* 'x86-mm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, mm: Unify kernel_physical_mapping_init() API
x86, mm: Allow highmem user page tables to be disabled at boot time
x86: Do not reserve brk for DMI if it's not going to be used
x86: Convert tlbstate_lock to raw_spinlock
x86: Use the generic page_is_ram()
x86: Remove BIOS data range from e820
Move page_is_ram() declaration to mm.h
Generic page_is_ram: use __weak
resources: introduce generic page_is_ram()
The SmartMIPS ASE specifies how Read Inhibit (RI) and eXecute Inhibit
(XI) bits in the page tables work. The upper two bits of EntryLo{0,1}
are RI and XI when the feature is enabled in the PageGrain register.
SmartMIPS only covers 32-bit systems. Cavium Octeon+ extends this to
64-bit systems by continuing to place the RI and XI bits in the top of
EntryLo even when EntryLo is 64-bits wide.
Because we need to carry the RI and XI bits in the PTE, the layout of
the PTE is changed. There is a two instruction overhead in the TLB
refill hot path to get the EntryLo bits into the proper position.
Also the TLB load exception has to probe the TLB to check if RI or XI
caused the exception.
Also of note is that the layout of the PTE bits is done at compile and
runtime rather than statically. In the 32-bit case this allows for
the same number of PFN bits as before the patch as the _PAGE_HUGE is
not supported in 32-bit kernels (we have _PAGE_NO_EXEC and
_PAGE_NO_READ instead of _PAGE_READ and _PAGE_HUGE).
The patch is tested on Cavium Octeon+, but should also work on 32-bit
systems with the Smart-MIPS ASE.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/952/
Patchwork: http://patchwork.linux-mips.org/patch/956/
Patchwork: http://patchwork.linux-mips.org/patch/962/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The soon to follow Read Inhibit/eXecute Inhibit patch needs TLBR and
ROTR support in uasm. We also add a UASM_i_ROTR macro.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/953/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
64-bit CPUs have 64-bit c0_entrylo{0,1} registers. We should use the
64-bit dmtc0 instruction to set them. This becomes important if we
want to set the RI and XI bits present in some processors.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/954/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The function is #if 0ed out. There are no other occurrences of its
name in the tree. It is safe to remove.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/936/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The function probe_tlb() only does anything for processors that are
not PRID_COMP_LEGACY. This is precisely the set of processors for
which decode_configs() is called to do identical tlbsize probing
calculations. Therefore probe_tlb() is completely redundant and may
be removed.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/865/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
For 64-bit kernels with 64KB pages and two level page tables, there are
42 bits worth of virtual address space This is larger than the 40 bits of
virtual address space obtained with the default 4KB Page size and three
levels, so there are no draw backs for using two level tables with this
configuration.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/761/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
arch/mips/mm/highmem.c: In function 'kmap_init':
arch/mips/mm/highmem.c:130: error: 'init_mm' undeclared (first use in this function)
arch/mips/mm/highmem.c:130: error: (Each undeclared identifier is reported only once
arch/mips/mm/highmem.c:130: error: for each function it appears in.)
Signed-off-by: Yoichi Yuasa <yuasa@linux-mips.org>
Cc: linux-mips <linux-mips@linux-mips.org>
Patchwork: http://patchwork.linux-mips.org/patch/980/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
x86/mm is on 32-rc4 and missing the spinlock namespace changes which
are needed for further commits into this topic.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
cpu_cache_init and the things it calls should all be __cpuinit instead
of __devinit.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/938/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
It's based on walk_system_ram_range(), for archs that don't have
their own page_is_ram().
The static verions in MIPS and SCORE are also made global.
v4: prefer plain 1 instead of PAGE_IS_RAM (H. Peter Anvin)
v3: add comment (KAMEZAWA Hiroyuki)
"AFAIK, this "System RAM" information has been used for kdump to
grab valid memory area and seems good for the kernel itself."
v2: add PAGE_IS_RAM macro (Américo Wang)
Cc: Chen Liqin <liqin.chen@sunplusct.com>
Cc: Lennox Wu <lennox.wu@gmail.com>
Cc: Américo Wang <xiyou.wangcong@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: Yinghai Lu <yinghai@kernel.org>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Reviewed-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
LKML-Reference: <20100122081619.GA6431@localhost>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Makes it consistent with the extern declaration, used when CONFIG_HIGHMEM
is set Removes redundant casts in printout messages
Signed-off-by: Andreas Fenkart <andreas.fenkart@streamunlimited.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Chen Liqin <liqin.chen@sunplusct.com>
Cc: Lennox Wu <lennox.wu@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Processors that support the mips64r2 ISA can in four instructions
convert a shifted PGD pointer stored in the upper bits of c0_context
into a usable pointer. By doing this we save a memory load and
associated potential cache miss in the TLB exception handlers.
