With ppc64 we use the deposited pgtable_t to store the hash pte slot
information. We should not withdraw the deposited pgtable_t without
marking the pmd none. This ensure that low level hash fault handling
will skip this huge pte and we will handle them at upper levels.
Recent change to pmd splitting changed the above in order to handle the
race between pmd split and exit_mmap. The race is explained below.
Consider following race:
CPU0 CPU1
shrink_page_list()
add_to_swap()
split_huge_page_to_list()
__split_huge_pmd_locked()
pmdp_huge_clear_flush_notify()
// pmd_none() == true
exit_mmap()
unmap_vmas()
zap_pmd_range()
// no action on pmd since pmd_none() == true
pmd_populate()
As result the THP will not be freed. The leak is detected by check_mm():
BUG: Bad rss-counter state mm:ffff880058d2e580 idx:1 val:512
The above required us to not mark pmd none during a pmd split.
The fix for ppc is to clear the huge pte of _PAGE_USER, so that low
level fault handling code skip this pte. At higher level we do take ptl
lock. That should serialze us against the pmd split. Once the lock is
acquired we do check the pmd again using pmd_same. That should always
return false for us and hence we should retry the access. We do the
pmd_same check in all case after taking plt with
THP (do_huge_pmd_wp_page, do_huge_pmd_numa_page and
huge_pmd_set_accessed)
Also make sure we wait for irq disable section in other cpus to finish
before flipping a huge pte entry with a regular pmd entry. Code paths
like find_linux_pte_or_hugepte depend on irq disable to get
a stable pte_t pointer. A parallel thp split need to make sure we
don't convert a pmd pte to a regular pmd entry without waiting for the
irq disable section to finish.
Fixes: eef1b3ba05 ("thp: implement split_huge_pmd()")
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When PCI bus is unplugged during full hotplug for EEH recovery,
the platform PE instance (struct pnv_ioda_pe) isn't released and
it dereferences the stale PCI bus that has been released. It leads
to kernel crash when referring to the stale PCI bus.
This fixes the issue by correcting the PE's primary bus when it's
oneline at plugging time, in pnv_pci_dma_bus_setup() which is to
be called by pcibios_fixup_bus().
Cc: stable@vger.kernel.org # v4.1+
Reported-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Reported-by: Pradipta Ghosh <pradghos@in.ibm.com>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Tested-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When PE is created, its primary bus is cached to pe->bus. At later
point, the cached primary bus is returned from eeh_pe_bus_get().
However, we could get stale cached primary bus and run into kernel
crash in one case: full hotplug as part of fenced PHB error recovery
releases all PCI busses under the PHB at unplugging time and recreate
them at plugging time. pe->bus is still dereferencing the PCI bus
that was released.
This adds another PE flag (EEH_PE_PRI_BUS) to represent the validity
of pe->bus. pe->bus is updated when its first child EEH device is
online and the flag is set. Before unplugging in full hotplug for
error recovery, the flag is cleared.
Fixes: 8cdb2833 ("powerpc/eeh: Trace PCI bus from PE")
Cc: stable@vger.kernel.org #v3.11+
Reported-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Reported-by: Pradipta Ghosh <pradghos@in.ibm.com>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Tested-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
If a cpu is hotplugged while the hcall trace points are active, it's
possible to hit a warning from RCU due to the trace points calling into
RCU from an offline cpu, eg:
RCU used illegally from offline CPU!
rcu_scheduler_active = 1, debug_locks = 1
Make the hypervisor tracepoints conditional by using
TRACE_EVENT_FN_COND.
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Denis Kirjanov <kda@linux-powerpc.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The GPCI hcall allows for a 4K buffer but we limit the buffer to 1K.
The problem with a 1K buffer is if a request results in returning
more values than can be accomodated in the 1K buffer the request will
fail.
The buffer we are using is currently allocated on the stack and hence
limited in size. Instead use a per-CPU 4K buffer like we do with 24x7
counters (hv-24x7.c).
While here, rename the macro GPCI_MAX_DATA_BYTES to HGPCI_MAX_DATA_BYTES
for consistency with 24x7 counters.
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When M64 BAR is set to Single PE mode, the PE# assigned to VF could be
sparse.
This patch restructures the code to allocate sparse PE# for VFs when M64
BAR is set to Single PE mode. Also it rename the offset to pe_num_map to
reflect the content is the PE number.
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Acked-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Each VF could have 6 BARs at most. When the total BAR size exceeds the
gate, after expanding it will also exhaust the M64 Window.
This patch limits the boundary by checking the total VF BAR size instead of
the individual BAR.
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Acked-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
At the moment 64bit-prefetchable window can be maximum 64GB, which is
currently got from device tree. This means that in shared mode the maximum
supported VF BAR size is 64GB/256=256MB. While this size could exhaust the
whole 64bit-prefetchable window. This is a design decision to set a
boundary to 64MB of the VF BAR size. Since VF BAR size with 64MB would
occupy a quarter of the 64bit-prefetchable window, this is affordable.
This patch replaces magic limit of 64MB with "gate", which is 1/4 of the
M64 Segment Size(m64_segsize >> 2) and adds comment to explain the reason
for it.
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Reviewed-by: Gavin Shan <gwshan@linux.vent.ibm.com>
Acked-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In current implementation, when VF BAR is bigger than 64MB, it uses 4 M64
BARs in Single PE mode to cover the number of VFs required to be enabled.
By doing so, several VFs would be in one VF Group and leads to interference
between VFs in the same group.
And in this patch, m64_wins is renamed to m64_map, which means index number
of the M64 BAR used to map the VF BAR. Based on Gavin's comments. Also
makes sure the VF BAR size is bigger than 32MB when M64 BAR is used in
Single PE mode.
This patch changes the design by using one M64 BAR in Single PE mode for
one VF BAR. This gives absolute isolation for VFs.
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Acked-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The alignment of IOV BAR on PowerNV platform is the total size of the IOV
BAR. No matter whether the IOV BAR is extended with number of
roundup_pow_of_two(total_vfs) or number of max PE number (256), the total
size could be calculated by (vfs_expanded * VF_BAR_size).
This patch simplifies the pnv_pci_iov_resource_alignment() by removing the
first case.
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Acked-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
On PHB3, we enable SRIOV devices by mapping IOV BAR with M64 BARs. If a
SRIOV device's IOV BAR is not 64bit-prefetchable, this is not assigned from
64bit prefetchable window, which means M64 BAR can't work on it.
The reason is PCI bridges support only 2 memory windows and the kernel code
programs bridges in the way that one window is 32bit-nonprefetchable and
the other one is 64bit-prefetchable. So if devices' IOV BAR is 64bit and
non-prefetchable, it will be mapped into 32bit space and therefore M64
cannot be used for it.
This patch makes this explicit and truncate IOV resource in this case to
save MMIO space.
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Acked-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The EEH debugfs handlers have same prototype. This introduces
a macro to define them, then to simplify the code. No logical
changes.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Add 'P' command with optional task_struct address to dump all/one task's
information: task pointer, kernel stack pointer, PID, PPID, state
(interpreted), CPU where (last) running, and command.
Signed-off-by: Douglas Miller <dougmill@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Add the 'do' command to dump the OPAL msglog in xmon.
Signed-off-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
[mpe: Reduce the amount of ifdefery required]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently, the OPAL msglog/console buffer is exposed as a sysfs file, with
the sysfs read handler responsible for retrieving the log from the OPAL
buffer. We'd like to be able to use it in xmon as well.
Refactor the OPAL msglog code to create a new function, opal_msglog_copy(),
that copies to an arbitrary buffer. Separate the initialisation code into
generic memcons init and sysfs file creation.
Signed-off-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The comment block above pcibios_set_pcie_reset_state() incorrectly refers
to pcibios_set_pcie_slot_reset(). Fix the comment accordingly.
Signed-off-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Acked-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
"p5ioc2 is used by approximately 2 machines in the world, and has never
ever been a supported configuration."
The code for p5ioc2 is essentially unused and complicates what is already
a very complicated codebase. Its removal is essentially a "free win" in
the effort to simplify the powernv PCI code.
In addition, support for p5ioc2 has been dropped from skiboot. There's no
reason to keep it around in the kernel.
Signed-off-by: Russell Currey <ruscur@russell.cc>
Acked-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Acked-by: Stewart Smith <stewart@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Since binutils 2.26 BFD is doing suffix merging on STRTAB sections. But
dedotify modifies the symbol names in place, which can also modify
unrelated symbols with a name that matches a suffix of a dotted name. To
remove the leading dot of a symbol name we can just increment the pointer
into the STRTAB section instead.
Backport to all stables to avoid breakage when people update their
binutils - mpe.
Cc: stable@vger.kernel.org
Signed-off-by: Andreas Schwab <schwab@linux-m68k.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The first real batch of fixes for this release cycle, so there are a few more
than usual.
Most of these are fixes and tweaks to board support (DT bugfixes, etc). I've
also picked up a couple of small cleanups that seemed innocent enough that
there was little reason to wait (const/__initconst and Kconfig deps).
