The identification of the hardware section in the NVM
of new devices has been changed, hence the need to add it
to iwl_cfg and adapt the code that uses this value
accordingly.
Signed-off-by: Eran Harary <eran.harary@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Newer firmware will support uAPSD clients in AP/GO mode, so complete
the driver support for it. The way it works is described in comments
in the code, but basically the driver just has to pass down all the
mac80211 requests and do accounting on agg/non-agg queues properly.
For older firmware, this doesn't change anything as it ignores the
fields used by the new firmware, and we only advertise uAPSD support
when the firmware does.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The driver wasn't reading the NVM properly. While this
didn't lead to any issue until now, it seems that there
is an old version of the NVM in the wild.
In this version, the A band channels appear to be valid
but the SKU capabilities (another field of the NVM) says
that A band isn't supported at all.
With this specific version of the NVM, the driver would
think that A band is supported while the HW / firmware
don't. This leads to asserts.
Cc: <stable@vger.kernel.org> [3.10+]
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Not doing so will let BT kill our probe requests leading to
failures in scan.
Cc: <stable@vger.kernel.org> [3.10+]
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
We had a bug that prevented us from removing a station
after we entered the drain flow:
We assign sta to be NULL if it was an error value.
Then we tested it against -EBUSY, but forget to retrieve
the value again from mvm->fw_id_to_mac_id[sta_id].
Due to this bug, we ended up never removing the STA from
the firmware. This led to an firmware assert when we remove
the GO vif.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Configure scheduled scan to notify match found on every beacon
or probe response if the scan request doesn't contain valid ssid
list for filtering.
Without this configuration the FW passes all beacons to the host
but doesn't notify the stack that the scan results are ready for
processing.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Reviewed-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This can be useful to be able to spot the firmware version
from the error reports without needing to fetch it from
another place.
Cc: <stable@vger.kernel.org> [3.10+]
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The iwlwifi scheduled scan implementation doesn't adhere to the
userspace API correctly - the API assumes that any new incoming
'incompatible' request (like scan or remain-on-channel for this
driver) will just cancel the scheduled scan. Instead our driver
relies on userspace cancelling it, thus breaking existing wpa_s
versions.
Cc: stable@vger.kernel.org [3.13]
Fixes: 35a000b7c1 ("iwlwifi: mvm: support sched scan if supported by the fw")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The address pointer used in the function shouldn't be static
since it's local data only. Having it static causes races if
a single machine has two devices, as the pointer would be
shared between instances.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
None of the devices supported by iwldvm have support for
shadow registers. This means that we wake the NIC
when we increment the write pointer on Tx ring.
This happened even before my bad commit mentionned below.
Since my commit below, we wake up the NIC when we put a
host command on the ring regardless of shadow register
support. This means that in iwldvm (when the NIC doesn't
support shadow register), we wake up the NIC twice:
pcie_enqueue_hcmd:
wake up the NIC
iwl_pcie_txq_inc_wr_ptr:
wake up the NIC - no shadow reg support
Since waking up the NIC means that we need to acquire a
spinlock, this obviously leads to a recursive spinlock
and hence a freeze.
Fixes: b943949105 ("iwlwifi: pcie: keep the NIC awake when commands are in flight")
Reported-by: Janusz Dziedzic <janusz.dziedzic@gmail.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Keeping this as 0 is ok according to spec section 9.7.11
as this means the limits are according to the Tx/Rx
supported MCS x NSS bitmap. Initially we've set these as
there were concerns of interop issues but these turned out
to be false.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
If we try to write NVM that do not exist, the function will return
uninitialized value. fixed.
Signed-off-by: Eytan Lifshitz <eytan.lifshitz@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Add an inline helper function for getting an RX packet's
length or payload length and use it throughout the code
(most of which I did using an spatch.)