Since the upper bits of c0_context were holding the CPU number, we
move this to the upper bits of c0_xcontext which doesn't have enough
bits to hold the PGD pointer, but has plenty for the CPU number.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
While Linux provided an O_SYNC flag basically since day 1, it took until
Linux 2.4.0-test12pre2 to actually get it implemented for filesystems,
since that day we had generic_osync_around with only minor changes and the
great "For now, when the user asks for O_SYNC, we'll actually give
O_DSYNC" comment. This patch intends to actually give us real O_SYNC
semantics in addition to the O_DSYNC semantics. After Jan's O_SYNC
patches which are required before this patch it's actually surprisingly
simple, we just need to figure out when to set the datasync flag to
vfs_fsync_range and when not.
This patch renames the existing O_SYNC flag to O_DSYNC while keeping it's
numerical value to keep binary compatibility, and adds a new real O_SYNC
flag. To guarantee backwards compatiblity it is defined as expanding to
both the O_DSYNC and the new additional binary flag (__O_SYNC) to make
sure we are backwards-compatible when compiled against the new headers.
This also means that all places that don't care about the differences can
just check O_DSYNC and get the right behaviour for O_SYNC, too - only
places that actuall care need to check __O_SYNC in addition. Drivers and
network filesystems have been updated in a fail safe way to always do the
full sync magic if O_DSYNC is set. The few places setting O_SYNC for
lower layers are kept that way for now to stay failsafe.
We enforce that O_DSYNC is set when __O_SYNC is set early in the open path
to make sure we always get these sane options.
Note that parisc really screwed up their headers as they already define a
O_DSYNC that has always been a no-op. We try to repair it by using it for
the new O_DSYNC and redefinining O_SYNC to send both the traditional
O_SYNC numerical value _and_ the O_DSYNC one.
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Grant Grundler <grundler@parisc-linux.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Andreas Dilger <adilger@sun.com>
Acked-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Acked-by: Kyle McMartin <kyle@mcmartin.ca>
Acked-by: Ulrich Drepper <drepper@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jan Kara <jack@suse.cz>
The ohci-sm501 driver requires dma_declare_coherent_memory(). It is used
by the driver's local memory allocation with dma_alloc_coherent().
Tested on TANBAC TB0287(VR4131 + SM501).
[Ralf: Fixed reject in dma-default.c and removed the entire #if 0'ed block
in dma-mapping.h instead of just the #if 0.]
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
On an SMP system with cache aliases, the following sequence of events may
happen:
1) copy_user_highpage() runs on CPU0, invoking kmap_coherent() to create a
temporary mapping in the fixmap region
2) copy_page() starts on CPU0
3) CPU1 sends CPU0 an IPI asking CPU0 to run local_r4k_flush_cache_page()
4) CPU0 takes the interrupt, interrupting copy_page()
5) local_r4k_flush_cache_page() on CPU0 calls kmap_coherent() again
6) The second invocation of kmap_coherent() on CPU0 tries to use the
same fixmap virtual address that was being used by copy_user_highpage()
7) CPU0 throws a machine check exception for the TLB address conflict
Fixed by creating an extra set of fixmap entries for use in interrupt
handlers. This prevents fixmap VA conflicts between copy_user_highpage()
running in user context, and local_r4k_flush_cache_page() invoked from an
SMP IPI.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Makes code futureproof against the impending change to mm->cpu_vm_mask.
It's also a chance to use the new cpumask_ ops which take a pointer
(the older ones are deprecated, but there's no hurry for arch code).
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
For /proc/kcore, each arch registers its memory range by kclist_add().
