Add a narration to i915.rst about Intel GEN GPU's: engines,
driver context and relocation. Also do minor reorder to improve
narration.
v5:
More type fixes.
Flow bullet list so lines are not too long.
Signed-off-by: Kevin Rogovin <kevin.rogovin@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
[Joonas: correcting the patch title]
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1523001957-6427-2-git-send-email-kevin.rogovin@intel.com
We don't handle resetting the kernel context very well, or presumably any
context executing its breadcrumb commands in the ring as opposed to the
batchbuffer and flush. If we trigger a device reset twice in quick
succession while the kernel context is executing, we may end up skipping
the breadcrumb. This is really only a problem for the selftest as
normally there is a large interlude between resets (hangcheck), or we
focus on resetting just one engine and so avoid repeatedly resetting
innocents.
Something to try would be a preempt-to-idle to quiesce the engine before
reset, so that innocent contexts would be spared the reset.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Michał Winiarski <michal.winiarski@intel.com>
CC: Michel Thierry <michel.thierry@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180330131801.18327-1-chris@chris-wilson.co.uk
On Apollolake, with stress test warm reboot, audio card was not getting
enumerated after reboot. This was a spurious issue happening on
Apollolake. HW codec and HD audio controller link was going out of sync
for which there was a fix in i915 driver but was not getting invoked for
BXT. Extending this fix to BXT as well.
Tested on apollolake chromebook by stress test warm reboot with 2500
iterations.
Bspec: 21829
Signed-off-by: Gaurav K Singh <gaurav.k.singh@intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1522946544-11524-1-git-send-email-gaurav.k.singh@intel.com
If we skip the intel_prepare_reset(), we should also skip the
intel_display_reset(). If we we use a flag set by intel_prepare_reset()
then we do not have to second guess based on external user controlled
state whether or not the prepare was called before deciding to finish
it after the reset. igt/gem_eio is one such example that may tweak
i915.reset faster than the code is expecting, leading to
[ 190.233528] =====================================
[ 190.233534] WARNING: bad unlock balance detected!
[ 190.233540] 4.16.0-rc7-g335ef9849310-drmtip_10+ #1 Tainted: G U
[ 190.233547] -------------------------------------
[ 190.233553] gem_eio/1348 is trying to release lock (crtc_ww_class_acquire) at:
[ 190.233569] [<ffffffff895c7810>] drm_modeset_acquire_fini+0x0/0x60
[ 190.233575] but there are no more locks to release!
[ 190.233580]
other info that might help us debug this:
[ 190.233588] 3 locks held by gem_eio/1348:
[ 190.233592] #0: (&f->f_pos_lock){+.+.}, at: [<00000000ab90c784>] __fdget_pos+0x3a/0x50
[ 190.233607] #1: (sb_writers#11){.+.+}, at: [<00000000e1529265>] vfs_write+0x188/0x1a0
[ 190.233622] #2: (&attr->mutex){+.+.}, at: [<0000000011f40afe>] simple_attr_write+0x36/0xd0
[ 190.233635]
stack backtrace:
[ 190.233644] CPU: 0 PID: 1348 Comm: gem_eio Tainted: G U 4.16.0-rc7-g335ef9849310-drmtip_10+ #1
[ 190.233655] Hardware name: Dell Inc. OptiPlex GX280 /0G8310, BIOS A04 02/09/2005
[ 190.233664] Call Trace:
[ 190.233674] dump_stack+0x67/0x95
[ 190.233682] ? drm_modeset_backoff+0x1b0/0x1b0
[ 190.233690] print_unlock_imbalance_bug+0xd2/0xe0