Quite a bit of the changes on OMAP were due to fixes to no longer write to
rodata from assembly when ARM_KERNMEM_PERMS was enabled, but there were also
other fixes.
Kirkwood had a bunch of gpio fixes for some boards. OMAP had RTC fixes
on OMAP5, and Nomadik had changes to MMC parameters in DT.
All in all, mostly the usual mix of various fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=1iBu
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"The first real batch of fixes for this release cycle, so there are a
few more than usual.
Most of these are fixes and tweaks to board support (DT bugfixes,
etc). I've also picked up a couple of small cleanups that seemed
innocent enough that there was little reason to wait (const/
__initconst and Kconfig deps).
Quite a bit of the changes on OMAP were due to fixes to no longer
write to rodata from assembly when ARM_KERNMEM_PERMS was enabled, but
there were also other fixes.
Kirkwood had a bunch of gpio fixes for some boards. OMAP had RTC
fixes on OMAP5, and Nomadik had changes to MMC parameters in DT.
All in all, mostly the usual mix of various fixes"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (46 commits)
ARM: multi_v7_defconfig: enable DW_WATCHDOG
ARM: nomadik: fix up SD/MMC DT settings
ARM64: tegra: Add chosen node for tegra132 norrin
ARM: realview: use "depends on" instead of "if" after prompt
ARM: tango: use "depends on" instead of "if" after prompt
ARM: tango: use const and __initconst for smp_operations
ARM: realview: use const and __initconst for smp_operations
bus: uniphier-system-bus: revive tristate prompt
arm64: dts: Add missing DMA Abort interrupt to Juno
bus: vexpress-config: Add missing of_node_put
ARM: dts: am57xx: sbc-am57x: correct Eth PHY settings
ARM: dts: am57xx: cl-som-am57x: fix CPSW EMAC pinmux
ARM: dts: am57xx: sbc-am57x: fix UART3 pinmux
ARM: dts: am57xx: cl-som-am57x: update SPI Flash frequency
ARM: dts: am57xx: cl-som-am57x: set HOST mode for USB2
ARM: dts: am57xx: sbc-am57x: fix SB-SOM EEPROM I2C address
ARM: dts: LogicPD Torpedo: Revert Duplicative Entries
ARM: dts: am437x: pixcir_tangoc: use correct flags for irq types
ARM: dts: am4372: fix irq type for arm twd and global timer
ARM: dts: at91: sama5d4 xplained: fix phy0 IRQ type
...
Commit 16da306849 ("um: kill pfn_t") introduced a compile warning for
defconfig (SUBARCH=i386):
arch/um/kernel/skas/mmu.c:38:206:
warning: right shift count >= width of type [-Wshift-count-overflow]
Aforementioned patch changes the definition of the phys_to_pfn() macro
from
((pfn_t) ((p) >> PAGE_SHIFT))
to
((p) >> PAGE_SHIFT)
This effectively changes the phys_to_pfn() expansion's type from
unsigned long long to unsigned long.
Through the callchain init_stub_pte() => mk_pte(), the expansion of
phys_to_pfn() is (indirectly) fed into the 'phys' argument of the
pte_set_val(pte, phys, prot) macro, eventually leading to
(pte).pte_high = (phys) >> 32;
This results in the warning from above.
Since UML only deals with 32 bit addresses, the upper 32 bits from
'phys' used to be always zero anyway. Also, all page protection flags
defined by UML don't use any bits beyond bit 9. Since the contents of a
PTE are defined within architecture scope only, the ->pte_high member
can be safely removed.
Remove the ->pte_high member from struct pte_t.
Rename ->pte_low to ->pte.
Adapt the pte helper macros in arch/um/include/asm/page.h.
Noteworthy is the pte_copy() macro where a smp_wmb() gets dropped. This
write barrier doesn't seem to be paired with any read barrier though and
thus, was useless anyway.
Fixes: 16da306849 ("um: kill pfn_t")
Signed-off-by: Nicolai Stange <nicstange@gmail.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Nicolai Stange <nicstange@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 944d9fec8d ("hugetlb: add support for gigantic page allocation
at runtime") has added the runtime gigantic page allocation via
alloc_contig_range(), making this support available only when CONFIG_CMA
is enabled. Because it doesn't depend on MIGRATE_CMA pageblocks and the
associated infrastructure, it is possible with few simple adjustments to
require only CONFIG_MEMORY_ISOLATION instead of full CONFIG_CMA.
After this patch, alloc_contig_range() and related functions are
available and used for gigantic pages with just CONFIG_MEMORY_ISOLATION
enabled. Note CONFIG_CMA selects CONFIG_MEMORY_ISOLATION. This allows
supporting runtime gigantic pages without the CMA-specific checks in
page allocator fastpaths.
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Luiz Capitulino <lcapitulino@redhat.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Zhang Yanfei <zhangyanfei@cn.fujitsu.com>
Cc: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: Hillf Danton <hillf.zj@alibaba-inc.com>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
One of the randconfig build failed with the error:
arch/m32r/kernel/smp.c: In function 'smp_flush_tlb_mm':
arch/m32r/kernel/smp.c:283:20: error: subscripted value is neither array nor pointer nor vector
mmc = &mm->context[cpu_id];
^
arch/m32r/kernel/smp.c: In function 'smp_flush_tlb_page':
arch/m32r/kernel/smp.c:353:20: error: subscripted value is neither array nor pointer nor vector
mmc = &mm->context[cpu_id];
^
arch/m32r/kernel/smp.c: In function 'smp_invalidate_interrupt':
arch/m32r/kernel/smp.c:479:41: error: subscripted value is neither array nor pointer nor vector
unsigned long *mmc = &flush_mm->context[cpu_id];
It turned out that CONFIG_SMP was defined but CONFIG_MMU was not
defined. But arch/m32r/include/asm/mmu.h only defines mm_context_t as
an array when both CONFIG_SMP and CONFIG_MMU are defined. And
arch/m32r/kernel/smp.c is always using context as an array. So without
MMU SMP can not work.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Add missing PAN toggling in the futex code
- Fix missing #include that briefly caused issues in -next
- Allow changing of vmalloc permissions with set_memory_* (used by bpf)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCgAGBQJWs2KkAAoJELescNyEwWM0kn4H+gIGvX7Dk792AJlLj8u1hIb6
m+Z4hgLcNIFZCWEGEEWOjHAJ1n2+SgRPdJgDmhN4KP+5Oh9+Qkqhj3wDy7RB05Bf
q3B/dZzr/rASRpycOyNL4CoyqScS7YsP9+X+7tNC8dAMr8UeYahvVKYVwzMlXfDh
4hh3gZkhBQ/hIUse02VtE+OR6lbZAwMYahrM2T9YHslNKanQkpezqBVD4Ic0J5ic
Jkpep8tBdTBLrFm4WERoO6vv8YCrXDP+6DutAO/nOmvHTr07LgkRwiOn+HmoCxiv
Ir5j01SV2SNlr7AfLBWBLN/NluoRByzmQ6SeEsQ3thN35fIsVndStKcAQAAu1nU=
=pr2h
-----END PGP SIGNATURE-----
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"Nothing particularly interesting here, but all important fixes
nonetheless:
- Add missing PAN toggling in the futex code
- Fix missing #include that briefly caused issues in -next
- Allow changing of vmalloc permissions with set_memory_* (used by
bpf)"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: asm: Explicitly include linux/personality.h in asm/page.h
arm64: futex.h: Add missing PAN toggling
arm64: allow vmalloc regions to be set with set_memory_*
The watchdog timer on the SoCFPGA platform is the Synopsys Designware watchdog.
Enable CONFIG_DW_WATCHDOG for the driver to get built.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
The DTSI file for the Nomadik does not properly specify how the
PL180 levelshifter is connected: the Nomadik actually needs all
the five st,sig-dir-* flags set to properly control all lines out.
Further this board supports full power cycling of the card, and
since this variant has no hardware clock gating, it needs a
ridiculously low frequency setting to keep up with the ever
overflowing FIFO.
The pin configuration set-up is a bit of a mystery, because of
course these pins are a mix of inputs and outputs. However the
reference implementation sets all pins to "output" with
unspecified initial value, so let's do that here as well.
Cc: stable@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
asm/page.h uses READ_IMPLIES_EXEC from linux/personality.h but does not
explicitly include it causing build failures in -next where whatever was
causing it to be implicitly included has changed to remove that
inclusion. Add an explicit inclusion to fix this.
Signed-off-by: Mark Brown <broonie@kernel.org>
[will: moved #include inside #ifndef __ASSEMBLY__ block]
Signed-off-by: Will Deacon <will.deacon@arm.com>
futex.h's futex_atomic_cmpxchg_inatomic() does not use the
__futex_atomic_op() macro and needs its own PAN toggling. This was missed
when the feature was implemented.
Fixes: 338d4f49d6 ("arm64: kernel: Add support for Privileged Access Never")
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The range of set_memory_* is currently restricted to the module address
range because of difficulties in breaking down larger block sizes.
vmalloc maps PAGE_SIZE pages so it is safe to use as well. Update the
function ranges and add a comment explaining why the range is restricted
the way it is.