While at it, adjust some code, and remove a bogus comment
from the dvm calibration code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Eran Harary <eran.harary@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
All beamformee supporting chips have the ability to support
VHT NDP in up to 4 STSs. So change the published beamformee
STS cap accordingly to 3 as it should be Nsts-1.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The request of SMPS issued by the Thermal Throttling code
was not reset when we disassociated - fix that.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
It's a bit strange to treat an array as a pointer, so use proper
array indexing instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
If the length isn't set it means we want all the SRAM.
Also - this is perfectly valid to partially dump starting
at offset 0.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Discovered by klocwork
Array 'iwl_rate_mcs' of size 15 may use index value(s) -1
* rs.c:2562: index = iwl_hwrate_to_plcp_idx(rate)
* rs.c:2562: Result of function call 'iwl_hwrate_to_plcp_idx(rate)' is '[-1,14]'
* rs.c:2565: Array 'iwl_rate_mcs' size is 15.
* rs.c:2565: Possible attempt to access element -1 of array 'iwl_rate_mcs'.
While at it stop using index = -1 and always use IWL_RATE_INVALID
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Some NIC comes with more than the 4 NVM (non volative
memory) sections described in the nvm_to_read array.
These NICs usually get their NVM from an external file
fetched from userland during init.
We already parsed the file, but sent to the NIC only 4 NVM
sections whereas there could be more sections in the file.
Fix this.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Since seq_number is incremented right after using
it, so printed seq_ctrl was actually the next
one to be used.
Fix it by incrementing the seq_number only later,
before saving it.
Additionally, use the IEEE80211_SEQ_TO_SN macro
in order to print the actual sequence number.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Enabling the oscillator consumes slightly more power (100uA)
but allows to make sure that we exit from L1 on time.
Not doing so might lead to a PCIe specification violation
since we might wake up from L1 at the wrong time.
This issue has been identified on 3160 and 7260 only.
On older NICs L1 off is not enabled, on newer NICs (7265),
the issue is fixed.
When the bug occurs the user sees that the NIC has
disappeared from the PCI bridge, any access to the device
returns 0xff.
This fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=64541
and has been extensively discussed here:
http://markmail.org/thread/mfmpzqt3r333n4bo
Cc: stable@vger.kernel.org [3.10+]
Fixes: 99cd471423 ("iwlwifi: add 7000 series device configuration")
Reported-and-tested-by: wzyboy <wzyboy@wzyboy.org>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When we disassociate in managed mode, we flush the queues
after mac80211 has already removed the station.
During that time, the pointer to ieee80211_sta to the
fw_id_to_mac_id map is -EINVAL. In that case we should not
set the station as being drained when the last Tx of this
station has exited the shared Tx queue since we are
flushing all the queues anyway.
The draining logic is meant to be used in GO / AP mode only.
In GO / AP mode, we set -EBUSY in the fw_id_to_mac_id map.
This is why testing the ieee80211_sta pointer in the
fw_id_to_mac_id map with IS_ERR isn't enough to set the
station as draining, we need to check that it is -EBUSY.
The only impact of the bug was a print:
Drained sta 1, but it is internal?
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
If we can't switch to a column because no rates are supported
in that column this led to a state where the search cycle
got stuck and never ended. This in turn also led to aggregation
not being turned on. Fix this by marking a column as
visited if we can't switch to it.
Reported-and-tested-by: Karl Beldan <karl.beldan@gmail.com>
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Cleanup of iwl_mvm_leds was missing in case of error,
resulting in the following warning:
WARNING: at lib/kobject.c:196 kobject_add_internal+0x1f4/0x210()
kobject_add_internal failed for phy0-led with -EEXIST, don't try to register things with the same name in the same directory.
which prevents further reloads of the driver.
Cc: stable@vger.kernel.org [3.10+]
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The power settings need to be updated after a binding flow is done
and before quota calculations. This was missing in the start_ap_ibss()
flow. Fix it.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The state variable was not set to false in case of a failure to
complete the start_ap_ibss() flow.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Acked-by: Christian Lamparter <chunkeey@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Found by klocwork analysis.
mvm could be NULL which may cause a NULL dereference
in a theoretical call flow
rs_fill_lq_cmd(mvm = NULL, ...)
rs_build_rates_table
rs_fill_rates_for_column
ucode_rate_from_rs_rate
IWL_ERR(mvm,...)
