Last remaining DMA channel definitions in arch/arm/mach-omap2/dma.h
are used only by omap_hwmod_2xxx_3xxx_ipblock_data.c and
omap_hwmod_3xxx_data.c. Remove them by using directly DMA channel number in
hwmod data and drop definitions with a following script:
egrep '#define [OMAP|AM35XX].*DMA' arch/arm/mach-omap2/dma.h | cut -f 1,3 \
| while read i; do \
DEF=`echo $i |cut -d ' ' -f 2`; \
CH=`echo $i |cut -d ' ' -f 3`; \
echo "removing" $DEF; \
sed -i "s/${DEF}/${CH}/" arch/arm/mach-omap2/omap_hwmod_*.c; \
sed -i "/${DEF}/d" arch/arm/mach-omap2/dma.h; \
done
Signed-off-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The different generations of OMAP2+ SoCs have almost the same
mailbox IP, but the IP has configurable parameters for number
of users (interrupts it can generate out towards processors)
and number of fifos (the base unidirectional h/w communication
channel). This data cannot be read from any registers, and so
has been added to the platform data.
This data together with the interrupt-type configuration can be
used in properly figuring out the number of registers to save
and restore in the OMAP mailbox driver code.
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
The OMAP mailbox platform driver code has been cleaned up to
remove the dependencies with soc.h in preparation for moving
the mailbox code to drivers folder.
The code relied on cpu_is_xxx/soc_is_xxx macros previously to
pick the the right set of mailbox devices and register with the
mailbox driver. This data is now represented in a concise format
and moved to the respective omap_hwmod data files and published
to the driver through the platform data.
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
OMAP UART IP needs software control for slave idle modes based on functional
state of the IP. i.e The IP slave idle settings should be set to 'noidle' when
being used and then put back to 'smart_idle' when unused. Currently this is
handled by the driver with function pointers implemented in platform code.
This however breaks in case of device tree because of missing idle handling
APIs.
Previous patches in this series added a flag HWMOD_SWSUP_SIDLE_ACTIVE which
takes care of the mentioned requirement. Hence add the flag for all UART IPs
to take advantage of feature supported by framework.
Subsequent patches removes the slave idle handling from driver code.
Tested-by: Vaibhav Bedia <vaibhav.bedia@ti.com>
Tested-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org> # OMAP4/Panda
Signed-off-by: Paul Walmsley <paul@pwsan.com>
information. Also enable few HW errata workarounds for omap4.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=bKnC
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.10/soc-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/soc
From Tony Lindgren <tony@atomide.com>:
Changes needed for enabling SOC_BUS for the SoC revision
information. Also enable few HW errata workarounds for omap4.
* tag 'omap-for-v3.10/soc-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (236 commits)
ARM: OMAP4: Enable fix for Cortex-A9 erratas
ARM: OMAP2+: Export SoC information to userspace
ARM: OMAP2+: SoC name and revision unification
ARM: OMAP2+: Move common part of late init into common function
Includes an update to Linux 3.9-rc6
Conflicts:
arch/arm/mach-omap2/cclock44xx_data.c
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Convert the device data for the OMAP3 AES crypto IP
from explicit platform_data to hwmod.
CC: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
[paul@pwsan.com: fixed lines causing sparse warnings]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Convert the device data for the OMAP3 SHAM2 (SHA1/MD5) crypto IP
from explicit platform_data to hwmod.
CC: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
[paul@pwsan.com: updated to use per-SoC registration lists for GP-only hwmods;
fixed lines causing sparse warnings]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
For some unknown reason, allowing hwmod to control MIDLEMODE causes
core_pwrdm to not hit idle states for musb in DM3730 at least.
I've verified that setting any MIDLEMODE value other than "force
standby" before enabling the device causes subsequent suspend
attempts to fail with core_pwrdm not entering idle states, even
if the driver is unloaded and "force standby" is restored before
suspend attempt. To recover from this, soft reset can be used, but
that's not suitable solution for suspend.
Keeping the register set at force standby (reset value) makes it work
and device still functions properly, as musb has driver-controlled
OTG_FORCESTDBY register that controls MSTANDBY signal.
Note that TI PSP kernels also have similar workarounds.
This patch also fixes HWMOD_SWSUP_MSTANDBY documentation to match the
actual flag name.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
According to Mark Greer, on OMAP AM3517/3505 chips, the EMAC is unable
to wake the ARM up from WFI:
http://www.spinics.net/lists/arm-kernel/msg174734.html
Further troubleshooting was unable to narrow the problem down. So we
don't have much choice other than to block WFI when the EMAC is active
with the HWMOD_BLOCK_WFI flag.
Based on Mark's original patch. We're removing the omap_device-based
pm_lats code, so a different approach was needed.
This third version contains some corrections thanks to Mark's review.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Mark A. Greer <mgreer@animalcreek.com>
Acked-by: Mark A. Greer <mgreer@animalcreek.com>
Pull i2c-embedded changes from Wolfram Sang:
- CBUS driver (an I2C variant)
- continued rework of the omap driver
- s3c2410 gets lots of fixes and gains pinctrl support
- at91 gains DMA support
- the GPIO muxer gains devicetree probing
- typical fixes and additions all over
* 'i2c-embedded/for-next' of git://git.pengutronix.de/git/wsa/linux: (45 commits)
i2c: omap: Remove the OMAP_I2C_FLAG_RESET_REGS_POSTIDLE flag
i2c: at91: add dma support
i2c: at91: change struct members indentation
i2c: at91: fix compilation warning
i2c: mxs: Do not disable the I2C SMBus quick mode
i2c: mxs: Handle i2c DMA failure properly
i2c: s3c2410: Remove recently introduced performance overheads
i2c: ocores: Move grlib set/get functions into #ifdef CONFIG_OF block
i2c: s3c2410: Add fix for i2c suspend/resume
i2c: s3c2410: Fix code to free gpios
i2c: i2c-cbus-gpio: introduce driver
i2c: ocores: Add support for the GRLIB port of the controller and use function pointers for getreg and setreg functions
i2c: ocores: Add irq support for sparc
i2c: omap: Move the remove constraint
ARM: dts: cfa10049: Add the i2c muxer buses to the CFA-10049
i2c: s3c2410: do not special case HDMIPHY stuck bus detection
i2c: s3c2410: use exponential back off while polling for bus idle
i2c: s3c2410: do not generate STOP for QUIRK_HDMIPHY
i2c: s3c2410: grab adapter lock while changing i2c clock
i2c: s3c2410: Add support for pinctrl
...
This branch contains a largeish set of updates of power management and
clock setup. The bulk of it is for OMAP/AM33xx platforms, but also a
few around hotplug/suspend/resume on Exynos.
It includes a split-up of some of the OMAP clock data into separate
files which adds to the diffstat, but gross delta is fairly reasonable.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=h2Qo
-----END PGP SIGNATURE-----
Merge tag 'pm-merge' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC power management and clock changes from Olof Johansson:
"This branch contains a largeish set of updates of power management and
clock setup. The bulk of it is for OMAP/AM33xx platforms, but also a
few around hotplug/suspend/resume on Exynos.
It includes a split-up of some of the OMAP clock data into separate
files which adds to the diffstat, but gross delta is fairly reasonable."
* tag 'pm-merge' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (60 commits)
ARM: OMAP: Move plat-omap/dma-omap.h to include/linux/omap-dma.h
ASoC: OMAP: mcbsp fixes for enabling ARM multiplatform support
watchdog: OMAP: fixup for ARM multiplatform support
ARM: EXYNOS: Add flush_cache_all in suspend finisher
ARM: EXYNOS: Remove scu_enable from cpuidle
ARM: EXYNOS: Fix soft reboot hang after suspend/resume
ARM: EXYNOS: Add support for rtc wakeup
ARM: EXYNOS: fix the hotplug for Cortex-A15
ARM: OMAP2+: omap_device: Correct resource handling for DT boot
ARM: OMAP2+: hwmod: Add possibility to count hwmod resources based on type
ARM: OMAP2+: hwmod: Add support for per hwmod/module context lost count
ARM: OMAP2+: PRM: initialize some PRM functions early
ARM: OMAP2+: voltage: fixup oscillator handling when CONFIG_PM=n
ARM: OMAP4: USB: power down MUSB PHY during boot
ARM: OMAP2+: clock: Cleanup !CONFIG_COMMON_CLK parts
ARM: OMAP2xxx: clock: drop obsolete clock data
ARM: OMAP2: clock: Cleanup !CONFIG_COMMON_CLK parts
ARM: OMAP3+: DPLL: drop !CONFIG_COMMON_CLK sections
ARM: AM33xx: clock: drop obsolete clock data
ARM: OMAP3xxx: clk: drop obsolete clock data
...
enabled. Unfortunately the DMA header patch had to be redone
to avoid adding new multiplatform specific include paths, the
other patches are just trivial compile fixes.