[ 190.233698] ? drm_modeset_backoff+0x1b0/0x1b0
[ 190.233704] lock_release+0x23e/0x300
[ 190.233712] drm_modeset_acquire_fini+0x16/0x60
[ 190.233835] intel_finish_reset+0x72/0x160 [i915]
[ 190.233894] i915_reset_device+0x1e9/0x240 [i915]
[ 190.233953] ? __intel_get_crtc_scanline+0x1c0/0x1c0 [i915]
[ 190.233962] ? work_on_cpu_safe+0x50/0x50
[ 190.234020] i915_handle_error+0x1f2/0x470 [i915]
[ 190.234031] ? __might_fault+0x39/0x90
[ 190.234037] ? __might_fault+0x39/0x90
[ 190.234099] i915_wedged_set+0x7f/0xc0 [i915]
[ 190.234107] simple_attr_write+0xb0/0xd0
[ 190.234117] full_proxy_write+0x51/0x80
[ 190.234125] __vfs_write+0x21/0x140
[ 190.234133] ? rcu_read_lock_sched_held+0x6f/0x80
[ 190.234140] ? rcu_sync_lockdep_assert+0x29/0x50
[ 190.234147] ? __sb_start_write+0x152/0x1f0
[ 190.234152] ? __sb_start_write+0x168/0x1f0
[ 190.234159] vfs_write+0xbd/0x1a0
[ 190.234166] SyS_write+0x40/0xa0
[ 190.234173] ? do_syscall_64+0x19/0x1b0
[ 190.234180] do_syscall_64+0x6b/0x1b0
[ 190.234188] entry_SYSCALL_64_after_hwframe+0x42/0xb7
[ 190.234196] RIP: 0033:0x7f84c1b392b7
[ 190.234201] RSP: 002b:00007f84b6755b00 EFLAGS: 00000293 ORIG_RAX: 0000000000000001
[ 190.234211] RAX: ffffffffffffffda RBX: 0000000000000046 RCX: 00007f84c1b392b7
[ 190.234218] RDX: 0000000000000002 RSI: 000055ec20abc8d6 RDI: 0000000000000046
[ 190.234225] RBP: 000055ec20abc8d6 R08: 0000000000000000 R09: 0000000000000000
[ 190.234231] R10: 0000000000000000 R11: 0000000000000293 R12: 0000000000000002
[ 190.234238] R13: 0000000000000000 R14: 00007f84b0000b20 R15: 000055ec20ce4eb8
Testcase: igt/gem_eio
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180405123714.3638-1-chris@chris-wilson.co.uk
Before adding a new feature to execlists submission, we should endeavour
to cover the baseline behaviour with selftests. So start the ball
rolling.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michał Winiarski <michal.winiarski@intel.com>
CC: Michel Thierry <michel.thierry@intel.com>
Cc: Jeff McGee <jeff.mcgee@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180404093329.5383-1-chris@chris-wilson.co.uk
Along the eb_lookup_vmas() error path, the return value from
kmem_cache_alloc() was freed using kfree(). Fix it to use the proper
kmem_cache_free() instead.
Fixes: d1b48c1e71 ("drm/i915: Replace execbuf vma ht with an idr")
Signed-off-by: Xidong Wang <wangxidong_97@163.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: <stable@vger.kernel.org> # v4.14+
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180404093824.9313-1-chris@chris-wilson.co.uk
HDCP1.4 key can be loaded, only when Power well #1 is enabled and cdclk
is enabled. Using the I915 power well infrastruture, above requirement
is verified.
This patch enables the hdcp initialization for HSW, BDW, and BXT.
v2:
Choose the PW# based on the platform.
v3:
No Changes.
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1522663834-24482-4-git-send-email-ramalingam.c@intel.com
In case of V prime mismatch, DP HDCP spec mandates the re-read of
Vprime atleast twice.
This patch needed for DP HDCP1.4 CTS Test: 1B-05.
v2:
Moved the V' validation into a function for retry. [Sean Paul]
v3:
Removed Inline keyword and DRM_DEBUG_KMS are used [Sean Paul]
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1522663834-24482-3-git-send-email-ramalingam.c@intel.com
As per DP spec when R0 mismatch is detected, HDCP source supported
re-read the R0 atleast twice.