Suggested-by: Laura Abbott <labbott@fedoraproject.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Pull networking fixes from David Miller:
"This looks like a lot but it's a mixture of regression fixes as well
as fixes for longer standing issues.
1) Fix on-channel cancellation in mac80211, from Johannes Berg.
2) Handle CHECKSUM_COMPLETE properly in xt_TCPMSS netfilter xtables
module, from Eric Dumazet.
3) Avoid infinite loop in UDP SO_REUSEPORT logic, also from Eric
Dumazet.
4) Avoid a NULL deref if we try to set SO_REUSEPORT after a socket is
bound, from Craig Gallek.
5) GRO key comparisons don't take lightweight tunnels into account,
from Jesse Gross.
6) Fix struct pid leak via SCM credentials in AF_UNIX, from Eric
Dumazet.
7) We need to set the rtnl_link_ops of ipv6 SIT tunnels before we
register them, otherwise the NEWLINK netlink message is missing
the proper attributes. From Thadeu Lima de Souza Cascardo.
8) Several Spectrum chip bug fixes for mlxsw switch driver, from Ido
Schimmel
9) Handle fragments properly in ipv4 easly socket demux, from Eric
Dumazet.
10) Don't ignore the ifindex key specifier on ipv6 output route
lookups, from Paolo Abeni"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (128 commits)
tcp: avoid cwnd undo after receiving ECN
irda: fix a potential use-after-free in ircomm_param_request
net: tg3: avoid uninitialized variable warning
net: nb8800: avoid uninitialized variable warning
net: vxge: avoid unused function warnings
net: bgmac: clarify CONFIG_BCMA dependency
net: hp100: remove unnecessary #ifdefs
net: davinci_cpdma: use dma_addr_t for DMA address
ipv6/udp: use sticky pktinfo egress ifindex on connect()
ipv6: enforce flowi6_oif usage in ip6_dst_lookup_tail()
netlink: not trim skb for mmaped socket when dump
vxlan: fix a out of bounds access in __vxlan_find_mac
net: dsa: mv88e6xxx: fix port VLAN maps
fib_trie: Fix shift by 32 in fib_table_lookup
net: moxart: use correct accessors for DMA memory
ipv4: ipconfig: avoid unused ic_proto_used symbol
bnxt_en: Fix crash in bnxt_free_tx_skbs() during tx timeout.
bnxt_en: Exclude rx_drop_pkts hw counter from the stack's rx_dropped counter.
bnxt_en: Ring free response from close path should use completion ring
net_sched: drr: check for NULL pointer in drr_dequeue
...
assembly fixes, the other things are mostly board related:
- A series of omap assembly code fixes to fix issues with rodata with
ARM_KERNMEM_PERMS enabled. We had several places writing to rodata,
which is bad. The fix in most cases is to load the value from data
section using a pointer. Let's also enable ARM_KERNMEM_PERMS so
DEBUG_RODATA gets selected by default. And while testing things,
I also added few more loadable driver modules to the defconfig that
I seem to need quite often.
- Fix a long standing omap5 RTC mystery and enable RTC where we need
to ensure the SoC msecure pin is high so we can write to the RTC
registers.
- Fix irq types for am437x
- A series of minor dts fixes for sbc-am57x and cl-som-am57x
- Fixes for torpedo dts to make WLAN behave and to remove a duplicate
i2c rate entry
This series also includes few minor changes that are not stricly
fixes, but would be good to get in during the early -rc cycle:
- Remove legacy mailbox platform data that is no longer needed
- Add the pdata-quirks needed for the new pwm-omap-dmtimer so
people can use it
- Enable ti,mbox-send-noirq that's needed by wkup_m3 driver
- Enable SPLIT and DWARF4 in omap2plus_defconfig as it makes the
initramfs quite a bit smaller
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=NqvQ
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.5/fixes-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Fixes for omaps with the most intrusive stuff being read-only data
assembly fixes, the other things are mostly board related:
- A series of omap assembly code fixes to fix issues with rodata with
ARM_KERNMEM_PERMS enabled. We had several places writing to rodata,
which is bad. The fix in most cases is to load the value from data
section using a pointer. Let's also enable ARM_KERNMEM_PERMS so
DEBUG_RODATA gets selected by default. And while testing things,
I also added few more loadable driver modules to the defconfig that
I seem to need quite often.
- Fix a long standing omap5 RTC mystery and enable RTC where we need
to ensure the SoC msecure pin is high so we can write to the RTC
registers.
- Fix irq types for am437x
- A series of minor dts fixes for sbc-am57x and cl-som-am57x
- Fixes for torpedo dts to make WLAN behave and to remove a duplicate
i2c rate entry
This series also includes few minor changes that are not stricly
fixes, but would be good to get in during the early -rc cycle:
- Remove legacy mailbox platform data that is no longer needed
- Add the pdata-quirks needed for the new pwm-omap-dmtimer so
people can use it
- Enable ti,mbox-send-noirq that's needed by wkup_m3 driver
- Enable SPLIT and DWARF4 in omap2plus_defconfig as it makes the
initramfs quite a bit smaller
* tag 'omap-for-v4.5/fixes-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (23 commits)
ARM: dts: am57xx: sbc-am57x: correct Eth PHY settings
ARM: dts: am57xx: cl-som-am57x: fix CPSW EMAC pinmux
ARM: dts: am57xx: sbc-am57x: fix UART3 pinmux
ARM: dts: am57xx: cl-som-am57x: update SPI Flash frequency
ARM: dts: am57xx: cl-som-am57x: set HOST mode for USB2
ARM: dts: am57xx: sbc-am57x: fix SB-SOM EEPROM I2C address
ARM: dts: LogicPD Torpedo: Revert Duplicative Entries
ARM: dts: am437x: pixcir_tangoc: use correct flags for irq types
ARM: dts: am4372: fix irq type for arm twd and global timer
ARM: dts: Fix wl12xx missing clocks that cause hangs
ARM: OMAP: Add PWM dmtimer platform data quirks
ARM: omap2plus_defconfig: Enable ARM_KERNMEM_PERMS and few loadable modules
ARM: OMAP2+: Fix ppa_zero_params and ppa_por_params for rodata
ARM: OMAP2+: Fix l2_inv_api_params for rodata
ARM: OMAP2+: Fix save_secure_ram_context for rodata
ARM: OMAP2+: Fix l2dis_3630 for rodata
ARM: OMAP2+: Fix wait_dll_lock_timed for rodata
ARM: OMAP2+: Remove legacy mailbox device instantiation
ARM: dts: AM4372: Add ti,mbox-send-noirq to wkup_m3 mailbox
ARM: dts: AM33xx: Add ti,mbox-send-noirq to wkup_m3 mailbox
...
Signed-off-by: Olof Johansson <olof@lixom.net>
- sama5d4: error in DBGU index
- addition of phy properties in several boards
- at91sam9n12ek fix a panel compatible string
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJWqdjFAAoJEAf03oE53VmQG30H/R9luD6d9ebmhaOE7ay40HAy
RrG8wtRQ/zgxf37SntoJxyVxxXWsDsb7sOR1LRXiT7FEGWr3Eip7B1uwmasC8pky
ich2Yj5pGVUH+qscm26GDGyHbNwIrFOQyl1t/R6upVpITlXa0bpaEIXx3RejH8PN
Wk4pMZg/4OkUXlcmYNU0Rz8ban8GfJ428bkLxMKeUXUAjvevNlWqTvOqC+QIrzUC
w3iDoXfhc81sqrOzBzW44H28g7rh//d3TAfzMbM1BJti880QkP+CksG5qHvogI5f
olN4+9QmV9tLXOr2K6iUkM8dwzHYW/3PPBR1CHODjSLP0rQ2Assy+DPxyO64Rtk=
=jJrB
-----END PGP SIGNATURE-----
Merge tag 'at91-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91 into fixes
First fixes for 4.5. Only DT changes:
- sama5d4: error in DBGU index
- addition of phy properties in several boards
- at91sam9n12ek fix a panel compatible string
* tag 'at91-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91:
ARM: dts: at91: sama5d4 xplained: fix phy0 IRQ type
ARM: dts: at91: sama5d4 xplained: properly mux phy interrupt
ARM: dts: at91: sama5d4ek: add phy address and IRQ for macb0
ARM: dts: at91: sama5d2 xplained: add phy address and IRQ for macb0
ARM: dts: at91: at91sam9n12ek: fix panel compatible string
ARM: dts: at91: sama5d4: fix instance id of DBGU
Signed-off-by: Olof Johansson <olof@lixom.net>
The NVIDIA bootloader, nvtboot, expects the "chosen" node to be present
in the device-tree blob and if it is not then it fails to boot the kernel.