Note that this does not yet contain the necessary Kconfig
changes as we are still waiting for some drivers to get
fixed up first.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=w+UN
-----END PGP SIGNATURE-----
Merge tag 'tags/omap-for-v3.8/cleanup-multiplatform-no-clock-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/pm2
From Tony Lindgren:
Remaining patches to allow omap2+ to build with multiplatform
enabled. Unfortunately the DMA header patch had to be redone
to avoid adding new multiplatform specific include paths, the
other patches are just trivial compile fixes.
Note that this does not yet contain the necessary Kconfig
changes as we are still waiting for some drivers to get
fixed up first.
* tag 'tags/omap-for-v3.8/cleanup-multiplatform-no-clock-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP: Move plat-omap/dma-omap.h to include/linux/omap-dma.h
ASoC: OMAP: mcbsp fixes for enabling ARM multiplatform support
watchdog: OMAP: fixup for ARM multiplatform support
Conflicts due to surrounding changes in:
arch/arm/mach-omap2/omap_hwmod_2420_data.c
arch/arm/mach-omap2/omap_hwmod_2430_data.c
Signed-off-by: Olof Johansson <olof@lixom.net>
This is needed for the multiplatform kernels as the plat
and mach headers cannot be included.
These changes were agreed to be merged via the arm-soc
tree by Joerg and Ohad as these will cause some merge
conflicts with the other related clean-up branches.
So omap-for-v3.8/cleanup-headers-iommu should be added
as one of the depends branches for arm-soc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=yFcc
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.8/cleanup-headers-iommu-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/cleanup
From Tony Lindgren:
Move most of remaining omap iommu code to drivers/iommu.
This is needed for the multiplatform kernels as the plat
and mach headers cannot be included.
These changes were agreed to be merged via the arm-soc
tree by Joerg and Ohad as these will cause some merge
conflicts with the other related clean-up branches.
So omap-for-v3.8/cleanup-headers-iommu should be added
as one of the depends branches for arm-soc.
* tag 'omap-for-v3.8/cleanup-headers-iommu-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Move iommu/iovmm headers to platform_data
ARM: OMAP2+: Make some definitions local
ARM: OMAP2+: Move iommu2 to drivers/iommu/omap-iommu2.c
ARM: OMAP2+: Move plat/iovmm.h to include/linux/omap-iommu.h
ARM: OMAP2+: Move iopgtable header to drivers/iommu/
ARM: OMAP: Merge iommu2.h into iommu.h
Conflicts due to surrounding changes fixed up in:
arch/arm/mach-omap2/omap_hwmod_44xx_data.c
drivers/media/platform/omap3isp/ispvideo.c
Signed-off-by: Olof Johansson <olof@lixom.net>
Based on earlier discussions[1] we attempted to find a suitable
location for the omap DMA header in commit 2b6c4e73 (ARM: OMAP:
DMA: Move plat/dma.h to plat-omap/dma-omap.h) until the conversion
to dmaengine is complete.
Unfortunately that was before I was able to try to test compile
of the ARM multiplatform builds for omap2+, and the end result
was not very good.
So I'm creating yet another all over the place patch to cut the
last dependency for building omap2+ for ARM multiplatform. After
this, we have finally removed the driver dependencies to the
arch/arm code, except for few drivers that are being worked on.
The other option was to make the <plat-omap/dma-omap.h> path
to work, but we'd have to add some new header directory to for
multiplatform builds.
Or we would have to manually include arch/arm/plat-omap/include
again from arch/arm/Makefile for omap2+.
Neither of these alternatives sound appealing as they will
likely lead addition of various other headers exposed to the
drivers, which we want to avoid for the multiplatform kernels.
Since we already have a minimal include/linux/omap-dma.h,
let's just use that instead and add a note to it to not
use the custom omap DMA functions any longer where possible.
Note that converting omap DMA to dmaengine depends on
dmaengine supporting automatically incrementing the FIFO
address at the device end, and converting all the remaining
legacy drivers. So it's going to be few more merge windows.
[1] https://patchwork.kernel.org/patch/1519591/#
cc: Russell King <linux@arm.linux.org.uk>
cc: Kevin Hilman <khilman@ti.com>
cc: "Benoît Cousson" <b-cousson@ti.com>
cc: Herbert Xu <herbert@gondor.apana.org.au>
cc: "David S. Miller" <davem@davemloft.net>
cc: Vinod Koul <vinod.koul@intel.com>
cc: Dan Williams <djbw@fb.com>
cc: Mauro Carvalho Chehab <mchehab@infradead.org>
cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
cc: David Woodhouse <dwmw2@infradead.org>
cc: Kyungmin Park <kyungmin.park@samsung.com>
cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
cc: Hans Verkuil <hans.verkuil@cisco.com>
cc: Vaibhav Hiremath <hvaibhav@ti.com>
cc: Lokesh Vutla <lokeshvutla@ti.com>
cc: Rusty Russell <rusty@rustcorp.com.au>
cc: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
cc: Afzal Mohammed <afzal@ti.com>
cc: linux-crypto@vger.kernel.org
cc: linux-media@vger.kernel.org
cc: linux-mtd@lists.infradead.org
cc: linux-usb@vger.kernel.org
cc: linux-fbdev@vger.kernel.org
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The OMAP_I2C_FLAG_RESET_REGS_POSTIDLE is not used anymore
in the i2c driver. Remove the flag.
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Move iommu/iovmm headers from plat/ to platform_data/ as part of the
single zImage work.
Partially based on an earlier version by Ido Yariv <ido@wizery.com>.
Cc: Ido Yariv <ido@wizery.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Omar Ramirez Luna <omar.luna@linaro.org>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Ohad Ben-Cohen <ohad@wizery.com>
Acked-by: Joerg Roedel <joro@8bytes.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The commit [i2c: omap: use revision check for OMAP_I2C_FLAG_APPLY_ERRATA_I207]
uses the revision id instead of the flag. So the flag can be safely removed.
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Currently OMAP2+ devices are using the function __omap_dm_timer_reset() to
configure the clock-activity, idle, wakeup-enable and auto-idle fields in the
timer OCP_CFG register. The name of the function is mis-leading because this
function does not actually perform a reset of the timer.
For OMAP2+ devices, HWMOD is responsible for reseting and configuring the
timer OCP_CFG register. Therefore, do not use __omap_dm_timer_reset() for
OMAP2+ devices and rely on HWMOD. Furthermore, some timer instances do not
have the fields clock-activity, wakeup-enable and auto-idle and so this
function could configure the OCP_CFG register incorrectly.
Currently HWMOD is not configuring the clock-activity field in the OCP_CFG
register for timers that have this field. Commit 0f0d080 (ARM: OMAP: DMTimer:
Use posted mode) configures the clock-activity field to keep the f-clk enabled
so that the wake-up capability is enabled. Therefore, add the appropriate flags
to the timer HWMOD structures to configure this field in the same way.
For OMAP2/3 devices all dmtimers have the clock-activity field, where as for
OMAP4 devices, only dmtimer 1, 2 and 10 have the clock-activity field.