And For HDMI and DP minimum wait required for the R0 availability is
100mSec. So this patch changes the wait time to 100mSec but retries
twice with the time interval of 100mSec for each attempt.
This patch is needed for DP HDCP1.4 CTS Test: 1A-06.
v2:
No Change
v3:
Comment on R0 retry is moved closer to the code[Seanpaul]
v4:
Removing unwanted noise introduced in v3.
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1522669822-2508-1-git-send-email-ramalingam.c@intel.com
Let's avoid having to delve down the pointer chain to see if the i915
device has support for preemption and store that on the engine, which
made the decision in the first place!
v2: Refactor common preemption policy between execlists/guc.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tomasz Lis <tomasz.lis@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180403183537.5522-1-chris@chris-wilson.co.uk
We would like to start doing some bookkeeping at the beginning, between
contexts and at the end of execlists submission. We already mark the
beginning and end using EXECLISTS_ACTIVE_USER, to provide an indication
when the HW is idle. This give us a pair of sequence points we can then
expand on for further bookkeeping.
v2: Refactor guc submission to share the same begin/end.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Francisco Jerez <currojerez@riseup.net>
Reviewed-by: Francisco Jerez <currojerez@riseup.net>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180331130626.10712-1-chris@chris-wilson.co.uk
Commit 'aee3bac0a3a8 ("drm/i915/psr: Tie PSR2 support to Y
coordinate requirement")' got merged to drm-intel-next-queued
but the variable was defined commit 'c5fe47327b06 ("drm: Add PSR
version 3 macro") who was merged through drm-misc.
So backmerging to get drm-intel-next-queued compiling back again.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
In the 2 eDP1.4a pannels tested set or not set bit have no effect
but is better set it and comply with specification.
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180328223046.16125-9-jose.souza@intel.com
This value do not change overtime so better cache it than
fetch it every PSR enable.
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180328223046.16125-8-jose.souza@intel.com
Sink can support our PSR2 requirements but userspace can request
a resolution that PSR2 hardware do not support, in this case it
was overwritten the PSR2 sink support.
Adding another flag here, this way if requested resolution changed
to a value that PSR2 hardware can handle, PSR2 can be enabled.
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180328223046.16125-6-jose.souza@intel.com
For Geminilake and Cannonlake+ the Y-coordinate support must be
enabled in PSR2_CTL too.
Spec: 7713 and 7720
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180328223046.16125-5-jose.souza@intel.com
Although i915 don't implement aux sync frame through tests was
findout that pannels can do selective update when the y-coordinate
is also included in SDP, that is why it is required to run PSR2 in
i915.
So moving to only one place the sink requirements that the actual
driver needs to enable PSR2.
Also intel_psr2_config_valid() is called every time the crtc config
is computed, wasting some time every time it was checking for
Y coordinate requirement.
This allow us to nuke y_cord_support and some of VSC setup code that
was handling a scenario that would never happen(PSR2 without Y
coordinate).
Also here renaming intel_dp_get_y_cord_status() to
intel_dp_get_y_coord_required() as it more accurate to the name and
function of bit according to eDP spec.
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180328223046.16125-4-jose.souza@intel.com
eDP spec states that aux frame is required to do PSR2 selective
update but i915 don't fully implement it. It sends the aux frame
sync messages but the value is always zero as the GTC is not enabled
in driver.
Through tests was findout that pannels can do selective update when
the y-coordinate is also included in SDP, that is why it is required
to run PSR2 in i915.
A dummy value is not useful at all to sink, so removing everything
related to aux frame sync, if GTC is enabled we can bring this back.
Cc: Vathsala Nagaraju <vathsala.nagaraju@intel.com>
Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180328223046.16125-3-jose.souza@intel.com
As intel_wait_for_register_fw() may use, and if successful only use, a
busy-wait loop, the might_sleep() warning is a little over-zealous.
