split in to a separate function to separate it from the logic related
to the connection state and sframe type.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
The new implementation is aware of the new transmit state machine, and
uses struct l2cap_ctrl to compose ERTM headers. It also has improved
error handling for allocation failures, and does not send the packet
until after all skb and channel data structures are updated.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This new implementation uses struct l2cap_ctrl to compose the
streaming mode headers.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This implements a top-level transmit state machine with handlers for
the two ERTM states defined in the specification: XMIT and WAIT_F.
The state machine accepts an event and, optionally, a list of skbs to
transmit. In addition to data transmission, the local busy state can
be modified, acks are processed, and monitor and retransmit timeouts
are handled. This mirrors the structure of the state tables in the
spec.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This is to allow for ERTM state machine replacement in the patches
that follow.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This fixes a regression from commit
2ead70b839 that is present in all
kernels starting at v3.0.
When L2CAP information was moved to struct l2cap_chan, a check was
added to l2cap_chan_del to avoid certain cleanup operations when ERTM
or streaming mode had not yet been initialized. The logic in the
check did not take in to account that chan->conf_state is set to 0 in
l2cap_chan_ready, so l2cap_chan_del failed to cancel timers and leaked
memory any time the ERTM queues or lists were not empty.
This change makes sure that l2cap_chan_del only returns early if
ERTM initialization was not performed.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If the ERTM SREJ list is properly allocated but the retransmit list
allocation fails, the SREJ list must be freed before returning from
l2cap_ertm_init. l2cap_chan_del will not clean up the SREJ list
if l2cap_ertm_init returns a failure code.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
defer_setup and suspended are now flags into bt_sk().
Signed-off-by: Gustavo Padovan <gustavo@padovan.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
As the comment for l2cap_get_chan_by_scid indicated, the function used
to return a locked socket. The lock for the socket was acquired while
the channel list was also locked.
When locking was moved over to the l2cap_chan structure, the channel
lock was no longer acquired with the channel list still locked. This
made it possible for the l2cap_chan to be deleted after
conn->chan_lock was released but before l2cap_chan_lock was called.
Making the call to l2cap_chan_lock before releasing conn->chan_lock
makes it impossible for the l2cap_chan to be deleted at the wrong
time.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Reviewed-by: Ulisses Furquim <ulisses@profusion.mobi>
Signed-off-by: Gustavo Padovan <gustavo@padovan.org>
The L2CAP MTU for incoming data is verified differently depending on
the L2CAP mode, so the check is best performed in a mode-specific
context. Checking the incoming MTU before HCI fragment reassembly is
a layer violation and assumes all bytes after the standard L2CAP
header are L2CAP data.
This approach causes issues with unsegmented ERTM or streaming mode
frames, where there are additional enhanced or extended headers before
the data payload and possible FCS bytes after the data payload. A
valid frame could be as many as 10 bytes larger than the MTU.
Removing this code is the best fix, because the MTU is checked later
on for all L2CAP data frames (connectionless, basic, ERTM, and
streaming). This also gets rid of outdated locking (socket instead of
l2cap_chan) and an extra lookup of the channel ID.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Reviewed-by: Ulisses Furquim <ulisses@profusion.mobi>
Signed-off-by: Gustavo Padovan <gustavo@padovan.org>
When we add a fragment to a skb, len and data_len fields need to be
updated.
Signed-off-by: Gustavo Padovan <gustavo@padovan.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
If alloc() fails we let the frags linked list with garbage value (the
err ptr value) in its last element.
Reported-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Gustavo Padovan <gustavo@padovan.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Commit 105bdf9ec1 introduced a
regression in L2CAP streaming mode due to rearranged initialization
code that is shared between ERTM and streaming mode. This change
makes sure the transmit queue is initialized in both modes.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Acked-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo@padovan.org>
Commit 94122bbe9c introduced a problem
where tx_send_head was not set to point to the first skb in the ERTM
transmit queue, which stalled data transmission. This change sets
that pointer when transmission is not already in progress.
Reported-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Gustavo Padovan <gustavo@padovan.org>
It fixes L2CAP socket based security level elevation during a
connection. The HID profile needs this (for keyboards) and it is the only
way to achieve the security level elevation when using the management
interface to talk to the kernel (hence the management enabling patch
being the one that exposes this issue).