Verified on OMAP2420 H4, OMAP3430 Beagle and OMAP4430 Panda that HWMOD is
configuring the dmtimer OCP_CFG register as expected for clock-events timer.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
For OMAP2/3 devices, the HWMOD data does not define a software reset status
field for the DMTIMERs. Therefore, when HWMOD performs a soft-reset of the
DMTIMER we don't check and wait for the reset to complete. For OMAP2/3 devices,
the software reset status for a DMTIMER can be read from bit 0 of the DMTIMER
TISTAT register (referred to as the SYSS register in HWMOD). Add the
appropriate HWMOD definitions so that HWMOD will check the software reset
status when performing a software reset of the DMTIMER.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Currently, the OMAP3 HWMOD data defines two TIOCP_CFG register structures
(referred to as the SYSC register in the HWMOD data) where timers 1, 2 and 10
use one of the defintions and the other timers use the other definition. For
OMAP3 devices the structure of the DMTIMER TIOCP_CFG register is the same for
all 12 instances of the DMTIMER. Please note that this is a difference between
OMAP3 and OMAP4 and could be the source of the confusion.
For OMAP3 devices, the DMTIMER TIOCP_CFG register has the fields,
clock-activity, emufree, idlemode, enwakeup, softreset and autoidle for all
12 timers. Therefore, remove one of the SYSC register definitions for the
DMTIMERs and ensure the appropriate register fields are defined for all
DMTIMERs.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
For omap1, we'll keep mach/serial.h around for 8250.c hardware
workarounds. For omap2+, we no longer need mach/serial.h and
can make it local to mach-omap2.
Signed-off-by: Tony Lindgren <tony@atomide.com>
There's no need to keep the device related things in the
common i2c.c as omap2+ is using hwmod. Split the code to
mach-omap1 and mach-omap2 parts and only leave common
code to plat-omap/i2c.c.
Note that as omap1 only has one i2c controller, we can
now remove the old device related macros.
Reviewed-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Move plat/dma.h to plat-omap/dma-omap.h as part of single
zImage work
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Similar to omap1, some of the omap2+ dma channel definitions are
used by some drivers. For moving omap2+ dma channel definitions
to mach-omap2/, the used ones should be defined locally to driver.
Drivers can eliminate it using DT, platform data, or IORESOURCE_DMA
And moving omap2+ DMA channel definitions to mach-omap2
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We need to remove this from plat for ARM common zImage
support.
Also remove includes not needed by the omap_hsmmc.c driver.
Cc: linux-mmc@vger.kernel.org
Acked-by: Chris Ball <cjb@laptop.org>
Acked-by: Venkatraman S <svenkatr@ti.com>
[tony@atomide.com: fold in removal of unused driver includes]
Signed-off-by: Tony Lindgren <tony@atomide.com>
From Paul Walmsley <paul@pwsan.com> via Tony Lindgren:
Some OMAP fixes for the 3.7 merge window, fixing mismerges, branch
integration issues, and bugs after the arm-soc merges.
* tag 'omap-for-v3.7-rc1/fixes-hwmod-clock-signed-v3' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP4/AM335x: hwmod: fix disable_module regression in hardreset handling
ARM: OMAP3: fix workaround for EMU clockdomain
ARM: OMAP: omap3evm: fix new sparse warning
ARM: OMAP2+: hwmod data: Fix PMU interrupt definitions
ARM: am33xx: clk: Update clkdev table to add mcasp alias
This patch adds a missing hwmod entry for the HDQ/1-Wire module present
in the AM3505/17 CPUs.
This restores 1-Wire support to our AM3505 boards. We think it probably
stopped working with commit 96b1b29d37
ARM: OMAP2+: HDQ1W: use omap_device
Signed-off-by: Raphael Assenat <raph@8d.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 7d7e1eb (ARM: OMAP2+: Prepare for irqs.h removal) and commit ec2c082
(ARM: OMAP2+: Remove hardcoded IRQs and enable SPARSE_IRQ) updated the way
interrupts for OMAP2/3 devices are defined in the HWMOD data structures to
being an index plus a fixed offset (defined by OMAP_INTC_START). The definition
of the PMU interrupts on OMAP2/3 devices is missing the OMAP_INTC_START offset
and so this is causing the allocation of PMU interrupts to fail on OMAP2/3
devices. So add the offset to fix this.
This is patch is based upon Tony's master branch for OMAP.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Merge in the late Kirkwood branch with the OMAP late branch for upstream
submission.
Final contents described in shared tag.
Fixup remove/change conflicts in arch/arm/mach-omap2/devices.c and
drivers/spi/spi-omap2-mcspi.c.
Signed-off-by: Olof Johansson <olof@lixom.net>
OMAP4460 and OMAP4470 devices have dedicated PMU interrupts and so add these
interrupts to the MPU HWMOD so we can use these for PMU events on these
devices. The PMU interrupts need to be the first interrupts in the array of
interrupts as the ARM PMU driver assumes this.
By using these dedicated interrupts we only need to enable the MPU and DEBUG
sub-systems for PMU to work. This is different to OMAP4430 that did not have
dedicated interrupts and required other power domains in addition to the DEBUG
sub-system to be enabled so we could route the PMU events to the CTI interrupts.
Hence, OMAP4460 and OMAP4470 devices can use the same list of HWMODs to create
the PMU device that is using by OMAP3.
Cc: Ming Lei <ming.lei@canonical.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@ti.com>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
[paul@pwsan.com: updated to apply]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Convert OMAP2/3 devices to use HWMOD for creating a PMU device. To support PMU
on OMAP2 devices we only need to use MPU sub-system and so we can simply use
the MPU HWMOD to create the PMU device. To support PMU on OMAP3 devices, we need
to use the MPU and DEBUG sub-systems and so use these HWMODs to create the PMU
device for OMAP3.
The MPU HWMOD for OMAP2/3 devices is currently missing the PMU interrupt and so
add the PMU interrupt to the MPU HWMOD for these devices.
This change also moves the PMU code out of the mach-omap2/devices.c files into
its own pmu.c file as suggested by Kevin Hilman to de-clutter devices.c.
Cc: Ming Lei <ming.lei@canonical.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@ti.com>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
[paul@pwsan.com: fixed checkpatch messages; updated to apply; dropped old-style
initial filename line in header comments]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
To enable PMU with runtime PM support on OMAP3 devices we need to be able to
dynamically enable and disable the debug sub-system at runtime. By adding HWMOD
data for the debug sub-system for OMAP3, we can build the PMU device using the
debug sub-system HWMOD and control this power domain using runtime PM.
Reviewed-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
[paul@pwsan.com: updated to apply; added L4-EMU address space]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Some instances of the DMTIMER peripheral on OMAP devices have the ability
to interrupt the on-chip DSP in addition to the ARM CPU. Add a DMTIMER
attribute to indicate which timers can interrupt the DSP. By using the
omap_dm_timer_request_by_cap() API, driver will now be able to allocate
a DMTIMER that can interrupt the DSP based upon this attribute and not require
the driver to know which instance has this capability.
DMTIMERs that have the ability to interrupt the DSP on OMAP devices are as
follows ...
- OMAP1 (OMAP5912/16xx/17xx) devices - All 8 DMTIMERs
- OMAP2/3/4 devices - DMTIMERs 5-8
Please note that for OMAP3+, timer8 has the ability to interrupt the DSP and
generate a PWM output.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add gpmc hwmod and associated interconnect data
Signed-off-by: Afzal Mohammed <afzal@ti.com>
[paul@pwsan.com: added comments to the use of HWMOD_INIT_NO_RESET]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add mmu hwmod data for iva and isp.
Due to compatibility an ifdef CONFIG_OMAP_IOMMU_IVA2 needs to be
propagated (previously on iommu resource info) to hwmod data in OMAP3,
so users of iommu and tidspbridge can avoid issues of two modules
managing mmu data/irqs/resets; this until tidspbridge can be migrated
to iommu framework.