Restrict it to a might_sleep_if() a slow timeout is specified (and so
the caller authorises use of a usleep).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180329224519.13598-2-chris@chris-wilson.co.uk
Only sleep and repeat when asked for a full device reset (ALL_ENGINES)
and avoid using sleeping waits when asked for a per-engine reset. The
goal is to be able to use a per-engine reset from hardirq/softirq/timer
context. A consequence is that our individual wait timeouts are a
thousand times shorter, on the order of a hundred microseconds rather
than hundreds of millisecond. This may make hitting the timeouts more
common, but hopefully the fallover to the full-device reset will be
sufficient to pick up the pieces.
Note, that the sleeps inside older gen (pre-gen8) have been left as they
are only used in full device reset mode.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Michał Winiarski <michal.winiarski@intel.com>
CC: Michel Thierry <michel.thierry@intel.com>
Cc: Jeff McGee <jeff.mcgee@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180329224519.13598-1-chris@chris-wilson.co.uk
In commit d79651522e ("drm/i915: Enable i915 perf stream for
Haswell OA unit") the enable/disable vfunc hadn't appear yet and the
same function would deal with enabling/disabling the OA unit.
This was split later on for gen8 but the gen7 retained some code that
isn't actually useful anymore.
Signed-off-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180326090831.22686-4-lionel.g.landwerlin@intel.com
Probably lost while rebasing commit eacd8391f9 ("drm/i915/guc: Keep GuC
interrupts enabled when using GuC").
Not really needed since i915_gem_init_hw is called before uc_resume, but
it brings symmetry to uc_suspend.
Signed-off-by: Michel Thierry <michel.thierry@intel.com>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Reviewed-by: Michał Winiarski <michal.winiarski@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180328205851.16188-1-michel.thierry@intel.com
- Mask mode type garbage from userspace (Ville)
Something went wrong on the misc tree side, but I'll pull the patch directly.
* 'drm-misc-next-fixes' of git://anongit.freedesktop.org/drm/drm-misc:
drm: Fix uabi regression by allowing garbage mode->type from userspace
During debug we may want to investigate all communication
from the Guc. Add proper tracing macros in debug config.
v2: convert remaining DRM_DEBUG into new CT_DEBUG (Michal)
v3: use dedicated Kconfig (Daniele)
v4: checkpatch
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180326194829.58836-12-michal.wajdeczko@intel.com
When running on platform with CTB based GuC communication enabled,
GuC to Host event data will be delivered as CT request message.
However, content of the data[1] of this CT message follows format
of the scratch register used in MMIO based communication, so some
code reuse is still possible.
v2: filter disabled messages (Daniele)
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Oscar Mateo <oscar.mateo@intel.com>
Reviewed-by: Michel Thierry <michel.thierry@intel.com> #1
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Acked-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180327214124.70680-1-michal.wajdeczko@intel.com
Requests are read from CT in the irq handler, but actual processing
will be done in the work thread. Processing of specific actions will
be added in the upcoming patches.
v2: don't use GEM_BUG_ON (Chris)
don't kmalloc too large buffer (Michal)
v3: rebased
v4: don't name it 'dispatch' (Michel) and fix checkpatch
add some documentation (Michal)
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Oscar Mateo <oscar.mateo@intel.com>
Cc: Michel Thierry <michel.thierry@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180326194829.58836-10-michal.wajdeczko@intel.com
Instead of returning small data in response status dword,
GuC may append longer data as response message payload.
If caller provides response buffer, we will copy received
data and use number of received data dwords as new success
return value. We will WARN if response from GuC does not
match caller expectation.
v2: fix timeout and checkpatch warnings (Michal)
v3: fix checkpatch again (Michel)
update wait function name (Michal)
no need for spinlock_irqsave (MichalWi)
no magic numbers (MichalWi)
must check before use (Jani)
add some more documentation (Michal)
v4: update documentation (Michal)
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Oscar Mateo <oscar.mateo@intel.com>
Cc: Michel Thierry <michel.thierry@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Reviewed-by: Michel Thierry <michel.thierry@intel.com> #2.5
Cc: Michal Winiarski <michal.winiarski@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180327121439.70096-1-michal.wajdeczko@intel.com
In next patch we will introduce another way of waiting for the response
that will use RECV buffer. To avoid misleading names, rename old wait
function to reflect the fact that it is based on descriptor update.
v2: fix comment style (Michal)
v3: use more specific name (Michel)
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180326194829.58836-8-michal.wajdeczko@intel.com
GuC can respond to our commands not only by updating SEND buffer
descriptor, but can also send a response message over RECV buffer.