No real reason for passing NULL to rs_fill_lq_cmd so fix that.
Reported-by: Eytan Lifshitz <eytan.lifshitz@intel.com>
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Currently, the MAC context tsf_id assignment and the master/slave
relations are determined only when a new vif is added, as part
of the MAC context resource allocation. However, at this stage, the
beacon interval is not known, and thus could not be taken into account
in the master-slave algorithm.
To fix this, recalculate the MAC context tsf_id assignment,
just before the MAC context is activated, i.e., just before
a station VMAC is configured to associated and before an AP
VMAC is started.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Change the parameters for calculating an AP TBTT to 64/36 instead of
80/20, to increase the interval between a station vif and an AP
vif TBTT events.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The access to the CSR_RESET reg should be done as a complete
DWORD and not by setting a bit. This is the right way to reset
the device.
Signed-off-by: Eran Harary <eran.harary@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Instead of always calling ieee80211_beacon_loss() on every missed
beacons notification, call this function only if the number of
consecutive missed beacons from last rx is higher than a predefined
threshold.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
If the channel min-width changes, we can update the PHY ctx, even if
it has multiple references.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Reviewed-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This allows to format it at will using external tools.
Since different teams want it in different formats, dump
the raw data and everyone can play with the data the way
they want.
While at it - make this code slightly more robust by making
the required verification on the offsets / length in the
write handler.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Don't check if mvm->fw->cs is NULL since it can't be.
cs is an array member of iwl_fw, it can't be NULL.
Use memset(ptr, 0, sizeof(*ptr)); instead of
memset(ptr, 0, sizeof(struct ptr_type));
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The firmware needs to be stopped quickly (100ms) after the
RFKILL interrupt fired. Failing to do so would allow the
firmware to access the radio registers which would lead to
a hardware error.
Before this change, we would kill the firmware only when
mac80211 stops the device which can take a fair amount of
time. Take a shortcut by stopping the device right away
in the interrupt.
This is not relevant if the current firmware is INIT
firmware since that firmware can run while in RFKILL.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Calling stop_device when start_fw wasn't called would issue:
Stopping tx queues that aren't allocated...
Also allow the op_mode to call stop_device and then to
disable the Tx queues - in that case just silently ignore
the disabling on the Tx queues, since the PRPH registers
aren't reachable any more.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This is useless and introduces a dependency between rfkill
and stop_device - the op_mode can't call stop_device from
the rfkill notification since it would lead to an endless
recursion.
Next patches will need to do so.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Under very specific circumstances, the firmware might
ignore a host command. This was debugged and we ended up
seeing that the power management hardware was faulty.
In order to workaround this issue, we keep the NIC awake
as long as we have host commands in flight. This will avoid
to put the hardware into buggy condition.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
In case of invalid section_id, the function returns after
it aleready allocated memory. Fixed by change the order of actions.
Signed-off-by: Eytan Lifshitz <eytan.lifshitz@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The AC / fifo mapping was wrong - BE packets landed in VO
FIFO. The iwl_mvm_tx_fifo enumeration isn't in the same
order as ieee80211_ac_numbers enumeration.
Since the firmware relies on fifo / ac mapping - this led
to wrong behavior. E.g. the firmware sends beacon with the
same QoS parameters as VO, and it actually took the
parameters of BK. There are probably more severe issues.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Add new device / subdevice ID for 7265 series.
Fix 2 mistakes on the way.
Signed-off-by: Oren Givon <oren.givon@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This lock was never acquired in the primary interrupt
handler, but since it was acquired along with irq_lock
which had to disable interrupts, rxq->lock had to disable
interrupts too.