Cc: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Omar Ramirez Luna <omar.luna@linaro.org>
[paul@pwsan.com: fixed some kerneldoc and whitespace; ISP MMUs not present
on AM35xx so restricted these hwmods to 34xx/36xx]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
SAD2D stands for the die to die interface, and is used for communicating
with the optional stacked modem. This hwmod is added in preparation for
the d2d_idle move from pm34xx.c to hwmod data.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
[paul@pwsan.com: SAD2D presumably doesn't exist on non-OMAP34xx/OMAP36xx,
so only add it to the OMAP34xx/OMAP36xx lists]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
twl-core driver and to fix omap1_defconfig compile when
led driver changes and omap sparse IRQ changes are merged
together. Also fix warnings for omaps not using pinctrl
framework yet.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=omEP
-----END PGP SIGNATURE-----
Merge tag 'cleanup-fixes-for-v3.7' into test_v3.6-rc6_ocb3.7_cff3.7_odaf3.7
These fixes are needed to fix non-omap build breakage for
twl-core driver and to fix omap1_defconfig compile when
led driver changes and omap sparse IRQ changes are merged
together. Also fix warnings for omaps not using pinctrl
framework yet.
header files local where possible to get us closer to supporting
the ARM single zImage. After these changes mach includes are
pretty much out of the way for omap2+, but still lots of manual
work remains to sort through the remaining plat includes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=TZVo
-----END PGP SIGNATURE-----
Merge tag 'omap-cleanup-local-headers-for-v3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/cleanup
From Tony Lindgren:
This branch contains mostly scripted changes to make omap
header files local where possible to get us closer to supporting
the ARM single zImage. After these changes mach includes are
pretty much out of the way for omap2+, but still lots of manual
work remains to sort through the remaining plat includes.
* tag 'omap-cleanup-local-headers-for-v3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (26 commits)
ARM: OMAP2+: Make omap4-keypad.h local
ARM: OMAP2+: Make l4_3xxx.h local
ARM: OMAP2+: Make l4_2xxx.h local
ARM: OMAP2+: Make l3_3xxx.h local
ARM: OMAP2+: Make l3_2xxx.h local
ARM: OMAP1: Move irda.h from plat to mach
ARM: OMAP2+: Make hdq1w.h local
ARM: OMAP2+: Make gpmc-smsc911x.h local
ARM: OMAP2+: Make gpmc-smc91x.h local
ARM: OMAP1: Move flash.h from plat to mach
ARM: OMAP2+: Make debug-devices.h local
ARM: OMAP1: Move board-voiceblue.h from plat to mach
ARM: OMAP1: Move board-sx1.h from plat to mach
ARM: OMAP2+: Make omap-wakeupgen.h local
ARM: OMAP2+: Make omap-secure.h local
ARM: OMAP2+: Make ctrl_module_wkup_44xx.h local
ARM: OMAP2+: Make ctrl_module_pad_wkup_44xx.h local
ARM: OMAP2+: Make ctrl_module_pad_core_44xx.h local
ARM: OMAP2+: Make ctrl_module_core_44xx.h local
ARM: OMAP2+: Make board-rx51.h local
...
The Tegra code-base has contained both a legacy DMA and a dmaengine
driver since v3.6-rcX. This series flips Tegra's defconfig to enable
dmaengine rather than the legacy driver, and removes the legacy driver
and all client code.
The branch is based on v3.6-rc6 in order to pick up a bug-fix to the
ASoC Tegra PCM driver that's required for audio to work correctly when
using dmaengine.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=4eRL
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-3.7-dmaengine' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into next/cleanup
ARM: tegra: switch to dmaengine
The Tegra code-base has contained both a legacy DMA and a dmaengine
driver since v3.6-rcX. This series flips Tegra's defconfig to enable
dmaengine rather than the legacy driver, and removes the legacy driver
and all client code.
* tag 'tegra-for-3.7-dmaengine' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra:
ASoC: tegra: remove support of legacy DMA driver based access
spi: tegra: remove support of legacy DMA driver based access
ARM: tegra: apbio: remove support of legacy DMA driver based access
ARM: tegra: dma: remove legacy APB DMA driver
ARM: tegra: config: enable dmaengine based APB DMA driver
+ sync to 3.6-rc6
Platform data for device drivers should be defined in
include/linux/platform_data/*.h, not in the architecture
and platform specific directories.
This moves such data out of the omap include directories
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: "Benoît Cousson" <b-cousson@ti.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Ohad Ben-Cohen <ohad@wizery.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Omar Ramirez Luna <omar.ramirez@ti.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Jarkko Nikula <jarkko.nikula@bitmer.com>
Cc: Liam Girdwood <lrg@ti.com>
Cc: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Cc: Jean Pihet <j-pihet@ti.com>
Cc: J Keerthy <j-keerthy@ti.com>
Cc: linux-omap@vger.kernel.org
As the plat and mach includes need to disappear for single zImage work,
we need to remove plat/hardware.h.
Do this by splitting plat/hardware.h into omap1 and omap2+ specific files.
The old plat/hardware.h already has omap1 only defines, so it gets moved
to mach/hardware.h for omap1. For omap2+, we use the local soc.h
that for now just includes the related SoC headers to keep this patch more
readable.
Note that the local soc.h still includes plat/cpu.h that can be dealt
with in later patches. Let's also include plat/serial.h from common.h for
all the board-*.c files. This allows making the include files local later
on without patching these files again.
Note that only minimal changes are done in this patch for the
drivers/watchdog/omap_wdt.c driver to keep things compiling. Further
patches are needed to eventually remove cpu_is_omap usage in the drivers.
Also only minimal changes are done to sound/soc/omap/* to remove the
unneeded includes and to define OMAP44XX_MCPDM_L3_BASE locally so there's
no need to include omap44xx.h.
While at it, also sort some of the includes in the standard way.
Cc: linux-watchdog@vger.kernel.org
Cc: alsa-devel@alsa-project.org
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Jarkko Nikula <jarkko.nikula@bitmer.com>
Cc: Liam Girdwood <lrg@ti.com>
Acked-by: Wim Van Sebroeck <wim@iguana.be>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
As the interrupts should only be defined in the platform_data, and
eventually coming from device tree, there's no need to define them
in header files.
Let's remove the hardcoded references to irqs.h and fix up the includes
so we don't rely on headers included in irqs.h. Note that we're
defining OMAP_INTC_START as 0 to the interrupts. This will be needed
when we enable SPARSE_IRQ. For some drivers we need to add
#include <plat/cpu.h> for now until these drivers are fixed to
remove cpu_is_omapxxxx() usage.
While at it, sort som of the includes the standard way, and add
the trailing commas where they are missing in the related data
structures.
Note that for drivers/staging/tidspbridge we just define things
locally.
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This way we can remove includes of plat/gpio.h which won't work
with the single zImage support.
Note that we also remove the cpu_class_is_omap2() check
in gpio-omap.c as the drivers should not call it as we need to
make it local to arch/arm/mach-omap2 for single zImage support.
While at it, arrange the related includes in the standard way.
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: linux-mtd@lists.infradead.org
Cc: alsa-devel@alsa-project.org
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
IVA2 hwmod resets were missing the status bit offsets. Also, as the
hwmod itself didn't have prcm info at all, resetting iva hwmod was
accessing some bogus memory addresses. Added both infos to fix this.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
These are various power management related changes, mainly concerning
cpuidle on i.MX and OMAP, as well as a the move of the omap smartreflex
driver to live in the power subsystem.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIVAwUAUA2dhWCrR//JCVInAQLuqRAA1FxxzAMTESs3/rpjnQmZUUKef4SuJwY2
GBenXFLY5PlxgcrwTbKwepapu8IWfmw171+tRrrMWvQgtBwa+SefwFCaLcRkvRrs
kNAHIVI+Gqm4/m6d+WC+ymJLOZdkcTHES+40eycxcjiIElGEMtiW5/qwh060GAgC
YxtjoN9BKegjsDLPZdZghO855YUV8CKEg+q5kIYW0Q3Ci0POGvOhgvbI61K5w8z7
fTdbFRDRBqy0BEx9noKTu8XIB/inwlyUY7N3bAv494TsU48kxMIb95FdSGiY/0yV
1883wCacBYBNemWRvWBHNilSsDcuDmM3yNvdwi3JvQnzFBPc8uyze9wbPFOW4aQd
Vhf+g8hjuHkw1xreWpO+nREysOjiiSzRUci2nT6aAQTcpWCacVTJ5sW7KOQ63nrH
OQpe/fvm/qT8FKPDh/lcrqIUKrHfeFjZx7XlYjw7j0ZL+99mIpwuOql18mQee9G5
OV6c0rfgeTnGLdc1kOlLPElkXe7SQ/GJK1JI1mA5BNYJlVKx+o0qVlcnRzY6bWaP
dmSIA+9Bs/fglvmAQHT3u68zn5KfoTbnJWb0v5PQJfitEBdlugKG8nF9mVRIX70X
EygOta8vApF9N20WhE2TLLaDhlrOmd4bOtRVdoO8pDVN/hsWIylnEu952ZBSZg3U
9wF0Ydy2LP4=
=tgT5
-----END PGP SIGNATURE-----
Merge tag 'pm' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc power management changes from Arnd Bergmann:
"These are various power management related changes, mainly concerning
cpuidle on i.MX and OMAP, as well as a the move of the omap
smartreflex driver to live in the power subsystem."