In usual,
- range of physical memory
- range of vmalloc area
- text, etc...
are registered but "range of physical memory" has some troubles. It
doesn't updated at memory hotplug and it tend to include unnecessary
memory holes. Now, /proc/iomem (kernel/resource.c) includes required
physical memory range information and it's properly updated at memory
hotplug. Then, it's good to avoid using its own code(duplicating
information) and to rebuild kclist for physical memory based on
/proc/iomem.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: WANG Cong <xiyou.wangcong@gmail.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
For /proc/kcore, vmalloc areas are registered per arch. But, all of them
registers same range of [VMALLOC_START...VMALLOC_END) This patch unifies
them. By this. archs which have no kclist_add() hooks can see vmalloc
area correctly.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: WANG Cong <xiyou.wangcong@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Presently, kclist_add() only eats start address and size as its arguments.
Considering to make kclist dynamically reconfigulable, it's necessary to
know which kclists are for System RAM and which are not.
This patch add kclist types as
KCORE_RAM
KCORE_VMALLOC
KCORE_TEXT
KCORE_OTHER
This "type" is used in a patch following this for detecting KCORE_RAM.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: WANG Cong <xiyou.wangcong@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 9617729941 ("Drop free_pages()")
modified nr_free_pages() to return 'unsigned long' instead of 'unsigned
int'. This made the casts to 'unsigned long' in most callers superfluous,
so remove them.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Reviewed-by: Christoph Lameter <cl@linux-foundation.org>
Acked-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Kyle McMartin <kyle@mcmartin.ca>
Acked-by: WANG Cong <xiyou.wangcong@gmail.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: David Howells <dhowells@redhat.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Chris Zankel <zankel@tensilica.com>
Cc: Michal Simek <monstr@monstr.eu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Todo: Nothing ever detects CPU_BCM6338 but the code tests for it anyway.
Signed-off-by: Maxime Bizon <mbizon@freebox.fr>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The code after the vmalloc_fault: label in do_page_fault() modifies
user page tables, this is not correct for 64-bit kernels.
For 64-bit kernels we should go straight to the no_context handler
skipping vmalloc_fault.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
By combining swapper_pg_dir and module_pg_dir, several if conditions
can be eliminated from the tlb exception handler. The reason they
can be combined is that, the effective virtual address of vmalloc
returned is at the bottom, and of module_alloc returned is at the
top. It also fixes the bug in vmalloc(), which happens when its
return address is not covered by the first pgd.
Signed-off-by: Wu Fei <at.wufei@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Fix the pagefault oom path which does not drop mm->mmap_sem.
This was introduced by commit c7c1e3846b
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
They tend to get not updated when files are moved around or copied and
lack any obvious use. While at it zap some only too obvious comments and
as per Shinya's suggestion, add a copyright header to extable.c.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Acked-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
* Remove smp_lock.h from files which don't need it (including some headers!)
* Add smp_lock.h to files which do need it
* Make smp_lock.h include conditional in hardirq.h
It's needed only for one kernel_locked() usage which is under CONFIG_PREEMPT
This will make hardirq.h inclusion cheaper for every PREEMPT=n config
(which includes allmodconfig/allyesconfig, BTW)
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some of the were relying into smp.h being dragged in by another header
which of course is fragile. <asm/cpu-info.h> uses smp_processor_id()
only in macros and including smp.h there leads to an include loop, so
don't change cpu-info.h.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This allows the callers to now pass down the full set of FAULT_FLAG_xyz
flags to handle_mm_fault(). All callers have been (mechanically)
converted to the new calling convention, there's almost certainly room
for architectures to clean up their code and then add FAULT_FLAG_RETRY
when that support is added.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The TLB handlers need to check for huge pages and give them special
handling. Huge pages consist of two contiguous sub-pages of physical
memory.
* Loading entrylo0 and entrylo1 need to be handled specially.
* The page mask must be set for huge pages and then restored after
writing the TLB entries.
* The PTE for huge pages resides in the PMD, we halt traversal of the
tables there.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The l parameter to iPTE_LW() is unused. Remove it and from some of its
callers as well.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
CPU_CAVIUM_OCTEON is mips_r2 which is handled before the switch. This
label in the switch statement is dead code, so we remove it.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Reviewed by: David VomLehn <dvomlehn@cisco.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Some CPUs do not need ehb instructions after writing CP0 registers.
By allowing ehb generation to be overridden in
cpu-feature-overrides.h, we can save a few instructions in the TLB
handler hot paths.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Try to fold the 64-bit TLB refill handler opportunistically at the
beginning of the vmalloc path so as to avoid splitting execution flow in
half and wasting cycles for a branch required at that point then. Resort
to doing the split if either of the newly created parts would not fit into
its designated slot.