Now that trans_pcie->irq_lock isn't acquired in the primary
interrupt handler, rxq->lock can let interrupt enabled.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Since we don't take this lock in the primary interrupt
handler, there is no pointin disabling the interrupt
in the critical section protected by trans_pcie->irq_lock.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Handling interrupt with no cause and printing logs doesn't
need to be ICT / non-ICT specific move this to the common
code.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This was useful when the handling was not in the same
context as the interrupt cause retrieval: we could have
several hard interrupts until the handler gets called.
Since we retrieve the interrupt cause in the handler itself,
there is no need to OR the interrupt causes.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
These functions are meant to return an interrupt cause and
not an irqreturn_t.
We still return IRQ_HANDLED if we had an error and IRQ_NONE
if our device hasn't fired any interrupt.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Instead of having:
iwl_pcie_irq_handler
iwl_pcie_isr_ict
iwl_pcie_isr_non_ict
we now have:
iwl_pcie_irq_handler:
if (use_ict))
iwl_pcie_int_cause_ict;
else
iwl_pcie_int_cause_non_ict;
This is much clearer.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
We now disable the interrupts in the hardware from the
upper half and all the rest (including reading the interrupt
cause) is done in the handler.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The purpose of this is to be able to call these functions
from the interrupt handler and not from the primary
interrupt handler.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Separate the code that simply disables interrupt in the
hardware and the code that checks what interrupt fired.
This will be useful to move the second part in the threaded
handler which will be done in a future patch.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Track the interrupt mask in software, making it exactly
what is configured in the interrupt mask register in the
hardware.
This allows not to access the register from the interrupt
handler. This was the case for ICT interrupt already, but
not for non-ICT interrupt.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Since iwl_trans_pcie_alloc_ict is called in the PCIe
allocation code, we always set CSR_INT_BIT_RX_PERIODIC.
Move that bit to the default list of interrupts we enable
and simplify the code.
Also use dma_zalloc_ and avoid to memset the memory
afterwards.
trans_pcie->ict_index is 0 since trans_pcie has just been
kzalloced, remove the redundant assignment.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
RTS protection was turned on once aggregation was enabled but it
was never turned off. Remove turning on RTS protection in the LQ command
completely as TX_CMD_FLG_PROT_REQUIRE gets set in iwl_mvm_set_tx_cmd
for every Tx which is part of an aggregation. This would already cause
RTS protection to be used during aggregations.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Set the Tx/Rx highest long GI rates in the VHT Supported MCS Set
field according to the chip capabilties.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
MCS9 introduces some corner cases in the current rs
algorithm which may lead to non optimal throughput and
instability in the throughput. Until all the corner
cases are resolved disable MCS9 for Tx as a workaround
which yields better throughput results as MCS8 is much
more stable.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Extract the scale action decision to a different function
in preparation of modifying it. While at it also convert
the scale action values from hardcoded values to a clear enum.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The logs are emitted in a flow in which there were retries
and the rates in the rate table entry didn't match the active
or search table. This doesn't indicate a problem and is
expected in most cases where there will be retries for some
reason. Remove the logs.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The new logic will attempt more rates with less retries
per rate. Also when starting off with MIMO it will
fallback to SISO with the same MCS and only then to Legacy.
Previously we fell back directly to Legacy.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The supported legacy rate mask is initialized when rs
is initialized based on the remote peer supported rates.
There's no need to re mask it repeatedly with the supported
remote peer rates.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Simplify the code a bit more by extracting the rates table
building logic into a separate function and handle setting
a fixed rate for debug in a separate flow.
Also avoid using and saving ucode rate format in different
places. Instead use rs_rate struct and convert to ucode format
only when filling the rates table in the LQ command.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Current firmware doesn't handle well uAPSD in P2P Client.
When it will be fixed, the firmware will set a TLV flag to notify
the driver that uAPSD is supported in P2P client mode.
Check this flag when sending power command for P2P client.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
It is not currently implemented for SDIO, and not required for other slave
buses as well.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Clear the FW_ERROR status before the common start_fw transport code.
Remove the transport specific clears.