Fix up conflicts in arch/arm/mach-{imx/mach-imx6q.c,omap2/prm2xxx_3xxx.h}
* tag 'pm' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (37 commits)
ARM: OMAP2+: PM: fix IRQ_NOAUTOEN removal by mis-merge
ARM: OMAP2+: do not allow SmartReflex to be built as a module
ARM: OMAP2: Use hwmod to initialize mmc for 2420
ARM: OMAP3: PM: cpuidle: optimize the clkdm idle latency in C1 state
ARM: OMAP3: PM: cpuidle: optimize the PER latency in C1 state
ARM: OMAP3: PM: cpuidle: default to C1 in next_valid_state
ARM: OMAP3: PM: cleanup cam_pwrdm leftovers
ARM: OMAP3: PM: call pre/post transition per powerdomain
ARM: OMAP2+: powerdomain: allow pre/post transtion to be per pwrdm
ARM: OMAP3: PM: Remove IO Daisychain control from cpuidle
ARM: OMAP3PLUS: hwmod: reconfigure IO Daisychain during hwmod mux
ARM: OMAP3+: PRM: Enable IO wake up
ARM: OMAP4: PRM: Add IO Daisychain support
ARM: OMAP3: PM: Move IO Daisychain function to omap3 prm file
ARM: OMAP3: PM: correct enable/disable of daisy io chain
ARM: OMAP2+: PRM: fix compile for OMAP4-only build
W1: OMAP HDQ1W: use runtime PM
ARM: OMAP2+: HDQ1W: use omap_device
W1: OMAP HDQ1W: use 32-bit register accesses
W1: OMAP HDQ1W: allow driver to be built on all OMAP2+
...
This contains two branches dealing with timers, one for the picoxcell
platform that is now using DT with the platform-independent
dw_apb_timer driver. The other change is for the omap-specific
dmtimer driver.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=2bZ2
-----END PGP SIGNATURE-----
Merge tag 'timer' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc timer updates from Arnd Bergmann:
"This contains two branches dealing with timers, one for the picoxcell
platform that is now using DT with the platform-independent
dw_apb_timer driver. The other change is for the omap-specific
dmtimer driver."
* tag 'timer' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
clocksource: dw_apb_timer: Add common DTS glue for dw_apb_timer
ARM: OMAP2+: Simplify dmtimer clock aliases
ARM: OMAP2+: Move dmtimer clock set function to dmtimer driver
ARM: OMAP1: Fix dmtimer support
ARM: OMAP: Add flag to indicate if a timer needs a manual reset
ARM: OMAP: Remove timer function pointer for context loss counter
ARM: OMAP: Remove loses_context variable from timer platform data
ARM: OMAP2+: Fix external clock support for dmtimers
ARM: OMAP2+: HWMOD: Correct timer device attributes
ARM: OMAP: Add DMTIMER capability variable to represent timer features
ARM: OMAP2+: Add dmtimer platform function to reserve systimers
ARM: OMAP2+: Remove unused max number of timers definition
ARM: OMAP: Remove unnecessary clk structure
These are all boring changes, moving stuff around or renaming things
mostly, and also getting rid of stuff that is duplicate or should
not be there to start with. Platform-wise this is all over the place,
mainly omap, samsung, at91, imx and tegra.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=4zvd
-----END PGP SIGNATURE-----
Merge tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull general arm-soc cleanups from Arnd Bergmann:
"These are all boring changes, moving stuff around or renaming things
mostly, and also getting rid of stuff that is duplicate or should not
be there to start with. Platform-wise this is all over the place,
mainly omap, samsung, at91, imx and tegra."
Resolve trivial conflict in arch/arm/mach-omap2/clockdomains3xxx_data.c
* tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (67 commits)
ARM: clps711x: Remove the setting of the time
ARM: clps711x: Removed superfluous transform virt_to_bus and related functions
ARM: clps711x/p720t: Replace __initcall by .init_early call
ARM: S3C24XX: Remove unused GPIO definitions for Openmoko GTA02 board
ARM: S3C24XX: Remove unused GPIO definitions for port J
ARM: S3C24XX: Remove unused GPA, GPE, GPH bank GPIO aliases
ARM: S3C24XX: Convert the touchscreen setup code to common GPIO API
ARM: S3C24XX: Convert the PM code to gpiolib API
ARM: S3C24XX: Convert QT2410 board file to the gpiolib API
ARM: S3C24XX: Convert SMDK board file to the gpiolib API
ARM: S3C24XX: Free the backlight gpio requested in Mini2440 board code
ARM: imx: remove unused pdata from device macros
ARM: imx: Kconfig: Remove IMX_HAVE_PLATFORM_IMX_SSI from MACH_MX25_3DS
ARM: at91: fix new build errors
ARM: at91: add AIC5 support
ARM: at91: remove mach/irqs.h
ARM: at91: sparse irq support
ARM: at91: at91 based machines specify their own irq handler at run time
ARM: at91: remove static irq priorities for sam9x5
ARM: at91: add of irq priorities support
...
Add hwmod support for the EMAC (and MDIO)
ethernet controller that's on the am35x
family of SoC's.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
[paul@pwsan.com: updated subject line; updated to apply on v3.5-rc4;
added comments to hwmod data regarding IPSS]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
During kernel init, the AM3505/AM3517 UART4 cannot complete its softreset:
omap_hwmod: uart4: softreset failed (waited 10000 usec)
This also results in another warning later in the boot process:
omap_hwmod: uart4: enabled state can only be entered from initialized, idle, or disabled state
From empirical observation, the AM35xx UART4 IP block requires either
uart1_fck or uart2_fck to be enabled while UART4 resets. Otherwise
the reset will never complete. So this patch adds uart1_fck as an
optional clock for UART4 and adds the appropriate hwmod flag to cause
uart1_fck to be enabled during the reset process. (The choice of
uart1_fck over uart2_fck was arbitrary.)
Unfortunately this observation raises many questions. Is it necessary
for uart1_fck or uart2_fck to be controlled with uart4_fck for the
UART4 to work correctly? What exactly do the AM35xx UART4 clock
tree and the related PRCM idle management FSMs look like? If anyone
has the ability to answer these questions through empirical functional
testing, or hardware information from the AM35xx designers, it would
be greatly appreciated.
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Kyle Manna <kyle.manna@fuel7.com>
Cc: Mark A. Greer <mgreer@animalcreek.com>
Cc: Ranjith Lohithakshan <ranjithl@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Mark A. Greer <mgreer@animalcreek.com>
Add missing terminators to the arrays of IRQ, DMA, and address space
structure records in the AM35xx UART4 hwmod data. Without these
terminators, the following warnings appear on boot:
omap_uart.3: failed to claim resource 58
omap_device: omap_uart: build failed (-16)
WARNING: at /home/paul/linux/arch/arm/mach-omap2/serial.c:375 omap_serial_init_port+0x198/0x284()
Could not build omap_device for omap_uart: uart4.
Also, AM35xx uart4_fck has an incorrect parent clock pointer. Fix it
and clean up a whitespace issue.
Fix some incorrectly-named macros related to AM35xx UART4.
Cc: Kyle Manna <kyle.manna@fuel7.com>
Cc: Mark A. Greer <mgreer@animalcreek.com>
Cc: Ranjith Lohithakshan <ranjithl@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Mark A. Greer <mgreer@animalcreek.com>
Partially fix the hwmod data for the AM35xx USB OTG hwmod. This
should resolve the following boot warning on AM35xx platforms:
omap_hwmod: am35x_otg_hs: cannot be enabled for reset (3)
While here, also fix the clkdev records, to avoid warnings about
duplicate clock aliases.
The hwmod is also connected to the wrong interconnect. It should be
connected to the IPSS, not the L4 CORE. But that is left for a future
fix, since it probably has a dependency on some hwmod core changes.