Add the chosen node so we can boot the kernel on Tegra132 Norrin with the
nvtboot bootloader.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
This platform recently moved to multi-platform, so missed the global
fixup by commit e324654294 ("ARM: use "depends on" for SoC configs
instead of "if" after prompt"). Fix it now.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
This platform was recently added, so missed the global fixup by
commit e324654294 ("ARM: use "depends on" for SoC configs instead
of "if" after prompt"). Fix it now.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
This newly added code missed the global fixup by commit 75305275a7
("ARM: use const and __initconst for smp_operations"). So fix it now.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
This newly added code missed the global fixup by commit 75305275a7
("ARM: use const and __initconst for smp_operations"). So fix it now.
Also, add missing "static" qualifier.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
The DMA-330 has an "irq_abort" interrupt line on which it signals faults
separately from the "irq[n:0]" channel interrupts. On Juno, this is
wired up to SPI 92; add it to the DT so that DMAC faults are correctly
reported for the driver to reset the thing, rather than leaving it
locked up and waiting to time out.
CC: Liviu Dudau <liviu.dudau@arm.com>
CC: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Pull MIPS fix from Ralf Baechle:
"Just a single revert for a patch which I had upstreamed out of
sequence"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
Revert "MIPS: bcm63xx: nvram: Remove unused bcm63xx_nvram_get_psi_size() function"
Pull x86 fixes from Thomas Gleixner:
"A bit on the largish side due to a series of fixes for a regression in
the x86 vector management which was introduced in 4.3. This work was
started in December already, but it took some time to fix all corner
cases and a couple of older bugs in that area which were detected
while at it
Aside of that a few platform updates for intel-mid, quark and UV and
two fixes for in the mm code:
- Use proper types for pgprot values to avoid truncation
- Prevent a size truncation in the pageattr code when setting page
attributes for large mappings"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (21 commits)
x86/mm/pat: Avoid truncation when converting cpa->numpages to address
x86/mm: Fix types used in pgprot cacheability flags translations
x86/platform/quark: Print boundaries correctly
x86/platform/UV: Remove EFI memmap quirk for UV2+
x86/platform/intel-mid: Join string and fix SoC name
x86/platform/intel-mid: Enable 64-bit build
x86/irq: Plug vector cleanup race
x86/irq: Call irq_force_move_complete with irq descriptor
x86/irq: Remove outgoing CPU from vector cleanup mask
x86/irq: Remove the cpumask allocation from send_cleanup_vector()
x86/irq: Clear move_in_progress before sending cleanup IPI
x86/irq: Remove offline cpus from vector cleanup
x86/irq: Get rid of code duplication
x86/irq: Copy vectormask instead of an AND operation
x86/irq: Check vector allocation early
x86/irq: Reorganize the search in assign_irq_vector
x86/irq: Reorganize the return path in assign_irq_vector
x86/irq: Do not use apic_chip_data.old_domain as temporary buffer
x86/irq: Validate that irq descriptor is still active
x86/irq: Fix a race in x86_vector_free_irqs()
...
Pull perf fixes from Thomas Gleixner:
"This is much bigger than typical fixes, but Peter found a category of
races that spurred more fixes and more debugging enhancements. Work
started before the merge window, but got finished only now.
Aside of that this contains the usual small fixes to perf and tools.
Nothing particular exciting"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (43 commits)
perf: Remove/simplify lockdep annotation
perf: Synchronously clean up child events
perf: Untangle 'owner' confusion
perf: Add flags argument to perf_remove_from_context()
perf: Clean up sync_child_event()
perf: Robustify event->owner usage and SMP ordering
perf: Fix STATE_EXIT usage
perf: Update locking order
perf: Remove __free_event()
perf/bpf: Convert perf_event_array to use struct file
perf: Fix NULL deref
perf/x86: De-obfuscate code
perf/x86: Fix uninitialized value usage
perf: Fix race in perf_event_exit_task_context()
perf: Fix orphan hole
perf stat: Do not clean event's private stats
perf hists: Fix HISTC_MEM_DCACHELINE width setting
perf annotate browser: Fix behaviour of Shift-Tab with nothing focussed
perf tests: Remove wrong semicolon in while loop in CQM test
perf: Synchronously free aux pages in case of allocation failure
...
In file included from mm/vmscan.c:54:0:
include/linux/swapops.h: In function ‘pte_to_swp_entry’:
include/linux/swapops.h:69:2: error: implicit declaration of function ‘pte_swp_soft_dirty’ [-Werror=implicit-function-declaration]
if (pte_swp_soft_dirty(pte))
^
include/linux/swapops.h:70:3: error: implicit declaration of function ‘pte_swp_clear_soft_dirty’ [-Werror=implicit-function-declaration]
pte = pte_swp_clear_soft_dirty(pte);
We support soft dirty tracking only with book3s 64 for now.
So change the Kconfig dependency accordingly. Also CHECKPOINT_RESTORE
feature is not really dependent on SOFT_DIRTY. We track the dependency
between MEM_SOFT_DIRTY and ARCH_SOFT_DIRTY through headers
Fixes: 7207f43665 ("powerpc/mm: Add page soft dirty tracking")
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Pull ARM fixes from Russell King:
"Just one fix for a -fstack-protector-strong problem from Kees Cook,
and adding the new copy_file_range syscall"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: wire up copy_file_range() syscall
ARM: 8500/1: fix atags_to_fdt with stack-protector-strong
- Wire up copy_file_range() syscall from Chandan Rajendra
- Simplify module TOC handling from Alan Modra
- Remove newly added extra definition of pmd_dirty from Stephen Rothwell
- Allow user space to map rtas_rmo_buf from Vasant Hegde
- Fix PE location code from Gavin Shan
- Remove PPMU_HAS_SSLOT flag for Power8 from Madhavan Srinivasan
- Fixup _HPAGE_CHG_MASK from Aneesh Kumar K.V
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=KZ85
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.5-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
- Wire up copy_file_range() syscall from Chandan Rajendra
- Simplify module TOC handling from Alan Modra
- Remove newly added extra definition of pmd_dirty from Stephen Rothwell
- Allow user space to map rtas_rmo_buf from Vasant Hegde
- Fix PE location code from Gavin Shan
- Remove PPMU_HAS_SSLOT flag for Power8 from Madhavan Srinivasan
- Fixup _HPAGE_CHG_MASK from Aneesh Kumar K.V
* tag 'powerpc-4.5-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/mm: Fixup _HPAGE_CHG_MASK
powerpc/perf: Remove PPMU_HAS_SSLOT flag for Power8
powerpc/eeh: Fix PE location code
powerpc/mm: Allow user space to map rtas_rmo_buf
powerpc: Remove newly added extra definition of pmd_dirty
powerpc: Simplify module TOC handling
powerpc: Wire up copy_file_range() syscall
Pull s390 updates from Martin Schwidefsky:
"An optimization for irq-restore, the SSM instruction is quite a bit
slower than an if-statement and a STOSM.
The copy_file_range system all is added.
Cleanup for PCI and CIO.
And a couple of bug fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/cio: update measurement characteristics
s390/cio: ensure consistent measurement state
s390/cio: fix measurement characteristics memleak
s390/zcrypt: Fix cryptographic device id in kernel messages
s390/pci: remove iomap sanity checks
s390/pci: set error state for unusable functions
s390/pci: fix bar check
s390/pci: resize iomap
s390/pci: improve ZPCI_* macros
s390/pci: provide ZPCI_ADDR macro
s390/pci: adjust IOMAP_MAX_ENTRIES
s390/numa: move numa_init_late() from device to arch_initcall
s390: remove all usages of PSW_ADDR_INSN
s390: remove all usages of PSW_ADDR_AMODE
s390: wire up copy_file_range syscall
s390: remove superfluous memblock_alloc() return value checks
s390/numa: allocate memory with correct alignment
s390/irqflags: optimize irq restore
s390/mm: use TASK_MAX_SIZE where applicable
There are a couple of nasty truncation bugs lurking in the pageattr
code that can be triggered when mapping EFI regions, e.g. when we pass
a cpa->pgd pointer. Because cpa->numpages is a 32-bit value, shifting
left by PAGE_SHIFT will truncate the resultant address to 32-bits.
Viorel-Cătălin managed to trigger this bug on his Dell machine that
provides a ~5GB EFI region which requires 1236992 pages to be mapped.
When calling populate_pud() the end of the region gets calculated
incorrectly in the following buggy expression,
end = start + (cpa->numpages << PAGE_SHIFT);
And only 188416 pages are mapped. Next, populate_pud() gets invoked
for a second time because of the loop in __change_page_attr_set_clr(),
only this time no pages get mapped because shifting the remaining
number of pages (1048576) by PAGE_SHIFT is zero. At which point the
loop in __change_page_attr_set_clr() spins forever because we fail to
map progress.
Hitting this bug depends very much on the virtual address we pick to
map the large region at and how many pages we map on the initial run
through the loop. This explains why this issue was only recently hit
with the introduction of commit
a5caa209ba ("x86/efi: Fix boot crash by mapping EFI memmap
entries bottom-up at runtime, instead of top-down")
It's interesting to note that safe uses of cpa->numpages do exist in
the pageattr code. If instead of shifting ->numpages we multiply by
PAGE_SIZE, no truncation occurs because PAGE_SIZE is a UL value, and
so the result is unsigned long.