After these patches the FW_ERROR flag is only set and cleared by common
transport code.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
In case a sync command timeouts or Tx is stuck while a FW error
interrupt arrives, we might call iwl_op_mode_nic_error twice before
a restart has been initiated. This will cause a reprobe. Unify calls
to this function at the transport level and only call it on the first
FW error in a given by checking the transport FW error flag.
While at it, remove the privately defined iwl_nic_error from PCIE code
and use the common callback instead.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Move rs_program_fix_rate right before it's caller where we're
already in the context of an ifdef CPTCFG_MAC80211_DEBUGFS so
we can get rid of the extra ifdefs surrounding the original
location.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Stop Tx and commands from arriving to the transport layer when a FW
error has occurred. A HW recovery should take place before. Remove
transport specific checks of the same nature (note that not all
transports were protected).
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The same bits are employed in all transport layers. Put the status
field in the common transport layer. This allows us to employ them
in common transport code.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The stop_hw trans callback is not well defined. It is missing in many
cleanup flows and the division of labor between stop_device/stop_hw
is cumbersome. Remove stop_hw and use stop_device to perform both.
Implement this for all current transports.
PCIE needs some extra configuration the op-mode is leaving to configure
RF kill. Expose this explicitly as a new op_mode_leave trans callback.
Take the call to stop_device outside iwl_run_mvm_init_ucode, this
makes more sense and WARN when we want to run the INIT firmware while
it has run already.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The documentation for smps_requests is unclear, rewrite it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Configure the phy context to the minimum required
bandwidth, given by ctx->min_def.
Tuning to a narrower bandwidth should reduce the
noise level and consume less power.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Configure the fw to filter multicast according to
the addresses given by mac80211.
Note that bssid should be given even if we want
to pass all the multicast frames.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This allows to tweak the power parameters per vif.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Enable power save on P2P client interface only if it is the
only bound interface.
Avoid using uAPSD if P2P client is associated to GO that uses
opportunistic power save. This is due to current FW limitation.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When monitor interface is activated device power save needs
to be disabled.
Re-consider power management status on other active
interfaces when monitor interface is bound or unbound.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
FW still does not support power management on multiple MAC interfaces.
Currently the driver enforce this limitation by disabling PM if second
interface is added. Change this behavior to allow PM on a single interface
even if other interfaces exist but not bound to any specific PHY.
PM will be enabled if only one single interface is bound.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
FW implements protective algorithm to identify AP's improper uAPSD
behavior. FW sends misbehaving AP notification in this case.
Add this notification handling. Avoid using uAPSD in next association
to the exactly same AP. Refactor iwl_mvm_power_build_cmd() to move
uAPSD related code to a separate function.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
If the device is MIMO and VHT capable it supports Tx STBC.
Unlike HT, any chip that supports VHT also support STBC so
no need for a config parameter.
Using num_of_ants multiple times warranted caching it.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
It was set to zero which reflects support of a single STS.
Set according to the number of Rx antennas which correctly
reflects the number of STSs the STA can receive in a VHT NDP.
This improves beamforming and has been tested to improve Rx
throughput.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Not all chips support STBC so allow this to be
another config parameter per chip type. If STBC
is supported then publish it in the HT caps.
Since 7260/7265/3160 chips support it - set the stbc
support bit.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This patch adds a cipher scheme support to extend a set of
the supported ciphers. The driver reads a cipher scheme list TLV
from FW image and passes it to mac80211 on hw registration.
After the cipher schemes are registered the driver handles key
installation and Tx/Rx calls related to the new ciphers.
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Send firmware a Smart FIFO Configuration host command to allow
interrupt coalescing. The smart FIFO is enabled when there is
only one bound interface (other than p2p devices which are
ignored) and it is of type station, and activated while the
station is associated.
Smart Fifo allows aggragations of DMA transactions and by that
causes processor and memory controller to stay for a longer time
on lower c-states, thus saving platform power.
Firmware relies on driver to activate and disable it.
Signed-off-by: Lilach Edelstein <lilach.edelstein@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
iwlmvm relies on the current mac80211 behaviour of allowing
station pointers to be valid for an RCU grace period after
returning from the sta_state() callback. To optimise these
cases, this behaviour is going away, so make the driver use
the new sta_pre_rcu_remove() method to clear the pointer in
the fw_id_to_mac_id[] array.