Cc: Felipe Balbi <balbi@ti.com>
Cc: Hema HK <hemahk@ti.com>
Cc: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Mark A. Greer <mgreer@animalcreek.com>
Remove the existing alias for pad_fck, prcm_fck from the clock data and
add them as opt_clks to the hwmod data.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The enable/disable module functions are specific to SoCs with
OMAP4-class PRCM. Rather than use cpu_is* checks at runtime inside
the enable/disable module functions, use cpu_is at init time to
initialize function pointers only for SoCs that need them.
NOTE: the cpu_is* check for _enable_module was different than
the one for _disable_module, and this patch uses
cpu_is_omap44xx() for both.
Signed-off-by: Kevin Hilman <khilman@ti.com>
[paul@pwsan.com: moved soc_ops function pointers to be per-kernel rather than
per-hwmod since they do not vary by hwmod; added kerneldoc]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Currently, the dmtimer determines whether an timer can support an external
clock source (sys_altclk) for driving the timer by the IP version. Only
OMAP24xx devices can support an external clock source, but the IP version
between OMAP24xx and OMAP3xxx is common and so this incorrectly indicates
that OMAP3 devices can use an external clock source.
Rather than use the IP version, just let the clock framework handle this.
If the "alt_ck" does not exist for a timer then the clock framework will fail
to find the clock and hence will return an error. By doing this we can eliminate
the "timer_ip_version" variable passed as part of the platform data and simplify
the code.
We can also remove the timer IP version from the HWMOD data because the dmtimer
driver uses the TIDR register to determine the IP version.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix the following issues with the timer device attributes for OMAP2+ devices:
1. For OMAP24xx devices, timers 2-8 have the ALWAYS-ON attribute indicating
that these timers are in an ALWAYS-ON power domain. This is not the case
only timer1 is in an ALWAYS-ON power domain.
2. For OMAP3xxx devices, timers 2-7 have the ALWAYS-ON attribute indicating
that these timers are in an ALWAYS-ON power domain. This is not the case
only timer1 and timer12 are in an ALWAYS-ON power domain.
3. For OMAP3xxx devices, timer12 does not have the ALWAYS-ON attribute but
is in an always-on power domain.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Change the name field value to better reflect the smartreflex
integration in the system.
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: J Keerthy <j-keerthy@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Move the smartreflex header file
(arch/arm/mach-omap2/smartreflex.h) in a new header file
include/linux/power/smartreflex.h.
This change makes the SmartReflex implementation ready for the move
to drivers/.
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: J Keerthy <j-keerthy@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
except for the RNG driver that will be done later on.
As this depends on omap-devel-hwmod-data-for-v3.5 and causes merge
conflict with omap-fixes-non-critical-for-v3.5, this branch is based
on merge of the two.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=w67p
-----END PGP SIGNATURE-----
Merge tag 'omap-cleanup-devices-for-v3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/cleanup2
Changes to split plat-omap/devices.c into mach-omap1 and mach-omap2
except for the RNG driver that will be done later on.
As this depends on omap-devel-hwmod-data-for-v3.5 and causes merge
conflict with omap-fixes-non-critical-for-v3.5, this branch is based
on merge of the two.
By Tony Lindgren (7) and others
via Tony Lindgren (4) and Paul Walmsley (1)
* tag 'omap-cleanup-devices-for-v3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (27 commits)
ARM: OMAP1: Pass dma request lines in platform data to MMC driver
ARM: OMAP: Move omap_mmc_add() to mach-omap1
ARM: OMAP2: Use hwmod to initialize mmc for 2420
ARM: OMAP2+: Move omap_dsp_reserve_sdram_memblock() to mach-omap2
ARM: OMAP1: Move omap_init_uwire to mach-omap1
ARM: OMAP1: Move omap_init_audio() to keep the devices in alphabetical order
ARM: OMAP2+: WDTIMER integration: fix !PM boot crash, disarm timer after hwmod reset
ARM: OMAP2/3: hwmod data: Add 32k-sync timer data to hwmod database
ARM: OMAP4: hwmod_data: Name the common irq for McBSP ports
ARM: OMAP4: hwmod data: I2C: add flag for context restore
ARM: OMAP3: hwmod_data: Rename the common irq for McBSP ports
ARM: OMAP2xxx: hwmod data: add HDQ/1-wire hwmod
ARM: OMAP3: hwmod data: add HDQ/1-wire hwmod
ARM: OMAP2+: hwmod data: add HDQ/1-wire hwmod shared data
ARM: OMAP2+: HDQ1W: add custom reset function
ARM: OMAP2420: hwmod data: Add MMC hwmod data for 2420
arm: omap3: clockdomain data: Remove superfluous commas from gfx_sgx_3xxx_wkdeps[]
ARM: OMAP2+: powerdomain: Get rid off duplicate pwrdm_clkdm_state_switch() API
ARM: OMAP3: clock data: add clockdomain for HDQ functional clock
ARM: OMAP3+: dpll: Configure autoidle mode only if it's supported
...
Currently cpu_is_omap3517() actually detects any device in the AM35x
family (3517 and no-SGX version 3505.) To make it more clear what is
being detected, convert the names from 3517 to AM35xx.
This adds a new soc_is_am35xx() which duplicates the cpu_is_omap3517().
In order to avoid cross-tree dependencies with clock-tree changes,
cpu_is_omap3517() is left until the clock changes are merged,
at which point cpu_is_omap3517() will be completely removed.
Acked-by: Vaibhav Hiremath <hvaibhav@ti.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>
Tested-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
[tony@atomide.com: change to use soc_is_omap instead]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Without runtime PM enabled, hwmod needs to leave all IP blocks in an
enabled state by default so any driver access to the HW will succeed.
This is accomplished by seting the postsetup_state to enabled for all
hwmods during init when runtime PM is disabled.
Currently, we have a special case for WDT in that its postsetup_state
is always set to disabled. This is done so that the WDT is disabled
and the timer is disarmed at boot in case there is no WDT driver.
This also means that when runtime PM is disabled, if a WDT driver *is*
built in the kernel, the kernel will crash on the first access to the
WDT hardware.
We can't simply leave the WDT module enabled, because the timer is
armed by default after reset. That means that if there is no WDT
driver initialzed or loaded before the timer expires, the kernel will
reboot.
To fix this, a custom reset method is added to the watchdog class of
omap_hwmod. This method will *always* disarm the timer after hwmod
reset. The WDT timer then will only be rearmed when/if the driver is
loaded for the WDT. With the timer disarmed by default, we no longer
need a special-case for the postsetup_state of WDT during init, so it
is removed.
Any platforms wishing to ensure the watchdog remains armed across the
entire boot boot can simply disable the reset-on-init feature of the
watchdog hwmod using omap_hwmod_no_setup_reset().
Tested on 3530/Overo, 4430/Panda.
NOTE: on 4430, the hwmod OCP reset does not seem to rearm the timer as
documented in the TRM (and what happens on OMAP3.) I noticed this
because testing the HWMOD_INIT_NO_RESET feature with no driver loaded,
I expected a reboot part way through the boot, but did not see a
reboot. Adding some debug to read the counter, I verified that right
after OCP softreset, the counter is not firing. After writing the
magic start sequence, the timer starts counting. This means that the
timer disarm sequence added here does not seem to be needed for 4430,
but is technically the correct way to ensure the timer is disarmed, so
it is left in for OMAP4.
Special thanks to Paul Walmsley for helping brainstorm ideas to fix
this problem.
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
[paul@pwsan.com: updated the omap2_wd_timer_reset() function in the
wake of commit 3c55c1baff ("ARM:
OMAP2+: hwmod: Revert "ARM: OMAP2+: hwmod: Make omap_hwmod_softreset
wait for reset status""); added kerneldoc; rolled in warning fix from Kevin]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Use 'common' as name for the common irq number in hwmod data for the McBSP
ports. The same name already in use for OMAP2430, and the OMAP4 hwmod data
will be using the same name.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add the HDQ1W hwmod for OMAP34xx, OMAP36xx, and AM3505/3517 devices.
According to the respective TRMs, it doesn't appear to be available for the
816x/814x or the AM335x.