To avoid surprises when users try to convert very large cpa->numpages
values to addresses, change the data type from 'int' to 'unsigned
long', thereby making it suitable for shifting by PAGE_SHIFT without
any type casting.
The alternative would be to make liberal use of casting, but that is
far more likely to cause problems in the future when someone adds more
code and fails to cast properly; this bug was difficult enough to
track down in the first place.
Reported-and-tested-by: Viorel-Cătălin Răpițeanu <rapiteanu.catalin@gmail.com>
Acked-by: Borislav Petkov <bp@alien8.de>
Cc: Sai Praneeth Prakhya <sai.praneeth.prakhya@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=110131
Link: http://lkml.kernel.org/r/1454067370-10374-1-git-send-email-matt@codeblueprint.co.uk
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
When calling intel_alt_er() with .idx != EXTRA_REG_RSP_* we will not
initialize alt_idx and then use this uninitialized value to index an
array.
When that is not fatal, it can result in an infinite loop in its
caller __intel_shared_reg_get_constraints(), with IRQs disabled.
Alternative error modes are random memory corruption due to the
cpuc->shared_regs->regs[] array overrun, which manifest in either
get_constraints or put_constraints doing weird stuff.
Only took 6 hours of painful debugging to find this. Neither GCC nor
Smatch warnings flagged this bug.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Kan Liang <kan.liang@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Fixes: ae3f011fc2 ("perf/x86/intel: Fix SLM MSR_OFFCORE_RSP1 valid_mask")
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This was wrongly updated by commit 7aa9a23c69 ("powerpc, thp: remove
infrastructure for handling splitting PMDs") during the last merge
window. Fix it up.
This could lead to incorrect behaviour in THP and/or mprotect(), at a
minimum.
Fixes: 7aa9a23c69 ("powerpc, thp: remove infrastructure for handling splitting PMDs")
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Commit 7a7868326d ("powerpc/perf: Add an explict flag indicating
presence of SLOT field") introduced the PPMU_HAS_SSLOT flag to remove
the assumption that MMCRA[SLOT] was present when PPMU_ALT_SIPR was not
set.
That commit's changelog also mentions that Power8 does not support
MMCRA[SLOT]. However when the Power8 PMU support was merged, it
errnoeously included the PPMU_HAS_SSLOT flag.
So remove PPMU_HAS_SSLOT from the Power8 flags.
mpe: On systems where MMCRA[SLOT] exists, the field occupies bits 37:39
(IBM numbering). On Power8 bit 37 is reserved, and 38:39 overlap with
the high bits of the Threshold Event Counter Mantissa. I am not aware of
any published events which use the threshold counting mechanism, which
would cause the mantissa bits to be set. So in practice this bug is
unlikely to trigger.
Fixes: e05b9b9e5c ("powerpc/perf: Power8 PMU support")
Signed-off-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This fixes existing tests broken by barrier rework,
and adds some new tests.
Plus, there's a fix for an old bug in virtio-pci.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWp1yPAAoJECgfDbjSjVRpoEoH/0wHh1vFd1qcuWl78DHHX0fQ
bPY0F2u8Z50xJmn5IRpKeaWTTo1Fet5tWbu6YAymx/6A5BCRao6BxOGAV3cmfDIg
Y9ipb7WGyCYiqZvxydWnK4/ss9/qKuwrRAukBewS7Ggu41WzM2Ui/Ksmq3dqpgsp
ZyJaXOCgESNpQ01ScKrANQlQ01T6+jAZu2fY7sO67YXQXjI91oQqI2Ox52GOPXQK
fFEAyPb9kYsEcBRwN6hl/w/yb34j+735tA/f0VA7DrEpXmyez4hG3bGTIbG4KcW3
QpjuBScL0Ik3wLjZgixOPQza44FhQBi8QNIjW0mSoracRyQ9ZZPhYYtBkKX33xk=
=aJRN
-----END PGP SIGNATURE-----
Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
Pull virtio tests and fixes from Michael Tsirkin:
"This fixes existing tests broken by barrier rework, and adds some new
tests.
Plus, there's a fix for an old bug in virtio-pci"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
tools/virtio: add ringtest utilities
sh: fix smp_store_mb for !SMP
tools/virtio: use virt_xxx barriers
virtio_pci: fix use after free on release
This reverts commit 5bdb102b3f.
Brian Norris <computersforpeace@gmail.com> is reporting:
Ralf,
Please revert this and send it to Linus (or else, I can send it myself).
This is causing build failures, because I didn't take the rest of
Simon's series yet.
drivers/mtd/bcm63xxpart.c: In function 'bcm63xx_parse_cfe_partitions':
drivers/mtd/bcm63xxpart.c:93:2: error: implicit declaration of function
'bcm63xx_nvram_get_psi_size' [-Werror=implicit-function-declaration]
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
References: https://www.linux-mips.org/cgi-bin/mesg.cgi?a=linux-mips&i=20160126191607.GA111152%40google.com
- Ensure we don't access PMU registers of the PMU is not implemented
(fixes booting under QEMU)
- Fix BUG_ON triggered during module loading with DEBUG_SET_MODULE_RONX
- Ensure the kasan zero page is read-only
- Hide __efistub_ symbol aliases from kallsyms, since they otherwise
confuse the backtrace code
- Ensure !PTE_WRITE kernel ptes are marked as read-only
- defconfig updates based on requests and patches on the list
- Other minor fixes (typos, build system)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCgAGBQJWp7gyAAoJELescNyEwWM0At0H/2o0GeFS2mEQILShWv7SHaPG
Fvon25UTHPwfS5zhejtBYpuISJZTFql4KBKtoT6dHxf4U+gb+zicSZJHlkoxJfRV
8JBD5DmS2OcO9+JtgAey5O1w0yZ9prVr45QQrLmDGZBDKV9AivT31I/BNnnq3LWJ
dg9pbHrvLanR54qpYjWoW0S0Sop93XCHc8y2Q66hDFrG3zkXkQfy6VCsJq/LdnAp
wlCY/5QbbKufm+LP0jpmefq6brCGh0v7bCpOO3nwSPtD1iMrT6odAKjiBmPeE59r
XvOd5g760tZnVLSeLR0Iqq9PLdsdBvd5gHQlMfyBAIt7xhfEEH7b8Tthh1bSRPU=
=ldNV
-----END PGP SIGNATURE-----
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"The main thing here is to get us booting under qemu again after it
turned out that not all of the PMU registers are emulated there,
causing us to die early in boot.
- Ensure we don't access PMU registers of the PMU is not implemented
(fixes booting under QEMU)
- Fix BUG_ON triggered during module loading with DEBUG_SET_MODULE_RONX
- Ensure the kasan zero page is read-only
- Hide __efistub_ symbol aliases from kallsyms, since they otherwise
confuse the backtrace code
- Ensure !PTE_WRITE kernel ptes are marked as read-only
- defconfig updates based on requests and patches on the list
- Other minor fixes (typos, build system)"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: mm: avoid calling apply_to_page_range on empty range
arm64: defconfig: updates for 4.5
arm64: errata: Add -mpc-relative-literal-loads to build flags
Eliminate the .eh_frame sections from the aarch64 vmlinux and kernel modules
arm64: Fix an enum typo in mm/dump.c
arm64: Honour !PTE_WRITE in set_pte_at() for kernel mappings
arm64: kernel: fix architected PMU registers unconditional access
arm64: kasan: ensure that the KASAN zero page is mapped read-only
arm64: hide __efistub_ aliases from kallsyms
Update Eth PHY settings to make it possible to run both phys at 1Gbps.
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
On-board SPI flash cat act at 48Mhz SPI bus frequency.
Update the DT frequency property.
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Revert commit 7cd6ca770d ("ARM: dts: Change I2C2 and I2C3 to 400KHz
for LogicPD Torpedo DM3730 devkit") It was already done and it is
just a duplicate.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Now IRQs for Pixcir Tangoc touchscreen are defined using
IRQ_TYPE_NONE in am437x-gp-evm.dts and am43x-epos-evm.dts wich
do not correspond HW.
Hence, update am437x-gp-evm.dts and am43x-epos-evm.dts files
and use correct flag IRQ_TYPE_EDGE_FALLING for irq types.
While here, remove duplicated irq declaration for pixcir_ts@5c node
in am437x-gp-evm.dts.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
As per ARM documentation
PPI(0) ID27 - global timer interrupt is rising-edge sensitive.
PPI(2) ID29 - twd interrupt is rising-edge sensitive.
and the same is proved by GIC distributor register value
GIC_DIST_CONFIG(0xC04) = 0x7DC00000.
Hence, set IRQ triggering type to IRQ_TYPE_EDGE_RISING
for ARM TWD and Global timers.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
For phy0 KSZ8081, the type of GPIO IRQ should be "level low" instead of
"edge falling".
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Fixes: 38153a0178 ("ARM: at91/dt: sama5d4: add dts for sama5d4 xplained board")
Cc: <stable@vger.kernel.org> # 4.1+
No interrupt were received from the phy because PIOE 1 may not be properly
muxed. It prevented proper link detection, especially since commit
321beec504 ("net: phy: Use interrupts when available in NOLINK state")
disables polling.