Since this may happen while the station is still present in
the firmware, don't set the pointer to NULL but to -ENOENT
to mark this particular case. In client mode, the station
is kept even longer (until marking the MAC as unassociated)
so the drain flow must take this new behavior into account.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Products that have only 1 antenna in Rx don't support MIMO
in RX. As a consequence, they will be in STATIC always.
Don't tell mac80211 to update SMPS in that case. mac80211
would send an action frame to the AP which is clearly
bogus.
As a matter of fact, we have seen that some APs send a
deauth when that happens.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Sync to SCO is a feature that allows to synchronise the
wifi activity with the predictable BT activity in
SCO profile. This allows to reduce the collisions and
improve overall quality.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Rewrite the search cycle state machine to use a more data
oriented approach where the different Tx columns (configs)
limitations and next columns to search are reprsented in
tables which are easy to change. This overhaul also includes
several major fixes:
1. Prevent going back to a specific Tx column in a search
cycle if it was already explored.
2. Avoid switching to a Tx column that doesn't have any chance
if it performs perfectly to beat the current throughput we're
getting.
These issues were degrading throughput as they were causing
switching to "bad" Tx columns.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Use the 20Mhz channel width define instead of just the number
zero for legacy rates. Note that the define has the same value
so this is just a minor cleanup.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The table rs_ht_to_legacy is used to get the next legacy rate
following the last HT or VHT rate in the LQ rates table.
The mapping wasn't correct as well as didn't include entries
for MCS8/9 which led to out of bounds access. This didn't
trigger a crash but led to legacy rate entries using 1Mbps
rate.
In 5Ghz this probably caused the Tx to fail completely given
that Tx attempt would have reached the legacy entries and 1Mbps
isn't valid.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Drop code which was relevant when there were chips with
3 antennas. Setting to ANT_AB should be ok with all mvm
supported chips.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Introduce rs_rate which represents a rate. Use this structure
instead of iwl_scale_tbl_info where we're dealing with a single
rate.
This avoids allocating the big iwl_scale_tbl_info structure
on the stack in several cases like converting to ucode rate
format or from ucode rate format.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Remain in the same Tx modulation (i.e. column) for a longer
time before starting a search cycle for a better modulation.
This has been shown to give better results.
Also change the name of the timeout define to better match its
description.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Expected TPT table was updated only when switching to a new
modulation. This is wrong as toggling aggregation changes
the expected TPT signficantly.
This leads to scenarios where turning aggregation on after
being in MIMO sends us back to SISO despite a perfect success
ratio.
This occurred because the TPT of the SISO mode was being
estimated based on aggregation while the MIMO one wasn't.
Also remove an error print which isn't an error anymore
since we might be updating the expected TPT table due
to aggregation changes.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This terminates a test window of a new rate quicker in case
we've hit a bad rate and should recover better.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Enable better tracking of different decisions made
by the rate scale algorithm.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Remote peer can publish a different number of supported nss via the
operating mode notification IE or action frame. If it limits to 1
then we don't want mimo rates configured in the rate table.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
MCS9 in NSS=1 or NSS=2 isn't valid for 20Mhz so don't enable
it in case we're dealing with a 20Mhz sta. Trying to configure an
MCS9 rate with 20Mhz in the LQ rate table would lead to a FW assert.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Switch to using the new btcoex decision api regarding MIMO and stop
accessing the internal btcoex structs.
In case MIMO should be disabled it would detect this upon the next
Tx and force a search. The search will switch to SISO on a antenna A
which isn't used by BT.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
For now, the firmware doesn't really use the field, but
it should be set to zero if there's no specific request.
Setting it to the max quota doesn't make sense.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Advertise driver's support for low priority scan.
Notice that this overwrites current setting by mac80211 which depends
only on hw scan support.