The OCPIF_SWSUP_IDLE flag is added to work around an apparent hardware
bug: the hardware is not taking the CM_FCLKEN*_CORE.EN_HDQ bit into
account when considering whether to go idle:
http://www.spinics.net/lists/linux-omap/msg63576.html
This causes HDQ transfers to fail or become corrupt. Thanks to
NeilBrown for his help diagnosing and testing fixes for this problem.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: NeilBrown <neilb@suse.de>
Tested-by: NeilBrown <neilb@suse.de>
The IVA hwmod data is missing some fields that cause the following
warning on boot:
[ 0.118011] omap_hwmod: iva: cannot be enabled for reset (3)
Fix by encoding the IP block's main functional clock, reset lines, and
clockdomain.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The OMAP3 hwmod data listed iva2_ck as an interface clock between the
IVA and L3. This is incorrect. iva2_ck is not an interface clock.
Since it cannot auto-idle, specifying it here prevents the IVA and at
least one of the CORE clockdomains from going idle, which causes PM
problems such as these upon system suspend:
[ 70.626129] Powerdomain (iva2_pwrdm) didn't enter target state 1
[ 70.626190] Powerdomain (core_pwrdm) didn't enter target state 1
Fix by specifying the actual interface clock in the hwmod data.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Reorganize the hwmod data to declare the IP blocks first and the
interconnects second. This allows us to remove the forward
declarations, which this patch also does. Saves some lines of source
data. While here, take the opportunity to synchronize the order of
the OMAP44xx hwmod data with the autogenerator output -- it's slightly
different due to past mismerges -- and fix a few minor typos and
whitespace problems in the files.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Register interconnect links between IP blocks, rather than the IP
blocks themselves. (The IP blocks will be registered as a side-effect
of registering the links.)
The objective is to reduce the number of lines of static data and
facilitate the sharing of IP block data between different SoCs. These
objectives come at the penalty of increased boot time due to increased
computation.
While here, fix a few whitespace problems and inaccurate variable names.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
GPTIMER12 is attached to the L4 SEC interconnect, not directly to L4 WKUP.
Add the L4 SEC interconnect and attach GPTIMER12 to it.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The OMAP3 hwmod data was missing a DSS->L3 interconnect link for the
OMAP3430 ES1 DSS hwmod. Since the hwmod code and data is being modified
to register interfaces rather than hwmods, this would result in the DSS hwmod
not being registered correctly on OMAP3430ES1.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Commit a52e2ab66d ("ARM: OMAP3: hwmod
data: disable multiblock reads on MMC1/2 on OMAP34xx/35xx <= ES2.1")
didn't link the MMC hwmods to the interconnects correctly. Future
patches will register hwmods by interface, so if this is not fixed,
the MMC IP blocks won't be registered. Update the interface data
records to point to the correct IP blocks.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Some of the 2xxx and 3xxx hwmod data files use the old naming style
for hwmods, ending in a "_hwmod". These names are used by the OMAP
integration code to map hwmods to platform_devices, so they need to be
consistent, or the platform_devices won't be created. Remove the
_hwmod suffix to conform with the rest of the OMAP SoC data.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The clocks for all DSS slave interfaces were recently changed to "dss_ick" on
OMAP2 and OMAP3, this clock can be autoidled by PRCM. The VENC interface
previously had "dss_54m_fck" as it's clock which couldn't be autoidled, and
hence the OCPIF_SWSUP_IDLE flag was needed.
Remove the OCPIF_SWSUP_IDLE flag from VENC interfaces as it's clock is
now "dss_ick". This allows the PRCM hardware to autoidle the VENC
interface clocks when they are not active, rather than relying on the
software to do it, which can keep the interface clocks active
unnecessarily.
Signed-off-by: Archit Taneja <archit@ti.com>
[paul@pwsan.com: add a short description of the fix to the commit log]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add OMAP3 SmartReflex IRQs in hwmod structures. Without these IRQs
being registered the SmartReflex driver will be unable to get the
IRQ numbers to handle notifications.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
To set sr ntarget values for all volt_domain,
volt_table is retrieved by doing a look_up of 'vdd_name'
field from omap_hwmod but voltage domain pointer does not
belong to omap_hwmod and is not used anywhere else.
As a part of voltage layer and SR Layer clean up volt
pointer is removed from omap_hwmod and added in dev
attributes of SR. The value of the field must match
the voltage domain names for the binding to be effective.
Tested on OMAP3630 SDP, OMAP3530 Beagleboard and
OMAP4430 SDP Board.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Shweta Gulati <shweta.gulati@ti.com>
Acked by: Nishanth Menon <nm@ti.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
dss_core has to be initialized before any other DSS hwmod. Currently
this is broken as dss_core is listed in chip/revision specific hwmod
lists while other DSS hwmods are listed in common list which is
registered first.
This patch moves DSS hwmods (except for dss_core) to the separate list
which is registered last to ensure that dss_core is already registered.
This solves the problem with BUG() in L3 interrupt handler on boards
with DSS enabled in bootloader.
The long-term fix to this is to ensure modules are set up in dependency
order in the hwmod core code.
CC: Tomi Valkeinen <tomi.valkeinen@ti.com>
CC: Archit Taneja <archit@ti.com>
CC: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
[paul@pwsan.com: add notes that this is just a temporary workaround until
hwmod dependencies are added]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
dispc's sysc_flags is missing SYSC_HAS_ENAWAKEUP flag. This seems to
cause SYNC_LOST errors from the DSS when the power management is
enabled.
This patch adds the missing SYSC_HAS_ENAWAKEUP flag. Note that there are
other flags missing also (clock activity, DSI's sysc flags), but as they
are not critical, they will be fixed in the next merge window.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Currently OMAP2 and 3 share the same omap_hwmod_class and
omap_hwmod_class_sysconfig for dispc. However, OMAP3 has sysconfig
bits that OMAP2 doesn't have, so we need to split those structs into
OMAP2 and OMAP3 specific versions.
This patch only splits the structs, without changing the contents.
This is a prerequisite for a subsequent fix.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
[paul@pwsan.com: added commit note]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
For I2C clockactivity field is added for OMAP3 and OMAP4 that defines how the
interface (OCP) and functional (system) clocks behave when the I2C module is
idle.
The configuration of the clock activity bit field (per TRM) is as follows:
0x0: Both clocks can be cut off
0x1: Only OCP clock must be kept active; system clock
can be cut off
0x3: Both clocks must be kept active
0x2: Only system clock must be kept active; OCP clock
can be cut off
The patch makes 0x2(CLOCKACT_TEST_ICLK) the default for OMAP3 and OMAP4.
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The HSMMC1/HSMMC2 host controllers on OMAP34xx and
OMAP3503/3515/3525/3530 chips at ES levels prior to 3.0 can't do multiple
block reads[1]. Mark the hwmod data appropriately.
Reported by Dave Hylands <dhylands@gmail.com> and Steve Sakoman
<sakoman@gmail.com>. Thanks to Steve Sakoman for further help
testing this patch.
1. See for example Advisory 2.1.1.128 "MMC: Multiple Block Read
Operation Issue" in _OMAP3530/3525/3515/3503 Silicon Errata_
Revision F (October 2010) (SPRZ278F), available from
http://focus.ti.com/lit/er/sprz278f/sprz278f.pdf
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Dave Hylands <dhylands@gmail.com>
Cc: Steve Sakoman <sakoman@gmail.com>
Following 2 hwmod structures are added
1. usb_host_hs
The hwmod of usbhs with uhh, ehci and ohci base addresses
functional clock and ehci, ohci irqs
2. usb_tll_hs
hwmod of usbhs with the TLL base address and irq.
Signed-off-by: Keshava Munegowda <keshava_mgowda@ti.com>
Reviewed-by: Partha Basak <parthab@india.ti.com>
[paul@pwsan.com: fixed whitespace; removed nonexistent TLL->L3 interface;
added master & slave for L4 CORE->TLL interface; skip registration on
3430ES1; fixed multiline comment style; updated to apply on Tony's cleanup
branch; rebased]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add hwmod support to enable access to UART4 of the AM35xx series of
chips. The UART4 device referenced from the TRM will show up as ttyO3.
This was tested on an AM3505.