Original-patch-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The logic used to split the r4000 refill handler is liberally
sprinkled with magic numbers. We attempt to explain what they are and
normalize them against a new symbolic value (MIPS64_REFILL_INSNS).
CC: David VomLehn <dvomlehn@cisco.com>
Reviewed-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The address range size calculation inside local_flush_tlb_kernel_range()
is being truncated by a too small size variable holder on 64-bit systems.
The truncated size can result in an erroneous tlbsize check that means we
sit spinning inside a loop trying to flush a hige number of TLB entries.
This is for all intents and purposes a system hang. Fix by using an
appropriately sized valiable to hold the size.
[Ralf: Greg's original patch submission identified the issue and fixed one
instance in tlb-r4k.c but there there were several more. For consistency
I also modified tlb-r3k.c even though that file is only used on 32-bit.]
Signed-off-by: Greg Ungerer <gerg@snapgear.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Commit 351336929c (kernel.org) rsp.
b3594a089f1c17ff919f8f78505c3f20e1f6f8ce (linux-mips.org):
> From: Chris Dearman <chris@mips.com>
> Date: Wed, 19 Sep 2007 00:58:24 +0100
> Subject: [PATCH] [MIPS] Allow setting of the cache attribute at run time.
>
> Slightly tacky, but there is a precedent in the sparc archirecture code.
introduces the variable _page_cachable_default, which defaults to zero and.
is used to create the prototype PTE for __kmap_atomic in
arch/mips/mm/init.c:kmap_init before initialization in
arch/mips/mm/c-r4k.c:coherency_setup, so the default value of 0 will be
used as the CCA of kmap atomic pages which on many processors is not a
defined CCA value and may result in writes to kmap_atomic pages getting
corrupted. Debugged by Jon Fraser (jfraser@broadcom.com).
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Synchronize dma_map_page/dma_unmap_page and dma_map_single/dma_unmap_single.
This will reduce unnecessary writebacks and invalidates.
[Ralf: make dma_unmap_page an inline function.]
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The file arch/mips/mm/sc-rm7k.c needlessly defines two global symbols:
rm7k_sc_ops
rm7k_tcache_enabled
This patch makes these symbols static.
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@movial.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Use debug_kmap_atomic in kmap_atomic, kmap_atomic_pfn, and
iomap_atomic_prot_pfn.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The Alchemy manuals state:
"All pipeline hazards and dependencies are enforced by hardware interlocks
so that any sequence of instructions is guaranteed to execute correctly.
Therefore, it is not necessary to pad legacy MIPS hazards (such as
load delay slots and coprocessor accesses) with NOPs."
Run-tested on Au12x0, without any ill effects.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch removes the various CPU_AU1??? model constants in favor of
a single CPU_ALCHEMY one.
All currently existing Alchemy models are identical in terms of cpu
core and cache size/organization. The parts of the mips kernel which
need to know the exact CPU revision extract it from the c0_prid register
already; and finally nothing else in-tree depends on those any more.
Should a new variant with slightly different "company options" and/or
"processor revision" bits in c0_prid appear, it will be supported
immediately (minus an exact model string in cpuinfo).
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
dma_cache_wback_inv() expects virtual address, but physical was provided
due to translation via plat_dma_addr_to_phys().
If replaced with dma_addr_to_virt(), page fault oops from dma_unmap_page()
is gone on au1550 platform.
Signed-off-by: Jan Nikitenko <jan.nikitenko@gmail.com>
Acked-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Current VR5500 processor support lacks of some functions which are
expected to be configured/synthesized on arch initialization.
Here're some VR5500A spec notes:
* All execution hazards are handled in hardware.
* Once VR5500A stops the operation of the pipeline by WAIT instruction,
it could return from the standby mode only when either a reset, NMI
request, or all enabled interrupts is/are detected. In other words,
if interrupts are disabled by Status.IE=0, it keeps in standby mode
even when interrupts are internally asserted.
Notes on WAIT: The operation of the processor is undefined if WAIT
insn is in the branch delay slot. The operation is also undefined
if WAIT insn is executed when Status.EXL and Status.ERL are set to 1.
* VR5500A core only implements the Load prefetch.