Guc can also send unsolicited request messages over RECV buffer.
Let's start reading those messages and make placeholders
for actual response/request handlers.
v2: misc improvements (Michal)
v3: change response detection (Michal)
invalid status is protocol error (Michal)
v4: rebase
v5: fix checkpatch (Michel)
don't use fields before check (Jani)
add some documentation (Michal)
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Oscar Mateo <oscar.mateo@intel.com>
Cc: Michel Thierry <michel.thierry@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Reviewed-by: Michel Thierry <michel.thierry@intel.com> # 4.5
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180326194829.58836-7-michal.wajdeczko@intel.com
On platforms with CTB based GuC communications, we will handle
GuC events in a different way. Let's make event handler a virtual
function to allow easy switch between those variants.
Credits-to: Oscar Mateo <oscar.mateo@intel.com>
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Oscar Mateo <oscar.mateo@intel.com>
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180326194829.58836-6-michal.wajdeczko@intel.com
We're using data encoded in the status MMIO as return value from send
function, but GuC may also write more data in remaining MMIO regs.
Let's copy content of these registers to the buffer provided by caller.
v2: new line (Michel)
v3: updated commit message
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Oscar Mateo <oscar.mateo@intel.com>
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180326194829.58836-5-michal.wajdeczko@intel.com
This is a preparation step for the upcoming patches.
We already can return some small data decoded from the command
status, but we will need more in the future.
v2: add explicit response buf size
v3: squash with helper patch
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Oscar Mateo <oscar.mateo@intel.com>
Cc: Michel Thierry <michel.thierry@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180326194829.58836-4-michal.wajdeczko@intel.com
GuC may return additional data in the response message.
Format and meaning of this data is action specific. We will
use this non-negative data as a new success return value.
Currently used actions don't return data that way yet.
v2: fix prohibited space after '~' (Michel)
update commit message (Daniele)
v3: rebase
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Oscar Mateo <oscar.mateo@intel.com>
Cc: Michel Thierry <michel.thierry@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180326194829.58836-3-michal.wajdeczko@intel.com
As we are going to extend our use of MMIO based communication,
try to explain its mechanics and update corresponding definitions.
v2: fix checkpatch MACRO_ARG_REUSE
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Cc: Kelvin Gardiner <kelvin.gardiner@intel.com>
Reviewed-by: Michel Thierry <michel.thierry@intel.com> #1
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180326194829.58836-2-michal.wajdeczko@intel.com
Tvrtko uncovered a fun issue with recovering from a wedge device. In his
tests, he wedged the driver by injecting an unrecoverable hang whilst a
batch was spinning. As we reset the gpu in the middle of the spinner,
when resumed it would continue on from the next instruction in the ring
and write it's breadcrumb. However, on wedging we updated our
bookkeeping to indicate that the GPU had completed executing and would
restart from after the breadcrumb; so the emission of the stale
breadcrumb from before the reset came as a bit of a surprise.
A simple fix is to when rebinding the context into the GPU, we update
the ring register state in the context image to match our bookkeeping.
We already have to update the RING_START and RING_TAIL, so updating
RING_HEAD as well is trivial. This works because whenever we unbind the
context, we keep the bookkeeping in check; and on wedging we unbind all
contexts.
Testcase: igt/gem_eio
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180327210136.16750-1-chris@chris-wilson.co.uk
Tested-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
The only thing that differs here is that the crystal clock freq now
has four possible values.
This patch gets rid of the "Unknown gen, unable to compute..." message
at boot for gen11.