Signed-off-by: Kyle Manna <kyle.manna@fuel7.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Seems the commit 7e89098 was overly aggressive in adding iva and mailbox
hwmods so now they are registered twice.
------------[ cut here ]------------
WARNING: at arch/arm/mach-omap2/omap_hwmod.c:1959 omap_hwmod_register+0x104/0x12c()
omap_hwmod: iva: _register returned -22
Modules linked in:
[<c0012aa4>] (unwind_backtrace+0x0/0xec) from [<c002f970>] (warn_slowpath_common+0x4c/0x64)
[<c002f970>] (warn_slowpath_common+0x4c/0x64) from [<c002fa08>] (warn_slowpath_fmt+0x2c/0x3c)
[<c002fa08>] (warn_slowpath_fmt+0x2c/0x3c) from [<c02fdb4c>] (omap_hwmod_register+0x104/0x12c)
[<c02fdb4c>] (omap_hwmod_register+0x104/0x12c) from [<c02fbb44>] (omap3_init_early+0x1c/0x28)
[<c02fbb44>] (omap3_init_early+0x1c/0x28) from [<c02f9580>] (setup_arch+0x6b8/0x7a4)
[<c02f9580>] (setup_arch+0x6b8/0x7a4) from [<c02f754c>] (start_kernel+0x6c/0x264)
[<c02f754c>] (start_kernel+0x6c/0x264) from [<80008040>] (0x80008040)
---[ end trace 1b75b31a2719ed1c ]---
------------[ cut here ]------------
WARNING: at arch/arm/mach-omap2/omap_hwmod.c:1959 omap_hwmod_register+0x104/0x12c()
omap_hwmod: mailbox: _register returned -22
Modules linked in:
[<c0012aa4>] (unwind_backtrace+0x0/0xec) from [<c002f970>] (warn_slowpath_common+0x4c/0x64)
[<c002f970>] (warn_slowpath_common+0x4c/0x64) from [<c002fa08>] (warn_slowpath_fmt+0x2c/0x3c)
[<c002fa08>] (warn_slowpath_fmt+0x2c/0x3c) from [<c02fdb4c>] (omap_hwmod_register+0x104/0x12c)
[<c02fdb4c>] (omap_hwmod_register+0x104/0x12c) from [<c02fbb44>] (omap3_init_early+0x1c/0x28)
[<c02fbb44>] (omap3_init_early+0x1c/0x28) from [<c02f9580>] (setup_arch+0x6b8/0x7a4)
[<c02f9580>] (setup_arch+0x6b8/0x7a4) from [<c02f754c>] (start_kernel+0x6c/0x264)
[<c02f754c>] (start_kernel+0x6c/0x264) from [<80008040>] (0x80008040)
---[ end trace 1b75b31a2719ed1d ]---
Signed-off-by: Felipe Contreras <felipe.contreras@gmail.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Resetting DISPC when a DISPC output is enabled causes the DSS to go into an
inconsistent state. Thus if the bootloader has enabled a display, the hwmod code
cannot reset the DISPC module just like that, but the outputs need to be
disabled first.
Add function dispc_disable_outputs() which disables all active overlay manager
and ensure all frame transfers are completed.
Modify omap_dss_reset() to call this function and clear DSS_CONTROL,
DSS_SDI_CONTROL and DSS_PLL_CONTROL so that DSS is in a clean state when the
DSS2 driver starts.
This resolves the hang issue(caused by a L3 error during boot) seen on the
beagle board C3, which has a factory bootloader that enables display. The issue
is resolved with this patch.
Thanks to Tomi and Sricharan for some additional testing.
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: R, Sricharan <r.sricharan@ti.com>
Signed-off-by: Archit Taneja <archit@ti.com>
[paul@pwsan.com: restructured code, removed omap_{read,write}l(), removed
cpu_is_omap*() calls and converted to dev_attr]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The OMAP3 HWMOD data currently contains these errors with DSS clocks:
- dss_rfbi is missing ick opt-clock, which is needed for RFBI to
calculate timings
- dss_dsi is missing ick and sys_clk
- dss_venc is missing dss_96m_fck opt-clock, which is required on
OMAP3430
- dss_venc's interface and main clocks are wrong, causing VENC to fail
to start
These problems were temporarily fixed with a DSS patch
9ede365aa6 ("HACK: OMAP: DSS2: clk hack
for OMAP2/3"), which can be reverted after this patch (and the similar
patches for other OMAPs).
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
DSS needs all DSS clocks to be enabled to be able to finish reset
properly. Before v3.1-rc1 the omapdss driver was managing clocks and
resets correctly. However, when omapdss started using runtime PM at
v3.1-rc1, the responsibility for the reset moved to HWMOD framework.
HWMOD framework does not currently enable all the DSS clocks when
resetting the DSS hardware. This hasn't caused any problems so far, but
we may just have been lucky.
dss_core's opt-clocks is also missing dss_96m_fck, which is a DSS clock
present only on OMAP3430, and thus required on OMAP3430 to finish the
reset.
This patch sets HWMOD_CONTROL_OPT_CLKS_IN_RESET and adds the dss_96m_fck
opt-clock for dss_core in OMAP3 HWMOD data, fixing the issue.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
[paul@pwsan.com: merged duplicate .flags fields]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Commit d6504acd21 ("OMAP2+: hwmod:
remove OMAP_CHIP*") tests the inverse condition of what it should be
testing for the return value from omap_hwmod_register(). This causes
several IP blocks to not be registered on several OMAP3 family devices.
Fixing that bug also unmasked another bug, originally reported by
Chase Maupin <chase.maupin@ti.com> and then subsequently by Abhilash K
V <abhilash.kv@ti.com>, which caused SmartReflex IP blocks to be
registered on SoCs that don't support them.
Thanks to Russell King - ARM Linux <linux@arm.linux.org.uk> for comments
on a previous version of the patch.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Chase Maupin <chase.maupin@ti.com>
Cc: Abhilash K V <abhilash.kv@ti.com>
Cc: Russell King - ARM Linux <linux@arm.linux.org.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
* 'next/pm' of git://git.linaro.org/people/arnd/arm-soc: (66 commits)
ARM: CSR: PM: use outer_resume to resume L2 cache
ARM: CSR: call l2x0_of_init to init L2 cache of SiRFprimaII
ARM: OMAP: voltage: voltage layer present, even when CONFIG_PM=n
ARM: CSR: PM: add sleep entry for SiRFprimaII
ARM: CSR: PM: save/restore irq status in suspend cycle
ARM: CSR: PM: save/restore timer status in suspend cycle
OMAP4: PM: TWL6030: add cmd register
OMAP4: PM: TWL6030: fix ON/RET/OFF voltages
OMAP4: PM: TWL6030: address 0V conversions
OMAP4: PM: TWL6030: fix uv to voltage for >0x39
OMAP4: PM: TWL6030: fix voltage conversion formula
omap: voltage: add a stub header file for external/regulator use
OMAP2+: VC: more registers are per-channel starting with OMAP5
OMAP3+: voltage: update nominal voltage in voltdm_scale() not VC post-scale
OMAP3+: voltage: rename omap_voltage_get_nom_volt -> voltdm_get_voltage
OMAP3+: voltdm: final removal of omap_vdd_info
OMAP3+: voltage: move/rename curr_volt from vdd_info into struct voltagedomain
OMAP3+: voltage: rename scale and reset functions using voltdm_ prefix
OMAP3+: VP: combine setting init voltage into common function
OMAP3+: VP: remove unused omap_vp_get_curr_volt()
...
Fix up trivial conflict in arch/arm/mach-prima2/l2x0.c (code removal vs
edit)
Removing modules iva, sr1_hwmod, sr2_hwmod, mailbox from
the base omap3xxx_hwmods list, so that they can be excluded
for am35x. This removes quite a few warnings on boot for AM35x.
Signed-off-by: Abhilash K V <abhilash.kv@ti.com>
[paul@pwsan.com: dropped 'mailbox class' comments; updated changelog]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add routines to converts dmtimers to platform devices. The device data
is obtained from hwmod database of respective platform and is registered
to device model after successful binding to driver.
In addition, capability attribute of each of the timers is added in
hwmod database.
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Signed-off-by: Thara Gopinath <thara@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Cousson, Benoit <b-cousson@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Jarkko Nikula