With these changes, it boots fine.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Thanks to David Daney helping with debugging and testing.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
We add a dev parameter to plat_unmap_dma_mem(), and hooks for
plat_dma_supported() and plat_extra_sync_for_device() which should be
nop changes for all existing targets.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Expand the case statement for build_tlb_write_entry so that it does
the right thing on Cavium CPU variants.
Signed-off-by: Tomaso Paoletti <tpaoletti@caviumnetworks.com>
Signed-off-by: Paul Gortmaker <Paul.Gortmaker@windriver.com>
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Take all the OCTEON specific files that were added, and hook them into
the build system for the arch/mips. For versions of GCC that lack
OCTEON support, override gas target architecture.
Signed-off-by: Tomaso Paoletti <tpaoletti@caviumnetworks.com>
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Follow precedent of other boards, and hook-up the CPU specific cache
init.
Signed-off-by: Tomaso Paoletti <tpaoletti@caviumnetworks.com>
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
dma_free_noncoherent() and dma_free_coherent() are missing calls to
plat_unmap_dma_mem(). This patch adds them.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The indy_sc_ops variable in arch/mips/mm/sc-ip22.c is needlessly defined
global, and this patch makes it static.
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@movial.fi>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
---
We already have sufficient infrastructure to support VR5500 and VR5500A
series processors. Here's a Makefile support to make it selectable by
ports, and enable it for NEC EMMA2RH Markeins board.
This patch also fixes a confused target help, and adds 1Gb PageMask bits
supported by VR5500 and its variants.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
We were getting away with this for so long only because the only platform
with a non-empty plat_unmap_dma_mem() doesn't call dma_sync_sg_for_cpu()
and dma_sync_sg_for_device() from its commonly used drivers.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
trap_init issues flush_icache_range(), which uses ipi functions to
get icache flushing done on all cpus. But this is done before interrupts
are enabled and caused WARN_ON messages. This changeset introduces
a new local_flush_icache_range() and uses it before interrupts (and
additional CPUs) are enabled to avoid this problem.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Bug originally found and reported by Julia Lawall <julia@diku.dk>. I
decieded that the whole error check was mostly useless paranoia and should
be discarded. It would only ever trigger if r3k_have_wired_reg has a wrong
value.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Remove arch-specific show_mem() in favor of the generic version.
This also removes the following redundant information display:
- pages in swapcache, printed by show_swap_cache_info()
where show_mem() calls show_free_areas(), which calls
show_swap_cache_info().
And show_mem() does now actually print something on configurations
with multiple nodes.
Signed-off-by: Johannes Weiner <hannes@saeurebad.de>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add per-device dma_mapping_ops support for CONFIG_X86_64 as POWER
architecture does:
This enables us to cleanly fix the Calgary IOMMU issue that some devices
are not behind the IOMMU (http://lkml.org/lkml/2008/5/8/423).
I think that per-device dma_mapping_ops support would be also helpful for
KVM people to support PCI passthrough but Andi thinks that this makes it
difficult to support the PCI passthrough (see the above thread). So I
CC'ed this to KVM camp. Comments are appreciated.
A pointer to dma_mapping_ops to struct dev_archdata is added. If the
pointer is non NULL, DMA operations in asm/dma-mapping.h use it. If it's
NULL, the system-wide dma_ops pointer is used as before.
If it's useful for KVM people, I plan to implement a mechanism to register
a hook called when a new pci (or dma capable) device is created (it works
with hot plugging). It enables IOMMUs to set up an appropriate
dma_mapping_ops per device.
The major obstacle is that dma_mapping_error doesn't take a pointer to the
device unlike other DMA operations. So x86 can't have dma_mapping_ops per
device. Note all the POWER IOMMUs use the same dma_mapping_error function
so this is not a problem for POWER but x86 IOMMUs use different
dma_mapping_error functions.
The first patch adds the device argument to dma_mapping_error. The patch
is trivial but large since it touches lots of drivers and dma-mapping.h in
all the architecture.
This patch:
dma_mapping_error() doesn't take a pointer to the device unlike other DMA
operations. So we can't have dma_mapping_ops per device.
Note that POWER already has dma_mapping_ops per device but all the POWER
IOMMUs use the same dma_mapping_error function. x86 IOMMUs use device
argument.