Cc: <stable@vger.kernel.org> # 4.4
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
On SAMA5D4EK board, the Ethernet doesn't work after resuming from the suspend
state.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
[nicolas.ferre@atmel.com: adapt to newer kernel]
Fixes: 38153a0178 ("ARM: at91/dt: sama5d4: add dts for sama5d4 xplained board")
Cc: <stable@vger.kernel.org> # 4.1+
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
After 57a38effa5 (net: phy: micrel: disable broadcast for KSZ8081/KSZ8091)
the macb0 interface has difficulties to come back from power saving mode if
address not explicitly set up.
As the micrel phy on the board is actually configured to show up at address 1
we use this explicitly.
Adding the phy node and its real address fixes the issue.
The phy IRQ and associated pinmux node is also added.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: stable@vger.kernel.org # 4.4+ // manual merge needed
Properly use qiaodian as the vendor prefix for the panel.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
In eeh_pe_loc_get(), the PE location code is retrieved from the
"ibm,loc-code" property of the device node for the bridge of the
PE's primary bus. It's not correct because the property indicates
the parent PE's location code.
This reads the correct PE location code from "ibm,io-base-loc-code"
or "ibm,slot-location-code" property of PE parent bus's device node.
Cc: stable@vger.kernel.org # v3.16+
Fixes: 357b2f3dd9 ("powerpc/eeh: Dump PE location code")
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Tested-by: Russell Currey <ruscur@russell.cc>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Building with CONFIG_CC_STACKPROTECTOR_STRONG triggers protection code
generation under CONFIG_ARM_ATAG_DTB_COMPAT but this is too early for
being able to use any of the stack_chk code. Explicitly disable it for
only the atags_to_fdt bits.
Suggested-by: zhxihu <zhxihu@marvell.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
For PAE kernels "unsigned long" is not suitable to hold page protection
flags, since _PAGE_NX doesn't fit there. This is the reason for quite a
few W+X pages getting reported as insecure during boot (observed namely
for the entire initrd range).
Fixes: 281d4078be ("x86: Make page cache mode a real type")
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Reviewed-by: Juergen Gross <JGross@suse.com>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/56A7635602000078000CAFF1@prv-mh.provo.novell.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Calling apply_to_page_range with an empty range results in a BUG_ON
from the core code. This can be triggered by trying to load the st_drv
module with CONFIG_DEBUG_SET_MODULE_RONX enabled:
kernel BUG at mm/memory.c:1874!
Internal error: Oops - BUG: 0 [#1] PREEMPT SMP
Modules linked in:
CPU: 3 PID: 1764 Comm: insmod Not tainted 4.5.0-rc1+ #2
Hardware name: ARM Juno development board (r0) (DT)
task: ffffffc9763b8000 ti: ffffffc975af8000 task.ti: ffffffc975af8000
PC is at apply_to_page_range+0x2cc/0x2d0
LR is at change_memory_common+0x80/0x108
This patch fixes the issue by making change_memory_common (called by the
set_memory_* functions) a NOP when numpages == 0, therefore avoiding the
erroneous call to apply_to_page_range and bringing us into line with x86
and s390.
Cc: <stable@vger.kernel.org>
Reviewed-by: Laura Abbott <labbott@redhat.com>
Acked-by: David Rientjes <rientjes@google.com>
Signed-off-by: Mika Penttilä <mika.penttila@nextfour.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The kernel now always uses vector registers when available, however KVM
has special logic if support is really enabled for a guest. If support
is disabled, guest_fpregs.fregs will only contain memory for the fpu.
The kernel, however, will store vector registers into that area,
resulting in crazy memory overwrites.
Simply extending that area is not enough, because the format of the
registers also changes. We would have to do additional conversions, making
the code even more complex. Therefore let's directly use one place for
the vector/fpu registers + fpc (in kvm_run). We just have to convert the
data properly when accessing it. This makes current code much easier.
Please note that vector/fpu registers are now always stored to
vcpu->run->s.regs.vrs. Although this data is visible to QEMU and
used for migration, we only guarantee valid values to user space when
KVM_SYNC_VRS is set. As that is only the case when we have vector
register support, we are on the safe side.
Fixes: b5510d9b68 ("s390/fpu: always enable the vector facility if it is available")
Cc: stable@vger.kernel.org # v4.4 d9a3a09af5 s390/kvm: remove dependency on struct save_area definition
Signed-off-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
[adopt to d9a3a09af5]
The KVM-VFIO device is used by the QEMU VFIO device. It is used to
record the list of in-use VFIO groups so that KVM can manipulate
them.
While we don't need this on s390 currently, let's try to be like
everyone else.
Signed-off-by: Dong Jia Shi <bjsdjshi@linux.vnet.ibm.com>
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
fprs is never freed, therefore resulting in a memory leak if
kvm_vcpu_init() fails or the vcpu is destroyed.
Fixes: 9977e886cb ("s390/kernel: lazy restore fpu registers")
Cc: stable@vger.kernel.org # v4.3+
Reported-by: Eric Farman <farman@linux.vnet.ibm.com>
Signed-off-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Reviewed-by: Eric Farman <farman@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Since each iomap_entry handles only one bar of one pci function
(even when disjunct ranges of a bar are mapped) the sanity check
in pci_iomap_range is not needed and can be removed.
Also convert the remaining BUG_ONs to WARN_ONs.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Reviewed-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
We receive special notifications from firmware when an error was detected
and a pci function became unusable. Set the error_state accordingly to give
device drivers a hint that they don't need to try error recovery.
Suggested-by: Alexander Schmidt <alexschm@de.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Reviewed-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Fix the check which bar space we should map to allow available bars only.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Reviewed-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
On s390 we need to maintain a mapping between iomem addresses
and arch specific function identifiers. Currently the mapping
table is created as such that we could span the whole iomem
address space. Since we can only map each bar space from each
possible function we have an upper bound for the number of
mapping entries.
This reduces the size of the iomap from 256K to less than 4K
(using the defconfig).
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Reviewed-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Most of the constants defined in pci_io.h depend on each other
and thus can be calculated.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Reviewed-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Provide and use a ZPCI_ADDR macro as the complement of ZPCI_IDX
to get rid of some constants in the code.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Reviewed-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
ZPCI_IOMAP_MAX_ENTRIES is off by one. Let's adjust this
for the sake of correctness.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Reviewed-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Commit 3e89e1c5ea ("hugetlb: make mm and fs code explicitly non-modular")
moves hugetlb_init() from module_init to subsys_initcall.
The hugetlb_init()->hugetlb_register_node() code accesses "node->dev.kobj"
which is initialized in numa_init_late().
Since numa_init_late() is a device_initcall which is called *after*
subsys_initcall the above mentioned patch breaks NUMA on s390.
So fix this and move numa_init_late() to arch_initcall.
Fixes: 3e89e1c5ea ("hugetlb: make mm and fs code explicitly non-modular")
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Based on requests, update our defconfig so that:
- We don't build any modules
- PL031 is enabled (RTC emulated by qemu)
- Xen guest support is enabled
- The Uniphier built-in I2C controller is enabled
- PCI host controller drivers for the various arm64 SoCs are enabled
- Device passthrough works on Seattle using SMMU and VFIO
- The Hisilicon IRQ controller (mbigen) is enabled
Signed-off-by: Will Deacon <will.deacon@arm.com>
GCC6 (and Linaro's 2015.12 snapshot of GCC5) has a new default that uses
adrp/ldr or adrp/add to address literal pools. When CONFIG_ARM64_ERRATUM_843419
is enabled, modules built with this toolchain fail to load:
module libahci: unsupported RELA relocation: 275
This patch fixes the problem by passing '-mpc-relative-literal-loads'
to the compiler.
Cc: stable@vger.kernel.org
Fixes: df057cc7b4 ("arm64: errata: add module build workaround for erratum #843419")
BugLink: http://bugs.launchpad.net/bugs/1533009
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Suggested-by: Christophe Lyon <christophe.lyon@linaro.org>
Signed-off-by: Dann Frazier <dann.frazier@canonical.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
By default the aarch64 gcc generates .eh_frame sections. Unlike
.debug_frame sections, the .eh_frame sections are loaded into memory
when the associated code is loaded. On an example kernel being built
with this default the .eh_frame section in vmlinux used an extra 1.7MB
of memory. The x86 disables the creation of the .eh_frame section.
The aarch64 should probably do the same to save some memory.
Signed-off-by: William Cohen <wcohen@redhat.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
sh variant of smp_store_mb() calls xchg() on !SMP which is stronger than
implied by both the name and the documentation.
commit 90a3ccb0be ("sh: define __smp_xxx,
fix smp_store_mb for !SMP") was supposed to fix it but
left the bug in place.
Drop smp_store_mb, so that code in asm-generic/barrier.h
will define it correctly depending on CONFIG_SMP.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The tcxo-clock-frequency binding is listed as optional,
but without it the wl12xx used on the torpedo + wireless
may hang. Scanning also appears broken without this patch.