It enables the userspace a security level change when the socket is
already connected and create a way to notify the socket the result of the
request. At the moment of the request the socket is made non writable, if
the request fails the connections closes, otherwise the socket is made
writable again, POLL_OUT is emmited.
Signed-off-by: Gustavo Padovan <gustavo@padovan.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use more common code for ERTM and streaming mode segmentation and
transmission, and begin using skb control block data for delaying
extended or enhanced header generation until just before the packet is
transmitted. This code is also better suited for resegmentation,
which is needed when L2CAP links are reconfigured after an AMP channel
move.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Reviewed-by: Ulisses Furquim <ulisses@profusion.mobi>
Signed-off-by: Gustavo Padovan <gustavo@padovan.org>
hlen has a fixed size of L2CAP_HDR_SIZE, use this instead.
Signed-off-by: Gustavo Padovan <gustavo@padovan.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
hlen - L2CAP_HDR_SIZE = 0, so we don't need to add them in the
calculation.
Signed-off-by: Gustavo Padovan <gustavo@padovan.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Adding Code Aurora Forum copyright information due to significant
additions of code.
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Gustavo Padovan <gustavo@padovan.org>
L2CAP sockets contain a pointer to l2cap_chan that needs to be
reference counted in order to prevent a possible dangling pointer when
the channel is freed.
There were a few other cases where an l2cap_chan pointer on the stack
was dereferenced after a call to l2cap_chan_del. Those pointers are
also now reference counted.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Gustavo Padovan <gustavo@padovan.org>
l2cap_get_chan_by_ident was not used, but didn't generate a compiler
warning because it was an inline function.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Gustavo Padovan <gustavo@padovan.org>
Structure members used by ERTM or streaming mode need to be
initialized when an ERTM or streaming mode link is configured. Some
duplicate code is also eliminated by moving in to the ERTM init
function.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Gustavo Padovan <gustavo@padovan.org>
These values are now in the nested l2cap_ctrl struct.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo@padovan.org>
In order to establish a LE connection we need the address type
information. User-space already pass this information to kernel
through struct sockaddr_l2.
This patch adds the dst_type parameter to l2cap_chan_connect so we
are able to pass the address type info from user-space down to
hci_conn layer.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Acked-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds the dst_type parameter to hci_connect function.
Instead of searching the address type in advertising cache, we
use the dst_type parameter to establish LE connections.
The dst_type is ignored for BR/EDR connection establishment.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Acked-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
As most LE devices leave advertising mode when they enter the connected
state, we may want to "pass" that connection to other users.
The first user will be the pairing procedure, the connection is
established without an associated socket, after the pairing is
complete, userspace may want to discover via GATT what services the
newly bonded device has.
If userspace establishes the connection while the timeout still
hasn't expired, the connection will be re-used.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Tested-by: João Paulo Rechi Vita <jprvita@openbossa.org>
Signed-off-by: Gustavo Padovan <gustavo@padovan.org>
The cid or psm and the source address might not be enough to uniquely
identify a global channel, especially when the source address is our
own.
For instance, when trying to communicate with two LE devices in master
mode, data received from the both devices is sent to the same socket.
Fix this by taking the destination address into account when choosing
the socket.
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Tested-by: João Paulo Rechi Vita <jprvita@openbossa.org>
Signed-off-by: Gustavo Padovan <gustavo@padovan.org>
SMP Keys should only be distributeed when encryption is successful.
Signed-off-by: Hemant Gupta <hemant.gupta@stericsson.com>
Signed-off-by: Gustavo Padovan <gustavo@padovan.org>
These functions encode or decode ERTM control fields (extended or
enhanced) to or from the new l2cap_ctrl structure.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Acked-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
A sequence list is a data structure used to track frames that need to
be retransmitted, and frames that have been requested for
retransmission by the remote device. It can compactly represent a
list of sequence numbers within the ERTM transmit window. Memory for
the list is allocated once at connection time, and common operations
in ERTM are O(1).
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Some parameters in L2CAP chan are set to default similar way in
socket based channels and A2MP channels. Adds common function which
sets all defaults.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo@padovan.org>
Following the separation if core and sock code this change avoid
manipulation of sk inside l2cap_chan_create().