[akpm@linux-foundation.org: fix sge]
[akpm@linux-foundation.org: fix svc_rdma]
[akpm@linux-foundation.org: build fix]
[akpm@linux-foundation.org: fix bnx2x]
[akpm@linux-foundation.org: fix s2io]
[akpm@linux-foundation.org: fix pasemi_mac]
[akpm@linux-foundation.org: fix sdhci]
[akpm@linux-foundation.org: build fix]
[akpm@linux-foundation.org: fix sparc]
[akpm@linux-foundation.org: fix ibmvscsi]
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Muli Ben-Yehuda <muli@il.ibm.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Avi Kivity <avi@qumranet.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus: (54 commits)
[MIPS] Remove mips_machtype for LASAT machines
[MIPS] Remove mips_machtype from EMMA2RH machines
[MIPS] Remove mips_machtype from ARC based machines
[MIPS] MTX-1 flash partition setup move to platform devices registration
[MIPS] TXx9: cleanup and fix some sparse warnings
[MIPS] TXx9: rename asm-mips/mach-jmr3927 to asm-mips/mach-tx39xx
[MIPS] remove machtype for group Toshiba
[MIPS] separate rbtx4927_time_init() and rbtx4937_time_init()
[MIPS] separate rbtx4927_arch_init() and rbtx4937_arch_init()
[MIPS] txx9_cpu_clock setup move to rbtx4927_time_init()
[MIPS] txx9_board_vec set directly without mips_machtype
[MIPS] IP22: Add platform device for Indy volume buttons
[MIPS] cmbvr4133: Remove support
[MIPS] remove wrppmc_machine_power_off()
[MIPS] replace inline assembler to cpu_wait()
[MIPS] IP22/28: Add platform devices for HAL2
[MIPS] TXx9: Update and merge defconfigs
[MIPS] TXx9: Make single kernel can support multiple boards
[MIPS] TXx9: Update defconfigs
[MIPS] TXx9: Reorganize PCI code
...
The following routines
uasm_rel_highest()
uasm_rel_higher()
are needlessly defined global. This patch makes them static.
Compile-tested using a customized config for the Malta board. Booting
the same board up to the shell prompt was also successful with this
patch applied.
Spotted by sparse.
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@movial.fi>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The generated copy_page for R4k CPU with a 128 byte cache line size used
Create Dirty Exclusive cache line operations even if only part of the
cache line was filled. This change avoids generating cache operations,
if only part of the cache line size is copied in one loop. It also
increases the maxmimum loop size, because the generated code even fits
into the available space for r4k CPUs with 128 byte cache line size.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Resolve these mismatches by defining affected functions with the __cpuinit
attribute, rather than __init.
Signed-off-by: Shane McDonald <mcdonald.shane@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
It's never used and the comments refer to nonatomic and retry
interchangably. So get rid of it.
Acked-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Assuming the call of kmap_coherent in local_r4k_flush_cache_page doesn't
need fixing this was skipped in fcae549295bcae801ac48fc1c2030ab8cc487020.
Turns out it needed the same change after all.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Treat R4700 like R4600 in build_tlb_probe_entry. Without this fix kernel
will lock up.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch removes the no longer used export of __kmap_atomic_to_page.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
No users for the copy_from_user_page() routine exist outside of the
core kernel code. Therefore, EXPORT_SYMBOL(copy_from_user_page) is
useless, and this patch removes it.
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The copy_to_user_page() function is called only in the core kernel
code. Therefore, there is no need to export it. This patch removes
EXPORT_SYMBOL(copy_to_user_page).
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The copy_user_highpage() routine has no users outside of the
core kernel code, so exporting this symbol is pointless.
This patch removes EXPORT_SYMBOL(copy_user_highpage).
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Slightly tacky, but there is a precedent in the sparc archirecture code.
Signed-off-by: Chris Dearman <chris@mips.com>
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Fold the SB-1 specific implementation of clear_page/copy_page in the
generic version, and rewrite that one in tlbex style. The immediate
benefits:
- It converts the compile-time workaround for SB-1 pass 1 prefetches
to a more efficient run-time check.
- It allows adjustment of loop unfolling, which helps to reduce the
number of redundant cdex cache ops.
- It fixes some esoteric cornercases (the cache line length calculations
can go wrong, and support for 64k pages without prefetch instructions
will overflow the addiu immediate).
- Somewhat better guesses of "good" prefetch values.
Signed-off-by: Thiemo Seufer <ths@networkno.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
flush_cache_vmap / flush_cache_vunmap were calling flush_cache_all which -
having been deprecated - turned into a nop ...
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Linus Torvalds