Signed-off-by: Adam Ford <aford173@gmail.com>
Fixes: 687c276761 ("ARM: dts: Add minimal support for LogicPD
Torpedo DM3730 devkit")
Cc: stable@vger.kernel.org # v4.2+
Signed-off-by: Tony Lindgren <tony@atomide.com>
In order to set the currently platform dependent dmtimer
functions pointers as platform data for the pwm-omap-dmtimer
platform driver, add it to plat-omap auxdata_lookup table.
Suggested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Here're a few gpio pin related fixes:
- remove pinctrl-0 definition from pinctrl, since those pins are used
in other places such as gpio-fan and regulators.
- keep initial state of power led
- fix for alarm pin of gpio-fan.
Fixes: dc57844a73 ("ARM: dts: orion5x: add buffalo linkstation ls-wtgl")
Signed-off-by: Roger Shimizu <rogershimizu@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
For kirkwood, gpio pins starts from 32 are in the 2nd bank, so it should be
converted to "gpio1 <pin minus 32>" in dts file.
e.g. gpio 40 should be "gpio1 8"
The pin/bank issue was found when discussing Debian Bug #810894
[https://bugs.debian.org/810894#47]
Fixes: c43379e150 ("ARM: dts: add buffalo linkstation ls-wvl/vl")
Reported-by: Arnaud Patard (Rtp) <arnaud.patard@rtp-net.org>
Signed-off-by: Roger Shimizu <rogershimizu@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
For kirkwood, gpio pins starts from 32 are in the 2nd bank, so it should be
converted to "gpio1 <pin minus 32>" in dts file.
e.g. gpio 40 should be "gpio1 8"
Besides, a few other pin fixes for ls-wxl/wsxl, to match with mpp pin
definition:
- gpio-leds: "lswxl:blue:power" pin
- gpio-leds: "lswxl:red:func" pin
- gpio-leds: "lswxl:red:hdderr0" pin
- gpio-leds: "lswxl:red:hdderr1" pin
- gpio-fan: low/high/alarm pin
The pin/bank issue was found when discussing Debian Bug #810894
[https://bugs.debian.org/810894#47]
Fixes: e54e4b1b62 ("ARM: dts: add buffalo linkstation ls-wxl/wsxl")
Reported-by: Arnaud Patard (Rtp) <arnaud.patard@rtp-net.org>
Signed-off-by: Roger Shimizu <rogershimizu@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This aligns the stack pointer in chacha20_4block_xor_ssse3 to 64 bytes.
Fixes general protection faults and potential kernel panics.
Cc: stable@vger.kernel.org
Signed-off-by: Eli Cooper <elicooper@gmx.com>
Acked-by: Martin Willi <martin@strongswan.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
As of commit e488ca9f8d ("doc: dt: mtd: partitions: add compatible
property to "partitions" node"), the "partitions" subnode of an SPI
FLASH device node must have a compatible property. The partitions are no
longer detected if it is not present.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
As of commit e488ca9f8d ("doc: dt: mtd: partitions: add compatible
property to "partitions" node"), the "partitions" subnode of an SPI
FLASH device node must have a compatible property. The partitions are no
longer detected if it is not present.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This patch fixes a typo in mm/dump.c:
"MODUELS_END_NR" should be "MODULES_END_NR".
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Currently, set_pte_at() only checks the software PTE_WRITE bit for user
mappings when it sets or clears the hardware PTE_RDONLY accordingly. The
kernel ptes are written directly without any modification, relying
solely on the protection bits in macros like PAGE_KERNEL. However,
modifying kernel pte attributes via pte_wrprotect() would be ignored by
set_pte_at(). Since pte_wrprotect() does not set PTE_RDONLY (it only
clears PTE_WRITE), the new permission is not taken into account.
This patch changes set_pte_at() to adjust the read-only permission for
kernel ptes as well. As a side effect, existing PROT_* definitions used
for kernel ioremap*() need to include PTE_DIRTY | PTE_WRITE.
(additionally, white space fix for PTE_KERNEL_ROX)
Acked-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Tested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Reported-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The Performance Monitors extension is an optional feature of the
AArch64 architecture, therefore, in order to access Performance
Monitors registers safely, the kernel should detect the architected
PMU unit presence through the ID_AA64DFR0_EL1 register PMUVer field
before accessing them.
This patch implements a guard by reading the ID_AA64DFR0_EL1 register
PMUVer field to detect the architected PMU presence and prevent accessing
PMU system registers if the Performance Monitors extension is not
implemented in the core.
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: <stable@vger.kernel.org>
Fixes: 60792ad349 ("arm64: kernel: enforce pmuserenr_el0 initialization and restore")
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reported-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Will Deacon <will.deacon@arm.com>
When switching from the early KASAN shadow region, which maps the
entire shadow space read-write, to the permanent KASAN shadow region,
which uses a zero page to shadow regions that are not subject to
instrumentation, the lowest level table kasan_zero_pte[] may be
reused unmodified, which means that the mappings of the zero page
that it contains will still be read-write.
So update it explicitly to map the zero page read only when we
activate the permanent mapping.
Acked-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Commit e8f3010f73 ("arm64/efi: isolate EFI stub from the kernel
proper") isolated the EFI stub code from the kernel proper by prefixing
all of its symbols with __efistub_, and selectively allowing access to
core kernel symbols from the stub by emitting __efistub_ aliases for
functions and variables that the stub can access legally.
As an unintended side effect, these aliases are emitted into the
kallsyms symbol table, which means they may turn up in backtraces,
e.g.,
...
PC is at __efistub_memset+0x108/0x200
LR is at fixup_init+0x3c/0x48
...
[<ffffff8008328608>] __efistub_memset+0x108/0x200
[<ffffff8008094dcc>] free_initmem+0x2c/0x40
[<ffffff8008645198>] kernel_init+0x20/0xe0
[<ffffff8008085cd0>] ret_from_fork+0x10/0x40
The backtrace in question has nothing to do with the EFI stub, but
simply returns one of the several aliases of memset() that have been
recorded in the kallsyms table. This is undesirable, since it may
suggest to people who are not aware of this that the issue they are
seeing is somehow EFI related.
So hide the __efistub_ aliases from kallsyms, by emitting them as
absolute linker symbols explicitly. The distinction between those
and section relative symbols is completely irrelevant to these
definitions, and to the final link we are performing when these
definitions are being taken into account (the distinction is only
relevant to symbols defined inside a section definition when performing
a partial link), and so the resulting values are identical to the
original ones. Since absolute symbols are ignored by kallsyms, this
will result in these values to be omitted from its symbol table.
After this patch, the backtrace generated from the same address looks
like this:
...
PC is at __memset+0x108/0x200
LR is at fixup_init+0x3c/0x48
...
[<ffffff8008328608>] __memset+0x108/0x200
[<ffffff8008094dcc>] free_initmem+0x2c/0x40
[<ffffff8008645198>] kernel_init+0x20/0xe0
[<ffffff8008085cd0>] ret_from_fork+0x10/0x40
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
With commit 90a545e9 (restrict /dev/mem to idle io memory ranges) mapping
rtas_rmo_buf from user space is failing. Hence we are not able to make
RTAS syscall.
This patch calls page_is_rtas_user_buf before calling iomem_is_exclusive
in devmem_is_allowed(). This will allow user space to map rtas_rmo_buf
and we are able to make RTAS syscall.
Reported-by: Bharata B Rao <bharata@linux.vnet.ibm.com>
CC: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Vasant Hegde <hegdevasant@linux.vnet.ibm.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Pull MIPS updates from Ralf Baechle:
"This is the main pull request for MIPS for 4.5 plus some 4.4 fixes.
The executive summary:
- ATH79 platform improvments, use DT bindings for the ATH79 USB PHY.
- Avoid useless rebuilds for zboot.
- jz4780: Add NEMC, BCH and NAND device tree nodes
- Initial support for the MicroChip's DT platform. As all the device
drivers are missing this is still of limited use.
- Some Loongson3 cleanups.
- The unavoidable whitespace polishing.
- Reduce clock skew when synchronizing the CPU cycle counters on CPU
startup.
- Add MIPS R6 fixes.
- Lots of cleanups across arch/mips as fallout from KVM.
- Lots of minor fixes and changes for IEEE 754-2008 support to the
FPU emulator / fp-assist software.
- Minor Ralink, BCM47xx and bcm963xx platform support improvments.