This scan priority can be configured by user space application
and it affects scan continuity, low priority scan
will be more fragmented scan.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Bit 0 in the scan offloading flags asks the filter
to pass all the results (instead of filtering them,
by default), rather than the other way around (like
it is defined and used today).
Fix the flag name appropriately, and fix its user.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This allows to see the content of the NVM the driver reads.
Note that the output is in binary, and requires some
external user space tool to display the data properly.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
If we haven't loaded the D3 image yet and a failure in the suspend
process occurs, we shouldn't restart the HW, because we're still
running the D0 image.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This is just a helper function to go from the mac80211
station struct to our internal one, to later allow us
to avoid temporary 'mvmsta' variables.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
valid_rx_ant is a bitmask of available antennas and not the number
of Rx antennas. Use num_of_ant and remove duplicate definitions
in both dvm and mvm.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
inta is checked to be zero in a IRQ_NONE branch so afterwards it
cannot be zero as it is never modified.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
[reword the patch title and fix comment]
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
These devices are not sold as discrete modules but are
rather soldered down to the board.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Latest tests have shown that when BT is active and has
connections but the traffic is low, the WiFi aggregation can
be large up to 4000us without noticeable impact on BT.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Add more bit field definitions used in LQ flags.
Also rename the first bit to a shorter name.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Abstract the copy_from_user() pattern into the macros defining
debugfs files, reducing the code and making adding new files
safer by avoiding having deal with copy_from_user() directly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
There's really no reason to use void *dbgfs_data
rather than a struct iwl_mvm *mvm, so do that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The debugfs file is getting pretty large and mixed up between
code for the hardware and code for each interface (the two
aren't even clearly separated in the code). Make it easier to
handle by splitting the per-interface code into a separate
file called debugfs-vif.c.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Just clean up the code a bit, in particular
* make all the debugfs writes follow the same pattern
with respect to buf/buf_size variables
* get rid of useless comments
* check return values of all file creations
* drop unnecessary parentheses
* remove an unused struct definition
* fix some whitespace
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The HT protection flags have been a mess for a long time,
this patch fixes all this.
The proper source of information for this is the
protection in the HT operation mode IE which is
propagated to bss_conf by mac80211.
1) No need to set the HT protection flags when the link
doesn't support HT.
2) We need to set the TGG protection when ERP is active.
Signed-off-by: Avri Altman <avri.altman@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Keeping connection can be useful also when testing d3
using the debugfs file (d3_test).
Save the vif to keep connection on, and consider it
when iterating over the interfaces.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Re-initialize rs when we get a rate_update hook called which
happens when remote STA changes bandwidth or sends a VHT opmode
notification.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When waking up from d3 due to disconnection event
(e.g. because of beacon loss), we should disconnect
immediately.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Even if d3_test_pme_ptr is not available, d3_test can still
be useful, e.g. by manually triggering resume (with ctrl-c),
and reading the wakeup reasons.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Refactor setting of VHT enabled rates in preparation of adding
some more logic there.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Remove the flags parameter which should be set to sync or async
according to whether this is called during sta init or not.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Info about VHT/HT rates wasn't printed properly when dumping
the rate scale table. Fix that and print more info. While at it
fix some other minor issues in the printing and prevent
overflowing the print buffer.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
After wait_event_timeout(), the condition must still be
true if it returns >0, in fact almost the last thing in
it is checking the condition again. It's therefore not
useful to check yet again in our code, clean it up.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Writting to fw_nmi entry will set DEVICE_SET_NMI_REG (0x00a01c30)
generating NMI that halts NIC CPU.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The transport layer doesn't need to know the TX_CMD id.
It can be set by the op_mode.
The transport layer still needs to know the layout of the
Tx command because of alignment issues and because of the
scratch pointer.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
If the next seqno returned by the firmware is 0, we return an error
(-16) in the iwl_mvm_get_last_nonqos_seq() function. This is because
we return an integer and don't use any casting when calculating the
last seqno from the one we received. Fix this by using a cast to u16
when doing the calculation, so we return 0xfff0, as we should.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Eran Harary