Signed-off-by: Gustavo Padovan <gustavo@padovan.org>
Remove sparse warnings below:
...
net/bluetooth/l2cap_core.c:302:6: warning: symbol '__l2cap_chan_add' was
not declared. Should it be static?
net/bluetooth/l2cap_core.c:351:6: warning: symbol 'l2cap_chan_add' was
not declared. Should it be static?
...
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo@padovan.org>
In L2CAP we use le16 format so change direction of conversion
from le16_to_cpu to cpu_to_le16.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Create Chan Rsp shall put result and status in le format.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
L2CAP channel id is used in host format in internal L2CAP code.
Fix sparse warnings about wrong endian conversion.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
cmd->len is in le format so convert it to host format before use.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
chan->psm is kept in __le16 format which was not always taken
into account. Fix several bugs related to extra conversion.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Remove all #inclusions of asm/system.h preparatory to splitting and killing
it. Performed with the following command:
perl -p -i -e 's!^#\s*include\s*<asm/system[.]h>.*\n!!' `grep -Irl '^#\s*include\s*<asm/system[.]h>' *`
Signed-off-by: David Howells <dhowells@redhat.com>
When we queue delayed work we hold(chan) and delayed work
shall put(chan) after execution.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo@padovan.org>
The L2CAP timeout constants are always used in form of jiffies. So just
include the conversion from msecs in the define itself. This has the
advantage of making the code where the timeout is used more readable.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Fixed channel mask needs to be stored to decide whether to
use A2MP for example. So far save only one relevant byte which
keeps all information we need.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
sk_buffs should be freed using kfree_skb().
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The same sequence sending L2CAP Connection Request was used in several
places. Using subroutine makes those places easy to read.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Reviewed-by: Ulisses Furquim <ulisses@profusion.mobi>
Acked-by: Gustavo F. Padovan <padovan@profusion.mobi>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Change sk lock to chan lock in l2cap core and move sk locks
to l2cap sock code. bh_locks were used because of being RCU
critical section. When needed use explicit socket locks.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Reviewed-by: Ulisses Furquim <ulisses@profusion.mobi>
Acked-by: Gustavo F. Padovan <padovan@profusion.mobi>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Add unlocked L2CAP channel add function. Unlocked version will
be used in later patches.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Reviewed-by: Ulisses Furquim <ulisses@profusion.mobi>
Acked-by: Gustavo F. Padovan <padovan@profusion.mobi>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Use locked and unlocked versions to help removing socket
locks from l2cap core functions.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Reviewed-by: Ulisses Furquim <ulisses@profusion.mobi>
Acked-by: Gustavo F. Padovan <padovan@profusion.mobi>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Split to locked and unlocked versions of l2cap_state_change helping
to remove socket locks from l2cap code.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Reviewed-by: Ulisses Furquim <ulisses@profusion.mobi>
Acked-by: Gustavo F. Padovan <padovan@profusion.mobi>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Channel lock will be used to lock L2CAP channels which are locked
currently by socket locks.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Reviewed-by: Ulisses Furquim <ulisses@profusion.mobi>
Acked-by: Gustavo F. Padovan <padovan@profusion.mobi>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Usage of RCU list looks not reasonalbe for a number of reasons:
our code sleep and we had to use socket spinlocks. Most parts
of code are updaters thus there is little sense to use RCU.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Reviewed-by: Ulisses Furquim <ulisses@profusion.mobi>
Acked-by: Gustavo F. Padovan <padovan@profusion.mobi>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Several hex numbers were printed without object name which
complicates debugging.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Use state_to_string function in debug statements.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Function state_to_string will be used in other files in debug
statements.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Pending I-Frame(s) are considered as acknowledgement. To void double
acking (via I-Frame and later via RR) clear ack timer when sending
first pending I-Frame.
Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Make l2cap_ertm_send return number of pending I-Frames transmitted
instead of all (pending + retransmitted) I-Frames transmitted.
As only pending I-Frames are considered as acknowledgement, this could
lead to situation when no ACK was sent in __l2cap_send_ack (if only
already transmitted I-Frames were retransmitted).
Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Acked-by: Gustavo F. Padovan <padovan@profusion.mobi>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
In debug use chan %p instead of sk.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Change elseif to switch. This make sense even more with following
patches which otherwise have to add more elseifs statements.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Change is needed to remove dependency on sk when possible
before introducing l2cap channel lock.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
We need to use the _sync() version for cancelling the info and security
timer in the L2CAP connection delete path. Otherwise the delayed work
handler might run after the connection object is freed.
Signed-off-by: Ulisses Furquim <ulisses@profusion.mobi>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
__cancel_delayed_work() is being used in some paths where we cannot
sleep waiting for the delayed work to finish. However, that function
might return while the timer is running and the work will be queued
again. Replace the calls with safer cancel_delayed_work() version
which spins until the timer handler finishes on other CPUs and
cancels the delayed work.
Signed-off-by: Ulisses Furquim <ulisses@profusion.mobi>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
It is not used outside of l2cap_core.c. Also l2cap_ertm_data_rcv is
only used after it is defined so there is no need for forward declaration.
Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
These flags can and will be used for more general purpose values than
just pending state transitions so the more common name "flags" makes
more sense than "pend".
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Remove unneeded conversion from sk to chan.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Reference counter was incremented when starting ack timer but
decremented only when clearing timer, not when timer fired.
Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
There is no need to send RNR immediately when entring local busy.
Also upper layer might clear local busy condition before ack timer
expires saving few cycles for sending RNR.
This also prevents sending two RNRs in some cases where sending one
would be enough i.e received N I-frame can trigger local busy
(sending RNR acking up to N-1 I-frame) and later sending ack (RNR
acking up to N I-frame).
This was affecting TC_ERM_BV_07_C and TC_ERM_BV_22_C with some non
default channel parameters (tx window and receiving buffer sizes).
Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
ack_timer should be cleared when sending ACK to avoid acking I-frames
twice.
This commit introduces helper function (only send ack, not clearing
timer) which is used by l2cap_send_ack and l2cap_ack_timeout. This is
to avoid clearing ack timer in timer function.
Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
SREJ frame with P-bit set acknowledges I-frames numbered up to
(ReqSeq - 1). With this patch P-bit in SREJ is set only when there are
some I-frames to ack.
This fixes ambiguous situation when lost of I-frame with TxSeq=0 would
result in sending SREJ acking all previous I-frames.
Consider following scenario:
TxWindow=3
HostA: sent I-frame TxSeq=0
HostA: sent I-frame TxSeq=1
HostA: sent I-frame TxSeq=2
HostB: missed I-frame TxSeq=0
HostB: received I-frame TxSeq=1
HostB: sent SREJ ReqSeq=0 Pbit=1
HostA: received SREJ ReqSeq=0 Pbit=1 <- All I-frames acked or not?
...
Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
As reported by Dan Carpenter this function causes a Sparse warning and
shouldn't be declared inline:
include/net/bluetooth/l2cap.h:837:30 error: marked inline, but without a
definition"
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
After moving L2CAP timers to workqueues l2cap_set_timer expects timeout
value to be specified in jiffies but constants defined in miliseconds
are used. This makes timeouts unreliable when CONFIG_HZ is not set to
1000.
__set_chan_timer macro still uses jiffies as input to avoid multiple
conversions from/to jiffies for sk_sndtimeo value which is already
specified in jiffies.
Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@tieto.com>
Ackec-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Those locks are not shared between interrupt and process context anymore,
so remove the part that disable interrupts. We are still safe because
preemption is disabled.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
It should be the dst in the copy not src. 03a001948 introduced this bug.
Reported-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Conflicts:
net/bluetooth/l2cap_core.c
Just two overlapping changes, one added an initialization of
a local variable, and another change added a new local variable.
Signed-off-by: David S. Miller <davem@davemloft.net>
The struct hci_proto and all related register/unregister and dispatching
code was removed. HCI core code now call directly the SCO and L2CAP
event functions.
Signed-off-by: Ulisses Furquim <ulisses@profusion.mobi>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
It makes more sense this way, since info_timer is a timer using delayed
work API.
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This one also needs to run in process context
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
module_param(bool) used to counter-intuitively take an int. In
fddd5201 (mid-2009) we allowed bool or int/unsigned int using a messy
trick.
It's time to remove the int/unsigned int option. For this version
it'll simply give a warning, but it'll break next kernel version.