- Support SMP on BCM63168"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (84 commits)
MIPS: zboot: Add support for serial debug using the PROM
MIPS: zboot: Avoid useless rebuilds
MIPS: BMIPS: Enable ARCH_WANT_OPTIONAL_GPIOLIB
MIPS: bcm63xx: nvram: Remove unused bcm63xx_nvram_get_psi_size() function
MIPS: bcm963xx: Update bcm_tag field image_sequence
MIPS: bcm963xx: Move extended flash address to bcm_tag header file
MIPS: bcm963xx: Move Broadcom BCM963xx image tag data structure
MIPS: bcm63xx: nvram: Use nvram structure definition from header file
MIPS: bcm963xx: Add Broadcom BCM963xx board nvram data structure
MAINTAINERS: Add KVM for MIPS entry
MIPS: KVM: Add missing newline to kvm_err()
MIPS: Move KVM specific opcodes into asm/inst.h
MIPS: KVM: Use cacheops.h definitions
MIPS: Break down cacheops.h definitions
MIPS: Use EXCCODE_ constants with set_except_vector()
MIPS: Update trap codes
MIPS: Move Cause.ExcCode trap codes to mipsregs.h
MIPS: KVM: Make kvm_mips_{init,exit}() static
MIPS: KVM: Refactor added offsetof()s
MIPS: KVM: Convert EXPORT_SYMBOL to _GPL
...
As most platforms implement the PROM serial interface prom_putchar()
add a simple bridge to allow re-using this code for zboot.
Signed-off-by: Alban Bedel <albeu@free.fr>
Cc: Alex Smith <alex.smith@imgtec.com>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11811/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add dummy.o to the targets list, and fill targets automatically from
$(vmlinuzobjs) to avoid having to maintain two lists.
When building with XZ compression copy ashldi3.c to the build
directory to use a different object file for the kernel and zboot.
Without this the same object file need to be build with different
flags which cause a rebuild at every run.
Signed-off-by: Alban Bedel <albeu@free.fr>
Cc: linux-mips@linux-mips.org
Cc: Alex Smith <alex.smith@imgtec.com>
Cc: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11810/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Remove bcm63xx_nvram_get_psi_size() as it now has no users.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Jonas Gorski <jogo@openwrt.org>
Cc: Linux Kernel Mailing List <linux-kernel@vger.kernel.org>
Cc: MIPS Mailing List <linux-mips@linux-mips.org>
Cc: MTD Maling List <linux-mtd@lists.infradead.org>
Patchwork: https://patchwork.linux-mips.org/patch/11836/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Move Broadcom BCM963xx image tag data structure to include/linux/
so that drivers outside of mach-bcm63xx can use it.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Jonas Gorski <jogo@openwrt.org>
Cc: Linux Kernel Mailing List <linux-kernel@vger.kernel.org>
Cc: MIPS Mailing List <linux-mips@linux-mips.org>
Cc: MTD Maling List <linux-mtd@lists.infradead.org>
Patchwork: https://patchwork.linux-mips.org/patch/11832/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Use the common definition of the nvram structure from the header file
include/linux/bcm963xx_nvram.h instead of maintaining a separate copy.
Read the version 5 size of nvram data from memory and then call the
new checksum verification function from the header file.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Jonas Gorski <jogo@openwrt.org>
Cc: Linux Kernel Mailing List <linux-kernel@vger.kernel.org>
Cc: MIPS Mailing List <linux-mips@linux-mips.org>
Cc: MTD Maling List <linux-mtd@lists.infradead.org>
Patchwork: https://patchwork.linux-mips.org/patch/11831/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The header arch/mips/kvm/opcode.h defines a few extra opcodes which
aren't in arch/mips/include/uapi/asm/inst.h. There's nothing KVM
specific about them, so lets move them into inst.h where they belong and
delete the header.
Note that mfmcz_op is renamed to mfmc0_op to match the instruction set
manual, and wait_op was already added to inst.h in commit b0a3eae2b9
("MIPS: inst.h: define COP0 wait op"), merged in v3.16-rc1.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11895/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Drop the custom cache operation code definitions used by KVM for
emulating guest CACHE instructions, and switch to use the existing
definitions in <asm/cacheops.h>.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: kvm@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11893/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Most of the cache op codes defined in cacheops.h are split into a 2-bit
cache identifier, and a 3-bit cache op code which does largely the same
thing semantically regardless of the cache identifier.
To allow the use of these definitions by KVM for decoding cache ops,
break the definitions down into parts where it makes sense to do so, and
add masks for the Cache and Op field within the cache op.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: kvm@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11892/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The first argument to set_except_vector is the ExcCode, which we now
have definitions for. Lets make use of them.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11894/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add a few missing trap codes.
[ralf@linux-mips.org: Drop removal of exception codes. I don't care what
the incomplete architecture spec says; it can't change existing hardware
and VCEI is supported indeed.]
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: kvm@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11890/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Move the Cause.ExcCode trap code definitions from kvm_host.h to
mipsregs.h, since they describe architectural bits rather than KVM
specific constants, and change the prefix from T_ to EXCCODE_.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11891/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The module init and exit functions have no need to be global, so make
them static.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: kvm@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11889/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When calculating the offsets into the commpage for dynamically
translated mtc0/mfc0 guest instructions, multiple offsetof()s are added
together to find the offset of the specific register in the mips_coproc,
within the commpage.
Simplify each of these cases to a single offsetof() to find the offset
of the specific register within the commpage.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11888/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Export symbols only to GPL modules to match other KVM symbols in
virt/kvm/ and arch/*/kvm/.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11887/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The function kvm_mips_host_tlb_inv_index() is unused, so drop it
completely.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11886/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The CAUSEB_DC and CAUSEF_DC definitions used by KVM are defined in
asm/kvm_host.h, but all the other Cause register field definitions are
found in asm/mipsregs.h.
Lets reunite the DC bit definitions with its friends in mipsregs.h.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11885/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Some definitions in the MIPS asm/kvm_host.h are completely unused, so
lets drop them.
MS_TO_NS is no longer used since commit e30492bbe9 ("MIPS: KVM:
Rewrite count/compare timer emulation"). The others don't appear ever to
have been used.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: kvm@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11884/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This adds basic DTS configuration for the PIC32MZDA chip and in turn the
PIC32MZDA Starter Kit.
Signed-off-by: Joshua Henderson <joshua.henderson@microchip.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12104/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This adds support for the Microchip PIC32 MIPS microcontroller with the
specific variant PIC32MZDA. PIC32MZDA is based on the MIPS m14KEc core
and boots using device tree.
This includes an early pin setup and early clock setup needed prior to
device tree being initialized. In additon, an interface is provided to
synchronize access to registers shared across several peripherals.
Signed-off-by: Joshua Henderson <joshua.henderson@microchip.com>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12097/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The cp0_tcstatus member of struct pt_regs was removed along with the
rest of SMTC in v3.16, commit b633648c5a ("MIPS: MT: Remove SMTC
support"), however recent uprobes support in v4.3 added back a reference
to it in the regoffset_table[] in ptrace.c. Remove it.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Fixes: 40e084a506 ("MIPS: Add uprobes support.")
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11920/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-mips@linux-mips.org
Cc: linux-gpio@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11925/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-mips@linux-mips.org
Cc: linux-gpio@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11924/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-mips@linux-mips.org
Cc: linux-gpio@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11923/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Cc: Alban Bedel <albeu@free.fr>
Cc: linux-mips@linux-mips.org
Cc: linux-gpio@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11922/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-mips@linux-mips.org
Cc: linux-gpio@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11921/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Change the CONFIG_MIPS_CMDLINE_EXTEND to CONFIG_MIPS_CMDLINE_DTB_EXTEND
to resolve the EXTEND_WITH_PROM macro.
Signed-off-by: Jaedon Shin <jaedon.shin@gmail.com>
Fixes: 2024972ef5 ("MIPS: Make the kernel arguments from dtb available")
Reviewed-by: Alexander Sverdlin <alexander.svedlin@gmail.com>
Cc: Jonas Gorski <jogo@openwrt.org>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Aaro Koskinen <aaro.koskinen@nokia.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11909/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The kernel currently assumes that a core will start up in legacy mode
using the exception base provided through the CM GCR registers. If a
core has been configured in hardware to start in EVA mode, these
assumptions will fail.
This patch ensures that secondary cores are initialized to meet these
assumptions.
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Reviewed-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11907/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Fix the description of the microMIPS NOP16 encoding or MM_NOP16, which
is not equivalent to the MIPS16 NOP instruction. This is 0x0c00 and
represents the microMIPS `MOVE16 $0, $0' operation, whereas MIPS16 NOP
is encoded as 0x6500, representing `MOVE $0, $16'.
Also fix a typo in `mm_fp0_format' description.
Signed-off-by: Maciej W. Rozycki <macro@imgtec.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12177/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Remove irrelevant content from the description of the emulation frame in
`mips_dsemul', referring to bare-metal configurations. Update the text,
reflecting the change made with commit ba3049ed40 ("MIPS: Switch FPU
emulator trap to BREAK instruction."), where we switched from using an
address error exception on an unaligned access to the use of a BREAK 514
instruction causing a breakpoint exception instead.
Signed-off-by: Maciej W. Rozycki <macro@imgtec.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12176/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Emulate the microMIPS ADDIUPC instruction directly in `mips_dsemul'. If
executed in the emulation frame, this instruction produces an incorrect
result, because the value of the PC there is not the same as where the
instruction originated.
Reshape code so as to handle all microMIPS cases together.
Signed-off-by: Maciej W. Rozycki <macro@imgtec.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12175/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Aneesh Kumar K.V