Reviewed-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180109232835.11478-18-paulo.r.zanoni@intel.com
GuC Address Space and WOPCM Layout diagrams won't be generated correctly by
sphinx build if not using proper reST syntax.
This patch uses reST literal blocks to make sure GuC Address Space and
WOPCM Layout diagrams to be generated correctly, and it also corrects some
errors in the diagram description.
v2:
- Fixed errors in diagram description
v3:
- Updated GuC Address Space kernel-doc based on Michal's suggestion
v4:
- Added WOPCM layout and GuC address space docs into i915.rst (Joonas)
Signed-off-by: Jackie Li <yaodong.li@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1521763162-11424-1-git-send-email-yaodong.li@intel.com
- GPUVM support for dGPUs
- KFD events support for dGPUs
- Fix live-lock situation when restoring multiple evicted processes
- Fix VM page table allocation on large-bar systems
- Fix for build failure on frv architecture
* tag 'drm-amdkfd-next-2018-03-27' of git://people.freedesktop.org/~gabbayo/linux:
drm/amdkfd: Use ordered workqueue to restore processes
drm/amdgpu: Fix acquiring VM on large-BAR systems
drm/amdkfd: Add module option for testing large-BAR functionality
drm/amdkfd: Kmap event page for dGPUs
drm/amdkfd: Add ioctls for GPUVM memory management
drm/amdkfd: Add TC flush on VMID deallocation for Hawaii
drm/amdkfd: Allocate CWSR trap handler memory for dGPUs
drm/amdkfd: Add per-process IDR for buffer handles
drm/amdkfd: Aperture setup for dGPUs
drm/amdkfd: Remove limit on number of GPUs
drm/amdkfd: Populate DRM render device minor
drm/amdkfd: Create KFD VMs on demand
drm/amdgpu: Add kfd2kgd interface to acquire an existing VM
drm/amdgpu: Add helper to turn an existing VM into a compute VM
drm/amdgpu: Fix initial validation of PD BO for KFD VMs
drm/amdgpu: Move KFD-specific fields into struct amdgpu_vm
drm/amdkfd: fix uninitialized variable use
drm/amdkfd: add missing include of mm.h
- Display fixes for booting with MST hub lid closed and display
freezing after hibernation (fd.o bugs 105470 & 105196)
- Fix for a very rare interrupt handling race resulting in GPU hang
* tag 'drm-intel-next-fixes-2018-03-27' of git://anongit.freedesktop.org/drm/drm-intel:
drm/i915: Fix hibernation with ACPI S0 target state
drm/i915/execlists: Use a locked clear_bit() for synchronisation with interrupt
drm/i915: Specify which engines to reset following semaphore/event lockups
drm/i915/dp: Write to SET_POWER dpcd to enable MST hub.
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJauCZfAAoJEHm+PkMAQRiGWGUH/2rhdQDkoJpYWnjaQkolECG8
MxpGE7nmIIHxQcbSDdHTGJ8IhVm6Z5wZ7ym/PwCDTT043Y1y341sJrIwL2/nTG6d
HVidk8hFvgN6QzlzVAHT3ZZMII/V9Zt+VV5SUYLGnPAVuJNHo/6uzWlTU5g+NTFo
IquFDdQUaGBlkKqby+NoAFnkV1UAIkW0g22cfvPnlO5GMer0gusGyVNvVp7TNj3C
sqj4Hvt3RMDLMNe9RZ2pFTiOD096n8FWpYftZneUTxFImhRV3Jg5MaaYZm9SI3HW
tXrv/LChT/F1mi5Pkx6tkT5Hr8WvcrwDMJ4It1kom10RqWAgjxIR3CMm448ileY=
=YKUG
-----END PGP SIGNATURE-----
Backmerge tag 'v4.16-rc7' into drm-next
Linux 4.16-rc7
This was requested by Daniel, and things were getting
a bit hard to reconcile, most of the conflicts were
trivial though.
Kevin Rogovin