(Thanks to Joe Perches for suggesting coccinelle for 0/1 -> true/false).
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
When configuring an ERTM or streaming mode connection, remote devices
are expected to send an RFC option in a successful config response. A
misbehaving remote device might not send an RFC option, and the L2CAP
code should not access uninitialized data in this case.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This list has much more reads than writes, so RCU makes senses here, also
it avoid deadlock against the socket lock.
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This move some checking code that was in l2cap_sock_connect() to
l2cap_chan_connect(). Thus we can invert the lock calls, i.e., call
lock_sock() before hci_dev_lock() to avoid a deadlock scenario.
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Another step of remove interrupt context from Bluetooth Core.
Use the system workqueue.
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
spin lock doesn't fit ok anymore on the new code based on workqueues.
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
We run everything in the same lock now. The backlog queue is useless now
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
We now run everything in process context, so the mutex lock is the best
option. But in some places we still need the bh_lock_sock()
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
L2CAP timers also need to run in process context. As the works in l2cap
are small we are using the system worqueue.
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Now we run everything in HCI in process context, so it's a better idea use
mutex instead spin_lock. The macro remains hci_dev_lock() (and I got rid
of hci_dev_lock_bh()), of course.
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
I did this as a part of a testing course at university, but it might be
useful upstream as well.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Fixes bluetooth compiling when CONFIG_BT_L2CAP is not enabled
net/built-in.o: In function `hci_dev_open':
(.text+0xdce9a): undefined reference to `enable_hs'
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Make __l2cap_global_chan_by_addr similar to other find functions.
Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This make it easier to see what is the real reason for loop to exit.
skb_queue_next return valid skb or garbage, not NULL.
Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Make it easier to see what is loop break condition.
skb_queue_next return valid skb or garbage, not NULL.
Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Due to ERTM reliability L2CAP channel needs to be disconnected if
adding to srej list failed.
Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
rename to l2cap_chan_check_security() to make it consistent with other
l2cap_exported functions. This function will be exported in a later
commit.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Add parsing Extended Flow Specification in L2CAP Config Response.
Based upon haijun.liu <haijun.liu@atheros.com> series of patches
(sent Sun, 22 Aug 2010)
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
AMP channels can be moved between BR/EDR and AMP controllers using a
sequence of signals. Every attempted channel move involves a series of
four signals:
Move Initiator Move Responder
| |
| Move Channel Request |
| ----------------------------> |
| |
| Move Channel Response |
| <---------------------------- |
| |
| Move Channel Confirm |
| ----------------------------> |
| |
| Move Channel Confirm Response |
| <---------------------------- |
All four signals are sent even if the move fails.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Acked-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
The A2MP fixed channel bit is only set when high-speed mode is enabled.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Acked-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This implement priority based scheduler using skbuffer priority set via
SO_PRIORITY socket option.
It introduces hci_chan_hash (list of HCI Channel/hci_chan) per connection,
each item in this list refer to a L2CAP connection and it is used to
queue the data for transmission.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This uses SO_PRIORITY to set the skbuffer priority field
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
l2cap_set_timer function prints sk instead of chan pointer.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
make code readable by removing magic numbers
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Timers set by __set_chan_timer() should use miliseconds instead of
jiffies. Commit 942ecc9c46 updated
l2cap_set_timer() so it expects timeout to be specified in msecs
instead of jiffies. This makes timeouts unreliable when CONFIG_HZ
is not set to 1000.
Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@tieto.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Add parsing Extended Flow Specification option in L2CAP Config Request
Based upon haijun.liu <haijun.liu@atheros.com> series of patches
(sent Sun, 22 Aug 2010)
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Fix max_pdu_size calculationin for RFC. Change magic number to human readable
defines.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Remove magic numbers for FCS, SDU LEN and PSM LEN
when calculating packet payload.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Adds support for extended sequence numbers found in
extended control fields.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
There are three different Control Field formats: the Standard Control
Field, the Enhanced Control Field, and the Extended Control Field.
Patch adds function to handle all those fields seamlessly.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Recalculate length of L2CAP header based on Control field length.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Handle POLL (P) bit in L2CAP ERTM using information about control field type.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Handle final (F) bit in L2CAP using information about control field type.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Check frame function uses now information about control field type.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
L2CAP ERTM txseq calculation uses now information about control field type.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
reqseq calculation uses now information about control field type.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Segmentation and Reassembly (SAR) occupies different windows in standard and
extended control fields. Convert hardcoded masks to relative ones and use shift
to access SAR bits.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Supervisory bits occupy different windows in standard / extended control
fields. Convert hardcoded masks to relative ones and use shift to access
S-bit window.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Adds support for extended window size (EWS) config option. We enable EWS
feature in L2CAP Info RSP when hs enabled. EWS option is included in L2CAP
Config Req if tx_win (which is set via socket) bigger then standard default
value (63) && hs enabled && remote side supports EWS feature.
Using EWS selects extended control field in L2CAP.
Code partly based on Qualcomm and Atheros patches sent upstream a year ago.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
role_switch variable inside l2cap_chan is a logical one and can
be easily converted to flag
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
force_active variable inside l2cap_chan is a logical one and can
be easily converted to flag
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
force_reliable variable inside l2cap_chan is a logical one and can
be easily converted to flag
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
flushable variable inside l2cap_chan is a logical one and can
be easily converted to flag. Added flags in l2cap_chan structure.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Add enable_hs kernel parameter. L2CAP_FEAT_EXT_FLOW depends on it.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Use sk_buff fragment capabilities to link together incoming skbs
instead of allocating a new skb for reassembly and copying.
The new reassembly code works equally well for ERTM and streaming
mode, so there is now one reassembly function instead of two.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
l2cap_create_iframe_pdu is only used in l2cap_core.c
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
The function crypto_blkcipher_setkey() called by smp_e()
can sleep, so all the crypto work has to be moved to
hci_dev workqueue.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
When doing the pairing procedure we won't have an associated
socket, but we still have to do the SMP negotiation. This
adds support for encrypting the link and exchanging keys.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Add HCI_CONN_LE_SMP_PEND flag to indicate that SMP is pending
for that connection. This allows to have information that an SMP
procedure is going on for that connection.
We use the HCI_CONN_ENCRYPT_PEND to indicate that encryption
(HCI_LE_Start_Encryption) is pending for that connection.
While a SMP procedure is going on we hold an reference to the
connection, to avoid disconnections.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Fix race condition which can result in missing wakeup during
l2cap socket shutdown.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Another regression fix considering incomming l2cap connections with
defer_setup enabled. In situations when incomming connection is
extracted with l2cap_sock_accept, it's bt_sock info will have
'parent' member zerroed, but 'parent' may be used unconditionally
in l2cap_conn_start() and l2cap_security_cfm() when defer_setup
is enabled.
Backtrace:
[<bf02d5ac>] (l2cap_security_cfm+0x0/0x2ac [bluetooth]) from [<bf01f01c>] (hci_event_pac
ket+0xc2c/0x4aa4 [bluetooth])
[<bf01e3f0>] (hci_event_packet+0x0/0x4aa4 [bluetooth]) from [<bf01a844>] (hci_rx_task+0x
cc/0x27c [bluetooth])
[<bf01a778>] (hci_rx_task+0x0/0x27c [bluetooth]) from [<c008eee4>] (tasklet_action+0xa0/
0x15c)
[<c008ee44>] (tasklet_action+0x0/0x15c) from [<c008f38c>] (__do_softirq+0x98/0x130)
r7:00000101 r6:00000018 r5:00000001 r4:efc46000
[<c008f2f4>] (__do_softirq+0x0/0x130) from [<c008f524>] (do_softirq+0x4c/0x58)
[<c008f4d8>] (do_softirq+0x0/0x58) from [<c008f5e0>] (run_ksoftirqd+0xb0/0x1b4)
r4:efc46000 r3:00000001
[<c008f530>] (run_ksoftirqd+0x0/0x1b4) from [<c009f2a8>] (kthread+0x84/0x8c)
r7:00000000 r6:c008f530 r5:efc47fc4 r4:efc41f08
[<c009f224>] (kthread+0x0/0x8c) from [<c008cc84>] (do_exit+0x0/0x5f0)
Signed-off-by: Ilia Kolomisnky <iliak@ti.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Caused by the following commit, partially revert it.
commit 9fa7e4f76f
Author: Gustavo F. Padovan <padovan@profusion.mobi>
Date: Thu Jun 30 16:11:30 2011 -0300
Bluetooth: Fix regression with incoming L2CAP connections
PTS test A2DP/SRC/SRC_SET/TC_SRC_SET_BV_02_I revealed that
( probably after the df3c3931e commit ) the l2cap connection
could not be established in case when the "Auth Complete" HCI
event does not arive before the initiator send "Configuration
request", in which case l2cap replies with "Command rejected"
since the channel is still in BT_CONNECT2 state.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Signed-off-by: David S. Miller <davem@davemloft.net>
There can 3 reasons for the "command reject" reply produced
by the stack. Each such reply should be accompanied by the
relevand data ( as defined in spec. ). Currently there is one
instance of "command reject" reply with reason "invalid cid"
wich is fixed. Also, added clean-up definitions related to the
"command reject" replies.
Signed-off-by: Ilia Kolomisnky <iliak@ti.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This adds support for generating and distributing all the keys
specified in the third phase of SMP.
This will make possible to re-establish secure connections, resolve
private addresses and sign commands.
For now, the values generated are random.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
The ERTM receive buffer is now handled in a way that does not require
the busy queue and the associated polling code.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This change moves most L2CAP ERTM receive buffer handling out of the
L2CAP core and in to the socket code. It's up to the higher layer
(the socket code, in this case) to tell the core when its buffer is
full or has space available. The recv op should always accept
incoming ERTM data or else the connection will go down.
Within the socket layer, an skb that does not fit in the socket
receive buffer will be temporarily stored. When the socket is read
from, that skb will be placed in the receive buffer if possible. Once
adequate buffer space becomes available, the L2CAP core is informed
and the ERTM local busy state is cleared.
Receive buffer management for non-ERTM modes is unchanged.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
The local busy state is entered and exited based on buffer status in
the socket layer (or other upper layer). This change is in
preparation for general buffer status reports from the socket layer,
which will then be used to change the local busy status.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Even when the received tx_seq is expected, the frame still needs to be
dropped if the TX window is exceeded or the receiver is in the local
busy state.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Make it easier to use more normal logging styles later.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
ERTM timeouts are defined in milliseconds, but need to be converted
to jiffies when passed to mod_timer().
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
PTS test A2DP/SRC/SRC_SET/TC_SRC_SET_BV_02_I revealed that
( probably after the df3c3931e commit ) the l2cap connection
could not be established in case when the "Auth Complete" HCI
event does not arive before the initiator send "Configuration
request", in which case l2cap replies with "Command rejected"
since the channel is still in BT_CONNECT2 state.
Based on patch from: Ilia Kolomisnky <iliak@ti.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
A remote user can provide a small value for the command size field in
the command header of an l2cap configuration request, resulting in an
integer underflow when subtracting the size of the configuration request
header. This results in copying a very large amount of data via
memcpy() and destroying the kernel heap. Check for underflow.
Signed-off-by: Dan Rosenberg <drosenberg@vsecurity.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
When the connection is ready we should set the connection
to CONNECTED so userspace can use it.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
We already have access to the chan, we don't have to access the
socket to get its imtu.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
We should not try to do any other type of configuration for
LE links when they become ready.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Instead of setting bits manually we use set_bit, test_bit, etc.
Also remove L2CAP_ prefix from macros.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This patch adds support for disconnecting the link when SMP procedure
takes more than 30 seconds.
SMP begins when either the Pairing Request command is sent or the
Pairing Response is received, and it ends when the link is encrypted
(or terminated). Vol 3, Part H Section 3.4.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
When authentication completes we shouldn't blindly accept any pending
L2CAP connect requests. If the socket has the defer_setup feature
enabled it should still wait for user space acceptance of the connect
request. The issue only happens for non-SSP connections since with SSP
the L2CAP Connect request may not be sent for non-SDP PSMs before
authentication has completed successfully.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This adds support for resuming the user space traffic when SMP
negotiation is complete.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Start SMP procedure for LE connections. This modification intercepts
l2cap received frames and call proper SMP functions to start the SMP
procedure. By now, no keys are being used.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: Anderson Briglia <anderson.briglia@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Andrei Emeltchenko